mail archive of the barebox mailing list
 help / color / mirror / Atom feed
From: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
To: barebox@lists.infradead.org
Subject: [PATCH 1/2] at91sam9260/9g20ek: add dfu and usb serial support
Date: Thu,  5 Jan 2012 14:36:37 +0100	[thread overview]
Message-ID: <1325770598-10931-1-git-send-email-plagnioj@jcrosoft.com> (raw)

if bp3 is pressed 5s during boot enable dfu otherwise usbserial

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
 arch/arm/boards/at91sam9260ek/env/bin/init_board |   72 +++++++++++++++-------
 arch/arm/boards/at91sam9260ek/init.c             |    2 +
 arch/arm/configs/at91sam9260ek_defconfig         |   15 ++++-
 arch/arm/configs/at91sam9g20ek_defconfig         |   15 ++++-
 4 files changed, 79 insertions(+), 25 deletions(-)
 rewrite arch/arm/boards/at91sam9260ek/env/bin/init_board (67%)

diff --git a/arch/arm/boards/at91sam9260ek/env/bin/init_board b/arch/arm/boards/at91sam9260ek/env/bin/init_board
dissimilarity index 67%
index 0da2781..0a6baf7 100644
--- a/arch/arm/boards/at91sam9260ek/env/bin/init_board
+++ b/arch/arm/boards/at91sam9260ek/env/bin/init_board
@@ -1,23 +1,49 @@
-#!/bin/sh
-
-#PIOA_31
-gpio_get_value 63
-if [ $? != 0 ]
-then
-	exit
-fi
-
-echo "BP4 pressed detected wait 5s"
-timeout -s -a 5
-gpio_get_value 63
-if [ $? != 0 ]
-then
-	echo "BP4 released, normal boot"
-	exit
-fi
-
-echo ""
-echo "Start DFU Mode"
-echo ""
-
-dfu /dev/self0(barebox)sr,/dev/nand0.kernel.bb(kernel)r,/dev/nand0.root.bb(root)r -P 0x1234 -V 0x4321
+#!/bin/sh
+
+button_name="dfu_bp"
+button_wait=5
+
+product_id=0x1234
+vendor_id=0x4321
+
+dfu_config="/dev/nand0.barebox.bb(barebox)sr,/dev/nand0.kernel.bb(kernel)r,/dev/nand0.rootfs.bb(rootfs)r"
+
+if [ $at91_udc0.vbus != 1 ]
+then
+	echo "No USB Device cable plugged, normal boot"
+	exit
+fi
+
+gpio_get_value ${dfu_button}
+if [ $? != 0 ]
+then
+	autoboot_timeout=16
+	echo "enable tty over USB Device, increase the boot delay to ${autoboot_timeout}s"
+	usbserial
+	exit
+fi
+
+echo "${button_name} pressed detected wait ${button_wait}s"
+timeout -s -a ${button_wait}
+
+if [ $at91_udc0.vbus != 1 ]
+then
+	echo "No USB Device cable plugged, normal boot"
+	exit
+fi
+
+gpio_get_value ${dfu_button}
+if [ $? != 0 ]
+then
+	echo "${button_name} released, normal boot"
+	autoboot_timeout=16
+	echo "enable tty over USB Device, increase the boot delay to ${autoboot_timeout}s"
+	usbserial
+	exit
+fi
+
+echo ""
+echo "Start DFU Mode"
+echo ""
+
+dfu ${dfu_config} -P ${product_id} -V ${vendor_id}
diff --git a/arch/arm/boards/at91sam9260ek/init.c b/arch/arm/boards/at91sam9260ek/init.c
index b10d0dc..a11998a 100644
--- a/arch/arm/boards/at91sam9260ek/init.c
+++ b/arch/arm/boards/at91sam9260ek/init.c
@@ -212,8 +212,10 @@ static void __init ek_add_device_buttons(void)
 {
 	at91_set_gpio_input(AT91_PIN_PA30, 1);	/* btn3 */
 	at91_set_deglitch(AT91_PIN_PA30, 1);
+	export_env_ull("dfu_button", AT91_PIN_PA30);
 	at91_set_gpio_input(AT91_PIN_PA31, 1);	/* btn4 */
 	at91_set_deglitch(AT91_PIN_PA31, 1);
+	export_env_ull("btn4", AT91_PIN_PA31);
 }
 
 static int at91sam9260ek_devices_init(void)
diff --git a/arch/arm/configs/at91sam9260ek_defconfig b/arch/arm/configs/at91sam9260ek_defconfig
index 3367cee..f6d0f25 100644
--- a/arch/arm/configs/at91sam9260ek_defconfig
+++ b/arch/arm/configs/at91sam9260ek_defconfig
@@ -1,6 +1,8 @@
 CONFIG_ARCH_AT91SAM9260=y
 CONFIG_AEABI=y
+# CONFIG_CMD_ARM_CPUINFO is not set
 CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y
+CONFIG_EXPERIMENTAL=y
 CONFIG_PROMPT="9260-EK:"
 CONFIG_LONGHELP=y
 CONFIG_GLOB=y
@@ -8,6 +10,8 @@ CONFIG_PROMPT_HUSH_PS2="y"
 CONFIG_HUSH_FANCY_PROMPT=y
 CONFIG_CMDLINE_EDITING=y
 CONFIG_AUTO_COMPLETE=y
+# CONFIG_CONSOLE_ACTIVATE_FIRST is not set
+CONFIG_CONSOLE_ACTIVATE_ALL=y
 CONFIG_DEFAULT_ENVIRONMENT_GENERIC=y
 CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/at91sam9260ek/env"
 CONFIG_CMD_EDIT=y
@@ -24,6 +28,11 @@ CONFIG_CMD_MTEST=y
 CONFIG_CMD_MTEST_ALTERNATIVE=y
 CONFIG_CMD_FLASH=y
 CONFIG_CMD_BOOTM_SHOW_TYPE=y
+CONFIG_CMD_BOOTM_INITRD=y
+CONFIG_CMD_BOOTM_OFTREE=y
+CONFIG_CMD_BOOTM_OFTREE_UIMAGE=y
+CONFIG_CMD_UIMAGE=y
+# CONFIG_CMD_BOOTU is not set
 CONFIG_CMD_RESET=y
 CONFIG_CMD_GO=y
 CONFIG_CMD_OFTREE=y
@@ -40,9 +49,14 @@ CONFIG_DRIVER_NET_MACB=y
 # CONFIG_SPI is not set
 CONFIG_MTD=y
 CONFIG_NAND=y
+# CONFIG_NAND_ECC_HW is not set
+# CONFIG_NAND_ECC_HW_SYNDROME is not set
+# CONFIG_NAND_ECC_HW_NONE is not set
 CONFIG_NAND_ATMEL=y
 CONFIG_UBI=y
 CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_DFU=y
+CONFIG_USB_GADGET_SERIAL=y
 CONFIG_MCI=y
 CONFIG_MCI_STARTUP=y
 CONFIG_MCI_ATMEL=y
@@ -50,4 +64,3 @@ CONFIG_FS_FAT=y
 CONFIG_FS_FAT_WRITE=y
 CONFIG_FS_FAT_LFN=y
 CONFIG_ZLIB=y
-CONFIG_BZLIB=y
diff --git a/arch/arm/configs/at91sam9g20ek_defconfig b/arch/arm/configs/at91sam9g20ek_defconfig
index 2492b30..16b6252 100644
--- a/arch/arm/configs/at91sam9g20ek_defconfig
+++ b/arch/arm/configs/at91sam9g20ek_defconfig
@@ -1,7 +1,9 @@
 CONFIG_ARCH_AT91SAM9G20=y
 CONFIG_AT91_HAVE_2MMC=y
 CONFIG_AEABI=y
+# CONFIG_CMD_ARM_CPUINFO is not set
 CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y
+CONFIG_EXPERIMENTAL=y
 CONFIG_PROMPT="9G20-EK:"
 CONFIG_LONGHELP=y
 CONFIG_GLOB=y
@@ -9,6 +11,8 @@ CONFIG_PROMPT_HUSH_PS2="y"
 CONFIG_HUSH_FANCY_PROMPT=y
 CONFIG_CMDLINE_EDITING=y
 CONFIG_AUTO_COMPLETE=y
+# CONFIG_CONSOLE_ACTIVATE_FIRST is not set
+CONFIG_CONSOLE_ACTIVATE_ALL=y
 CONFIG_DEFAULT_ENVIRONMENT_GENERIC=y
 CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/at91sam9260ek/env"
 CONFIG_CMD_EDIT=y
@@ -25,6 +29,11 @@ CONFIG_CMD_MTEST=y
 CONFIG_CMD_MTEST_ALTERNATIVE=y
 CONFIG_CMD_FLASH=y
 CONFIG_CMD_BOOTM_SHOW_TYPE=y
+CONFIG_CMD_BOOTM_INITRD=y
+CONFIG_CMD_BOOTM_OFTREE=y
+CONFIG_CMD_BOOTM_OFTREE_UIMAGE=y
+CONFIG_CMD_UIMAGE=y
+# CONFIG_CMD_BOOTU is not set
 CONFIG_CMD_RESET=y
 CONFIG_CMD_GO=y
 CONFIG_CMD_OFTREE=y
@@ -41,9 +50,14 @@ CONFIG_DRIVER_NET_MACB=y
 # CONFIG_SPI is not set
 CONFIG_MTD=y
 CONFIG_NAND=y
+# CONFIG_NAND_ECC_HW is not set
+# CONFIG_NAND_ECC_HW_SYNDROME is not set
+# CONFIG_NAND_ECC_HW_NONE is not set
 CONFIG_NAND_ATMEL=y
 CONFIG_UBI=y
 CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_DFU=y
+CONFIG_USB_GADGET_SERIAL=y
 CONFIG_MCI=y
 CONFIG_MCI_STARTUP=y
 CONFIG_MCI_ATMEL=y
@@ -51,4 +65,3 @@ CONFIG_FS_FAT=y
 CONFIG_FS_FAT_WRITE=y
 CONFIG_FS_FAT_LFN=y
 CONFIG_ZLIB=y
-CONFIG_BZLIB=y
-- 
1.7.7


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

             reply	other threads:[~2012-01-05 13:43 UTC|newest]

Thread overview: 2+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2012-01-05 13:36 Jean-Christophe PLAGNIOL-VILLARD [this message]
2012-01-05 13:36 ` [PATCH 2/2] at91sam9260/9g20ek: add led support Jean-Christophe PLAGNIOL-VILLARD

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1325770598-10931-1-git-send-email-plagnioj@jcrosoft.com \
    --to=plagnioj@jcrosoft.com \
    --cc=barebox@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox