mail archive of the barebox mailing list
 help / color / mirror / Atom feed
From: franck.jullien@gmail.com
To: barebox@lists.infradead.org
Subject: [PATCH 2/4] mci: Add MCI over SPI support
Date: Wed, 23 Nov 2011 22:12:26 +0100	[thread overview]
Message-ID: <1322082748-17409-3-git-send-email-franck.jullien@gmail.com> (raw)
In-Reply-To: <1322082748-17409-1-git-send-email-franck.jullien@gmail.com>

From: Franck Jullien <franck.jullien@gmail.com>

This patch adds MMC over SPI support to mci-core.c and
mci_spi.c driver.

This driver is useful when SOC doesn't have built-in MCI
component. Tested with nios, 2Go SD-CARD and FAT file system.

Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
---
 drivers/mci/Kconfig    |   17 ++
 drivers/mci/Makefile   |    1 +
 drivers/mci/mci-core.c |   67 ++++++--
 drivers/mci/mci_spi.c  |  431 ++++++++++++++++++++++++++++++++++++++++++++++++
 include/mci.h          |   14 ++
 5 files changed, 514 insertions(+), 16 deletions(-)
 create mode 100644 drivers/mci/mci_spi.c

diff --git a/drivers/mci/Kconfig b/drivers/mci/Kconfig
index 0d5a0e0..ed88abb 100644
--- a/drivers/mci/Kconfig
+++ b/drivers/mci/Kconfig
@@ -80,4 +80,21 @@ config MCI_ATMEL
 	  Enable this entry to add support to read and write SD cards on a
 	  Atmel AT91.
 
+config MCI_SPI
+	bool "MMC/SD over SPI"
+	help
+	  Some systems access MMC/SD/SDIO cards using a SPI controller
+	  instead of using a "native" MMC/SD/SDIO controller.  This has a
+	  disadvantage of being relatively high overhead, but a compensating
+	  advantage of working on many systems without dedicated MMC/SD/SDIO
+	  controllers.
+
+config MMC_SPI_CRC_ON
+	bool "Enable CRC protection for transferts"
+	select CRC7
+	select CRC16
+	depends on MCI_SPI
+	help
+	  EEnable CRC protection for transferts
+
 endif
diff --git a/drivers/mci/Makefile b/drivers/mci/Makefile
index 4fc0046..d7482dc 100644
--- a/drivers/mci/Makefile
+++ b/drivers/mci/Makefile
@@ -5,3 +5,4 @@ obj-$(CONFIG_MCI_IMX) += imx.o
 obj-$(CONFIG_MCI_IMX_ESDHC) += imx-esdhc.o
 obj-$(CONFIG_MCI_OMAP_HSMMC) += omap_hsmmc.o
 obj-$(CONFIG_MCI_ATMEL) += atmel_mci.o
+obj-$(CONFIG_MCI_SPI) += mci_spi.o
diff --git a/drivers/mci/mci-core.c b/drivers/mci/mci-core.c
index 09f7e29..849c088 100644
--- a/drivers/mci/mci-core.c
+++ b/drivers/mci/mci-core.c
@@ -218,6 +218,7 @@ static int sd_send_op_cond(struct device_d *mci_dev)
 	int timeout = 1000;
 	int err;
 	unsigned voltages;
+	unsigned busy;
 
 	/*
 	 * Most cards do not answer if some reserved bits
@@ -237,7 +238,7 @@ static int sd_send_op_cond(struct device_d *mci_dev)
 		}
 
 		mci_setup_cmd(&cmd, SD_CMD_APP_SEND_OP_COND,
-			voltages | (mci->version == SD_VERSION_2 ? OCR_HCS : 0),
+			mmc_host_is_spi(host) ? 0 : (voltages | (mci->version == SD_VERSION_2 ? OCR_HCS : 0)),
 			MMC_RSP_R3);
 		err = mci_send_cmd(mci_dev, &cmd, NULL);
 		if (err) {
@@ -245,7 +246,13 @@ static int sd_send_op_cond(struct device_d *mci_dev)
 			return err;
 		}
 		udelay(1000);
-	} while ((!(cmd.response[0] & OCR_BUSY)) && timeout--);
+
+		if (mmc_host_is_spi(host))
+			busy = cmd.response[0] & R1_SPI_IDLE;
+		else
+			busy = !(cmd.response[0] & OCR_BUSY);
+
+	} while (busy && timeout--);
 
 	if (timeout <= 0) {
 		pr_debug("SD operation condition set timed out\n");
@@ -255,6 +262,13 @@ static int sd_send_op_cond(struct device_d *mci_dev)
 	if (mci->version != SD_VERSION_2)
 		mci->version = SD_VERSION_1_0;
 
+	if (mmc_host_is_spi(host)) { /* read OCR for spi */
+		mci_setup_cmd(&cmd, MMC_CMD_SPI_READ_OCR, 0, MMC_RSP_R3);
+		err = mci_send_cmd(mci_dev, &cmd, NULL);
+		if (err)
+			return err;
+	}
+
 	mci->ocr = cmd.response[0];
 
 	mci->high_capacity = ((mci->ocr & OCR_HCS) == OCR_HCS);
@@ -451,6 +465,7 @@ static int sd_switch(struct device_d *mci_dev, unsigned mode, unsigned group,
 static int sd_change_freq(struct device_d *mci_dev)
 {
 	struct mci *mci = GET_MCI_DATA(mci_dev);
+	struct mci_host *host = GET_MCI_PDATA(mci_dev);
 	struct mci_cmd cmd;
 	struct mci_data data;
 	uint32_t *switch_status = sector_buf;
@@ -458,6 +473,9 @@ static int sd_change_freq(struct device_d *mci_dev)
 	int timeout;
 	int err;
 
+	if (mmc_host_is_spi(host))
+		return 0;
+
 	pr_debug("Changing transfer frequency\n");
 	mci->card_caps = 0;
 
@@ -748,10 +766,23 @@ static int mci_startup(struct device_d *mci_dev)
 	struct mci_cmd cmd;
 	int err;
 
+#ifdef CONFIG_MMC_SPI_CRC_ON
+	if (mmc_host_is_spi(host)) { /* enable CRC check for spi */
+
+		mci_setup_cmd(&cmd, MMC_CMD_SPI_CRC_ON_OFF, 1, MMC_RSP_R1);
+		err = mci_send_cmd(mci_dev, &cmd, NULL);
+
+		if (err) {
+			pr_debug("Can't enable CRC check : %d\n", err);
+			return err;
+		}
+	}
+#endif
+
 	pr_debug("Put the Card in Identify Mode\n");
 
 	/* Put the Card in Identify Mode */
-	mci_setup_cmd(&cmd, MMC_CMD_ALL_SEND_CID, 0, MMC_RSP_R2);
+	mci_setup_cmd(&cmd, mmc_host_is_spi(host) ? MMC_CMD_SEND_CID : MMC_CMD_ALL_SEND_CID, 0, MMC_RSP_R2);
 	err = mci_send_cmd(mci_dev, &cmd, NULL);
 	if (err) {
 		pr_debug("Can't bring card into identify mode: %d\n", err);
@@ -768,12 +799,14 @@ static int mci_startup(struct device_d *mci_dev)
 	 * For SD cards, get the Relatvie Address.
 	 * This also puts the cards into Standby State
 	 */
-	pr_debug("Get/Set relative address\n");
-	mci_setup_cmd(&cmd, SD_CMD_SEND_RELATIVE_ADDR, mci->rca << 16, MMC_RSP_R6);
-	err = mci_send_cmd(mci_dev, &cmd, NULL);
-	if (err) {
-		pr_debug("Get/Set relative address failed: %d\n", err);
-		return err;
+	if (!mmc_host_is_spi(host)) { /* cmd not supported in spi */
+		pr_debug("Get/Set relative address\n");
+		mci_setup_cmd(&cmd, SD_CMD_SEND_RELATIVE_ADDR, mci->rca << 16, MMC_RSP_R6);
+		err = mci_send_cmd(mci_dev, &cmd, NULL);
+		if (err) {
+			pr_debug("Get/Set relative address failed: %d\n", err);
+			return err;
+		}
 	}
 
 	if (IS_SD(mci))
@@ -814,13 +847,15 @@ static int mci_startup(struct device_d *mci_dev)
 	pr_debug("Read block length: %u, Write block length: %u\n",
 		mci->read_bl_len, mci->write_bl_len);
 
-	pr_debug("Select the card, and put it into Transfer Mode\n");
-	/* Select the card, and put it into Transfer Mode */
-	mci_setup_cmd(&cmd, MMC_CMD_SELECT_CARD, mci->rca << 16, MMC_RSP_R1b);
-	err = mci_send_cmd(mci_dev, &cmd, NULL);
-	if (err) {
-		pr_debug("Putting in transfer mode failed: %d\n", err);
-		return err;
+	if (!mmc_host_is_spi(host)) { /* cmd not supported in spi */
+		pr_debug("Select the card, and put it into Transfer Mode\n");
+		/* Select the card, and put it into Transfer Mode */
+		mci_setup_cmd(&cmd, MMC_CMD_SELECT_CARD, mci->rca << 16, MMC_RSP_R1b);
+		err = mci_send_cmd(mci_dev, &cmd, NULL);
+		if (err) {
+			pr_debug("Putting in transfer mode failed: %d\n", err);
+			return err;
+		}
 	}
 
 	if (IS_SD(mci))
diff --git a/drivers/mci/mci_spi.c b/drivers/mci/mci_spi.c
new file mode 100644
index 0000000..663db89
--- /dev/null
+++ b/drivers/mci/mci_spi.c
@@ -0,0 +1,431 @@
+/*
+ * (C) Copyright 2011 - Franck JULLIEN <elec4fun@gmail.com>
+ *
+ * This code was inspired from u-boot mmc_spi.c:
+ * Copyright (C) 2010 Thomas Chou <thomas@wytron.com.tw>
+ *
+ * and linux mmc_spi.c:
+ * (C) Copyright 2005, Intec Automation,
+ *              Mike Lavender (mike@steroidmicros)
+ * (C) Copyright 2006-2007, David Brownell
+ * (C) Copyright 2007, Axis Communications,
+ *              Hans-Peter Nilsson (hp@axis.com)
+ * (C) Copyright 2007, ATRON electronic GmbH,
+ *              Jan Nikitenko <jan.nikitenko@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ */
+
+#include <common.h>
+#include <init.h>
+#include <errno.h>
+#include <clock.h>
+#include <asm/io.h>
+#include <driver.h>
+#include <spi/spi.h>
+#include <mci.h>
+#include <crc.h>
+#ifdef CONFIG_MMC_SPI_CRC_ON
+#include <crc7.h>
+#endif
+
+#define to_spi_host(mci) container_of(mci, struct mmc_spi_host, mci)
+#define spi_setup(spi) spi->master->setup(spi)
+
+/* Response tokens used to ack each block written: */
+#define SPI_MMC_RESPONSE_CODE(x)	((x) & 0x1f)
+#define SPI_RESPONSE_ACCEPTED		((2 << 1)|1)
+
+/* Read and write blocks start with these tokens and end with crc;
+ * on error, read tokens act like a subset of R2_SPI_* values.
+ */
+#define SPI_TOKEN_SINGLE	0xFE	/* single block r/w, multiblock read */
+#define SPI_TOKEN_MULTI_WRITE	0xFC	/* multiblock write */
+#define SPI_TOKEN_STOP_TRAN	0xFD	/* terminate multiblock write */
+
+/* MMC SPI commands start with a start bit "0" and a transmit bit "1" */
+#define MMC_SPI_CMD(x) (0x40 | (x & 0x3F))
+
+#define MMC_SPI_BLOCKSIZE       512
+
+/* timeout value */
+#define CTOUT 8
+#define RTOUT 3000000 /* 1 sec */
+#define WTOUT 3000000 /* 1 sec */
+
+#ifndef CONFIG_MMC_SPI_CRC_ON
+/* Note that while the CRC, in general, is ignored in SPI mode, the very first
+command must be followed by a valid CRC, since the card is not yet in SPI mode.
+The CRC byte for a CMD0 command with a zero argument is a constant 0x95. For
+simplicity, this CRC byte is always sent with every command. */
+
+static inline u8 crc7(u8 crc, const u8 *buffer, size_t len)
+{
+	return 0x4A;
+}
+#endif
+
+struct mmc_spi_host {
+	struct mci_host	mci;
+	struct spi_device	*spi;
+	struct device_d	*dev;
+
+	/* for bulk data transfers */
+	struct spi_transfer	t_tx;
+	struct spi_message	m_tx;
+
+	/* for status readback */
+	struct spi_transfer	t_rx;
+	struct spi_message	m_rx;
+
+	void			*ones;
+};
+
+static char *maptype(struct mci_cmd *cmd)
+{
+	switch (cmd->resp_type) {
+	case MMC_RSP_NONE:	return "NONE";
+	case MMC_RSP_R1:	return "R1";
+	case MMC_RSP_R1b:	return "R1B";
+	case MMC_RSP_R2:	return "R2/R5";
+	case MMC_RSP_R3:	return "R3/R4/R7";
+	default:		return "?";
+	}
+}
+
+static inline int mmc_cs_off(struct mmc_spi_host *host)
+{
+	/* chipselect will always be inactive after setup() */
+	return spi_setup(host->spi);
+}
+
+static int
+mmc_spi_readbytes(struct mmc_spi_host *host, unsigned len, void *data)
+{
+	int status;
+
+	host->t_rx.len = len;
+	host->t_rx.rx_buf = data;
+
+	status = spi_sync(host->spi, &host->m_rx);
+
+	return status;
+}
+
+static int
+mmc_spi_writebytes(struct mmc_spi_host *host, unsigned len, void *data)
+{
+	int status;
+
+	host->t_tx.len = len;
+	host->t_tx.tx_buf = data;
+
+	status = spi_sync(host->spi, &host->m_tx);
+
+	return status;
+}
+
+static int mmc_spi_command_send(struct mmc_spi_host *host, struct mci_cmd *cmd)
+{
+	uint8_t r1;
+	uint8_t command[7];
+	int i;
+
+	command[0] = 0xff;
+	command[1] = MMC_SPI_CMD(cmd->cmdidx);
+	command[2] = cmd->cmdarg >> 24;
+	command[3] = cmd->cmdarg >> 16;
+	command[4] = cmd->cmdarg >> 8;
+	command[5] = cmd->cmdarg;
+	command[6] = (crc7(0, &command[1], 5) << 1) | 0x01;
+
+	mmc_spi_writebytes(host, 7, command);
+
+	for (i = 0; i < CTOUT; i++) {
+		mmc_spi_readbytes(host, 1, &r1);
+		if (i && ((r1 & 0x80) == 0)) {  /* r1 response */
+			dev_dbg(host->dev, "%s: CMD%d, TRY %d, RESP %x\n", __func__, cmd->cmdidx, i, r1);
+			break;
+		}
+	}
+
+	return r1;
+}
+
+static uint mmc_spi_readdata(struct mmc_spi_host *host, void *xbuf,
+				uint32_t bcnt, uint32_t bsize)
+{
+	uint8_t *buf = xbuf;
+	uint8_t r1;
+	uint16_t crc;
+	int i;
+
+	while (bcnt--) {
+		for (i = 0; i < RTOUT; i++) {
+			mmc_spi_readbytes(host, 1, &r1);
+			if (r1 != 0xff) /* data token */
+				break;
+		}
+		if (r1 == SPI_TOKEN_SINGLE) {
+			mmc_spi_readbytes(host, bsize, buf);
+			mmc_spi_readbytes(host, 2, &crc);
+#ifdef CONFIG_MMC_SPI_CRC_ON
+			if (swab16(cyg_crc16(buf, bsize)) != crc) {
+				dev_dbg(host->dev, "%s: CRC error\n", __func__);
+				r1 = R1_SPI_COM_CRC;
+				break;
+			}
+#endif
+			r1 = 0;
+		} else {
+			r1 = R1_SPI_ERROR;
+			break;
+		}
+		buf += bsize;
+	}
+
+	return r1;
+}
+
+static uint mmc_spi_writedata(struct mmc_spi_host *host, const void *xbuf,
+			      uint32_t bcnt, uint32_t bsize, int multi)
+{
+	const uint8_t *buf = xbuf;
+	uint8_t r1;
+	uint16_t crc;
+	uint8_t tok[2];
+	int i;
+
+	tok[0] = 0xff;
+	tok[1] = multi ? SPI_TOKEN_MULTI_WRITE : SPI_TOKEN_SINGLE;
+
+	while (bcnt--) {
+#ifdef CONFIG_MMC_SPI_CRC_ON
+		crc = swab16(cyg_crc16((u8 *)buf, bsize));
+#endif
+		mmc_spi_writebytes(host, 2, tok);
+		mmc_spi_writebytes(host, bsize, (void *)buf);
+		mmc_spi_writebytes(host, 2, &crc);
+
+		for (i = 0; i < CTOUT; i++) {
+			mmc_spi_readbytes(host, 1, &r1);
+			if ((r1 & 0x11) == 0x01) /* response token */
+				break;
+		}
+
+		dev_dbg(host->dev,"%s   : TOKEN%d RESP 0x%X\n", __func__, i, r1);
+		if (SPI_MMC_RESPONSE_CODE(r1) == SPI_RESPONSE_ACCEPTED) {
+			for (i = 0; i < WTOUT; i++) { /* wait busy */
+				mmc_spi_readbytes(host, 1, &r1);
+				if (i && r1 == 0xff) {
+					r1 = 0;
+					break;
+				}
+			}
+			if (i == WTOUT) {
+				dev_dbg(host->dev, "%s: wtout %x\n", __func__, r1);
+				r1 = R1_SPI_ERROR;
+				break;
+			}
+		} else {
+			dev_dbg(host->dev, "%s: err %x\n", __func__, r1);
+			r1 = R1_SPI_COM_CRC;
+			break;
+		}
+		buf += bsize;
+	}
+
+	if (multi && bcnt == -1) { /* stop multi write */
+		tok[1] = SPI_TOKEN_STOP_TRAN;
+		mmc_spi_writebytes(host, 2, tok);
+		for (i = 0; i < WTOUT; i++) { /* wait busy */
+			mmc_spi_readbytes(host, 1, &r1);
+			if (i && r1 == 0xff) {
+				r1 = 0;
+				break;
+			}
+		}
+		if (i == WTOUT) {
+			dev_dbg(host->dev, "%s: wstop %x\n", __func__, r1);
+			r1 = R1_SPI_ERROR;
+		}
+	}
+return r1;
+}
+
+static int mmc_spi_request(struct mci_host *mci, struct mci_cmd *cmd, struct mci_data *data)
+{
+	struct mmc_spi_host	*host = to_spi_host(mci);
+	uint8_t r1;
+	int i;
+	int ret = 0;
+
+	dev_dbg(host->dev, "%s     : CMD%02d, RESP %s, ARG 0x%X\n", __func__,
+	      cmd->cmdidx, maptype(cmd), cmd->cmdarg);
+
+	r1 = mmc_spi_command_send(host, cmd);
+
+	cmd->response[0] = r1;
+
+	if (r1 == 0xff) { /* no response */
+		ret = -ETIME;
+		goto done;
+	} else if (r1 & R1_SPI_COM_CRC) {
+		ret = -ECOMM;
+		goto done;
+	} else if (r1 & ~R1_SPI_IDLE) { /* other errors */
+		ret = -ETIME;
+		goto done;
+	} else if (cmd->resp_type == MMC_RSP_R2) {
+		r1 = mmc_spi_readdata(host, cmd->response, 1, 16);
+		for (i = 0; i < 4; i++)
+			cmd->response[i] = swab32(cmd->response[i]);
+		dev_dbg(host->dev, "MMC_RSP_R2 -> %x %x %x %x\n", cmd->response[0], cmd->response[1],
+		      cmd->response[2], cmd->response[3]);
+	} else if (!data) {
+		switch (cmd->cmdidx) {
+		case SD_CMD_SEND_IF_COND:
+		case MMC_CMD_SPI_READ_OCR:
+			mmc_spi_readbytes(host, 4, cmd->response);
+			cmd->response[0] = swab32(cmd->response[0]);
+			break;
+		}
+	} else {
+		if (data->flags == MMC_DATA_READ) {
+			dev_dbg(host->dev, "%s     : DATA READ, %x blocks, bsize = 0x%X\n", __func__,
+			      data->blocks, data->blocksize);
+			r1 = mmc_spi_readdata(host, data->dest,
+				data->blocks, data->blocksize);
+		} else if  (data->flags == MMC_DATA_WRITE) {
+			dev_dbg(host->dev, "%s     : DATA WRITE, %x blocks, bsize = 0x%X\n", __func__,
+			      data->blocks, data->blocksize);
+			r1 = mmc_spi_writedata(host, data->src,
+				data->blocks, data->blocksize,
+				(cmd->cmdidx == MMC_CMD_WRITE_MULTIPLE_BLOCK));
+		}
+		if (r1 & R1_SPI_COM_CRC)
+			ret = -ECOMM;
+		else if (r1) 
+			ret = -ETIME;
+	}
+
+done:
+	mmc_cs_off(host);
+	return ret;
+
+return  0;
+
+}
+
+static void mmc_spi_set_ios(struct mci_host *mci, struct device_d *mci_dev,
+			unsigned bus_width, unsigned clock)
+{
+	struct mmc_spi_host	*host = to_spi_host(mci);
+
+	spi_setup(host->spi);
+}
+
+static int mmc_spi_init(struct mci_host *mci, struct device_d *mci_dev)
+{
+	struct mmc_spi_host	*host = to_spi_host(mci);
+	mmc_spi_readbytes(host, 10, NULL);
+
+	/*
+	 * Do a burst with chipselect active-high.  We need to do this to
+	 * meet the requirement of 74 clock cycles with both chipselect
+	 * and CMD (MOSI) high before CMD0 ... after the card has been
+	 * powered up to Vdd(min), and so is ready to take commands.
+	 *
+	 * Some cards are particularly needy of this (e.g. Viking "SD256")
+	 * while most others don't seem to care.
+	 *
+	 * Note that this is one of the places MMC/SD plays games with the
+	 * SPI protocol.  Another is that when chipselect is released while
+	 * the card returns BUSY status, the clock must issue several cycles
+	 * with chipselect high before the card will stop driving its output.
+	 */
+
+	host->spi->mode |= SPI_CS_HIGH;
+	if (spi_setup(host->spi) != 0) {
+		/* Just warn; most cards work without it. */
+		dev_warn(&host->spi->dev,
+				"can't change chip-select polarity\n");
+		host->spi->mode &= ~SPI_CS_HIGH;
+	} else {
+		mmc_spi_readbytes(host, 18, NULL);
+
+		host->spi->mode &= ~SPI_CS_HIGH;
+		if (spi_setup(host->spi) != 0) {
+			/* Wot, we can't get the same setup we had before? */
+			dev_err(&host->spi->dev,
+					"can't restore chip-select polarity\n");
+		}
+	}
+
+	return 0;
+}
+
+static int spi_mci_probe(struct device_d *dev)
+{
+	struct spi_device	*spi = (struct spi_device *)dev->type_data;
+	struct mmc_spi_host	*host;
+	void			*ones;
+
+	host = xzalloc(sizeof(*host));
+	host->mci.send_cmd = mmc_spi_request;
+	host->mci.set_ios = mmc_spi_set_ios;
+	host->mci.init = mmc_spi_init;
+
+	host->dev = dev;
+	host->spi = spi;
+	dev->priv = host;
+
+	ones = xmalloc(MMC_SPI_BLOCKSIZE);
+	memset(ones, 0xff, MMC_SPI_BLOCKSIZE);
+
+	host->ones = ones;
+
+	spi_message_init(&host->m_tx);
+	spi_message_init(&host->m_rx);
+
+	spi_message_add_tail(&host->t_tx, &host->m_tx);
+	spi_message_add_tail(&host->t_rx, &host->m_rx);
+
+	host->t_rx.tx_buf = host->ones;
+	host->t_rx.cs_change = 1;
+
+	host->t_tx.cs_change = 1;
+
+	host->mci.voltages = MMC_VDD_32_33 | MMC_VDD_33_34;
+	host->mci.host_caps = MMC_CAP_SPI;
+
+	mci_register(&host->mci);
+
+	return 0;
+}
+
+static struct driver_d spi_mci_driver = {
+	.name	= "spi_mci",
+	.probe	= spi_mci_probe,
+};
+
+static int spi_mci_init_driver(void)
+{
+	register_driver(&spi_mci_driver);
+	return 0;
+}
+
+device_initcall(spi_mci_init_driver);
diff --git a/include/mci.h b/include/mci.h
index 69cffe8..ed54e14 100644
--- a/include/mci.h
+++ b/include/mci.h
@@ -49,6 +49,7 @@
 
 #define MMC_MODE_HS		0x001
 #define MMC_MODE_HS_52MHz	0x010
+#define MMC_CAP_SPI		0x020
 #define MMC_MODE_4BIT		0x100
 #define MMC_MODE_8BIT		0x200
 
@@ -56,6 +57,8 @@
 
 #define IS_SD(x) (x->version & SD_VERSION_SD)
 
+#define mmc_host_is_spi(host)	((host)->host_caps & MMC_CAP_SPI)
+
 #define MMC_DATA_READ		1
 #define MMC_DATA_WRITE		2
 
@@ -78,6 +81,8 @@
 #define MMC_CMD_WRITE_SINGLE_BLOCK	24
 #define MMC_CMD_WRITE_MULTIPLE_BLOCK	25
 #define MMC_CMD_APP_CMD			55
+#define MMC_CMD_SPI_READ_OCR		58
+#define MMC_CMD_SPI_CRC_ON_OFF		59
 
 #define SD_CMD_SEND_RELATIVE_ADDR	3
 #define SD_CMD_SWITCH_FUNC		6
@@ -155,6 +160,15 @@
 #define R1_ILLEGAL_COMMAND		(1 << 22)
 #define R1_APP_CMD			(1 << 5)
 
+#define R1_SPI_IDLE		(1 << 0)
+#define R1_SPI_ERASE_RESET	(1 << 1)
+#define R1_SPI_ILLEGAL_COMMAND	(1 << 2)
+#define R1_SPI_COM_CRC		(1 << 3)
+#define R1_SPI_ERASE_SEQ	(1 << 4)
+#define R1_SPI_ADDRESS		(1 << 5)
+#define R1_SPI_PARAMETER	(1 << 6)
+#define R1_SPI_ERROR		(1 << 7)
+
 /* response types */
 #define MMC_RSP_PRESENT (1 << 0)
 #define MMC_RSP_136     (1 << 1)                /* 136 bit response */
-- 
1.7.7


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

  parent reply	other threads:[~2011-11-23 21:12 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2011-11-23 21:12 [PATCH 0/4] " franck.jullien
2011-11-23 21:12 ` [PATCH 1/4] crypto: Add crc7 function franck.jullien
2011-11-23 21:12 ` franck.jullien [this message]
2011-11-24  9:17   ` [PATCH 2/4] mci: Add MCI over SPI support Sascha Hauer
2011-11-23 21:12 ` [PATCH 3/4] nios2: Include asm/unaligned.h franck.jullien
2011-11-24  9:36   ` Sascha Hauer
2011-11-23 21:12 ` [PATCH 4/4] spi/altera_spi: Add cs_change support franck.jullien

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1322082748-17409-3-git-send-email-franck.jullien@gmail.com \
    --to=franck.jullien@gmail.com \
    --cc=barebox@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox