From: Ahmad Fatoum <a.fatoum@pengutronix.de>
To: John Watts <contact@jookia.org>, Sascha Hauer <sha@pengutronix.de>
Cc: barebox@lists.infradead.org
Subject: Re: [PATCH 4/5] ARM: novena: Read Ethernet MAC address from EEPROM
Date: Wed, 25 Jan 2023 14:48:20 +0100 [thread overview]
Message-ID: <072ab8ce-d92f-8841-a44e-621a3ba345a4@pengutronix.de> (raw)
In-Reply-To: <Y9EvGHjLUX1ykAxU@novena-choice-citizen>
On 25.01.23 14:31, John Watts wrote:
> On Wed, Jan 25, 2023 at 09:19:23AM +0100, Sascha Hauer wrote:
>> Yes, normally it should be set up already, unless of course there is
>> some needed pinctrl configuration in an unrelated device tree node.
>>
>> Sascha
>
> Hi Sascha,
>
> Here's what I think is going on:
>
> - The I2C line requires 3v3_DELAYED for pull-ups
> - The EEPROM requires 3v3_DELAYED for power
> - 3v3_DELAYED requires VGEN5 from the PMIC (acts as a gate)
> - The PMIC is loaded after the EEPROM
>
> Most things on the board require these delayed rails, so I'm wondering
> what the approach should be here. Should I:
>
> - Rewrite the device tree to reference these delayed rails
> - Probe the PMIC first
>
> I did try this:
>
> reg_3p3v: regulator-3p3v {
> compatible = "regulator-fixed";
> regulator-name = "3P3V_DELAYED";
> regulator-min-microvolt = <3300000>;
> regulator-max-microvolt = <3300000>;
> regulator-always-on;
> gate-supply = <®_vgen6>;
regulator-fixed only understands vin-supply.
> };
>
> But Barebox doesn't seem to see the 'regulator-always-on' as
> 'start immediately'.
For this to work we'd need:
of_devices_ensure_probed_by_property("regulator-always-on");
of_devices_ensure_probed_by_property("regulator-boot-on");
somewhere in generic code. Currently, these properties are only
consulted when the device is actually probed.
I actually updated the eeprom node to use
> reg_3p3v as vcc-supply and things were still probed in the wrong order.
That's odd. You can enable CONFIG_DEBUG_PROBES to see in what order
probes happened and at what depth (each probe within a probe is
indented more than its parent).
Cheers,
Ahmad
>
> John.
>
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
next prev parent reply other threads:[~2023-01-25 13:49 UTC|newest]
Thread overview: 52+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-01-22 17:51 [PATCH 0/5] Add support for the Kosagi Novena board John Watts
2023-01-22 17:51 ` [PATCH 1/5] ARM: novena: Add " John Watts
2023-01-23 9:20 ` Sascha Hauer
2023-01-22 17:51 ` [PATCH 2/5] ARM: novena: Setup RAM using static configuration John Watts
2023-01-22 17:51 ` [PATCH 3/5] ARM: novena: Require the PFUZE regulator John Watts
2023-01-22 17:51 ` [PATCH 4/5] ARM: novena: Read Ethernet MAC address from EEPROM John Watts
2023-01-23 9:33 ` Sascha Hauer
2023-01-23 9:55 ` John Watts
2023-01-24 18:35 ` John Watts
2023-01-25 8:04 ` Sascha Hauer
2023-01-25 8:11 ` John Watts
2023-01-25 8:19 ` Sascha Hauer
2023-01-25 13:31 ` John Watts
2023-01-25 13:48 ` Ahmad Fatoum [this message]
2023-01-25 14:04 ` John Watts
2023-01-25 14:16 ` Ahmad Fatoum
2023-01-25 14:28 ` John Watts
2023-01-25 14:33 ` Ahmad Fatoum
2023-01-25 14:50 ` John Watts
2023-01-25 15:42 ` Sascha Hauer
2023-01-25 16:13 ` John Watts
2023-01-22 17:51 ` [PATCH 5/5] ARM: novena: Use DDR3 information from SPD EEPROM John Watts
2023-01-22 23:20 ` John Watts
2023-01-25 16:42 ` [PATCH v2 0/4] Add support for the Kosagi Novena board John Watts
2023-01-25 16:42 ` [PATCH v2 1/4] ARM: novena: Add " John Watts
2023-01-25 19:33 ` Marco Felsch
2023-01-26 7:25 ` Sascha Hauer
2023-01-26 7:50 ` John Watts
2023-01-26 9:13 ` Marco Felsch
2023-01-25 16:42 ` [PATCH v2 2/4] ARM: novena: Setup RAM using static configuration John Watts
2023-01-25 19:39 ` Marco Felsch
2023-01-26 7:54 ` John Watts
2023-01-26 8:11 ` Sascha Hauer
2023-01-26 9:14 ` Marco Felsch
2023-01-25 16:42 ` [PATCH v2 3/4] ARM: novena: Read Ethernet MAC address from EEPROM John Watts
2023-01-25 20:07 ` Marco Felsch
2023-01-26 8:05 ` John Watts
2023-01-26 9:07 ` Marco Felsch
2023-01-25 16:42 ` [PATCH v2 4/4] ARM: novena: Use DDR3 information from SPD EEPROM John Watts
2023-01-29 23:27 ` [PATCH v3 0/4] Add support for the Kosagi Novena board John Watts
2023-01-29 23:27 ` [PATCH v3 1/4] ARM: novena: Add " John Watts
2023-01-30 20:13 ` Marco Felsch
2023-01-30 20:26 ` John Watts
2023-01-31 9:45 ` Marco Felsch
2023-01-29 23:27 ` [PATCH v3 2/4] ARM: novena: Setup RAM using static configuration John Watts
2023-01-29 23:27 ` [PATCH v3 3/4] ARM: novena: Read Ethernet MAC address from EEPROM John Watts
2023-01-30 20:04 ` Marco Felsch
2023-01-30 20:25 ` John Watts
2023-01-31 9:29 ` Marco Felsch
2023-01-29 23:28 ` [PATCH v3 4/4] ARM: novena: Use DDR3 information from SPD EEPROM John Watts
2023-01-30 20:18 ` Marco Felsch
2023-01-30 20:41 ` John Watts
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=072ab8ce-d92f-8841-a44e-621a3ba345a4@pengutronix.de \
--to=a.fatoum@pengutronix.de \
--cc=barebox@lists.infradead.org \
--cc=contact@jookia.org \
--cc=sha@pengutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox