* [PATCH 1/3] at91: add HAVE_NAND_ATMEL_BUSWIDTH_16 to Enable 16-bit data bus interface @ 2010-09-18 2:18 Jean-Christophe PLAGNIOL-VILLARD 2010-09-18 2:18 ` [PATCH 2/3] at91sam9263: move MACH_HAS_LOWLEVEL_INIT to board Jean-Christophe PLAGNIOL-VILLARD 2010-09-18 2:18 ` [PATCH 3/3] Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC Jean-Christophe PLAGNIOL-VILLARD 0 siblings, 2 replies; 4+ messages in thread From: Jean-Christophe PLAGNIOL-VILLARD @ 2010-09-18 2:18 UTC (permalink / raw) To: barebox; +Cc: Patrice Vilchez, Nicolas Ferre Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Patrice Vilchez <patrice.vilchez@atmel.com> --- arch/arm/mach-at91/Kconfig | 16 ++++++++++++++++ 1 files changed, 16 insertions(+), 0 deletions(-) diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index 99d0f4d..1b006a1 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -10,6 +10,9 @@ config BOARDINFO default "Bucyrus MMC-CPU" if MACH_MMCCPU default "Ronetix PM9263" if MACH_PM9263 +config HAVE_NAND_ATMEL_BUSWIDTH_16 + bool + comment "Atmel AT91 System-on-Chip" choice @@ -38,6 +41,7 @@ choice config MACH_AT91SAM9260EK bool "Atmel AT91SAM9260-EK" + select HAVE_NAND_ATMEL_BUSWIDTH_16 help Say y here if you are using Atmel's AT91SAM9260-EK Evaluation board @@ -54,6 +58,7 @@ choice config MACH_AT91SAM9263EK bool "Atmel AT91SAM9263-EK" + select HAVE_NAND_ATMEL_BUSWIDTH_16 help Say y here if you are using Atmel's AT91SAM9263-EK Evaluation board @@ -71,4 +76,15 @@ endchoice endif +# ---------------------------------------------------------- + +comment "AT91 Board Options" + +config MTD_NAND_ATMEL_BUSWIDTH_16 + bool "Enable 16-bit data bus interface to NAND flash" + depends on HAVE_NAND_ATMEL_BUSWIDTH_16 + help + On AT91SAM926x boards both types of NAND flash can be present + (8 and 16 bit data bus width). + endif -- 1.7.1 _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH 2/3] at91sam9263: move MACH_HAS_LOWLEVEL_INIT to board 2010-09-18 2:18 [PATCH 1/3] at91: add HAVE_NAND_ATMEL_BUSWIDTH_16 to Enable 16-bit data bus interface Jean-Christophe PLAGNIOL-VILLARD @ 2010-09-18 2:18 ` Jean-Christophe PLAGNIOL-VILLARD 2010-09-18 2:18 ` [PATCH 3/3] Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC Jean-Christophe PLAGNIOL-VILLARD 1 sibling, 0 replies; 4+ messages in thread From: Jean-Christophe PLAGNIOL-VILLARD @ 2010-09-18 2:18 UTC (permalink / raw) To: barebox; +Cc: Patrice Vilchez, Nicolas Ferre as not all board support it Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Patrice Vilchez <patrice.vilchez@atmel.com> --- arch/arm/mach-at91/Kconfig | 3 ++- 1 files changed, 2 insertions(+), 1 deletions(-) diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index 1b006a1..288ee6f 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -26,7 +26,6 @@ config ARCH_AT91SAM9260 config ARCH_AT91SAM9263 bool "AT91SAM9263" select CPU_ARM926T - select MACH_HAS_LOWLEVEL_INIT select HAS_MACB endchoice @@ -58,6 +57,7 @@ choice config MACH_AT91SAM9263EK bool "Atmel AT91SAM9263-EK" + select MACH_HAS_LOWLEVEL_INIT select HAVE_NAND_ATMEL_BUSWIDTH_16 help Say y here if you are using Atmel's AT91SAM9263-EK Evaluation board @@ -69,6 +69,7 @@ config MACH_MMCCPU config MACH_PM9263 bool "Ronetix PM9263" + select MACH_HAS_LOWLEVEL_INIT help Say y here if you are using the Ronetix PM9263 Board -- 1.7.1 _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH 3/3] Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC. 2010-09-18 2:18 [PATCH 1/3] at91: add HAVE_NAND_ATMEL_BUSWIDTH_16 to Enable 16-bit data bus interface Jean-Christophe PLAGNIOL-VILLARD 2010-09-18 2:18 ` [PATCH 2/3] at91sam9263: move MACH_HAS_LOWLEVEL_INIT to board Jean-Christophe PLAGNIOL-VILLARD @ 2010-09-18 2:18 ` Jean-Christophe PLAGNIOL-VILLARD 2010-09-18 2:26 ` [PATCH 3/3 v2] " Jean-Christophe PLAGNIOL-VILLARD 1 sibling, 1 reply; 4+ messages in thread From: Jean-Christophe PLAGNIOL-VILLARD @ 2010-09-18 2:18 UTC (permalink / raw) To: barebox; +Cc: Patrice Vilchez, Nicolas Ferre AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed. We created a new board for this device but based the chip support directly on 9260 files with little updates. Here is the chip page on Atmel wabsite: http://atmel.com/dyn/products/product_card.asp?part_id=4337 Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Patrice Vilchez <patrice.vilchez@atmel.com> --- arch/arm/Makefile | 1 + arch/arm/boards/at91sam9260ek/init.c | 21 +++++++++++++++- arch/arm/configs/at91sam9g20ek_defconfig | 39 ++++++++++++++++++++++++++++++ arch/arm/mach-at91/Kconfig | 33 +++++++++++++++++++++++++ arch/arm/mach-at91/Makefile | 1 + arch/arm/mach-at91/lowlevel_init.S | 3 +- 6 files changed, 96 insertions(+), 2 deletions(-) create mode 100644 arch/arm/configs/at91sam9g20ek_defconfig diff --git a/arch/arm/Makefile b/arch/arm/Makefile index e404ad0..77b6cf4 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -52,6 +52,7 @@ board-$(CONFIG_MACH_A9M2410) := a9m2410 board-$(CONFIG_MACH_A9M2440) := a9m2440 board-$(CONFIG_MACH_AT91SAM9260EK) := at91sam9260ek board-$(CONFIG_MACH_AT91SAM9263EK) := at91sam9263ek +board-$(CONFIG_MACH_AT91SAM9G20EK) := at91sam9260ek board-$(CONFIG_MACH_EDB9301) := edb93xx board-$(CONFIG_MACH_EDB9302) := edb93xx board-$(CONFIG_MACH_EDB9302A) := edb93xx diff --git a/arch/arm/boards/at91sam9260ek/init.c b/arch/arm/boards/at91sam9260ek/init.c index 7bb3c45..966dd2f 100644 --- a/arch/arm/boards/at91sam9260ek/init.c +++ b/arch/arm/boards/at91sam9260ek/init.c @@ -40,6 +40,25 @@ #include <mach/at91_pmc.h> #include <mach/at91_rstc.h> +/* + * board revision encoding + * bit 0: + * 0 => 1 mmc + * 1 => 2 mmcs (board from revision C) + */ +#define HAVE_2MMC (1 << 0) +static void ek_set_board_type(void) +{ + if (machine_is_at91sam9g20ek()) { + armlinux_set_architecture(MACH_TYPE_AT91SAM9G20EK); +#ifdef CONFIG_AT91_HAVE_2MMC + armlinux_set_revision(HAVE_2MMC); +#endif + } else { + armlinux_set_architecture(MACH_TYPE_AT91SAM9260EK); + } +} + static struct atmel_nand_data nand_pdata = { .ale = 21, .cle = 22, @@ -130,7 +149,7 @@ static int at91sam9260ek_devices_init(void) at91_add_device_sdram(64 * 1024 * 1024); armlinux_set_bootparams((void *)(AT91_CHIPSELECT_1 + 0x100)); - armlinux_set_architecture(MACH_TYPE_AT91SAM9260EK); + ek_set_board_type(); devfs_add_partition("nand0", 0x00000, 0x80000, PARTITION_FIXED, "self_raw"); dev_add_bb_dev("self_raw", "self0"); diff --git a/arch/arm/configs/at91sam9g20ek_defconfig b/arch/arm/configs/at91sam9g20ek_defconfig new file mode 100644 index 0000000..bc7c242 --- /dev/null +++ b/arch/arm/configs/at91sam9g20ek_defconfig @@ -0,0 +1,39 @@ +CONFIG_ARCH_AT91SAM9G20=y +CONFIG_MACH_AT91SAM9G20EK=y +CONFIG_AT91_HAVE_2MMC=y +CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y +CONFIG_PROMPT="9G20-EK:" +CONFIG_LONGHELP=y +CONFIG_GLOB=y +CONFIG_PROMPT_HUSH_PS2="y" +CONFIG_CMDLINE_EDITING=y +CONFIG_AUTO_COMPLETE=y +CONFIG_PARTITION=y +CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/at91sam9260ek/env" +CONFIG_CMD_EDIT=y +CONFIG_CMD_SLEEP=y +CONFIG_CMD_SAVEENV=y +CONFIG_CMD_LOADENV=y +CONFIG_CMD_EXPORT=y +CONFIG_CMD_PRINTENV=y +CONFIG_CMD_READLINE=y +CONFIG_CMD_MEMINFO=y +CONFIG_CMD_CRC=y +CONFIG_CMD_MTEST=y +CONFIG_CMD_MTEST_ALTERNATIVE=y +CONFIG_CMD_FLASH=y +CONFIG_CMD_BOOTM_SHOW_TYPE=y +CONFIG_CMD_RESET=y +CONFIG_CMD_GO=y +CONFIG_CMD_TIMEOUT=y +CONFIG_CMD_PARTITION=y +CONFIG_CMD_GPIO=y +CONFIG_NET=y +CONFIG_NET_DHCP=y +CONFIG_NET_PING=y +CONFIG_NET_TFTP=y +CONFIG_DRIVER_NET_MACB=y +# CONFIG_SPI is not set +CONFIG_I2C=y +CONFIG_DRIVER_CFI=y +CONFIG_CFI_BUFFER_WRITE=y diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index 288ee6f..1491161 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -7,6 +7,7 @@ config ARCH_TEXT_BASE config BOARDINFO default "Atmel 91SAM9260-EK" if MACH_AT91SAM9260EK default "Atmel at91sam9263-ek" if MACH_AT91SAM9263EK + default "Atmel at91sam9g20-ek" if MACH_AT91SAM9G20EK default "Bucyrus MMC-CPU" if MACH_MMCCPU default "Ronetix PM9263" if MACH_PM9263 @@ -28,6 +29,11 @@ config ARCH_AT91SAM9263 select CPU_ARM926T select HAS_MACB +config ARCH_AT91SAM9G20 + bool "AT91SAM9G20" + select CPU_ARM926T + select HAS_MACB + endchoice # ---------------------------------------------------------- @@ -50,6 +56,25 @@ endif # ---------------------------------------------------------- +if ARCH_AT91SAM9G20 + +choice + + prompt "AT91SAM9G20 Board Type" + +config MACH_AT91SAM9G20EK + bool "Atmel AT91SAM9G20-EK Evaluation Kit" + select HAVE_NAND_ATMEL_BUSWIDTH_16 + help + Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit + that embeds only one SD/MMC slot. + +endchoice + +endif + +# ---------------------------------------------------------- + if ARCH_AT91SAM9263 choice @@ -88,4 +113,12 @@ config MTD_NAND_ATMEL_BUSWIDTH_16 On AT91SAM926x boards both types of NAND flash can be present (8 and 16 bit data bus width). +config AT91_HAVE_2MMC + bool "Have 2 MMC" + depends on MACH_AT91SAM9G20EK + help + Select this if you are using an Atmel AT91SAM9G20-EK Evaluation Kit + with 2 SD/MMC Slots. This is the case for AT91SAM9G20-EK rev. C and + onwards. + endif diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile index 2878b04..1bedadb 100644 --- a/arch/arm/mach-at91/Makefile +++ b/arch/arm/mach-at91/Makefile @@ -5,3 +5,4 @@ obj-$(CONFIG_MACH_DO_LOWLEVEL_INIT) += lowlevel_init.o # CPU-specific support obj-$(CONFIG_ARCH_AT91SAM9260) += at91sam9260.o at91sam926x_time.o at91sam9260_devices.o sam9_smc.o obj-$(CONFIG_ARCH_AT91SAM9263) += at91sam9263.o at91sam926x_time.o at91sam9263_devices.o sam9_smc.o +obj-$(CONFIG_ARCH_AT91SAM9G20) += at91sam9260.o at91sam926x_time.o at91sam9260_devices.o sam9_smc.o diff --git a/arch/arm/mach-at91/lowlevel_init.S b/arch/arm/mach-at91/lowlevel_init.S index 497cc0d..0b29866 100644 --- a/arch/arm/mach-at91/lowlevel_init.S +++ b/arch/arm/mach-at91/lowlevel_init.S @@ -193,7 +193,8 @@ SMRDATA: .word CONFIG_SYS_PIOD_PPUDR_VAL .word (AT91_BASE_SYS + AT91_PIOD + PIO_ASR) .word CONFIG_SYS_PIOD_PPUDR_VAL -#elif defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9261) +#elif defined(CONFIG_AT91SAM9260) || defined(CONFIG_AT91SAM9261) \ + || defined(CONFIG_AT91SAM9G20) .word (AT91_BASE_SYS + AT91_PIOC + PIO_PDR) .word CONFIG_SYS_PIOC_PDR_VAL1 .word (AT91_BASE_SYS + AT91_PIOC + PIO_PUDR) -- 1.7.1 _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH 3/3 v2] Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC. 2010-09-18 2:18 ` [PATCH 3/3] Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC Jean-Christophe PLAGNIOL-VILLARD @ 2010-09-18 2:26 ` Jean-Christophe PLAGNIOL-VILLARD 0 siblings, 0 replies; 4+ messages in thread From: Jean-Christophe PLAGNIOL-VILLARD @ 2010-09-18 2:26 UTC (permalink / raw) To: barebox; +Cc: Patrice Vilchez, Nicolas Ferre AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed. We created a new board for this device but based the chip support directly on 9260 files with little updates. Here is the chip page on Atmel wabsite: http://atmel.com/dyn/products/product_card.asp?part_id=4337 Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Patrice Vilchez <patrice.vilchez@atmel.com> --- v2: fix wrong ARCH name in the lowlevel arch/arm/Makefile | 1 + arch/arm/boards/at91sam9260ek/init.c | 21 +++++++++++++++- arch/arm/configs/at91sam9g20ek_defconfig | 39 ++++++++++++++++++++++++++++++ arch/arm/mach-at91/Kconfig | 33 +++++++++++++++++++++++++ arch/arm/mach-at91/Makefile | 1 + arch/arm/mach-at91/lowlevel_init.S | 3 +- 6 files changed, 96 insertions(+), 2 deletions(-) create mode 100644 arch/arm/configs/at91sam9g20ek_defconfig diff --git a/arch/arm/Makefile b/arch/arm/Makefile index e404ad0..77b6cf4 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -52,6 +52,7 @@ board-$(CONFIG_MACH_A9M2410) := a9m2410 board-$(CONFIG_MACH_A9M2440) := a9m2440 board-$(CONFIG_MACH_AT91SAM9260EK) := at91sam9260ek board-$(CONFIG_MACH_AT91SAM9263EK) := at91sam9263ek +board-$(CONFIG_MACH_AT91SAM9G20EK) := at91sam9260ek board-$(CONFIG_MACH_EDB9301) := edb93xx board-$(CONFIG_MACH_EDB9302) := edb93xx board-$(CONFIG_MACH_EDB9302A) := edb93xx diff --git a/arch/arm/boards/at91sam9260ek/init.c b/arch/arm/boards/at91sam9260ek/init.c index 7bb3c45..966dd2f 100644 --- a/arch/arm/boards/at91sam9260ek/init.c +++ b/arch/arm/boards/at91sam9260ek/init.c @@ -40,6 +40,25 @@ #include <mach/at91_pmc.h> #include <mach/at91_rstc.h> +/* + * board revision encoding + * bit 0: + * 0 => 1 mmc + * 1 => 2 mmcs (board from revision C) + */ +#define HAVE_2MMC (1 << 0) +static void ek_set_board_type(void) +{ + if (machine_is_at91sam9g20ek()) { + armlinux_set_architecture(MACH_TYPE_AT91SAM9G20EK); +#ifdef CONFIG_AT91_HAVE_2MMC + armlinux_set_revision(HAVE_2MMC); +#endif + } else { + armlinux_set_architecture(MACH_TYPE_AT91SAM9260EK); + } +} + static struct atmel_nand_data nand_pdata = { .ale = 21, .cle = 22, @@ -130,7 +149,7 @@ static int at91sam9260ek_devices_init(void) at91_add_device_sdram(64 * 1024 * 1024); armlinux_set_bootparams((void *)(AT91_CHIPSELECT_1 + 0x100)); - armlinux_set_architecture(MACH_TYPE_AT91SAM9260EK); + ek_set_board_type(); devfs_add_partition("nand0", 0x00000, 0x80000, PARTITION_FIXED, "self_raw"); dev_add_bb_dev("self_raw", "self0"); diff --git a/arch/arm/configs/at91sam9g20ek_defconfig b/arch/arm/configs/at91sam9g20ek_defconfig new file mode 100644 index 0000000..bc7c242 --- /dev/null +++ b/arch/arm/configs/at91sam9g20ek_defconfig @@ -0,0 +1,39 @@ +CONFIG_ARCH_AT91SAM9G20=y +CONFIG_MACH_AT91SAM9G20EK=y +CONFIG_AT91_HAVE_2MMC=y +CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y +CONFIG_PROMPT="9G20-EK:" +CONFIG_LONGHELP=y +CONFIG_GLOB=y +CONFIG_PROMPT_HUSH_PS2="y" +CONFIG_CMDLINE_EDITING=y +CONFIG_AUTO_COMPLETE=y +CONFIG_PARTITION=y +CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/at91sam9260ek/env" +CONFIG_CMD_EDIT=y +CONFIG_CMD_SLEEP=y +CONFIG_CMD_SAVEENV=y +CONFIG_CMD_LOADENV=y +CONFIG_CMD_EXPORT=y +CONFIG_CMD_PRINTENV=y +CONFIG_CMD_READLINE=y +CONFIG_CMD_MEMINFO=y +CONFIG_CMD_CRC=y +CONFIG_CMD_MTEST=y +CONFIG_CMD_MTEST_ALTERNATIVE=y +CONFIG_CMD_FLASH=y +CONFIG_CMD_BOOTM_SHOW_TYPE=y +CONFIG_CMD_RESET=y +CONFIG_CMD_GO=y +CONFIG_CMD_TIMEOUT=y +CONFIG_CMD_PARTITION=y +CONFIG_CMD_GPIO=y +CONFIG_NET=y +CONFIG_NET_DHCP=y +CONFIG_NET_PING=y +CONFIG_NET_TFTP=y +CONFIG_DRIVER_NET_MACB=y +# CONFIG_SPI is not set +CONFIG_I2C=y +CONFIG_DRIVER_CFI=y +CONFIG_CFI_BUFFER_WRITE=y diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index 288ee6f..1491161 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -7,6 +7,7 @@ config ARCH_TEXT_BASE config BOARDINFO default "Atmel 91SAM9260-EK" if MACH_AT91SAM9260EK default "Atmel at91sam9263-ek" if MACH_AT91SAM9263EK + default "Atmel at91sam9g20-ek" if MACH_AT91SAM9G20EK default "Bucyrus MMC-CPU" if MACH_MMCCPU default "Ronetix PM9263" if MACH_PM9263 @@ -28,6 +29,11 @@ config ARCH_AT91SAM9263 select CPU_ARM926T select HAS_MACB +config ARCH_AT91SAM9G20 + bool "AT91SAM9G20" + select CPU_ARM926T + select HAS_MACB + endchoice # ---------------------------------------------------------- @@ -50,6 +56,25 @@ endif # ---------------------------------------------------------- +if ARCH_AT91SAM9G20 + +choice + + prompt "AT91SAM9G20 Board Type" + +config MACH_AT91SAM9G20EK + bool "Atmel AT91SAM9G20-EK Evaluation Kit" + select HAVE_NAND_ATMEL_BUSWIDTH_16 + help + Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit + that embeds only one SD/MMC slot. + +endchoice + +endif + +# ---------------------------------------------------------- + if ARCH_AT91SAM9263 choice @@ -88,4 +113,12 @@ config MTD_NAND_ATMEL_BUSWIDTH_16 On AT91SAM926x boards both types of NAND flash can be present (8 and 16 bit data bus width). +config AT91_HAVE_2MMC + bool "Have 2 MMC" + depends on MACH_AT91SAM9G20EK + help + Select this if you are using an Atmel AT91SAM9G20-EK Evaluation Kit + with 2 SD/MMC Slots. This is the case for AT91SAM9G20-EK rev. C and + onwards. + endif diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile index 2878b04..1bedadb 100644 --- a/arch/arm/mach-at91/Makefile +++ b/arch/arm/mach-at91/Makefile @@ -5,3 +5,4 @@ obj-$(CONFIG_MACH_DO_LOWLEVEL_INIT) += lowlevel_init.o # CPU-specific support obj-$(CONFIG_ARCH_AT91SAM9260) += at91sam9260.o at91sam926x_time.o at91sam9260_devices.o sam9_smc.o obj-$(CONFIG_ARCH_AT91SAM9263) += at91sam9263.o at91sam926x_time.o at91sam9263_devices.o sam9_smc.o +obj-$(CONFIG_ARCH_AT91SAM9G20) += at91sam9260.o at91sam926x_time.o at91sam9260_devices.o sam9_smc.o diff --git a/arch/arm/mach-at91/lowlevel_init.S b/arch/arm/mach-at91/lowlevel_init.S index 497cc0d..8a0ae02 100644 --- a/arch/arm/mach-at91/lowlevel_init.S +++ b/arch/arm/mach-at91/lowlevel_init.S @@ -193,7 +193,8 @@ SMRDATA: .word CONFIG_SYS_PIOD_PPUDR_VAL .word (AT91_BASE_SYS + AT91_PIOD + PIO_ASR) .word CONFIG_SYS_PIOD_PPUDR_VAL -#elif defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9261) +#elif defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9261) \ + || defined(CONFIG_ARCH_AT91SAM9G20) .word (AT91_BASE_SYS + AT91_PIOC + PIO_PDR) .word CONFIG_SYS_PIOC_PDR_VAL1 .word (AT91_BASE_SYS + AT91_PIOC + PIO_PUDR) -- 1.7.1 _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2010-09-18 2:27 UTC | newest] Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2010-09-18 2:18 [PATCH 1/3] at91: add HAVE_NAND_ATMEL_BUSWIDTH_16 to Enable 16-bit data bus interface Jean-Christophe PLAGNIOL-VILLARD 2010-09-18 2:18 ` [PATCH 2/3] at91sam9263: move MACH_HAS_LOWLEVEL_INIT to board Jean-Christophe PLAGNIOL-VILLARD 2010-09-18 2:18 ` [PATCH 3/3] Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC Jean-Christophe PLAGNIOL-VILLARD 2010-09-18 2:26 ` [PATCH 3/3 v2] " Jean-Christophe PLAGNIOL-VILLARD
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox