Re: MFGTools from NXP

[Ahmad Fatoum <a.fatoum@pengutronix.de>]

On 10/16/19 2:35 PM, Mihaita Ivascu wrote:
> No it does not. Still no devices listed.

Strange. What barebox version?

> 
> Thanks,
>       Mihaita
> 
> On Wed, Oct 16, 2019 at 1:36 PM Ahmad Fatoum <a.fatoum@pengutronix.de> wrote:
>>
>> On 10/16/19 1:28 PM, Mihaita Ivascu wrote:
>>> On Wed, Oct 16, 2019 at 11:53 AM Ahmad Fatoum <a.fatoum@pengutronix.de>
>>> wrote:
>>>>
>>>>
>>>> On 10/16/19 11:48 AM, Mihaita Ivascu wrote:
>>>>> On Wed, Oct 16, 2019 at 11:26 AM Ahmad Fatoum <a.fatoum@pengutronix.de>
>>> wrote:
>>>>>>
>>>>>> On 10/16/19 11:21 AM, Mihaita Ivascu wrote:
>>>>>>> Hello,
>>>>>>>
>>>>>>>    Thanks for your answer. Yes i am able to connect via PUTTY to the
>>> target.
>>>>>>>    Then I should use some adb commands in order to push the new
>>>>>>> barebox/firmware ? do you know where I could find some examples?
>>>>>>
>>>>>> fastboot device -l works normally on Linux. You need to check what you
>>> need
>>>>>> to do on Windows to do the same. You should only need the Fastboot
>>> utility
>>>>>> for this.
>>>>>>
>>>>> [mi] Yes I have both fastboot and adb installed on both Windows and
>>>>> Linux machines. In both cases it does not list any device.
>>>>>        The board is detected as fastboot android is windows device
>>>>> manager. But the fastboot and adb does not list it. same for Linux.
>>>>> Please see attachment
>>>>
>>>> Let's focus on Linux. You don't see a device there?
>>>> What does barebox say? Does it say 'multi_bind: creating Fastboot
>>> function'?
>>>> What does you Linux host's dmesg say?
>>>>
>>>
>>> barebox@Phytec phyCORE-i.MX6 Ultra Lite SOM:/ usbgadget -aA
>>> udc0: registering UDC driver [g_multi]
>>> multi_bind: creating Fastboot function
>>> multi_bind: creating ACM function
>>> g_multi usbgadget: Multifunction Composite Gadget
>>> g_multi usbgadget: userspace failed to provide iSerialNumber
>>> g_multi usbgadget: g_multi ready
>>> barebox@Phytec phyCORE-i.MX6 Ultra Lite SOM:/ g_multi usbgadget: high-speed
>>> config #1: Multifunction Composite Gadget
>>>
>>> dmesg:
>>>
>>> [   25.602275] usb 1-1.3: USB disconnect, device number 3
>>> [   28.359930] usb 1-1.3: new high-speed USB device number 5 using ehci-pci
>>> [   28.452971] usb 1-1.3: New USB device found, idVendor=1d6b,
>>> idProduct=0104
>>> [   28.452976] usb 1-1.3: New USB device strings: Mfr=0, Product=2,
>>> SerialNumber=0
>>> [   28.452980] usb 1-1.3: Product: Phytec phyCORE-i.MX6 Ultra Lite SOM
>>> [   28.457925] cdc_acm 1-1.3:1.1: ttyACM0: USB ACM device
>>>
>>>
>>> So I see the device on Linux. But fastboot does not list any device on
>>> Linux.
>>
>> sudo doesn't change this?
>>
>>>
>>>>  >
>>>>>>>
>>>>>>>    Also I have a question: purpose of this activity is for me to be
>>>>>>> able to flash some imx6ul boards that have no firmware: no barebox.
>>>>>>>    So I know hardware config for the port is otg mode but as I have no
>>>>>>> barebox running them before I am wondering if I will be able to
>>>>>>> connect via PUTTY if I do not set the ACM gadget from barebox?
>>>>>>
>>>>>> Check the Embest MarS board's environment in barebox master. It sets up
>>>>>> a fastboot gadget automatically on boot from imx-usb-loader.
>>>>>> You can adjust it to your liking.
>>>>>
>>>>>   [mi] I was not able to find any docs about this board. I will keep
>>>>> searching/asking in the nxp community. If you have already ahve any
>>>>> files related to it would be helpful. Thanks
>>>>
>>>> It's in the barebox next branch (not master, sorry), see here:
>>>>
>>> https://github.com/saschahauer/barebox/blob/next/arch/arm/boards/embest-marsboard/defaultenv-mars/init/fastboot
>>>>
>>>> You can copy and adjust the environment setup for your board.
>>>>
>>>>>>
>>>>>> Cheers
>>>>>> Ahmad
>>>>>>
>>>>>>>
>>>>>>> Thanks,
>>>>>>>       Mihaita
>>>>>>>
>>>>>>> On Wed, Oct 16, 2019 at 10:51 AM Ahmad Fatoum <a.fatoum@pengutronix.de>
>>> wrote:
>>>>>>>>
>>>>>>>> On 10/16/19 10:40 AM, Mihaita Ivascu wrote:
>>>>>>>>> Hello again,
>>>>>>>>>
>>>>>>>>>    I have the target in otg peripheral mode, ADB and fastboot
>>> drivers
>>>>>>>>> installed but fastboot does not list any device. The board is
>>> detected
>>>>>>>>> in device manager
>>>>>>>>
>>>>>>>> Try enabling the ACM gadget in barebox and connect with PuTTY and
>>> see if
>>>>>>>> at least that works. It worked for me on Windows with another i.MX
>>> board
>>>>>>>> a month ago.
>>>>>>>>
>>>>>>>> As for fastboot, I don't know how to configure it on Windows, but
>>> surely
>>>>>>>> Android Modding boards will have you covered there.
>>>>>>>>
>>>>>>>>>    Please see attachment. Any ideas how should I proceed? Thanks for
>>>>>>>>> the support.
>>>>>>>>
>>>>>>>> You can enable the ACM gadget in barebox and see if that works, I
>>> tested
>>>>>>>> it on Windows with an i.MX board a month ago
>>>>>>>>
>>>>>>>> Cheers
>>>>>>>> Ahmad
>>>>>>>>
>>>>>>>>>
>>>>>>>>> Thanks,
>>>>>>>>>       Mihaita
>>>>>>>>>
>>>>>>>>> On Wed, Oct 16, 2019 at 9:32 AM Mihaita Ivascu
>>>>>>>>> <mihaita_ivascu@trimble.com> wrote:
>>>>>>>>>>
>>>>>>>>>> Thanks. I have installed ADB and fastboot drivers for Win from
>>>>>>>>>>
>>> https://www.getdroidtips.com/how-to-install-adb-and-fastboot-on-windows/
>>>>>>>>>> I have installed according to the attachment.
>>>>>>>>>> But is not recognized in Windows. I did reboot the system after
>>>>>>>>>> installation but did not add any new env variable.
>>>>>>>>>>
>>>>>>>>>> H:\>fastboot devices -l
>>>>>>>>>> 'fastboot' is not recognized as an internal or external command,
>>>>>>>>>> operable program or batch file.
>>>>>>>>>>
>>>>>>>>>> Thanks,
>>>>>>>>>>       Mihaita
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> On Tue, Oct 15, 2019 at 4:44 PM Ahmad Fatoum <
>>> a.fatoum@pengutronix.de> wrote:
>>>>>>>>>>>
>>>>>>>>>>> On 10/15/19 4:41 PM, Mihaita Ivascu wrote:
>>>>>>>>>>>> barebox@Phytec phyCORE-i.MX6 Ultra Lite SOM:/ fastboot devices -l
>>>>>>>>>>> That's what you run on your host system, not on the target.
>>>>>>>>>>> --
>>>>>>>>>>> Pengutronix e.K.                           |
>>>         |
>>>>>>>>>>> Industrial Linux Solutions                 |
>>> http://www.pengutronix.de/  |
>>>>>>>>>>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone:
>>> +49-5121-206917-0    |
>>>>>>>>>>> Amtsgericht Hildesheim, HRA 2686           | Fax:
>>> +49-5121-206917-5555 |
>>>>>>>>
>>>>>>>>
>>>>>>>> --
>>>>>>>> Pengutronix e.K.                           |
>>>     |
>>>>>>>> Industrial Linux Solutions                 |
>>> http://www.pengutronix.de/  |
>>>>>>>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone:
>>> +49-5121-206917-0    |
>>>>>>>> Amtsgericht Hildesheim, HRA 2686           | Fax:
>>> +49-5121-206917-5555 |
>>>>>>>
>>>>>>
>>>>>>
>>>>>> --
>>>>>> Pengutronix e.K.                           |
>>>   |
>>>>>> Industrial Linux Solutions                 | http://www.pengutronix.de/
>>>  |
>>>>>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0
>>>    |
>>>>>> Amtsgericht Hildesheim, HRA 2686           | Fax:
>>> +49-5121-206917-5555 |
>>>>
>>>> --
>>>> Pengutronix e.K.                           |                             |
>>>> Industrial Linux Solutions                 | http://www.pengutronix.de/  |
>>>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
>>>> Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
>>>
>>
>> --
>> Pengutronix e.K.                           |                             |
>> Industrial Linux Solutions                 | http://www.pengutronix.de/  |
>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
>> Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
> 


-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox