mail archive of the barebox mailing list
 help / color / mirror / Atom feed
From: Juergen Beisert <jbe@pengutronix.de>
To: barebox@lists.infradead.org
Subject: [PATCH 2/4] Add the driver for the i.MX23 debug UART
Date: Mon, 11 Oct 2010 11:06:58 +0200	[thread overview]
Message-ID: <1286788020-14077-3-git-send-email-jbe@pengutronix.de> (raw)
In-Reply-To: <1286788020-14077-1-git-send-email-jbe@pengutronix.de>

The i.MX23 comes with a special UART dedicated for debugging purposes. This one
is mostly used for the console the user can reach.

Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
---
 drivers/serial/Kconfig      |    5 +
 drivers/serial/Makefile     |    1 +
 drivers/serial/stm-serial.c |  202 +++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 208 insertions(+), 0 deletions(-)
 create mode 100644 drivers/serial/stm-serial.c

diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index c7ea2d9..3a8882f 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -18,6 +18,11 @@ config DRIVER_SERIAL_IMX
 	default y
 	bool "i.MX serial driver"
 
+config DRIVER_SERIAL_STM378X
+	depends on ARCH_STM
+	default y
+	bool "i.MX23 serial driver"
+
 config DRIVER_SERIAL_NETX
 	depends on ARCH_NETX
 	default y
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index 959290e..9f0e12b 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -7,6 +7,7 @@
 obj-$(CONFIG_DRIVER_SERIAL_ARM_DCC)		+= arm_dcc.o
 obj-$(CONFIG_SERIAL_AMBA_PL011) += amba-pl011.o
 obj-$(CONFIG_DRIVER_SERIAL_IMX)			+= serial_imx.o
+obj-$(CONFIG_DRIVER_SERIAL_STM378X)		+= stm-serial.o
 obj-$(CONFIG_DRIVER_SERIAL_ATMEL)		+= atmel.o
 obj-$(CONFIG_DRIVER_SERIAL_NETX)		+= serial_netx.o
 obj-$(CONFIG_DRIVER_SERIAL_LINUX_COMSOLE)	+= linux_console.o
diff --git a/drivers/serial/stm-serial.c b/drivers/serial/stm-serial.c
new file mode 100644
index 0000000..90563f5
--- /dev/null
+++ b/drivers/serial/stm-serial.c
@@ -0,0 +1,202 @@
+/*
+ * (C) Copyright 2010 Juergen Beisert - Pengutronix
+ *
+ * This code was inspired by some patches made for u-boot covered by:
+ * (c) 2007 Sascha Hauer <s.hauer@pengutronix.de>
+ * (C) Copyright 2009 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ */
+
+/*
+ * Note: This is the driver for the debug UART. There is
+ * only one of these UARTs on the Freescale/SigmaTel parts
+ */
+
+#include <common.h>
+#include <init.h>
+#include <notifier.h>
+#include <gpio.h>
+#include <asm/io.h>
+#include <mach/imx-regs.h>
+#include <mach/clock.h>
+
+#define UARTDBGDR 0x00
+#define UARTDBGFR 0x18
+# define TXFF (1 << 5)
+# define RXFE (1 << 4)
+#define UARTDBGIBRD 0x24
+#define UARTDBGFBRD 0x28
+#define UARTDBGLCR_H 0x2c
+# define WLEN8 (3 << 5)
+# define WLEN7 (2 << 5)
+# define WLEN6 (1 << 5)
+# define WLEN5 (0 << 5)
+# define FEN (1 << 4)
+#define UARTDBGCR 0x30
+# define UARTEN (1 << 0)
+# define TXE (1 << 8)
+# define RXE (1 << 9)
+#define UARTDBGIMSC 0x38
+
+struct stm_serial_local {
+	struct console_device cdev;
+	int baudrate;
+	struct notifier_block notify;
+};
+
+static void stm_serial_putc(struct console_device *cdev, char c)
+{
+	struct device_d *dev = cdev->dev;
+
+	/* Wait for room in TX FIFO */
+	while (readl(dev->map_base + UARTDBGFR) & TXFF)
+		;
+
+	writel(c, dev->map_base + UARTDBGDR);
+}
+
+static int stm_serial_tstc(struct console_device *cdev)
+{
+	struct device_d *dev = cdev->dev;
+
+	/* Check if RX FIFO is not empty */
+	return !(readl(dev->map_base + UARTDBGFR) & RXFE);
+}
+
+static int stm_serial_getc(struct console_device *cdev)
+{
+	struct device_d *dev = cdev->dev;
+
+	/* Wait while TX FIFO is empty */
+	while (readl(dev->map_base + UARTDBGFR) & RXFE)
+		;
+
+	return readl(dev->map_base + UARTDBGDR) & 0xff;
+}
+
+static void stm_serial_flush(struct console_device *cdev)
+{
+	struct device_d *dev = cdev->dev;
+
+	/* Wait for TX FIFO empty */
+	while (readl(dev->map_base + UARTDBGFR) & TXFF)
+		;
+}
+
+static int stm_serial_setbaudrate(struct console_device *cdev, int new_baudrate)
+{
+	struct device_d *dev = cdev->dev;
+	struct stm_serial_local *local = container_of(cdev, struct stm_serial_local, cdev);
+	uint32_t cr, lcr_h, quot;
+
+	/* Disable everything */
+	cr = readl(dev->map_base + UARTDBGCR);
+	writel(0, dev->map_base + UARTDBGCR);
+
+	/* Calculate and set baudrate */
+	quot = (imx_get_xclk() * 4000) / new_baudrate;
+	writel(quot & 0x3f, dev->map_base + UARTDBGFBRD);
+	writel(quot >> 6, dev->map_base + UARTDBGIBRD);
+
+	/* Set 8n1 mode, enable FIFOs */
+	lcr_h = WLEN8 | FEN;
+	writel(lcr_h, dev->map_base + UARTDBGLCR_H);
+
+	/* Re-enable debug UART */
+	writel(cr, dev->map_base + UARTDBGCR);
+
+	local->baudrate = new_baudrate;
+
+	return 0;
+}
+
+static int stm_clocksource_clock_change(struct notifier_block *nb, unsigned long event, void *data)
+{
+	struct stm_serial_local *local = container_of(nb, struct stm_serial_local, notify);
+
+	return stm_serial_setbaudrate(&local->cdev, local->baudrate);
+}
+
+static int stm_serial_init_port(struct console_device *cdev)
+{
+	struct device_d *dev = cdev->dev;
+	/*
+	 * If the board specific file registers this console we should force
+	 * the usage of the debug UART pins, to be able to let the user see
+	 * the output, even if the board file forgets to configure these pins.
+	 */
+	imx_gpio_mode(PWM1_DUART_TX);
+	imx_gpio_mode(PWM0_DUART_RX);
+
+	/* Disable UART */
+	writel(0, dev->map_base + UARTDBGCR);
+
+	/* Mask interrupts */
+	writel(0, dev->map_base + UARTDBGIMSC);
+
+	return 0;
+}
+
+static struct stm_serial_local stm_device = {
+	.cdev = {
+		.f_caps = CONSOLE_STDIN | CONSOLE_STDOUT | CONSOLE_STDERR,
+		.tstc = stm_serial_tstc,
+		.putc = stm_serial_putc,
+		.getc = stm_serial_getc,
+		.flush = stm_serial_flush,
+		.setbrg = stm_serial_setbaudrate,
+	},
+};
+
+static int stm_serial_probe(struct device_d *dev)
+{
+	stm_device.cdev.dev = dev;
+	dev->type_data = &stm_device.cdev;
+
+	stm_serial_init_port(&stm_device.cdev);
+	stm_serial_setbaudrate(&stm_device.cdev, CONFIG_BAUDRATE);
+
+	/* Enable UART */
+	writel(TXE | RXE | UARTEN, dev->map_base + UARTDBGCR);
+
+	console_register(&stm_device.cdev);
+	stm_device.notify.notifier_call = stm_clocksource_clock_change;
+	clock_register_client(&stm_device.notify);
+
+	return 0;
+}
+
+static void stm_serial_remove(struct device_d *dev)
+{
+	struct console_device *cdev = dev->type_data;
+
+	stm_serial_flush(cdev);
+}
+
+static struct driver_d stm_serial_driver = {
+        .name   = "stm_serial",
+        .probe  = stm_serial_probe,
+	.remove = stm_serial_remove,
+};
+
+static int stm_serial_init(void)
+{
+	register_driver(&stm_serial_driver);
+	return 0;
+}
+
+console_initcall(stm_serial_init);
-- 
1.7.2.3


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

  parent reply	other threads:[~2010-10-11  9:07 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2010-10-11  9:06 [PATCH v2] Add the i.MX23 architecure to barebox Juergen Beisert
2010-10-11  9:06 ` [PATCH 1/4] Add the basic files for the i.MX23/i.MX28 familiy of CPUs Juergen Beisert
2010-10-11  9:06 ` Juergen Beisert [this message]
2010-10-11  9:06 ` [PATCH 3/4] Add the i.MX23-EVK platform (WIP) Juergen Beisert
2010-10-11  9:11   ` Juergen Beisert
2010-10-11  9:07 ` [PATCH 4/4] Add the i.MX23 based Chumby " Juergen Beisert
  -- strict thread matches above, loose matches on Subject: below --
2010-10-07 14:59 Add the i.MX23/i.MX28 architecure Juergen Beisert
2010-10-07 14:59 ` [PATCH 2/4] Add the driver for the i.MX23 debug UART Juergen Beisert

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1286788020-14077-3-git-send-email-jbe@pengutronix.de \
    --to=jbe@pengutronix.de \
    --cc=barebox@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox