* [FIXES Master] tny-a926x fixes
@ 2012-04-24 10:09 Jean-Christophe PLAGNIOL-VILLARD
2012-04-24 10:15 ` [PATCH 1/2] at91: at91_register_uart use number instead of IDs Jean-Christophe PLAGNIOL-VILLARD
` (2 more replies)
0 siblings, 3 replies; 4+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-04-24 10:09 UTC (permalink / raw)
To: barebox
HI,
the following patch series fix the Calao tny-a926x
this is for the master branch
The following changes since commit 1d79f322f7a3bff9b6b9bde4ce7f391f0316063a:
mtd: docg3 fixes backport from Linux kernel (2012-04-17 22:02:54 +0200)
are available in the git repository at:
git://git.jcrosoft.org/barebox.git master-fixes
for you to fetch changes up to 60e03c64b0c7e6f3aedcf2c9328aa105de3ba11d:
tny-a926x: fix MOB-TNY-MD2 Motherboard support (2012-04-24 18:27:32 +0800)
----------------------------------------------------------------
Jean-Christophe PLAGNIOL-VILLARD (2):
at91: at91_register_uart use number instead of IDs
tny-a926x: fix MOB-TNY-MD2 Motherboard support
arch/arm/boards/tny-a926x/init.c | 38 +++--------------------------
arch/arm/configs/tny_a9260_defconfig | 2 +-
arch/arm/configs/tny_a9263_defconfig | 2 +-
arch/arm/configs/tny_a9g20_defconfig | 2 +-
arch/arm/mach-at91/Kconfig | 10 ++++++++
arch/arm/mach-at91/at91rm9200_devices.c | 13 +++-------
arch/arm/mach-at91/at91sam9260_devices.c | 19 ++++----------
arch/arm/mach-at91/at91sam9261_devices.c | 10 ++-----
arch/arm/mach-at91/at91sam9263_devices.c | 10 ++-----
arch/arm/mach-at91/at91sam9g45_devices.c | 13 +++-------
10 files changed, 37 insertions(+), 82 deletions(-)
Best Regards,
J.
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH 1/2] at91: at91_register_uart use number instead of IDs
2012-04-24 10:09 [FIXES Master] tny-a926x fixes Jean-Christophe PLAGNIOL-VILLARD
@ 2012-04-24 10:15 ` Jean-Christophe PLAGNIOL-VILLARD
2012-04-24 10:15 ` [PATCH 2/2] tny-a926x: fix MOB-TNY-MD2 Motherboard support Jean-Christophe PLAGNIOL-VILLARD
2012-04-24 13:20 ` [FIXES Master] tny-a926x fixes Sascha Hauer
2 siblings, 0 replies; 4+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-04-24 10:15 UTC (permalink / raw)
To: barebox
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
arch/arm/mach-at91/at91rm9200_devices.c | 13 ++++---------
arch/arm/mach-at91/at91sam9260_devices.c | 19 ++++++-------------
arch/arm/mach-at91/at91sam9261_devices.c | 10 +++-------
arch/arm/mach-at91/at91sam9263_devices.c | 10 +++-------
arch/arm/mach-at91/at91sam9g45_devices.c | 13 ++++---------
5 files changed, 20 insertions(+), 45 deletions(-)
diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c
index c380c7d..7e721e5 100644
--- a/arch/arm/mach-at91/at91rm9200_devices.c
+++ b/arch/arm/mach-at91/at91rm9200_devices.c
@@ -273,27 +273,22 @@ struct device_d * __init at91_register_uart(unsigned id, unsigned pins)
case 0: /* DBGU */
configure_dbgu_pins();
start = AT91_BASE_SYS + AT91_DBGU;
- id = 0;
break;
- case AT91RM9200_ID_US0:
+ case 1:
configure_usart0_pins(pins);
start = AT91RM9200_BASE_US0;
- id = 1;
break;
- case AT91RM9200_ID_US1:
+ case 2:
configure_usart1_pins(pins);
start = AT91RM9200_BASE_US1;
- id = 2;
break;
- case AT91RM9200_ID_US2:
+ case 3:
configure_usart2_pins(pins);
start = AT91RM9200_BASE_US2;
- id = 3;
break;
- case AT91RM9200_ID_US3:
+ case 4:
configure_usart3_pins(pins);
start = AT91RM9200_BASE_US3;
- id = 4;
break;
default:
return NULL;
diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c
index 23da8c1..17dbd1a 100644
--- a/arch/arm/mach-at91/at91sam9260_devices.c
+++ b/arch/arm/mach-at91/at91sam9260_devices.c
@@ -290,37 +290,30 @@ struct device_d * __init at91_register_uart(unsigned id, unsigned pins)
case 0: /* DBGU */
configure_dbgu_pins();
start = AT91_BASE_SYS + AT91_DBGU;
- id = 0;
break;
- case AT91SAM9260_ID_US0:
+ case 1:
configure_usart0_pins(pins);
start = AT91SAM9260_BASE_US0;
- id = 1;
break;
- case AT91SAM9260_ID_US1:
+ case 2:
configure_usart1_pins(pins);
start = AT91SAM9260_BASE_US1;
- id = 2;
break;
- case AT91SAM9260_ID_US2:
+ case 3:
configure_usart2_pins(pins);
start = AT91SAM9260_BASE_US2;
- id = 3;
break;
- case AT91SAM9260_ID_US3:
+ case 4:
configure_usart3_pins(pins);
start = AT91SAM9260_BASE_US3;
- id = 4;
break;
- case AT91SAM9260_ID_US4:
+ case 5:
configure_usart4_pins();
start = AT91SAM9260_BASE_US4;
- id = 5;
break;
- case AT91SAM9260_ID_US5:
+ case 6:
configure_usart5_pins();
start = AT91SAM9260_BASE_US5;
- id = 6;
break;
default:
return NULL;
diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c
index d4f7b5e..8a63d2a 100644
--- a/arch/arm/mach-at91/at91sam9261_devices.c
+++ b/arch/arm/mach-at91/at91sam9261_devices.c
@@ -211,22 +211,18 @@ struct device_d * __init at91_register_uart(unsigned id, unsigned pins)
case 0: /* DBGU */
configure_dbgu_pins();
start = AT91_BASE_SYS + AT91_DBGU;
- id = 0;
break;
- case AT91SAM9261_ID_US0:
+ case 1:
configure_usart0_pins(pins);
start = AT91SAM9261_BASE_US0;
- id = 1;
break;
- case AT91SAM9261_ID_US1:
+ case 2:
configure_usart1_pins(pins);
start = AT91SAM9261_BASE_US1;
- id = 2;
break;
- case AT91SAM9261_ID_US2:
+ case 3:
configure_usart2_pins(pins);
start = AT91SAM9261_BASE_US2;
- id = 3;
break;
default:
return NULL;
diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
index 12d6a24..b28e9e2 100644
--- a/arch/arm/mach-at91/at91sam9263_devices.c
+++ b/arch/arm/mach-at91/at91sam9263_devices.c
@@ -261,22 +261,18 @@ struct device_d * __init at91_register_uart(unsigned id, unsigned pins)
case 0: /* DBGU */
configure_dbgu_pins();
start = AT91_BASE_SYS + AT91_DBGU;
- id = 0;
break;
- case AT91SAM9263_ID_US0:
+ case 1:
configure_usart0_pins(pins);
start = AT91SAM9263_BASE_US0;
- id = 1;
break;
- case AT91SAM9263_ID_US1:
+ case 2:
configure_usart1_pins(pins);
start = AT91SAM9263_BASE_US1;
- id = 2;
break;
- case AT91SAM9263_ID_US2:
+ case 3:
configure_usart2_pins(pins);
start = AT91SAM9263_BASE_US2;
- id = 3;
break;
default:
return NULL;
diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c
index 25a8d80..ca96f58 100644
--- a/arch/arm/mach-at91/at91sam9g45_devices.c
+++ b/arch/arm/mach-at91/at91sam9g45_devices.c
@@ -190,27 +190,22 @@ struct device_d * __init at91_register_uart(unsigned id, unsigned pins)
case 0: /* DBGU */
configure_dbgu_pins();
start = AT91_BASE_SYS + AT91_DBGU;
- id = 0;
break;
- case AT91SAM9G45_ID_US0:
+ case 1:
configure_usart0_pins(pins);
start = AT91SAM9G45_BASE_US0;
- id = 1;
break;
- case AT91SAM9G45_ID_US1:
+ case 2:
configure_usart1_pins(pins);
start = AT91SAM9G45_BASE_US1;
- id = 2;
break;
- case AT91SAM9G45_ID_US2:
+ case 3:
configure_usart2_pins(pins);
start = AT91SAM9G45_BASE_US2;
- id = 3;
break;
- case AT91SAM9G45_ID_US3:
+ case 4:
configure_usart3_pins(pins);
start = AT91SAM9G45_BASE_US3;
- id = 4;
break;
default:
return NULL;
--
1.7.9.1
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH 2/2] tny-a926x: fix MOB-TNY-MD2 Motherboard support
2012-04-24 10:09 [FIXES Master] tny-a926x fixes Jean-Christophe PLAGNIOL-VILLARD
2012-04-24 10:15 ` [PATCH 1/2] at91: at91_register_uart use number instead of IDs Jean-Christophe PLAGNIOL-VILLARD
@ 2012-04-24 10:15 ` Jean-Christophe PLAGNIOL-VILLARD
2012-04-24 13:20 ` [FIXES Master] tny-a926x fixes Sascha Hauer
2 siblings, 0 replies; 4+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-04-24 10:15 UTC (permalink / raw)
To: barebox
The MD2 add:
- uart 2
- ethernet
- usb
- spi
- i2c
so fix just add uart and ethernet
update defconfig
always enable the motherboard and drop the SHA256 support (to fix in the
256KiB).
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
arch/arm/boards/tny-a926x/init.c | 38 +++------------------------------
arch/arm/configs/tny_a9260_defconfig | 2 +-
arch/arm/configs/tny_a9263_defconfig | 2 +-
arch/arm/configs/tny_a9g20_defconfig | 2 +-
arch/arm/mach-at91/Kconfig | 10 +++++++++
5 files changed, 17 insertions(+), 37 deletions(-)
diff --git a/arch/arm/boards/tny-a926x/init.c b/arch/arm/boards/tny-a926x/init.c
index 2065eae..eeaca76 100644
--- a/arch/arm/boards/tny-a926x/init.c
+++ b/arch/arm/boards/tny-a926x/init.c
@@ -121,42 +121,10 @@ static struct at91_ether_platform_data macb_pdata = {
.phy_addr = 0,
};
-static void tny_a9260_phy_reset(void)
-{
- unsigned long rstc;
- struct clk *clk = clk_get(NULL, "macb_clk");
-
- clk_enable(clk);
-
- at91_set_gpio_input(AT91_PIN_PA14, 0);
- at91_set_gpio_input(AT91_PIN_PA15, 0);
- at91_set_gpio_input(AT91_PIN_PA17, 0);
- at91_set_gpio_input(AT91_PIN_PA25, 0);
- at91_set_gpio_input(AT91_PIN_PA26, 0);
- at91_set_gpio_input(AT91_PIN_PA28, 0);
-
- rstc = at91_sys_read(AT91_RSTC_MR) & AT91_RSTC_ERSTL;
-
- /* Need to reset PHY -> 500ms reset */
- at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
- (AT91_RSTC_ERSTL & (0x0d << 8)) |
- AT91_RSTC_URSTEN);
-
- at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_EXTRST);
-
- /* Wait for end hardware reset */
- while (!(at91_sys_read(AT91_RSTC_SR) & AT91_RSTC_NRSTL));
-
- /* Restore NRST value */
- at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
- (rstc) |
- AT91_RSTC_URSTEN);
-}
-
static void __init ek_add_device_macb(void)
{
- tny_a9260_phy_reset();
- at91_add_device_eth(0, &macb_pdata);
+ if (IS_ENABLED(CONFIG_CALAO_MOB_TNY_MD2))
+ at91_add_device_eth(0, &macb_pdata);
}
#else
static void __init ek_add_device_macb(void) {}
@@ -240,6 +208,8 @@ device_initcall(tny_a9260_devices_init);
static int tny_a9260_console_init(void)
{
at91_register_uart(0, 0);
+ if (IS_ENABLED(CONFIG_CALAO_MOB_TNY_MD2))
+ at91_register_uart(2, ATMEL_UART_CTS | ATMEL_UART_RTS);
return 0;
}
console_initcall(tny_a9260_console_init);
diff --git a/arch/arm/configs/tny_a9260_defconfig b/arch/arm/configs/tny_a9260_defconfig
index 52bd7e4..2388305 100644
--- a/arch/arm/configs/tny_a9260_defconfig
+++ b/arch/arm/configs/tny_a9260_defconfig
@@ -1,5 +1,6 @@
CONFIG_ARCH_AT91SAM9260=y
CONFIG_MACH_TNY_A9260=y
+CONFIG_CALAO_MOB_TNY_MD2=y
CONFIG_AEABI=y
# CONFIG_CMD_ARM_CPUINFO is not set
CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y
@@ -33,7 +34,6 @@ CONFIG_CMD_LOADB=y
CONFIG_CMD_MEMINFO=y
CONFIG_CMD_MD5SUM=y
CONFIG_CMD_SHA1SUM=y
-CONFIG_CMD_SHA256SUM=y
CONFIG_CMD_MTEST=y
CONFIG_CMD_MTEST_ALTERNATIVE=y
CONFIG_CMD_FLASH=y
diff --git a/arch/arm/configs/tny_a9263_defconfig b/arch/arm/configs/tny_a9263_defconfig
index 1c316c8..d1bc418 100644
--- a/arch/arm/configs/tny_a9263_defconfig
+++ b/arch/arm/configs/tny_a9263_defconfig
@@ -1,5 +1,6 @@
CONFIG_ARCH_AT91SAM9263=y
CONFIG_MACH_TNY_A9263=y
+CONFIG_CALAO_MOB_TNY_MD2=y
CONFIG_AEABI=y
# CONFIG_CMD_ARM_CPUINFO is not set
CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y
@@ -33,7 +34,6 @@ CONFIG_CMD_LOADB=y
CONFIG_CMD_MEMINFO=y
CONFIG_CMD_MD5SUM=y
CONFIG_CMD_SHA1SUM=y
-CONFIG_CMD_SHA256SUM=y
CONFIG_CMD_MTEST=y
CONFIG_CMD_MTEST_ALTERNATIVE=y
CONFIG_CMD_FLASH=y
diff --git a/arch/arm/configs/tny_a9g20_defconfig b/arch/arm/configs/tny_a9g20_defconfig
index f842382..983c68a 100644
--- a/arch/arm/configs/tny_a9g20_defconfig
+++ b/arch/arm/configs/tny_a9g20_defconfig
@@ -1,5 +1,6 @@
CONFIG_ARCH_AT91SAM9G20=y
CONFIG_MACH_TNY_A9G20=y
+CONFIG_CALAO_MOB_TNY_MD2=y
CONFIG_AEABI=y
# CONFIG_CMD_ARM_CPUINFO is not set
CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y
@@ -33,7 +34,6 @@ CONFIG_CMD_LOADB=y
CONFIG_CMD_MEMINFO=y
CONFIG_CMD_MD5SUM=y
CONFIG_CMD_SHA1SUM=y
-CONFIG_CMD_SHA256SUM=y
CONFIG_CMD_MTEST=y
CONFIG_CMD_MTEST_ALTERNATIVE=y
CONFIG_CMD_FLASH=y
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index 989d3d8..1bec3e5 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -104,6 +104,9 @@ config ARCH_BAREBOX_MAX_BARE_INIT_SIZE
config SUPPORT_CALAO_DAB_MMX
bool
+config SUPPORT_CALAO_MOB_TNY_MD2
+ bool
+
# ----------------------------------------------------------
if ARCH_AT91RM9200
@@ -138,6 +141,7 @@ config MACH_AT91SAM9260EK
config MACH_TNY_A9260
bool "CALAO TNY-A9260"
+ select SUPPORT_CALAO_MOB_TNY_MD2
help
Select this if you are using a Calao Systems TNY-A9260.
<http://www.calao-systems.com>
@@ -214,6 +218,7 @@ config MACH_AT91SAM9G20EK
that embeds only one SD/MMC slot.
config MACH_TNY_A9G20
+ select SUPPORT_CALAO_MOB_TNY_MD2
bool "CALAO TNY-A9G20"
help
Select this if you are using a Calao Systems TNY-A9G20.
@@ -264,6 +269,7 @@ config MACH_PM9263
config MACH_TNY_A9263
bool "CALAO TNY-A9263"
+ select SUPPORT_CALAO_MOB_TNY_MD2
help
Select this if you are using a Calao Systems TNY-A9263.
<http://www.calao-systems.com>
@@ -362,4 +368,8 @@ config CALAO_DAB_MMX
bool "DAB MMX Daughter Board support"
depends on SUPPORT_CALAO_DAB_MMX
+config CALAO_MOB_TNY_MD2
+ bool "MOB TNY MD2 Motherboard Daughter Board support"
+ depends on SUPPORT_CALAO_MOB_TNY_MD2
+
endif
--
1.7.9.1
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [FIXES Master] tny-a926x fixes
2012-04-24 10:09 [FIXES Master] tny-a926x fixes Jean-Christophe PLAGNIOL-VILLARD
2012-04-24 10:15 ` [PATCH 1/2] at91: at91_register_uart use number instead of IDs Jean-Christophe PLAGNIOL-VILLARD
2012-04-24 10:15 ` [PATCH 2/2] tny-a926x: fix MOB-TNY-MD2 Motherboard support Jean-Christophe PLAGNIOL-VILLARD
@ 2012-04-24 13:20 ` Sascha Hauer
2 siblings, 0 replies; 4+ messages in thread
From: Sascha Hauer @ 2012-04-24 13:20 UTC (permalink / raw)
To: Jean-Christophe PLAGNIOL-VILLARD; +Cc: barebox
On Tue, Apr 24, 2012 at 12:09:16PM +0200, Jean-Christophe PLAGNIOL-VILLARD wrote:
> HI,
>
> the following patch series fix the Calao tny-a926x
>
> this is for the master branch
>
> The following changes since commit 1d79f322f7a3bff9b6b9bde4ce7f391f0316063a:
>
> mtd: docg3 fixes backport from Linux kernel (2012-04-17 22:02:54 +0200)
>
> are available in the git repository at:
>
> git://git.jcrosoft.org/barebox.git master-fixes
>
> for you to fetch changes up to 60e03c64b0c7e6f3aedcf2c9328aa105de3ba11d:
pulled, thanks
Sascha
>
> tny-a926x: fix MOB-TNY-MD2 Motherboard support (2012-04-24 18:27:32 +0800)
>
> ----------------------------------------------------------------
> Jean-Christophe PLAGNIOL-VILLARD (2):
> at91: at91_register_uart use number instead of IDs
> tny-a926x: fix MOB-TNY-MD2 Motherboard support
>
> arch/arm/boards/tny-a926x/init.c | 38 +++--------------------------
> arch/arm/configs/tny_a9260_defconfig | 2 +-
> arch/arm/configs/tny_a9263_defconfig | 2 +-
> arch/arm/configs/tny_a9g20_defconfig | 2 +-
> arch/arm/mach-at91/Kconfig | 10 ++++++++
> arch/arm/mach-at91/at91rm9200_devices.c | 13 +++-------
> arch/arm/mach-at91/at91sam9260_devices.c | 19 ++++----------
> arch/arm/mach-at91/at91sam9261_devices.c | 10 ++-----
> arch/arm/mach-at91/at91sam9263_devices.c | 10 ++-----
> arch/arm/mach-at91/at91sam9g45_devices.c | 13 +++-------
> 10 files changed, 37 insertions(+), 82 deletions(-)
>
> Best Regards,
> J.
>
> _______________________________________________
> barebox mailing list
> barebox@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
>
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2012-04-24 13:20 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2012-04-24 10:09 [FIXES Master] tny-a926x fixes Jean-Christophe PLAGNIOL-VILLARD
2012-04-24 10:15 ` [PATCH 1/2] at91: at91_register_uart use number instead of IDs Jean-Christophe PLAGNIOL-VILLARD
2012-04-24 10:15 ` [PATCH 2/2] tny-a926x: fix MOB-TNY-MD2 Motherboard support Jean-Christophe PLAGNIOL-VILLARD
2012-04-24 13:20 ` [FIXES Master] tny-a926x fixes Sascha Hauer
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox