* [PATCH 01/10] ARM: add support of in_be16/32 and out_be16/32
2012-04-23 6:56 [PATCH 00/10] IXP4xx rebase WIP Jean-Christophe PLAGNIOL-VILLARD
@ 2012-04-23 7:02 ` Jean-Christophe PLAGNIOL-VILLARD
2012-04-23 7:02 ` [PATCH 02/10] ARM: Add support for IXP4xx CPU Jean-Christophe PLAGNIOL-VILLARD
` (9 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-04-23 7:02 UTC (permalink / raw)
To: barebox
This will allow to have cfi flash on big endian SoC as IXP4xx.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
arch/arm/include/asm/io.h | 5 +++++
1 files changed, 5 insertions(+), 0 deletions(-)
diff --git a/arch/arm/include/asm/io.h b/arch/arm/include/asm/io.h
index e0630eb..644378c 100644
--- a/arch/arm/include/asm/io.h
+++ b/arch/arm/include/asm/io.h
@@ -10,4 +10,9 @@ extern void memcpy_fromio(void *, const volatile void __iomem *, size_t);
extern void memcpy_toio(volatile void __iomem *, const void *, size_t);
extern void memset_io(volatile void __iomem *, int, size_t);
+#define in_be16(a) __be16_to_cpu(__raw_readw(a))
+#define in_be32(a) __be32_to_cpu(__raw_readl(a))
+#define out_be16(a, v) __raw_writew(__cpu_to_be16(v), a)
+#define out_be32(a, v) __raw_writel(__cpu_to_be32(v), a)
+
#endif /* __ASM_ARM_IO_H */
--
1.7.9.1
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* [PATCH 02/10] ARM: Add support for IXP4xx CPU
2012-04-23 6:56 [PATCH 00/10] IXP4xx rebase WIP Jean-Christophe PLAGNIOL-VILLARD
2012-04-23 7:02 ` [PATCH 01/10] ARM: add support of in_be16/32 and out_be16/32 Jean-Christophe PLAGNIOL-VILLARD
@ 2012-04-23 7:02 ` Jean-Christophe PLAGNIOL-VILLARD
2012-04-23 7:02 ` [PATCH 03/10] ARM: Add support for IXP4xx Network Process Engine and queue Manager support Jean-Christophe PLAGNIOL-VILLARD
` (8 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-04-23 7:02 UTC (permalink / raw)
To: barebox; +Cc: Krzysztof Hałasa
From: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
arch/arm/Kconfig | 8 +
arch/arm/Makefile | 1 +
arch/arm/mach-ixp4xx/Kconfig | 8 +
arch/arm/mach-ixp4xx/Makefile | 4 +
arch/arm/mach-ixp4xx/devices.c | 60 ++++
arch/arm/mach-ixp4xx/include/mach/cpu.h | 70 +++++
arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h | 365 +++++++++++++++++++++++
arch/arm/mach-ixp4xx/include/mach/platform.h | 24 ++
arch/arm/mach-ixp4xx/lowlevel_init.S | 25 ++
arch/arm/mach-ixp4xx/reset.c | 15 +
arch/arm/mach-ixp4xx/timer.c | 42 +++
drivers/serial/serial_ns16550.c | 6 +-
drivers/serial/serial_ns16550.h | 2 +
13 files changed, 629 insertions(+), 1 deletions(-)
create mode 100644 arch/arm/mach-ixp4xx/Kconfig
create mode 100644 arch/arm/mach-ixp4xx/Makefile
create mode 100644 arch/arm/mach-ixp4xx/devices.c
create mode 100644 arch/arm/mach-ixp4xx/include/mach/cpu.h
create mode 100644 arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h
create mode 100644 arch/arm/mach-ixp4xx/include/mach/platform.h
create mode 100644 arch/arm/mach-ixp4xx/lowlevel_init.S
create mode 100644 arch/arm/mach-ixp4xx/reset.c
create mode 100644 arch/arm/mach-ixp4xx/timer.c
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 8a4e1a2..2cc3f2d 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -49,6 +49,13 @@ config ARCH_MXS
bool "Freescale i.MX23/28 (mxs) based"
select GENERIC_GPIO
+config ARCH_IXP4XX
+ bool "Intel IXP4xx-based"
+ select CPU_XSCALE
+ select ARCH_SUPPORTS_BIG_ENDIAN
+ select CPU_BIG_ENDIAN
+ select ARCH_HAS_LOWLEVEL_INIT
+
config ARCH_NETX
bool "Hilscher NetX based"
select CPU_ARM926T
@@ -84,6 +91,7 @@ source arch/arm/mach-at91/Kconfig
source arch/arm/mach-ep93xx/Kconfig
source arch/arm/mach-imx/Kconfig
source arch/arm/mach-mxs/Kconfig
+source arch/arm/mach-ixp4xx/Kconfig
source arch/arm/mach-netx/Kconfig
source arch/arm/mach-nomadik/Kconfig
source arch/arm/mach-omap/Kconfig
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index c6444bb..cc5223e 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -55,6 +55,7 @@ machine-$(CONFIG_ARCH_AT91) := at91
machine-$(CONFIG_ARCH_EP93XX) := ep93xx
machine-$(CONFIG_ARCH_IMX) := imx
machine-$(CONFIG_ARCH_MXS) := mxs
+machine-$(CONFIG_ARCH_IXP4XX) := ixp4xx
machine-$(CONFIG_ARCH_NOMADIK) := nomadik
machine-$(CONFIG_ARCH_NETX) := netx
machine-$(CONFIG_ARCH_OMAP) := omap
diff --git a/arch/arm/mach-ixp4xx/Kconfig b/arch/arm/mach-ixp4xx/Kconfig
new file mode 100644
index 0000000..65778ab
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -0,0 +1,8 @@
+if ARCH_IXP4XX
+
+choice
+ prompt "IXP4xx Board Type"
+
+endchoice
+
+endif
diff --git a/arch/arm/mach-ixp4xx/Makefile b/arch/arm/mach-ixp4xx/Makefile
new file mode 100644
index 0000000..6e57c91
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/Makefile
@@ -0,0 +1,4 @@
+obj-y += lowlevel_init.o
+obj-y += devices.o
+obj-y += timer.o
+obj-y += reset.o
diff --git a/arch/arm/mach-ixp4xx/devices.c b/arch/arm/mach-ixp4xx/devices.c
new file mode 100644
index 0000000..8a496d1
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/devices.c
@@ -0,0 +1,60 @@
+#include <common.h>
+#include <init.h>
+#include <ns16550.h>
+#include <asm/armlinux.h>
+#include <asm/io.h>
+#include <mach/ixp4xx-regs.h>
+
+#ifdef CONFIG_DRIVER_SERIAL_NS16550
+/**
+ * @brief UART port register read function for IXP4XX
+ *
+ * @param base base address of UART
+ * @param reg_idx register index
+ *
+ * @return character read from register
+ */
+static unsigned int ixp4xx_uart_read(unsigned long base, unsigned char reg_idx)
+{
+ return readb(reg_idx + REG_OFFSET + (uint8_t *)base);
+}
+
+/**
+ * @brief UART port register write function for IXP4XX
+ *
+ * @param val value to write
+ * @param base base address of UART
+ * @param reg_idx register index
+ *
+ * @return void
+ */
+static void ixp4xx_uart_write(unsigned int val, unsigned long base,
+ unsigned char reg_idx)
+{
+ writeb(val, reg_idx + REG_OFFSET + (uint8_t *)base);
+}
+
+static struct NS16550_plat serial_plat = {
+ .clock = 14745600,
+ .shift = 2,
+ .reg_read = ixp4xx_uart_read,
+ .reg_write = ixp4xx_uart_write,
+};
+
+/**
+ * @brief UART serial port initialization
+ *
+ * @return result of device registration
+ */
+struct device_d* ixp4xx_add_uart(int id, u32 base)
+{
+ /* Register the serial port */
+ return add_generic_device("serial_ns16550", id, NULL, base, 0xfff,
+ IORESOURCE_MEM, &serial_plat);
+}
+#else
+struct device_d* ixp4xx_add_uart(int id, u32 base)
+{
+ return NULL;
+}
+#endif /* CONFIG_DRIVER_SERIAL_NS16550 */
diff --git a/arch/arm/mach-ixp4xx/include/mach/cpu.h b/arch/arm/mach-ixp4xx/include/mach/cpu.h
new file mode 100644
index 0000000..3de021e
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/include/mach/cpu.h
@@ -0,0 +1,70 @@
+/*
+ * arch/arm/mach-ixp4xx/include/mach/cpu.h
+ *
+ * IXP4XX cpu type detection
+ *
+ * Copyright (C) 2007 MontaVista Software, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef __ASM_ARCH_CPU_H__
+#define __ASM_ARCH_CPU_H__
+
+#include <linux/types.h>
+
+/* Processor id value in CP15 Register 0 */
+#define IXP42X_PROCESSOR_ID_VALUE 0x690541c0 /* including unused 0x690541Ex */
+#define IXP42X_PROCESSOR_ID_MASK 0xffffffc0
+
+#define IXP43X_PROCESSOR_ID_VALUE 0x69054040
+#define IXP43X_PROCESSOR_ID_MASK 0xfffffff0
+
+#define IXP46X_PROCESSOR_ID_VALUE 0x69054200 /* including IXP455 */
+#define IXP46X_PROCESSOR_ID_MASK 0xfffffff0
+
+#define cpu_is_ixp42x_rev_a0() ((read_cpuid_id() & (IXP42X_PROCESSOR_ID_MASK | 0xF)) == \
+ IXP42X_PROCESSOR_ID_VALUE)
+#define cpu_is_ixp42x() ((read_cpuid_id() & IXP42X_PROCESSOR_ID_MASK) == \
+ IXP42X_PROCESSOR_ID_VALUE)
+#define cpu_is_ixp43x() ((read_cpuid_id() & IXP43X_PROCESSOR_ID_MASK) == \
+ IXP43X_PROCESSOR_ID_VALUE)
+#define cpu_is_ixp46x() ((read_cpuid_id() & IXP46X_PROCESSOR_ID_MASK) == \
+ IXP46X_PROCESSOR_ID_VALUE)
+
+/*
+ * The CPU ID never changes at run time, so we might as well tell the
+ * compiler that it's constant. Use this function to read the CPU ID
+ * rather than directly reading processor_id or read_cpuid() directly.
+ */
+static inline u32 __attribute_const__ read_cpuid_id(void)
+{
+ u32 val;
+ asm("mrc p15, 0, %0, c0, c0, 0" : "=r" (val) : : "cc");
+
+ return val;
+}
+
+static inline u32 ixp4xx_read_feature_bits(void)
+{
+ u32 val = ~IXP4XX_EXP_CFG2;
+
+ if (cpu_is_ixp42x_rev_a0())
+ return IXP42X_FEATURE_MASK & ~(IXP4XX_FEATURE_RCOMP |
+ IXP4XX_FEATURE_AES);
+ if (cpu_is_ixp42x())
+ return val & IXP42X_FEATURE_MASK;
+ if (cpu_is_ixp43x())
+ return val & IXP43X_FEATURE_MASK;
+ return val & IXP46X_FEATURE_MASK;
+}
+
+static inline void ixp4xx_write_feature_bits(u32 value)
+{
+ IXP4XX_EXP_CFG2 = ~value;
+}
+
+#endif /* _ASM_ARCH_CPU_H */
diff --git a/arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h b/arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h
new file mode 100644
index 0000000..da4dc8a
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h
@@ -0,0 +1,365 @@
+/*
+ * Register definitions for IXP4xx chipset.
+ *
+ * Copyright (C) 2002 Intel Corporation.
+ * Copyright (C) 2003-2004 MontaVista Software, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef _ASM_ARM_IXP4XX_H_
+#define _ASM_ARM_IXP4XX_H_
+
+#ifdef __ASSEMBLER__
+#define IXP4XX_REG(reg) (reg)
+#else
+#define IXP4XX_REG(reg) (*(volatile u32 *)(reg))
+#define IXP4XX_BASE(reg) ((u32*)(reg))
+#endif
+
+/* Expansion Bus region */
+
+/* Queue Manager */
+#define IXP4XX_QMGR_BASE (0x60000000)
+#define IXP4XX_QMGR_REGION_SIZE (0x00004000)
+
+
+/* PCI Config registers */
+#define IXP4XX_PCI_CFG_BASE (0xC0000000)
+#define IXP4XX_PCI_CFG_REGION_SIZE (0x00001000)
+
+/* Peripheral space */
+#define IXP4XX_PERIPHERAL_BASE (0xC8000000)
+#define IXP4XX_PERIPHERAL_REGION_SIZE (0x00013000)
+
+/*
+ * Debug UART
+ *
+ * This is basically a remap of UART1 into a region that is section
+ * aligned so that it can be used with the low-level debug code.
+ */
+#define IXP4XX_DEBUG_UART_BASE (0xC8000000)
+#define IXP4XX_DEBUG_UART_REGION_SIZE (0x00001000)
+
+/* Expansion Bus Controller registers. */
+#define IXP4XX_EXP_CS0 IXP4XX_REG(0xC4000000)
+#define IXP4XX_EXP_CS1 IXP4XX_REG(0xC4000004)
+#define IXP4XX_EXP_CS2 IXP4XX_REG(0xC4000008)
+#define IXP4XX_EXP_CS3 IXP4XX_REG(0xC400000C)
+#define IXP4XX_EXP_CS4 IXP4XX_REG(0xC4000010)
+#define IXP4XX_EXP_CS5 IXP4XX_REG(0xC4000014)
+#define IXP4XX_EXP_CS6 IXP4XX_REG(0xC4000018)
+#define IXP4XX_EXP_CS7 IXP4XX_REG(0xC400001C)
+
+#define IXP4XX_EXP_BASE(n) (0x50000000 + (n) * 1000000)
+
+#define IXP4XX_EXP_EN 0x80000000
+#define IXP4XX_EXP_T1(n) (0x10000000 * (n)) /* valid: 0 - 3 */
+#define IXP4XX_EXP_T2(n) (0x04000000 * (n)) /* valid: 0 - 3 */
+#define IXP4XX_EXP_T3(n) (0x00400000 * (n)) /* valid: 0 - 15 */
+#define IXP4XX_EXP_T4(n) (0x00100000 * (n)) /* valid: 0 - 3 */
+#define IXP4XX_EXP_T5(n) (0x00010000 * (n)) /* valid: 0 - 15 */
+#define IXP4XX_EXP_INTEL 0x00000000
+#define IXP4XX_EXP_MOTO 0x00004000
+#define IXP4XX_EXP_HPI 0x00008000
+#define IXP4XX_EXP_BITS(n) (0x00000400 * ((n) - 9)) /* valid: 9 - 24 */
+#define IXP4XX_EXP_BYTE_RD16 0x00000040
+#define IXP4XX_EXP_HRDY_POL 0x00000020
+#define IXP4XX_EXP_MUX_EN 0x00000010
+#define IXP4XX_EXP_SPLT_EN 0x00000008
+#define IXP4XX_EXP_WR_EN 0x00000002
+#define IXP4XX_EXP_BYTE_EN 0x00000001
+
+#define IXP4XX_EXP_CFG0 IXP4XX_REG(0xC4000020)
+#define IXP4XX_EXP_CFG1 IXP4XX_REG(0xC4000024)
+#define IXP4XX_EXP_CFG2 IXP4XX_REG(0xC4000028)
+#define IXP4XX_EXP_CFG3 IXP4XX_REG(0xC400002C)
+
+
+/* Peripheral Space Register Region Base Addresses */
+#define IXP4XX_UART1_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0x0000)
+#define IXP4XX_UART2_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0x1000)
+#define IXP4XX_PMU_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0x2000)
+#define IXP4XX_INTC_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0x3000)
+#define IXP4XX_GPIO_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0x4000)
+#define IXP4XX_NPEA_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0x6000)
+#define IXP4XX_NPEB_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0x7000)
+#define IXP4XX_NPEC_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0x8000)
+#define IXP4XX_EthB_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0x9000)
+#define IXP4XX_EthC_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0xA000)
+#define IXP4XX_USB_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0xB000)
+/* IXP46x only */
+#define IXP4XX_EthA_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0xC000)
+#define IXP4XX_EthB1_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0xD000)
+#define IXP4XX_EthB2_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0xE000)
+#define IXP4XX_EthB3_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0xF000)
+#define IXP4XX_TIMESYNC_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0x10000)
+#define IXP4XX_I2C_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0x11000)
+#define IXP4XX_SSP_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0x12000)
+
+/*
+ Constants to make it easy to access Interrupt Controller registers
+ */
+#define IXP4XX_ICPR_OFFSET 0x00 /* Interrupt Status */
+#define IXP4XX_ICMR_OFFSET 0x04 /* Interrupt Enable */
+#define IXP4XX_ICLR_OFFSET 0x08 /* Interrupt IRQ/FIQ Select */
+#define IXP4XX_ICIP_OFFSET 0x0C /* IRQ Status */
+#define IXP4XX_ICFP_OFFSET 0x10 /* FIQ Status */
+#define IXP4XX_ICHR_OFFSET 0x14 /* Interrupt Priority */
+#define IXP4XX_ICIH_OFFSET 0x18 /* IRQ Highest Pri Int */
+#define IXP4XX_ICFH_OFFSET 0x1C /* FIQ Highest Pri Int */
+
+/* IXP465-only */
+#define IXP4XX_ICPR2_OFFSET 0x20 /* Interrupt Status 2 */
+#define IXP4XX_ICMR2_OFFSET 0x24 /* Interrupt Enable 2 */
+#define IXP4XX_ICLR2_OFFSET 0x28 /* Interrupt IRQ/FIQ Select 2 */
+#define IXP4XX_ICIP2_OFFSET 0x2C /* IRQ Status */
+#define IXP4XX_ICFP2_OFFSET 0x30 /* FIQ Status */
+#define IXP4XX_ICEEN_OFFSET 0x34 /* Error High Pri Enable */
+
+
+/* Interrupt Controller Register Definitions. */
+#define IXP4XX_INTC_REG(x) ((volatile u32 *)(IXP4XX_INTC_BASE + (x)))
+
+#define IXP4XX_ICPR IXP4XX_INTC_REG(IXP4XX_ICPR_OFFSET)
+#define IXP4XX_ICMR IXP4XX_INTC_REG(IXP4XX_ICMR_OFFSET)
+#define IXP4XX_ICLR IXP4XX_INTC_REG(IXP4XX_ICLR_OFFSET)
+#define IXP4XX_ICIP IXP4XX_INTC_REG(IXP4XX_ICIP_OFFSET)
+#define IXP4XX_ICFP IXP4XX_INTC_REG(IXP4XX_ICFP_OFFSET)
+#define IXP4XX_ICHR IXP4XX_INTC_REG(IXP4XX_ICHR_OFFSET)
+#define IXP4XX_ICIH IXP4XX_INTC_REG(IXP4XX_ICIH_OFFSET)
+#define IXP4XX_ICFH IXP4XX_INTC_REG(IXP4XX_ICFH_OFFSET)
+#define IXP4XX_ICPR2 IXP4XX_INTC_REG(IXP4XX_ICPR2_OFFSET)
+#define IXP4XX_ICMR2 IXP4XX_INTC_REG(IXP4XX_ICMR2_OFFSET)
+#define IXP4XX_ICLR2 IXP4XX_INTC_REG(IXP4XX_ICLR2_OFFSET)
+#define IXP4XX_ICIP2 IXP4XX_INTC_REG(IXP4XX_ICIP2_OFFSET)
+#define IXP4XX_ICFP2 IXP4XX_INTC_REG(IXP4XX_ICFP2_OFFSET)
+#define IXP4XX_ICEEN IXP4XX_INTC_REG(IXP4XX_ICEEN_OFFSET)
+
+/* Constants to make it easy to access GPIO registers */
+#define IXP4XX_GPIO_GPOUTR_OFFSET 0x00
+#define IXP4XX_GPIO_GPOER_OFFSET 0x04
+#define IXP4XX_GPIO_GPINR_OFFSET 0x08
+#define IXP4XX_GPIO_GPISR_OFFSET 0x0C
+#define IXP4XX_GPIO_GPIT1R_OFFSET 0x10
+#define IXP4XX_GPIO_GPIT2R_OFFSET 0x14
+#define IXP4XX_GPIO_GPCLKR_OFFSET 0x18
+#define IXP4XX_GPIO_GPDBSELR_OFFSET 0x1C
+
+/* GPIO Register Definitions - perform only 32-bit reads/writes */
+#define IXP4XX_GPIO_REG(x) ((volatile u32 *)(IXP4XX_GPIO_BASE + (x)))
+
+#define IXP4XX_GPIO_GPOUTR IXP4XX_GPIO_REG(IXP4XX_GPIO_GPOUTR_OFFSET)
+#define IXP4XX_GPIO_GPOER IXP4XX_GPIO_REG(IXP4XX_GPIO_GPOER_OFFSET)
+#define IXP4XX_GPIO_GPINR IXP4XX_GPIO_REG(IXP4XX_GPIO_GPINR_OFFSET)
+#define IXP4XX_GPIO_GPISR IXP4XX_GPIO_REG(IXP4XX_GPIO_GPISR_OFFSET)
+#define IXP4XX_GPIO_GPIT1R IXP4XX_GPIO_REG(IXP4XX_GPIO_GPIT1R_OFFSET)
+#define IXP4XX_GPIO_GPIT2R IXP4XX_GPIO_REG(IXP4XX_GPIO_GPIT2R_OFFSET)
+#define IXP4XX_GPIO_GPCLKR IXP4XX_GPIO_REG(IXP4XX_GPIO_GPCLKR_OFFSET)
+#define IXP4XX_GPIO_GPDBSELR IXP4XX_GPIO_REG(IXP4XX_GPIO_GPDBSELR_OFFSET)
+
+/* GPIO register bit definitions */
+
+/* Interrupt styles */
+#define IXP4XX_GPIO_STYLE_ACTIVE_HIGH 0x0
+#define IXP4XX_GPIO_STYLE_ACTIVE_LOW 0x1
+#define IXP4XX_GPIO_STYLE_RISING_EDGE 0x2
+#define IXP4XX_GPIO_STYLE_FALLING_EDGE 0x3
+#define IXP4XX_GPIO_STYLE_TRANSITIONAL 0x4
+
+/* Mask used to clear interrupt styles */
+#define IXP4XX_GPIO_STYLE_CLEAR 0x7
+#define IXP4XX_GPIO_STYLE_SIZE 3
+
+/* Operating System Timer Register Definitions. */
+#define IXP4XX_OSTS IXP4XX_REG(0xC8005000) /* Continious TimeStamp */
+#define IXP4XX_OST1 IXP4XX_REG(0xC8005004) /* Timer 1 Timestamp */
+#define IXP4XX_OSRT1 IXP4XX_REG(0xC8005008) /* Timer 1 Reload */
+#define IXP4XX_OST2 IXP4XX_REG(0xC800500C) /* Timer 2 Timestamp */
+#define IXP4XX_OSRT2 IXP4XX_REG(0xC8005010) /* Timer 2 Reload */
+#define IXP4XX_OSWT IXP4XX_REG(0xC8005014) /* Watchdog Timer */
+#define IXP4XX_OSWE IXP4XX_REG(0xC8005018) /* Watchdog Enable */
+#define IXP4XX_OSWK IXP4XX_REG(0xC800501C) /* Watchdog Key */
+#define IXP4XX_OSST IXP4XX_REG(0xC8005020) /* Timer Status */
+
+/* Timer register values and bit definitions */
+#define IXP4XX_OST_ENABLE 0x00000001
+#define IXP4XX_OST_ONE_SHOT 0x00000002
+/* Low order bits of reload value ignored */
+#define IXP4XX_OST_RELOAD_MASK 0x00000003
+#define IXP4XX_OST_DISABLED 0x00000000
+#define IXP4XX_OSST_TIMER_1_PEND 0x00000001
+#define IXP4XX_OSST_TIMER_2_PEND 0x00000002
+#define IXP4XX_OSST_TIMER_TS_PEND 0x00000004
+#define IXP4XX_OSST_TIMER_WDOG_PEND 0x00000008
+#define IXP4XX_OSST_TIMER_WARM_RESET 0x00000010
+
+#define IXP4XX_WDT_KEY 0x0000482E
+
+#define IXP4XX_WDT_RESET_ENABLE 0x00000001
+#define IXP4XX_WDT_IRQ_ENABLE 0x00000002
+#define IXP4XX_WDT_COUNT_ENABLE 0x00000004
+
+
+/* Constants to make it easy to access PCI Control/Status registers */
+#define PCI_NP_AD_OFFSET 0x00
+#define PCI_NP_CBE_OFFSET 0x04
+#define PCI_NP_WDATA_OFFSET 0x08
+#define PCI_NP_RDATA_OFFSET 0x0c
+#define PCI_CRP_AD_CBE_OFFSET 0x10
+#define PCI_CRP_WDATA_OFFSET 0x14
+#define PCI_CRP_RDATA_OFFSET 0x18
+#define PCI_CSR_OFFSET 0x1c
+#define PCI_ISR_OFFSET 0x20
+#define PCI_INTEN_OFFSET 0x24
+#define PCI_DMACTRL_OFFSET 0x28
+#define PCI_AHBMEMBASE_OFFSET 0x2c
+#define PCI_AHBIOBASE_OFFSET 0x30
+#define PCI_PCIMEMBASE_OFFSET 0x34
+#define PCI_AHBDOORBELL_OFFSET 0x38
+#define PCI_PCIDOORBELL_OFFSET 0x3C
+#define PCI_ATPDMA0_AHBADDR_OFFSET 0x40
+#define PCI_ATPDMA0_PCIADDR_OFFSET 0x44
+#define PCI_ATPDMA0_LENADDR_OFFSET 0x48
+#define PCI_ATPDMA1_AHBADDR_OFFSET 0x4C
+#define PCI_ATPDMA1_PCIADDR_OFFSET 0x50
+#define PCI_ATPDMA1_LENADDR_OFFSET 0x54
+
+/* PCI Control/Status Registers */
+#define IXP4XX_PCI_CSR(x) ((volatile u32 *)(IXP4XX_PCI_CFG_BASE + (x)))
+
+#define PCI_NP_AD IXP4XX_PCI_CSR(PCI_NP_AD_OFFSET)
+#define PCI_NP_CBE IXP4XX_PCI_CSR(PCI_NP_CBE_OFFSET)
+#define PCI_NP_WDATA IXP4XX_PCI_CSR(PCI_NP_WDATA_OFFSET)
+#define PCI_NP_RDATA IXP4XX_PCI_CSR(PCI_NP_RDATA_OFFSET)
+#define PCI_CRP_AD_CBE IXP4XX_PCI_CSR(PCI_CRP_AD_CBE_OFFSET)
+#define PCI_CRP_WDATA IXP4XX_PCI_CSR(PCI_CRP_WDATA_OFFSET)
+#define PCI_CRP_RDATA IXP4XX_PCI_CSR(PCI_CRP_RDATA_OFFSET)
+#define PCI_CSR IXP4XX_PCI_CSR(PCI_CSR_OFFSET)
+#define PCI_ISR IXP4XX_PCI_CSR(PCI_ISR_OFFSET)
+#define PCI_INTEN IXP4XX_PCI_CSR(PCI_INTEN_OFFSET)
+#define PCI_DMACTRL IXP4XX_PCI_CSR(PCI_DMACTRL_OFFSET)
+#define PCI_AHBMEMBASE IXP4XX_PCI_CSR(PCI_AHBMEMBASE_OFFSET)
+#define PCI_AHBIOBASE IXP4XX_PCI_CSR(PCI_AHBIOBASE_OFFSET)
+#define PCI_PCIMEMBASE IXP4XX_PCI_CSR(PCI_PCIMEMBASE_OFFSET)
+#define PCI_AHBDOORBELL IXP4XX_PCI_CSR(PCI_AHBDOORBELL_OFFSET)
+#define PCI_PCIDOORBELL IXP4XX_PCI_CSR(PCI_PCIDOORBELL_OFFSET)
+#define PCI_ATPDMA0_AHBADDR IXP4XX_PCI_CSR(PCI_ATPDMA0_AHBADDR_OFFSET)
+#define PCI_ATPDMA0_PCIADDR IXP4XX_PCI_CSR(PCI_ATPDMA0_PCIADDR_OFFSET)
+#define PCI_ATPDMA0_LENADDR IXP4XX_PCI_CSR(PCI_ATPDMA0_LENADDR_OFFSET)
+#define PCI_ATPDMA1_AHBADDR IXP4XX_PCI_CSR(PCI_ATPDMA1_AHBADDR_OFFSET)
+#define PCI_ATPDMA1_PCIADDR IXP4XX_PCI_CSR(PCI_ATPDMA1_PCIADDR_OFFSET)
+#define PCI_ATPDMA1_LENADDR IXP4XX_PCI_CSR(PCI_ATPDMA1_LENADDR_OFFSET)
+
+/* PCI register values and bit definitions */
+
+/* CSR bit definitions */
+#define PCI_CSR_HOST 0x00000001
+#define PCI_CSR_ARBEN 0x00000002
+#define PCI_CSR_ADS 0x00000004
+#define PCI_CSR_PDS 0x00000008
+#define PCI_CSR_ABE 0x00000010
+#define PCI_CSR_DBT 0x00000020
+#define PCI_CSR_ASE 0x00000100
+#define PCI_CSR_IC 0x00008000
+
+/* ISR (Interrupt status) Register bit definitions */
+#define PCI_ISR_PSE 0x00000001
+#define PCI_ISR_PFE 0x00000002
+#define PCI_ISR_PPE 0x00000004
+#define PCI_ISR_AHBE 0x00000008
+#define PCI_ISR_APDC 0x00000010
+#define PCI_ISR_PADC 0x00000020
+#define PCI_ISR_ADB 0x00000040
+#define PCI_ISR_PDB 0x00000080
+
+/* INTEN (Interrupt Enable) Register bit definitions */
+#define PCI_INTEN_PSE 0x00000001
+#define PCI_INTEN_PFE 0x00000002
+#define PCI_INTEN_PPE 0x00000004
+#define PCI_INTEN_AHBE 0x00000008
+#define PCI_INTEN_APDC 0x00000010
+#define PCI_INTEN_PADC 0x00000020
+#define PCI_INTEN_ADB 0x00000040
+#define PCI_INTEN_PDB 0x00000080
+
+/* Shift value for byte enable on NP cmd/byte enable register */
+#define IXP4XX_PCI_NP_CBE_BESL 4
+
+/* PCI commands supported by NP access unit */
+#define NP_CMD_IOREAD 0x2
+#define NP_CMD_IOWRITE 0x3
+#define NP_CMD_CONFIGREAD 0xA
+#define NP_CMD_CONFIGWRITE 0xB
+#define NP_CMD_MEMREAD 0x6
+#define NP_CMD_MEMWRITE 0x7
+
+/* Constants for CRP access into local config space */
+#define CRP_AD_CBE_BESL 20
+#define CRP_AD_CBE_WRITE 0x00010000
+
+/* USB Device Controller */
+# define IXP4XX_USB_REG(x) (*((volatile u32 *)(x)))
+
+/* SDRAM Controller registers. */
+#define IXP4XX_SDRAM_CONFIG IXP4XX_REG(0xCC000000)
+#define IXP4XX_SDRAM_REFRESH IXP4XX_REG(0xCC000004)
+#define IXP4XX_SDRAM_IR IXP4XX_REG(0xCC000008)
+
+/* "fuse" bits of IXP_EXP_CFG2 */
+/* All IXP4xx CPUs */
+#define IXP4XX_FEATURE_RCOMP (1 << 0)
+#define IXP4XX_FEATURE_USB_DEVICE (1 << 1)
+#define IXP4XX_FEATURE_HASH (1 << 2)
+#define IXP4XX_FEATURE_AES (1 << 3)
+#define IXP4XX_FEATURE_DES (1 << 4)
+#define IXP4XX_FEATURE_HDLC (1 << 5)
+#define IXP4XX_FEATURE_AAL (1 << 6)
+#define IXP4XX_FEATURE_HSS (1 << 7)
+#define IXP4XX_FEATURE_UTOPIA (1 << 8)
+#define IXP4XX_FEATURE_NPEB_ETH0 (1 << 9)
+#define IXP4XX_FEATURE_NPEC_ETH (1 << 10)
+#define IXP4XX_FEATURE_RESET_NPEA (1 << 11)
+#define IXP4XX_FEATURE_RESET_NPEB (1 << 12)
+#define IXP4XX_FEATURE_RESET_NPEC (1 << 13)
+#define IXP4XX_FEATURE_PCI (1 << 14)
+#define IXP4XX_FEATURE_UTOPIA_PHY_LIMIT (3 << 16)
+#define IXP4XX_FEATURE_XSCALE_MAX_FREQ (3 << 22)
+#define IXP42X_FEATURE_MASK (IXP4XX_FEATURE_RCOMP | \
+ IXP4XX_FEATURE_USB_DEVICE | \
+ IXP4XX_FEATURE_HASH | \
+ IXP4XX_FEATURE_AES | \
+ IXP4XX_FEATURE_DES | \
+ IXP4XX_FEATURE_HDLC | \
+ IXP4XX_FEATURE_AAL | \
+ IXP4XX_FEATURE_HSS | \
+ IXP4XX_FEATURE_UTOPIA | \
+ IXP4XX_FEATURE_NPEB_ETH0 | \
+ IXP4XX_FEATURE_NPEC_ETH | \
+ IXP4XX_FEATURE_RESET_NPEA | \
+ IXP4XX_FEATURE_RESET_NPEB | \
+ IXP4XX_FEATURE_RESET_NPEC | \
+ IXP4XX_FEATURE_PCI | \
+ IXP4XX_FEATURE_UTOPIA_PHY_LIMIT | \
+ IXP4XX_FEATURE_XSCALE_MAX_FREQ)
+
+/* IXP43x/46x CPUs */
+#define IXP4XX_FEATURE_ECC_TIMESYNC (1 << 15)
+#define IXP4XX_FEATURE_USB_HOST (1 << 18)
+#define IXP4XX_FEATURE_NPEA_ETH (1 << 19)
+#define IXP43X_FEATURE_MASK (IXP42X_FEATURE_MASK | \
+ IXP4XX_FEATURE_ECC_TIMESYNC | \
+ IXP4XX_FEATURE_USB_HOST | \
+ IXP4XX_FEATURE_NPEA_ETH)
+
+/* IXP46x CPU (including IXP455) only */
+#define IXP4XX_FEATURE_NPEB_ETH_1_TO_3 (1 << 20)
+#define IXP4XX_FEATURE_RSA (1 << 21)
+#define IXP46X_FEATURE_MASK (IXP43X_FEATURE_MASK | \
+ IXP4XX_FEATURE_NPEB_ETH_1_TO_3 | \
+ IXP4XX_FEATURE_RSA)
+
+#endif
diff --git a/arch/arm/mach-ixp4xx/include/mach/platform.h b/arch/arm/mach-ixp4xx/include/mach/platform.h
new file mode 100644
index 0000000..ae4b767
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/include/mach/platform.h
@@ -0,0 +1,24 @@
+#ifndef __MACH_PLATFORM__
+#define __MACH_PLATFORM__
+
+#include <asm/types.h>
+
+#ifndef __ARMEB__
+#define REG_OFFSET 0
+#else
+#define REG_OFFSET 3
+#endif
+
+struct device_d* ixp4xx_add_uart(int id, u32 base);
+
+static inline struct device_d* ixp4xx_add_uart1(void)
+{
+ return ixp4xx_add_uart(0, (u32)IXP4XX_UART1_BASE);
+}
+
+static inline struct device_d* ixp4xx_add_uart2(void)
+{
+ return ixp4xx_add_uart(1, (u32)IXP4XX_UART2_BASE);
+}
+
+#endif /* __MACH_PLATFORM__ */
diff --git a/arch/arm/mach-ixp4xx/lowlevel_init.S b/arch/arm/mach-ixp4xx/lowlevel_init.S
new file mode 100644
index 0000000..e5d4802
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/lowlevel_init.S
@@ -0,0 +1,25 @@
+#include <mach/ixp4xx-regs.h>
+
+ .section ".text_bare_init", "ax"
+
+ .globl arch_init_lowlevel
+arch_init_lowlevel:
+ ldr r0, cfg
+ ldr r1, [r0]
+ /*
+ * check if EXP bus already unmap from 0x0
+ * as example we run from ram
+ */
+ and r2, r1, #IXP4XX_EXP_EN
+ cmp r2, #0
+ beq 10f
+ bic r1, r1, #IXP4XX_EXP_EN /* unmap EXP bus from 0x0 */
+ str r1, [r0]
+
+ /* return to ROM */
+ orr lr, #0x50000000
+10:
+ mov pc, lr
+
+cfg:
+ .word IXP4XX_EXP_CFG0
diff --git a/arch/arm/mach-ixp4xx/reset.c b/arch/arm/mach-ixp4xx/reset.c
new file mode 100644
index 0000000..d0d3894
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/reset.c
@@ -0,0 +1,15 @@
+#include <common.h>
+#include <asm/io.h>
+#include <mach/ixp4xx-regs.h>
+
+void reset_cpu(ulong addr)
+{
+ /* Use on-chip reset capability */
+ /* This may not work on IXP425 rev. A0 */
+
+ IXP4XX_OSWK = IXP4XX_WDT_KEY;
+ IXP4XX_OSWT = 0; /* request immediate reset */
+ IXP4XX_OSWE = IXP4XX_WDT_RESET_ENABLE | IXP4XX_WDT_COUNT_ENABLE;
+ while (1)
+ ;
+}
diff --git a/arch/arm/mach-ixp4xx/timer.c b/arch/arm/mach-ixp4xx/timer.c
new file mode 100644
index 0000000..722d1e2
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/timer.c
@@ -0,0 +1,42 @@
+#include <common.h>
+#include <init.h>
+#include <asm/armlinux.h>
+#include <asm/io.h>
+#include <mach/ixp4xx-regs.h>
+#include <clock.h>
+
+#define OSTS_FREQUENCY 66666000
+
+/**
+ * @brief Provide a simple clock read
+ *
+ * Nothing is simpler.. read direct from clock and provide it
+ * to the caller.
+ *
+ * @return clock counter
+ */
+static uint64_t ixp4xx_clocksource_read(void)
+{
+ return IXP4XX_OSTS;
+}
+
+static struct clocksource cs = {
+ .read = ixp4xx_clocksource_read,
+ .mask = 0xffffffff,
+ .shift = 10,
+};
+
+/**
+ * @brief Initialize the Clock
+ *
+ * We use the Time-Stamp Timer
+ *
+ * @return result of @ref init_clock
+ */
+static int ixp4xx_clocksource_init(void)
+{
+ cs.mult = clocksource_hz2mult(OSTS_FREQUENCY, cs.shift);
+
+ return init_clock(&cs);
+}
+core_initcall(ixp4xx_clocksource_init);
diff --git a/drivers/serial/serial_ns16550.c b/drivers/serial/serial_ns16550.c
index 820aac5..f1f7595 100644
--- a/drivers/serial/serial_ns16550.c
+++ b/drivers/serial/serial_ns16550.c
@@ -141,8 +141,12 @@ static void ns16550_serial_init_port(struct console_device *cdev)
{
/* initializing the device for the first time */
ns16550_write(cdev, 0x00, lcr); /* select ier reg */
- ns16550_write(cdev, 0x00, ier);
+#ifdef CONFIG_ARCH_IXP4XX
+ ns16550_write(cdev, IER_UUE, ier); /* Enable UART operation */
+#else
+ ns16550_write(cdev, 0x00, ier);
+#endif
#ifdef CONFIG_DRIVER_SERIAL_NS16550_OMAP_EXTENSIONS
ns16550_write(cdev, 0x07, mdr1); /* Disable */
#endif
diff --git a/drivers/serial/serial_ns16550.h b/drivers/serial/serial_ns16550.h
index db8fe64..132f46e 100644
--- a/drivers/serial/serial_ns16550.h
+++ b/drivers/serial/serial_ns16550.h
@@ -50,6 +50,8 @@
#define dll rbr
#define dlm ier
+#define IER_UUE 0x40 /* UART Unit Enable (XScale) */
+
#define FCR_FIFO_EN 0x01 /* Fifo enable */
#define FCR_RXSR 0x02 /* Receiver soft reset */
#define FCR_TXSR 0x04 /* Transmitter soft reset */
--
1.7.9.1
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* [PATCH 03/10] ARM: Add support for IXP4xx Network Process Engine and queue Manager support
2012-04-23 6:56 [PATCH 00/10] IXP4xx rebase WIP Jean-Christophe PLAGNIOL-VILLARD
2012-04-23 7:02 ` [PATCH 01/10] ARM: add support of in_be16/32 and out_be16/32 Jean-Christophe PLAGNIOL-VILLARD
2012-04-23 7:02 ` [PATCH 02/10] ARM: Add support for IXP4xx CPU Jean-Christophe PLAGNIOL-VILLARD
@ 2012-04-23 7:02 ` Jean-Christophe PLAGNIOL-VILLARD
2012-04-23 7:02 ` [PATCH 04/10] net: Add support for IXP4xx ethernet support Jean-Christophe PLAGNIOL-VILLARD
` (7 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-04-23 7:02 UTC (permalink / raw)
To: barebox; +Cc: Krzysztof Hałasa
From: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
arch/arm/mach-ixp4xx/Kconfig | 12 +
arch/arm/mach-ixp4xx/Makefile | 2 +
arch/arm/mach-ixp4xx/include/mach/npe.h | 30 ++
arch/arm/mach-ixp4xx/include/mach/platform.h | 16 +
arch/arm/mach-ixp4xx/include/mach/qmgr.h | 164 +++++++
arch/arm/mach-ixp4xx/npe.c | 668 ++++++++++++++++++++++++++
arch/arm/mach-ixp4xx/qmgr.c | 259 ++++++++++
7 files changed, 1151 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/mach-ixp4xx/include/mach/npe.h
create mode 100644 arch/arm/mach-ixp4xx/include/mach/qmgr.h
create mode 100644 arch/arm/mach-ixp4xx/npe.c
create mode 100644 arch/arm/mach-ixp4xx/qmgr.c
diff --git a/arch/arm/mach-ixp4xx/Kconfig b/arch/arm/mach-ixp4xx/Kconfig
index 65778ab..d92832c 100644
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -5,4 +5,16 @@ choice
endchoice
+config IXP4XX_QMGR
+ tristate "IXP4xx Queue Manager support"
+ help
+ This driver supports IXP4xx built-in hardware queue manager
+ and is required by the Ethernet driver.
+
+config IXP4XX_NPE
+ tristate "IXP4xx Network Processor Engine support"
+ help
+ This driver supports IXP4xx built-in network coprocessors
+ and is required by the Ethernet driver.
+
endif
diff --git a/arch/arm/mach-ixp4xx/Makefile b/arch/arm/mach-ixp4xx/Makefile
index 6e57c91..9bb2e99 100644
--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
@@ -2,3 +2,5 @@ obj-y += lowlevel_init.o
obj-y += devices.o
obj-y += timer.o
obj-y += reset.o
+obj-$(CONFIG_IXP4XX_QMGR) += qmgr.o
+obj-$(CONFIG_IXP4XX_NPE) += npe.o
diff --git a/arch/arm/mach-ixp4xx/include/mach/npe.h b/arch/arm/mach-ixp4xx/include/mach/npe.h
new file mode 100644
index 0000000..18bd01b
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/include/mach/npe.h
@@ -0,0 +1,30 @@
+#ifndef __IXP4XX_NPE_H
+#define __IXP4XX_NPE_H
+
+#include <common.h>
+
+#define NPE_NAME_LENGTH 5
+
+struct npe_regs {
+ u32 exec_addr, exec_data, exec_status_cmd, exec_count;
+ u32 action_points[4];
+ u32 watchpoint_fifo, watch_count;
+ u32 profile_count;
+ u32 messaging_status, messaging_control;
+ u32 mailbox_status, /*messaging_*/ in_out_fifo;
+};
+
+struct npe {
+ struct npe_regs *regs;
+ int id, valid;
+ const char name[NPE_NAME_LENGTH + 1];
+};
+
+int npe_running(struct npe *npe);
+int npe_send_message(struct npe *npe, const void *msg, const char *what);
+int npe_recv_message(struct npe *npe, void *msg, const char *what);
+int npe_send_recv_message(struct npe *npe, void *msg, const char *what);
+int npe_load_firmware(struct npe *npe);
+struct npe *npe_request(int id);
+
+#endif /* __IXP4XX_NPE_H */
diff --git a/arch/arm/mach-ixp4xx/include/mach/platform.h b/arch/arm/mach-ixp4xx/include/mach/platform.h
index ae4b767..bff9185 100644
--- a/arch/arm/mach-ixp4xx/include/mach/platform.h
+++ b/arch/arm/mach-ixp4xx/include/mach/platform.h
@@ -9,6 +9,20 @@
#define REG_OFFSET 3
#endif
+#define IXP4XX_ETH_NPEA 0x00
+#define IXP4XX_ETH_NPEB 0x10
+#define IXP4XX_ETH_NPEC 0x20
+
+/* Information about built-in Ethernet MAC interfaces */
+struct eth_plat_info {
+ void *regs;
+ u8 npe;
+ u8 phy; /* MII PHY ID, 0 - 31 */
+ u8 rxq; /* configurable, currently 0 - 31 only */
+ u8 txreadyq;
+ u8 hwaddr[6];
+};
+
struct device_d* ixp4xx_add_uart(int id, u32 base);
static inline struct device_d* ixp4xx_add_uart1(void)
@@ -21,4 +35,6 @@ static inline struct device_d* ixp4xx_add_uart2(void)
return ixp4xx_add_uart(1, (u32)IXP4XX_UART2_BASE);
}
+struct device_d* ixp4xx_add_eth(int id, struct eth_plat_info *pdata);
+
#endif /* __MACH_PLATFORM__ */
diff --git a/arch/arm/mach-ixp4xx/include/mach/qmgr.h b/arch/arm/mach-ixp4xx/include/mach/qmgr.h
new file mode 100644
index 0000000..33049b1
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/include/mach/qmgr.h
@@ -0,0 +1,164 @@
+/*
+ * Copyright (C) 2007 Krzysztof Halasa <khc at pm.waw.pl>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ */
+
+#ifndef IXP4XX_QMGR_H
+#define IXP4XX_QMGR_H
+
+#include <common.h>
+#include <mach/ixp4xx-regs.h>
+#include <asm/io.h>
+
+#define DEBUG_QMGR 0
+
+#define HALF_QUEUES 32
+#define QUEUES 64
+#define MAX_QUEUE_LENGTH 4 /* in dwords */
+
+#define QUEUE_STAT1_EMPTY 1 /* queue status bits */
+#define QUEUE_STAT1_NEARLY_EMPTY 2
+#define QUEUE_STAT1_NEARLY_FULL 4
+#define QUEUE_STAT1_FULL 8
+#define QUEUE_STAT2_UNDERFLOW 1
+#define QUEUE_STAT2_OVERFLOW 2
+
+#define QUEUE_WATERMARK_0_ENTRIES 0
+#define QUEUE_WATERMARK_1_ENTRY 1
+#define QUEUE_WATERMARK_2_ENTRIES 2
+#define QUEUE_WATERMARK_4_ENTRIES 3
+#define QUEUE_WATERMARK_8_ENTRIES 4
+#define QUEUE_WATERMARK_16_ENTRIES 5
+#define QUEUE_WATERMARK_32_ENTRIES 6
+#define QUEUE_WATERMARK_64_ENTRIES 7
+
+/* queue interrupt request conditions */
+#define QUEUE_IRQ_SRC_EMPTY 0
+#define QUEUE_IRQ_SRC_NEARLY_EMPTY 1
+#define QUEUE_IRQ_SRC_NEARLY_FULL 2
+#define QUEUE_IRQ_SRC_FULL 3
+#define QUEUE_IRQ_SRC_NOT_EMPTY 4
+#define QUEUE_IRQ_SRC_NOT_NEARLY_EMPTY 5
+#define QUEUE_IRQ_SRC_NOT_NEARLY_FULL 6
+#define QUEUE_IRQ_SRC_NOT_FULL 7
+
+struct qmgr_regs {
+ u32 acc[QUEUES][MAX_QUEUE_LENGTH]; /* 0x000 - 0x3FF */
+ u32 stat1[4]; /* 0x400 - 0x40F */
+ u32 stat2[2]; /* 0x410 - 0x417 */
+ u32 statne_h; /* 0x418 - queue nearly empty */
+ u32 statf_h; /* 0x41C - queue full */
+ u32 irqsrc[4]; /* 0x420 - 0x42F IRC source */
+ u32 irqen[2]; /* 0x430 - 0x437 IRQ enabled */
+ u32 irqstat[2]; /* 0x438 - 0x43F - IRQ access only */
+ u32 reserved[1776];
+ u32 sram[2048]; /* 0x2000 - 0x3FFF - config and buffer */
+};
+
+static const struct qmgr_regs *qmgr_regs = (struct qmgr_regs *)IXP4XX_QMGR_BASE;
+
+void qmgr_set_irq(unsigned int queue, int src,
+ void (*handler)(void *pdev), void *pdev);
+void qmgr_enable_irq(unsigned int queue);
+void qmgr_disable_irq(unsigned int queue);
+
+/* request_ and release_queue() must be called from non-IRQ context */
+
+#if DEBUG_QMGR
+extern char qmgr_queue_descs[HALF_QUEUES][32];
+
+void qmgr_request_queue(unsigned int queue, unsigned int len /* dwords */,
+ unsigned int nearly_empty_watermark,
+ unsigned int nearly_full_watermark,
+ const char *desc_format, const char* name);
+#else
+void __qmgr_request_queue(unsigned int queue, unsigned int len /* dwords */,
+ unsigned int nearly_empty_watermark,
+ unsigned int nearly_full_watermark);
+#define qmgr_request_queue(queue, len, nearly_empty_watermark, \
+ nearly_full_watermark, desc_format, name) \
+ __qmgr_request_queue(queue, len, nearly_empty_watermark, \
+ nearly_full_watermark)
+#endif
+
+void qmgr_release_queue(unsigned int queue);
+
+
+static inline void qmgr_put_entry(unsigned int queue, u32 val)
+{
+#if DEBUG_QMGR
+ BUG_ON(!qmgr_queue_descs[queue]); /* not yet requested */
+
+ fprintf(stderr, "Queue %s(%i) put %X\n",
+ qmgr_queue_descs[queue], queue, val);
+#endif
+ __raw_writel(val, &qmgr_regs->acc[queue][0]);
+}
+
+static inline u32 qmgr_get_entry(unsigned int queue)
+{
+ u32 val;
+ val = __raw_readl(&qmgr_regs->acc[queue][0]);
+#if DEBUG_QMGR
+ BUG_ON(!qmgr_queue_descs[queue]); /* not yet requested */
+
+ fprintf(stderr, "Queue %s(%i) get %X\n",
+ qmgr_queue_descs[queue], queue, val);
+#endif
+ return val;
+}
+
+static inline int __qmgr_get_stat1(unsigned int queue)
+{
+ return (__raw_readl(&qmgr_regs->stat1[queue >> 3])
+ >> ((queue & 7) << 2)) & 0xF;
+}
+
+/**
+ * qmgr_stat_empty() - checks if a hardware queue is empty
+ * @queue: queue number
+ *
+ * Returns non-zero value if the queue is empty.
+ */
+static inline int qmgr_stat_empty(unsigned int queue)
+{
+ return __qmgr_get_stat1(queue) & QUEUE_STAT1_EMPTY;
+}
+
+/**
+ * qmgr_stat_below_low_watermark() - checks if a queue is below low watermark
+ * @queue: queue number
+ *
+ * Returns non-zero value if the queue is below low watermark.
+ */
+static inline int qmgr_stat_below_low_watermark(unsigned int queue)
+{
+ return __qmgr_get_stat1(queue) & QUEUE_STAT1_NEARLY_EMPTY;
+}
+
+/**
+ * qmgr_stat_above_high_watermark() - checks if a queue is above high watermark
+ * @queue: queue number
+ *
+ * Returns non-zero value if the queue is above high watermark
+ */
+static inline int qmgr_stat_above_high_watermark(unsigned int queue)
+{
+ return __qmgr_get_stat1(queue) & QUEUE_STAT1_NEARLY_FULL;
+}
+
+/**
+ * qmgr_stat_full() - checks if a hardware queue is full
+ * @queue: queue number
+ *
+ * Returns non-zero value if the queue is full.
+ */
+static inline int qmgr_stat_full(unsigned int queue)
+{
+ return __qmgr_get_stat1(queue) & QUEUE_STAT1_FULL;
+}
+
+#endif
diff --git a/arch/arm/mach-ixp4xx/npe.c b/arch/arm/mach-ixp4xx/npe.c
new file mode 100644
index 0000000..d82d2d9
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/npe.c
@@ -0,0 +1,668 @@
+/*
+ * Intel IXP4xx Network Processor Engine driver for Linux
+ *
+ * Copyright (C) 2007 Krzysztof Halasa <khc at pm.waw.pl>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <fs.h>
+#include <init.h>
+#include <malloc.h>
+#include <asm/byteorder.h>
+#include <asm/io.h>
+#include <mach/ixp4xx-regs.h>
+#include <mach/cpu.h>
+#include <mach/npe.h>
+
+#define DEBUG_MSG 0
+#define DEBUG_FW 0
+
+#define NPE_COUNT 3
+#define MAX_RETRIES 1000 /* microseconds */
+#define NPE_42X_DATA_SIZE 0x800 /* in dwords */
+#define NPE_46X_DATA_SIZE 0x1000
+#define NPE_A_42X_INSTR_SIZE 0x1000
+#define NPE_B_AND_C_42X_INSTR_SIZE 0x800
+#define NPE_46X_INSTR_SIZE 0x1000
+#define REGS_SIZE 0x1000
+
+#define NPE_PHYS_REG 32
+
+#define FW_MAGIC 0xFEEDF00D
+#define FW_BLOCK_TYPE_INSTR 0x0
+#define FW_BLOCK_TYPE_DATA 0x1
+#define FW_BLOCK_TYPE_EOF 0xF
+
+/* NPE exec status (read) and command (write) */
+#define CMD_NPE_STEP 0x01
+#define CMD_NPE_START 0x02
+#define CMD_NPE_STOP 0x03
+#define CMD_NPE_CLR_PIPE 0x04
+#define CMD_CLR_PROFILE_CNT 0x0C
+#define CMD_RD_INS_MEM 0x10 /* instruction memory */
+#define CMD_WR_INS_MEM 0x11
+#define CMD_RD_DATA_MEM 0x12 /* data memory */
+#define CMD_WR_DATA_MEM 0x13
+#define CMD_RD_ECS_REG 0x14 /* exec access register */
+#define CMD_WR_ECS_REG 0x15
+
+#define STAT_RUN 0x80000000
+#define STAT_STOP 0x40000000
+#define STAT_CLEAR 0x20000000
+#define STAT_ECS_K 0x00800000 /* pipeline clean */
+
+#define NPE_STEVT 0x1B
+#define NPE_STARTPC 0x1C
+#define NPE_REGMAP 0x1E
+#define NPE_CINDEX 0x1F
+
+#define INSTR_WR_REG_SHORT 0x0000C000
+#define INSTR_WR_REG_BYTE 0x00004000
+#define INSTR_RD_FIFO 0x0F888220
+#define INSTR_RESET_MBOX 0x0FAC8210
+
+#define ECS_BG_CTXT_REG_0 0x00 /* Background Executing Context */
+#define ECS_BG_CTXT_REG_1 0x01 /* Stack level */
+#define ECS_BG_CTXT_REG_2 0x02
+#define ECS_PRI_1_CTXT_REG_0 0x04 /* Priority 1 Executing Context */
+#define ECS_PRI_1_CTXT_REG_1 0x05 /* Stack level */
+#define ECS_PRI_1_CTXT_REG_2 0x06
+#define ECS_PRI_2_CTXT_REG_0 0x08 /* Priority 2 Executing Context */
+#define ECS_PRI_2_CTXT_REG_1 0x09 /* Stack level */
+#define ECS_PRI_2_CTXT_REG_2 0x0A
+#define ECS_DBG_CTXT_REG_0 0x0C /* Debug Executing Context */
+#define ECS_DBG_CTXT_REG_1 0x0D /* Stack level */
+#define ECS_DBG_CTXT_REG_2 0x0E
+#define ECS_INSTRUCT_REG 0x11 /* NPE Instruction Register */
+
+#define ECS_REG_0_ACTIVE 0x80000000 /* all levels */
+#define ECS_REG_0_NEXTPC_MASK 0x1FFF0000 /* BG/PRI1/PRI2 levels */
+#define ECS_REG_0_LDUR_BITS 8
+#define ECS_REG_0_LDUR_MASK 0x00000700 /* all levels */
+#define ECS_REG_1_CCTXT_BITS 16
+#define ECS_REG_1_CCTXT_MASK 0x000F0000 /* all levels */
+#define ECS_REG_1_SELCTXT_BITS 0
+#define ECS_REG_1_SELCTXT_MASK 0x0000000F /* all levels */
+#define ECS_DBG_REG_2_IF 0x00100000 /* debug level */
+#define ECS_DBG_REG_2_IE 0x00080000 /* debug level */
+
+/* NPE watchpoint_fifo register bit */
+#define WFIFO_VALID 0x80000000
+
+/* NPE messaging_status register bit definitions */
+#define MSGSTAT_OFNE 0x00010000 /* OutFifoNotEmpty */
+#define MSGSTAT_IFNF 0x00020000 /* InFifoNotFull */
+#define MSGSTAT_OFNF 0x00040000 /* OutFifoNotFull */
+#define MSGSTAT_IFNE 0x00080000 /* InFifoNotEmpty */
+#define MSGSTAT_MBINT 0x00100000 /* Mailbox interrupt */
+#define MSGSTAT_IFINT 0x00200000 /* InFifo interrupt */
+#define MSGSTAT_OFINT 0x00400000 /* OutFifo interrupt */
+#define MSGSTAT_WFINT 0x00800000 /* WatchFifo interrupt */
+
+/* NPE messaging_control register bit definitions */
+#define MSGCTL_OUT_FIFO 0x00010000 /* enable output FIFO */
+#define MSGCTL_IN_FIFO 0x00020000 /* enable input FIFO */
+#define MSGCTL_OUT_FIFO_WRITE 0x01000000 /* enable FIFO + WRITE */
+#define MSGCTL_IN_FIFO_WRITE 0x02000000
+
+/* NPE mailbox_status value for reset */
+#define RESET_MBOX_STAT 0x0000F0F0
+
+#define print_npe(npe, fmt, ...) fprintf(stderr, "%s: " fmt, npe->name, ## __VA_ARGS__)
+
+#if DEBUG_MSG
+#define debug_msg(npe, fmt, ...) print_npe(npe, fmt, ## __VA_ARGS__)
+#else
+#define debug_msg(npe, fmt, ...)
+#endif
+
+static struct {
+ u32 reg, val;
+} ecs_reset[] = {
+ {ECS_BG_CTXT_REG_0, 0xA0000000},
+ {ECS_BG_CTXT_REG_1, 0x01000000},
+ {ECS_BG_CTXT_REG_2, 0x00008000},
+ {ECS_PRI_1_CTXT_REG_0, 0x20000080},
+ {ECS_PRI_1_CTXT_REG_1, 0x01000000},
+ {ECS_PRI_1_CTXT_REG_2, 0x00008000},
+ {ECS_PRI_2_CTXT_REG_0, 0x20000080},
+ {ECS_PRI_2_CTXT_REG_1, 0x01000000},
+ {ECS_PRI_2_CTXT_REG_2, 0x00008000},
+ {ECS_DBG_CTXT_REG_0, 0x20000000},
+ {ECS_DBG_CTXT_REG_1, 0x00000000},
+ {ECS_DBG_CTXT_REG_2, 0x001E0000},
+ {ECS_INSTRUCT_REG, 0x1003C00F},
+};
+
+static struct npe npe_tab[NPE_COUNT] = {
+ {
+ .regs = (struct npe_regs *)IXP4XX_NPEA_BASE,
+ .id = 0,
+ .name = "NPE-A",
+ }, {
+ .regs = (struct npe_regs *)IXP4XX_NPEB_BASE,
+ .id = 1,
+ .name = "NPE-B",
+ }, {
+ .regs = (struct npe_regs *)IXP4XX_NPEC_BASE,
+ .id = 2,
+ .name = "NPE-C",
+ }
+};
+
+int npe_running(struct npe *npe)
+{
+ return (__raw_readl(&npe->regs->exec_status_cmd) & STAT_RUN) != 0;
+}
+
+static void npe_cmd_write(struct npe *npe, u32 addr, int cmd, u32 data)
+{
+ __raw_writel(data, &npe->regs->exec_data);
+ __raw_writel(addr, &npe->regs->exec_addr);
+ __raw_writel(cmd, &npe->regs->exec_status_cmd);
+}
+
+static u32 npe_cmd_read(struct npe *npe, u32 addr, int cmd)
+{
+ __raw_writel(addr, &npe->regs->exec_addr);
+ __raw_writel(cmd, &npe->regs->exec_status_cmd);
+ /* Iintroduce extra read cycles after issuing read command to NPE
+ so that we read the register after the NPE has updated it.
+ This is to overcome race condition between XScale and NPE */
+ __raw_readl(&npe->regs->exec_data);
+ __raw_readl(&npe->regs->exec_data);
+ return __raw_readl(&npe->regs->exec_data);
+}
+
+static void npe_clear_active(struct npe *npe, u32 reg)
+{
+ u32 val = npe_cmd_read(npe, reg, CMD_RD_ECS_REG);
+ npe_cmd_write(npe, reg, CMD_WR_ECS_REG, val & ~ECS_REG_0_ACTIVE);
+}
+
+static void npe_start(struct npe *npe)
+{
+ /* ensure only Background Context Stack Level is active */
+ npe_clear_active(npe, ECS_PRI_1_CTXT_REG_0);
+ npe_clear_active(npe, ECS_PRI_2_CTXT_REG_0);
+ npe_clear_active(npe, ECS_DBG_CTXT_REG_0);
+
+ __raw_writel(CMD_NPE_CLR_PIPE, &npe->regs->exec_status_cmd);
+ __raw_writel(CMD_NPE_START, &npe->regs->exec_status_cmd);
+}
+
+static void npe_stop(struct npe *npe)
+{
+ __raw_writel(CMD_NPE_STOP, &npe->regs->exec_status_cmd);
+ __raw_writel(CMD_NPE_CLR_PIPE, &npe->regs->exec_status_cmd); /*FIXME?*/
+}
+
+static int npe_debug_instr(struct npe *npe, u32 instr, u32 ctx, u32 ldur)
+{
+ u32 wc;
+ int i;
+
+ /* set the Active bit, and the LDUR, in the debug level */
+ npe_cmd_write(npe, ECS_DBG_CTXT_REG_0, CMD_WR_ECS_REG,
+ ECS_REG_0_ACTIVE | (ldur << ECS_REG_0_LDUR_BITS));
+
+ /* set CCTXT at ECS DEBUG L3 to specify in which context to execute
+ the instruction, and set SELCTXT at ECS DEBUG Level to specify
+ which context store to access.
+ Debug ECS Level Reg 1 has form 0x000n000n, where n = context number
+ */
+ npe_cmd_write(npe, ECS_DBG_CTXT_REG_1, CMD_WR_ECS_REG,
+ (ctx << ECS_REG_1_CCTXT_BITS) |
+ (ctx << ECS_REG_1_SELCTXT_BITS));
+
+ /* clear the pipeline */
+ __raw_writel(CMD_NPE_CLR_PIPE, &npe->regs->exec_status_cmd);
+
+ /* load NPE instruction into the instruction register */
+ npe_cmd_write(npe, ECS_INSTRUCT_REG, CMD_WR_ECS_REG, instr);
+
+ /* we need this value later to wait for completion of NPE execution
+ step */
+ wc = __raw_readl(&npe->regs->watch_count);
+
+ /* issue a Step One command via the Execution Control register */
+ __raw_writel(CMD_NPE_STEP, &npe->regs->exec_status_cmd);
+
+ /* Watch Count register increments when NPE completes an instruction */
+ for (i = 0; i < MAX_RETRIES; i++) {
+ if (wc != __raw_readl(&npe->regs->watch_count))
+ return 0;
+ udelay(1);
+ }
+
+ print_npe(npe, "reset: npe_debug_instr(): timeout\n");
+ return -ETIMEDOUT;
+}
+
+static int npe_logical_reg_write8(struct npe *npe, u32 addr, u8 val, u32 ctx)
+{
+ /* here we build the NPE assembler instruction: mov8 d0, #0 */
+ u32 instr = INSTR_WR_REG_BYTE | /* OpCode */
+ addr << 9 | /* base Operand */
+ (val & 0x1F) << 4 | /* lower 5 bits to immediate data */
+ (val & ~0x1F) << (18 - 5);/* higher 3 bits to CoProc instr. */
+ return npe_debug_instr(npe, instr, ctx, 1); /* execute it */
+}
+
+static int npe_logical_reg_write16(struct npe *npe, u32 addr, u16 val, u32 ctx)
+{
+ /* here we build the NPE assembler instruction: mov16 d0, #0 */
+ u32 instr = INSTR_WR_REG_SHORT | /* OpCode */
+ addr << 9 | /* base Operand */
+ (val & 0x1F) << 4 | /* lower 5 bits to immediate data */
+ (val & ~0x1F) << (18 - 5);/* higher 11 bits to CoProc instr. */
+ return npe_debug_instr(npe, instr, ctx, 1); /* execute it */
+}
+
+static int npe_logical_reg_write32(struct npe *npe, u32 addr, u32 val, u32 ctx)
+{
+ /* write in 16 bit steps first the high and then the low value */
+ if (npe_logical_reg_write16(npe, addr, val >> 16, ctx))
+ return -ETIMEDOUT;
+ return npe_logical_reg_write16(npe, addr + 2, val & 0xFFFF, ctx);
+}
+
+static int npe_reset(struct npe *npe)
+{
+ u32 val, ctl, exec_count, ctx_reg2;
+ int i;
+
+ ctl = (__raw_readl(&npe->regs->messaging_control) | 0x3F000000) &
+ 0x3F3FFFFF;
+
+ /* disable parity interrupt */
+ __raw_writel(ctl & 0x3F00FFFF, &npe->regs->messaging_control);
+
+ /* pre exec - debug instruction */
+ /* turn off the halt bit by clearing Execution Count register. */
+ exec_count = __raw_readl(&npe->regs->exec_count);
+ __raw_writel(0, &npe->regs->exec_count);
+ /* ensure that IF and IE are on (temporarily), so that we don't end up
+ stepping forever */
+ ctx_reg2 = npe_cmd_read(npe, ECS_DBG_CTXT_REG_2, CMD_RD_ECS_REG);
+ npe_cmd_write(npe, ECS_DBG_CTXT_REG_2, CMD_WR_ECS_REG, ctx_reg2 |
+ ECS_DBG_REG_2_IF | ECS_DBG_REG_2_IE);
+
+ /* clear the FIFOs */
+ while (__raw_readl(&npe->regs->watchpoint_fifo) & WFIFO_VALID)
+ ;
+ while (__raw_readl(&npe->regs->messaging_status) & MSGSTAT_OFNE)
+ /* read from the outFIFO until empty */
+ print_npe(npe, "npe_reset: read FIFO = 0x%X\n",
+ __raw_readl(&npe->regs->in_out_fifo));
+
+ while (__raw_readl(&npe->regs->messaging_status) & MSGSTAT_IFNE)
+ /* step execution of the NPE intruction to read inFIFO using
+ the Debug Executing Context stack */
+ if (npe_debug_instr(npe, INSTR_RD_FIFO, 0, 0))
+ return -ETIMEDOUT;
+
+ /* reset the mailbox reg from the XScale side */
+ __raw_writel(RESET_MBOX_STAT, &npe->regs->mailbox_status);
+ /* from NPE side */
+ if (npe_debug_instr(npe, INSTR_RESET_MBOX, 0, 0))
+ return -ETIMEDOUT;
+
+ /* Reset the physical registers in the NPE register file */
+ for (val = 0; val < NPE_PHYS_REG; val++) {
+ if (npe_logical_reg_write16(npe, NPE_REGMAP, val >> 1, 0))
+ return -ETIMEDOUT;
+ /* address is either 0 or 4 */
+ if (npe_logical_reg_write32(npe, (val & 1) * 4, 0, 0))
+ return -ETIMEDOUT;
+ }
+
+ /* Reset the context store = each context's Context Store registers */
+
+ /* Context 0 has no STARTPC. Instead, this value is used to set NextPC
+ for Background ECS, to set where NPE starts executing code */
+ val = npe_cmd_read(npe, ECS_BG_CTXT_REG_0, CMD_RD_ECS_REG);
+ val &= ~ECS_REG_0_NEXTPC_MASK;
+ val |= (0 /* NextPC */ << 16) & ECS_REG_0_NEXTPC_MASK;
+ npe_cmd_write(npe, ECS_BG_CTXT_REG_0, CMD_WR_ECS_REG, val);
+
+ for (i = 0; i < 16; i++) {
+ if (i) { /* Context 0 has no STEVT nor STARTPC */
+ /* STEVT = off, 0x80 */
+ if (npe_logical_reg_write8(npe, NPE_STEVT, 0x80, i))
+ return -ETIMEDOUT;
+ if (npe_logical_reg_write16(npe, NPE_STARTPC, 0, i))
+ return -ETIMEDOUT;
+ }
+ /* REGMAP = d0->p0, d8->p2, d16->p4 */
+ if (npe_logical_reg_write16(npe, NPE_REGMAP, 0x820, i))
+ return -ETIMEDOUT;
+ if (npe_logical_reg_write8(npe, NPE_CINDEX, 0, i))
+ return -ETIMEDOUT;
+ }
+
+ /* post exec */
+ /* clear active bit in debug level */
+ npe_cmd_write(npe, ECS_DBG_CTXT_REG_0, CMD_WR_ECS_REG, 0);
+ /* clear the pipeline */
+ __raw_writel(CMD_NPE_CLR_PIPE, &npe->regs->exec_status_cmd);
+ /* restore previous values */
+ __raw_writel(exec_count, &npe->regs->exec_count);
+ npe_cmd_write(npe, ECS_DBG_CTXT_REG_2, CMD_WR_ECS_REG, ctx_reg2);
+
+ /* write reset values to Execution Context Stack registers */
+ for (val = 0; val < ARRAY_SIZE(ecs_reset); val++)
+ npe_cmd_write(npe, ecs_reset[val].reg, CMD_WR_ECS_REG,
+ ecs_reset[val].val);
+
+ /* clear the profile counter */
+ __raw_writel(CMD_CLR_PROFILE_CNT, &npe->regs->exec_status_cmd);
+
+ __raw_writel(0, &npe->regs->exec_count);
+ __raw_writel(0, &npe->regs->action_points[0]);
+ __raw_writel(0, &npe->regs->action_points[1]);
+ __raw_writel(0, &npe->regs->action_points[2]);
+ __raw_writel(0, &npe->regs->action_points[3]);
+ __raw_writel(0, &npe->regs->watch_count);
+
+ val = ixp4xx_read_feature_bits();
+ /* reset the NPE */
+ ixp4xx_write_feature_bits(val &
+ ~(IXP4XX_FEATURE_RESET_NPEA << npe->id));
+ /* deassert reset */
+ ixp4xx_write_feature_bits(val |
+ (IXP4XX_FEATURE_RESET_NPEA << npe->id));
+ for (i = 0; i < MAX_RETRIES; i++) {
+ if (ixp4xx_read_feature_bits() &
+ (IXP4XX_FEATURE_RESET_NPEA << npe->id))
+ break; /* NPE is back alive */
+ udelay(1);
+ }
+ if (i == MAX_RETRIES)
+ return -ETIMEDOUT;
+
+ npe_stop(npe);
+
+ /* restore NPE configuration bus Control Register - parity settings */
+ __raw_writel(ctl, &npe->regs->messaging_control);
+ return 0;
+}
+
+
+int npe_send_message(struct npe *npe, const void *msg, const char *what)
+{
+ const u32 *send = msg;
+ int cycles = 0;
+
+ debug_msg(npe, "Trying to send message %s [%08X:%08X]\n",
+ what, send[0], send[1]);
+
+ if (__raw_readl(&npe->regs->messaging_status) & MSGSTAT_IFNE) {
+ debug_msg(npe, "NPE input FIFO not empty\n");
+ return -EIO;
+ }
+
+ __raw_writel(send[0], &npe->regs->in_out_fifo);
+
+ if (!(__raw_readl(&npe->regs->messaging_status) & MSGSTAT_IFNF)) {
+ debug_msg(npe, "NPE input FIFO full\n");
+ return -EIO;
+ }
+
+ __raw_writel(send[1], &npe->regs->in_out_fifo);
+
+ while ((cycles < MAX_RETRIES) &&
+ (__raw_readl(&npe->regs->messaging_status) & MSGSTAT_IFNE)) {
+ udelay(1);
+ cycles++;
+ }
+
+ if (cycles == MAX_RETRIES) {
+ debug_msg(npe, "Timeout sending message\n");
+ return -ETIMEDOUT;
+ }
+
+#if DEBUG_MSG > 1
+ debug_msg(npe, "Sending a message took %i cycles\n", cycles);
+#endif
+ return 0;
+}
+
+int npe_recv_message(struct npe *npe, void *msg, const char *what)
+{
+ u32 *recv = msg;
+ int cycles = 0, cnt = 0;
+
+ debug_msg(npe, "Trying to receive message %s\n", what);
+
+ while (cycles < MAX_RETRIES) {
+ if (__raw_readl(&npe->regs->messaging_status) & MSGSTAT_OFNE) {
+ recv[cnt++] = __raw_readl(&npe->regs->in_out_fifo);
+ if (cnt == 2)
+ break;
+ } else {
+ udelay(1);
+ cycles++;
+ }
+ }
+
+ switch(cnt) {
+ case 1:
+ debug_msg(npe, "Received [%08X]\n", recv[0]);
+ break;
+ case 2:
+ debug_msg(npe, "Received [%08X:%08X]\n", recv[0], recv[1]);
+ break;
+ }
+
+ if (cycles == MAX_RETRIES) {
+ debug_msg(npe, "Timeout waiting for message\n");
+ return -ETIMEDOUT;
+ }
+
+#if DEBUG_MSG > 1
+ debug_msg(npe, "Receiving a message took %i cycles\n", cycles);
+#endif
+ return 0;
+}
+
+int npe_send_recv_message(struct npe *npe, void *msg, const char *what)
+{
+ int result;
+ u32 *send = msg, recv[2];
+
+ if ((result = npe_send_message(npe, msg, what)) != 0)
+ return result;
+ if ((result = npe_recv_message(npe, recv, what)) != 0)
+ return result;
+
+ if ((recv[0] != send[0]) || (recv[1] != send[1])) {
+ debug_msg(npe, "Message %s: unexpected message received\n",
+ what);
+ return -EIO;
+ }
+ return 0;
+}
+
+
+int npe_load_firmware(struct npe *npe)
+{
+ struct dl_block {
+ u32 type;
+ u32 offset;
+ } *blk;
+
+ struct dl_image {
+ u32 magic;
+ u32 id;
+ u32 size;
+ union {
+ u32 data[0];
+ struct dl_block blocks[0];
+ };
+ } *image;
+
+ struct dl_codeblock {
+ u32 npe_addr;
+ u32 size;
+ u32 data[0];
+ } *cb;
+
+ int i, j, err, data_size, instr_size, blocks, table_end;
+ u32 cmd;
+ char name[5 /* "/firmware/" */ + NPE_NAME_LENGTH + 1 /* NUL */];
+ size_t image_size;
+
+ sprintf(name, "/firmware/%s", npe->name);
+ if (!(image = read_file(name, &image_size))) {
+ print_npe(npe, "bad or missing microcode file %s", name);
+ return -EIO;
+ }
+
+ err = -EINVAL;
+ if (image_size < sizeof(struct dl_image)) {
+ print_npe(npe, "incomplete microcode file %s\n", name);
+ goto err;
+ }
+
+#if DEBUG_FW
+ print_npe(npe, "microcode: %08X %08X %08X (0x%X bytes)\n",
+ image->magic, image->id, image->size, image->size * 4);
+#endif
+
+ if (image->magic == swab32(FW_MAGIC)) { /* swapped file */
+ image->id = swab32(image->id);
+ image->size = swab32(image->size);
+ } else if (image->magic != FW_MAGIC) {
+ print_npe(npe, "bad microcode file %s magic: 0x%X\n", name, image->magic);
+ goto err;
+ }
+ if ((image->size * 4 + sizeof(struct dl_image)) > image_size) {
+ print_npe(npe, "incomplete microcode file %s\n", name);
+ goto err;
+ }
+ if (((image->id >> 24) & 0xF /* NPE ID */) != npe->id) {
+ print_npe(npe, "NPE ID mismatch in microcode file %s\n", name);
+ goto err;
+ }
+ if (image->magic == swab32(FW_MAGIC))
+ for (i = 0; i < image->size; i++)
+ image->data[i] = swab32(image->data[i]);
+
+ if (cpu_is_ixp42x() && ((image->id >> 28) & 0xF /* device ID */)) {
+ print_npe(npe, "IXP43x/IXP46x microcode ignored on IXP42x\n");
+ goto err;
+ }
+
+ if (npe_running(npe)) {
+ print_npe(npe, "unable to load microcode file %s, NPE is already running\n", name);
+ err = -EBUSY;
+ goto err;
+ }
+
+ if (cpu_is_ixp42x()) {
+ if (!npe->id)
+ instr_size = NPE_A_42X_INSTR_SIZE;
+ else
+ instr_size = NPE_B_AND_C_42X_INSTR_SIZE;
+ data_size = NPE_42X_DATA_SIZE;
+ } else {
+ instr_size = NPE_46X_INSTR_SIZE;
+ data_size = NPE_46X_DATA_SIZE;
+ }
+
+ for (blocks = 0; blocks * sizeof(struct dl_block) / 4 < image->size;
+ blocks++)
+ if (image->blocks[blocks].type == FW_BLOCK_TYPE_EOF)
+ break;
+ if (blocks * sizeof(struct dl_block) / 4 >= image->size) {
+ print_npe(npe, "microcode EOF block marker not found\n");
+ goto err;
+ }
+
+#if DEBUG_FW
+ print_npe(npe, "%i microcode blocks found\n", blocks);
+#endif
+
+ table_end = blocks * sizeof(struct dl_block) / 4 + 1 /* EOF marker */;
+ for (i = 0, blk = image->blocks; i < blocks; i++, blk++) {
+ if (blk->offset > image->size - sizeof(struct dl_codeblock) / 4
+ || blk->offset < table_end) {
+ print_npe(npe, "invalid offset 0x%X of "
+ "microcode block #%i\n", blk->offset, i);
+ goto err;
+ }
+
+ cb = (struct dl_codeblock*)&image->data[blk->offset];
+ if (blk->type == FW_BLOCK_TYPE_INSTR) {
+ if (cb->npe_addr + cb->size > instr_size)
+ goto too_big;
+ cmd = CMD_WR_INS_MEM;
+ } else if (blk->type == FW_BLOCK_TYPE_DATA) {
+ if (cb->npe_addr + cb->size > data_size)
+ goto too_big;
+ cmd = CMD_WR_DATA_MEM;
+ } else {
+ print_npe(npe, "invalid microcode block #%i type 0x%X\n",
+ i, blk->type);
+ goto err;
+ }
+ if (blk->offset + sizeof(*cb) / 4 + cb->size > image->size) {
+ print_npe(npe, "microcode block #%i doesn't "
+ "fit in microcode image: type %c, start 0x%X,"
+ " length 0x%X\n", i,
+ blk->type == FW_BLOCK_TYPE_INSTR ? 'I' : 'D',
+ cb->npe_addr, cb->size);
+ goto err;
+ }
+
+ for (j = 0; j < cb->size; j++)
+ npe_cmd_write(npe, cb->npe_addr + j, cmd, cb->data[j]);
+ }
+
+ npe_start(npe);
+ if (!npe_running(npe))
+ print_npe(npe, "unable to start\n");
+ free(image);
+ return 0;
+
+too_big:
+ print_npe(npe, "microcode block #%i doesn't fit in NPE "
+ "memory: type %c, start 0x%X, length 0x%X\n", i,
+ blk->type == FW_BLOCK_TYPE_INSTR ? 'I' : 'D',
+ cb->npe_addr, cb->size);
+err:
+ free(image);
+ return err;
+}
+
+
+struct npe *npe_request(int id)
+{
+ if (id < NPE_COUNT)
+ if (npe_tab[id].valid)
+ return &npe_tab[id];
+ return NULL;
+}
+
+static int __init npe_init(void)
+{
+ int i;
+
+ for (i = 0; i < NPE_COUNT; i++) {
+ struct npe *npe = &npe_tab[i];
+ if (!(ixp4xx_read_feature_bits() & (IXP4XX_FEATURE_RESET_NPEA << i)))
+ continue; /* NPE already disabled or not present */
+ if (npe_reset(npe))
+ continue;
+ npe->valid = 1;
+ }
+ return 0;
+}
+
+coredevice_initcall(npe_init);
diff --git a/arch/arm/mach-ixp4xx/qmgr.c b/arch/arm/mach-ixp4xx/qmgr.c
new file mode 100644
index 0000000..55b6724
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/qmgr.c
@@ -0,0 +1,259 @@
+/*
+ * Intel IXP4xx Queue Manager driver for Linux
+ *
+ * Copyright (C) 2007 Krzysztof Halasa <khc at pm.waw.pl>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ */
+
+#include <init.h>
+#include <errno.h>
+#include <mach/qmgr.h>
+
+static u32 used_sram_bitmap[4]; /* 128 16-dword pages */
+
+#if DEBUG_QMGR
+char qmgr_queue_descs[HALF_QUEUES][32];
+#endif
+
+#ifdef CONFIG_USE_IRQ
+
+static void (*irq_handlers[HALF_QUEUES])(void *pdev);
+static void *irq_pdevs[HALF_QUEUES];
+
+void qmgr_set_irq(unsigned int queue, int src,
+ void (*handler)(void *pdev), void *pdev)
+{
+ const u32 *reg;
+ int bit;
+ BUG_ON(src > QUEUE_IRQ_SRC_NOT_FULL);
+ reg = &qmgr_regs->irqsrc[queue >> 3]; /* 8 queues per u32 */
+ bit = (queue % 8) * 4; /* 3 bits + 1 reserved bit per queue */
+ __raw_writel((__raw_readl(reg) & ~(7 << bit)) | (src << bit), reg);
+
+ irq_handlers[queue] = handler;
+ irq_pdevs[queue] = pdev;
+}
+
+
+static void qmgr_irq1_a0(void *data)
+{
+ int i;
+ u32 en_bitmap, src, stat;
+
+ /* ACK - it may clear any bits so don't rely on it */
+ __raw_writel(0xFFFFFFFF, &qmgr_regs->irqstat[0]);
+
+ en_bitmap = qmgr_regs->irqen[0];
+ while (en_bitmap) {
+ i = fls(en_bitmap) - 1; /* number of the last "low" queue */
+ en_bitmap &= ~BIT(i);
+ src = qmgr_regs->irqsrc[i >> 3];
+ stat = qmgr_regs->stat1[i >> 3];
+ if (src & 4) /* the IRQ condition is inverted */
+ stat = ~stat;
+ if (stat & BIT(src & 3))
+ irq_handlers[i](irq_pdevs[i]);
+ }
+}
+
+
+static void qmgr_irq1(void *data)
+{
+ int i;
+ u32 req_bitmap = __raw_readl(&qmgr_regs->irqstat[0]);
+
+ if (!req_bitmap)
+ return;
+ __raw_writel(req_bitmap, &qmgr_regs->irqstat[0]); /* ACK */
+
+ while (req_bitmap) {
+ i = fls(req_bitmap) - 1; /* number of the last queue */
+ req_bitmap &= ~BIT(i);
+ irq_handlers[i](irq_pdevs[i]);
+ }
+}
+
+
+void qmgr_enable_irq(unsigned int queue)
+{
+ u32 mask = 1 << queue;
+
+ __raw_writel(__raw_readl(&qmgr_regs->irqen[0]) | mask,
+ &qmgr_regs->irqen[0]);
+}
+
+void qmgr_disable_irq(unsigned int queue)
+{
+ u32 mask = 1 << queue;
+
+ __raw_writel(__raw_readl(&qmgr_regs->irqen[0]) & ~mask,
+ &qmgr_regs->irqen[0]);
+ __raw_writel(mask, &qmgr_regs->irqstat[0]); /* clear */
+}
+
+#endif /* CONFIG_USE_IRQ */
+
+static inline void shift_mask(u32 *mask)
+{
+ mask[3] = mask[3] << 1 | mask[2] >> 31;
+ mask[2] = mask[2] << 1 | mask[1] >> 31;
+ mask[1] = mask[1] << 1 | mask[0] >> 31;
+ mask[0] <<= 1;
+}
+
+#if DEBUG_QMGR
+void qmgr_request_queue(unsigned int queue, unsigned int len /* dwords */,
+ unsigned int nearly_empty_watermark,
+ unsigned int nearly_full_watermark,
+ const char *desc_format, const char* name)
+#else
+void __qmgr_request_queue(unsigned int queue, unsigned int len /* dwords */,
+ unsigned int nearly_empty_watermark,
+ unsigned int nearly_full_watermark)
+#endif
+{
+ u32 cfg, addr = 0, mask[4]; /* in 16-dwords */
+
+ BUG_ON(queue >= HALF_QUEUES);
+ BUG_ON((nearly_empty_watermark | nearly_full_watermark) & ~7);
+
+ switch (len) {
+ case 16:
+ cfg = 0 << 24;
+ mask[0] = 0x1;
+ break;
+ case 32:
+ cfg = 1 << 24;
+ mask[0] = 0x3;
+ break;
+ case 64:
+ cfg = 2 << 24;
+ mask[0] = 0xF;
+ break;
+ case 128:
+ cfg = 3 << 24;
+ mask[0] = 0xFF;
+ break;
+ default:
+ BUG();
+ }
+
+ cfg |= nearly_empty_watermark << 26;
+ cfg |= nearly_full_watermark << 29;
+ len /= 16; /* in 16-dwords: 1, 2, 4 or 8 */
+ mask[1] = mask[2] = mask[3] = 0;
+
+ BUG_ON(__raw_readl(&qmgr_regs->sram[queue]));
+
+ while (1) {
+ if (!(used_sram_bitmap[0] & mask[0]) &&
+ !(used_sram_bitmap[1] & mask[1]) &&
+ !(used_sram_bitmap[2] & mask[2]) &&
+ !(used_sram_bitmap[3] & mask[3]))
+ break; /* found free space */
+
+ addr++;
+ shift_mask(mask);
+ if (addr + len > ARRAY_SIZE(qmgr_regs->sram)) {
+ fprintf(stderr, "qmgr: no free SRAM space for"
+ " queue %i\n", queue);
+ BUG();
+ }
+ }
+
+ used_sram_bitmap[0] |= mask[0];
+ used_sram_bitmap[1] |= mask[1];
+ used_sram_bitmap[2] |= mask[2];
+ used_sram_bitmap[3] |= mask[3];
+ __raw_writel(cfg | (addr << 14), &qmgr_regs->sram[queue]);
+#if DEBUG_QMGR
+ /* no snprintf() */
+ sprintf(qmgr_queue_descs[queue], desc_format, name);
+ fprintf(stderr, "qmgr: requested queue %s(%i) addr = 0x%02X\n",
+ qmgr_queue_descs[queue], queue, addr);
+#endif
+}
+
+void qmgr_release_queue(unsigned int queue)
+{
+ u32 cfg, addr, mask[4];
+
+ BUG_ON(queue >= HALF_QUEUES); /* not in valid range */
+
+ memset(mask, 0, sizeof(u32) * 4);
+
+ cfg = __raw_readl(&qmgr_regs->sram[queue]);
+ addr = (cfg >> 14) & 0xFF;
+
+ BUG_ON(!addr); /* not requested */
+
+ switch ((cfg >> 24) & 3) {
+ case 0: mask[0] = 0x1; break;
+ case 1: mask[0] = 0x3; break;
+ case 2: mask[0] = 0xF; break;
+ case 3: mask[0] = 0xFF; break;
+ }
+
+ while (addr--)
+ shift_mask(mask);
+
+#if DEBUG_QMGR
+ fprintf(stderr, "qmgr: releasing queue %s(%i)\n",
+ qmgr_queue_descs[queue], queue);
+ qmgr_queue_descs[queue][0] = '\x0';
+#endif
+ __raw_writel(0, &qmgr_regs->sram[queue]);
+
+ used_sram_bitmap[0] &= ~mask[0];
+ used_sram_bitmap[1] &= ~mask[1];
+ used_sram_bitmap[2] &= ~mask[2];
+ used_sram_bitmap[3] &= ~mask[3];
+#ifdef CONFIG_USE_IRQ
+ irq_handlers[queue] = NULL; /* catch IRQ bugs */
+#endif
+
+ while ((addr = qmgr_get_entry(queue)))
+ fprintf(stderr, "qmgr: released queue %i not empty: 0x%08X\n",
+ queue, addr);
+}
+
+static int __init qmgr_init(void)
+{
+ int i;
+#ifdef CONFIG_USE_IRQ
+ interrupt_handler_t *handler;
+#endif
+
+ /* reset qmgr registers */
+ for (i = 0; i < 4; i++) {
+ __raw_writel(0x33333333, &qmgr_regs->stat1[i]);
+ __raw_writel(0, &qmgr_regs->irqsrc[i]);
+ }
+ for (i = 0; i < 2; i++) {
+ __raw_writel(0, &qmgr_regs->stat2[i]);
+ __raw_writel(0xFFFFFFFF, &qmgr_regs->irqstat[i]); /* clear */
+ __raw_writel(0, &qmgr_regs->irqen[i]);
+ }
+
+ __raw_writel(0xFFFFFFFF, &qmgr_regs->statne_h);
+ __raw_writel(0, &qmgr_regs->statf_h);
+
+ for (i = 0; i < QUEUES; i++)
+ __raw_writel(0, &qmgr_regs->sram[i]);
+
+#ifdef CONFIG_USE_IRQ
+ if (cpu_is_ixp42x_rev_a0())
+ handler = qmgr_irq1_a0;
+ else
+ handler = qmgr_irq1;
+
+ irq_install_handler(IXP425_QM1_IRQ, handler, NULL);
+#endif
+ used_sram_bitmap[0] = 0xF; /* 4 first pages reserved for config */
+ return 0;
+}
+
+coredevice_initcall(qmgr_init);
--
1.7.9.1
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* [PATCH 04/10] net: Add support for IXP4xx ethernet support
2012-04-23 6:56 [PATCH 00/10] IXP4xx rebase WIP Jean-Christophe PLAGNIOL-VILLARD
` (2 preceding siblings ...)
2012-04-23 7:02 ` [PATCH 03/10] ARM: Add support for IXP4xx Network Process Engine and queue Manager support Jean-Christophe PLAGNIOL-VILLARD
@ 2012-04-23 7:02 ` Jean-Christophe PLAGNIOL-VILLARD
2012-04-23 7:02 ` [PATCH 05/10] ixp4xx: add gpio support Jean-Christophe PLAGNIOL-VILLARD
` (6 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-04-23 7:02 UTC (permalink / raw)
To: barebox; +Cc: Krzysztof Hałasa
From: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
arch/arm/mach-ixp4xx/devices.c | 35 ++
drivers/net/Kconfig | 8 +
drivers/net/Makefile | 1 +
drivers/net/ixp4xx_eth.c | 699 ++++++++++++++++++++++++++++++++++++++++
4 files changed, 743 insertions(+), 0 deletions(-)
create mode 100644 drivers/net/ixp4xx_eth.c
diff --git a/arch/arm/mach-ixp4xx/devices.c b/arch/arm/mach-ixp4xx/devices.c
index 8a496d1..8fbfd93 100644
--- a/arch/arm/mach-ixp4xx/devices.c
+++ b/arch/arm/mach-ixp4xx/devices.c
@@ -4,6 +4,8 @@
#include <asm/armlinux.h>
#include <asm/io.h>
#include <mach/ixp4xx-regs.h>
+#include <mach/platform.h>
+#include <mach/cpu.h>
#ifdef CONFIG_DRIVER_SERIAL_NS16550
/**
@@ -58,3 +60,36 @@ struct device_d* ixp4xx_add_uart(int id, u32 base)
return NULL;
}
#endif /* CONFIG_DRIVER_SERIAL_NS16550 */
+
+#ifdef CONFIG_DRIVER_NET_IXP4XX_ETH
+struct device_d* ixp4xx_add_eth(int id, struct eth_plat_info *pdata)
+{
+ resource_size_t start;
+
+ switch (id) {
+ case 1:
+ if (!cpu_is_ixp43x()) {
+ /* All MII PHY accesses use NPE-B Ethernet registers */
+ if (!(ixp4xx_read_feature_bits() & IXP4XX_FEATURE_NPEB_ETH0))
+ return NULL;
+ start = (resource_size_t)IXP4XX_EthB_BASE;
+ break;
+ }
+ case 2:
+ if (!(ixp4xx_read_feature_bits() & IXP4XX_FEATURE_NPEC_ETH))
+ return NULL;
+ start = (resource_size_t)IXP4XX_EthC_BASE;
+ break;
+ default:
+ return NULL;
+ }
+
+ return add_generic_device("ixp4xx_eth", id, NULL, start, 0xfff,
+ IORESOURCE_MEM, pdata);
+}
+#else
+struct device_d* ixp4xx_add_eth(int id, struct eth_plat_info *pdata)
+{
+ return NULL;
+}
+#endif /* CONFIG_DRIVER_NET_IXP4XX_ETH */
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 172cc39..47c86dc 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -81,6 +81,14 @@ config DRIVER_NET_MACB
depends on HAS_MACB
select MIIDEV
+config DRIVER_NET_IXP4XX_ETH
+ tristate "Intel IXP4xx Ethernet support"
+ depends on ARCH_IXP4XX && IXP4XX_NPE && IXP4XX_QMGR
+ select MIIDEV
+ help
+ Say Y here if you want to use built-in Ethernet ports
+ on IXP4xx processor.
+
config DRIVER_NET_TAP
bool "tap Ethernet driver"
depends on LINUX
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 34dbee9..9f18270 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -13,3 +13,4 @@ obj-$(CONFIG_MIIDEV) += miidev.o
obj-$(CONFIG_NET_USB) += usb/
obj-$(CONFIG_DRIVER_NET_TSE) += altera_tse.o
obj-$(CONFIG_DRIVER_NET_KS8851_MLL) += ks8851_mll.o
+obj-$(CONFIG_DRIVER_NET_IXP4XX_ETH) += ixp4xx_eth.o
diff --git a/drivers/net/ixp4xx_eth.c b/drivers/net/ixp4xx_eth.c
new file mode 100644
index 0000000..cacb5d1
--- /dev/null
+++ b/drivers/net/ixp4xx_eth.c
@@ -0,0 +1,699 @@
+/*
+ * Intel IXP4xx Ethernet driver for Linux
+ *
+ * Copyright (C) 2007 Krzysztof Halasa <khc at pm.waw.pl>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ *
+ * Ethernet port config (0x00 is not present on IXP42X):
+ *
+ * logical port 0x00 0x10 0x20
+ * NPE 0 (NPE-A) 1 (NPE-B) 2 (NPE-C)
+ * physical port 2 0 1
+ * RX queue (variable) 20 21 22
+ * TX queue 23 24 25
+ * RX-free queue 26 27 28
+ * TX-done queue is always 31, per-port RX queue is configurable
+ *
+ *
+ * Queue entries:
+ * bits 0 -> 1 - NPE ID (RX and TX-done)
+ * bits 0 -> 2 - priority (TX, per 802.1D)
+ * bits 3 -> 4 - port ID (user-set?)
+ * bits 5 -> 31 - physical descriptor address
+ */
+
+#include <common.h>
+#include <init.h>
+#include <malloc.h>
+#include <miidev.h>
+#include <net.h>
+#include <errno.h>
+#include <mach/ixp4xx-regs.h>
+#include <mach/platform.h>
+#include <mach/cpu.h>
+#include <mach/npe.h>
+#include <mach/qmgr.h>
+
+#define DEBUG_DESC 0
+#define DEBUG_RX 0
+#define DEBUG_TX 0
+#define DEBUG_PKT_BYTES 0
+#define DEBUG_MDIO 0
+#define DEBUG_OPEN 0
+#define DEBUG_CLOSE 0
+
+#define RX_DESCS 16 /* also length of all RX queues */
+#define TX_DESCS 16 /* also length of all TX queues */
+#define TXDONE_QUEUE_LEN 16 /* dwords */
+
+#define MAX_MRU 1536 /* 0x600 */
+#define RX_BUFF_SIZE MAX_MRU
+
+#define MAX_MDIO_RETRIES 100 /* microseconds, typically 30 cycles */
+#define MAX_CLOSE_WAIT 1000 /* microseconds, typically 2-3 cycles */
+#define ETH_ALEN 6
+
+#define PHYSICAL_ID(port) (((port)->npe->id + 2) % 3)
+#define LOGICAL_ID(port) ((port)->npe->id << 4)
+#define RX_QUEUE(port) ((port)->npe->id + 20) /* can be changed */
+#define TX_QUEUE(port) ((port)->npe->id + 23)
+#define RXFREE_QUEUE(port) ((port)->npe->id + 26)
+#define TXDONE_QUEUE 31
+
+/* TX Control Registers */
+#define TX_CNTRL0_TX_EN 0x01
+#define TX_CNTRL0_HALFDUPLEX 0x02
+#define TX_CNTRL0_RETRY 0x04
+#define TX_CNTRL0_PAD_EN 0x08
+#define TX_CNTRL0_APPEND_FCS 0x10
+#define TX_CNTRL0_2DEFER 0x20
+#define TX_CNTRL0_RMII 0x40 /* reduced MII */
+#define TX_CNTRL1_RETRIES 0x0F /* 4 bits */
+
+/* RX Control Registers */
+#define RX_CNTRL0_RX_EN 0x01
+#define RX_CNTRL0_PADSTRIP_EN 0x02
+#define RX_CNTRL0_SEND_FCS 0x04
+#define RX_CNTRL0_PAUSE_EN 0x08
+#define RX_CNTRL0_LOOP_EN 0x10
+#define RX_CNTRL0_ADDR_FLTR_EN 0x20
+#define RX_CNTRL0_RX_RUNT_EN 0x40
+#define RX_CNTRL0_BCAST_DIS 0x80
+#define RX_CNTRL1_DEFER_EN 0x01
+
+/* Core Control Register */
+#define CORE_RESET 0x01
+#define CORE_RX_FIFO_FLUSH 0x02
+#define CORE_TX_FIFO_FLUSH 0x04
+#define CORE_SEND_JAM 0x08
+#define CORE_MDC_EN 0x10 /* MDIO using NPE-B ETH-0 only */
+
+#define DEFAULT_TX_CNTRL0 (TX_CNTRL0_TX_EN | TX_CNTRL0_RETRY | \
+ TX_CNTRL0_PAD_EN | TX_CNTRL0_APPEND_FCS | \
+ TX_CNTRL0_2DEFER)
+#define DEFAULT_RX_CNTRL0 RX_CNTRL0_RX_EN
+#define DEFAULT_CORE_CNTRL CORE_MDC_EN
+
+
+/* NPE message codes */
+#define NPE_GETSTATUS 0x00
+#define NPE_EDB_SETPORTADDRESS 0x01
+#define NPE_EDB_GETMACADDRESSDATABASE 0x02
+#define NPE_EDB_SETMACADDRESSSDATABASE 0x03
+#define NPE_GETSTATS 0x04
+#define NPE_RESETSTATS 0x05
+#define NPE_SETMAXFRAMELENGTHS 0x06
+#define NPE_VLAN_SETRXTAGMODE 0x07
+#define NPE_VLAN_SETDEFAULTRXVID 0x08
+#define NPE_VLAN_SETPORTVLANTABLEENTRY 0x09
+#define NPE_VLAN_SETPORTVLANTABLERANGE 0x0A
+#define NPE_VLAN_SETRXQOSENTRY 0x0B
+#define NPE_VLAN_SETPORTIDEXTRACTIONMODE 0x0C
+#define NPE_STP_SETBLOCKINGSTATE 0x0D
+#define NPE_FW_SETFIREWALLMODE 0x0E
+#define NPE_PC_SETFRAMECONTROLDURATIONID 0x0F
+#define NPE_PC_SETAPMACTABLE 0x11
+#define NPE_SETLOOPBACK_MODE 0x12
+#define NPE_PC_SETBSSIDTABLE 0x13
+#define NPE_ADDRESS_FILTER_CONFIG 0x14
+#define NPE_APPENDFCSCONFIG 0x15
+#define NPE_NOTIFY_MAC_RECOVERY_DONE 0x16
+#define NPE_MAC_RECOVERY_START 0x17
+
+struct eth_regs {
+ u32 tx_control[2], __res1[2]; /* 000 */
+ u32 rx_control[2], __res2[2]; /* 010 */
+ u32 random_seed, __res3[3]; /* 020 */
+ u32 partial_empty_threshold, __res4; /* 030 */
+ u32 partial_full_threshold, __res5; /* 038 */
+ u32 tx_start_bytes, __res6[3]; /* 040 */
+ u32 tx_deferral, rx_deferral, __res7[2]; /* 050 */
+ u32 tx_2part_deferral[2], __res8[2]; /* 060 */
+ u32 slot_time, __res9[3]; /* 070 */
+ u32 mdio_command[4]; /* 080 */
+ u32 mdio_status[4]; /* 090 */
+ u32 mcast_mask[6], __res10[2]; /* 0A0 */
+ u32 mcast_addr[6], __res11[2]; /* 0C0 */
+ u32 int_clock_threshold, __res12[3]; /* 0E0 */
+ u32 hw_addr[6], __res13[61]; /* 0F0 */
+ u32 core_control; /* 1FC */
+};
+
+/* NPE message structure */
+struct msg {
+ u8 cmd, eth_id, params[6];
+};
+
+/* Ethernet packet descriptor, 32 bytes */
+struct desc {
+ u8 *next; /* pointer to next buffer, unused */
+
+ u16 buf_len; /* buffer length */
+ u16 pkt_len; /* packet length */
+ u8 *data; /* pointer to data buffer in RAM */
+ u8 dest_id;
+ u8 src_id;
+ u16 flags;
+ u8 qos;
+ u8 padlen;
+ u16 vlan_tci;
+
+ u8 dst_mac[ETH_ALEN], src_mac[ETH_ALEN];
+};
+
+struct port {
+ struct desc rx_desc_tab[RX_DESCS]; /* alignment: 0x10 */
+ struct desc tx_desc_tab[TX_DESCS];
+ u8 *buff_tab;
+ struct eth_regs *regs;
+ struct npe *npe;
+ u8 firmware[4];
+ struct eth_plat_info *pinfo;
+ struct mii_device miidev;
+ struct eth_device eth;
+};
+
+#define rx_buff(port, n) ((port)->buff_tab + MAX_MRU * (n))
+#define tx_buff(port, n) ((port)->buff_tab + MAX_MRU * (RX_DESCS + (n)))
+
+static int ixp4xx_mdio_cmd(const struct mii_device *mii, int write, unsigned char phy_id,
+ unsigned char location, unsigned short value)
+{
+ int cycles = 0;
+ struct port *port = mii->edev->priv;
+ struct eth_regs *mdio_regs = port->regs;
+
+ if (__raw_readl(&mdio_regs->mdio_command[3]) & 0x80) {
+ dev_err(&mii->dev, "MII not ready to transmit\n");
+ return -1;
+ }
+
+ if (write) {
+ __raw_writel(value & 0xFF, &mdio_regs->mdio_command[0]);
+ __raw_writel(value >> 8, &mdio_regs->mdio_command[1]);
+ }
+ __raw_writel(((phy_id << 5) | location) & 0xFF,
+ &mdio_regs->mdio_command[2]);
+ __raw_writel((phy_id >> 3) | (write << 2) | 0x80 /* GO */,
+ &mdio_regs->mdio_command[3]);
+
+ while ((cycles < MAX_MDIO_RETRIES) &&
+ (__raw_readl(&mdio_regs->mdio_command[3]) & 0x80)) {
+ udelay(1);
+ cycles++;
+ }
+
+ if (cycles == MAX_MDIO_RETRIES) {
+ dev_err(&mii->dev, "MII write failed\n");
+ return -1;
+ }
+
+ dev_dbg(&mii->dev, "mdio_%s() took %i cycles\n",
+ write ? "write" : "read", cycles);
+
+ if (write)
+ return 0;
+
+ if (__raw_readl(&mdio_regs->mdio_status[3]) & 0x80) {
+ dev_dbg(&mii->dev, "MII read failed\n");
+ return -1;
+ }
+
+ value = (__raw_readl(&mdio_regs->mdio_status[0]) & 0xFF) |
+ ((__raw_readl(&mdio_regs->mdio_status[1]) & 0xFF) << 8);
+ dev_dbg(&mii->dev, "MII read [%i] -> 0x%X\n", location, value);
+
+ return value;
+}
+
+static int ixp4xx_mdio_read(struct mii_device *mii, int phy_id, int location)
+{
+ int ret = ixp4xx_mdio_cmd(mii, 0, phy_id, location, 0);
+
+ dev_dbg(&mii->dev, "MII read [%i], read = %i\n", location, ret);
+
+ return ret;
+}
+
+static int ixp4xx_mdio_write(struct mii_device *mii, int phy_id, int location, int value)
+{
+ int ret = ixp4xx_mdio_cmd(mii, 1, phy_id, location, value);
+
+ dev_dbg(&mii->dev, "MII write [%i] <- 0x%X, err = %i\n", location, value, ret);
+
+ return ret;
+}
+
+static int ixp4xx_adjust_link(struct eth_device *dev)
+{
+ struct port *port = dev->priv;
+ int status, speed, duplex;
+
+ miidev_wait_aneg(&port->miidev);
+ status = miidev_get_status(&port->miidev);
+
+ duplex = status & MIIDEV_STATUS_IS_FULL_DUPLEX ? 1 : 0;
+ speed = status & MIIDEV_STATUS_IS_100MBIT ? 100 : 10;
+
+ if (status < 0)
+ goto err_out;
+
+ if (duplex)
+ __raw_writel(DEFAULT_TX_CNTRL0 & ~TX_CNTRL0_HALFDUPLEX,
+ &port->regs->tx_control[0]);
+ else
+ __raw_writel(DEFAULT_TX_CNTRL0 | TX_CNTRL0_HALFDUPLEX,
+ &port->regs->tx_control[0]);
+
+ dev_err(&dev->dev, "link up, speed %u Mb/s, %s duplex\n",
+ speed, duplex ? "full" : "half");
+ return 0;
+
+err_out:
+ dev_err(&dev->dev, "failed to read MII data\n");;
+ return status;
+}
+
+#if DEBUG_PKT_BYTES
+static inline void debug_pkt(struct eth_device *dev, const char *func,
+ u8 *data, int len)
+{
+ int i;
+
+ dev_dbg(&dev->dev, "%s(%4i) ", func, len);
+ for (i = 0; i < len; i++) {
+ if (i >= DEBUG_PKT_BYTES)
+ break;
+ dev_dbg(&dev->dev, "%s%02X",
+ ((i == 6) || (i == 12) || (i >= 14)) ? " " : "",
+ data[i]);
+ }
+ dev_dbg(&dev->dev, "\n");
+}
+#else
+static inline void debug_pkt(struct eth_device *dev, const char *func,
+ u8 *data, int len)
+{}
+#endif
+
+#if DEBUG_DESC
+static inline void debug_desc(struct desc *desc)
+{
+ fprintf(stderr, "%07X: %X %3X %3X %07X %2X < %2X %4X %X"
+ " %X %X %02X%02X%02X%02X%02X%02X < %02X%02X%02X%02X%02X%02X\n",
+ (u32)desc, (u32)desc->next, desc->buf_len, desc->pkt_len,
+ (u32)desc->data, desc->dest_id, desc->src_id, desc->flags,
+ desc->qos, desc->padlen, desc->vlan_tci,
+ desc->dst_mac[0], desc->dst_mac[1], desc->dst_mac[2],
+ desc->dst_mac[3], desc->dst_mac[4], desc->dst_mac[5],
+ desc->src_mac[0], desc->src_mac[1], desc->src_mac[2],
+ desc->src_mac[3], desc->src_mac[4], desc->src_mac[5]);
+#else
+static inline void debug_desc(struct desc *desc)
+{
+}
+#endif
+
+static inline int queue_get_desc(unsigned int queue, struct port *port,
+ int is_tx)
+{
+ u32 addr, n;
+ struct desc *tab;
+
+ if (!(addr = qmgr_get_entry(queue)))
+ return -1;
+
+ addr &= ~0x1F; /* mask out non-address bits */
+ tab = is_tx ? port->tx_desc_tab : port->rx_desc_tab;
+ n = (addr - (u32)tab) / sizeof(struct desc);
+ BUG_ON(n >= (is_tx ? TX_DESCS : RX_DESCS));
+ debug_desc((struct desc*)addr);
+ BUG_ON(tab[n].next);
+ return n;
+}
+
+static inline void queue_put_desc(unsigned int queue, struct desc *desc)
+{
+ debug_desc(desc);
+ BUG_ON(((u32)desc) & 0x1F);
+ qmgr_put_entry(queue, (u32)desc);
+ /* Don't check for queue overflow here, we've allocated sufficient
+ length and queues >= 32 don't support this check anyway. */
+}
+
+static int ixp4xx_eth_poll(struct eth_device *dev)
+{
+ struct port *port = dev->priv;
+ struct desc *desc;
+ u8 *buff;
+ int n, len;
+
+ dev_dbg(&dev->dev, "eth_poll\n");
+
+ if ((n = queue_get_desc(RX_QUEUE(port), port, 0)) < 0) {
+ dev_dbg(&dev->dev, "eth_poll = no packet receive\n");
+ return 0;
+ }
+
+ barrier();
+ desc = &port->rx_desc_tab[n];
+ buff = rx_buff(port, n);
+ len = desc->pkt_len;
+ /* process received frame */
+ memcpy((void *)NetRxPackets[0], buff, len);
+ debug_pkt(dev, "RX", desc->data, len);
+
+ /* put the new buffer on RX-free queue */
+ desc->buf_len = MAX_MRU;
+ desc->pkt_len = 0;
+ queue_put_desc(RXFREE_QUEUE(port), desc);
+
+ net_receive(NetRxPackets[0], len);
+
+ dev_dbg(&dev->dev, "eth_poll end\n");
+ return 0;
+}
+
+
+static int ixp4xx_eth_xmit(struct eth_device *dev, void *data, int len)
+{
+ struct port *port = dev->priv;
+ int n;
+ struct desc *desc;
+
+ dev_dbg(&dev->dev, "%s\n", __func__);
+
+ if (unlikely(len > 1500))
+ return -1;
+
+ debug_pkt(dev, "TX", data, len);
+
+ if ((n = queue_get_desc(TXDONE_QUEUE, port, 1)) < 0)
+ return -1; /* no free buffers */
+ desc = &port->tx_desc_tab[n];
+ desc->data = tx_buff(port, n);
+ desc->buf_len = desc->pkt_len = len;
+ memcpy(desc->data, data, len);
+
+ /* NPE firmware pads short frames with zeros internally */
+ // wmb();
+ barrier();
+ queue_put_desc(TX_QUEUE(port), desc);
+
+ dev_dbg(&dev->dev, "%s end\n", __func__);
+ return 0;
+}
+
+static void request_queues(struct port *port, struct eth_device *dev)
+{
+ qmgr_request_queue(RXFREE_QUEUE(port), RX_DESCS, 0, 0, "%s:RX-free", dev->dev.name);
+ qmgr_request_queue(RX_QUEUE(port), RX_DESCS, 0, 0, "%s:RX", dev->dev.name);
+ qmgr_request_queue(TX_QUEUE(port), TX_DESCS, 0, 0, "%s:TX", dev->dev.name);
+
+ /* Common TX-done queue handles buffers sent out by the NPEs */
+ qmgr_request_queue(TXDONE_QUEUE, TXDONE_QUEUE_LEN, 0, 0,
+ "%s:TX-done", dev->dev.name);
+}
+
+static void release_queues(struct port *port)
+{
+ qmgr_release_queue(RXFREE_QUEUE(port));
+ qmgr_release_queue(RX_QUEUE(port));
+ qmgr_release_queue(TX_QUEUE(port));
+ qmgr_release_queue(TXDONE_QUEUE);
+}
+
+static void init_queues(struct port *port)
+{
+ int i;
+
+ memset(port->tx_desc_tab, 0, sizeof(port->tx_desc_tab)); /* descs */
+ memset(port->rx_desc_tab, 0, sizeof(port->rx_desc_tab));
+
+ /* Setup RX buffers */
+ for (i = 0; i < RX_DESCS; i++) {
+ struct desc *desc = &port->rx_desc_tab[i];
+ desc->buf_len = MAX_MRU;
+ desc->data = rx_buff(port, i);
+ }
+}
+
+static int ixp4xx_eth_open(struct eth_device *dev)
+{
+ struct port *port = dev->priv;
+ struct npe *npe = port->npe;
+ struct msg msg;
+ int i, err;
+
+ dev_dbg(&dev->dev, "%s\n", __func__);
+
+ if (!npe_running(npe)) {
+ err = npe_load_firmware(npe);
+ if (err)
+ return err;
+
+ if (npe_recv_message(npe, &msg, "ETH_GET_STATUS")) {
+ dev_err(&dev->dev, " %s not responding\n", npe->name);
+ return -EIO;
+ }
+ memcpy(port->firmware, msg.params + 2, 4);
+ }
+
+ err = ixp4xx_adjust_link(dev);
+ if (err)
+ return err;
+
+ port->buff_tab = xmalloc((RX_DESCS + TX_DESCS) * MAX_MRU);
+
+ memset(&msg, 0, sizeof(msg));
+ msg.cmd = NPE_VLAN_SETRXQOSENTRY;
+ msg.eth_id = LOGICAL_ID(port);
+ msg.params[3] = RX_QUEUE(port) | 0x80;
+ msg.params[4] = RX_QUEUE(port) >> 4; /* MSB of offset */
+ msg.params[5] = RX_QUEUE(port) << 4; /* LSB of offset */
+ for (i = 0; i < 8; i++) {
+ msg.params[1] = i;
+ if (npe_send_recv_message(port->npe, &msg, "ETH_SET_RXQ")) {
+ err = -EIO;
+ goto out;
+ }
+ }
+
+ msg.cmd = NPE_EDB_SETPORTADDRESS;
+ msg.eth_id = PHYSICAL_ID(port);
+ memcpy(msg.params, port->pinfo->hwaddr, ETH_ALEN);
+ if (npe_send_recv_message(port->npe, &msg, "ETH_SET_MAC")) {
+ err = -EIO;
+ goto out;
+ }
+
+ memset(&msg, 0, sizeof(msg));
+ msg.cmd = NPE_FW_SETFIREWALLMODE;
+ msg.eth_id = LOGICAL_ID(port);
+ if (npe_send_recv_message(port->npe, &msg, "ETH_SET_FIREWALL_MODE")) {
+ err = -EIO;
+ goto out;
+ }
+
+ request_queues(port, dev);
+ init_queues(port);
+
+ for (i = 0; i < ETH_ALEN; i++)
+ __raw_writel(port->pinfo->hwaddr[i], &port->regs->hw_addr[i]);
+ __raw_writel(0x08, &port->regs->random_seed);
+ __raw_writel(0x12, &port->regs->partial_empty_threshold);
+ __raw_writel(0x30, &port->regs->partial_full_threshold);
+ __raw_writel(0x08, &port->regs->tx_start_bytes);
+ __raw_writel(0x15, &port->regs->tx_deferral);
+ __raw_writel(0x08, &port->regs->tx_2part_deferral[0]);
+ __raw_writel(0x07, &port->regs->tx_2part_deferral[1]);
+ __raw_writel(0x80, &port->regs->slot_time);
+ __raw_writel(0x01, &port->regs->int_clock_threshold);
+
+ /* Populate queues with buffers, no failure after this point */
+ for (i = 0; i < TX_DESCS; i++)
+ queue_put_desc(TXDONE_QUEUE, &port->tx_desc_tab[i]);
+
+ for (i = 0; i < RX_DESCS; i++)
+ queue_put_desc(RXFREE_QUEUE(port), &port->rx_desc_tab[i]);
+
+ __raw_writel(TX_CNTRL1_RETRIES, &port->regs->tx_control[1]);
+ __raw_writel(DEFAULT_TX_CNTRL0, &port->regs->tx_control[0]);
+ __raw_writel(0, &port->regs->rx_control[1]);
+ __raw_writel(DEFAULT_RX_CNTRL0, &port->regs->rx_control[0]);
+
+ memset(&msg, 0, sizeof(msg));
+ dev_dbg(&dev->dev, "%s opened\n", __func__);
+ return 0;
+out:
+ free(port->buff_tab);
+ port->buff_tab = NULL;
+ dev_dbg(&dev->dev, "%s open failed (%i)\n", __func__, err);
+ return err;
+}
+
+static void ixp4xx_eth_close(struct eth_device *dev)
+{
+ struct port *port = dev->priv;
+ struct msg msg;
+ int buffs = RX_DESCS; /* allocated RX buffers */
+ int i;
+
+ dev_dbg(&dev->dev, "%s\n", __func__);
+
+ if (!port->buff_tab)
+ return; /* already closed */
+
+ while (queue_get_desc(RXFREE_QUEUE(port), port, 0) >= 0)
+ buffs--;
+
+ memset(&msg, 0, sizeof(msg));
+ msg.cmd = NPE_SETLOOPBACK_MODE;
+ msg.eth_id = LOGICAL_ID(port);
+ msg.params[1] = 1;
+ if (npe_send_recv_message(port->npe, &msg, "ETH_ENABLE_LOOPBACK"))
+ fprintf(stderr, "%s%d: unable to enable loopback\n", dev->dev.name, dev->dev.id);
+
+ dev_dbg(&dev->dev, "%s: draining RX queue\n", __func__);
+ i = 0;
+ do { /* drain RX buffers */
+ while (queue_get_desc(RX_QUEUE(port), port, 0) >= 0)
+ buffs--;
+ if (!buffs)
+ break;
+ if (qmgr_stat_full(TXDONE_QUEUE) && !(i % 10)) {
+ /* we have to inject some packet */
+ struct desc *desc;
+ int n = queue_get_desc(TXDONE_QUEUE, port, 1);
+ BUG_ON(n < 0);
+ desc = &port->tx_desc_tab[n];
+ desc->buf_len = desc->pkt_len = 1;
+ //wmb();
+ barrier();
+ queue_put_desc(TX_QUEUE(port), desc);
+ }
+ udelay(1);
+ } while (++i < MAX_CLOSE_WAIT);
+
+ if (buffs)
+ fprintf(stderr, "%s%d: unable to drain RX queue, %i buffer(s) left in NPE\n",
+ dev->dev.name, dev->dev.id, buffs);
+ if (!buffs)
+ dev_dbg(&dev->dev, "%s: draining RX queue took %i cycles\n", __func__, i);
+
+ buffs = TX_DESCS;
+ while (queue_get_desc(TX_QUEUE(port), port, 1) >= 0)
+ buffs--; /* cancel TX */
+
+ i = 0;
+ do {
+ while (queue_get_desc(TXDONE_QUEUE, port, 1) >= 0)
+ buffs--;
+ if (!buffs)
+ break;
+ } while (++i < MAX_CLOSE_WAIT);
+
+ if (buffs)
+ fprintf(stderr, "%s%d: unable to drain TX queue, %i buffer(s) left in NPE\n",
+ dev->dev.name, dev->dev.id, buffs);
+ if (!buffs)
+ dev_dbg(&dev->dev, "%s: draining TX queue took %i cycles\n", __func__, i);
+
+ msg.params[1] = 0;
+ if (npe_send_recv_message(port->npe, &msg, "ETH_DISABLE_LOOPBACK"))
+ fprintf(stderr, "%s%d: unable to disable loopback\n", dev->dev.name, dev->dev.id);
+
+ release_queues(port);
+ free(port->buff_tab);
+ port->buff_tab = NULL;
+ dev_dbg(&dev->dev, "%s: closed\n", __func__);
+}
+
+static int ixp4xx_eth_get_hwaddr(struct eth_device *eth, unsigned char *addr)
+{
+ struct port *port = eth->priv;
+ memcpy(addr, port->pinfo->hwaddr, 6);
+ return 0;
+}
+
+static int ixp4xx_eth_set_hwaddr(struct eth_device *eth, unsigned char *addr)
+{
+ struct port *port = eth->priv;
+ memcpy(port->pinfo->hwaddr, addr, 6);
+ return 0;
+}
+
+static int ixp4xx_eth_init(struct eth_device *eth)
+{
+ struct port *port = eth->priv;
+
+ __raw_writel(DEFAULT_CORE_CNTRL | CORE_RESET,
+ &port->regs->core_control);
+ udelay(50);
+ __raw_writel(DEFAULT_CORE_CNTRL, &port->regs->core_control);
+ udelay(50);
+
+ miidev_restart_aneg(&port->miidev);
+ return 0;
+}
+
+static int ixp4xx_eth_probe(struct device_d *dev)
+{
+ struct npe *npe;
+ struct port *port;
+ struct eth_plat_info *pinfo = dev->platform_data;
+ struct eth_regs *mdio_regs;
+
+ if (!pinfo) {
+ dev_err(dev, "ixp4xx_eth: no platform information\n");
+ return -ENODEV;
+ }
+
+ mdio_regs = dev_request_mem_region(dev, 0);
+ __raw_writel(DEFAULT_CORE_CNTRL, &mdio_regs->core_control);
+
+ if (!(npe = npe_request(pinfo->npe))) {
+ dev_err(dev, "ixp4xx_eth: unable to acquire NPE\n");
+ return -ENODEV;
+ }
+
+ port = xmemalign(0x20, sizeof(*port));
+ memset(port, 0, sizeof(*port));
+
+ port->regs = mdio_regs;
+ port->npe = npe;
+ port->pinfo = pinfo;
+ port->eth.dev.id = -1;
+ port->eth.priv = port;
+ port->eth.init = ixp4xx_eth_init;
+ port->eth.open = ixp4xx_eth_open;
+ port->eth.halt = ixp4xx_eth_close;
+ port->eth.send = ixp4xx_eth_xmit;
+ port->eth.recv = ixp4xx_eth_poll;
+ port->eth.get_ethaddr = ixp4xx_eth_get_hwaddr;
+ port->eth.set_ethaddr = ixp4xx_eth_set_hwaddr;
+ port->eth.parent = dev;
+
+ port->miidev.dev.id = -1;
+ port->miidev.read = ixp4xx_mdio_read;
+ port->miidev.write = ixp4xx_mdio_write;
+ port->miidev.address = pinfo->phy;
+ port->miidev.edev = &port->eth;
+ mii_register(&port->miidev);
+ eth_register(&port->eth);
+ return 0;
+}
+
+static struct driver_d ixp4xx_eth_driver = {
+ .name = "ixp4xx_eth",
+ .probe = ixp4xx_eth_probe,
+};
+
+static int __init ixp4xx_eth_module_init(void)
+{
+ return register_driver(&ixp4xx_eth_driver);
+}
+device_initcall(ixp4xx_eth_module_init);
--
1.7.9.1
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* [PATCH 05/10] ixp4xx: add gpio support
2012-04-23 6:56 [PATCH 00/10] IXP4xx rebase WIP Jean-Christophe PLAGNIOL-VILLARD
` (3 preceding siblings ...)
2012-04-23 7:02 ` [PATCH 04/10] net: Add support for IXP4xx ethernet support Jean-Christophe PLAGNIOL-VILLARD
@ 2012-04-23 7:02 ` Jean-Christophe PLAGNIOL-VILLARD
2012-04-23 7:02 ` [PATCH 06/10] ixp4xx: add generic board lowlevel_init Jean-Christophe PLAGNIOL-VILLARD
` (5 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-04-23 7:02 UTC (permalink / raw)
To: barebox
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
arch/arm/Kconfig | 1 +
arch/arm/mach-ixp4xx/include/mach/gpio.h | 69 +++++++++++++++++++++++
arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h | 2 +-
arch/arm/mach-ixp4xx/include/mach/platform.h | 46 +++++++++++++++
4 files changed, 117 insertions(+), 1 deletions(-)
create mode 100644 arch/arm/mach-ixp4xx/include/mach/gpio.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 2cc3f2d..7549ea5 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -51,6 +51,7 @@ config ARCH_MXS
config ARCH_IXP4XX
bool "Intel IXP4xx-based"
+ select GENERIC_GPIO
select CPU_XSCALE
select ARCH_SUPPORTS_BIG_ENDIAN
select CPU_BIG_ENDIAN
diff --git a/arch/arm/mach-ixp4xx/include/mach/gpio.h b/arch/arm/mach-ixp4xx/include/mach/gpio.h
new file mode 100644
index 0000000..415ff56
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/include/mach/gpio.h
@@ -0,0 +1,69 @@
+/*
+ * arch/arm/mach-ixp4xx/include/mach/gpio.h
+ *
+ * IXP4XX GPIO wrappers for arch-neutral GPIO calls
+ *
+ * Written by Milan Svoboda <msvoboda@ra.rockwell.com>
+ * Based on PXA implementation by Philipp Zabel <philipp.zabel@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+
+#ifndef __ASM_ARCH_IXP4XX_GPIO_H
+#define __ASM_ARCH_IXP4XX_GPIO_H
+
+#include <linux/kernel.h>
+#include <mach/ixp4xx-regs.h>
+#include <mach/platform.h>
+
+static inline int gpio_request(unsigned gpio, const char *label)
+{
+ return 0;
+}
+
+static inline void gpio_free(unsigned gpio)
+{
+ return;
+}
+
+static inline int gpio_direction_input(unsigned gpio)
+{
+ gpio_line_config(gpio, IXP4XX_GPIO_IN);
+ return 0;
+}
+
+static inline int gpio_direction_output(unsigned gpio, int level)
+{
+ gpio_line_set(gpio, level);
+ gpio_line_config(gpio, IXP4XX_GPIO_OUT);
+ return 0;
+}
+
+static inline int gpio_get_value(unsigned gpio)
+{
+ int value;
+
+ gpio_line_get(gpio, &value);
+
+ return value;
+}
+
+static inline void gpio_set_value(unsigned gpio, int value)
+{
+ gpio_line_set(gpio, value);
+}
+
+#endif
diff --git a/arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h b/arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h
index da4dc8a..3ee88e7 100644
--- a/arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h
+++ b/arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h
@@ -84,7 +84,7 @@
#define IXP4XX_UART2_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0x1000)
#define IXP4XX_PMU_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0x2000)
#define IXP4XX_INTC_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0x3000)
-#define IXP4XX_GPIO_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0x4000)
+#define IXP4XX_GPIO_BASE IXP4XX_PERIPHERAL_BASE + 0x4000
#define IXP4XX_NPEA_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0x6000)
#define IXP4XX_NPEB_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0x7000)
#define IXP4XX_NPEC_BASE IXP4XX_BASE(IXP4XX_PERIPHERAL_BASE + 0x8000)
diff --git a/arch/arm/mach-ixp4xx/include/mach/platform.h b/arch/arm/mach-ixp4xx/include/mach/platform.h
index bff9185..8f71d66 100644
--- a/arch/arm/mach-ixp4xx/include/mach/platform.h
+++ b/arch/arm/mach-ixp4xx/include/mach/platform.h
@@ -23,6 +23,52 @@ struct eth_plat_info {
u8 hwaddr[6];
};
+/*
+ * GPIO-functions
+ */
+/*
+ * The following converted to the real HW bits the gpio_line_config
+ */
+/* GPIO pin types */
+#define IXP4XX_GPIO_OUT 0x1
+#define IXP4XX_GPIO_IN 0x2
+
+/* GPIO signal types */
+#define IXP4XX_GPIO_LOW 0
+#define IXP4XX_GPIO_HIGH 1
+
+/* GPIO Clocks */
+#define IXP4XX_GPIO_CLK_0 14
+#define IXP4XX_GPIO_CLK_1 15
+
+static inline void gpio_line_config(u8 line, u32 direction)
+{
+ if (direction == IXP4XX_GPIO_IN)
+ *IXP4XX_GPIO_GPOER |= (1 << line);
+ else
+ *IXP4XX_GPIO_GPOER &= ~(1 << line);
+}
+
+static inline void gpio_line_get(u8 line, int *value)
+{
+ *value = (*IXP4XX_GPIO_GPINR >> line) & 0x1;
+}
+
+static inline void gpio_line_set(u8 line, int value)
+{
+ if (value == IXP4XX_GPIO_HIGH)
+ *IXP4XX_GPIO_GPOUTR |= (1 << line);
+ else if (value == IXP4XX_GPIO_LOW)
+ *IXP4XX_GPIO_GPOUTR &= ~(1 << line);
+}
+
+static inline void gpio_int_act_low_set(u8 line)
+{
+ u32 val = *IXP4XX_GPIO_GPIT1R;
+
+ *IXP4XX_GPIO_GPIT1R = (val & ~(0x7 << (line * 3))) | (0x1 << (line * 3));
+}
+
struct device_d* ixp4xx_add_uart(int id, u32 base);
static inline struct device_d* ixp4xx_add_uart1(void)
--
1.7.9.1
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* [PATCH 06/10] ixp4xx: add generic board lowlevel_init
2012-04-23 6:56 [PATCH 00/10] IXP4xx rebase WIP Jean-Christophe PLAGNIOL-VILLARD
` (4 preceding siblings ...)
2012-04-23 7:02 ` [PATCH 05/10] ixp4xx: add gpio support Jean-Christophe PLAGNIOL-VILLARD
@ 2012-04-23 7:02 ` Jean-Christophe PLAGNIOL-VILLARD
2012-04-23 7:02 ` [PATCH 07/10] ARM: Add support for Linksys NSLU2 support Jean-Christophe PLAGNIOL-VILLARD
` (4 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-04-23 7:02 UTC (permalink / raw)
To: barebox
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
arch/arm/mach-ixp4xx/Kconfig | 3 +
arch/arm/mach-ixp4xx/Makefile | 2 +
arch/arm/mach-ixp4xx/board_lowlevel_init.c | 56 ++++++++++++++++++++++++++++
3 files changed, 61 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/mach-ixp4xx/board_lowlevel_init.c
diff --git a/arch/arm/mach-ixp4xx/Kconfig b/arch/arm/mach-ixp4xx/Kconfig
index d92832c..f9388bf 100644
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -1,5 +1,8 @@
if ARCH_IXP4XX
+config IXP4XX_GENERIC_LOWLEVEL_INIT
+ bool
+
choice
prompt "IXP4xx Board Type"
diff --git a/arch/arm/mach-ixp4xx/Makefile b/arch/arm/mach-ixp4xx/Makefile
index 9bb2e99..958de5e 100644
--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
@@ -4,3 +4,5 @@ obj-y += timer.o
obj-y += reset.o
obj-$(CONFIG_IXP4XX_QMGR) += qmgr.o
obj-$(CONFIG_IXP4XX_NPE) += npe.o
+arch_board_lowlevel_init-$(CONFIG_IXP4XX_GENERIC_LOWLEVEL_INIT) = board_lowlevel_init.o
+obj-$(CONFIG_MACH_HAS_LOWLEVEL_INIT) += $(arch_board_lowlevel_init-y)
diff --git a/arch/arm/mach-ixp4xx/board_lowlevel_init.c b/arch/arm/mach-ixp4xx/board_lowlevel_init.c
new file mode 100644
index 0000000..061246d
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/board_lowlevel_init.c
@@ -0,0 +1,56 @@
+/*
+ * Copyright (C) 2011 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Under GPLv2
+ */
+
+#include <common.h>
+#include <init.h>
+#include <asm/barebox-arm.h>
+#include <asm/io.h>
+#include <asm/system.h>
+#include <mach/ixp4xx-regs.h>
+
+static void inline delay(int x)
+{
+ while (x-- > 0)
+ barrier();
+}
+
+void __naked __bare_init board_init_lowlevel(void)
+{
+ int i;
+
+ IXP4XX_SDRAM_CONFIG = CONFIG_SDRAM_CONFIG;
+
+ /* disable refresh cycles */
+ IXP4XX_SDRAM_REFRESH = 0x0;
+
+ /* send NOP command */
+ IXP4XX_SDRAM_IR = 0x3;
+ delay(0x4000);
+
+ /* set SDRAM internal refresh */
+ IXP4XX_SDRAM_REFRESH = CONFIG_SDRAM_REFRESH;
+ delay(0x4000);
+
+ /* send precharge-all command to close all open banks */
+ IXP4XX_SDRAM_IR = 0x2;
+ delay(0x4000);
+
+ /* provide 8 auto-refresh cycles */
+ for (i = 0; i < 8; i++) {
+ IXP4XX_SDRAM_IR = 0x4;
+ delay(0x100);
+ }
+
+ /* set mode register in SDRAM */
+ IXP4XX_SDRAM_IR = CONFIG_SDRAM_MODE;
+ delay(0x4000);
+
+ /* send normal operation command */
+ IXP4XX_SDRAM_IR = 0x6;
+ delay(0x4000);
+
+ board_init_lowlevel_return();
+}
--
1.7.9.1
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* [PATCH 07/10] ARM: Add support for Linksys NSLU2 support
2012-04-23 6:56 [PATCH 00/10] IXP4xx rebase WIP Jean-Christophe PLAGNIOL-VILLARD
` (5 preceding siblings ...)
2012-04-23 7:02 ` [PATCH 06/10] ixp4xx: add generic board lowlevel_init Jean-Christophe PLAGNIOL-VILLARD
@ 2012-04-23 7:02 ` Jean-Christophe PLAGNIOL-VILLARD
2012-04-23 7:02 ` [PATCH 08/10] ARM: Add support for Goramo Multilink router platform Jean-Christophe PLAGNIOL-VILLARD
` (3 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-04-23 7:02 UTC (permalink / raw)
To: barebox
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
arch/arm/Makefile | 1 +
arch/arm/boards/nslu2/Makefile | 1 +
arch/arm/boards/nslu2/config.h | 6 +
arch/arm/boards/nslu2/env/config | 36 ++++++
arch/arm/boards/nslu2/init.c | 171 ++++++++++++++++++++++++++++
arch/arm/configs/nslu2_defconfig | 65 +++++++++++
arch/arm/cpu/Kconfig | 6 +-
arch/arm/mach-ixp4xx/Kconfig | 12 ++
arch/arm/mach-ixp4xx/board_lowlevel_init.c | 4 +-
9 files changed, 300 insertions(+), 2 deletions(-)
create mode 100644 arch/arm/boards/nslu2/Makefile
create mode 100644 arch/arm/boards/nslu2/config.h
create mode 100644 arch/arm/boards/nslu2/env/config
create mode 100644 arch/arm/boards/nslu2/init.c
create mode 100644 arch/arm/configs/nslu2_defconfig
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index cc5223e..34abd19 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -97,6 +97,7 @@ board-$(CONFIG_MACH_MMCCPU) := mmccpu
board-$(CONFIG_MACH_MX1ADS) := mx1ads
board-$(CONFIG_MACH_NOMADIK_8815NHK) := nhk8815
board-$(CONFIG_MACH_NXDB500) := netx
+board-$(CONFIG_MACH_NSLU2) := nslu2
board-$(CONFIG_MACH_OMAP343xSDP) := omap343xdsp
board-$(CONFIG_MACH_BEAGLE) := beagle
board-$(CONFIG_MACH_OMAP3EVM) := omap3evm
diff --git a/arch/arm/boards/nslu2/Makefile b/arch/arm/boards/nslu2/Makefile
new file mode 100644
index 0000000..eb072c0
--- /dev/null
+++ b/arch/arm/boards/nslu2/Makefile
@@ -0,0 +1 @@
+obj-y += init.o
diff --git a/arch/arm/boards/nslu2/config.h b/arch/arm/boards/nslu2/config.h
new file mode 100644
index 0000000..279d0bc
--- /dev/null
+++ b/arch/arm/boards/nslu2/config.h
@@ -0,0 +1,6 @@
+/*
+ * SDRAM settings
+ */
+#define CONFIG_SDRAM_CONFIG 0x18
+#define CONFIG_SDRAM_MODE 0x1
+#define CONFIG_SDRAM_REFRESH 0x81a
diff --git a/arch/arm/boards/nslu2/env/config b/arch/arm/boards/nslu2/env/config
new file mode 100644
index 0000000..3a6eaa2
--- /dev/null
+++ b/arch/arm/boards/nslu2/env/config
@@ -0,0 +1,36 @@
+#!/bin/sh
+
+# use 'dhcp' to do dhcp in barebox and in kernel
+# use 'none' if you want to skip kernel ip autoconfiguration
+ip=dhcp-barebox
+dhcp_vendor_id=barebox-nslu2
+
+# or set your networking parameters here
+#eth0.ipaddr=a.b.c.d
+#eth0.netmask=a.b.c.d
+#eth0.gateway=a.b.c.d
+#eth0.serverip=a.b.c.d
+
+# can be either 'nfs', 'tftp' or 'nor'
+kernel_loc=nfs
+# can be either 'net', 'nor' or 'initrd'
+rootfs_loc=net
+
+# can be either 'jffs2' or 'ubifs'
+rootfs_type=ubifs
+rootfsimage=root.$rootfs_type
+
+kernelimage=zImage
+#kernelimage=uImage
+#kernelimage=Image
+#kernelimage=Image.lzo
+
+nor_parts="256k(barebox)ro,64k(bareboxenv),1536k(kernel),-(root)"
+rootfs_mtdblock_nor=3
+
+autoboot_timeout=3
+
+bootargs="console=ttyS0,115200"
+
+# set a fancy prompt (if support is compiled in)
+PS1="\e[1;32mbarebox@\e[1;31m\h:\w\e[0m\n# "
diff --git a/arch/arm/boards/nslu2/init.c b/arch/arm/boards/nslu2/init.c
new file mode 100644
index 0000000..dc594fb
--- /dev/null
+++ b/arch/arm/boards/nslu2/init.c
@@ -0,0 +1,171 @@
+//#define DEBUG
+#include <common.h>
+#include <errno.h>
+#include <init.h>
+#include <linux/types.h>
+#include <asm/armlinux.h>
+#include <asm/io.h>
+#include <generated/mach-types.h>
+#include <mach/ixp4xx-regs.h>
+#include <mach/platform.h>
+#include <sizes.h>
+#include <led.h>
+#include <gpio.h>
+
+
+/* LEDs */
+#define NSLU2_LED_RED_GPIO 0
+#define NSLU2_LED_GRN_GPIO 1
+#define NSLU2_LED_DISK1_GPIO 3
+#define NSLU2_LED_DISK2_GPIO 2
+
+#ifdef CONFIG_LED_GPIO
+struct gpio_led leds[] = {
+ {
+ .gpio = NSLU2_LED_GRN_GPIO,
+ .led = {
+ .name = "nslu2:green:ready",
+ },
+ }, {
+ .gpio = NSLU2_LED_RED_GPIO,
+ .led = {
+ .name = "nslu2:red:status",
+ },
+ }, {
+ .gpio = NSLU2_LED_DISK1_GPIO,
+ .active_low = true,
+ .led = {
+ .name = "nslu2:green:disk-1",
+ },
+ }, {
+ .gpio = NSLU2_LED_DISK2_GPIO,
+ .active_low = true,
+ .led = {
+ .name = "nslu2:green:disk-2",
+ },
+ },
+};
+
+static void nslu2_leds_init(void)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(leds); i++)
+ led_gpio_register(&leds[i]);
+ led_set_trigger(LED_TRIGGER_HEARTBEAT, &leds[0].led);
+}
+#else
+static void nslu2_leds_init(void) {}
+#endif
+
+#ifdef CONFIG_DRIVER_NET_IXP4XX_ETH
+static struct eth_plat_info eth_pinfo = {
+ .npe = 1,
+ .phy = 1,
+ .rxq = 20,
+ .txreadyq = 29,
+};
+
+static void nslu2_eth_init(void)
+{
+ int i;
+ u32 f;
+
+ /*
+ * Map in a portion of the flash and read the MAC address.
+ * Since it is stored in BE in the flash itself, we need to
+ * byteswap it if we're in LE mode.
+ */
+ f = IXP4XX_EXP_BASE(0);
+ for (i = 0; i < 6; i++)
+#ifdef __ARMEB__
+ eth_pinfo.hwaddr[i] = readb(f + 0x3FFB0 + i);
+#else
+ eth_pinfo.hwaddr[i] = readb(f + 0x3FFB0 + (i^3));
+#endif
+
+ ixp4xx_add_eth(1, ð_pinfo);
+}
+#else
+static void nslu2_eth_init(void) {}
+#endif
+
+static int nslu2_mem_init(void)
+{
+ arm_add_mem_device("ram0", 0x00000000, SZ_32M);
+
+ return 0;
+}
+mem_initcall(nslu2_mem_init);
+
+static inline u8 __init flash_readb(u32 addr)
+{
+ return __raw_readb(IXP4XX_EXP_BASE(0) + addr);
+}
+
+static int __init nslu2_devices_init(void)
+{
+ IXP4XX_EXP_CS0 = IXP4XX_EXP_WR_EN | IXP4XX_EXP_BYTE_RD16 |
+ IXP4XX_EXP_EN | IXP4XX_EXP_BITS(24) |
+ IXP4XX_EXP_T1(3) | IXP4XX_EXP_T2(3) | IXP4XX_EXP_T3(3) |
+ IXP4XX_EXP_T4(1) | IXP4XX_EXP_T5(2);
+
+ add_cfi_flash_device(0, IXP4XX_EXP_BASE(0), SZ_8M, 0);
+
+ devfs_add_partition("nor0", 0x0, SZ_256K,
+ DEVFS_PARTITION_FIXED | DEVFS_PARTITION_READONLY, "barebox");
+ devfs_add_partition("nor0", SZ_256K, SZ_256K,
+ DEVFS_PARTITION_FIXED, "env0");
+
+ nslu2_eth_init();
+ nslu2_leds_init();
+
+/*
+ * GPIO settings
+ */
+#define GPIO_BUZZER 4
+#define GPIO_POWERBUTTON 5
+#define GPIO_I2C_SCL 6
+#define GPIO_I2C_SDA 7
+#define GPIO_POWEROFF 8
+#define GPIO_PCI_INTC 9
+#define GPIO_PCI_INTB 10
+#define GPIO_PCI_INTA 11
+#define GPIO_RESSETBUTTOM 12
+#define GPIO_PCI_RESET 13
+#define GPIO_EXTBUS_CLK 14
+
+ /*
+ * Setup GPIO's for PCI INTA & INTB & INTC
+ */
+ gpio_direction_input(GPIO_PCI_INTA);
+ gpio_int_act_low_set(GPIO_PCI_INTA);
+ gpio_direction_input(GPIO_PCI_INTB);
+ gpio_int_act_low_set(GPIO_PCI_INTB);
+ gpio_direction_input(GPIO_PCI_INTC);
+ gpio_int_act_low_set(GPIO_PCI_INTC);
+
+ gpio_direction_input(GPIO_RESSETBUTTOM);
+ gpio_direction_input(GPIO_POWERBUTTON);
+
+ /*
+ * Setup GPIO's for 33MHz clock output
+ */
+ *IXP4XX_GPIO_GPCLKR = 0x01FF01FF;
+ gpio_direction_output(GPIO_PCI_RESET, IXP4XX_GPIO_HIGH);
+ gpio_line_config(GPIO_EXTBUS_CLK, IXP4XX_GPIO_OUT);
+
+ armlinux_set_bootparams((void *)(0x00000100));
+ armlinux_set_architecture(MACH_TYPE_NSLU2);
+
+ return 0;
+}
+device_initcall(nslu2_devices_init);
+
+static int nslu2_console_init(void)
+{
+ ixp4xx_add_uart1();
+ ixp4xx_add_uart2();
+ return 0;
+}
+console_initcall(nslu2_console_init);
diff --git a/arch/arm/configs/nslu2_defconfig b/arch/arm/configs/nslu2_defconfig
new file mode 100644
index 0000000..7a1a43b
--- /dev/null
+++ b/arch/arm/configs/nslu2_defconfig
@@ -0,0 +1,65 @@
+CONFIG_ARCH_IXP4XX=y
+CONFIG_BOOT_ENDIANNESS_SWITCH=y
+CONFIG_MACH_NSLU2=y
+CONFIG_IXP4XX_QMGR=y
+CONFIG_IXP4XX_NPE=y
+CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y
+# CONFIG_ARM_EXCEPTIONS is not set
+CONFIG_EXPERIMENTAL=y
+# CONFIG_MACH_DO_LOWLEVEL_INIT is not set
+CONFIG_LONGHELP=y
+CONFIG_GLOB=y
+CONFIG_PROMPT_HUSH_PS2="mgl# "
+CONFIG_HUSH_FANCY_PROMPT=y
+CONFIG_CMDLINE_EDITING=y
+CONFIG_AUTO_COMPLETE=y
+CONFIG_MENU=y
+# CONFIG_CONSOLE_ACTIVATE_FIRST is not set
+CONFIG_CONSOLE_ACTIVATE_ALL=y
+CONFIG_PARTITION=y
+CONFIG_DEFAULT_ENVIRONMENT_GENERIC=y
+CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/nslu2/env"
+CONFIG_DEBUG_INFO=y
+CONFIG_CMD_EDIT=y
+CONFIG_CMD_SLEEP=y
+CONFIG_CMD_SAVEENV=y
+CONFIG_CMD_EXPORT=y
+CONFIG_CMD_PRINTENV=y
+CONFIG_CMD_READLINE=y
+CONFIG_CMD_MENU=y
+CONFIG_CMD_MENU_MANAGEMENT=y
+CONFIG_CMD_PASSWD=y
+CONFIG_CMD_ECHO_E=y
+CONFIG_CMD_LOADB=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_MTEST=y
+CONFIG_CMD_FLASH=y
+CONFIG_CMD_BOOTM_SHOW_TYPE=y
+CONFIG_CMD_RESET=y
+CONFIG_CMD_GO=y
+CONFIG_CMD_TIMEOUT=y
+CONFIG_CMD_PARTITION=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_LED=y
+CONFIG_CMD_LED_TRIGGER=y
+CONFIG_NET=y
+CONFIG_NET_DHCP=y
+CONFIG_NET_NFS=y
+CONFIG_NET_PING=y
+CONFIG_NET_TFTP=y
+CONFIG_NET_TFTP_PUSH=y
+CONFIG_NET_NETCONSOLE=y
+CONFIG_DRIVER_SERIAL_ARM_DCC=y
+CONFIG_DRIVER_SERIAL_NS16550=y
+CONFIG_DRIVER_NET_IXP4XX_ETH=y
+# CONFIG_SPI is not set
+CONFIG_DRIVER_CFI=y
+# CONFIG_DRIVER_CFI_AMD is not set
+# CONFIG_DRIVER_CFI_BANK_WIDTH_1 is not set
+# CONFIG_DRIVER_CFI_BANK_WIDTH_4 is not set
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_LED_TRIGGERS=y
+CONFIG_FS_CRAMFS=y
+CONFIG_SHA1=y
+CONFIG_SHA256=y
diff --git a/arch/arm/cpu/Kconfig b/arch/arm/cpu/Kconfig
index f55e862..230f596 100644
--- a/arch/arm/cpu/Kconfig
+++ b/arch/arm/cpu/Kconfig
@@ -46,10 +46,14 @@ config CPU_V7
select CPU_32v7
# Xscale PXA25x, PXA27x
-config CPU_XSCALE
+config CPU_PXA
bool
select CPU_32v4T
+config CPU_XSCALE
+ bool
+ select CPU_32v5
+
# Figure out what processor architecture version we should be using.
# This defines the compiler instruction set which depends on the machine type.
config CPU_32v4T
diff --git a/arch/arm/mach-ixp4xx/Kconfig b/arch/arm/mach-ixp4xx/Kconfig
index f9388bf..480511c 100644
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -1,13 +1,25 @@
if ARCH_IXP4XX
+config ARCH_TEXT_BASE
+ hex
+ default 0x00f80000
+
config IXP4XX_GENERIC_LOWLEVEL_INIT
bool
choice
prompt "IXP4xx Board Type"
+config MACH_NSLU2
+ bool "Linksys NSLU2"
+ select MACH_HAS_LOWLEVEL_INIT
+ select IXP4XX_GENERIC_LOWLEVEL_INIT
+
endchoice
+config BOARDINFO
+ default "Linksys NSLU2" if MACH_NSLU2
+
config IXP4XX_QMGR
tristate "IXP4xx Queue Manager support"
help
diff --git a/arch/arm/mach-ixp4xx/board_lowlevel_init.c b/arch/arm/mach-ixp4xx/board_lowlevel_init.c
index 061246d..e5a43da 100644
--- a/arch/arm/mach-ixp4xx/board_lowlevel_init.c
+++ b/arch/arm/mach-ixp4xx/board_lowlevel_init.c
@@ -11,10 +11,12 @@
#include <asm/system.h>
#include <mach/ixp4xx-regs.h>
+#define nop() asm volatile ("nop;\n\t"::)
+
static void inline delay(int x)
{
while (x-- > 0)
- barrier();
+ nop();
}
void __naked __bare_init board_init_lowlevel(void)
--
1.7.9.1
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* [PATCH 08/10] ARM: Add support for Goramo Multilink router platform.
2012-04-23 6:56 [PATCH 00/10] IXP4xx rebase WIP Jean-Christophe PLAGNIOL-VILLARD
` (6 preceding siblings ...)
2012-04-23 7:02 ` [PATCH 07/10] ARM: Add support for Linksys NSLU2 support Jean-Christophe PLAGNIOL-VILLARD
@ 2012-04-23 7:02 ` Jean-Christophe PLAGNIOL-VILLARD
2012-04-23 7:02 ` [PATCH 09/10] nslu2: NPE-B firmware + boot script Jean-Christophe PLAGNIOL-VILLARD
` (2 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-04-23 7:02 UTC (permalink / raw)
To: barebox; +Cc: Krzysztof Hałasa
From: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
Documentation/boards.dox | 1 +
arch/arm/Makefile | 1 +
arch/arm/boards/multilink/Makefile | 1 +
arch/arm/boards/multilink/env/config | 36 ++++++++
arch/arm/boards/multilink/lowlevel_init.S | 64 ++++++++++++++
arch/arm/boards/multilink/multilink.c | 131 +++++++++++++++++++++++++++++
arch/arm/boards/multilink/multilink.dox | 36 ++++++++
arch/arm/configs/multilink_defconfig | 55 ++++++++++++
arch/arm/mach-ixp4xx/Kconfig | 5 +
9 files changed, 330 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/boards/multilink/Makefile
create mode 100644 arch/arm/boards/multilink/config.h
create mode 100644 arch/arm/boards/multilink/env/config
create mode 100644 arch/arm/boards/multilink/lowlevel_init.S
create mode 100644 arch/arm/boards/multilink/multilink.c
create mode 100644 arch/arm/boards/multilink/multilink.dox
create mode 100644 arch/arm/configs/multilink_defconfig
diff --git a/Documentation/boards.dox b/Documentation/boards.dox
index ba332a7..27edc62 100644
--- a/Documentation/boards.dox
+++ b/Documentation/boards.dox
@@ -21,6 +21,7 @@ ARM type:
@li @subpage board_loco
@li @subpage chumbyone
@li @subpage scb9328
+ at li @subpage multilink
@li @subpage netx
@li @subpage dev_omap_arch
@li @subpage a9m2440
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 34abd19..782938a 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -94,6 +94,7 @@ board-$(CONFIG_MACH_IMX21ADS) := imx21ads
board-$(CONFIG_MACH_IMX27ADS) := imx27ads
board-$(CONFIG_MACH_MIOA701) := mioa701
board-$(CONFIG_MACH_MMCCPU) := mmccpu
+board-$(CONFIG_MACH_MULTILINK) := multilink
board-$(CONFIG_MACH_MX1ADS) := mx1ads
board-$(CONFIG_MACH_NOMADIK_8815NHK) := nhk8815
board-$(CONFIG_MACH_NXDB500) := netx
diff --git a/arch/arm/boards/multilink/Makefile b/arch/arm/boards/multilink/Makefile
new file mode 100644
index 0000000..d5a8bbc
--- /dev/null
+++ b/arch/arm/boards/multilink/Makefile
@@ -0,0 +1 @@
+obj-y += lowlevel_init.o multilink.o
diff --git a/arch/arm/boards/multilink/config.h b/arch/arm/boards/multilink/config.h
new file mode 100644
index 0000000..e69de29
diff --git a/arch/arm/boards/multilink/env/config b/arch/arm/boards/multilink/env/config
new file mode 100644
index 0000000..3a6eaa2
--- /dev/null
+++ b/arch/arm/boards/multilink/env/config
@@ -0,0 +1,36 @@
+#!/bin/sh
+
+# use 'dhcp' to do dhcp in barebox and in kernel
+# use 'none' if you want to skip kernel ip autoconfiguration
+ip=dhcp-barebox
+dhcp_vendor_id=barebox-nslu2
+
+# or set your networking parameters here
+#eth0.ipaddr=a.b.c.d
+#eth0.netmask=a.b.c.d
+#eth0.gateway=a.b.c.d
+#eth0.serverip=a.b.c.d
+
+# can be either 'nfs', 'tftp' or 'nor'
+kernel_loc=nfs
+# can be either 'net', 'nor' or 'initrd'
+rootfs_loc=net
+
+# can be either 'jffs2' or 'ubifs'
+rootfs_type=ubifs
+rootfsimage=root.$rootfs_type
+
+kernelimage=zImage
+#kernelimage=uImage
+#kernelimage=Image
+#kernelimage=Image.lzo
+
+nor_parts="256k(barebox)ro,64k(bareboxenv),1536k(kernel),-(root)"
+rootfs_mtdblock_nor=3
+
+autoboot_timeout=3
+
+bootargs="console=ttyS0,115200"
+
+# set a fancy prompt (if support is compiled in)
+PS1="\e[1;32mbarebox@\e[1;31m\h:\w\e[0m\n# "
diff --git a/arch/arm/boards/multilink/lowlevel_init.S b/arch/arm/boards/multilink/lowlevel_init.S
new file mode 100644
index 0000000..970ef72
--- /dev/null
+++ b/arch/arm/boards/multilink/lowlevel_init.S
@@ -0,0 +1,64 @@
+#include <mach/ixp4xx-regs.h>
+
+ .section ".text_bare_init", "ax"
+ .balign 0x40
+ .space 0x40 /* configuration block at 0x40 */
+
+ .macro DELAY_FOR cycles, reg0
+ ldr \reg0, =\cycles
+ subs \reg0, \reg0, #1
+ subne pc, pc, #0xc
+ .endm
+
+#define CFG_SDRAM_SIZE 0x50 /* u32 */
+#define CFG_SDRAM_CONF 0x54 /* u32 */
+#define CFG_SDRAM_MODE 0x58 /* u32 */
+#define CFG_SDRAM_REFRESH 0x5C /* u32 */
+
+.globl board_init_lowlevel
+board_init_lowlevel:
+ mov r8, #IXP4XX_EXP_BASE(0)
+ ldr r1, [r8, #CFG_SDRAM_CONF]
+ ldr r2, =IXP4XX_SDRAM_CONFIG
+ str r1, [r2]
+
+ /* disable refresh cycles */
+ mov r1, #0
+ add r2, r2, #4 /* r2 = IXP4XX_SDRAM_REFRESH */
+ str r1, [r2]
+
+ /* send NOP command */
+ mov r1, #3
+ add r3, r2, #4 /* r3 = IXP4XX_SDRAM_IR */
+ str r1, [r3]
+ DELAY_FOR 0x4000, r0
+
+ /* set SDRAM internal refresh */
+ ldr r1, [r8, #CFG_SDRAM_REFRESH]
+ str r1, [r2]
+ DELAY_FOR 0x4000, r0
+
+ /* send precharge-all command to close all open banks */
+ mov r1, #2
+ str r1, [r3]
+ DELAY_FOR 0x4000, r0
+
+ /* provide 8 auto-refresh cycles */
+ mov r1, #4
+ mov r4, #8
+1: str r1, [r3]
+ DELAY_FOR 0x100, r0
+ subs r4, r4, #1
+ bne 1b
+
+ /* set mode register in SDRAM */
+ ldr r1, [r8, #CFG_SDRAM_MODE]
+ str r1, [r3]
+ DELAY_FOR 0x4000, r0
+
+ /* send normal operation command */
+ mov r1, #6
+ str r1, [r3]
+ DELAY_FOR 0x4000, r0
+
+ mov pc, lr
diff --git a/arch/arm/boards/multilink/multilink.c b/arch/arm/boards/multilink/multilink.c
new file mode 100644
index 0000000..5d497b5
--- /dev/null
+++ b/arch/arm/boards/multilink/multilink.c
@@ -0,0 +1,131 @@
+//#define DEBUG
+#include <common.h>
+#include <errno.h>
+#include <init.h>
+#include <linux/types.h>
+#include <asm/armlinux.h>
+#include <asm/io.h>
+#include <io.h>
+#include <generated/mach-types.h>
+#include <mach/ixp4xx-regs.h>
+#include <mach/platform.h>
+
+/* offsets from start of flash ROM = 0x50000000 */
+#define CFG_ETH0_ADDRESS 0x40 /* 6 bytes */
+#define CFG_ETH1_ADDRESS 0x46 /* 6 bytes */
+#define CFG_REV 0x4C /* u32 */
+#define CFG_SDRAM_SIZE 0x50 /* u32 */
+#define CFG_SDRAM_CONF 0x54 /* u32 */
+#define CFG_SDRAM_MODE 0x58 /* u32 */
+#define CFG_SDRAM_REFRESH 0x5C /* u32 */
+
+#define CFG_HW_BITS 0x60 /* u32 */
+#define CFG_HW_USB_PORTS 0x00000007 /* 0 = no NEC chip, 1-5 = ports # */
+#define CFG_HW_HAS_PCI_SLOT 0x00000008
+#define CFG_HW_HAS_ETH0 0x00000010
+#define CFG_HW_HAS_ETH1 0x00000020
+#define CFG_HW_HAS_HSS0 0x00000040
+#define CFG_HW_HAS_HSS1 0x00000080
+#define CFG_HW_HAS_UART0 0x00000100
+#define CFG_HW_HAS_UART1 0x00000200
+#define CFG_HW_HAS_EEPROM 0x00000400
+
+#define ETH_ALEN 6
+
+#define BAREBOX_START 0x00000
+#define BAREBOX_LENGTH 0x34000
+#define NPE_A_START (BAREBOX_START + BAREBOX_LENGTH)
+#define NPE_A_LENGTH 0x05000
+#define NPE_B_START (NPE_A_START + NPE_A_LENGTH)
+#define NPE_B_LENGTH 0x03000
+#define NPE_C_START (NPE_B_START + NPE_B_LENGTH)
+#define NPE_C_LENGTH 0x04000
+#define NPE_ENV0_START (NPE_C_START + NPE_C_LENGTH)
+#define NPE_ENV0_LENGTH 0x20000
+
+#ifdef CONFIG_DRIVER_NET_IXP4XX_ETH
+static struct eth_plat_info eth_pinfo[2] = {
+ {
+ .npe = 1,
+ .phy = 0,
+ .rxq = 20,
+ .txreadyq = 29,
+ }, {
+ .npe = 2,
+ .phy = 1,
+ .rxq = 21,
+ .txreadyq = 30,
+ }
+};
+
+static void gml_eth_init(void)
+{
+ int i;
+ u32 hw_bits;
+
+ hw_bits = __raw_readl(IXP4XX_EXP_BASE(0) + CFG_HW_BITS);
+
+ if (hw_bits & CFG_HW_HAS_ETH0) {
+ for (i = 0; i < ETH_ALEN; i++)
+ eth_pinfo[0].hwaddr[i] = cpu_readb(CFG_ETH0_ADDRESS + i);
+ ixp4xx_add_eth(1, ð_pinfo[0]);
+ }
+
+ if (hw_bits & CFG_HW_HAS_ETH1) {
+ for (i = 0; i < ETH_ALEN; i++)
+ eth_pinfo[1].hwaddr[i] = cpu_readb(CFG_ETH1_ADDRESS + i);
+ ixp4xx_add_eth(2, ð_pinfo[1]);
+ }
+}
+#else
+static void gml_eth_init(void) {}
+#endif
+
+static int gml_mem_init(void)
+{
+ u32 size = __raw_readl(IXP4XX_EXP_BASE(0) + CFG_SDRAM_SIZE);
+
+ arm_add_mem_device("ram0", 0x00000000, size);
+
+ return 0;
+}
+mem_initcall(gml_mem_init);
+
+static inline u8 __init flash_readb(u32 addr)
+{
+ return __raw_readb(IXP4XX_EXP_BASE(0) + addr);
+}
+
+static int __init gml_devices_init(void)
+{
+ IXP4XX_EXP_CS0 = IXP4XX_EXP_EN | IXP4XX_EXP_INTEL |
+ IXP4XX_EXP_BITS(24) | IXP4XX_EXP_WR_EN | IXP4XX_EXP_BYTE_RD16;
+
+ add_cfi_flash_device(0, IXP4XX_EXP_BASE(0), 0, 0);
+
+ devfs_add_partition("nor0", BAREBOX_START, BAREBOX_LENGTH,
+ DEVFS_PARTITION_FIXED | DEVFS_PARTITION_READONLY, "barebox");
+ devfs_add_partition("nor0", NPE_A_START, NPE_A_LENGTH,
+ DEVFS_PARTITION_FIXED | DEVFS_PARTITION_READONLY, "NPE-A");
+ devfs_add_partition("nor0", NPE_B_START, NPE_B_LENGTH,
+ DEVFS_PARTITION_FIXED | DEVFS_PARTITION_READONLY, "NPE-B");
+ devfs_add_partition("nor0", NPE_C_START, NPE_C_LENGTH,
+ DEVFS_PARTITION_FIXED | DEVFS_PARTITION_READONLY, "NPE-C");
+ devfs_add_partition("nor0", NPE_ENV0_START, NPE_ENV0_LENGTH,
+ DEVFS_PARTITION_FIXED, "env0");
+
+ gml_eth_init();
+
+ armlinux_set_bootparams((void *)(0x00000100));
+ armlinux_set_architecture(MACH_TYPE_GORAMO_MLR);
+
+ return 0;
+}
+device_initcall(gml_devices_init);
+
+static int gml_console_init(void)
+{
+ ixp4xx_add_uart1();
+ return 0;
+}
+console_initcall(gml_console_init);
diff --git a/arch/arm/boards/multilink/multilink.dox b/arch/arm/boards/multilink/multilink.dox
new file mode 100644
index 0000000..eada1e1
--- /dev/null
+++ b/arch/arm/boards/multilink/multilink.dox
@@ -0,0 +1,36 @@
+/** @page multilink Goramo MultiLink
+
+These boards are based on Intel IXP42x CPU.
+
+Variants:
+
+MicroRouter module: IXP421 or IXP425 266 MHz CPU, 32 MiB SDRAM,
+ 1 or 2 Fast Ethernet ports, 2 sync serial ports, 1 RS-232 (console) port.
+
+MultiLink v.1: IXP425 266 or 533 MHz CPU, 64 - 256 MiB SDRAM,
+ 2 Fast Ethernet ports, 2 sync serial ports, 1 - 2 RS-232 ports,
+ a mini-PCI slot, 2 optional USB host connectors.
+
+MultiLink v.2: IXP425 266 or 533 MHz CPU, 64 - 256 MiB SDRAM,
+ 2 Fast Ethernet ports, 2 sync serial ports, 1 - 2 RS-232 ports,
+ 2 additional optional Fast or Gigabit Ethernet ports, a mini-PCI slot,
+ 4 optional USB host connectors, optional Real-Time Clock,
+ optional IDE connector.
+
+16 MiB Intel StrataFlash memory is partitioned as follows:
+
+0x00000-0x34000 : Barebox image
+0x34000-0x39000 : NPE-A microcode
+0x39000-0x3c000 : NPE-B microcode
+0x3c000-0x40000 : NPE-C microcode
+0x40000-0x60000 : env0
+
+There is a factory configuration region within Barebox image at locations
+0x40 - 0x7F. Details are in file multilink.c
+
+Barebox image and NPE microcode files are combined in first two blocks
+of flash memory. NPE-A microcode is not used by Barebox (but may be used
+by Linux HSS driver). NPE-B microcode is needed for eth0 and NPE-C for
+eth1. Barebox needs version 2.4 of regular non-VLAN-aware microcode files
+(with or without crypto support).
+*/
diff --git a/arch/arm/configs/multilink_defconfig b/arch/arm/configs/multilink_defconfig
new file mode 100644
index 0000000..f090ec8
--- /dev/null
+++ b/arch/arm/configs/multilink_defconfig
@@ -0,0 +1,55 @@
+CONFIG_ARCH_IXP4XX=y
+CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y
+# CONFIG_ARM_EXCEPTIONS is not set
+CONFIG_TEXT_BASE=0x01d00000
+CONFIG_EXPERIMENTAL=y
+# CONFIG_MACH_DO_LOWLEVEL_INIT is not set
+CONFIG_LONGHELP=y
+CONFIG_GLOB=y
+CONFIG_PROMPT_HUSH_PS2="mgl# "
+CONFIG_HUSH_FANCY_PROMPT=y
+CONFIG_CMDLINE_EDITING=y
+CONFIG_AUTO_COMPLETE=y
+CONFIG_MENU=y
+# CONFIG_CONSOLE_ACTIVATE_FIRST is not set
+CONFIG_CONSOLE_ACTIVATE_ALL=y
+CONFIG_PARTITION=y
+CONFIG_DEFAULT_ENVIRONMENT_GENERIC=y
+CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/multilink/env"
+CONFIG_DEBUG_INFO=y
+CONFIG_CMD_EDIT=y
+CONFIG_CMD_SLEEP=y
+CONFIG_CMD_SAVEENV=y
+CONFIG_CMD_LOADENV=y
+CONFIG_CMD_EXPORT=y
+CONFIG_CMD_PRINTENV=y
+CONFIG_CMD_READLINE=y
+CONFIG_CMD_MENU=y
+CONFIG_CMD_MENU_MANAGEMENT=y
+CONFIG_CMD_PASSWD=y
+CONFIG_CMD_ECHO_E=y
+CONFIG_CMD_LOADB=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_MTEST=y
+CONFIG_CMD_FLASH=y
+CONFIG_CMD_BOOTM_ZLIB=y
+CONFIG_CMD_BOOTM_BZLIB=y
+CONFIG_CMD_BOOTM_SHOW_TYPE=y
+CONFIG_CMD_RESET=y
+CONFIG_CMD_GO=y
+CONFIG_CMD_TIMEOUT=y
+CONFIG_CMD_PARTITION=y
+CONFIG_CMD_UNLZO=y
+CONFIG_NET=y
+CONFIG_NET_DHCP=y
+CONFIG_NET_NFS=y
+CONFIG_NET_PING=y
+CONFIG_NET_TFTP=y
+CONFIG_NET_TFTP_PUSH=y
+CONFIG_NET_NETCONSOLE=y
+CONFIG_DRIVER_SERIAL_ARM_DCC=y
+CONFIG_DRIVER_SERIAL_NS16550=y
+# CONFIG_SPI is not set
+CONFIG_FS_CRAMFS=y
+CONFIG_SHA1=y
+CONFIG_SHA256=y
diff --git a/arch/arm/mach-ixp4xx/Kconfig b/arch/arm/mach-ixp4xx/Kconfig
index 480511c..3960811 100644
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -10,6 +10,10 @@ config IXP4XX_GENERIC_LOWLEVEL_INIT
choice
prompt "IXP4xx Board Type"
+config MACH_MULTILINK
+ bool "Goramo MultiLink"
+ select MACH_HAS_LOWLEVEL_INIT
+
config MACH_NSLU2
bool "Linksys NSLU2"
select MACH_HAS_LOWLEVEL_INIT
@@ -18,6 +22,7 @@ config MACH_NSLU2
endchoice
config BOARDINFO
+ default "Goramo MultiLink" if MACH_MULTILINK
default "Linksys NSLU2" if MACH_NSLU2
config IXP4XX_QMGR
--
1.7.9.1
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* [PATCH 09/10] nslu2: NPE-B firmware + boot script
2012-04-23 6:56 [PATCH 00/10] IXP4xx rebase WIP Jean-Christophe PLAGNIOL-VILLARD
` (7 preceding siblings ...)
2012-04-23 7:02 ` [PATCH 08/10] ARM: Add support for Goramo Multilink router platform Jean-Christophe PLAGNIOL-VILLARD
@ 2012-04-23 7:02 ` Jean-Christophe PLAGNIOL-VILLARD
2012-04-23 7:02 ` [PATCH 10/10] multilink: " Jean-Christophe PLAGNIOL-VILLARD
2012-04-24 8:08 ` [PATCH 00/10] IXP4xx rebase WIP Sascha Hauer
10 siblings, 0 replies; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-04-23 7:02 UTC (permalink / raw)
To: barebox
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
arch/arm/boards/nslu2/env/NPE-B | Bin 0 -> 11964 bytes
arch/arm/boards/nslu2/env/bin/init_board | 4 ++++
2 files changed, 4 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/boards/nslu2/env/NPE-B
create mode 100644 arch/arm/boards/nslu2/env/bin/init_board
diff --git a/arch/arm/boards/nslu2/env/NPE-B b/arch/arm/boards/nslu2/env/NPE-B
new file mode 100644
index 0000000000000000000000000000000000000000..e62a944d267d429961eb1433b30e0ecdedc251f6
GIT binary patch
literal 11964
zcmeHNe{dA{b$`2id%8sudXmnPj1O32Ac}*`0m9JMR#x=xkWv{=V1p(#_+T)C6sN-R
zNJ%CYYY<4rI6VufDW-{xG0{-h)l5NF-9$ZsY)e#(PXuDD(pq%@+ls()99PK5sGsld
z9(KmIJn?j<fAm)K?(O&2`@Z+S@7J#O`sJZ?iDZc=^?9<dR3Nm~)izFD>)?Y9ehxST
zfJ-fBs%56pA*M%~cuBjYHjkP_BXM$7SD}wsZkM=@Qdw@uV7cQu%P)V-@(zXNtuo7F
zA5n!#+#tp~hPke|p5<22|2qalln=-ndtckMQ_qOTIHTEM&?62|s&pnsbWgp93hG@n
zA8<3^RzNvmRlSP?wN=u&7_sztCQG{kPiLyGonbYfO?6>bR1J8WR3oQF-INzoH%y8{
zjx3fx{*X&3HH~8AqE6D%wz8IAVh9;DSB=3+k)-WHU$fI!R}&U}9C&0%y3lXSD*d9D
zrGEx20DQ9-IuLZPG0l%!x(L*oDRra7p>|0c!WwBC<~<JB-@(D%r^z#VtIf;EM_e*M
zGW8RAHk&N{<~1&(R9nBbL|jd*Y<Y&IlaoPLA^!kq4QL$PnL<<@VLF+@%AIbZE3{2k
zNMfon==OH)(|ub01|wT*#~IcbS_<SV+^M54rlsu+i#GVuSURX`^Dp@TIokXy#MGC<
za+@1t9uA(=h-%_Ar*8s3Rg{CZrj~v<Pn&TP<53UO1=6NJ%bM%SOqSwk_Zq+xSlT%m
zy4z#(QWM8oN%hw0psBLdcq_(rCRYn@ZQpM93wlofqxVAA72vA`GL_&yu3#*JwQE>9
zor?RlEcK<a^!$1bo=#_d5d5}Qa^O2eG2GK%OkpV>>%XHgZ45z{KV#ZA#DN1*MSmIe
zns0;5I!jqH)83U#PeaG84=|N8ONZP{ozQ2jpQR(<6Z1Zq6UNw5z@*O^D;;NS(Kus&
zGR|1xIAaCljLjTpZ0a~;dDeOPHV(100eZ^Pgr71khrX8KY?qtB@Za_vrZC3CD${po
zLcchlP4Ex+wWU+BW?7v*ckDf!(*}(FEmLMC%Ome#O%BV$mw>0U^xdyvE@*+SWg9N+
z`9?9*f!A5SR?NY36B72V<!^*7zd*caGix*I*9o81?!H3mQrNK>%%Qo%4>E1=Gv(g~
zyZ~o<4^wal_*=}ue1-A?A26u_*e&=CC>$vNwUX9p;M@n8+>bH^G@9P1v$SuTZQD69
z(i@|;4j_~CZ5K;j8i!seAc_kgNk`iQzVvKO_(VJ4FnD{x155xH?$ZFG&kKLMiK(H{
zUbDgcy*0uYgZtrY8=JKJuNzug-x|#~sDBAP_=kuKgC3k0WICt`e`i|n1#R8-OA*&<
z-&gW_V;DE#7qI!a;Hz($I7j%RXp8gO2tAFwXw%yX-$ATN(3P*h4Lt@h|33bkgBMiZ
z1)m5IQ!&oC0Y2&WxaYqba2Gb}?!x`h-!IFdzo{(!JMu^QM@)Pex;nwZCRvWfg>QkE
zBad4A(9`h0y?5iRrZL5rav(klb6^Xf8K3ke<5^!aKH*Eop@+3ToA3Rrn5Jz<8+O|E
z6nH^A*>gW^O0?6NDu7#Ir*FY0_AYSZ2jb2h|HM>KgE>DHF`FrOCGHQ1xK93aDS5{E
zbfPoqu>F64%?n!FS!%)=CUkNTIyqv3W-e&1!X9^7JX0L;<}+jS#~Hh0oH6(t^!)iW
zajsuDcJnx6w(dWlCT!~qX}Xx!!FJcJhrZxj!1Q1)<PI`b#f42lAIs6l99$QX=$#Y}
zwJAgaVT<W}?%mg+L(mV@p{>C-4cj)0cUg8xo7tj4A>`=Rxh(%!_<g0ie9M0$2Pp0|
z*ef?c=H8Du(6E<AyFYN>(KeB(`6-rP%I84PE9aek1$)4D?wyBxb%^(3efhFAu>BpZ
z{NQfHzzFg*V)$9F)hD;9cFqeH@*d>#@<1iV5MR!Ocz^3W_q6u8Or=$pyi|&_7XDHC
z6Ub1AKE#JoQIBK;hk-MJBfuHJIxuXn)DH|>voPXZDRR5D7I_QzRz2{ky+zx%c*tEC
z%5oQ0^}7q<>!N0pe=M`|SJ#9NSpK;Tz93@+u~WazJu9*R`m$;ZM}Cd>1ozyKWuG@-
z>siQm2J+Wl`^>&{7WO^-p?ex~0%|V71LC;<i}<kCyQ<?>y(RP}VvJaaHAF$bwReN?
zBf&rT)q$1T|4_YAoFDE>n@q(Uk5S#lDz)snY!0=ePP(|9OD^V49lbbP@m?rqN$-d3
zD*4tZtknFLX${UL@+ea_d@zi7CwvdIXaMnX0C8%|yG+$h^rA~b&C!AUgt&F#1V^7^
z)d(9b&3cZ_rWPt{lZmm;eBjp{?2}L%$5_!(H&#bc&oL{ql>G#9LGvn|qcvfz9(CBU
zOQan|Eq3$>pix&j3M^u09b&)$a&(WVX>hh(0#9V=z%AOYzYilX*1$G@2wcUq3i0<m
zcy6cx)H3Z_#!`=u=~N7IPG%GOYHeR@uiJ%K{5;k?gf)X$W6kk`FVdRtk7<coSK8;Z
zd27(MW7k2eD}`Ezhe7{!z<;8ST85nLyCEZ0M{W7qeH=V8m2|=HOYotBDh~XmPV~?R
zOq+xZh?le1;vTAcex=rY$7=8~SvyeYxAtCKgqq^A@wsD45$u2F_n9hjUhCl#bNt$|
zS38+zz)oMv;*uG2DbguZq+iq~X*jptj_kK-zqszx+71zFkjYF<ey0ArIIw-QY<7aD
zkADMNkn`0}I-0Q=v?g$L=_01GOw0bMY%zRaMJ)2G;WAQ<2m@!a`Pjo88i6hBgMJ`C
z?fWHS!3$QLr|K|GKlMKO?it~zKca?(o!*Y;70Z_KJaId04QsYpHi6i8M1uYe?a+YN
znv*}umOkXM*D!XoCC5?A9&bhs^`3avqPr;7{f&hZA@oplwa&XmZM{e5y0AgV%qH80
zMGTBJS#xfxdxoRYTz6h{3Z4U4Ekj(KQ9oV1ANEEai(sdnwmyE27*a8l<x_97vQY2|
z+FO3dfv_R#oy6qOkjI8?d1_)Dg|Aw4gx_E-)>*s=Kay_nvIBZlROCU(@S!zd$l(`z
zjrFKy9mWm+7taX{S!gk<<)NQ(5Hb+<*}cWt(|*=LeG}I5D~wN`YlJLOKl#P8OY0Q+
zqdpV9g!s4`b;D}-<?8M7)iaPG=Y6I_Y};enFwQ&$Ik?HvnRMs`o;3g$w!w~&o6=AR
z$F?z<QI;lMgzezj^qB?Z`|~SIQ%*BIfY|NFoZf#$O`YqUv4ObyEAm#izz(muJx6rW
zFJJvH@cLvG;?5}3pr{{Ed+qObi+DzTh&O%RsQ-?WuNV9E)(d?({m0S&3h9GxtV#5}
z0va=s3nx<AW#plnx2@Pjm#Z;HJhye&Hek{103UBUv=EoJoX7YHw|_8%xscJCa{~Rp
z!akiAy-)f((H}?u%hvwN4^BDrUq=5)Ti$NSB%UL^VU}_#kSAv`t(e8qy=bqfK)-?h
zl27#;99&VNP;U!MPr`S)Z^gN-gwBR&-j+d}wJzvoY(MOBu*cq~hOPEvm#lu&LsCYA
z&~0RrJlKnKO~i1}lm=v89K-oHLOx-Kr)3U}4d7hy%=iv!_5supW0!#8+hxSkMA&*4
zX!Lvwa65;F-(<Py87`^yBhDELodvJmE%Xh@85%ohulqYcmvs>tr%aq#OmUsXem%Fq
z7BF`;=&i;c!>2Hgm~#%aC-oyf!)DGg&Kl1iRy;6;e+#)_&t5IR(n!3Az!@pp-Iq{P
z;8{o1L9{vx{w3@L?*j5($JwFw#2)g<6)x?$h4fR$Z5~dwSTRuWQWC8qz1QgnU)1w3
z)3;GeVt;$>n~>)a>^u%Q4qZTgyz`)m5vF^-#<Uc5WaD1gc$HPtQ`*Cbb0b*ul;Z7*
zad1E-*C_+KT4CjCS5Hj7+AZ41LppT71au=S5i1|J=F@5D!J!pc(qhd`v_oTC73z+1
zurjPrm(Ib<Va3<2v-B>WB_0f8Pvku4O2iG3YeQqzim%JSdlNDCJ=%1pii1;#B6!ZB
z3TB$R0Q!H3rS-%m>vM_2MO1b6CvLrBi979)e)n9|K!H0=@?SOZ4rd5D!<pR~Wom0-
zDgup1Owe7Wq+t(QM|jWi$4rmSLCz}1dj-^`8-f_W4?N(!D+LeBaNoqG;NRCxRQN^<
z2j2*j-a|r9at!trDuO%*vCnz%G*uUK#9ZW$-?H?EpivARG=XOW_eHQ*@aWjdHq;F1
zhrN`45&Rsg(eh^^-#;-I`EZV%7m*WZ)CUswBW#EKJ-K+Ffm-k5_w4r><I~ezf}VJ$
zhTXv?wS|Yl8)%4p3mc?47Of$RR%q<&;BgjUHsCJ6j{x<6zXoIgCIZp{X@GwOOaL4M
zya*8f=LV>NMt}l%0?+}dhwl5u`!l=)^IK<Q-6IDi-m#g;pQx#XZWO)OL=9tV%@xR@
zeRl2y?{pM4V(HF~CzjnTwEM6oma)CQPRIysTJt>B{i1E{{VnVr9%1s}*;&|zXjfg0
zkOy_0-~s%|qp&k+zbW2rQa)nn_CAvw`j`h=TVAtcusA<)xn&zCf0G(WY9OhBqy~~2
zNNOOdfushK8c1p&sez;hk{b9w)_}|2Kkuiv)Fn6(_hYyc?HhQi^h3&YTHlnuNAsNf
z*-{lv!{;?$;VM|9RQjZXfK-Q%S&HT36R6-%=^-~27|OFQDkvc`sbH}>d5KgIbWO>!
zb}(uFRwe!;n!iJCp5hi=rqeIJVZ!JRSIRoY`ko2jJmEjGF`~S*1miZ&n`JGbJiL7r
zSKd_zC%%}noBvC{?6C>q6_s^yo`ZD<=R4T%;Dru091J~(i^C4CaB#%I8ysBa;O{%w
zbZ~=%qYmEZ;3fw*JGjNcZ4Qn(xXZzD2cL6rzk}a#@Q{PA+Bo@})Id@LNev`5@c&l>
zBHv~j022@+5;;5z?JTsj(9T9X8|`egv(fgVEiSKNA@Z6Ij@kGo8_`XM(>5I(6WBG|
zHP5xc6?E;u-_tIi^A`i|a{ZgrIs*JN*Ll~o_R2rxH$sy6hs?+K)K~2JZhXT;MTxbb
zGemj#*A+=EiN4R^(L|3Yar1>Z;*5M%?D4oL4e-@279W@6694Xy^Q3=KuRydLm;Eie
ddl5P$=RSaYl`^Nzn>H_SUl%<&nrjoF{{f0owX6UD
literal 0
HcmV?d00001
diff --git a/arch/arm/boards/nslu2/env/bin/init_board b/arch/arm/boards/nslu2/env/bin/init_board
new file mode 100644
index 0000000..96ece8d
--- /dev/null
+++ b/arch/arm/boards/nslu2/env/bin/init_board
@@ -0,0 +1,4 @@
+#!/bin/sh
+
+mkdir /firmware
+cp /env/NPE-B /firmware
--
1.7.9.1
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* [PATCH 10/10] multilink: NPE-B firmware + boot script
2012-04-23 6:56 [PATCH 00/10] IXP4xx rebase WIP Jean-Christophe PLAGNIOL-VILLARD
` (8 preceding siblings ...)
2012-04-23 7:02 ` [PATCH 09/10] nslu2: NPE-B firmware + boot script Jean-Christophe PLAGNIOL-VILLARD
@ 2012-04-23 7:02 ` Jean-Christophe PLAGNIOL-VILLARD
2012-04-24 8:08 ` [PATCH 00/10] IXP4xx rebase WIP Sascha Hauer
10 siblings, 0 replies; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-04-23 7:02 UTC (permalink / raw)
To: barebox
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
arch/arm/boards/multilink/env/NPE-B | Bin 0 -> 11964 bytes
arch/arm/boards/multilink/env/bin/init_board | 4 ++++
2 files changed, 4 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/boards/multilink/env/NPE-B
create mode 100644 arch/arm/boards/multilink/env/bin/init_board
diff --git a/arch/arm/boards/multilink/env/NPE-B b/arch/arm/boards/multilink/env/NPE-B
new file mode 100644
index 0000000000000000000000000000000000000000..e62a944d267d429961eb1433b30e0ecdedc251f6
GIT binary patch
literal 11964
zcmeHNe{dA{b$`2id%8sudXmnPj1O32Ac}*`0m9JMR#x=xkWv{=V1p(#_+T)C6sN-R
zNJ%CYYY<4rI6VufDW-{xG0{-h)l5NF-9$ZsY)e#(PXuDD(pq%@+ls()99PK5sGsld
z9(KmIJn?j<fAm)K?(O&2`@Z+S@7J#O`sJZ?iDZc=^?9<dR3Nm~)izFD>)?Y9ehxST
zfJ-fBs%56pA*M%~cuBjYHjkP_BXM$7SD}wsZkM=@Qdw@uV7cQu%P)V-@(zXNtuo7F
zA5n!#+#tp~hPke|p5<22|2qalln=-ndtckMQ_qOTIHTEM&?62|s&pnsbWgp93hG@n
zA8<3^RzNvmRlSP?wN=u&7_sztCQG{kPiLyGonbYfO?6>bR1J8WR3oQF-INzoH%y8{
zjx3fx{*X&3HH~8AqE6D%wz8IAVh9;DSB=3+k)-WHU$fI!R}&U}9C&0%y3lXSD*d9D
zrGEx20DQ9-IuLZPG0l%!x(L*oDRra7p>|0c!WwBC<~<JB-@(D%r^z#VtIf;EM_e*M
zGW8RAHk&N{<~1&(R9nBbL|jd*Y<Y&IlaoPLA^!kq4QL$PnL<<@VLF+@%AIbZE3{2k
zNMfon==OH)(|ub01|wT*#~IcbS_<SV+^M54rlsu+i#GVuSURX`^Dp@TIokXy#MGC<
za+@1t9uA(=h-%_Ar*8s3Rg{CZrj~v<Pn&TP<53UO1=6NJ%bM%SOqSwk_Zq+xSlT%m
zy4z#(QWM8oN%hw0psBLdcq_(rCRYn@ZQpM93wlofqxVAA72vA`GL_&yu3#*JwQE>9
zor?RlEcK<a^!$1bo=#_d5d5}Qa^O2eG2GK%OkpV>>%XHgZ45z{KV#ZA#DN1*MSmIe
zns0;5I!jqH)83U#PeaG84=|N8ONZP{ozQ2jpQR(<6Z1Zq6UNw5z@*O^D;;NS(Kus&
zGR|1xIAaCljLjTpZ0a~;dDeOPHV(100eZ^Pgr71khrX8KY?qtB@Za_vrZC3CD${po
zLcchlP4Ex+wWU+BW?7v*ckDf!(*}(FEmLMC%Ome#O%BV$mw>0U^xdyvE@*+SWg9N+
z`9?9*f!A5SR?NY36B72V<!^*7zd*caGix*I*9o81?!H3mQrNK>%%Qo%4>E1=Gv(g~
zyZ~o<4^wal_*=}ue1-A?A26u_*e&=CC>$vNwUX9p;M@n8+>bH^G@9P1v$SuTZQD69
z(i@|;4j_~CZ5K;j8i!seAc_kgNk`iQzVvKO_(VJ4FnD{x155xH?$ZFG&kKLMiK(H{
zUbDgcy*0uYgZtrY8=JKJuNzug-x|#~sDBAP_=kuKgC3k0WICt`e`i|n1#R8-OA*&<
z-&gW_V;DE#7qI!a;Hz($I7j%RXp8gO2tAFwXw%yX-$ATN(3P*h4Lt@h|33bkgBMiZ
z1)m5IQ!&oC0Y2&WxaYqba2Gb}?!x`h-!IFdzo{(!JMu^QM@)Pex;nwZCRvWfg>QkE
zBad4A(9`h0y?5iRrZL5rav(klb6^Xf8K3ke<5^!aKH*Eop@+3ToA3Rrn5Jz<8+O|E
z6nH^A*>gW^O0?6NDu7#Ir*FY0_AYSZ2jb2h|HM>KgE>DHF`FrOCGHQ1xK93aDS5{E
zbfPoqu>F64%?n!FS!%)=CUkNTIyqv3W-e&1!X9^7JX0L;<}+jS#~Hh0oH6(t^!)iW
zajsuDcJnx6w(dWlCT!~qX}Xx!!FJcJhrZxj!1Q1)<PI`b#f42lAIs6l99$QX=$#Y}
zwJAgaVT<W}?%mg+L(mV@p{>C-4cj)0cUg8xo7tj4A>`=Rxh(%!_<g0ie9M0$2Pp0|
z*ef?c=H8Du(6E<AyFYN>(KeB(`6-rP%I84PE9aek1$)4D?wyBxb%^(3efhFAu>BpZ
z{NQfHzzFg*V)$9F)hD;9cFqeH@*d>#@<1iV5MR!Ocz^3W_q6u8Or=$pyi|&_7XDHC
z6Ub1AKE#JoQIBK;hk-MJBfuHJIxuXn)DH|>voPXZDRR5D7I_QzRz2{ky+zx%c*tEC
z%5oQ0^}7q<>!N0pe=M`|SJ#9NSpK;Tz93@+u~WazJu9*R`m$;ZM}Cd>1ozyKWuG@-
z>siQm2J+Wl`^>&{7WO^-p?ex~0%|V71LC;<i}<kCyQ<?>y(RP}VvJaaHAF$bwReN?
zBf&rT)q$1T|4_YAoFDE>n@q(Uk5S#lDz)snY!0=ePP(|9OD^V49lbbP@m?rqN$-d3
zD*4tZtknFLX${UL@+ea_d@zi7CwvdIXaMnX0C8%|yG+$h^rA~b&C!AUgt&F#1V^7^
z)d(9b&3cZ_rWPt{lZmm;eBjp{?2}L%$5_!(H&#bc&oL{ql>G#9LGvn|qcvfz9(CBU
zOQan|Eq3$>pix&j3M^u09b&)$a&(WVX>hh(0#9V=z%AOYzYilX*1$G@2wcUq3i0<m
zcy6cx)H3Z_#!`=u=~N7IPG%GOYHeR@uiJ%K{5;k?gf)X$W6kk`FVdRtk7<coSK8;Z
zd27(MW7k2eD}`Ezhe7{!z<;8ST85nLyCEZ0M{W7qeH=V8m2|=HOYotBDh~XmPV~?R
zOq+xZh?le1;vTAcex=rY$7=8~SvyeYxAtCKgqq^A@wsD45$u2F_n9hjUhCl#bNt$|
zS38+zz)oMv;*uG2DbguZq+iq~X*jptj_kK-zqszx+71zFkjYF<ey0ArIIw-QY<7aD
zkADMNkn`0}I-0Q=v?g$L=_01GOw0bMY%zRaMJ)2G;WAQ<2m@!a`Pjo88i6hBgMJ`C
z?fWHS!3$QLr|K|GKlMKO?it~zKca?(o!*Y;70Z_KJaId04QsYpHi6i8M1uYe?a+YN
znv*}umOkXM*D!XoCC5?A9&bhs^`3avqPr;7{f&hZA@oplwa&XmZM{e5y0AgV%qH80
zMGTBJS#xfxdxoRYTz6h{3Z4U4Ekj(KQ9oV1ANEEai(sdnwmyE27*a8l<x_97vQY2|
z+FO3dfv_R#oy6qOkjI8?d1_)Dg|Aw4gx_E-)>*s=Kay_nvIBZlROCU(@S!zd$l(`z
zjrFKy9mWm+7taX{S!gk<<)NQ(5Hb+<*}cWt(|*=LeG}I5D~wN`YlJLOKl#P8OY0Q+
zqdpV9g!s4`b;D}-<?8M7)iaPG=Y6I_Y};enFwQ&$Ik?HvnRMs`o;3g$w!w~&o6=AR
z$F?z<QI;lMgzezj^qB?Z`|~SIQ%*BIfY|NFoZf#$O`YqUv4ObyEAm#izz(muJx6rW
zFJJvH@cLvG;?5}3pr{{Ed+qObi+DzTh&O%RsQ-?WuNV9E)(d?({m0S&3h9GxtV#5}
z0va=s3nx<AW#plnx2@Pjm#Z;HJhye&Hek{103UBUv=EoJoX7YHw|_8%xscJCa{~Rp
z!akiAy-)f((H}?u%hvwN4^BDrUq=5)Ti$NSB%UL^VU}_#kSAv`t(e8qy=bqfK)-?h
zl27#;99&VNP;U!MPr`S)Z^gN-gwBR&-j+d}wJzvoY(MOBu*cq~hOPEvm#lu&LsCYA
z&~0RrJlKnKO~i1}lm=v89K-oHLOx-Kr)3U}4d7hy%=iv!_5supW0!#8+hxSkMA&*4
zX!Lvwa65;F-(<Py87`^yBhDELodvJmE%Xh@85%ohulqYcmvs>tr%aq#OmUsXem%Fq
z7BF`;=&i;c!>2Hgm~#%aC-oyf!)DGg&Kl1iRy;6;e+#)_&t5IR(n!3Az!@pp-Iq{P
z;8{o1L9{vx{w3@L?*j5($JwFw#2)g<6)x?$h4fR$Z5~dwSTRuWQWC8qz1QgnU)1w3
z)3;GeVt;$>n~>)a>^u%Q4qZTgyz`)m5vF^-#<Uc5WaD1gc$HPtQ`*Cbb0b*ul;Z7*
zad1E-*C_+KT4CjCS5Hj7+AZ41LppT71au=S5i1|J=F@5D!J!pc(qhd`v_oTC73z+1
zurjPrm(Ib<Va3<2v-B>WB_0f8Pvku4O2iG3YeQqzim%JSdlNDCJ=%1pii1;#B6!ZB
z3TB$R0Q!H3rS-%m>vM_2MO1b6CvLrBi979)e)n9|K!H0=@?SOZ4rd5D!<pR~Wom0-
zDgup1Owe7Wq+t(QM|jWi$4rmSLCz}1dj-^`8-f_W4?N(!D+LeBaNoqG;NRCxRQN^<
z2j2*j-a|r9at!trDuO%*vCnz%G*uUK#9ZW$-?H?EpivARG=XOW_eHQ*@aWjdHq;F1
zhrN`45&Rsg(eh^^-#;-I`EZV%7m*WZ)CUswBW#EKJ-K+Ffm-k5_w4r><I~ezf}VJ$
zhTXv?wS|Yl8)%4p3mc?47Of$RR%q<&;BgjUHsCJ6j{x<6zXoIgCIZp{X@GwOOaL4M
zya*8f=LV>NMt}l%0?+}dhwl5u`!l=)^IK<Q-6IDi-m#g;pQx#XZWO)OL=9tV%@xR@
zeRl2y?{pM4V(HF~CzjnTwEM6oma)CQPRIysTJt>B{i1E{{VnVr9%1s}*;&|zXjfg0
zkOy_0-~s%|qp&k+zbW2rQa)nn_CAvw`j`h=TVAtcusA<)xn&zCf0G(WY9OhBqy~~2
zNNOOdfushK8c1p&sez;hk{b9w)_}|2Kkuiv)Fn6(_hYyc?HhQi^h3&YTHlnuNAsNf
z*-{lv!{;?$;VM|9RQjZXfK-Q%S&HT36R6-%=^-~27|OFQDkvc`sbH}>d5KgIbWO>!
zb}(uFRwe!;n!iJCp5hi=rqeIJVZ!JRSIRoY`ko2jJmEjGF`~S*1miZ&n`JGbJiL7r
zSKd_zC%%}noBvC{?6C>q6_s^yo`ZD<=R4T%;Dru091J~(i^C4CaB#%I8ysBa;O{%w
zbZ~=%qYmEZ;3fw*JGjNcZ4Qn(xXZzD2cL6rzk}a#@Q{PA+Bo@})Id@LNev`5@c&l>
zBHv~j022@+5;;5z?JTsj(9T9X8|`egv(fgVEiSKNA@Z6Ij@kGo8_`XM(>5I(6WBG|
zHP5xc6?E;u-_tIi^A`i|a{ZgrIs*JN*Ll~o_R2rxH$sy6hs?+K)K~2JZhXT;MTxbb
zGemj#*A+=EiN4R^(L|3Yar1>Z;*5M%?D4oL4e-@279W@6694Xy^Q3=KuRydLm;Eie
ddl5P$=RSaYl`^Nzn>H_SUl%<&nrjoF{{f0owX6UD
literal 0
HcmV?d00001
diff --git a/arch/arm/boards/multilink/env/bin/init_board b/arch/arm/boards/multilink/env/bin/init_board
new file mode 100644
index 0000000..96ece8d
--- /dev/null
+++ b/arch/arm/boards/multilink/env/bin/init_board
@@ -0,0 +1,4 @@
+#!/bin/sh
+
+mkdir /firmware
+cp /env/NPE-B /firmware
--
1.7.9.1
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* Re: [PATCH 00/10] IXP4xx rebase WIP
2012-04-23 6:56 [PATCH 00/10] IXP4xx rebase WIP Jean-Christophe PLAGNIOL-VILLARD
` (9 preceding siblings ...)
2012-04-23 7:02 ` [PATCH 10/10] multilink: " Jean-Christophe PLAGNIOL-VILLARD
@ 2012-04-24 8:08 ` Sascha Hauer
2012-04-28 8:32 ` Krzysztof Halasa
10 siblings, 1 reply; 13+ messages in thread
From: Sascha Hauer @ 2012-04-24 8:08 UTC (permalink / raw)
To: Jean-Christophe PLAGNIOL-VILLARD; +Cc: barebox, Krzysztof Halasa
Hi Krzysztof,
Since you pinged me recently about ixp4xx support, could you have a look
at it first and say if you are happy with it?
Thanks
Sascha
On Mon, Apr 23, 2012 at 08:56:50AM +0200, Jean-Christophe PLAGNIOL-VILLARD wrote:
> HI,
>
> the followong patch serie is a rebase of the ixp4xx support send
> by Krzysztof sometimes ago
>
> I test it on NSLU2 via JTAG only
>
> The following changes since commit a7ddbc40865a8ffe716aca686763780febad575c:
>
> Merge branch 'binfmt' of git://git.jcrosoft.org/barebox into next (2012-04-18 20:42:17 +0200)
>
> are available in the git repository at:
>
>
> git://git.jcrosoft.org/barebox.git ixp4xx-wip
>
> for you to fetch changes up to 0ab89e4ef3057f5d5e19606cc229aad4f614aca6:
>
> multilink: NPE-B firmware + boot script (2012-04-23 15:14:45 +0800)
>
> ----------------------------------------------------------------
> Jean-Christophe PLAGNIOL-VILLARD (6):
> ARM: add support of in_be16/32 and out_be16/32
> ixp4xx: add gpio support
> ixp4xx: add generic board lowlevel_init
> ARM: Add support for Linksys NSLU2 support
> nslu2: NPE-B firmware + boot script
> multilink: NPE-B firmware + boot script
>
> Krzysztof Hałasa (4):
> ARM: Add support for IXP4xx CPU
> ARM: Add support for IXP4xx Network Process Engine and queue Manager support
> net: Add support for IXP4xx ethernet support
> ARM: Add support for Goramo Multilink router platform.
>
> Documentation/boards.dox | 1 +
> arch/arm/Kconfig | 9 +
> arch/arm/Makefile | 3 +
> arch/arm/boards/multilink/Makefile | 1 +
> arch/arm/boards/multilink/env/NPE-B | Bin 0 -> 11964 bytes
> arch/arm/boards/multilink/env/bin/init_board | 4 +
> arch/arm/boards/multilink/env/config | 36 ++
> arch/arm/boards/multilink/lowlevel_init.S | 64 ++
> arch/arm/boards/multilink/multilink.c | 131 +++++
> arch/arm/boards/multilink/multilink.dox | 36 ++
> arch/arm/boards/nslu2/Makefile | 1 +
> arch/arm/boards/nslu2/config.h | 6 +
> arch/arm/boards/nslu2/env/NPE-B | Bin 0 -> 11964 bytes
> arch/arm/boards/nslu2/env/bin/init_board | 4 +
> arch/arm/boards/nslu2/env/config | 36 ++
> arch/arm/boards/nslu2/init.c | 171 ++++++
> arch/arm/configs/multilink_defconfig | 55 ++
> arch/arm/configs/nslu2_defconfig | 65 +++
> arch/arm/cpu/Kconfig | 6 +-
> arch/arm/include/asm/io.h | 5 +
> arch/arm/mach-ixp4xx/Kconfig | 40 ++
> arch/arm/mach-ixp4xx/Makefile | 8 +
> arch/arm/mach-ixp4xx/board_lowlevel_init.c | 58 ++
> arch/arm/mach-ixp4xx/devices.c | 95 +++
> arch/arm/mach-ixp4xx/include/mach/cpu.h | 70 +++
> arch/arm/mach-ixp4xx/include/mach/gpio.h | 69 +++
> arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h | 365 ++++++++++++
> arch/arm/mach-ixp4xx/include/mach/npe.h | 30 +
> arch/arm/mach-ixp4xx/include/mach/platform.h | 86 +++
> arch/arm/mach-ixp4xx/include/mach/qmgr.h | 164 ++++++
> arch/arm/mach-ixp4xx/lowlevel_init.S | 25 +
> arch/arm/mach-ixp4xx/npe.c | 668 ++++++++++++++++++++++
> arch/arm/mach-ixp4xx/qmgr.c | 259 +++++++++
> arch/arm/mach-ixp4xx/reset.c | 15 +
> arch/arm/mach-ixp4xx/timer.c | 42 ++
> drivers/net/Kconfig | 8 +
> drivers/net/Makefile | 1 +
> drivers/net/ixp4xx_eth.c | 699 +++++++++++++++++++++++
> drivers/serial/serial_ns16550.c | 6 +-
> drivers/serial/serial_ns16550.h | 2 +
> 40 files changed, 3342 insertions(+), 2 deletions(-)
> create mode 100644 arch/arm/boards/multilink/Makefile
> create mode 100644 arch/arm/boards/multilink/config.h
> create mode 100644 arch/arm/boards/multilink/env/NPE-B
> create mode 100644 arch/arm/boards/multilink/env/bin/init_board
> create mode 100644 arch/arm/boards/multilink/env/config
> create mode 100644 arch/arm/boards/multilink/lowlevel_init.S
> create mode 100644 arch/arm/boards/multilink/multilink.c
> create mode 100644 arch/arm/boards/multilink/multilink.dox
> create mode 100644 arch/arm/boards/nslu2/Makefile
> create mode 100644 arch/arm/boards/nslu2/config.h
> create mode 100644 arch/arm/boards/nslu2/env/NPE-B
> create mode 100644 arch/arm/boards/nslu2/env/bin/init_board
> create mode 100644 arch/arm/boards/nslu2/env/config
> create mode 100644 arch/arm/boards/nslu2/init.c
> create mode 100644 arch/arm/configs/multilink_defconfig
> create mode 100644 arch/arm/configs/nslu2_defconfig
> create mode 100644 arch/arm/mach-ixp4xx/Kconfig
> create mode 100644 arch/arm/mach-ixp4xx/Makefile
> create mode 100644 arch/arm/mach-ixp4xx/board_lowlevel_init.c
> create mode 100644 arch/arm/mach-ixp4xx/devices.c
> create mode 100644 arch/arm/mach-ixp4xx/include/mach/cpu.h
> create mode 100644 arch/arm/mach-ixp4xx/include/mach/gpio.h
> create mode 100644 arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h
> create mode 100644 arch/arm/mach-ixp4xx/include/mach/npe.h
> create mode 100644 arch/arm/mach-ixp4xx/include/mach/platform.h
> create mode 100644 arch/arm/mach-ixp4xx/include/mach/qmgr.h
> create mode 100644 arch/arm/mach-ixp4xx/lowlevel_init.S
> create mode 100644 arch/arm/mach-ixp4xx/npe.c
> create mode 100644 arch/arm/mach-ixp4xx/qmgr.c
> create mode 100644 arch/arm/mach-ixp4xx/reset.c
> create mode 100644 arch/arm/mach-ixp4xx/timer.c
> create mode 100644 drivers/net/ixp4xx_eth.c
>
> Best Regards,
> J.
>
> _______________________________________________
> barebox mailing list
> barebox@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* Re: [PATCH 00/10] IXP4xx rebase WIP
2012-04-24 8:08 ` [PATCH 00/10] IXP4xx rebase WIP Sascha Hauer
@ 2012-04-28 8:32 ` Krzysztof Halasa
0 siblings, 0 replies; 13+ messages in thread
From: Krzysztof Halasa @ 2012-04-28 8:32 UTC (permalink / raw)
To: Sascha Hauer; +Cc: barebox
Hi,
Sascha Hauer <s.hauer@pengutronix.de> writes:
> Since you pinged me recently about ixp4xx support, could you have a look
> at it first and say if you are happy with it?
Will do. Actually I've ported my old patches to the recent Barebox,
though I intend to polish them a bit before I send them out. I will
check them against these from Jean-Christophe. This will probably take
a couple of days or so.
I have doubt WRT one thing, namely the NPE microcode (and its licence).
They (Intel) seem to allow binary redistribution (we don't have the
sources anyway) but they request an acknowledgment (I guess both in
Barebox sources, and in/with the Barebox image in the actual system).
--
Krzysztof Halasa
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread