* [PATCH 0/7 v3] smsc911x: runtime configuration improvement
@ 2012-09-01 8:47 Jean-Christophe PLAGNIOL-VILLARD
2012-09-01 8:52 ` [PATCH 1/7] smc911x: move register define to smc911x.h Jean-Christophe PLAGNIOL-VILLARD
2012-09-03 7:49 ` [PATCH 0/7 v3] smsc911x: runtime configuration improvement Sascha Hauer
0 siblings, 2 replies; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-09-01 8:47 UTC (permalink / raw)
To: barebox
Hi,
v3:
update commnets
v2:
update 16/32bit callback
please pull
The following changes since commit 3f96b4938c4046590be8a38fb114148c4bf1ca8e:
Merge tag 'bootm_fix' of git://git.jcrosoft.org/barebox (2012-08-13 20:37:53 +0200)
are available in the git repository at:
git://git.jcrosoft.org/barebox.git tags/smc911x_improve
for you to fetch changes up to f3cbf3104561580a2edc46aa6ad2c8167141709d:
smc911x: check if the device is ready before using it (2012-09-01 16:37:01 +0800)
----------------------------------------------------------------
smsc911x: runtime configuration improvement
This patch series allow to detect and configure the drivers at the runtime
- Check if the device is ready before using it
- Update chip detection (take from the kernel 3.5)
- improve detection handle to detect bus configuration and swap
- add support to pass the shift via platform data
- add 16bit bus width support
- introduce read/write ops
- move register define to smc911x.h
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
----------------------------------------------------------------
Jean-Christophe PLAGNIOL-VILLARD (7):
smc911x: move register define to smc911x.h
smc911x: introduce read/write ops
smc911x: add 16bit bus width support
smc911x: add support to pass the shift via platform data
smc911x: improve detection handle
smc911x: update chip detection
smc911x: check if the device is ready before using it
arch/blackfin/boards/ipe337/ipe337.c | 7 +-
drivers/net/Kconfig | 6 -
drivers/net/smc911x.c | 589 ++++++++++++++++++++++++++++++++-------------------------------------------------------------
drivers/net/smc911x.h | 342 ++++++++++++++++++++++++++++++++++++++++++++++++++++++
include/smc911x.h | 18 +++
5 files changed, 565 insertions(+), 397 deletions(-)
create mode 100644 drivers/net/smc911x.h
create mode 100644 include/smc911x.h
Best Regards,
J.
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* [PATCH 1/7] smc911x: move register define to smc911x.h 2012-09-01 8:47 [PATCH 0/7 v3] smsc911x: runtime configuration improvement Jean-Christophe PLAGNIOL-VILLARD @ 2012-09-01 8:52 ` Jean-Christophe PLAGNIOL-VILLARD 2012-09-01 8:52 ` [PATCH 2/7] smc911x: introduce read/write ops Jean-Christophe PLAGNIOL-VILLARD ` (5 more replies) 2012-09-03 7:49 ` [PATCH 0/7 v3] smsc911x: runtime configuration improvement Sascha Hauer 1 sibling, 6 replies; 13+ messages in thread From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-09-01 8:52 UTC (permalink / raw) To: barebox this make the driver more readable Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> --- drivers/net/smc911x.c | 329 +-------------------------- drivers/net/{smc911x.c => smc911x.h} | 406 ---------------------------------- 2 files changed, 2 insertions(+), 733 deletions(-) copy drivers/net/{smc911x.c => smc911x.h} (60%) diff --git a/drivers/net/smc911x.c b/drivers/net/smc911x.c index 7dddbbc..9c488c7 100644 --- a/drivers/net/smc911x.c +++ b/drivers/net/smc911x.c @@ -38,334 +38,9 @@ #include <clock.h> #include <io.h> -#define AS CONFIG_DRIVER_NET_SMC911X_ADDRESS_SHIFT -/* Below are the register offsets and bit definitions - * of the Lan911x memory space - */ -#define RX_DATA_FIFO (0x00 << AS) - -#define TX_DATA_FIFO (0x20 << AS) -#define TX_CMD_A_INT_ON_COMP 0x80000000 -#define TX_CMD_A_INT_BUF_END_ALGN 0x03000000 -#define TX_CMD_A_INT_4_BYTE_ALGN 0x00000000 -#define TX_CMD_A_INT_16_BYTE_ALGN 0x01000000 -#define TX_CMD_A_INT_32_BYTE_ALGN 0x02000000 -#define TX_CMD_A_INT_DATA_OFFSET 0x001F0000 -#define TX_CMD_A_INT_FIRST_SEG 0x00002000 -#define TX_CMD_A_INT_LAST_SEG 0x00001000 -#define TX_CMD_A_BUF_SIZE 0x000007FF -#define TX_CMD_B_PKT_TAG 0xFFFF0000 -#define TX_CMD_B_ADD_CRC_DISABLE 0x00002000 -#define TX_CMD_B_DISABLE_PADDING 0x00001000 -#define TX_CMD_B_PKT_BYTE_LENGTH 0x000007FF - -#define RX_STATUS_FIFO (0x40 << AS) -#define RX_STS_PKT_LEN 0x3FFF0000 -#define RX_STS_ES 0x00008000 -#define RX_STS_BCST 0x00002000 -#define RX_STS_LEN_ERR 0x00001000 -#define RX_STS_RUNT_ERR 0x00000800 -#define RX_STS_MCAST 0x00000400 -#define RX_STS_TOO_LONG 0x00000080 -#define RX_STS_COLL 0x00000040 -#define RX_STS_ETH_TYPE 0x00000020 -#define RX_STS_WDOG_TMT 0x00000010 -#define RX_STS_MII_ERR 0x00000008 -#define RX_STS_DRIBBLING 0x00000004 -#define RX_STS_CRC_ERR 0x00000002 -#define RX_STATUS_FIFO_PEEK (0x44 << AS) -#define TX_STATUS_FIFO (0x48 << AS) -#define TX_STS_TAG 0xFFFF0000 -#define TX_STS_ES 0x00008000 -#define TX_STS_LOC 0x00000800 -#define TX_STS_NO_CARR 0x00000400 -#define TX_STS_LATE_COLL 0x00000200 -#define TX_STS_MANY_COLL 0x00000100 -#define TX_STS_COLL_CNT 0x00000078 -#define TX_STS_MANY_DEFER 0x00000004 -#define TX_STS_UNDERRUN 0x00000002 -#define TX_STS_DEFERRED 0x00000001 -#define TX_STATUS_FIFO_PEEK (0x4C << AS) -#define ID_REV (0x50 << AS) -#define ID_REV_CHIP_ID 0xFFFF0000 /* RO */ -#define ID_REV_REV_ID 0x0000FFFF /* RO */ - -#define INT_CFG (0x54 << AS) -#define INT_CFG_INT_DEAS 0xFF000000 /* R/W */ -#define INT_CFG_INT_DEAS_CLR 0x00004000 -#define INT_CFG_INT_DEAS_STS 0x00002000 -#define INT_CFG_IRQ_INT 0x00001000 /* RO */ -#define INT_CFG_IRQ_EN 0x00000100 /* R/W */ -#define INT_CFG_IRQ_POL 0x00000010 /* R/W Not Affected by SW Reset */ -#define INT_CFG_IRQ_TYPE 0x00000001 /* R/W Not Affected by SW Reset */ - -#define INT_STS (0x58 << AS) -#define INT_STS_SW_INT 0x80000000 /* R/WC */ -#define INT_STS_TXSTOP_INT 0x02000000 /* R/WC */ -#define INT_STS_RXSTOP_INT 0x01000000 /* R/WC */ -#define INT_STS_RXDFH_INT 0x00800000 /* R/WC */ -#define INT_STS_RXDF_INT 0x00400000 /* R/WC */ -#define INT_STS_TX_IOC 0x00200000 /* R/WC */ -#define INT_STS_RXD_INT 0x00100000 /* R/WC */ -#define INT_STS_GPT_INT 0x00080000 /* R/WC */ -#define INT_STS_PHY_INT 0x00040000 /* RO */ -#define INT_STS_PME_INT 0x00020000 /* R/WC */ -#define INT_STS_TXSO 0x00010000 /* R/WC */ -#define INT_STS_RWT 0x00008000 /* R/WC */ -#define INT_STS_RXE 0x00004000 /* R/WC */ -#define INT_STS_TXE 0x00002000 /* R/WC */ -//#define INT_STS_ERX 0x00001000 /* R/WC */ -#define INT_STS_TDFU 0x00000800 /* R/WC */ -#define INT_STS_TDFO 0x00000400 /* R/WC */ -#define INT_STS_TDFA 0x00000200 /* R/WC */ -#define INT_STS_TSFF 0x00000100 /* R/WC */ -#define INT_STS_TSFL 0x00000080 /* R/WC */ -//#define INT_STS_RXDF 0x00000040 /* R/WC */ -#define INT_STS_RDFO 0x00000040 /* R/WC */ -#define INT_STS_RDFL 0x00000020 /* R/WC */ -#define INT_STS_RSFF 0x00000010 /* R/WC */ -#define INT_STS_RSFL 0x00000008 /* R/WC */ -#define INT_STS_GPIO2_INT 0x00000004 /* R/WC */ -#define INT_STS_GPIO1_INT 0x00000002 /* R/WC */ -#define INT_STS_GPIO0_INT 0x00000001 /* R/WC */ -#define INT_EN (0x5C << AS) -#define INT_EN_SW_INT_EN 0x80000000 /* R/W */ -#define INT_EN_TXSTOP_INT_EN 0x02000000 /* R/W */ -#define INT_EN_RXSTOP_INT_EN 0x01000000 /* R/W */ -#define INT_EN_RXDFH_INT_EN 0x00800000 /* R/W */ -//#define INT_EN_RXDF_INT_EN 0x00400000 /* R/W */ -#define INT_EN_TIOC_INT_EN 0x00200000 /* R/W */ -#define INT_EN_RXD_INT_EN 0x00100000 /* R/W */ -#define INT_EN_GPT_INT_EN 0x00080000 /* R/W */ -#define INT_EN_PHY_INT_EN 0x00040000 /* R/W */ -#define INT_EN_PME_INT_EN 0x00020000 /* R/W */ -#define INT_EN_TXSO_EN 0x00010000 /* R/W */ -#define INT_EN_RWT_EN 0x00008000 /* R/W */ -#define INT_EN_RXE_EN 0x00004000 /* R/W */ -#define INT_EN_TXE_EN 0x00002000 /* R/W */ -//#define INT_EN_ERX_EN 0x00001000 /* R/W */ -#define INT_EN_TDFU_EN 0x00000800 /* R/W */ -#define INT_EN_TDFO_EN 0x00000400 /* R/W */ -#define INT_EN_TDFA_EN 0x00000200 /* R/W */ -#define INT_EN_TSFF_EN 0x00000100 /* R/W */ -#define INT_EN_TSFL_EN 0x00000080 /* R/W */ -//#define INT_EN_RXDF_EN 0x00000040 /* R/W */ -#define INT_EN_RDFO_EN 0x00000040 /* R/W */ -#define INT_EN_RDFL_EN 0x00000020 /* R/W */ -#define INT_EN_RSFF_EN 0x00000010 /* R/W */ -#define INT_EN_RSFL_EN 0x00000008 /* R/W */ -#define INT_EN_GPIO2_INT 0x00000004 /* R/W */ -#define INT_EN_GPIO1_INT 0x00000002 /* R/W */ -#define INT_EN_GPIO0_INT 0x00000001 /* R/W */ - -#define BYTE_TEST (0x64 << AS) -#define FIFO_INT (0x68 << AS) -#define FIFO_INT_TX_AVAIL_LEVEL 0xFF000000 /* R/W */ -#define FIFO_INT_TX_STS_LEVEL 0x00FF0000 /* R/W */ -#define FIFO_INT_RX_AVAIL_LEVEL 0x0000FF00 /* R/W */ -#define FIFO_INT_RX_STS_LEVEL 0x000000FF /* R/W */ - -#define RX_CFG (0x6C << AS) -#define RX_CFG_RX_END_ALGN 0xC0000000 /* R/W */ -#define RX_CFG_RX_END_ALGN4 0x00000000 /* R/W */ -#define RX_CFG_RX_END_ALGN16 0x40000000 /* R/W */ -#define RX_CFG_RX_END_ALGN32 0x80000000 /* R/W */ -#define RX_CFG_RX_DMA_CNT 0x0FFF0000 /* R/W */ -#define RX_CFG_RX_DUMP 0x00008000 /* R/W */ -#define RX_CFG_RXDOFF 0x00001F00 /* R/W */ -//#define RX_CFG_RXBAD 0x00000001 /* R/W */ - -#define TX_CFG (0x70 << AS) -//#define TX_CFG_TX_DMA_LVL 0xE0000000 /* R/W */ -//#define TX_CFG_TX_DMA_CNT 0x0FFF0000 /* R/W Self Clearing */ -#define TX_CFG_TXS_DUMP 0x00008000 /* Self Clearing */ -#define TX_CFG_TXD_DUMP 0x00004000 /* Self Clearing */ -#define TX_CFG_TXSAO 0x00000004 /* R/W */ -#define TX_CFG_TX_ON 0x00000002 /* R/W */ -#define TX_CFG_STOP_TX 0x00000001 /* Self Clearing */ - -#define HW_CFG (0x74 << AS) -#define HW_CFG_TTM 0x00200000 /* R/W */ -#define HW_CFG_SF 0x00100000 /* R/W */ -#define HW_CFG_TX_FIF_SZ 0x000F0000 /* R/W */ -#define HW_CFG_TR 0x00003000 /* R/W */ -#define HW_CFG_PHY_CLK_SEL 0x00000060 /* R/W */ -#define HW_CFG_PHY_CLK_SEL_INT_PHY 0x00000000 /* R/W */ -#define HW_CFG_PHY_CLK_SEL_EXT_PHY 0x00000020 /* R/W */ -#define HW_CFG_PHY_CLK_SEL_CLK_DIS 0x00000040 /* R/W */ -#define HW_CFG_SMI_SEL 0x00000010 /* R/W */ -#define HW_CFG_EXT_PHY_DET 0x00000008 /* RO */ -#define HW_CFG_EXT_PHY_EN 0x00000004 /* R/W */ -#define HW_CFG_32_16_BIT_MODE 0x00000004 /* RO */ -#define HW_CFG_SRST_TO 0x00000002 /* RO */ -#define HW_CFG_SRST 0x00000001 /* Self Clearing */ - -#define RX_DP_CTRL (0x78 << AS) -#define RX_DP_CTRL_RX_FFWD 0x80000000 /* R/W */ -#define RX_DP_CTRL_FFWD_BUSY 0x80000000 /* RO */ - -#define RX_FIFO_INF (0x7C << AS) -#define RX_FIFO_INF_RXSUSED 0x00FF0000 /* RO */ -#define RX_FIFO_INF_RXDUSED 0x0000FFFF /* RO */ - -#define TX_FIFO_INF (0x80 << AS) -#define TX_FIFO_INF_TSUSED 0x00FF0000 /* RO */ -#define TX_FIFO_INF_TDFREE 0x0000FFFF /* RO */ - -#define PMT_CTRL (0x84 << AS) -#define PMT_CTRL_PM_MODE 0x00003000 /* Self Clearing */ -#define PMT_CTRL_PHY_RST 0x00000400 /* Self Clearing */ -#define PMT_CTRL_WOL_EN 0x00000200 /* R/W */ -#define PMT_CTRL_ED_EN 0x00000100 /* R/W */ -#define PMT_CTRL_PME_TYPE 0x00000040 /* R/W Not Affected by SW Reset */ -#define PMT_CTRL_WUPS 0x00000030 /* R/WC */ -#define PMT_CTRL_WUPS_NOWAKE 0x00000000 /* R/WC */ -#define PMT_CTRL_WUPS_ED 0x00000010 /* R/WC */ -#define PMT_CTRL_WUPS_WOL 0x00000020 /* R/WC */ -#define PMT_CTRL_WUPS_MULTI 0x00000030 /* R/WC */ -#define PMT_CTRL_PME_IND 0x00000008 /* R/W */ -#define PMT_CTRL_PME_POL 0x00000004 /* R/W */ -#define PMT_CTRL_PME_EN 0x00000002 /* R/W Not Affected by SW Reset */ -#define PMT_CTRL_READY 0x00000001 /* RO */ - -#define GPIO_CFG (0x88 << AS) -#define GPIO_CFG_LED3_EN 0x40000000 /* R/W */ -#define GPIO_CFG_LED2_EN 0x20000000 /* R/W */ -#define GPIO_CFG_LED1_EN 0x10000000 /* R/W */ -#define GPIO_CFG_GPIO2_INT_POL 0x04000000 /* R/W */ -#define GPIO_CFG_GPIO1_INT_POL 0x02000000 /* R/W */ -#define GPIO_CFG_GPIO0_INT_POL 0x01000000 /* R/W */ -#define GPIO_CFG_EEPR_EN 0x00700000 /* R/W */ -#define GPIO_CFG_GPIOBUF2 0x00040000 /* R/W */ -#define GPIO_CFG_GPIOBUF1 0x00020000 /* R/W */ -#define GPIO_CFG_GPIOBUF0 0x00010000 /* R/W */ -#define GPIO_CFG_GPIODIR2 0x00000400 /* R/W */ -#define GPIO_CFG_GPIODIR1 0x00000200 /* R/W */ -#define GPIO_CFG_GPIODIR0 0x00000100 /* R/W */ -#define GPIO_CFG_GPIOD4 0x00000010 /* R/W */ -#define GPIO_CFG_GPIOD3 0x00000008 /* R/W */ -#define GPIO_CFG_GPIOD2 0x00000004 /* R/W */ -#define GPIO_CFG_GPIOD1 0x00000002 /* R/W */ -#define GPIO_CFG_GPIOD0 0x00000001 /* R/W */ - -#define GPT_CFG (0x8C << AS) -#define GPT_CFG_TIMER_EN 0x20000000 /* R/W */ -#define GPT_CFG_GPT_LOAD 0x0000FFFF /* R/W */ - -#define GPT_CNT (0x90 << AS) -#define GPT_CNT_GPT_CNT 0x0000FFFF /* RO */ - -#define ENDIAN (0x98 << AS) -#define FREE_RUN (0x9C << AS) -#define RX_DROP (0xA0 << AS) -#define MAC_CSR_CMD (0xA4 << AS) -#define MAC_CSR_CMD_CSR_BUSY 0x80000000 /* Self Clearing */ -#define MAC_CSR_CMD_R_NOT_W 0x40000000 /* R/W */ -#define MAC_CSR_CMD_CSR_ADDR 0x000000FF /* R/W */ - -#define MAC_CSR_DATA (0xA8 << AS) -#define AFC_CFG (0xAC << AS) -#define AFC_CFG_AFC_HI 0x00FF0000 /* R/W */ -#define AFC_CFG_AFC_LO 0x0000FF00 /* R/W */ -#define AFC_CFG_BACK_DUR 0x000000F0 /* R/W */ -#define AFC_CFG_FCMULT 0x00000008 /* R/W */ -#define AFC_CFG_FCBRD 0x00000004 /* R/W */ -#define AFC_CFG_FCADD 0x00000002 /* R/W */ -#define AFC_CFG_FCANY 0x00000001 /* R/W */ - -#define E2P_CMD (0xB0 << AS) -#define E2P_CMD_EPC_BUSY 0x80000000 /* Self Clearing */ -#define E2P_CMD_EPC_CMD 0x70000000 /* R/W */ -#define E2P_CMD_EPC_CMD_READ 0x00000000 /* R/W */ -#define E2P_CMD_EPC_CMD_EWDS 0x10000000 /* R/W */ -#define E2P_CMD_EPC_CMD_EWEN 0x20000000 /* R/W */ -#define E2P_CMD_EPC_CMD_WRITE 0x30000000 /* R/W */ -#define E2P_CMD_EPC_CMD_WRAL 0x40000000 /* R/W */ -#define E2P_CMD_EPC_CMD_ERASE 0x50000000 /* R/W */ -#define E2P_CMD_EPC_CMD_ERAL 0x60000000 /* R/W */ -#define E2P_CMD_EPC_CMD_RELOAD 0x70000000 /* R/W */ -#define E2P_CMD_EPC_TIMEOUT 0x00000200 /* RO */ -#define E2P_CMD_MAC_ADDR_LOADED 0x00000100 /* RO */ -#define E2P_CMD_EPC_ADDR 0x000000FF /* R/W */ - -#define E2P_DATA (0xB4 << AS) -#define E2P_DATA_EEPROM_DATA 0x000000FF /* R/W */ -/* end of LAN register offsets and bit definitions */ - -/* MAC Control and Status registers */ -#define MAC_CR 0x01 /* R/W */ - -/* MAC_CR - MAC Control Register */ -#define MAC_CR_RXALL 0x80000000 -// TODO: delete this bit? It is not described in the data sheet. -#define MAC_CR_HBDIS 0x10000000 -#define MAC_CR_RCVOWN 0x00800000 -#define MAC_CR_LOOPBK 0x00200000 -#define MAC_CR_FDPX 0x00100000 -#define MAC_CR_MCPAS 0x00080000 -#define MAC_CR_PRMS 0x00040000 -#define MAC_CR_INVFILT 0x00020000 -#define MAC_CR_PASSBAD 0x00010000 -#define MAC_CR_HFILT 0x00008000 -#define MAC_CR_HPFILT 0x00002000 -#define MAC_CR_LCOLL 0x00001000 -#define MAC_CR_BCAST 0x00000800 -#define MAC_CR_DISRTY 0x00000400 -#define MAC_CR_PADSTR 0x00000100 -#define MAC_CR_BOLMT_MASK 0x000000C0 -#define MAC_CR_DFCHK 0x00000020 -#define MAC_CR_TXEN 0x00000008 -#define MAC_CR_RXEN 0x00000004 - -#define ADDRH 0x02 /* R/W mask 0x0000FFFFUL */ -#define ADDRL 0x03 /* R/W mask 0xFFFFFFFFUL */ -#define HASHH 0x04 /* R/W */ -#define HASHL 0x05 /* R/W */ - -#define MII_ACC 0x06 /* R/W */ -#define MII_ACC_PHY_ADDR 0x0000F800 -#define MII_ACC_MIIRINDA 0x000007C0 -#define MII_ACC_MII_WRITE 0x00000002 -#define MII_ACC_MII_BUSY 0x00000001 - -#define MII_DATA 0x07 /* R/W mask 0x0000FFFFUL */ - -#ifdef FLOW -#undef FLOW /* clashed with include/asm/cpu/defBF561.h:1654 */ -#endif - -#define FLOW 0x08 /* R/W */ -#define FLOW_FCPT 0xFFFF0000 -#define FLOW_FCPASS 0x00000004 -#define FLOW_FCEN 0x00000002 -#define FLOW_FCBSY 0x00000001 - -#define VLAN1 0x09 /* R/W mask 0x0000FFFFUL */ -#define VLAN1_VTI1 0x0000ffff - -#define VLAN2 0x0A /* R/W mask 0x0000FFFFUL */ -#define VLAN2_VTI2 0x0000ffff - -#define WUFF 0x0B /* WO */ - -#define WUCSR 0x0C /* R/W */ -#define WUCSR_GUE 0x00000200 -#define WUCSR_WUFR 0x00000040 -#define WUCSR_MPR 0x00000020 -#define WUCSR_WAKE_EN 0x00000004 -#define WUCSR_MPEN 0x00000002 - -/* Chip ID values */ -#define CHIP_9115 0x115 -#define CHIP_9116 0x116 -#define CHIP_9117 0x117 -#define CHIP_9118 0x118 -#define CHIP_9215 0x115a -#define CHIP_9216 0x116a -#define CHIP_9217 0x117a -#define CHIP_9218 0x118a -#define CHIP_9221 0x9221 +#define AS CONFIG_DRIVER_NET_SMC911X_ADDRESS_SHIFT +#include "smc911x.h" struct smc911x_priv { struct eth_device edev; diff --git a/drivers/net/smc911x.c b/drivers/net/smc911x.h similarity index 60% copy from drivers/net/smc911x.c copy to drivers/net/smc911x.h index 7dddbbc..68f6590 100644 --- a/drivers/net/smc911x.c +++ b/drivers/net/smc911x.h @@ -22,24 +22,6 @@ * MA 02111-1307 USA */ -#ifdef CONFIG_ENABLE_DEVICE_NOISE -# define DEBUG -#endif - -#include <common.h> - -#include <command.h> -#include <net.h> -#include <miidev.h> -#include <malloc.h> -#include <init.h> -#include <xfuncs.h> -#include <errno.h> -#include <clock.h> -#include <io.h> - -#define AS CONFIG_DRIVER_NET_SMC911X_ADDRESS_SHIFT - /* Below are the register offsets and bit definitions * of the Lan911x memory space */ @@ -367,392 +349,4 @@ #define CHIP_9218 0x118a #define CHIP_9221 0x9221 -struct smc911x_priv { - struct eth_device edev; - struct mii_device miidev; - void __iomem *base; -}; - -struct chip_id { - u16 id; - char *name; -}; - -static const struct chip_id chip_ids[] = { - { CHIP_9115, "LAN9115" }, - { CHIP_9116, "LAN9116" }, - { CHIP_9117, "LAN9117" }, - { CHIP_9118, "LAN9118" }, - { CHIP_9215, "LAN9215" }, - { CHIP_9216, "LAN9216" }, - { CHIP_9217, "LAN9217" }, - { CHIP_9218, "LAN9218" }, - { CHIP_9221, "LAN9221" }, - { 0, NULL }, -}; - -#define DRIVERNAME "smc911x" - -static int smc911x_mac_wait_busy(struct smc911x_priv *priv) -{ - uint64_t start = get_time_ns(); - - while (!is_timeout(start, MSECOND)) { - if (!(readl(priv->base + MAC_CSR_CMD) & MAC_CSR_CMD_CSR_BUSY)) - return 0; - } - - printf("%s: mac timeout\n", __FUNCTION__); - return -1; -} - -static u32 smc911x_get_mac_csr(struct eth_device *edev, u8 reg) -{ - struct smc911x_priv *priv = edev->priv; - ulong val; - - smc911x_mac_wait_busy(priv); - - writel(MAC_CSR_CMD_CSR_BUSY | MAC_CSR_CMD_R_NOT_W | reg, - priv->base + MAC_CSR_CMD); - - smc911x_mac_wait_busy(priv); - - val = readl(priv->base + MAC_CSR_DATA); - - return val; -} - -static void smc911x_set_mac_csr(struct eth_device *edev, u8 reg, u32 data) -{ - struct smc911x_priv *priv = edev->priv; - - smc911x_mac_wait_busy(priv); - - writel(data, priv->base + MAC_CSR_DATA); - writel(MAC_CSR_CMD_CSR_BUSY | reg, priv->base + MAC_CSR_CMD); - - smc911x_mac_wait_busy(priv); -} - -static int smc911x_get_ethaddr(struct eth_device *edev, unsigned char *m) -{ - unsigned long addrh, addrl; - - addrh = smc911x_get_mac_csr(edev, ADDRH); - addrl = smc911x_get_mac_csr(edev, ADDRL); - - m[0] = (addrl ) & 0xff; - m[1] = (addrl >> 8 ) & 0xff; - m[2] = (addrl >> 16 ) & 0xff; - m[3] = (addrl >> 24 ) & 0xff; - m[4] = (addrh ) & 0xff; - m[5] = (addrh >> 8 ) & 0xff; - - /* we get 0xff when there is no eeprom connected */ - if ((m[0] & m[1] & m[2] & m[3] & m[4] & m[5]) == 0xff) - return -1; - - return 0; -} - -static int smc911x_set_ethaddr(struct eth_device *edev, unsigned char *m) -{ - unsigned long addrh, addrl; - - addrl = m[0] | m[1] << 8 | m[2] << 16 | m[3] << 24; - addrh = m[4] | m[5] << 8; - smc911x_set_mac_csr(edev, ADDRH, addrh); - smc911x_set_mac_csr(edev, ADDRL, addrl); - - return 0; -} - -static int smc911x_phy_read(struct mii_device *mdev, int phy_addr, int reg) -{ - struct eth_device *edev = mdev->edev; - - while (smc911x_get_mac_csr(edev, MII_ACC) & MII_ACC_MII_BUSY); - - smc911x_set_mac_csr(edev, MII_ACC, phy_addr << 11 | reg << 6 | - MII_ACC_MII_BUSY); - - while (smc911x_get_mac_csr(edev, MII_ACC) & MII_ACC_MII_BUSY); - - return smc911x_get_mac_csr(edev, MII_DATA); -} - -static int smc911x_phy_write(struct mii_device *mdev, int phy_addr, - int reg, int val) -{ - struct eth_device *edev = mdev->edev; - - while (smc911x_get_mac_csr(edev, MII_ACC) & MII_ACC_MII_BUSY); - - smc911x_set_mac_csr(edev, MII_DATA, val); - smc911x_set_mac_csr(edev, MII_ACC, - phy_addr << 11 | reg << 6 | MII_ACC_MII_BUSY | - MII_ACC_MII_WRITE); - - while (smc911x_get_mac_csr(edev, MII_ACC) & MII_ACC_MII_BUSY); - - return 0; -} - -static int smc911x_phy_reset(struct eth_device *edev) -{ - struct smc911x_priv *priv = edev->priv; - u32 reg; - - reg = readl(priv->base + PMT_CTRL); - reg &= 0xfcf; - reg |= PMT_CTRL_PHY_RST; - writel(reg, priv->base + PMT_CTRL); - - mdelay(100); - - return 0; -} - -static void smc911x_reset(struct eth_device *edev) -{ - struct smc911x_priv *priv = edev->priv; - uint64_t start; - - /* Take out of PM setting first */ - if (readl(priv->base + PMT_CTRL) & PMT_CTRL_READY) { - /* Write to the bytetest will take out of powerdown */ - writel(0, priv->base + BYTE_TEST); - - start = get_time_ns(); - while(1) { - if ((readl(priv->base + PMT_CTRL) & PMT_CTRL_READY)) - break; - if (is_timeout(start, 100 * USECOND)) { - dev_err(&edev->dev, - "timeout waiting for PM restore\n"); - return; - } - } - } - - /* Disable interrupts */ - writel(0, priv->base + INT_EN); - - writel(HW_CFG_SRST, priv->base + HW_CFG); - - start = get_time_ns(); - while(1) { - if (!(readl(priv->base + E2P_CMD) & E2P_CMD_EPC_BUSY)) - break; - if (is_timeout(start, 10 * MSECOND)) { - dev_err(&edev->dev, "reset timeout\n"); - return; - } - } - - /* Reset the FIFO level and flow control settings */ - smc911x_set_mac_csr(edev, FLOW, FLOW_FCPT | FLOW_FCEN); - - writel(0x0050287F, priv->base + AFC_CFG); - - /* Set to LED outputs */ - writel(0x70070000, priv->base + GPIO_CFG); -} - -static void smc911x_enable(struct eth_device *edev) -{ - struct smc911x_priv *priv = edev->priv; - - /* Enable TX */ - writel(8 << 16 | HW_CFG_SF, priv->base + HW_CFG); - - writel(GPT_CFG_TIMER_EN | 10000, priv->base + GPT_CFG); - - writel(TX_CFG_TX_ON, priv->base + TX_CFG); - - /* no padding to start of packets */ - writel(RX_CFG_RX_DUMP, priv->base + RX_CFG); -} - -static int smc911x_eth_open(struct eth_device *edev) -{ - struct smc911x_priv *priv = (struct smc911x_priv *)edev->priv; - - miidev_wait_aneg(&priv->miidev); - miidev_print_status(&priv->miidev); - - /* Turn on Tx + Rx */ - smc911x_enable(edev); - return 0; -} - -static int smc911x_eth_send(struct eth_device *edev, void *packet, int length) -{ - struct smc911x_priv *priv = (struct smc911x_priv *)edev->priv; - u32 *data = (u32*)packet; - u32 tmplen; - u32 status; - uint64_t start; - - writel(TX_CMD_A_INT_FIRST_SEG | TX_CMD_A_INT_LAST_SEG | length, - priv->base + TX_DATA_FIFO); - writel(length, priv->base + TX_DATA_FIFO); - - tmplen = (length + 3) / 4; - - while(tmplen--) - writel(*data++, priv->base + TX_DATA_FIFO); - - /* wait for transmission */ - start = get_time_ns(); - while (1) { - if ((readl(priv->base + TX_FIFO_INF) & - TX_FIFO_INF_TSUSED) >> 16) - break; - if (is_timeout(start, 100 * MSECOND)) { - dev_err(&edev->dev, "TX timeout\n"); - return -1; - } - } - - /* get status. Ignore 'no carrier' error, it has no meaning for - * full duplex operation - */ - status = readl(priv->base + TX_STATUS_FIFO) & (TX_STS_LOC | - TX_STS_LATE_COLL | TX_STS_MANY_COLL | TX_STS_MANY_DEFER | - TX_STS_UNDERRUN); - - if(!status) - return 0; - - dev_err(&edev->dev, "failed to send packet: %s%s%s%s%s\n", - status & TX_STS_LOC ? "TX_STS_LOC " : "", - status & TX_STS_LATE_COLL ? "TX_STS_LATE_COLL " : "", - status & TX_STS_MANY_COLL ? "TX_STS_MANY_COLL " : "", - status & TX_STS_MANY_DEFER ? "TX_STS_MANY_DEFER " : "", - status & TX_STS_UNDERRUN ? "TX_STS_UNDERRUN" : ""); - - return -1; -} - -static void smc911x_eth_halt(struct eth_device *edev) -{ - struct smc911x_priv *priv = (struct smc911x_priv *)edev->priv; - - /* Disable TX */ - writel(TX_CFG_STOP_TX, priv->base + TX_CFG); - -// smc911x_reset(edev); -} - -static int smc911x_eth_rx(struct eth_device *edev) -{ - struct smc911x_priv *priv = (struct smc911x_priv *)edev->priv; - u32 *data = (u32 *)NetRxPackets[0]; - u32 pktlen, tmplen; - u32 status; - - if((readl(priv->base + RX_FIFO_INF) & RX_FIFO_INF_RXSUSED) >> 16) { - status = readl(priv->base + RX_STATUS_FIFO); - pktlen = (status & RX_STS_PKT_LEN) >> 16; - - writel(0, priv->base + RX_CFG); - - tmplen = (pktlen + 2 + 3) / 4; - while(tmplen--) - *data++ = readl(priv->base + RX_DATA_FIFO); - - if(status & RX_STS_ES) - dev_err(&edev->dev, "dropped bad packet. Status: 0x%08x\n", - status); - else - net_receive(NetRxPackets[0], pktlen); - } - - return 0; -} - -static int smc911x_init_dev(struct eth_device *edev) -{ - struct smc911x_priv *priv = (struct smc911x_priv *)edev->priv; - - smc911x_set_mac_csr(edev, MAC_CR, MAC_CR_TXEN | MAC_CR_RXEN | - MAC_CR_HBDIS); - - miidev_restart_aneg(&priv->miidev); - - return 0; -} - -static int smc911x_probe(struct device_d *dev) -{ - struct eth_device *edev; - struct smc911x_priv *priv; - uint32_t val; - int i; - void __iomem *base; - - base = dev_request_mem_region(dev, 0); - - val = readl(base + BYTE_TEST); - if(val != 0x87654321) { - dev_err(dev, "no smc911x found on 0x%p (byte_test=0x%08x)\n", - base, val); - return -ENODEV; - } - - val = readl(base + ID_REV) >> 16; - for(i = 0; chip_ids[i].id != 0; i++) { - if (chip_ids[i].id == val) break; - } - if (!chip_ids[i].id) { - dev_err(dev, "Unknown chip ID %04x\n", val); - return -ENODEV; - } - - dev_info(dev, "detected %s controller\n", chip_ids[i].name); - - priv = xzalloc(sizeof(*priv)); - edev = &priv->edev; - edev->priv = priv; - - edev->init = smc911x_init_dev; - edev->open = smc911x_eth_open; - edev->send = smc911x_eth_send; - edev->recv = smc911x_eth_rx; - edev->halt = smc911x_eth_halt; - edev->get_ethaddr = smc911x_get_ethaddr; - edev->set_ethaddr = smc911x_set_ethaddr; - edev->parent = dev; - - priv->miidev.read = smc911x_phy_read; - priv->miidev.write = smc911x_phy_write; - priv->miidev.address = 1; - priv->miidev.flags = 0; - priv->miidev.edev = edev; - priv->miidev.parent = dev; - priv->base = base; - - smc911x_reset(edev); - smc911x_phy_reset(edev); - - mii_register(&priv->miidev); - eth_register(edev); - - return 0; -} - -static struct driver_d smc911x_driver = { - .name = "smc911x", - .probe = smc911x_probe, -}; - -static int smc911x_init(void) -{ - register_driver(&smc911x_driver); - return 0; -} - -device_initcall(smc911x_init); -- 1.7.10.4 _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH 2/7] smc911x: introduce read/write ops 2012-09-01 8:52 ` [PATCH 1/7] smc911x: move register define to smc911x.h Jean-Christophe PLAGNIOL-VILLARD @ 2012-09-01 8:52 ` Jean-Christophe PLAGNIOL-VILLARD 2012-09-01 8:52 ` [PATCH 3/7] smc911x: add 16bit bus width support Jean-Christophe PLAGNIOL-VILLARD ` (4 subsequent siblings) 5 siblings, 0 replies; 13+ messages in thread From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-09-01 8:52 UTC (permalink / raw) To: barebox This will allow to replace them depending on the platform data. So we can specify shift and reg io witdh (16bit/32bit) Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> --- drivers/net/smc911x.c | 101 ++++++++++++++++++++++++++++++------------------- 1 file changed, 63 insertions(+), 38 deletions(-) diff --git a/drivers/net/smc911x.c b/drivers/net/smc911x.c index 9c488c7..2583235 100644 --- a/drivers/net/smc911x.c +++ b/drivers/net/smc911x.c @@ -46,6 +46,9 @@ struct smc911x_priv { struct eth_device edev; struct mii_device miidev; void __iomem *base; + + u32 (*reg_read)(struct smc911x_priv *priv, u32 reg); + void (*reg_write)(struct smc911x_priv *priv, u32 reg, u32 val); }; struct chip_id { @@ -68,12 +71,34 @@ static const struct chip_id chip_ids[] = { #define DRIVERNAME "smc911x" +static inline u32 smc911x_reg_read(struct smc911x_priv *priv, u32 reg) +{ + return priv->reg_read(priv, reg); +} + +static inline u32 __smc911x_reg_read(struct smc911x_priv *priv, u32 reg) +{ + return readl(priv->base + reg); +} + +static inline void smc911x_reg_write(struct smc911x_priv *priv, u32 reg, + u32 val) +{ + priv->reg_write(priv, reg, val); +} + +static inline void __smc911x_reg_write(struct smc911x_priv *priv, u32 reg, + u32 val) +{ + writel(val, priv->base + reg); +} + static int smc911x_mac_wait_busy(struct smc911x_priv *priv) { uint64_t start = get_time_ns(); while (!is_timeout(start, MSECOND)) { - if (!(readl(priv->base + MAC_CSR_CMD) & MAC_CSR_CMD_CSR_BUSY)) + if (!(smc911x_reg_read(priv, MAC_CSR_CMD) & MAC_CSR_CMD_CSR_BUSY)) return 0; } @@ -88,12 +113,12 @@ static u32 smc911x_get_mac_csr(struct eth_device *edev, u8 reg) smc911x_mac_wait_busy(priv); - writel(MAC_CSR_CMD_CSR_BUSY | MAC_CSR_CMD_R_NOT_W | reg, - priv->base + MAC_CSR_CMD); + smc911x_reg_write(priv, MAC_CSR_CMD, MAC_CSR_CMD_CSR_BUSY | + MAC_CSR_CMD_R_NOT_W | reg); smc911x_mac_wait_busy(priv); - val = readl(priv->base + MAC_CSR_DATA); + val = smc911x_reg_read(priv, MAC_CSR_DATA); return val; } @@ -104,8 +129,8 @@ static void smc911x_set_mac_csr(struct eth_device *edev, u8 reg, u32 data) smc911x_mac_wait_busy(priv); - writel(data, priv->base + MAC_CSR_DATA); - writel(MAC_CSR_CMD_CSR_BUSY | reg, priv->base + MAC_CSR_CMD); + smc911x_reg_write(priv, MAC_CSR_DATA, data); + smc911x_reg_write(priv, MAC_CSR_CMD, MAC_CSR_CMD_CSR_BUSY | reg); smc911x_mac_wait_busy(priv); } @@ -179,10 +204,10 @@ static int smc911x_phy_reset(struct eth_device *edev) struct smc911x_priv *priv = edev->priv; u32 reg; - reg = readl(priv->base + PMT_CTRL); + reg = smc911x_reg_read(priv, PMT_CTRL); reg &= 0xfcf; reg |= PMT_CTRL_PHY_RST; - writel(reg, priv->base + PMT_CTRL); + smc911x_reg_write(priv, PMT_CTRL, reg); mdelay(100); @@ -195,13 +220,13 @@ static void smc911x_reset(struct eth_device *edev) uint64_t start; /* Take out of PM setting first */ - if (readl(priv->base + PMT_CTRL) & PMT_CTRL_READY) { + if (smc911x_reg_read(priv, PMT_CTRL) & PMT_CTRL_READY) { /* Write to the bytetest will take out of powerdown */ - writel(0, priv->base + BYTE_TEST); + smc911x_reg_write(priv, BYTE_TEST, 0); start = get_time_ns(); while(1) { - if ((readl(priv->base + PMT_CTRL) & PMT_CTRL_READY)) + if ((smc911x_reg_read(priv, PMT_CTRL) & PMT_CTRL_READY)) break; if (is_timeout(start, 100 * USECOND)) { dev_err(&edev->dev, @@ -212,13 +237,13 @@ static void smc911x_reset(struct eth_device *edev) } /* Disable interrupts */ - writel(0, priv->base + INT_EN); + smc911x_reg_write(priv, INT_EN, 0); - writel(HW_CFG_SRST, priv->base + HW_CFG); + smc911x_reg_write(priv, HW_CFG, HW_CFG_SRST); start = get_time_ns(); while(1) { - if (!(readl(priv->base + E2P_CMD) & E2P_CMD_EPC_BUSY)) + if (!(smc911x_reg_read(priv, E2P_CMD) & E2P_CMD_EPC_BUSY)) break; if (is_timeout(start, 10 * MSECOND)) { dev_err(&edev->dev, "reset timeout\n"); @@ -229,10 +254,10 @@ static void smc911x_reset(struct eth_device *edev) /* Reset the FIFO level and flow control settings */ smc911x_set_mac_csr(edev, FLOW, FLOW_FCPT | FLOW_FCEN); - writel(0x0050287F, priv->base + AFC_CFG); + smc911x_reg_write(priv, AFC_CFG, 0x0050287F); /* Set to LED outputs */ - writel(0x70070000, priv->base + GPIO_CFG); + smc911x_reg_write(priv, GPIO_CFG, 0x70070000); } static void smc911x_enable(struct eth_device *edev) @@ -240,14 +265,14 @@ static void smc911x_enable(struct eth_device *edev) struct smc911x_priv *priv = edev->priv; /* Enable TX */ - writel(8 << 16 | HW_CFG_SF, priv->base + HW_CFG); + smc911x_reg_write(priv, HW_CFG, 8 << 16 | HW_CFG_SF); - writel(GPT_CFG_TIMER_EN | 10000, priv->base + GPT_CFG); + smc911x_reg_write(priv, GPT_CFG, GPT_CFG_TIMER_EN | 10000); - writel(TX_CFG_TX_ON, priv->base + TX_CFG); + smc911x_reg_write(priv, TX_CFG, TX_CFG_TX_ON); /* no padding to start of packets */ - writel(RX_CFG_RX_DUMP, priv->base + RX_CFG); + smc911x_reg_write(priv, RX_CFG, RX_CFG_RX_DUMP); } static int smc911x_eth_open(struct eth_device *edev) @@ -270,19 +295,19 @@ static int smc911x_eth_send(struct eth_device *edev, void *packet, int length) u32 status; uint64_t start; - writel(TX_CMD_A_INT_FIRST_SEG | TX_CMD_A_INT_LAST_SEG | length, - priv->base + TX_DATA_FIFO); - writel(length, priv->base + TX_DATA_FIFO); + smc911x_reg_write(priv, TX_DATA_FIFO, + TX_CMD_A_INT_FIRST_SEG | TX_CMD_A_INT_LAST_SEG | length); + smc911x_reg_write(priv, TX_DATA_FIFO, length); tmplen = (length + 3) / 4; while(tmplen--) - writel(*data++, priv->base + TX_DATA_FIFO); + smc911x_reg_write(priv, TX_DATA_FIFO, *data++); /* wait for transmission */ start = get_time_ns(); while (1) { - if ((readl(priv->base + TX_FIFO_INF) & + if ((smc911x_reg_read(priv, TX_FIFO_INF) & TX_FIFO_INF_TSUSED) >> 16) break; if (is_timeout(start, 100 * MSECOND)) { @@ -294,7 +319,7 @@ static int smc911x_eth_send(struct eth_device *edev, void *packet, int length) /* get status. Ignore 'no carrier' error, it has no meaning for * full duplex operation */ - status = readl(priv->base + TX_STATUS_FIFO) & (TX_STS_LOC | + status = smc911x_reg_read(priv, TX_STATUS_FIFO) & (TX_STS_LOC | TX_STS_LATE_COLL | TX_STS_MANY_COLL | TX_STS_MANY_DEFER | TX_STS_UNDERRUN); @@ -316,7 +341,7 @@ static void smc911x_eth_halt(struct eth_device *edev) struct smc911x_priv *priv = (struct smc911x_priv *)edev->priv; /* Disable TX */ - writel(TX_CFG_STOP_TX, priv->base + TX_CFG); + smc911x_reg_write(priv, TX_CFG, TX_CFG_STOP_TX); // smc911x_reset(edev); } @@ -328,15 +353,15 @@ static int smc911x_eth_rx(struct eth_device *edev) u32 pktlen, tmplen; u32 status; - if((readl(priv->base + RX_FIFO_INF) & RX_FIFO_INF_RXSUSED) >> 16) { - status = readl(priv->base + RX_STATUS_FIFO); + if((smc911x_reg_read(priv, RX_FIFO_INF) & RX_FIFO_INF_RXSUSED) >> 16) { + status = smc911x_reg_read(priv, RX_STATUS_FIFO); pktlen = (status & RX_STS_PKT_LEN) >> 16; - writel(0, priv->base + RX_CFG); + smc911x_reg_write(priv, RX_CFG, 0); tmplen = (pktlen + 2 + 3) / 4; while(tmplen--) - *data++ = readl(priv->base + RX_DATA_FIFO); + *data++ = smc911x_reg_read(priv, RX_DATA_FIFO); if(status & RX_STS_ES) dev_err(&edev->dev, "dropped bad packet. Status: 0x%08x\n", @@ -366,18 +391,20 @@ static int smc911x_probe(struct device_d *dev) struct smc911x_priv *priv; uint32_t val; int i; - void __iomem *base; - base = dev_request_mem_region(dev, 0); + priv = xzalloc(sizeof(*priv)); + priv->base = dev_request_mem_region(dev, 0); + priv->reg_read = __smc911x_reg_read; + priv->reg_write = __smc911x_reg_write; - val = readl(base + BYTE_TEST); + val = smc911x_reg_read(priv, BYTE_TEST); if(val != 0x87654321) { dev_err(dev, "no smc911x found on 0x%p (byte_test=0x%08x)\n", - base, val); + priv->base, val); return -ENODEV; } - val = readl(base + ID_REV) >> 16; + val = smc911x_reg_read(priv, ID_REV) >> 16; for(i = 0; chip_ids[i].id != 0; i++) { if (chip_ids[i].id == val) break; } @@ -388,7 +415,6 @@ static int smc911x_probe(struct device_d *dev) dev_info(dev, "detected %s controller\n", chip_ids[i].name); - priv = xzalloc(sizeof(*priv)); edev = &priv->edev; edev->priv = priv; @@ -407,7 +433,6 @@ static int smc911x_probe(struct device_d *dev) priv->miidev.flags = 0; priv->miidev.edev = edev; priv->miidev.parent = dev; - priv->base = base; smc911x_reset(edev); smc911x_phy_reset(edev); -- 1.7.10.4 _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH 3/7] smc911x: add 16bit bus width support 2012-09-01 8:52 ` [PATCH 1/7] smc911x: move register define to smc911x.h Jean-Christophe PLAGNIOL-VILLARD 2012-09-01 8:52 ` [PATCH 2/7] smc911x: introduce read/write ops Jean-Christophe PLAGNIOL-VILLARD @ 2012-09-01 8:52 ` Jean-Christophe PLAGNIOL-VILLARD 2012-09-01 8:52 ` [PATCH 4/7] smc911x: add support to pass the shift via platform data Jean-Christophe PLAGNIOL-VILLARD ` (3 subsequent siblings) 5 siblings, 0 replies; 13+ messages in thread From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-09-01 8:52 UTC (permalink / raw) To: barebox Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> --- drivers/net/smc911x.c | 34 +++++++++++++++++++++++++++++----- 1 file changed, 29 insertions(+), 5 deletions(-) diff --git a/drivers/net/smc911x.c b/drivers/net/smc911x.c index 2583235..917f994 100644 --- a/drivers/net/smc911x.c +++ b/drivers/net/smc911x.c @@ -76,7 +76,13 @@ static inline u32 smc911x_reg_read(struct smc911x_priv *priv, u32 reg) return priv->reg_read(priv, reg); } -static inline u32 __smc911x_reg_read(struct smc911x_priv *priv, u32 reg) +static inline u32 __smc911x_reg_readw(struct smc911x_priv *priv, u32 reg) +{ + return ((readw(priv->base + reg) & 0xFFFF) | + ((readw(priv->base + reg + 2) & 0xFFFF) << 16)); +} + +static inline u32 __smc911x_reg_readl(struct smc911x_priv *priv, u32 reg) { return readl(priv->base + reg); } @@ -87,7 +93,14 @@ static inline void smc911x_reg_write(struct smc911x_priv *priv, u32 reg, priv->reg_write(priv, reg, val); } -static inline void __smc911x_reg_write(struct smc911x_priv *priv, u32 reg, +static inline void __smc911x_reg_writew(struct smc911x_priv *priv, u32 reg, + u32 val) +{ + writew(val & 0xFFFF, priv->base + reg); + writew((val >> 16) & 0xFFFF, priv->base + reg + 2); +} + +static inline void __smc911x_reg_writel(struct smc911x_priv *priv, u32 reg, u32 val) { writel(val, priv->base + reg); @@ -390,12 +403,23 @@ static int smc911x_probe(struct device_d *dev) struct eth_device *edev; struct smc911x_priv *priv; uint32_t val; - int i; + int i, is_32bit; priv = xzalloc(sizeof(*priv)); + is_32bit = dev->resource[0].flags & IORESOURCE_MEM_TYPE_MASK; + if (!is_32bit) + is_32bit = 1; + else + is_32bit = is_32bit == IORESOURCE_MEM_32BIT; priv->base = dev_request_mem_region(dev, 0); - priv->reg_read = __smc911x_reg_read; - priv->reg_write = __smc911x_reg_write; + + if (is_32bit) { + priv->reg_read = __smc911x_reg_readl; + priv->reg_write = __smc911x_reg_writel; + } else { + priv->reg_read = __smc911x_reg_readw; + priv->reg_write = __smc911x_reg_writew; + } val = smc911x_reg_read(priv, BYTE_TEST); if(val != 0x87654321) { -- 1.7.10.4 _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH 4/7] smc911x: add support to pass the shift via platform data 2012-09-01 8:52 ` [PATCH 1/7] smc911x: move register define to smc911x.h Jean-Christophe PLAGNIOL-VILLARD 2012-09-01 8:52 ` [PATCH 2/7] smc911x: introduce read/write ops Jean-Christophe PLAGNIOL-VILLARD 2012-09-01 8:52 ` [PATCH 3/7] smc911x: add 16bit bus width support Jean-Christophe PLAGNIOL-VILLARD @ 2012-09-01 8:52 ` Jean-Christophe PLAGNIOL-VILLARD 2012-09-01 8:52 ` [PATCH 5/7] smc911x: improve detection handle Jean-Christophe PLAGNIOL-VILLARD ` (2 subsequent siblings) 5 siblings, 0 replies; 13+ messages in thread From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-09-01 8:52 UTC (permalink / raw) To: barebox switch ipe337: to it at the same time to do not brake it Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> --- arch/blackfin/boards/ipe337/ipe337.c | 7 +++- drivers/net/Kconfig | 6 ---- drivers/net/smc911x.c | 60 +++++++++++++++++++++++++++++---- drivers/net/smc911x.h | 61 +++++++++++++++++----------------- include/smc911x.h | 18 ++++++++++ 5 files changed, 109 insertions(+), 43 deletions(-) create mode 100644 include/smc911x.h diff --git a/arch/blackfin/boards/ipe337/ipe337.c b/arch/blackfin/boards/ipe337/ipe337.c index b3f07bb..9c1de2c 100644 --- a/arch/blackfin/boards/ipe337/ipe337.c +++ b/arch/blackfin/boards/ipe337/ipe337.c @@ -4,6 +4,11 @@ #include <asm/cpu/cdefBF561.h> #include <partition.h> #include <fs.h> +#include <smc911x.h> + +struct smc911x_plat smcplat = { + .shift = 1, +}; static int ipe337_devices_init(void) { add_cfi_flash_device(DEVICE_ID_DYNAMIC, 0x20000000, 32 * 1024 * 1024, 0); @@ -17,7 +22,7 @@ static int ipe337_devices_init(void) { *pFIO0_FLAG_S = (1<<12); add_generic_device("smc911x", DEVICE_ID_DYNAMIC, NULL, 0x24000000, 4096, - IORESOURCE_MEM, NULL); + IORESOURCE_MEM, &smcplat); devfs_add_partition("nor0", 0x00000, 0x20000, DEVFS_PARTITION_FIXED, "self0"); devfs_add_partition("nor0", 0x20000, 0x20000, DEVFS_PARTITION_FIXED, "env0"); diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 749ea6a..340839d 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -36,12 +36,6 @@ config DRIVER_NET_SMC911X This option enables support for the SMSC LAN9[12]1[567] ethernet chip. -config DRIVER_NET_SMC911X_ADDRESS_SHIFT - int - depends on DRIVER_NET_SMC911X - default 1 if MACH_IPE337 - default 0 - config DRIVER_NET_SMC91111 bool "smc91111 ethernet driver" select MIIDEV diff --git a/drivers/net/smc911x.c b/drivers/net/smc911x.c index 917f994..75a332e 100644 --- a/drivers/net/smc911x.c +++ b/drivers/net/smc911x.c @@ -37,9 +37,8 @@ #include <errno.h> #include <clock.h> #include <io.h> +#include <smc911x.h> - -#define AS CONFIG_DRIVER_NET_SMC911X_ADDRESS_SHIFT #include "smc911x.h" struct smc911x_priv { @@ -47,6 +46,8 @@ struct smc911x_priv { struct mii_device miidev; void __iomem *base; + int shift; + u32 (*reg_read)(struct smc911x_priv *priv, u32 reg); void (*reg_write)(struct smc911x_priv *priv, u32 reg, u32 val); }; @@ -71,6 +72,8 @@ static const struct chip_id chip_ids[] = { #define DRIVERNAME "smc911x" +#define __smc_shift(priv, reg) ((reg) << ((priv)->shift)) + static inline u32 smc911x_reg_read(struct smc911x_priv *priv, u32 reg) { return priv->reg_read(priv, reg); @@ -87,6 +90,22 @@ static inline u32 __smc911x_reg_readl(struct smc911x_priv *priv, u32 reg) return readl(priv->base + reg); } +static inline u32 +__smc911x_reg_readw_shift(struct smc911x_priv *priv, u32 reg) +{ + return (readw(priv->base + + __smc_shift(priv, reg)) & 0xFFFF) | + ((readw(priv->base + + __smc_shift(priv, reg + 2)) & 0xFFFF) << 16); + +} + +static inline u32 +__smc911x_reg_readl_shift(struct smc911x_priv *priv, u32 reg) +{ + return readl(priv->base + __smc_shift(priv, reg)); +} + static inline void smc911x_reg_write(struct smc911x_priv *priv, u32 reg, u32 val) { @@ -106,6 +125,21 @@ static inline void __smc911x_reg_writel(struct smc911x_priv *priv, u32 reg, writel(val, priv->base + reg); } +static inline void +__smc911x_reg_writew_shift(struct smc911x_priv *priv, u32 reg, u32 val) +{ + writew(val & 0xFFFF, + priv->base + __smc_shift(priv, reg)); + writew((val >> 16) & 0xFFFF, + priv->base + __smc_shift(priv, reg + 2)); +} + +static inline void +__smc911x_reg_writel_shift(struct smc911x_priv *priv, u32 reg, u32 val) +{ + writel(val, priv->base + __smc_shift(priv, reg)); +} + static int smc911x_mac_wait_busy(struct smc911x_priv *priv) { uint64_t start = get_time_ns(); @@ -404,6 +438,7 @@ static int smc911x_probe(struct device_d *dev) struct smc911x_priv *priv; uint32_t val; int i, is_32bit; + struct smc911x_plat *pdata = dev->platform_data; priv = xzalloc(sizeof(*priv)); is_32bit = dev->resource[0].flags & IORESOURCE_MEM_TYPE_MASK; @@ -413,12 +448,25 @@ static int smc911x_probe(struct device_d *dev) is_32bit = is_32bit == IORESOURCE_MEM_32BIT; priv->base = dev_request_mem_region(dev, 0); + if (pdata && pdata->shift) + priv->shift = pdata->shift; + if (is_32bit) { - priv->reg_read = __smc911x_reg_readl; - priv->reg_write = __smc911x_reg_writel; + if (pdata->shift) { + priv->reg_read = __smc911x_reg_readl_shift; + priv->reg_write = __smc911x_reg_writel_shift; + } else { + priv->reg_read = __smc911x_reg_readl; + priv->reg_write = __smc911x_reg_writel; + } } else { - priv->reg_read = __smc911x_reg_readw; - priv->reg_write = __smc911x_reg_writew; + if (pdata->shift) { + priv->reg_read = __smc911x_reg_readw_shift; + priv->reg_write = __smc911x_reg_writew_shift; + } else { + priv->reg_read = __smc911x_reg_readw; + priv->reg_write = __smc911x_reg_writew; + } } val = smc911x_reg_read(priv, BYTE_TEST); diff --git a/drivers/net/smc911x.h b/drivers/net/smc911x.h index 68f6590..baf3598 100644 --- a/drivers/net/smc911x.h +++ b/drivers/net/smc911x.h @@ -25,9 +25,10 @@ /* Below are the register offsets and bit definitions * of the Lan911x memory space */ -#define RX_DATA_FIFO (0x00 << AS) -#define TX_DATA_FIFO (0x20 << AS) +#define RX_DATA_FIFO 0x00 + +#define TX_DATA_FIFO 0x20 #define TX_CMD_A_INT_ON_COMP 0x80000000 #define TX_CMD_A_INT_BUF_END_ALGN 0x03000000 #define TX_CMD_A_INT_4_BYTE_ALGN 0x00000000 @@ -42,7 +43,7 @@ #define TX_CMD_B_DISABLE_PADDING 0x00001000 #define TX_CMD_B_PKT_BYTE_LENGTH 0x000007FF -#define RX_STATUS_FIFO (0x40 << AS) +#define RX_STATUS_FIFO 0x40 #define RX_STS_PKT_LEN 0x3FFF0000 #define RX_STS_ES 0x00008000 #define RX_STS_BCST 0x00002000 @@ -56,8 +57,8 @@ #define RX_STS_MII_ERR 0x00000008 #define RX_STS_DRIBBLING 0x00000004 #define RX_STS_CRC_ERR 0x00000002 -#define RX_STATUS_FIFO_PEEK (0x44 << AS) -#define TX_STATUS_FIFO (0x48 << AS) +#define RX_STATUS_FIFO_PEEK 0x44 +#define TX_STATUS_FIFO 0x48 #define TX_STS_TAG 0xFFFF0000 #define TX_STS_ES 0x00008000 #define TX_STS_LOC 0x00000800 @@ -68,12 +69,12 @@ #define TX_STS_MANY_DEFER 0x00000004 #define TX_STS_UNDERRUN 0x00000002 #define TX_STS_DEFERRED 0x00000001 -#define TX_STATUS_FIFO_PEEK (0x4C << AS) -#define ID_REV (0x50 << AS) +#define TX_STATUS_FIFO_PEEK 0x4C +#define ID_REV 0x50 #define ID_REV_CHIP_ID 0xFFFF0000 /* RO */ #define ID_REV_REV_ID 0x0000FFFF /* RO */ -#define INT_CFG (0x54 << AS) +#define INT_CFG 0x54 #define INT_CFG_INT_DEAS 0xFF000000 /* R/W */ #define INT_CFG_INT_DEAS_CLR 0x00004000 #define INT_CFG_INT_DEAS_STS 0x00002000 @@ -82,7 +83,7 @@ #define INT_CFG_IRQ_POL 0x00000010 /* R/W Not Affected by SW Reset */ #define INT_CFG_IRQ_TYPE 0x00000001 /* R/W Not Affected by SW Reset */ -#define INT_STS (0x58 << AS) +#define INT_STS 0x58 #define INT_STS_SW_INT 0x80000000 /* R/WC */ #define INT_STS_TXSTOP_INT 0x02000000 /* R/WC */ #define INT_STS_RXSTOP_INT 0x01000000 /* R/WC */ @@ -111,7 +112,7 @@ #define INT_STS_GPIO2_INT 0x00000004 /* R/WC */ #define INT_STS_GPIO1_INT 0x00000002 /* R/WC */ #define INT_STS_GPIO0_INT 0x00000001 /* R/WC */ -#define INT_EN (0x5C << AS) +#define INT_EN 0x5C #define INT_EN_SW_INT_EN 0x80000000 /* R/W */ #define INT_EN_TXSTOP_INT_EN 0x02000000 /* R/W */ #define INT_EN_RXSTOP_INT_EN 0x01000000 /* R/W */ @@ -141,14 +142,14 @@ #define INT_EN_GPIO1_INT 0x00000002 /* R/W */ #define INT_EN_GPIO0_INT 0x00000001 /* R/W */ -#define BYTE_TEST (0x64 << AS) -#define FIFO_INT (0x68 << AS) +#define BYTE_TEST 0x64 +#define FIFO_INT 0x68 #define FIFO_INT_TX_AVAIL_LEVEL 0xFF000000 /* R/W */ #define FIFO_INT_TX_STS_LEVEL 0x00FF0000 /* R/W */ #define FIFO_INT_RX_AVAIL_LEVEL 0x0000FF00 /* R/W */ #define FIFO_INT_RX_STS_LEVEL 0x000000FF /* R/W */ -#define RX_CFG (0x6C << AS) +#define RX_CFG 0x6C #define RX_CFG_RX_END_ALGN 0xC0000000 /* R/W */ #define RX_CFG_RX_END_ALGN4 0x00000000 /* R/W */ #define RX_CFG_RX_END_ALGN16 0x40000000 /* R/W */ @@ -158,7 +159,7 @@ #define RX_CFG_RXDOFF 0x00001F00 /* R/W */ //#define RX_CFG_RXBAD 0x00000001 /* R/W */ -#define TX_CFG (0x70 << AS) +#define TX_CFG 0x70 //#define TX_CFG_TX_DMA_LVL 0xE0000000 /* R/W */ //#define TX_CFG_TX_DMA_CNT 0x0FFF0000 /* R/W Self Clearing */ #define TX_CFG_TXS_DUMP 0x00008000 /* Self Clearing */ @@ -167,7 +168,7 @@ #define TX_CFG_TX_ON 0x00000002 /* R/W */ #define TX_CFG_STOP_TX 0x00000001 /* Self Clearing */ -#define HW_CFG (0x74 << AS) +#define HW_CFG 0x74 #define HW_CFG_TTM 0x00200000 /* R/W */ #define HW_CFG_SF 0x00100000 /* R/W */ #define HW_CFG_TX_FIF_SZ 0x000F0000 /* R/W */ @@ -183,19 +184,19 @@ #define HW_CFG_SRST_TO 0x00000002 /* RO */ #define HW_CFG_SRST 0x00000001 /* Self Clearing */ -#define RX_DP_CTRL (0x78 << AS) +#define RX_DP_CTRL 0x78 #define RX_DP_CTRL_RX_FFWD 0x80000000 /* R/W */ #define RX_DP_CTRL_FFWD_BUSY 0x80000000 /* RO */ -#define RX_FIFO_INF (0x7C << AS) +#define RX_FIFO_INF 0x7C #define RX_FIFO_INF_RXSUSED 0x00FF0000 /* RO */ #define RX_FIFO_INF_RXDUSED 0x0000FFFF /* RO */ -#define TX_FIFO_INF (0x80 << AS) +#define TX_FIFO_INF 0x80 #define TX_FIFO_INF_TSUSED 0x00FF0000 /* RO */ #define TX_FIFO_INF_TDFREE 0x0000FFFF /* RO */ -#define PMT_CTRL (0x84 << AS) +#define PMT_CTRL 0x84 #define PMT_CTRL_PM_MODE 0x00003000 /* Self Clearing */ #define PMT_CTRL_PHY_RST 0x00000400 /* Self Clearing */ #define PMT_CTRL_WOL_EN 0x00000200 /* R/W */ @@ -211,7 +212,7 @@ #define PMT_CTRL_PME_EN 0x00000002 /* R/W Not Affected by SW Reset */ #define PMT_CTRL_READY 0x00000001 /* RO */ -#define GPIO_CFG (0x88 << AS) +#define GPIO_CFG 0x88 #define GPIO_CFG_LED3_EN 0x40000000 /* R/W */ #define GPIO_CFG_LED2_EN 0x20000000 /* R/W */ #define GPIO_CFG_LED1_EN 0x10000000 /* R/W */ @@ -231,23 +232,23 @@ #define GPIO_CFG_GPIOD1 0x00000002 /* R/W */ #define GPIO_CFG_GPIOD0 0x00000001 /* R/W */ -#define GPT_CFG (0x8C << AS) +#define GPT_CFG 0x8C #define GPT_CFG_TIMER_EN 0x20000000 /* R/W */ #define GPT_CFG_GPT_LOAD 0x0000FFFF /* R/W */ -#define GPT_CNT (0x90 << AS) +#define GPT_CNT 0x90 #define GPT_CNT_GPT_CNT 0x0000FFFF /* RO */ -#define ENDIAN (0x98 << AS) -#define FREE_RUN (0x9C << AS) -#define RX_DROP (0xA0 << AS) -#define MAC_CSR_CMD (0xA4 << AS) +#define ENDIAN 0x98 +#define FREE_RUN 0x9C +#define RX_DROP 0xA0 +#define MAC_CSR_CMD 0xA4 #define MAC_CSR_CMD_CSR_BUSY 0x80000000 /* Self Clearing */ #define MAC_CSR_CMD_R_NOT_W 0x40000000 /* R/W */ #define MAC_CSR_CMD_CSR_ADDR 0x000000FF /* R/W */ -#define MAC_CSR_DATA (0xA8 << AS) -#define AFC_CFG (0xAC << AS) +#define MAC_CSR_DATA 0xA8 +#define AFC_CFG 0xAC #define AFC_CFG_AFC_HI 0x00FF0000 /* R/W */ #define AFC_CFG_AFC_LO 0x0000FF00 /* R/W */ #define AFC_CFG_BACK_DUR 0x000000F0 /* R/W */ @@ -256,7 +257,7 @@ #define AFC_CFG_FCADD 0x00000002 /* R/W */ #define AFC_CFG_FCANY 0x00000001 /* R/W */ -#define E2P_CMD (0xB0 << AS) +#define E2P_CMD 0xB0 #define E2P_CMD_EPC_BUSY 0x80000000 /* Self Clearing */ #define E2P_CMD_EPC_CMD 0x70000000 /* R/W */ #define E2P_CMD_EPC_CMD_READ 0x00000000 /* R/W */ @@ -271,7 +272,7 @@ #define E2P_CMD_MAC_ADDR_LOADED 0x00000100 /* RO */ #define E2P_CMD_EPC_ADDR 0x000000FF /* R/W */ -#define E2P_DATA (0xB4 << AS) +#define E2P_DATA 0xB4 #define E2P_DATA_EEPROM_DATA 0x000000FF /* R/W */ /* end of LAN register offsets and bit definitions */ diff --git a/include/smc911x.h b/include/smc911x.h new file mode 100644 index 0000000..148906b --- /dev/null +++ b/include/smc911x.h @@ -0,0 +1,18 @@ +/* + * (C) Copyright 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * Under GPLv2 + */ + +#ifndef __SMC911X_PLATFORM_H_ +#define __SMC911X_PLATFORM_H_ + +/** + * @brief Platform dependent feature: + * Pass pointer to this structure as part of device_d -> platform_data + */ +struct smc911x_plat { + int shift; +}; + +#endif /* __SMC911X_PLATFORM_H_ */ -- 1.7.10.4 _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH 5/7] smc911x: improve detection handle 2012-09-01 8:52 ` [PATCH 1/7] smc911x: move register define to smc911x.h Jean-Christophe PLAGNIOL-VILLARD ` (2 preceding siblings ...) 2012-09-01 8:52 ` [PATCH 4/7] smc911x: add support to pass the shift via platform data Jean-Christophe PLAGNIOL-VILLARD @ 2012-09-01 8:52 ` Jean-Christophe PLAGNIOL-VILLARD 2012-09-01 8:52 ` [PATCH 6/7] smc911x: update chip detection Jean-Christophe PLAGNIOL-VILLARD 2012-09-01 8:52 ` [PATCH 7/7] smc911x: check if the device is ready before using it Jean-Christophe PLAGNIOL-VILLARD 5 siblings, 0 replies; 13+ messages in thread From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-09-01 8:52 UTC (permalink / raw) To: barebox detect if the bus is swapped and report a 32bit drivers is used on a 16bit bus Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> --- drivers/net/smc911x.c | 21 ++++++++++++++++++++- drivers/net/smc911x.h | 2 ++ 2 files changed, 22 insertions(+), 1 deletion(-) diff --git a/drivers/net/smc911x.c b/drivers/net/smc911x.c index 75a332e..8528527 100644 --- a/drivers/net/smc911x.c +++ b/drivers/net/smc911x.c @@ -470,9 +470,28 @@ static int smc911x_probe(struct device_d *dev) } val = smc911x_reg_read(priv, BYTE_TEST); - if(val != 0x87654321) { + if (val == 0x43218765) { + dev_dbg(dev, "BYTE_TEST looks swapped, " + "applying WORD_SWAP"); + smc911x_reg_write(priv, WORD_SWAP, 0xffffffff); + + /* 1 dummy read of BYTE_TEST is needed after a write to + * WORD_SWAP before its contents are valid */ + val = smc911x_reg_read(priv, BYTE_TEST); + + val = smc911x_reg_read(priv, BYTE_TEST); + } + + if (val != 0x87654321) { dev_err(dev, "no smc911x found on 0x%p (byte_test=0x%08x)\n", priv->base, val); + if (((val >> 16) & 0xFFFF) == (val & 0xFFFF)) { + /* + * This may mean the chip is set + * for 32 bit while the bus is reading 16 bit + */ + dev_err(dev, "top 16 bits equal to bottom 16 bits\n"); + } return -ENODEV; } diff --git a/drivers/net/smc911x.h b/drivers/net/smc911x.h index baf3598..d409247 100644 --- a/drivers/net/smc911x.h +++ b/drivers/net/smc911x.h @@ -26,6 +26,8 @@ * of the Lan911x memory space */ +#define WORD_SWAP 0x98 + #define RX_DATA_FIFO 0x00 #define TX_DATA_FIFO 0x20 -- 1.7.10.4 _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH 6/7] smc911x: update chip detection 2012-09-01 8:52 ` [PATCH 1/7] smc911x: move register define to smc911x.h Jean-Christophe PLAGNIOL-VILLARD ` (3 preceding siblings ...) 2012-09-01 8:52 ` [PATCH 5/7] smc911x: improve detection handle Jean-Christophe PLAGNIOL-VILLARD @ 2012-09-01 8:52 ` Jean-Christophe PLAGNIOL-VILLARD 2012-09-01 8:52 ` [PATCH 7/7] smc911x: check if the device is ready before using it Jean-Christophe PLAGNIOL-VILLARD 5 siblings, 0 replies; 13+ messages in thread From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-09-01 8:52 UTC (permalink / raw) To: barebox Use linux kernel chip detection from 3.5 Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> --- drivers/net/smc911x.c | 60 ++++++++++++++++++++++++++++--------------------- drivers/net/smc911x.h | 13 ----------- 2 files changed, 34 insertions(+), 39 deletions(-) diff --git a/drivers/net/smc911x.c b/drivers/net/smc911x.c index 8528527..7639a92 100644 --- a/drivers/net/smc911x.c +++ b/drivers/net/smc911x.c @@ -47,29 +47,12 @@ struct smc911x_priv { void __iomem *base; int shift; + int generation; u32 (*reg_read)(struct smc911x_priv *priv, u32 reg); void (*reg_write)(struct smc911x_priv *priv, u32 reg, u32 val); }; -struct chip_id { - u16 id; - char *name; -}; - -static const struct chip_id chip_ids[] = { - { CHIP_9115, "LAN9115" }, - { CHIP_9116, "LAN9116" }, - { CHIP_9117, "LAN9117" }, - { CHIP_9118, "LAN9118" }, - { CHIP_9215, "LAN9215" }, - { CHIP_9216, "LAN9216" }, - { CHIP_9217, "LAN9217" }, - { CHIP_9218, "LAN9218" }, - { CHIP_9221, "LAN9221" }, - { 0, NULL }, -}; - #define DRIVERNAME "smc911x" #define __smc_shift(priv, reg) ((reg) << ((priv)->shift)) @@ -437,7 +420,7 @@ static int smc911x_probe(struct device_d *dev) struct eth_device *edev; struct smc911x_priv *priv; uint32_t val; - int i, is_32bit; + int is_32bit; struct smc911x_plat *pdata = dev->platform_data; priv = xzalloc(sizeof(*priv)); @@ -495,16 +478,41 @@ static int smc911x_probe(struct device_d *dev) return -ENODEV; } - val = smc911x_reg_read(priv, ID_REV) >> 16; - for(i = 0; chip_ids[i].id != 0; i++) { - if (chip_ids[i].id == val) break; - } - if (!chip_ids[i].id) { - dev_err(dev, "Unknown chip ID %04x\n", val); + val = smc911x_reg_read(priv, ID_REV); + switch (val & 0xFFFF0000) { + case 0x01180000: + case 0x01170000: + case 0x01160000: + case 0x01150000: + case 0x218A0000: + /* LAN911[5678] family */ + priv->generation = val & 0x0000FFFF; + break; + + case 0x118A0000: + case 0x117A0000: + case 0x116A0000: + case 0x115A0000: + /* LAN921[5678] family */ + priv->generation = 3; + break; + + case 0x92100000: + case 0x92110000: + case 0x92200000: + case 0x92210000: + /* LAN9210/LAN9211/LAN9220/LAN9221 */ + priv->generation = 4; + break; + + default: + dev_err(dev, "LAN911x not identified, idrev: 0x%08X\n", + val); return -ENODEV; } - dev_info(dev, "detected %s controller\n", chip_ids[i].name); + dev_info(dev, "LAN911x identified, idrev: 0x%08X, generation: %d\n", + val, priv->generation); edev = &priv->edev; edev->priv = priv; diff --git a/drivers/net/smc911x.h b/drivers/net/smc911x.h index d409247..572c1f8 100644 --- a/drivers/net/smc911x.h +++ b/drivers/net/smc911x.h @@ -340,16 +340,3 @@ #define WUCSR_MPR 0x00000020 #define WUCSR_WAKE_EN 0x00000004 #define WUCSR_MPEN 0x00000002 - -/* Chip ID values */ -#define CHIP_9115 0x115 -#define CHIP_9116 0x116 -#define CHIP_9117 0x117 -#define CHIP_9118 0x118 -#define CHIP_9215 0x115a -#define CHIP_9216 0x116a -#define CHIP_9217 0x117a -#define CHIP_9218 0x118a -#define CHIP_9221 0x9221 - - -- 1.7.10.4 _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH 7/7] smc911x: check if the device is ready before using it 2012-09-01 8:52 ` [PATCH 1/7] smc911x: move register define to smc911x.h Jean-Christophe PLAGNIOL-VILLARD ` (4 preceding siblings ...) 2012-09-01 8:52 ` [PATCH 6/7] smc911x: update chip detection Jean-Christophe PLAGNIOL-VILLARD @ 2012-09-01 8:52 ` Jean-Christophe PLAGNIOL-VILLARD 5 siblings, 0 replies; 13+ messages in thread From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-09-01 8:52 UTC (permalink / raw) To: barebox poll the READY bit in PMT_CTRL. Any other access to the device is forbidden while this bit isn't set. Try for 100ms Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> --- drivers/net/smc911x.c | 12 +++++++++++- 1 file changed, 11 insertions(+), 1 deletion(-) diff --git a/drivers/net/smc911x.c b/drivers/net/smc911x.c index 7639a92..3ccb0ef 100644 --- a/drivers/net/smc911x.c +++ b/drivers/net/smc911x.c @@ -420,7 +420,7 @@ static int smc911x_probe(struct device_d *dev) struct eth_device *edev; struct smc911x_priv *priv; uint32_t val; - int is_32bit; + int is_32bit, ret; struct smc911x_plat *pdata = dev->platform_data; priv = xzalloc(sizeof(*priv)); @@ -452,6 +452,16 @@ static int smc911x_probe(struct device_d *dev) } } + /* + * poll the READY bit in PMT_CTRL. Any other access to the device is + * forbidden while this bit isn't set. Try for 100ms + */ + ret = wait_on_timeout(100 * MSECOND, smc911x_reg_read(priv, PMT_CTRL) & PMT_CTRL_READY); + if (!ret) { + dev_err(dev, "Device not READY in 100ms aborting\n"); + return -ENODEV; + } + val = smc911x_reg_read(priv, BYTE_TEST); if (val == 0x43218765) { dev_dbg(dev, "BYTE_TEST looks swapped, " -- 1.7.10.4 _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH 0/7 v3] smsc911x: runtime configuration improvement 2012-09-01 8:47 [PATCH 0/7 v3] smsc911x: runtime configuration improvement Jean-Christophe PLAGNIOL-VILLARD 2012-09-01 8:52 ` [PATCH 1/7] smc911x: move register define to smc911x.h Jean-Christophe PLAGNIOL-VILLARD @ 2012-09-03 7:49 ` Sascha Hauer 1 sibling, 0 replies; 13+ messages in thread From: Sascha Hauer @ 2012-09-03 7:49 UTC (permalink / raw) To: Jean-Christophe PLAGNIOL-VILLARD; +Cc: barebox On Sat, Sep 01, 2012 at 10:47:28AM +0200, Jean-Christophe PLAGNIOL-VILLARD wrote: > Hi, > > v3: > update commnets > > v2: > update 16/32bit callback > > please pull > The following changes since commit 3f96b4938c4046590be8a38fb114148c4bf1ca8e: > > Merge tag 'bootm_fix' of git://git.jcrosoft.org/barebox (2012-08-13 20:37:53 +0200) > > are available in the git repository at:# Applied, thanks Sascha -- Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH 0/7 2] smsc911x: runtime configuration improvement
@ 2012-08-29 4:27 Jean-Christophe PLAGNIOL-VILLARD
2012-08-29 5:06 ` [PATCH 1/7] smc911x: move register define to smc911x.h Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 1 reply; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-08-29 4:27 UTC (permalink / raw)
To: barebox
Hi,
v2:
update 16/32bit callback
please pull
The following changes since commit 3f96b4938c4046590be8a38fb114148c4bf1ca8e:
Merge tag 'bootm_fix' of git://git.jcrosoft.org/barebox (2012-08-13 20:37:53 +0200)
are available in the git repository at:
git://git.jcrosoft.org/barebox.git tags/smc911x_improve
for you to fetch changes up to 58957dad540642eecbd79ab581e120e0e1ccbae1:
smm911x: check if the device is ready before using it (2012-08-26 06:19:10 +0800)
----------------------------------------------------------------
smsc911x: runtime configuration improvement
This patch series allow to detect and configure the drivers at the runtime
- Check if the device is ready before using it
- Update chip detection (take from the kernel 3.5)
- improve detection handle to detect bus configuration and swap
- add support to pass the shift via platform data
- add 16bit bus width support
- introduce read/write ops
- move register define to smc911x.h
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
----------------------------------------------------------------
Jean-Christophe PLAGNIOL-VILLARD (7):
smc911x: move register define to smc911x.h
smc911x: introduce read/write ops
smc911x: add 16bit bus width support
smc911x: add support to pass the shift via platform data
smc911x: improve detection handle
smc911x: update chip detection
smm911x: check if the device is ready before using it
arch/blackfin/boards/ipe337/ipe337.c | 7 +-
drivers/net/Kconfig | 6 --
drivers/net/smc911x.c | 590 ++++++++++++++++++++++++++++++++++++++++++++--------------------------------------------------------------------------------------
drivers/net/smc911x.h | 342 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
include/smc911x.h | 18 ++++
5 files changed, 566 insertions(+), 397 deletions(-)
create mode 100644 drivers/net/smc911x.h
create mode 100644 include/smc911x.h
Best Regards,
J.
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* [PATCH 1/7] smc911x: move register define to smc911x.h 2012-08-29 4:27 [PATCH 0/7 2] " Jean-Christophe PLAGNIOL-VILLARD @ 2012-08-29 5:06 ` Jean-Christophe PLAGNIOL-VILLARD 0 siblings, 0 replies; 13+ messages in thread From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-08-29 5:06 UTC (permalink / raw) To: barebox this make the driver more readable Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> --- drivers/net/smc911x.c | 329 +-------------------------- drivers/net/{smc911x.c => smc911x.h} | 406 ---------------------------------- 2 files changed, 2 insertions(+), 733 deletions(-) copy drivers/net/{smc911x.c => smc911x.h} (60%) diff --git a/drivers/net/smc911x.c b/drivers/net/smc911x.c index 7dddbbc..9c488c7 100644 --- a/drivers/net/smc911x.c +++ b/drivers/net/smc911x.c @@ -38,334 +38,9 @@ #include <clock.h> #include <io.h> -#define AS CONFIG_DRIVER_NET_SMC911X_ADDRESS_SHIFT -/* Below are the register offsets and bit definitions - * of the Lan911x memory space - */ -#define RX_DATA_FIFO (0x00 << AS) - -#define TX_DATA_FIFO (0x20 << AS) -#define TX_CMD_A_INT_ON_COMP 0x80000000 -#define TX_CMD_A_INT_BUF_END_ALGN 0x03000000 -#define TX_CMD_A_INT_4_BYTE_ALGN 0x00000000 -#define TX_CMD_A_INT_16_BYTE_ALGN 0x01000000 -#define TX_CMD_A_INT_32_BYTE_ALGN 0x02000000 -#define TX_CMD_A_INT_DATA_OFFSET 0x001F0000 -#define TX_CMD_A_INT_FIRST_SEG 0x00002000 -#define TX_CMD_A_INT_LAST_SEG 0x00001000 -#define TX_CMD_A_BUF_SIZE 0x000007FF -#define TX_CMD_B_PKT_TAG 0xFFFF0000 -#define TX_CMD_B_ADD_CRC_DISABLE 0x00002000 -#define TX_CMD_B_DISABLE_PADDING 0x00001000 -#define TX_CMD_B_PKT_BYTE_LENGTH 0x000007FF - -#define RX_STATUS_FIFO (0x40 << AS) -#define RX_STS_PKT_LEN 0x3FFF0000 -#define RX_STS_ES 0x00008000 -#define RX_STS_BCST 0x00002000 -#define RX_STS_LEN_ERR 0x00001000 -#define RX_STS_RUNT_ERR 0x00000800 -#define RX_STS_MCAST 0x00000400 -#define RX_STS_TOO_LONG 0x00000080 -#define RX_STS_COLL 0x00000040 -#define RX_STS_ETH_TYPE 0x00000020 -#define RX_STS_WDOG_TMT 0x00000010 -#define RX_STS_MII_ERR 0x00000008 -#define RX_STS_DRIBBLING 0x00000004 -#define RX_STS_CRC_ERR 0x00000002 -#define RX_STATUS_FIFO_PEEK (0x44 << AS) -#define TX_STATUS_FIFO (0x48 << AS) -#define TX_STS_TAG 0xFFFF0000 -#define TX_STS_ES 0x00008000 -#define TX_STS_LOC 0x00000800 -#define TX_STS_NO_CARR 0x00000400 -#define TX_STS_LATE_COLL 0x00000200 -#define TX_STS_MANY_COLL 0x00000100 -#define TX_STS_COLL_CNT 0x00000078 -#define TX_STS_MANY_DEFER 0x00000004 -#define TX_STS_UNDERRUN 0x00000002 -#define TX_STS_DEFERRED 0x00000001 -#define TX_STATUS_FIFO_PEEK (0x4C << AS) -#define ID_REV (0x50 << AS) -#define ID_REV_CHIP_ID 0xFFFF0000 /* RO */ -#define ID_REV_REV_ID 0x0000FFFF /* RO */ - -#define INT_CFG (0x54 << AS) -#define INT_CFG_INT_DEAS 0xFF000000 /* R/W */ -#define INT_CFG_INT_DEAS_CLR 0x00004000 -#define INT_CFG_INT_DEAS_STS 0x00002000 -#define INT_CFG_IRQ_INT 0x00001000 /* RO */ -#define INT_CFG_IRQ_EN 0x00000100 /* R/W */ -#define INT_CFG_IRQ_POL 0x00000010 /* R/W Not Affected by SW Reset */ -#define INT_CFG_IRQ_TYPE 0x00000001 /* R/W Not Affected by SW Reset */ - -#define INT_STS (0x58 << AS) -#define INT_STS_SW_INT 0x80000000 /* R/WC */ -#define INT_STS_TXSTOP_INT 0x02000000 /* R/WC */ -#define INT_STS_RXSTOP_INT 0x01000000 /* R/WC */ -#define INT_STS_RXDFH_INT 0x00800000 /* R/WC */ -#define INT_STS_RXDF_INT 0x00400000 /* R/WC */ -#define INT_STS_TX_IOC 0x00200000 /* R/WC */ -#define INT_STS_RXD_INT 0x00100000 /* R/WC */ -#define INT_STS_GPT_INT 0x00080000 /* R/WC */ -#define INT_STS_PHY_INT 0x00040000 /* RO */ -#define INT_STS_PME_INT 0x00020000 /* R/WC */ -#define INT_STS_TXSO 0x00010000 /* R/WC */ -#define INT_STS_RWT 0x00008000 /* R/WC */ -#define INT_STS_RXE 0x00004000 /* R/WC */ -#define INT_STS_TXE 0x00002000 /* R/WC */ -//#define INT_STS_ERX 0x00001000 /* R/WC */ -#define INT_STS_TDFU 0x00000800 /* R/WC */ -#define INT_STS_TDFO 0x00000400 /* R/WC */ -#define INT_STS_TDFA 0x00000200 /* R/WC */ -#define INT_STS_TSFF 0x00000100 /* R/WC */ -#define INT_STS_TSFL 0x00000080 /* R/WC */ -//#define INT_STS_RXDF 0x00000040 /* R/WC */ -#define INT_STS_RDFO 0x00000040 /* R/WC */ -#define INT_STS_RDFL 0x00000020 /* R/WC */ -#define INT_STS_RSFF 0x00000010 /* R/WC */ -#define INT_STS_RSFL 0x00000008 /* R/WC */ -#define INT_STS_GPIO2_INT 0x00000004 /* R/WC */ -#define INT_STS_GPIO1_INT 0x00000002 /* R/WC */ -#define INT_STS_GPIO0_INT 0x00000001 /* R/WC */ -#define INT_EN (0x5C << AS) -#define INT_EN_SW_INT_EN 0x80000000 /* R/W */ -#define INT_EN_TXSTOP_INT_EN 0x02000000 /* R/W */ -#define INT_EN_RXSTOP_INT_EN 0x01000000 /* R/W */ -#define INT_EN_RXDFH_INT_EN 0x00800000 /* R/W */ -//#define INT_EN_RXDF_INT_EN 0x00400000 /* R/W */ -#define INT_EN_TIOC_INT_EN 0x00200000 /* R/W */ -#define INT_EN_RXD_INT_EN 0x00100000 /* R/W */ -#define INT_EN_GPT_INT_EN 0x00080000 /* R/W */ -#define INT_EN_PHY_INT_EN 0x00040000 /* R/W */ -#define INT_EN_PME_INT_EN 0x00020000 /* R/W */ -#define INT_EN_TXSO_EN 0x00010000 /* R/W */ -#define INT_EN_RWT_EN 0x00008000 /* R/W */ -#define INT_EN_RXE_EN 0x00004000 /* R/W */ -#define INT_EN_TXE_EN 0x00002000 /* R/W */ -//#define INT_EN_ERX_EN 0x00001000 /* R/W */ -#define INT_EN_TDFU_EN 0x00000800 /* R/W */ -#define INT_EN_TDFO_EN 0x00000400 /* R/W */ -#define INT_EN_TDFA_EN 0x00000200 /* R/W */ -#define INT_EN_TSFF_EN 0x00000100 /* R/W */ -#define INT_EN_TSFL_EN 0x00000080 /* R/W */ -//#define INT_EN_RXDF_EN 0x00000040 /* R/W */ -#define INT_EN_RDFO_EN 0x00000040 /* R/W */ -#define INT_EN_RDFL_EN 0x00000020 /* R/W */ -#define INT_EN_RSFF_EN 0x00000010 /* R/W */ -#define INT_EN_RSFL_EN 0x00000008 /* R/W */ -#define INT_EN_GPIO2_INT 0x00000004 /* R/W */ -#define INT_EN_GPIO1_INT 0x00000002 /* R/W */ -#define INT_EN_GPIO0_INT 0x00000001 /* R/W */ - -#define BYTE_TEST (0x64 << AS) -#define FIFO_INT (0x68 << AS) -#define FIFO_INT_TX_AVAIL_LEVEL 0xFF000000 /* R/W */ -#define FIFO_INT_TX_STS_LEVEL 0x00FF0000 /* R/W */ -#define FIFO_INT_RX_AVAIL_LEVEL 0x0000FF00 /* R/W */ -#define FIFO_INT_RX_STS_LEVEL 0x000000FF /* R/W */ - -#define RX_CFG (0x6C << AS) -#define RX_CFG_RX_END_ALGN 0xC0000000 /* R/W */ -#define RX_CFG_RX_END_ALGN4 0x00000000 /* R/W */ -#define RX_CFG_RX_END_ALGN16 0x40000000 /* R/W */ -#define RX_CFG_RX_END_ALGN32 0x80000000 /* R/W */ -#define RX_CFG_RX_DMA_CNT 0x0FFF0000 /* R/W */ -#define RX_CFG_RX_DUMP 0x00008000 /* R/W */ -#define RX_CFG_RXDOFF 0x00001F00 /* R/W */ -//#define RX_CFG_RXBAD 0x00000001 /* R/W */ - -#define TX_CFG (0x70 << AS) -//#define TX_CFG_TX_DMA_LVL 0xE0000000 /* R/W */ -//#define TX_CFG_TX_DMA_CNT 0x0FFF0000 /* R/W Self Clearing */ -#define TX_CFG_TXS_DUMP 0x00008000 /* Self Clearing */ -#define TX_CFG_TXD_DUMP 0x00004000 /* Self Clearing */ -#define TX_CFG_TXSAO 0x00000004 /* R/W */ -#define TX_CFG_TX_ON 0x00000002 /* R/W */ -#define TX_CFG_STOP_TX 0x00000001 /* Self Clearing */ - -#define HW_CFG (0x74 << AS) -#define HW_CFG_TTM 0x00200000 /* R/W */ -#define HW_CFG_SF 0x00100000 /* R/W */ -#define HW_CFG_TX_FIF_SZ 0x000F0000 /* R/W */ -#define HW_CFG_TR 0x00003000 /* R/W */ -#define HW_CFG_PHY_CLK_SEL 0x00000060 /* R/W */ -#define HW_CFG_PHY_CLK_SEL_INT_PHY 0x00000000 /* R/W */ -#define HW_CFG_PHY_CLK_SEL_EXT_PHY 0x00000020 /* R/W */ -#define HW_CFG_PHY_CLK_SEL_CLK_DIS 0x00000040 /* R/W */ -#define HW_CFG_SMI_SEL 0x00000010 /* R/W */ -#define HW_CFG_EXT_PHY_DET 0x00000008 /* RO */ -#define HW_CFG_EXT_PHY_EN 0x00000004 /* R/W */ -#define HW_CFG_32_16_BIT_MODE 0x00000004 /* RO */ -#define HW_CFG_SRST_TO 0x00000002 /* RO */ -#define HW_CFG_SRST 0x00000001 /* Self Clearing */ - -#define RX_DP_CTRL (0x78 << AS) -#define RX_DP_CTRL_RX_FFWD 0x80000000 /* R/W */ -#define RX_DP_CTRL_FFWD_BUSY 0x80000000 /* RO */ - -#define RX_FIFO_INF (0x7C << AS) -#define RX_FIFO_INF_RXSUSED 0x00FF0000 /* RO */ -#define RX_FIFO_INF_RXDUSED 0x0000FFFF /* RO */ - -#define TX_FIFO_INF (0x80 << AS) -#define TX_FIFO_INF_TSUSED 0x00FF0000 /* RO */ -#define TX_FIFO_INF_TDFREE 0x0000FFFF /* RO */ - -#define PMT_CTRL (0x84 << AS) -#define PMT_CTRL_PM_MODE 0x00003000 /* Self Clearing */ -#define PMT_CTRL_PHY_RST 0x00000400 /* Self Clearing */ -#define PMT_CTRL_WOL_EN 0x00000200 /* R/W */ -#define PMT_CTRL_ED_EN 0x00000100 /* R/W */ -#define PMT_CTRL_PME_TYPE 0x00000040 /* R/W Not Affected by SW Reset */ -#define PMT_CTRL_WUPS 0x00000030 /* R/WC */ -#define PMT_CTRL_WUPS_NOWAKE 0x00000000 /* R/WC */ -#define PMT_CTRL_WUPS_ED 0x00000010 /* R/WC */ -#define PMT_CTRL_WUPS_WOL 0x00000020 /* R/WC */ -#define PMT_CTRL_WUPS_MULTI 0x00000030 /* R/WC */ -#define PMT_CTRL_PME_IND 0x00000008 /* R/W */ -#define PMT_CTRL_PME_POL 0x00000004 /* R/W */ -#define PMT_CTRL_PME_EN 0x00000002 /* R/W Not Affected by SW Reset */ -#define PMT_CTRL_READY 0x00000001 /* RO */ - -#define GPIO_CFG (0x88 << AS) -#define GPIO_CFG_LED3_EN 0x40000000 /* R/W */ -#define GPIO_CFG_LED2_EN 0x20000000 /* R/W */ -#define GPIO_CFG_LED1_EN 0x10000000 /* R/W */ -#define GPIO_CFG_GPIO2_INT_POL 0x04000000 /* R/W */ -#define GPIO_CFG_GPIO1_INT_POL 0x02000000 /* R/W */ -#define GPIO_CFG_GPIO0_INT_POL 0x01000000 /* R/W */ -#define GPIO_CFG_EEPR_EN 0x00700000 /* R/W */ -#define GPIO_CFG_GPIOBUF2 0x00040000 /* R/W */ -#define GPIO_CFG_GPIOBUF1 0x00020000 /* R/W */ -#define GPIO_CFG_GPIOBUF0 0x00010000 /* R/W */ -#define GPIO_CFG_GPIODIR2 0x00000400 /* R/W */ -#define GPIO_CFG_GPIODIR1 0x00000200 /* R/W */ -#define GPIO_CFG_GPIODIR0 0x00000100 /* R/W */ -#define GPIO_CFG_GPIOD4 0x00000010 /* R/W */ -#define GPIO_CFG_GPIOD3 0x00000008 /* R/W */ -#define GPIO_CFG_GPIOD2 0x00000004 /* R/W */ -#define GPIO_CFG_GPIOD1 0x00000002 /* R/W */ -#define GPIO_CFG_GPIOD0 0x00000001 /* R/W */ - -#define GPT_CFG (0x8C << AS) -#define GPT_CFG_TIMER_EN 0x20000000 /* R/W */ -#define GPT_CFG_GPT_LOAD 0x0000FFFF /* R/W */ - -#define GPT_CNT (0x90 << AS) -#define GPT_CNT_GPT_CNT 0x0000FFFF /* RO */ - -#define ENDIAN (0x98 << AS) -#define FREE_RUN (0x9C << AS) -#define RX_DROP (0xA0 << AS) -#define MAC_CSR_CMD (0xA4 << AS) -#define MAC_CSR_CMD_CSR_BUSY 0x80000000 /* Self Clearing */ -#define MAC_CSR_CMD_R_NOT_W 0x40000000 /* R/W */ -#define MAC_CSR_CMD_CSR_ADDR 0x000000FF /* R/W */ - -#define MAC_CSR_DATA (0xA8 << AS) -#define AFC_CFG (0xAC << AS) -#define AFC_CFG_AFC_HI 0x00FF0000 /* R/W */ -#define AFC_CFG_AFC_LO 0x0000FF00 /* R/W */ -#define AFC_CFG_BACK_DUR 0x000000F0 /* R/W */ -#define AFC_CFG_FCMULT 0x00000008 /* R/W */ -#define AFC_CFG_FCBRD 0x00000004 /* R/W */ -#define AFC_CFG_FCADD 0x00000002 /* R/W */ -#define AFC_CFG_FCANY 0x00000001 /* R/W */ - -#define E2P_CMD (0xB0 << AS) -#define E2P_CMD_EPC_BUSY 0x80000000 /* Self Clearing */ -#define E2P_CMD_EPC_CMD 0x70000000 /* R/W */ -#define E2P_CMD_EPC_CMD_READ 0x00000000 /* R/W */ -#define E2P_CMD_EPC_CMD_EWDS 0x10000000 /* R/W */ -#define E2P_CMD_EPC_CMD_EWEN 0x20000000 /* R/W */ -#define E2P_CMD_EPC_CMD_WRITE 0x30000000 /* R/W */ -#define E2P_CMD_EPC_CMD_WRAL 0x40000000 /* R/W */ -#define E2P_CMD_EPC_CMD_ERASE 0x50000000 /* R/W */ -#define E2P_CMD_EPC_CMD_ERAL 0x60000000 /* R/W */ -#define E2P_CMD_EPC_CMD_RELOAD 0x70000000 /* R/W */ -#define E2P_CMD_EPC_TIMEOUT 0x00000200 /* RO */ -#define E2P_CMD_MAC_ADDR_LOADED 0x00000100 /* RO */ -#define E2P_CMD_EPC_ADDR 0x000000FF /* R/W */ - -#define E2P_DATA (0xB4 << AS) -#define E2P_DATA_EEPROM_DATA 0x000000FF /* R/W */ -/* end of LAN register offsets and bit definitions */ - -/* MAC Control and Status registers */ -#define MAC_CR 0x01 /* R/W */ - -/* MAC_CR - MAC Control Register */ -#define MAC_CR_RXALL 0x80000000 -// TODO: delete this bit? It is not described in the data sheet. -#define MAC_CR_HBDIS 0x10000000 -#define MAC_CR_RCVOWN 0x00800000 -#define MAC_CR_LOOPBK 0x00200000 -#define MAC_CR_FDPX 0x00100000 -#define MAC_CR_MCPAS 0x00080000 -#define MAC_CR_PRMS 0x00040000 -#define MAC_CR_INVFILT 0x00020000 -#define MAC_CR_PASSBAD 0x00010000 -#define MAC_CR_HFILT 0x00008000 -#define MAC_CR_HPFILT 0x00002000 -#define MAC_CR_LCOLL 0x00001000 -#define MAC_CR_BCAST 0x00000800 -#define MAC_CR_DISRTY 0x00000400 -#define MAC_CR_PADSTR 0x00000100 -#define MAC_CR_BOLMT_MASK 0x000000C0 -#define MAC_CR_DFCHK 0x00000020 -#define MAC_CR_TXEN 0x00000008 -#define MAC_CR_RXEN 0x00000004 - -#define ADDRH 0x02 /* R/W mask 0x0000FFFFUL */ -#define ADDRL 0x03 /* R/W mask 0xFFFFFFFFUL */ -#define HASHH 0x04 /* R/W */ -#define HASHL 0x05 /* R/W */ - -#define MII_ACC 0x06 /* R/W */ -#define MII_ACC_PHY_ADDR 0x0000F800 -#define MII_ACC_MIIRINDA 0x000007C0 -#define MII_ACC_MII_WRITE 0x00000002 -#define MII_ACC_MII_BUSY 0x00000001 - -#define MII_DATA 0x07 /* R/W mask 0x0000FFFFUL */ - -#ifdef FLOW -#undef FLOW /* clashed with include/asm/cpu/defBF561.h:1654 */ -#endif - -#define FLOW 0x08 /* R/W */ -#define FLOW_FCPT 0xFFFF0000 -#define FLOW_FCPASS 0x00000004 -#define FLOW_FCEN 0x00000002 -#define FLOW_FCBSY 0x00000001 - -#define VLAN1 0x09 /* R/W mask 0x0000FFFFUL */ -#define VLAN1_VTI1 0x0000ffff - -#define VLAN2 0x0A /* R/W mask 0x0000FFFFUL */ -#define VLAN2_VTI2 0x0000ffff - -#define WUFF 0x0B /* WO */ - -#define WUCSR 0x0C /* R/W */ -#define WUCSR_GUE 0x00000200 -#define WUCSR_WUFR 0x00000040 -#define WUCSR_MPR 0x00000020 -#define WUCSR_WAKE_EN 0x00000004 -#define WUCSR_MPEN 0x00000002 - -/* Chip ID values */ -#define CHIP_9115 0x115 -#define CHIP_9116 0x116 -#define CHIP_9117 0x117 -#define CHIP_9118 0x118 -#define CHIP_9215 0x115a -#define CHIP_9216 0x116a -#define CHIP_9217 0x117a -#define CHIP_9218 0x118a -#define CHIP_9221 0x9221 +#define AS CONFIG_DRIVER_NET_SMC911X_ADDRESS_SHIFT +#include "smc911x.h" struct smc911x_priv { struct eth_device edev; diff --git a/drivers/net/smc911x.c b/drivers/net/smc911x.h similarity index 60% copy from drivers/net/smc911x.c copy to drivers/net/smc911x.h index 7dddbbc..68f6590 100644 --- a/drivers/net/smc911x.c +++ b/drivers/net/smc911x.h @@ -22,24 +22,6 @@ * MA 02111-1307 USA */ -#ifdef CONFIG_ENABLE_DEVICE_NOISE -# define DEBUG -#endif - -#include <common.h> - -#include <command.h> -#include <net.h> -#include <miidev.h> -#include <malloc.h> -#include <init.h> -#include <xfuncs.h> -#include <errno.h> -#include <clock.h> -#include <io.h> - -#define AS CONFIG_DRIVER_NET_SMC911X_ADDRESS_SHIFT - /* Below are the register offsets and bit definitions * of the Lan911x memory space */ @@ -367,392 +349,4 @@ #define CHIP_9218 0x118a #define CHIP_9221 0x9221 -struct smc911x_priv { - struct eth_device edev; - struct mii_device miidev; - void __iomem *base; -}; - -struct chip_id { - u16 id; - char *name; -}; - -static const struct chip_id chip_ids[] = { - { CHIP_9115, "LAN9115" }, - { CHIP_9116, "LAN9116" }, - { CHIP_9117, "LAN9117" }, - { CHIP_9118, "LAN9118" }, - { CHIP_9215, "LAN9215" }, - { CHIP_9216, "LAN9216" }, - { CHIP_9217, "LAN9217" }, - { CHIP_9218, "LAN9218" }, - { CHIP_9221, "LAN9221" }, - { 0, NULL }, -}; - -#define DRIVERNAME "smc911x" - -static int smc911x_mac_wait_busy(struct smc911x_priv *priv) -{ - uint64_t start = get_time_ns(); - - while (!is_timeout(start, MSECOND)) { - if (!(readl(priv->base + MAC_CSR_CMD) & MAC_CSR_CMD_CSR_BUSY)) - return 0; - } - - printf("%s: mac timeout\n", __FUNCTION__); - return -1; -} - -static u32 smc911x_get_mac_csr(struct eth_device *edev, u8 reg) -{ - struct smc911x_priv *priv = edev->priv; - ulong val; - - smc911x_mac_wait_busy(priv); - - writel(MAC_CSR_CMD_CSR_BUSY | MAC_CSR_CMD_R_NOT_W | reg, - priv->base + MAC_CSR_CMD); - - smc911x_mac_wait_busy(priv); - - val = readl(priv->base + MAC_CSR_DATA); - - return val; -} - -static void smc911x_set_mac_csr(struct eth_device *edev, u8 reg, u32 data) -{ - struct smc911x_priv *priv = edev->priv; - - smc911x_mac_wait_busy(priv); - - writel(data, priv->base + MAC_CSR_DATA); - writel(MAC_CSR_CMD_CSR_BUSY | reg, priv->base + MAC_CSR_CMD); - - smc911x_mac_wait_busy(priv); -} - -static int smc911x_get_ethaddr(struct eth_device *edev, unsigned char *m) -{ - unsigned long addrh, addrl; - - addrh = smc911x_get_mac_csr(edev, ADDRH); - addrl = smc911x_get_mac_csr(edev, ADDRL); - - m[0] = (addrl ) & 0xff; - m[1] = (addrl >> 8 ) & 0xff; - m[2] = (addrl >> 16 ) & 0xff; - m[3] = (addrl >> 24 ) & 0xff; - m[4] = (addrh ) & 0xff; - m[5] = (addrh >> 8 ) & 0xff; - - /* we get 0xff when there is no eeprom connected */ - if ((m[0] & m[1] & m[2] & m[3] & m[4] & m[5]) == 0xff) - return -1; - - return 0; -} - -static int smc911x_set_ethaddr(struct eth_device *edev, unsigned char *m) -{ - unsigned long addrh, addrl; - - addrl = m[0] | m[1] << 8 | m[2] << 16 | m[3] << 24; - addrh = m[4] | m[5] << 8; - smc911x_set_mac_csr(edev, ADDRH, addrh); - smc911x_set_mac_csr(edev, ADDRL, addrl); - - return 0; -} - -static int smc911x_phy_read(struct mii_device *mdev, int phy_addr, int reg) -{ - struct eth_device *edev = mdev->edev; - - while (smc911x_get_mac_csr(edev, MII_ACC) & MII_ACC_MII_BUSY); - - smc911x_set_mac_csr(edev, MII_ACC, phy_addr << 11 | reg << 6 | - MII_ACC_MII_BUSY); - - while (smc911x_get_mac_csr(edev, MII_ACC) & MII_ACC_MII_BUSY); - - return smc911x_get_mac_csr(edev, MII_DATA); -} - -static int smc911x_phy_write(struct mii_device *mdev, int phy_addr, - int reg, int val) -{ - struct eth_device *edev = mdev->edev; - - while (smc911x_get_mac_csr(edev, MII_ACC) & MII_ACC_MII_BUSY); - - smc911x_set_mac_csr(edev, MII_DATA, val); - smc911x_set_mac_csr(edev, MII_ACC, - phy_addr << 11 | reg << 6 | MII_ACC_MII_BUSY | - MII_ACC_MII_WRITE); - - while (smc911x_get_mac_csr(edev, MII_ACC) & MII_ACC_MII_BUSY); - - return 0; -} - -static int smc911x_phy_reset(struct eth_device *edev) -{ - struct smc911x_priv *priv = edev->priv; - u32 reg; - - reg = readl(priv->base + PMT_CTRL); - reg &= 0xfcf; - reg |= PMT_CTRL_PHY_RST; - writel(reg, priv->base + PMT_CTRL); - - mdelay(100); - - return 0; -} - -static void smc911x_reset(struct eth_device *edev) -{ - struct smc911x_priv *priv = edev->priv; - uint64_t start; - - /* Take out of PM setting first */ - if (readl(priv->base + PMT_CTRL) & PMT_CTRL_READY) { - /* Write to the bytetest will take out of powerdown */ - writel(0, priv->base + BYTE_TEST); - - start = get_time_ns(); - while(1) { - if ((readl(priv->base + PMT_CTRL) & PMT_CTRL_READY)) - break; - if (is_timeout(start, 100 * USECOND)) { - dev_err(&edev->dev, - "timeout waiting for PM restore\n"); - return; - } - } - } - - /* Disable interrupts */ - writel(0, priv->base + INT_EN); - - writel(HW_CFG_SRST, priv->base + HW_CFG); - - start = get_time_ns(); - while(1) { - if (!(readl(priv->base + E2P_CMD) & E2P_CMD_EPC_BUSY)) - break; - if (is_timeout(start, 10 * MSECOND)) { - dev_err(&edev->dev, "reset timeout\n"); - return; - } - } - - /* Reset the FIFO level and flow control settings */ - smc911x_set_mac_csr(edev, FLOW, FLOW_FCPT | FLOW_FCEN); - - writel(0x0050287F, priv->base + AFC_CFG); - - /* Set to LED outputs */ - writel(0x70070000, priv->base + GPIO_CFG); -} - -static void smc911x_enable(struct eth_device *edev) -{ - struct smc911x_priv *priv = edev->priv; - - /* Enable TX */ - writel(8 << 16 | HW_CFG_SF, priv->base + HW_CFG); - - writel(GPT_CFG_TIMER_EN | 10000, priv->base + GPT_CFG); - - writel(TX_CFG_TX_ON, priv->base + TX_CFG); - - /* no padding to start of packets */ - writel(RX_CFG_RX_DUMP, priv->base + RX_CFG); -} - -static int smc911x_eth_open(struct eth_device *edev) -{ - struct smc911x_priv *priv = (struct smc911x_priv *)edev->priv; - - miidev_wait_aneg(&priv->miidev); - miidev_print_status(&priv->miidev); - - /* Turn on Tx + Rx */ - smc911x_enable(edev); - return 0; -} - -static int smc911x_eth_send(struct eth_device *edev, void *packet, int length) -{ - struct smc911x_priv *priv = (struct smc911x_priv *)edev->priv; - u32 *data = (u32*)packet; - u32 tmplen; - u32 status; - uint64_t start; - - writel(TX_CMD_A_INT_FIRST_SEG | TX_CMD_A_INT_LAST_SEG | length, - priv->base + TX_DATA_FIFO); - writel(length, priv->base + TX_DATA_FIFO); - - tmplen = (length + 3) / 4; - - while(tmplen--) - writel(*data++, priv->base + TX_DATA_FIFO); - - /* wait for transmission */ - start = get_time_ns(); - while (1) { - if ((readl(priv->base + TX_FIFO_INF) & - TX_FIFO_INF_TSUSED) >> 16) - break; - if (is_timeout(start, 100 * MSECOND)) { - dev_err(&edev->dev, "TX timeout\n"); - return -1; - } - } - - /* get status. Ignore 'no carrier' error, it has no meaning for - * full duplex operation - */ - status = readl(priv->base + TX_STATUS_FIFO) & (TX_STS_LOC | - TX_STS_LATE_COLL | TX_STS_MANY_COLL | TX_STS_MANY_DEFER | - TX_STS_UNDERRUN); - - if(!status) - return 0; - - dev_err(&edev->dev, "failed to send packet: %s%s%s%s%s\n", - status & TX_STS_LOC ? "TX_STS_LOC " : "", - status & TX_STS_LATE_COLL ? "TX_STS_LATE_COLL " : "", - status & TX_STS_MANY_COLL ? "TX_STS_MANY_COLL " : "", - status & TX_STS_MANY_DEFER ? "TX_STS_MANY_DEFER " : "", - status & TX_STS_UNDERRUN ? "TX_STS_UNDERRUN" : ""); - - return -1; -} - -static void smc911x_eth_halt(struct eth_device *edev) -{ - struct smc911x_priv *priv = (struct smc911x_priv *)edev->priv; - - /* Disable TX */ - writel(TX_CFG_STOP_TX, priv->base + TX_CFG); - -// smc911x_reset(edev); -} - -static int smc911x_eth_rx(struct eth_device *edev) -{ - struct smc911x_priv *priv = (struct smc911x_priv *)edev->priv; - u32 *data = (u32 *)NetRxPackets[0]; - u32 pktlen, tmplen; - u32 status; - - if((readl(priv->base + RX_FIFO_INF) & RX_FIFO_INF_RXSUSED) >> 16) { - status = readl(priv->base + RX_STATUS_FIFO); - pktlen = (status & RX_STS_PKT_LEN) >> 16; - - writel(0, priv->base + RX_CFG); - - tmplen = (pktlen + 2 + 3) / 4; - while(tmplen--) - *data++ = readl(priv->base + RX_DATA_FIFO); - - if(status & RX_STS_ES) - dev_err(&edev->dev, "dropped bad packet. Status: 0x%08x\n", - status); - else - net_receive(NetRxPackets[0], pktlen); - } - - return 0; -} - -static int smc911x_init_dev(struct eth_device *edev) -{ - struct smc911x_priv *priv = (struct smc911x_priv *)edev->priv; - - smc911x_set_mac_csr(edev, MAC_CR, MAC_CR_TXEN | MAC_CR_RXEN | - MAC_CR_HBDIS); - - miidev_restart_aneg(&priv->miidev); - - return 0; -} - -static int smc911x_probe(struct device_d *dev) -{ - struct eth_device *edev; - struct smc911x_priv *priv; - uint32_t val; - int i; - void __iomem *base; - - base = dev_request_mem_region(dev, 0); - - val = readl(base + BYTE_TEST); - if(val != 0x87654321) { - dev_err(dev, "no smc911x found on 0x%p (byte_test=0x%08x)\n", - base, val); - return -ENODEV; - } - - val = readl(base + ID_REV) >> 16; - for(i = 0; chip_ids[i].id != 0; i++) { - if (chip_ids[i].id == val) break; - } - if (!chip_ids[i].id) { - dev_err(dev, "Unknown chip ID %04x\n", val); - return -ENODEV; - } - - dev_info(dev, "detected %s controller\n", chip_ids[i].name); - - priv = xzalloc(sizeof(*priv)); - edev = &priv->edev; - edev->priv = priv; - - edev->init = smc911x_init_dev; - edev->open = smc911x_eth_open; - edev->send = smc911x_eth_send; - edev->recv = smc911x_eth_rx; - edev->halt = smc911x_eth_halt; - edev->get_ethaddr = smc911x_get_ethaddr; - edev->set_ethaddr = smc911x_set_ethaddr; - edev->parent = dev; - - priv->miidev.read = smc911x_phy_read; - priv->miidev.write = smc911x_phy_write; - priv->miidev.address = 1; - priv->miidev.flags = 0; - priv->miidev.edev = edev; - priv->miidev.parent = dev; - priv->base = base; - - smc911x_reset(edev); - smc911x_phy_reset(edev); - - mii_register(&priv->miidev); - eth_register(edev); - - return 0; -} - -static struct driver_d smc911x_driver = { - .name = "smc911x", - .probe = smc911x_probe, -}; - -static int smc911x_init(void) -{ - register_driver(&smc911x_driver); - return 0; -} - -device_initcall(smc911x_init); -- 1.7.10.4 _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH 0/7] smsc911x: runtime configuration improvement
@ 2012-08-14 17:25 Jean-Christophe PLAGNIOL-VILLARD
2012-08-14 17:32 ` [PATCH 1/7] smc911x: move register define to smc911x.h Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 1 reply; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-08-14 17:25 UTC (permalink / raw)
To: barebox
Hi,
please pull
The following changes since commit 3f96b4938c4046590be8a38fb114148c4bf1ca8e:
Merge tag 'bootm_fix' of git://git.jcrosoft.org/barebox (2012-08-13 20:37:53 +0200)
are available in the git repository at:
git://git.jcrosoft.org/barebox.git tags/smc911x_improve
for you to fetch changes up to 865ba468b906292c0158b8734dee5a31688e332b:
smm911x: check if the device is ready before using it (2012-08-15 01:19:54 +0800)
----------------------------------------------------------------
smsc911x: runtime configuration improvement
This patch series allow to detect and configure the drivers at the runtime
- Check if the device is ready before using it
- Update chip detection (take from the kernel 3.5)
- improve detection handle to detect bus configuration and swap
- add support to pass the shift via platform data
- add 16bit bus width support
- introduce read/write ops
- move register define to smc911x.h
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
----------------------------------------------------------------
Jean-Christophe PLAGNIOL-VILLARD (7):
smc911x: move register define to smc911x.h
smc911x: introduce read/write ops
smc911x: add 16bit bus width support
smc911x: add support to pass the shift via platform data
smc911x: improve detection handle
smc911x: update chip detection
smm911x: check if the device is ready before using it
arch/blackfin/boards/ipe337/ipe337.c | 7 +-
drivers/net/Kconfig | 6 --
drivers/net/smc911x.c | 569 ++++++++++++++++++++++++++++++++++++++++++++++++---------------------------------------------------------------------------------------------------------
drivers/net/smc911x.h | 364 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
include/smc911x.h | 18 +++++
5 files changed, 567 insertions(+), 397 deletions(-)
create mode 100644 drivers/net/smc911x.h
create mode 100644 include/smc911x.h
Best Regards,
J.
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* [PATCH 1/7] smc911x: move register define to smc911x.h 2012-08-14 17:25 [PATCH 0/7] smsc911x: runtime configuration improvement Jean-Christophe PLAGNIOL-VILLARD @ 2012-08-14 17:32 ` Jean-Christophe PLAGNIOL-VILLARD 2012-08-14 20:19 ` Sascha Hauer 0 siblings, 1 reply; 13+ messages in thread From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-08-14 17:32 UTC (permalink / raw) To: barebox this make the driver more readable Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> --- drivers/net/smc911x.c | 329 +-------------------------- drivers/net/{smc911x.c => smc911x.h} | 406 ---------------------------------- 2 files changed, 2 insertions(+), 733 deletions(-) copy drivers/net/{smc911x.c => smc911x.h} (60%) diff --git a/drivers/net/smc911x.c b/drivers/net/smc911x.c index 7dddbbc..9c488c7 100644 --- a/drivers/net/smc911x.c +++ b/drivers/net/smc911x.c @@ -38,334 +38,9 @@ #include <clock.h> #include <io.h> -#define AS CONFIG_DRIVER_NET_SMC911X_ADDRESS_SHIFT -/* Below are the register offsets and bit definitions - * of the Lan911x memory space - */ -#define RX_DATA_FIFO (0x00 << AS) - -#define TX_DATA_FIFO (0x20 << AS) -#define TX_CMD_A_INT_ON_COMP 0x80000000 -#define TX_CMD_A_INT_BUF_END_ALGN 0x03000000 -#define TX_CMD_A_INT_4_BYTE_ALGN 0x00000000 -#define TX_CMD_A_INT_16_BYTE_ALGN 0x01000000 -#define TX_CMD_A_INT_32_BYTE_ALGN 0x02000000 -#define TX_CMD_A_INT_DATA_OFFSET 0x001F0000 -#define TX_CMD_A_INT_FIRST_SEG 0x00002000 -#define TX_CMD_A_INT_LAST_SEG 0x00001000 -#define TX_CMD_A_BUF_SIZE 0x000007FF -#define TX_CMD_B_PKT_TAG 0xFFFF0000 -#define TX_CMD_B_ADD_CRC_DISABLE 0x00002000 -#define TX_CMD_B_DISABLE_PADDING 0x00001000 -#define TX_CMD_B_PKT_BYTE_LENGTH 0x000007FF - -#define RX_STATUS_FIFO (0x40 << AS) -#define RX_STS_PKT_LEN 0x3FFF0000 -#define RX_STS_ES 0x00008000 -#define RX_STS_BCST 0x00002000 -#define RX_STS_LEN_ERR 0x00001000 -#define RX_STS_RUNT_ERR 0x00000800 -#define RX_STS_MCAST 0x00000400 -#define RX_STS_TOO_LONG 0x00000080 -#define RX_STS_COLL 0x00000040 -#define RX_STS_ETH_TYPE 0x00000020 -#define RX_STS_WDOG_TMT 0x00000010 -#define RX_STS_MII_ERR 0x00000008 -#define RX_STS_DRIBBLING 0x00000004 -#define RX_STS_CRC_ERR 0x00000002 -#define RX_STATUS_FIFO_PEEK (0x44 << AS) -#define TX_STATUS_FIFO (0x48 << AS) -#define TX_STS_TAG 0xFFFF0000 -#define TX_STS_ES 0x00008000 -#define TX_STS_LOC 0x00000800 -#define TX_STS_NO_CARR 0x00000400 -#define TX_STS_LATE_COLL 0x00000200 -#define TX_STS_MANY_COLL 0x00000100 -#define TX_STS_COLL_CNT 0x00000078 -#define TX_STS_MANY_DEFER 0x00000004 -#define TX_STS_UNDERRUN 0x00000002 -#define TX_STS_DEFERRED 0x00000001 -#define TX_STATUS_FIFO_PEEK (0x4C << AS) -#define ID_REV (0x50 << AS) -#define ID_REV_CHIP_ID 0xFFFF0000 /* RO */ -#define ID_REV_REV_ID 0x0000FFFF /* RO */ - -#define INT_CFG (0x54 << AS) -#define INT_CFG_INT_DEAS 0xFF000000 /* R/W */ -#define INT_CFG_INT_DEAS_CLR 0x00004000 -#define INT_CFG_INT_DEAS_STS 0x00002000 -#define INT_CFG_IRQ_INT 0x00001000 /* RO */ -#define INT_CFG_IRQ_EN 0x00000100 /* R/W */ -#define INT_CFG_IRQ_POL 0x00000010 /* R/W Not Affected by SW Reset */ -#define INT_CFG_IRQ_TYPE 0x00000001 /* R/W Not Affected by SW Reset */ - -#define INT_STS (0x58 << AS) -#define INT_STS_SW_INT 0x80000000 /* R/WC */ -#define INT_STS_TXSTOP_INT 0x02000000 /* R/WC */ -#define INT_STS_RXSTOP_INT 0x01000000 /* R/WC */ -#define INT_STS_RXDFH_INT 0x00800000 /* R/WC */ -#define INT_STS_RXDF_INT 0x00400000 /* R/WC */ -#define INT_STS_TX_IOC 0x00200000 /* R/WC */ -#define INT_STS_RXD_INT 0x00100000 /* R/WC */ -#define INT_STS_GPT_INT 0x00080000 /* R/WC */ -#define INT_STS_PHY_INT 0x00040000 /* RO */ -#define INT_STS_PME_INT 0x00020000 /* R/WC */ -#define INT_STS_TXSO 0x00010000 /* R/WC */ -#define INT_STS_RWT 0x00008000 /* R/WC */ -#define INT_STS_RXE 0x00004000 /* R/WC */ -#define INT_STS_TXE 0x00002000 /* R/WC */ -//#define INT_STS_ERX 0x00001000 /* R/WC */ -#define INT_STS_TDFU 0x00000800 /* R/WC */ -#define INT_STS_TDFO 0x00000400 /* R/WC */ -#define INT_STS_TDFA 0x00000200 /* R/WC */ -#define INT_STS_TSFF 0x00000100 /* R/WC */ -#define INT_STS_TSFL 0x00000080 /* R/WC */ -//#define INT_STS_RXDF 0x00000040 /* R/WC */ -#define INT_STS_RDFO 0x00000040 /* R/WC */ -#define INT_STS_RDFL 0x00000020 /* R/WC */ -#define INT_STS_RSFF 0x00000010 /* R/WC */ -#define INT_STS_RSFL 0x00000008 /* R/WC */ -#define INT_STS_GPIO2_INT 0x00000004 /* R/WC */ -#define INT_STS_GPIO1_INT 0x00000002 /* R/WC */ -#define INT_STS_GPIO0_INT 0x00000001 /* R/WC */ -#define INT_EN (0x5C << AS) -#define INT_EN_SW_INT_EN 0x80000000 /* R/W */ -#define INT_EN_TXSTOP_INT_EN 0x02000000 /* R/W */ -#define INT_EN_RXSTOP_INT_EN 0x01000000 /* R/W */ -#define INT_EN_RXDFH_INT_EN 0x00800000 /* R/W */ -//#define INT_EN_RXDF_INT_EN 0x00400000 /* R/W */ -#define INT_EN_TIOC_INT_EN 0x00200000 /* R/W */ -#define INT_EN_RXD_INT_EN 0x00100000 /* R/W */ -#define INT_EN_GPT_INT_EN 0x00080000 /* R/W */ -#define INT_EN_PHY_INT_EN 0x00040000 /* R/W */ -#define INT_EN_PME_INT_EN 0x00020000 /* R/W */ -#define INT_EN_TXSO_EN 0x00010000 /* R/W */ -#define INT_EN_RWT_EN 0x00008000 /* R/W */ -#define INT_EN_RXE_EN 0x00004000 /* R/W */ -#define INT_EN_TXE_EN 0x00002000 /* R/W */ -//#define INT_EN_ERX_EN 0x00001000 /* R/W */ -#define INT_EN_TDFU_EN 0x00000800 /* R/W */ -#define INT_EN_TDFO_EN 0x00000400 /* R/W */ -#define INT_EN_TDFA_EN 0x00000200 /* R/W */ -#define INT_EN_TSFF_EN 0x00000100 /* R/W */ -#define INT_EN_TSFL_EN 0x00000080 /* R/W */ -//#define INT_EN_RXDF_EN 0x00000040 /* R/W */ -#define INT_EN_RDFO_EN 0x00000040 /* R/W */ -#define INT_EN_RDFL_EN 0x00000020 /* R/W */ -#define INT_EN_RSFF_EN 0x00000010 /* R/W */ -#define INT_EN_RSFL_EN 0x00000008 /* R/W */ -#define INT_EN_GPIO2_INT 0x00000004 /* R/W */ -#define INT_EN_GPIO1_INT 0x00000002 /* R/W */ -#define INT_EN_GPIO0_INT 0x00000001 /* R/W */ - -#define BYTE_TEST (0x64 << AS) -#define FIFO_INT (0x68 << AS) -#define FIFO_INT_TX_AVAIL_LEVEL 0xFF000000 /* R/W */ -#define FIFO_INT_TX_STS_LEVEL 0x00FF0000 /* R/W */ -#define FIFO_INT_RX_AVAIL_LEVEL 0x0000FF00 /* R/W */ -#define FIFO_INT_RX_STS_LEVEL 0x000000FF /* R/W */ - -#define RX_CFG (0x6C << AS) -#define RX_CFG_RX_END_ALGN 0xC0000000 /* R/W */ -#define RX_CFG_RX_END_ALGN4 0x00000000 /* R/W */ -#define RX_CFG_RX_END_ALGN16 0x40000000 /* R/W */ -#define RX_CFG_RX_END_ALGN32 0x80000000 /* R/W */ -#define RX_CFG_RX_DMA_CNT 0x0FFF0000 /* R/W */ -#define RX_CFG_RX_DUMP 0x00008000 /* R/W */ -#define RX_CFG_RXDOFF 0x00001F00 /* R/W */ -//#define RX_CFG_RXBAD 0x00000001 /* R/W */ - -#define TX_CFG (0x70 << AS) -//#define TX_CFG_TX_DMA_LVL 0xE0000000 /* R/W */ -//#define TX_CFG_TX_DMA_CNT 0x0FFF0000 /* R/W Self Clearing */ -#define TX_CFG_TXS_DUMP 0x00008000 /* Self Clearing */ -#define TX_CFG_TXD_DUMP 0x00004000 /* Self Clearing */ -#define TX_CFG_TXSAO 0x00000004 /* R/W */ -#define TX_CFG_TX_ON 0x00000002 /* R/W */ -#define TX_CFG_STOP_TX 0x00000001 /* Self Clearing */ - -#define HW_CFG (0x74 << AS) -#define HW_CFG_TTM 0x00200000 /* R/W */ -#define HW_CFG_SF 0x00100000 /* R/W */ -#define HW_CFG_TX_FIF_SZ 0x000F0000 /* R/W */ -#define HW_CFG_TR 0x00003000 /* R/W */ -#define HW_CFG_PHY_CLK_SEL 0x00000060 /* R/W */ -#define HW_CFG_PHY_CLK_SEL_INT_PHY 0x00000000 /* R/W */ -#define HW_CFG_PHY_CLK_SEL_EXT_PHY 0x00000020 /* R/W */ -#define HW_CFG_PHY_CLK_SEL_CLK_DIS 0x00000040 /* R/W */ -#define HW_CFG_SMI_SEL 0x00000010 /* R/W */ -#define HW_CFG_EXT_PHY_DET 0x00000008 /* RO */ -#define HW_CFG_EXT_PHY_EN 0x00000004 /* R/W */ -#define HW_CFG_32_16_BIT_MODE 0x00000004 /* RO */ -#define HW_CFG_SRST_TO 0x00000002 /* RO */ -#define HW_CFG_SRST 0x00000001 /* Self Clearing */ - -#define RX_DP_CTRL (0x78 << AS) -#define RX_DP_CTRL_RX_FFWD 0x80000000 /* R/W */ -#define RX_DP_CTRL_FFWD_BUSY 0x80000000 /* RO */ - -#define RX_FIFO_INF (0x7C << AS) -#define RX_FIFO_INF_RXSUSED 0x00FF0000 /* RO */ -#define RX_FIFO_INF_RXDUSED 0x0000FFFF /* RO */ - -#define TX_FIFO_INF (0x80 << AS) -#define TX_FIFO_INF_TSUSED 0x00FF0000 /* RO */ -#define TX_FIFO_INF_TDFREE 0x0000FFFF /* RO */ - -#define PMT_CTRL (0x84 << AS) -#define PMT_CTRL_PM_MODE 0x00003000 /* Self Clearing */ -#define PMT_CTRL_PHY_RST 0x00000400 /* Self Clearing */ -#define PMT_CTRL_WOL_EN 0x00000200 /* R/W */ -#define PMT_CTRL_ED_EN 0x00000100 /* R/W */ -#define PMT_CTRL_PME_TYPE 0x00000040 /* R/W Not Affected by SW Reset */ -#define PMT_CTRL_WUPS 0x00000030 /* R/WC */ -#define PMT_CTRL_WUPS_NOWAKE 0x00000000 /* R/WC */ -#define PMT_CTRL_WUPS_ED 0x00000010 /* R/WC */ -#define PMT_CTRL_WUPS_WOL 0x00000020 /* R/WC */ -#define PMT_CTRL_WUPS_MULTI 0x00000030 /* R/WC */ -#define PMT_CTRL_PME_IND 0x00000008 /* R/W */ -#define PMT_CTRL_PME_POL 0x00000004 /* R/W */ -#define PMT_CTRL_PME_EN 0x00000002 /* R/W Not Affected by SW Reset */ -#define PMT_CTRL_READY 0x00000001 /* RO */ - -#define GPIO_CFG (0x88 << AS) -#define GPIO_CFG_LED3_EN 0x40000000 /* R/W */ -#define GPIO_CFG_LED2_EN 0x20000000 /* R/W */ -#define GPIO_CFG_LED1_EN 0x10000000 /* R/W */ -#define GPIO_CFG_GPIO2_INT_POL 0x04000000 /* R/W */ -#define GPIO_CFG_GPIO1_INT_POL 0x02000000 /* R/W */ -#define GPIO_CFG_GPIO0_INT_POL 0x01000000 /* R/W */ -#define GPIO_CFG_EEPR_EN 0x00700000 /* R/W */ -#define GPIO_CFG_GPIOBUF2 0x00040000 /* R/W */ -#define GPIO_CFG_GPIOBUF1 0x00020000 /* R/W */ -#define GPIO_CFG_GPIOBUF0 0x00010000 /* R/W */ -#define GPIO_CFG_GPIODIR2 0x00000400 /* R/W */ -#define GPIO_CFG_GPIODIR1 0x00000200 /* R/W */ -#define GPIO_CFG_GPIODIR0 0x00000100 /* R/W */ -#define GPIO_CFG_GPIOD4 0x00000010 /* R/W */ -#define GPIO_CFG_GPIOD3 0x00000008 /* R/W */ -#define GPIO_CFG_GPIOD2 0x00000004 /* R/W */ -#define GPIO_CFG_GPIOD1 0x00000002 /* R/W */ -#define GPIO_CFG_GPIOD0 0x00000001 /* R/W */ - -#define GPT_CFG (0x8C << AS) -#define GPT_CFG_TIMER_EN 0x20000000 /* R/W */ -#define GPT_CFG_GPT_LOAD 0x0000FFFF /* R/W */ - -#define GPT_CNT (0x90 << AS) -#define GPT_CNT_GPT_CNT 0x0000FFFF /* RO */ - -#define ENDIAN (0x98 << AS) -#define FREE_RUN (0x9C << AS) -#define RX_DROP (0xA0 << AS) -#define MAC_CSR_CMD (0xA4 << AS) -#define MAC_CSR_CMD_CSR_BUSY 0x80000000 /* Self Clearing */ -#define MAC_CSR_CMD_R_NOT_W 0x40000000 /* R/W */ -#define MAC_CSR_CMD_CSR_ADDR 0x000000FF /* R/W */ - -#define MAC_CSR_DATA (0xA8 << AS) -#define AFC_CFG (0xAC << AS) -#define AFC_CFG_AFC_HI 0x00FF0000 /* R/W */ -#define AFC_CFG_AFC_LO 0x0000FF00 /* R/W */ -#define AFC_CFG_BACK_DUR 0x000000F0 /* R/W */ -#define AFC_CFG_FCMULT 0x00000008 /* R/W */ -#define AFC_CFG_FCBRD 0x00000004 /* R/W */ -#define AFC_CFG_FCADD 0x00000002 /* R/W */ -#define AFC_CFG_FCANY 0x00000001 /* R/W */ - -#define E2P_CMD (0xB0 << AS) -#define E2P_CMD_EPC_BUSY 0x80000000 /* Self Clearing */ -#define E2P_CMD_EPC_CMD 0x70000000 /* R/W */ -#define E2P_CMD_EPC_CMD_READ 0x00000000 /* R/W */ -#define E2P_CMD_EPC_CMD_EWDS 0x10000000 /* R/W */ -#define E2P_CMD_EPC_CMD_EWEN 0x20000000 /* R/W */ -#define E2P_CMD_EPC_CMD_WRITE 0x30000000 /* R/W */ -#define E2P_CMD_EPC_CMD_WRAL 0x40000000 /* R/W */ -#define E2P_CMD_EPC_CMD_ERASE 0x50000000 /* R/W */ -#define E2P_CMD_EPC_CMD_ERAL 0x60000000 /* R/W */ -#define E2P_CMD_EPC_CMD_RELOAD 0x70000000 /* R/W */ -#define E2P_CMD_EPC_TIMEOUT 0x00000200 /* RO */ -#define E2P_CMD_MAC_ADDR_LOADED 0x00000100 /* RO */ -#define E2P_CMD_EPC_ADDR 0x000000FF /* R/W */ - -#define E2P_DATA (0xB4 << AS) -#define E2P_DATA_EEPROM_DATA 0x000000FF /* R/W */ -/* end of LAN register offsets and bit definitions */ - -/* MAC Control and Status registers */ -#define MAC_CR 0x01 /* R/W */ - -/* MAC_CR - MAC Control Register */ -#define MAC_CR_RXALL 0x80000000 -// TODO: delete this bit? It is not described in the data sheet. -#define MAC_CR_HBDIS 0x10000000 -#define MAC_CR_RCVOWN 0x00800000 -#define MAC_CR_LOOPBK 0x00200000 -#define MAC_CR_FDPX 0x00100000 -#define MAC_CR_MCPAS 0x00080000 -#define MAC_CR_PRMS 0x00040000 -#define MAC_CR_INVFILT 0x00020000 -#define MAC_CR_PASSBAD 0x00010000 -#define MAC_CR_HFILT 0x00008000 -#define MAC_CR_HPFILT 0x00002000 -#define MAC_CR_LCOLL 0x00001000 -#define MAC_CR_BCAST 0x00000800 -#define MAC_CR_DISRTY 0x00000400 -#define MAC_CR_PADSTR 0x00000100 -#define MAC_CR_BOLMT_MASK 0x000000C0 -#define MAC_CR_DFCHK 0x00000020 -#define MAC_CR_TXEN 0x00000008 -#define MAC_CR_RXEN 0x00000004 - -#define ADDRH 0x02 /* R/W mask 0x0000FFFFUL */ -#define ADDRL 0x03 /* R/W mask 0xFFFFFFFFUL */ -#define HASHH 0x04 /* R/W */ -#define HASHL 0x05 /* R/W */ - -#define MII_ACC 0x06 /* R/W */ -#define MII_ACC_PHY_ADDR 0x0000F800 -#define MII_ACC_MIIRINDA 0x000007C0 -#define MII_ACC_MII_WRITE 0x00000002 -#define MII_ACC_MII_BUSY 0x00000001 - -#define MII_DATA 0x07 /* R/W mask 0x0000FFFFUL */ - -#ifdef FLOW -#undef FLOW /* clashed with include/asm/cpu/defBF561.h:1654 */ -#endif - -#define FLOW 0x08 /* R/W */ -#define FLOW_FCPT 0xFFFF0000 -#define FLOW_FCPASS 0x00000004 -#define FLOW_FCEN 0x00000002 -#define FLOW_FCBSY 0x00000001 - -#define VLAN1 0x09 /* R/W mask 0x0000FFFFUL */ -#define VLAN1_VTI1 0x0000ffff - -#define VLAN2 0x0A /* R/W mask 0x0000FFFFUL */ -#define VLAN2_VTI2 0x0000ffff - -#define WUFF 0x0B /* WO */ - -#define WUCSR 0x0C /* R/W */ -#define WUCSR_GUE 0x00000200 -#define WUCSR_WUFR 0x00000040 -#define WUCSR_MPR 0x00000020 -#define WUCSR_WAKE_EN 0x00000004 -#define WUCSR_MPEN 0x00000002 - -/* Chip ID values */ -#define CHIP_9115 0x115 -#define CHIP_9116 0x116 -#define CHIP_9117 0x117 -#define CHIP_9118 0x118 -#define CHIP_9215 0x115a -#define CHIP_9216 0x116a -#define CHIP_9217 0x117a -#define CHIP_9218 0x118a -#define CHIP_9221 0x9221 +#define AS CONFIG_DRIVER_NET_SMC911X_ADDRESS_SHIFT +#include "smc911x.h" struct smc911x_priv { struct eth_device edev; diff --git a/drivers/net/smc911x.c b/drivers/net/smc911x.h similarity index 60% copy from drivers/net/smc911x.c copy to drivers/net/smc911x.h index 7dddbbc..68f6590 100644 --- a/drivers/net/smc911x.c +++ b/drivers/net/smc911x.h @@ -22,24 +22,6 @@ * MA 02111-1307 USA */ -#ifdef CONFIG_ENABLE_DEVICE_NOISE -# define DEBUG -#endif - -#include <common.h> - -#include <command.h> -#include <net.h> -#include <miidev.h> -#include <malloc.h> -#include <init.h> -#include <xfuncs.h> -#include <errno.h> -#include <clock.h> -#include <io.h> - -#define AS CONFIG_DRIVER_NET_SMC911X_ADDRESS_SHIFT - /* Below are the register offsets and bit definitions * of the Lan911x memory space */ @@ -367,392 +349,4 @@ #define CHIP_9218 0x118a #define CHIP_9221 0x9221 -struct smc911x_priv { - struct eth_device edev; - struct mii_device miidev; - void __iomem *base; -}; - -struct chip_id { - u16 id; - char *name; -}; - -static const struct chip_id chip_ids[] = { - { CHIP_9115, "LAN9115" }, - { CHIP_9116, "LAN9116" }, - { CHIP_9117, "LAN9117" }, - { CHIP_9118, "LAN9118" }, - { CHIP_9215, "LAN9215" }, - { CHIP_9216, "LAN9216" }, - { CHIP_9217, "LAN9217" }, - { CHIP_9218, "LAN9218" }, - { CHIP_9221, "LAN9221" }, - { 0, NULL }, -}; - -#define DRIVERNAME "smc911x" - -static int smc911x_mac_wait_busy(struct smc911x_priv *priv) -{ - uint64_t start = get_time_ns(); - - while (!is_timeout(start, MSECOND)) { - if (!(readl(priv->base + MAC_CSR_CMD) & MAC_CSR_CMD_CSR_BUSY)) - return 0; - } - - printf("%s: mac timeout\n", __FUNCTION__); - return -1; -} - -static u32 smc911x_get_mac_csr(struct eth_device *edev, u8 reg) -{ - struct smc911x_priv *priv = edev->priv; - ulong val; - - smc911x_mac_wait_busy(priv); - - writel(MAC_CSR_CMD_CSR_BUSY | MAC_CSR_CMD_R_NOT_W | reg, - priv->base + MAC_CSR_CMD); - - smc911x_mac_wait_busy(priv); - - val = readl(priv->base + MAC_CSR_DATA); - - return val; -} - -static void smc911x_set_mac_csr(struct eth_device *edev, u8 reg, u32 data) -{ - struct smc911x_priv *priv = edev->priv; - - smc911x_mac_wait_busy(priv); - - writel(data, priv->base + MAC_CSR_DATA); - writel(MAC_CSR_CMD_CSR_BUSY | reg, priv->base + MAC_CSR_CMD); - - smc911x_mac_wait_busy(priv); -} - -static int smc911x_get_ethaddr(struct eth_device *edev, unsigned char *m) -{ - unsigned long addrh, addrl; - - addrh = smc911x_get_mac_csr(edev, ADDRH); - addrl = smc911x_get_mac_csr(edev, ADDRL); - - m[0] = (addrl ) & 0xff; - m[1] = (addrl >> 8 ) & 0xff; - m[2] = (addrl >> 16 ) & 0xff; - m[3] = (addrl >> 24 ) & 0xff; - m[4] = (addrh ) & 0xff; - m[5] = (addrh >> 8 ) & 0xff; - - /* we get 0xff when there is no eeprom connected */ - if ((m[0] & m[1] & m[2] & m[3] & m[4] & m[5]) == 0xff) - return -1; - - return 0; -} - -static int smc911x_set_ethaddr(struct eth_device *edev, unsigned char *m) -{ - unsigned long addrh, addrl; - - addrl = m[0] | m[1] << 8 | m[2] << 16 | m[3] << 24; - addrh = m[4] | m[5] << 8; - smc911x_set_mac_csr(edev, ADDRH, addrh); - smc911x_set_mac_csr(edev, ADDRL, addrl); - - return 0; -} - -static int smc911x_phy_read(struct mii_device *mdev, int phy_addr, int reg) -{ - struct eth_device *edev = mdev->edev; - - while (smc911x_get_mac_csr(edev, MII_ACC) & MII_ACC_MII_BUSY); - - smc911x_set_mac_csr(edev, MII_ACC, phy_addr << 11 | reg << 6 | - MII_ACC_MII_BUSY); - - while (smc911x_get_mac_csr(edev, MII_ACC) & MII_ACC_MII_BUSY); - - return smc911x_get_mac_csr(edev, MII_DATA); -} - -static int smc911x_phy_write(struct mii_device *mdev, int phy_addr, - int reg, int val) -{ - struct eth_device *edev = mdev->edev; - - while (smc911x_get_mac_csr(edev, MII_ACC) & MII_ACC_MII_BUSY); - - smc911x_set_mac_csr(edev, MII_DATA, val); - smc911x_set_mac_csr(edev, MII_ACC, - phy_addr << 11 | reg << 6 | MII_ACC_MII_BUSY | - MII_ACC_MII_WRITE); - - while (smc911x_get_mac_csr(edev, MII_ACC) & MII_ACC_MII_BUSY); - - return 0; -} - -static int smc911x_phy_reset(struct eth_device *edev) -{ - struct smc911x_priv *priv = edev->priv; - u32 reg; - - reg = readl(priv->base + PMT_CTRL); - reg &= 0xfcf; - reg |= PMT_CTRL_PHY_RST; - writel(reg, priv->base + PMT_CTRL); - - mdelay(100); - - return 0; -} - -static void smc911x_reset(struct eth_device *edev) -{ - struct smc911x_priv *priv = edev->priv; - uint64_t start; - - /* Take out of PM setting first */ - if (readl(priv->base + PMT_CTRL) & PMT_CTRL_READY) { - /* Write to the bytetest will take out of powerdown */ - writel(0, priv->base + BYTE_TEST); - - start = get_time_ns(); - while(1) { - if ((readl(priv->base + PMT_CTRL) & PMT_CTRL_READY)) - break; - if (is_timeout(start, 100 * USECOND)) { - dev_err(&edev->dev, - "timeout waiting for PM restore\n"); - return; - } - } - } - - /* Disable interrupts */ - writel(0, priv->base + INT_EN); - - writel(HW_CFG_SRST, priv->base + HW_CFG); - - start = get_time_ns(); - while(1) { - if (!(readl(priv->base + E2P_CMD) & E2P_CMD_EPC_BUSY)) - break; - if (is_timeout(start, 10 * MSECOND)) { - dev_err(&edev->dev, "reset timeout\n"); - return; - } - } - - /* Reset the FIFO level and flow control settings */ - smc911x_set_mac_csr(edev, FLOW, FLOW_FCPT | FLOW_FCEN); - - writel(0x0050287F, priv->base + AFC_CFG); - - /* Set to LED outputs */ - writel(0x70070000, priv->base + GPIO_CFG); -} - -static void smc911x_enable(struct eth_device *edev) -{ - struct smc911x_priv *priv = edev->priv; - - /* Enable TX */ - writel(8 << 16 | HW_CFG_SF, priv->base + HW_CFG); - - writel(GPT_CFG_TIMER_EN | 10000, priv->base + GPT_CFG); - - writel(TX_CFG_TX_ON, priv->base + TX_CFG); - - /* no padding to start of packets */ - writel(RX_CFG_RX_DUMP, priv->base + RX_CFG); -} - -static int smc911x_eth_open(struct eth_device *edev) -{ - struct smc911x_priv *priv = (struct smc911x_priv *)edev->priv; - - miidev_wait_aneg(&priv->miidev); - miidev_print_status(&priv->miidev); - - /* Turn on Tx + Rx */ - smc911x_enable(edev); - return 0; -} - -static int smc911x_eth_send(struct eth_device *edev, void *packet, int length) -{ - struct smc911x_priv *priv = (struct smc911x_priv *)edev->priv; - u32 *data = (u32*)packet; - u32 tmplen; - u32 status; - uint64_t start; - - writel(TX_CMD_A_INT_FIRST_SEG | TX_CMD_A_INT_LAST_SEG | length, - priv->base + TX_DATA_FIFO); - writel(length, priv->base + TX_DATA_FIFO); - - tmplen = (length + 3) / 4; - - while(tmplen--) - writel(*data++, priv->base + TX_DATA_FIFO); - - /* wait for transmission */ - start = get_time_ns(); - while (1) { - if ((readl(priv->base + TX_FIFO_INF) & - TX_FIFO_INF_TSUSED) >> 16) - break; - if (is_timeout(start, 100 * MSECOND)) { - dev_err(&edev->dev, "TX timeout\n"); - return -1; - } - } - - /* get status. Ignore 'no carrier' error, it has no meaning for - * full duplex operation - */ - status = readl(priv->base + TX_STATUS_FIFO) & (TX_STS_LOC | - TX_STS_LATE_COLL | TX_STS_MANY_COLL | TX_STS_MANY_DEFER | - TX_STS_UNDERRUN); - - if(!status) - return 0; - - dev_err(&edev->dev, "failed to send packet: %s%s%s%s%s\n", - status & TX_STS_LOC ? "TX_STS_LOC " : "", - status & TX_STS_LATE_COLL ? "TX_STS_LATE_COLL " : "", - status & TX_STS_MANY_COLL ? "TX_STS_MANY_COLL " : "", - status & TX_STS_MANY_DEFER ? "TX_STS_MANY_DEFER " : "", - status & TX_STS_UNDERRUN ? "TX_STS_UNDERRUN" : ""); - - return -1; -} - -static void smc911x_eth_halt(struct eth_device *edev) -{ - struct smc911x_priv *priv = (struct smc911x_priv *)edev->priv; - - /* Disable TX */ - writel(TX_CFG_STOP_TX, priv->base + TX_CFG); - -// smc911x_reset(edev); -} - -static int smc911x_eth_rx(struct eth_device *edev) -{ - struct smc911x_priv *priv = (struct smc911x_priv *)edev->priv; - u32 *data = (u32 *)NetRxPackets[0]; - u32 pktlen, tmplen; - u32 status; - - if((readl(priv->base + RX_FIFO_INF) & RX_FIFO_INF_RXSUSED) >> 16) { - status = readl(priv->base + RX_STATUS_FIFO); - pktlen = (status & RX_STS_PKT_LEN) >> 16; - - writel(0, priv->base + RX_CFG); - - tmplen = (pktlen + 2 + 3) / 4; - while(tmplen--) - *data++ = readl(priv->base + RX_DATA_FIFO); - - if(status & RX_STS_ES) - dev_err(&edev->dev, "dropped bad packet. Status: 0x%08x\n", - status); - else - net_receive(NetRxPackets[0], pktlen); - } - - return 0; -} - -static int smc911x_init_dev(struct eth_device *edev) -{ - struct smc911x_priv *priv = (struct smc911x_priv *)edev->priv; - - smc911x_set_mac_csr(edev, MAC_CR, MAC_CR_TXEN | MAC_CR_RXEN | - MAC_CR_HBDIS); - - miidev_restart_aneg(&priv->miidev); - - return 0; -} - -static int smc911x_probe(struct device_d *dev) -{ - struct eth_device *edev; - struct smc911x_priv *priv; - uint32_t val; - int i; - void __iomem *base; - - base = dev_request_mem_region(dev, 0); - - val = readl(base + BYTE_TEST); - if(val != 0x87654321) { - dev_err(dev, "no smc911x found on 0x%p (byte_test=0x%08x)\n", - base, val); - return -ENODEV; - } - - val = readl(base + ID_REV) >> 16; - for(i = 0; chip_ids[i].id != 0; i++) { - if (chip_ids[i].id == val) break; - } - if (!chip_ids[i].id) { - dev_err(dev, "Unknown chip ID %04x\n", val); - return -ENODEV; - } - - dev_info(dev, "detected %s controller\n", chip_ids[i].name); - - priv = xzalloc(sizeof(*priv)); - edev = &priv->edev; - edev->priv = priv; - - edev->init = smc911x_init_dev; - edev->open = smc911x_eth_open; - edev->send = smc911x_eth_send; - edev->recv = smc911x_eth_rx; - edev->halt = smc911x_eth_halt; - edev->get_ethaddr = smc911x_get_ethaddr; - edev->set_ethaddr = smc911x_set_ethaddr; - edev->parent = dev; - - priv->miidev.read = smc911x_phy_read; - priv->miidev.write = smc911x_phy_write; - priv->miidev.address = 1; - priv->miidev.flags = 0; - priv->miidev.edev = edev; - priv->miidev.parent = dev; - priv->base = base; - - smc911x_reset(edev); - smc911x_phy_reset(edev); - - mii_register(&priv->miidev); - eth_register(edev); - - return 0; -} - -static struct driver_d smc911x_driver = { - .name = "smc911x", - .probe = smc911x_probe, -}; - -static int smc911x_init(void) -{ - register_driver(&smc911x_driver); - return 0; -} - -device_initcall(smc911x_init); -- 1.7.10.4 _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH 1/7] smc911x: move register define to smc911x.h 2012-08-14 17:32 ` [PATCH 1/7] smc911x: move register define to smc911x.h Jean-Christophe PLAGNIOL-VILLARD @ 2012-08-14 20:19 ` Sascha Hauer 2012-08-15 4:34 ` Jean-Christophe PLAGNIOL-VILLARD 0 siblings, 1 reply; 13+ messages in thread From: Sascha Hauer @ 2012-08-14 20:19 UTC (permalink / raw) To: Jean-Christophe PLAGNIOL-VILLARD; +Cc: barebox On Tue, Aug 14, 2012 at 07:32:14PM +0200, Jean-Christophe PLAGNIOL-VILLARD wrote: > this make the driver more readable > > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> > --- > drivers/net/smc911x.c | 329 +-------------------------- > drivers/net/{smc911x.c => smc911x.h} | 406 ---------------------------------- > 2 files changed, 2 insertions(+), 733 deletions(-) > copy drivers/net/{smc911x.c => smc911x.h} (60%) This is only churn. Please drop. Sascha > > diff --git a/drivers/net/smc911x.c b/drivers/net/smc911x.c > index 7dddbbc..9c488c7 100644 > --- a/drivers/net/smc911x.c > +++ b/drivers/net/smc911x.c > @@ -38,334 +38,9 @@ > #include <clock.h> > #include <io.h> > > -#define AS CONFIG_DRIVER_NET_SMC911X_ADDRESS_SHIFT > > -/* Below are the register offsets and bit definitions > - * of the Lan911x memory space > - */ > -#define RX_DATA_FIFO (0x00 << AS) > - > -#define TX_DATA_FIFO (0x20 << AS) > -#define TX_CMD_A_INT_ON_COMP 0x80000000 > -#define TX_CMD_A_INT_BUF_END_ALGN 0x03000000 > -#define TX_CMD_A_INT_4_BYTE_ALGN 0x00000000 > -#define TX_CMD_A_INT_16_BYTE_ALGN 0x01000000 > -#define TX_CMD_A_INT_32_BYTE_ALGN 0x02000000 > -#define TX_CMD_A_INT_DATA_OFFSET 0x001F0000 > -#define TX_CMD_A_INT_FIRST_SEG 0x00002000 > -#define TX_CMD_A_INT_LAST_SEG 0x00001000 > -#define TX_CMD_A_BUF_SIZE 0x000007FF > -#define TX_CMD_B_PKT_TAG 0xFFFF0000 > -#define TX_CMD_B_ADD_CRC_DISABLE 0x00002000 > -#define TX_CMD_B_DISABLE_PADDING 0x00001000 > -#define TX_CMD_B_PKT_BYTE_LENGTH 0x000007FF > - > -#define RX_STATUS_FIFO (0x40 << AS) > -#define RX_STS_PKT_LEN 0x3FFF0000 > -#define RX_STS_ES 0x00008000 > -#define RX_STS_BCST 0x00002000 > -#define RX_STS_LEN_ERR 0x00001000 > -#define RX_STS_RUNT_ERR 0x00000800 > -#define RX_STS_MCAST 0x00000400 > -#define RX_STS_TOO_LONG 0x00000080 > -#define RX_STS_COLL 0x00000040 > -#define RX_STS_ETH_TYPE 0x00000020 > -#define RX_STS_WDOG_TMT 0x00000010 > -#define RX_STS_MII_ERR 0x00000008 > -#define RX_STS_DRIBBLING 0x00000004 > -#define RX_STS_CRC_ERR 0x00000002 > -#define RX_STATUS_FIFO_PEEK (0x44 << AS) > -#define TX_STATUS_FIFO (0x48 << AS) > -#define TX_STS_TAG 0xFFFF0000 > -#define TX_STS_ES 0x00008000 > -#define TX_STS_LOC 0x00000800 > -#define TX_STS_NO_CARR 0x00000400 > -#define TX_STS_LATE_COLL 0x00000200 > -#define TX_STS_MANY_COLL 0x00000100 > -#define TX_STS_COLL_CNT 0x00000078 > -#define TX_STS_MANY_DEFER 0x00000004 > -#define TX_STS_UNDERRUN 0x00000002 > -#define TX_STS_DEFERRED 0x00000001 > -#define TX_STATUS_FIFO_PEEK (0x4C << AS) > -#define ID_REV (0x50 << AS) > -#define ID_REV_CHIP_ID 0xFFFF0000 /* RO */ > -#define ID_REV_REV_ID 0x0000FFFF /* RO */ > - > -#define INT_CFG (0x54 << AS) > -#define INT_CFG_INT_DEAS 0xFF000000 /* R/W */ > -#define INT_CFG_INT_DEAS_CLR 0x00004000 > -#define INT_CFG_INT_DEAS_STS 0x00002000 > -#define INT_CFG_IRQ_INT 0x00001000 /* RO */ > -#define INT_CFG_IRQ_EN 0x00000100 /* R/W */ > -#define INT_CFG_IRQ_POL 0x00000010 /* R/W Not Affected by SW Reset */ > -#define INT_CFG_IRQ_TYPE 0x00000001 /* R/W Not Affected by SW Reset */ > - > -#define INT_STS (0x58 << AS) > -#define INT_STS_SW_INT 0x80000000 /* R/WC */ > -#define INT_STS_TXSTOP_INT 0x02000000 /* R/WC */ > -#define INT_STS_RXSTOP_INT 0x01000000 /* R/WC */ > -#define INT_STS_RXDFH_INT 0x00800000 /* R/WC */ > -#define INT_STS_RXDF_INT 0x00400000 /* R/WC */ > -#define INT_STS_TX_IOC 0x00200000 /* R/WC */ > -#define INT_STS_RXD_INT 0x00100000 /* R/WC */ > -#define INT_STS_GPT_INT 0x00080000 /* R/WC */ > -#define INT_STS_PHY_INT 0x00040000 /* RO */ > -#define INT_STS_PME_INT 0x00020000 /* R/WC */ > -#define INT_STS_TXSO 0x00010000 /* R/WC */ > -#define INT_STS_RWT 0x00008000 /* R/WC */ > -#define INT_STS_RXE 0x00004000 /* R/WC */ > -#define INT_STS_TXE 0x00002000 /* R/WC */ > -//#define INT_STS_ERX 0x00001000 /* R/WC */ > -#define INT_STS_TDFU 0x00000800 /* R/WC */ > -#define INT_STS_TDFO 0x00000400 /* R/WC */ > -#define INT_STS_TDFA 0x00000200 /* R/WC */ > -#define INT_STS_TSFF 0x00000100 /* R/WC */ > -#define INT_STS_TSFL 0x00000080 /* R/WC */ > -//#define INT_STS_RXDF 0x00000040 /* R/WC */ > -#define INT_STS_RDFO 0x00000040 /* R/WC */ > -#define INT_STS_RDFL 0x00000020 /* R/WC */ > -#define INT_STS_RSFF 0x00000010 /* R/WC */ > -#define INT_STS_RSFL 0x00000008 /* R/WC */ > -#define INT_STS_GPIO2_INT 0x00000004 /* R/WC */ > -#define INT_STS_GPIO1_INT 0x00000002 /* R/WC */ > -#define INT_STS_GPIO0_INT 0x00000001 /* R/WC */ > -#define INT_EN (0x5C << AS) > -#define INT_EN_SW_INT_EN 0x80000000 /* R/W */ > -#define INT_EN_TXSTOP_INT_EN 0x02000000 /* R/W */ > -#define INT_EN_RXSTOP_INT_EN 0x01000000 /* R/W */ > -#define INT_EN_RXDFH_INT_EN 0x00800000 /* R/W */ > -//#define INT_EN_RXDF_INT_EN 0x00400000 /* R/W */ > -#define INT_EN_TIOC_INT_EN 0x00200000 /* R/W */ > -#define INT_EN_RXD_INT_EN 0x00100000 /* R/W */ > -#define INT_EN_GPT_INT_EN 0x00080000 /* R/W */ > -#define INT_EN_PHY_INT_EN 0x00040000 /* R/W */ > -#define INT_EN_PME_INT_EN 0x00020000 /* R/W */ > -#define INT_EN_TXSO_EN 0x00010000 /* R/W */ > -#define INT_EN_RWT_EN 0x00008000 /* R/W */ > -#define INT_EN_RXE_EN 0x00004000 /* R/W */ > -#define INT_EN_TXE_EN 0x00002000 /* R/W */ > -//#define INT_EN_ERX_EN 0x00001000 /* R/W */ > -#define INT_EN_TDFU_EN 0x00000800 /* R/W */ > -#define INT_EN_TDFO_EN 0x00000400 /* R/W */ > -#define INT_EN_TDFA_EN 0x00000200 /* R/W */ > -#define INT_EN_TSFF_EN 0x00000100 /* R/W */ > -#define INT_EN_TSFL_EN 0x00000080 /* R/W */ > -//#define INT_EN_RXDF_EN 0x00000040 /* R/W */ > -#define INT_EN_RDFO_EN 0x00000040 /* R/W */ > -#define INT_EN_RDFL_EN 0x00000020 /* R/W */ > -#define INT_EN_RSFF_EN 0x00000010 /* R/W */ > -#define INT_EN_RSFL_EN 0x00000008 /* R/W */ > -#define INT_EN_GPIO2_INT 0x00000004 /* R/W */ > -#define INT_EN_GPIO1_INT 0x00000002 /* R/W */ > -#define INT_EN_GPIO0_INT 0x00000001 /* R/W */ > - > -#define BYTE_TEST (0x64 << AS) > -#define FIFO_INT (0x68 << AS) > -#define FIFO_INT_TX_AVAIL_LEVEL 0xFF000000 /* R/W */ > -#define FIFO_INT_TX_STS_LEVEL 0x00FF0000 /* R/W */ > -#define FIFO_INT_RX_AVAIL_LEVEL 0x0000FF00 /* R/W */ > -#define FIFO_INT_RX_STS_LEVEL 0x000000FF /* R/W */ > - > -#define RX_CFG (0x6C << AS) > -#define RX_CFG_RX_END_ALGN 0xC0000000 /* R/W */ > -#define RX_CFG_RX_END_ALGN4 0x00000000 /* R/W */ > -#define RX_CFG_RX_END_ALGN16 0x40000000 /* R/W */ > -#define RX_CFG_RX_END_ALGN32 0x80000000 /* R/W */ > -#define RX_CFG_RX_DMA_CNT 0x0FFF0000 /* R/W */ > -#define RX_CFG_RX_DUMP 0x00008000 /* R/W */ > -#define RX_CFG_RXDOFF 0x00001F00 /* R/W */ > -//#define RX_CFG_RXBAD 0x00000001 /* R/W */ > - > -#define TX_CFG (0x70 << AS) > -//#define TX_CFG_TX_DMA_LVL 0xE0000000 /* R/W */ > -//#define TX_CFG_TX_DMA_CNT 0x0FFF0000 /* R/W Self Clearing */ > -#define TX_CFG_TXS_DUMP 0x00008000 /* Self Clearing */ > -#define TX_CFG_TXD_DUMP 0x00004000 /* Self Clearing */ > -#define TX_CFG_TXSAO 0x00000004 /* R/W */ > -#define TX_CFG_TX_ON 0x00000002 /* R/W */ > -#define TX_CFG_STOP_TX 0x00000001 /* Self Clearing */ > - > -#define HW_CFG (0x74 << AS) > -#define HW_CFG_TTM 0x00200000 /* R/W */ > -#define HW_CFG_SF 0x00100000 /* R/W */ > -#define HW_CFG_TX_FIF_SZ 0x000F0000 /* R/W */ > -#define HW_CFG_TR 0x00003000 /* R/W */ > -#define HW_CFG_PHY_CLK_SEL 0x00000060 /* R/W */ > -#define HW_CFG_PHY_CLK_SEL_INT_PHY 0x00000000 /* R/W */ > -#define HW_CFG_PHY_CLK_SEL_EXT_PHY 0x00000020 /* R/W */ > -#define HW_CFG_PHY_CLK_SEL_CLK_DIS 0x00000040 /* R/W */ > -#define HW_CFG_SMI_SEL 0x00000010 /* R/W */ > -#define HW_CFG_EXT_PHY_DET 0x00000008 /* RO */ > -#define HW_CFG_EXT_PHY_EN 0x00000004 /* R/W */ > -#define HW_CFG_32_16_BIT_MODE 0x00000004 /* RO */ > -#define HW_CFG_SRST_TO 0x00000002 /* RO */ > -#define HW_CFG_SRST 0x00000001 /* Self Clearing */ > - > -#define RX_DP_CTRL (0x78 << AS) > -#define RX_DP_CTRL_RX_FFWD 0x80000000 /* R/W */ > -#define RX_DP_CTRL_FFWD_BUSY 0x80000000 /* RO */ > - > -#define RX_FIFO_INF (0x7C << AS) > -#define RX_FIFO_INF_RXSUSED 0x00FF0000 /* RO */ > -#define RX_FIFO_INF_RXDUSED 0x0000FFFF /* RO */ > - > -#define TX_FIFO_INF (0x80 << AS) > -#define TX_FIFO_INF_TSUSED 0x00FF0000 /* RO */ > -#define TX_FIFO_INF_TDFREE 0x0000FFFF /* RO */ > - > -#define PMT_CTRL (0x84 << AS) > -#define PMT_CTRL_PM_MODE 0x00003000 /* Self Clearing */ > -#define PMT_CTRL_PHY_RST 0x00000400 /* Self Clearing */ > -#define PMT_CTRL_WOL_EN 0x00000200 /* R/W */ > -#define PMT_CTRL_ED_EN 0x00000100 /* R/W */ > -#define PMT_CTRL_PME_TYPE 0x00000040 /* R/W Not Affected by SW Reset */ > -#define PMT_CTRL_WUPS 0x00000030 /* R/WC */ > -#define PMT_CTRL_WUPS_NOWAKE 0x00000000 /* R/WC */ > -#define PMT_CTRL_WUPS_ED 0x00000010 /* R/WC */ > -#define PMT_CTRL_WUPS_WOL 0x00000020 /* R/WC */ > -#define PMT_CTRL_WUPS_MULTI 0x00000030 /* R/WC */ > -#define PMT_CTRL_PME_IND 0x00000008 /* R/W */ > -#define PMT_CTRL_PME_POL 0x00000004 /* R/W */ > -#define PMT_CTRL_PME_EN 0x00000002 /* R/W Not Affected by SW Reset */ > -#define PMT_CTRL_READY 0x00000001 /* RO */ > - > -#define GPIO_CFG (0x88 << AS) > -#define GPIO_CFG_LED3_EN 0x40000000 /* R/W */ > -#define GPIO_CFG_LED2_EN 0x20000000 /* R/W */ > -#define GPIO_CFG_LED1_EN 0x10000000 /* R/W */ > -#define GPIO_CFG_GPIO2_INT_POL 0x04000000 /* R/W */ > -#define GPIO_CFG_GPIO1_INT_POL 0x02000000 /* R/W */ > -#define GPIO_CFG_GPIO0_INT_POL 0x01000000 /* R/W */ > -#define GPIO_CFG_EEPR_EN 0x00700000 /* R/W */ > -#define GPIO_CFG_GPIOBUF2 0x00040000 /* R/W */ > -#define GPIO_CFG_GPIOBUF1 0x00020000 /* R/W */ > -#define GPIO_CFG_GPIOBUF0 0x00010000 /* R/W */ > -#define GPIO_CFG_GPIODIR2 0x00000400 /* R/W */ > -#define GPIO_CFG_GPIODIR1 0x00000200 /* R/W */ > -#define GPIO_CFG_GPIODIR0 0x00000100 /* R/W */ > -#define GPIO_CFG_GPIOD4 0x00000010 /* R/W */ > -#define GPIO_CFG_GPIOD3 0x00000008 /* R/W */ > -#define GPIO_CFG_GPIOD2 0x00000004 /* R/W */ > -#define GPIO_CFG_GPIOD1 0x00000002 /* R/W */ > -#define GPIO_CFG_GPIOD0 0x00000001 /* R/W */ > - > -#define GPT_CFG (0x8C << AS) > -#define GPT_CFG_TIMER_EN 0x20000000 /* R/W */ > -#define GPT_CFG_GPT_LOAD 0x0000FFFF /* R/W */ > - > -#define GPT_CNT (0x90 << AS) > -#define GPT_CNT_GPT_CNT 0x0000FFFF /* RO */ > - > -#define ENDIAN (0x98 << AS) > -#define FREE_RUN (0x9C << AS) > -#define RX_DROP (0xA0 << AS) > -#define MAC_CSR_CMD (0xA4 << AS) > -#define MAC_CSR_CMD_CSR_BUSY 0x80000000 /* Self Clearing */ > -#define MAC_CSR_CMD_R_NOT_W 0x40000000 /* R/W */ > -#define MAC_CSR_CMD_CSR_ADDR 0x000000FF /* R/W */ > - > -#define MAC_CSR_DATA (0xA8 << AS) > -#define AFC_CFG (0xAC << AS) > -#define AFC_CFG_AFC_HI 0x00FF0000 /* R/W */ > -#define AFC_CFG_AFC_LO 0x0000FF00 /* R/W */ > -#define AFC_CFG_BACK_DUR 0x000000F0 /* R/W */ > -#define AFC_CFG_FCMULT 0x00000008 /* R/W */ > -#define AFC_CFG_FCBRD 0x00000004 /* R/W */ > -#define AFC_CFG_FCADD 0x00000002 /* R/W */ > -#define AFC_CFG_FCANY 0x00000001 /* R/W */ > - > -#define E2P_CMD (0xB0 << AS) > -#define E2P_CMD_EPC_BUSY 0x80000000 /* Self Clearing */ > -#define E2P_CMD_EPC_CMD 0x70000000 /* R/W */ > -#define E2P_CMD_EPC_CMD_READ 0x00000000 /* R/W */ > -#define E2P_CMD_EPC_CMD_EWDS 0x10000000 /* R/W */ > -#define E2P_CMD_EPC_CMD_EWEN 0x20000000 /* R/W */ > -#define E2P_CMD_EPC_CMD_WRITE 0x30000000 /* R/W */ > -#define E2P_CMD_EPC_CMD_WRAL 0x40000000 /* R/W */ > -#define E2P_CMD_EPC_CMD_ERASE 0x50000000 /* R/W */ > -#define E2P_CMD_EPC_CMD_ERAL 0x60000000 /* R/W */ > -#define E2P_CMD_EPC_CMD_RELOAD 0x70000000 /* R/W */ > -#define E2P_CMD_EPC_TIMEOUT 0x00000200 /* RO */ > -#define E2P_CMD_MAC_ADDR_LOADED 0x00000100 /* RO */ > -#define E2P_CMD_EPC_ADDR 0x000000FF /* R/W */ > - > -#define E2P_DATA (0xB4 << AS) > -#define E2P_DATA_EEPROM_DATA 0x000000FF /* R/W */ > -/* end of LAN register offsets and bit definitions */ > - > -/* MAC Control and Status registers */ > -#define MAC_CR 0x01 /* R/W */ > - > -/* MAC_CR - MAC Control Register */ > -#define MAC_CR_RXALL 0x80000000 > -// TODO: delete this bit? It is not described in the data sheet. > -#define MAC_CR_HBDIS 0x10000000 > -#define MAC_CR_RCVOWN 0x00800000 > -#define MAC_CR_LOOPBK 0x00200000 > -#define MAC_CR_FDPX 0x00100000 > -#define MAC_CR_MCPAS 0x00080000 > -#define MAC_CR_PRMS 0x00040000 > -#define MAC_CR_INVFILT 0x00020000 > -#define MAC_CR_PASSBAD 0x00010000 > -#define MAC_CR_HFILT 0x00008000 > -#define MAC_CR_HPFILT 0x00002000 > -#define MAC_CR_LCOLL 0x00001000 > -#define MAC_CR_BCAST 0x00000800 > -#define MAC_CR_DISRTY 0x00000400 > -#define MAC_CR_PADSTR 0x00000100 > -#define MAC_CR_BOLMT_MASK 0x000000C0 > -#define MAC_CR_DFCHK 0x00000020 > -#define MAC_CR_TXEN 0x00000008 > -#define MAC_CR_RXEN 0x00000004 > - > -#define ADDRH 0x02 /* R/W mask 0x0000FFFFUL */ > -#define ADDRL 0x03 /* R/W mask 0xFFFFFFFFUL */ > -#define HASHH 0x04 /* R/W */ > -#define HASHL 0x05 /* R/W */ > - > -#define MII_ACC 0x06 /* R/W */ > -#define MII_ACC_PHY_ADDR 0x0000F800 > -#define MII_ACC_MIIRINDA 0x000007C0 > -#define MII_ACC_MII_WRITE 0x00000002 > -#define MII_ACC_MII_BUSY 0x00000001 > - > -#define MII_DATA 0x07 /* R/W mask 0x0000FFFFUL */ > - > -#ifdef FLOW > -#undef FLOW /* clashed with include/asm/cpu/defBF561.h:1654 */ > -#endif > - > -#define FLOW 0x08 /* R/W */ > -#define FLOW_FCPT 0xFFFF0000 > -#define FLOW_FCPASS 0x00000004 > -#define FLOW_FCEN 0x00000002 > -#define FLOW_FCBSY 0x00000001 > - > -#define VLAN1 0x09 /* R/W mask 0x0000FFFFUL */ > -#define VLAN1_VTI1 0x0000ffff > - > -#define VLAN2 0x0A /* R/W mask 0x0000FFFFUL */ > -#define VLAN2_VTI2 0x0000ffff > - > -#define WUFF 0x0B /* WO */ > - > -#define WUCSR 0x0C /* R/W */ > -#define WUCSR_GUE 0x00000200 > -#define WUCSR_WUFR 0x00000040 > -#define WUCSR_MPR 0x00000020 > -#define WUCSR_WAKE_EN 0x00000004 > -#define WUCSR_MPEN 0x00000002 > - > -/* Chip ID values */ > -#define CHIP_9115 0x115 > -#define CHIP_9116 0x116 > -#define CHIP_9117 0x117 > -#define CHIP_9118 0x118 > -#define CHIP_9215 0x115a > -#define CHIP_9216 0x116a > -#define CHIP_9217 0x117a > -#define CHIP_9218 0x118a > -#define CHIP_9221 0x9221 > +#define AS CONFIG_DRIVER_NET_SMC911X_ADDRESS_SHIFT > +#include "smc911x.h" > > struct smc911x_priv { > struct eth_device edev; > diff --git a/drivers/net/smc911x.c b/drivers/net/smc911x.h > similarity index 60% > copy from drivers/net/smc911x.c > copy to drivers/net/smc911x.h > index 7dddbbc..68f6590 100644 > --- a/drivers/net/smc911x.c > +++ b/drivers/net/smc911x.h > @@ -22,24 +22,6 @@ > * MA 02111-1307 USA > */ > > -#ifdef CONFIG_ENABLE_DEVICE_NOISE > -# define DEBUG > -#endif > - > -#include <common.h> > - > -#include <command.h> > -#include <net.h> > -#include <miidev.h> > -#include <malloc.h> > -#include <init.h> > -#include <xfuncs.h> > -#include <errno.h> > -#include <clock.h> > -#include <io.h> > - > -#define AS CONFIG_DRIVER_NET_SMC911X_ADDRESS_SHIFT > - > /* Below are the register offsets and bit definitions > * of the Lan911x memory space > */ > @@ -367,392 +349,4 @@ > #define CHIP_9218 0x118a > #define CHIP_9221 0x9221 > > -struct smc911x_priv { > - struct eth_device edev; > - struct mii_device miidev; > - void __iomem *base; > -}; > - > -struct chip_id { > - u16 id; > - char *name; > -}; > - > -static const struct chip_id chip_ids[] = { > - { CHIP_9115, "LAN9115" }, > - { CHIP_9116, "LAN9116" }, > - { CHIP_9117, "LAN9117" }, > - { CHIP_9118, "LAN9118" }, > - { CHIP_9215, "LAN9215" }, > - { CHIP_9216, "LAN9216" }, > - { CHIP_9217, "LAN9217" }, > - { CHIP_9218, "LAN9218" }, > - { CHIP_9221, "LAN9221" }, > - { 0, NULL }, > -}; > - > -#define DRIVERNAME "smc911x" > - > -static int smc911x_mac_wait_busy(struct smc911x_priv *priv) > -{ > - uint64_t start = get_time_ns(); > - > - while (!is_timeout(start, MSECOND)) { > - if (!(readl(priv->base + MAC_CSR_CMD) & MAC_CSR_CMD_CSR_BUSY)) > - return 0; > - } > - > - printf("%s: mac timeout\n", __FUNCTION__); > - return -1; > -} > - > -static u32 smc911x_get_mac_csr(struct eth_device *edev, u8 reg) > -{ > - struct smc911x_priv *priv = edev->priv; > - ulong val; > - > - smc911x_mac_wait_busy(priv); > - > - writel(MAC_CSR_CMD_CSR_BUSY | MAC_CSR_CMD_R_NOT_W | reg, > - priv->base + MAC_CSR_CMD); > - > - smc911x_mac_wait_busy(priv); > - > - val = readl(priv->base + MAC_CSR_DATA); > - > - return val; > -} > - > -static void smc911x_set_mac_csr(struct eth_device *edev, u8 reg, u32 data) > -{ > - struct smc911x_priv *priv = edev->priv; > - > - smc911x_mac_wait_busy(priv); > - > - writel(data, priv->base + MAC_CSR_DATA); > - writel(MAC_CSR_CMD_CSR_BUSY | reg, priv->base + MAC_CSR_CMD); > - > - smc911x_mac_wait_busy(priv); > -} > - > -static int smc911x_get_ethaddr(struct eth_device *edev, unsigned char *m) > -{ > - unsigned long addrh, addrl; > - > - addrh = smc911x_get_mac_csr(edev, ADDRH); > - addrl = smc911x_get_mac_csr(edev, ADDRL); > - > - m[0] = (addrl ) & 0xff; > - m[1] = (addrl >> 8 ) & 0xff; > - m[2] = (addrl >> 16 ) & 0xff; > - m[3] = (addrl >> 24 ) & 0xff; > - m[4] = (addrh ) & 0xff; > - m[5] = (addrh >> 8 ) & 0xff; > - > - /* we get 0xff when there is no eeprom connected */ > - if ((m[0] & m[1] & m[2] & m[3] & m[4] & m[5]) == 0xff) > - return -1; > - > - return 0; > -} > - > -static int smc911x_set_ethaddr(struct eth_device *edev, unsigned char *m) > -{ > - unsigned long addrh, addrl; > - > - addrl = m[0] | m[1] << 8 | m[2] << 16 | m[3] << 24; > - addrh = m[4] | m[5] << 8; > - smc911x_set_mac_csr(edev, ADDRH, addrh); > - smc911x_set_mac_csr(edev, ADDRL, addrl); > - > - return 0; > -} > - > -static int smc911x_phy_read(struct mii_device *mdev, int phy_addr, int reg) > -{ > - struct eth_device *edev = mdev->edev; > - > - while (smc911x_get_mac_csr(edev, MII_ACC) & MII_ACC_MII_BUSY); > - > - smc911x_set_mac_csr(edev, MII_ACC, phy_addr << 11 | reg << 6 | > - MII_ACC_MII_BUSY); > - > - while (smc911x_get_mac_csr(edev, MII_ACC) & MII_ACC_MII_BUSY); > - > - return smc911x_get_mac_csr(edev, MII_DATA); > -} > - > -static int smc911x_phy_write(struct mii_device *mdev, int phy_addr, > - int reg, int val) > -{ > - struct eth_device *edev = mdev->edev; > - > - while (smc911x_get_mac_csr(edev, MII_ACC) & MII_ACC_MII_BUSY); > - > - smc911x_set_mac_csr(edev, MII_DATA, val); > - smc911x_set_mac_csr(edev, MII_ACC, > - phy_addr << 11 | reg << 6 | MII_ACC_MII_BUSY | > - MII_ACC_MII_WRITE); > - > - while (smc911x_get_mac_csr(edev, MII_ACC) & MII_ACC_MII_BUSY); > - > - return 0; > -} > - > -static int smc911x_phy_reset(struct eth_device *edev) > -{ > - struct smc911x_priv *priv = edev->priv; > - u32 reg; > - > - reg = readl(priv->base + PMT_CTRL); > - reg &= 0xfcf; > - reg |= PMT_CTRL_PHY_RST; > - writel(reg, priv->base + PMT_CTRL); > - > - mdelay(100); > - > - return 0; > -} > - > -static void smc911x_reset(struct eth_device *edev) > -{ > - struct smc911x_priv *priv = edev->priv; > - uint64_t start; > - > - /* Take out of PM setting first */ > - if (readl(priv->base + PMT_CTRL) & PMT_CTRL_READY) { > - /* Write to the bytetest will take out of powerdown */ > - writel(0, priv->base + BYTE_TEST); > - > - start = get_time_ns(); > - while(1) { > - if ((readl(priv->base + PMT_CTRL) & PMT_CTRL_READY)) > - break; > - if (is_timeout(start, 100 * USECOND)) { > - dev_err(&edev->dev, > - "timeout waiting for PM restore\n"); > - return; > - } > - } > - } > - > - /* Disable interrupts */ > - writel(0, priv->base + INT_EN); > - > - writel(HW_CFG_SRST, priv->base + HW_CFG); > - > - start = get_time_ns(); > - while(1) { > - if (!(readl(priv->base + E2P_CMD) & E2P_CMD_EPC_BUSY)) > - break; > - if (is_timeout(start, 10 * MSECOND)) { > - dev_err(&edev->dev, "reset timeout\n"); > - return; > - } > - } > - > - /* Reset the FIFO level and flow control settings */ > - smc911x_set_mac_csr(edev, FLOW, FLOW_FCPT | FLOW_FCEN); > - > - writel(0x0050287F, priv->base + AFC_CFG); > - > - /* Set to LED outputs */ > - writel(0x70070000, priv->base + GPIO_CFG); > -} > - > -static void smc911x_enable(struct eth_device *edev) > -{ > - struct smc911x_priv *priv = edev->priv; > - > - /* Enable TX */ > - writel(8 << 16 | HW_CFG_SF, priv->base + HW_CFG); > - > - writel(GPT_CFG_TIMER_EN | 10000, priv->base + GPT_CFG); > - > - writel(TX_CFG_TX_ON, priv->base + TX_CFG); > - > - /* no padding to start of packets */ > - writel(RX_CFG_RX_DUMP, priv->base + RX_CFG); > -} > - > -static int smc911x_eth_open(struct eth_device *edev) > -{ > - struct smc911x_priv *priv = (struct smc911x_priv *)edev->priv; > - > - miidev_wait_aneg(&priv->miidev); > - miidev_print_status(&priv->miidev); > - > - /* Turn on Tx + Rx */ > - smc911x_enable(edev); > - return 0; > -} > - > -static int smc911x_eth_send(struct eth_device *edev, void *packet, int length) > -{ > - struct smc911x_priv *priv = (struct smc911x_priv *)edev->priv; > - u32 *data = (u32*)packet; > - u32 tmplen; > - u32 status; > - uint64_t start; > - > - writel(TX_CMD_A_INT_FIRST_SEG | TX_CMD_A_INT_LAST_SEG | length, > - priv->base + TX_DATA_FIFO); > - writel(length, priv->base + TX_DATA_FIFO); > - > - tmplen = (length + 3) / 4; > - > - while(tmplen--) > - writel(*data++, priv->base + TX_DATA_FIFO); > - > - /* wait for transmission */ > - start = get_time_ns(); > - while (1) { > - if ((readl(priv->base + TX_FIFO_INF) & > - TX_FIFO_INF_TSUSED) >> 16) > - break; > - if (is_timeout(start, 100 * MSECOND)) { > - dev_err(&edev->dev, "TX timeout\n"); > - return -1; > - } > - } > - > - /* get status. Ignore 'no carrier' error, it has no meaning for > - * full duplex operation > - */ > - status = readl(priv->base + TX_STATUS_FIFO) & (TX_STS_LOC | > - TX_STS_LATE_COLL | TX_STS_MANY_COLL | TX_STS_MANY_DEFER | > - TX_STS_UNDERRUN); > - > - if(!status) > - return 0; > - > - dev_err(&edev->dev, "failed to send packet: %s%s%s%s%s\n", > - status & TX_STS_LOC ? "TX_STS_LOC " : "", > - status & TX_STS_LATE_COLL ? "TX_STS_LATE_COLL " : "", > - status & TX_STS_MANY_COLL ? "TX_STS_MANY_COLL " : "", > - status & TX_STS_MANY_DEFER ? "TX_STS_MANY_DEFER " : "", > - status & TX_STS_UNDERRUN ? "TX_STS_UNDERRUN" : ""); > - > - return -1; > -} > - > -static void smc911x_eth_halt(struct eth_device *edev) > -{ > - struct smc911x_priv *priv = (struct smc911x_priv *)edev->priv; > - > - /* Disable TX */ > - writel(TX_CFG_STOP_TX, priv->base + TX_CFG); > - > -// smc911x_reset(edev); > -} > - > -static int smc911x_eth_rx(struct eth_device *edev) > -{ > - struct smc911x_priv *priv = (struct smc911x_priv *)edev->priv; > - u32 *data = (u32 *)NetRxPackets[0]; > - u32 pktlen, tmplen; > - u32 status; > - > - if((readl(priv->base + RX_FIFO_INF) & RX_FIFO_INF_RXSUSED) >> 16) { > - status = readl(priv->base + RX_STATUS_FIFO); > - pktlen = (status & RX_STS_PKT_LEN) >> 16; > - > - writel(0, priv->base + RX_CFG); > - > - tmplen = (pktlen + 2 + 3) / 4; > - while(tmplen--) > - *data++ = readl(priv->base + RX_DATA_FIFO); > - > - if(status & RX_STS_ES) > - dev_err(&edev->dev, "dropped bad packet. Status: 0x%08x\n", > - status); > - else > - net_receive(NetRxPackets[0], pktlen); > - } > - > - return 0; > -} > - > -static int smc911x_init_dev(struct eth_device *edev) > -{ > - struct smc911x_priv *priv = (struct smc911x_priv *)edev->priv; > - > - smc911x_set_mac_csr(edev, MAC_CR, MAC_CR_TXEN | MAC_CR_RXEN | > - MAC_CR_HBDIS); > - > - miidev_restart_aneg(&priv->miidev); > - > - return 0; > -} > - > -static int smc911x_probe(struct device_d *dev) > -{ > - struct eth_device *edev; > - struct smc911x_priv *priv; > - uint32_t val; > - int i; > - void __iomem *base; > - > - base = dev_request_mem_region(dev, 0); > - > - val = readl(base + BYTE_TEST); > - if(val != 0x87654321) { > - dev_err(dev, "no smc911x found on 0x%p (byte_test=0x%08x)\n", > - base, val); > - return -ENODEV; > - } > - > - val = readl(base + ID_REV) >> 16; > - for(i = 0; chip_ids[i].id != 0; i++) { > - if (chip_ids[i].id == val) break; > - } > - if (!chip_ids[i].id) { > - dev_err(dev, "Unknown chip ID %04x\n", val); > - return -ENODEV; > - } > - > - dev_info(dev, "detected %s controller\n", chip_ids[i].name); > - > - priv = xzalloc(sizeof(*priv)); > - edev = &priv->edev; > - edev->priv = priv; > - > - edev->init = smc911x_init_dev; > - edev->open = smc911x_eth_open; > - edev->send = smc911x_eth_send; > - edev->recv = smc911x_eth_rx; > - edev->halt = smc911x_eth_halt; > - edev->get_ethaddr = smc911x_get_ethaddr; > - edev->set_ethaddr = smc911x_set_ethaddr; > - edev->parent = dev; > - > - priv->miidev.read = smc911x_phy_read; > - priv->miidev.write = smc911x_phy_write; > - priv->miidev.address = 1; > - priv->miidev.flags = 0; > - priv->miidev.edev = edev; > - priv->miidev.parent = dev; > - priv->base = base; > - > - smc911x_reset(edev); > - smc911x_phy_reset(edev); > - > - mii_register(&priv->miidev); > - eth_register(edev); > - > - return 0; > -} > - > -static struct driver_d smc911x_driver = { > - .name = "smc911x", > - .probe = smc911x_probe, > -}; > - > -static int smc911x_init(void) > -{ > - register_driver(&smc911x_driver); > - return 0; > -} > - > -device_initcall(smc911x_init); > > -- > 1.7.10.4 > > > _______________________________________________ > barebox mailing list > barebox@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/barebox > -- Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH 1/7] smc911x: move register define to smc911x.h 2012-08-14 20:19 ` Sascha Hauer @ 2012-08-15 4:34 ` Jean-Christophe PLAGNIOL-VILLARD 0 siblings, 0 replies; 13+ messages in thread From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-08-15 4:34 UTC (permalink / raw) To: Sascha Hauer; +Cc: barebox On 22:19 Tue 14 Aug , Sascha Hauer wrote: > On Tue, Aug 14, 2012 at 07:32:14PM +0200, Jean-Christophe PLAGNIOL-VILLARD wrote: > > this make the driver more readable > > > > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> > > --- > > drivers/net/smc911x.c | 329 +-------------------------- > > drivers/net/{smc911x.c => smc911x.h} | 406 ---------------------------------- > > 2 files changed, 2 insertions(+), 733 deletions(-) > > copy drivers/net/{smc911x.c => smc911x.h} (60%) > > This is only churn. Please drop. I'm going to use the linux one and sync both of them in a second patch series with more improvement so this help Best Regards, J. _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 13+ messages in thread
end of thread, other threads:[~2012-09-03 7:49 UTC | newest] Thread overview: 13+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2012-09-01 8:47 [PATCH 0/7 v3] smsc911x: runtime configuration improvement Jean-Christophe PLAGNIOL-VILLARD 2012-09-01 8:52 ` [PATCH 1/7] smc911x: move register define to smc911x.h Jean-Christophe PLAGNIOL-VILLARD 2012-09-01 8:52 ` [PATCH 2/7] smc911x: introduce read/write ops Jean-Christophe PLAGNIOL-VILLARD 2012-09-01 8:52 ` [PATCH 3/7] smc911x: add 16bit bus width support Jean-Christophe PLAGNIOL-VILLARD 2012-09-01 8:52 ` [PATCH 4/7] smc911x: add support to pass the shift via platform data Jean-Christophe PLAGNIOL-VILLARD 2012-09-01 8:52 ` [PATCH 5/7] smc911x: improve detection handle Jean-Christophe PLAGNIOL-VILLARD 2012-09-01 8:52 ` [PATCH 6/7] smc911x: update chip detection Jean-Christophe PLAGNIOL-VILLARD 2012-09-01 8:52 ` [PATCH 7/7] smc911x: check if the device is ready before using it Jean-Christophe PLAGNIOL-VILLARD 2012-09-03 7:49 ` [PATCH 0/7 v3] smsc911x: runtime configuration improvement Sascha Hauer -- strict thread matches above, loose matches on Subject: below -- 2012-08-29 4:27 [PATCH 0/7 2] " Jean-Christophe PLAGNIOL-VILLARD 2012-08-29 5:06 ` [PATCH 1/7] smc911x: move register define to smc911x.h Jean-Christophe PLAGNIOL-VILLARD 2012-08-14 17:25 [PATCH 0/7] smsc911x: runtime configuration improvement Jean-Christophe PLAGNIOL-VILLARD 2012-08-14 17:32 ` [PATCH 1/7] smc911x: move register define to smc911x.h Jean-Christophe PLAGNIOL-VILLARD 2012-08-14 20:19 ` Sascha Hauer 2012-08-15 4:34 ` Jean-Christophe PLAGNIOL-VILLARD
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox