* [PATCH 1/4] ARM OMAP: remove SRAM stack
@ 2012-09-24 8:18 Jan Luebbe
2012-09-24 8:18 ` [PATCH 2/4] ARM OMAP3: rename arch_init_lowlevel to board_init_lowlevel Jan Luebbe
` (2 more replies)
0 siblings, 3 replies; 5+ messages in thread
From: Jan Luebbe @ 2012-09-24 8:18 UTC (permalink / raw)
To: barebox
From: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
arch/arm/mach-omap/include/mach/omap3-silicon.h | 2 --
arch/arm/mach-omap/include/mach/omap4-silicon.h | 2 --
arch/arm/mach-omap/omap3_core.S | 2 --
3 files changed, 6 deletions(-)
diff --git a/arch/arm/mach-omap/include/mach/omap3-silicon.h b/arch/arm/mach-omap/include/mach/omap3-silicon.h
index e4002e6..3581b60 100644
--- a/arch/arm/mach-omap/include/mach/omap3-silicon.h
+++ b/arch/arm/mach-omap/include/mach/omap3-silicon.h
@@ -110,8 +110,6 @@
#define OMAP_SRAM_BASE 0x40200000
#define OMAP_SRAM_INTVECT 0x4020F800
#define OMAP_SRAM_INTVECT_COPYSIZE 0x64
-/** Temporary stack for us to use C calls in low_level_init */
-#define OMAP_SRAM_STACK 0x4020FFFC
/** Gives the silicon revision */
#define OMAP_TAP_BASE (OMAP_L4_WKUP_BASE + 0xA000)
diff --git a/arch/arm/mach-omap/include/mach/omap4-silicon.h b/arch/arm/mach-omap/include/mach/omap4-silicon.h
index 4082bac..e6b31ed 100644
--- a/arch/arm/mach-omap/include/mach/omap4-silicon.h
+++ b/arch/arm/mach-omap/include/mach/omap4-silicon.h
@@ -147,8 +147,6 @@ struct s32ktimer {
#define NON_SECURE_SRAM_END 0x4030E000 /* Not inclusive */
/* base address for indirect vectors (internal boot mode) */
#define SRAM_ROM_VECT_BASE 0x4030D000
-/* Temporary SRAM stack used while low level init is done */
-#define LOW_LEVEL_SRAM_STACK NON_SECURE_SRAM_END
/*
* OMAP4 real hardware:
diff --git a/arch/arm/mach-omap/omap3_core.S b/arch/arm/mach-omap/omap3_core.S
index ceb3c76..6a9f44f 100644
--- a/arch/arm/mach-omap/omap3_core.S
+++ b/arch/arm/mach-omap/omap3_core.S
@@ -95,6 +95,4 @@ finished_inval:
mov pc, lr
ENDPROC(arch_init_lowlevel)
-SRAM_STACK:
- .word OMAP_SRAM_STACK
#endif /* CONFIG_ARCH_HAS_LOWLEVEL_INIT */
--
1.7.10.4
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH 2/4] ARM OMAP3: rename arch_init_lowlevel to board_init_lowlevel
2012-09-24 8:18 [PATCH 1/4] ARM OMAP: remove SRAM stack Jan Luebbe
@ 2012-09-24 8:18 ` Jan Luebbe
2012-09-24 8:18 ` [PATCH 3/4] ARM: remove ARCH_HAS_LOWLEVEL_INIT Jan Luebbe
2012-09-24 8:18 ` [PATCH 4/4] ARM: give boards control of the reset entry point Jan Luebbe
2 siblings, 0 replies; 5+ messages in thread
From: Jan Luebbe @ 2012-09-24 8:18 UTC (permalink / raw)
To: barebox
From: Sascha Hauer <s.hauer@pengutronix.de>
OMAP3 is the only architecture which has a arch_init_lowlevel in
which it invalidates the dcache. This can easily be done in
board_init_lowlevel aswell. Since on OMAP3 we are always executed
in SRAM we'll never need a board specific lowlevel_init. So the
easiest way of getting rid of this special handling is to just
rename the function.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
arch/arm/mach-omap/Kconfig | 1 -
arch/arm/mach-omap/omap3_core.S | 8 ++------
2 files changed, 2 insertions(+), 7 deletions(-)
diff --git a/arch/arm/mach-omap/Kconfig b/arch/arm/mach-omap/Kconfig
index d735284..9c76a96 100644
--- a/arch/arm/mach-omap/Kconfig
+++ b/arch/arm/mach-omap/Kconfig
@@ -37,7 +37,6 @@ config ARCH_OMAP3
select CPU_V7
select GENERIC_GPIO
select OMAP3_LOWLEVEL_INIT
- select ARCH_HAS_LOWLEVEL_INIT
select OMAP_CLOCK_SOURCE_S32K
help
Say Y here if you are using Texas Instrument's OMAP343x based platform
diff --git a/arch/arm/mach-omap/omap3_core.S b/arch/arm/mach-omap/omap3_core.S
index 6a9f44f..d1be6e5 100644
--- a/arch/arm/mach-omap/omap3_core.S
+++ b/arch/arm/mach-omap/omap3_core.S
@@ -12,7 +12,6 @@
* functions.
* @li Call architecture initialization function a_init
*
- * arch_init_lowlevel is enabled if CONFIG_ARCH_HAS_LOWLEVEL_INIT is defined
*/
/*
* (C) Copyright 2006-2008
@@ -42,8 +41,7 @@
#include <mach/wdt.h>
#include <mach/clocks.h>
-#ifdef CONFIG_ARCH_HAS_LOWLEVEL_INIT
-ENTRY(arch_init_lowlevel)
+ENTRY(board_init_lowlevel)
/* Invalidate all Dcaches */
#ifndef CONFIG_CPU_V7_DCACHE_SKIP
/* If Arch specific ROM code SMI handling does not exist */
@@ -93,6 +91,4 @@ finished_inval:
#endif /* CONFIG_CPU_V7_DCACHE_SKIP */
/* back to arch calling code */
mov pc, lr
-ENDPROC(arch_init_lowlevel)
-
-#endif /* CONFIG_ARCH_HAS_LOWLEVEL_INIT */
+ENDPROC(board_init_lowlevel)
--
1.7.10.4
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH 3/4] ARM: remove ARCH_HAS_LOWLEVEL_INIT
2012-09-24 8:18 [PATCH 1/4] ARM OMAP: remove SRAM stack Jan Luebbe
2012-09-24 8:18 ` [PATCH 2/4] ARM OMAP3: rename arch_init_lowlevel to board_init_lowlevel Jan Luebbe
@ 2012-09-24 8:18 ` Jan Luebbe
2012-09-24 8:18 ` [PATCH 4/4] ARM: give boards control of the reset entry point Jan Luebbe
2 siblings, 0 replies; 5+ messages in thread
From: Jan Luebbe @ 2012-09-24 8:18 UTC (permalink / raw)
To: barebox
From: Sascha Hauer <s.hauer@pengutronix.de>
This is unused now and not needed. We have a board_init_lowlevel. If a
board needs some architecture setup it can always call it from its
board_init_lowlevel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
arch/arm/cpu/start-reset.c | 4 ----
arch/arm/include/asm/barebox-arm.h | 1 -
common/Kconfig | 3 ---
3 files changed, 8 deletions(-)
diff --git a/arch/arm/cpu/start-reset.c b/arch/arm/cpu/start-reset.c
index e0df676..46193ef 100644
--- a/arch/arm/cpu/start-reset.c
+++ b/arch/arm/cpu/start-reset.c
@@ -40,10 +40,6 @@ void __naked __bare_init reset(void)
r |= 0xd3;
__asm__ __volatile__("msr cpsr, %0" : : "r"(r));
-#ifdef CONFIG_ARCH_HAS_LOWLEVEL_INIT
- arch_init_lowlevel();
-#endif
-
/* disable MMU stuff and caches */
r = get_cr();
r &= ~(CR_M | CR_C | CR_B | CR_S | CR_R | CR_V);
diff --git a/arch/arm/include/asm/barebox-arm.h b/arch/arm/include/asm/barebox-arm.h
index b880dd4..2689a04 100644
--- a/arch/arm/include/asm/barebox-arm.h
+++ b/arch/arm/include/asm/barebox-arm.h
@@ -41,6 +41,5 @@ extern char __ll_return[];
void board_init_lowlevel(void);
void board_init_lowlevel_return(void);
-void arch_init_lowlevel(void);
#endif /* _BAREBOX_ARM_H_ */
diff --git a/common/Kconfig b/common/Kconfig
index b97392c..bcc3581 100644
--- a/common/Kconfig
+++ b/common/Kconfig
@@ -292,9 +292,6 @@ config MACH_DO_LOWLEVEL_INIT
on many platforms. Disabling this option allows configurations to use
barebox as a second stage boot loader.
-config ARCH_HAS_LOWLEVEL_INIT
- bool
-
config PROMPT
string
prompt "barebox command prompt"
--
1.7.10.4
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH 4/4] ARM: give boards control of the reset entry point
2012-09-24 8:18 [PATCH 1/4] ARM OMAP: remove SRAM stack Jan Luebbe
2012-09-24 8:18 ` [PATCH 2/4] ARM OMAP3: rename arch_init_lowlevel to board_init_lowlevel Jan Luebbe
2012-09-24 8:18 ` [PATCH 3/4] ARM: remove ARCH_HAS_LOWLEVEL_INIT Jan Luebbe
@ 2012-09-24 8:18 ` Jan Luebbe
2012-09-25 11:28 ` Sascha Hauer
2 siblings, 1 reply; 5+ messages in thread
From: Jan Luebbe @ 2012-09-24 8:18 UTC (permalink / raw)
To: barebox
On some SoCs (for example AM35xx), the ROM bootloader passes useful
information in r0 when jumping to barebox.
To avoid overwriting this in the generic reset code, we introduce
common_reset as a C function and as an assembler macro. This is then
called form the reset entry point (either in common or in board code).
This patch is based on code by Sascha Hauer <s.hauer@pengutronix.de>.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
---
arch/arm/boards/a9m2410/lowlevel_init.S | 17 +++--
arch/arm/boards/a9m2440/lowlevel_init.S | 15 ++---
arch/arm/boards/at91sam9260ek/lowlevel_init.S | 9 ++-
arch/arm/boards/eukrea_cpuimx25/lowlevel.c | 5 +-
arch/arm/boards/eukrea_cpuimx27/lowlevel_init.S | 11 ++--
arch/arm/boards/eukrea_cpuimx35/lowlevel.c | 5 +-
.../boards/freescale-mx25-3-stack/lowlevel_init.S | 11 ++--
.../boards/freescale-mx35-3-stack/lowlevel_init.S | 12 ++--
.../boards/friendlyarm-mini2440/lowlevel_init.S | 18 +++---
arch/arm/boards/friendlyarm-tiny210/lowlevel.c | 5 +-
arch/arm/boards/guf-cupid/lowlevel.c | 7 +-
arch/arm/boards/guf-neso/lowlevel.c | 6 +-
arch/arm/boards/imx21ads/lowlevel_init.S | 12 ++--
arch/arm/boards/imx27ads/lowlevel_init.S | 11 ++--
arch/arm/boards/karo-tx25/lowlevel.c | 5 +-
arch/arm/boards/netx/platform.S | 9 ++-
arch/arm/boards/panda/lowlevel.c | 7 +-
arch/arm/boards/pcm027/lowlevel_init.S | 10 ++-
arch/arm/boards/pcm037/lowlevel_init.S | 12 ++--
arch/arm/boards/pcm038/lowlevel.c | 5 +-
arch/arm/boards/pcm043/lowlevel.c | 5 +-
arch/arm/boards/pcm049/lowlevel.c | 5 +-
arch/arm/boards/phycard-a-xl2/lowlevel.c | 5 +-
arch/arm/boards/phycard-i.MX27/lowlevel_init.S | 12 ++--
arch/arm/boards/scb9328/lowlevel_init.S | 11 ++--
arch/arm/cpu/Makefile | 4 +-
arch/arm/cpu/start-pbl.c | 12 ++++
arch/arm/cpu/start-reset.c | 63 ------------------
arch/arm/cpu/start.c | 12 ++++
arch/arm/include/asm/barebox-arm-head.h | 68 ++++++++++++++++++++
arch/arm/include/asm/system.h | 4 ++
arch/arm/mach-at91/at91rm9200_lowlevel_init.c | 5 +-
arch/arm/mach-at91/at91sam926x_lowlevel_init.c | 5 +-
arch/arm/mach-ep93xx/lowlevel_init.S | 15 ++---
arch/arm/mach-omap/Kconfig | 5 +-
arch/arm/mach-omap/omap3_core.S | 9 ++-
36 files changed, 257 insertions(+), 175 deletions(-)
delete mode 100644 arch/arm/cpu/start-reset.c
diff --git a/arch/arm/boards/a9m2410/lowlevel_init.S b/arch/arm/boards/a9m2410/lowlevel_init.S
index 0463b26..502ecdd 100644
--- a/arch/arm/boards/a9m2410/lowlevel_init.S
+++ b/arch/arm/boards/a9m2410/lowlevel_init.S
@@ -4,13 +4,14 @@
#include <config.h>
#include <mach/s3c-iomap.h>
+#include <asm/barebox-arm-head.h>
- .section ".text_bare_init.board_init_lowlevel","ax"
+ .section ".text_bare_init.reset","ax"
-.globl board_init_lowlevel
-board_init_lowlevel:
+.globl reset
+reset:
- mov r10, lr /* save the link register */
+ common_reset r0
bl s3c24x0_disable_wd
@@ -20,7 +21,7 @@ board_init_lowlevel:
cmp pc, #S3C_SDRAM_END
bhs 1f
- mov pc, r10
+ b board_init_lowlevel_return
/* we are running from NOR or NAND/SRAM memory. Do further initialisation */
1:
@@ -29,9 +30,7 @@ board_init_lowlevel:
bl s3c24x0_sdram_init
#ifdef CONFIG_S3C_NAND_BOOT
- mov lr, r10 /* restore the link register */
/* up to here we are running from the internal SRAM area */
- b s3c24x0_nand_boot /* does return directly to our caller into SDRAM */
-#else
- mov pc, r10
+ bl s3c24x0_nand_boot
#endif
+ b board_init_lowlevel_return
diff --git a/arch/arm/boards/a9m2440/lowlevel_init.S b/arch/arm/boards/a9m2440/lowlevel_init.S
index 305014c..da29efd 100644
--- a/arch/arm/boards/a9m2440/lowlevel_init.S
+++ b/arch/arm/boards/a9m2440/lowlevel_init.S
@@ -5,8 +5,9 @@
#include <config.h>
#include <mach/s3c-iomap.h>
#include <mach/s3c24xx-gpio.h>
+#include <asm/barebox-arm-head.h>
- .section ".text_bare_init.board_init_lowlevel","ax"
+ .section ".text_bare_init.reset","ax"
/*
* To be able to setup the SDRAM interface correctly, we need some
@@ -211,10 +212,10 @@ SDRAMDATA:
/* ------------------------------------------------------------------------ */
-.globl board_init_lowlevel
-board_init_lowlevel:
+.globl reset
+reset:
- mov r10, lr /* save the link register */
+ common_reset r0
bl s3c24x0_disable_wd
@@ -233,9 +234,7 @@ board_init_lowlevel:
bl sdram_init
#ifdef CONFIG_S3C_NAND_BOOT
- mov lr, r10 /* restore the link register */
/* up to here we are running from the internal SRAM area */
- b s3c24x0_nand_boot /* does return directly to our caller into SDRAM */
-#else
- mov pc, r10
+ bl s3c24x0_nand_boot
#endif
+ b board_init_lowlevel_return
diff --git a/arch/arm/boards/at91sam9260ek/lowlevel_init.S b/arch/arm/boards/at91sam9260ek/lowlevel_init.S
index 4961682..7d51b7b 100644
--- a/arch/arm/boards/at91sam9260ek/lowlevel_init.S
+++ b/arch/arm/boards/at91sam9260ek/lowlevel_init.S
@@ -21,6 +21,9 @@
* MA 02111-1307 USA
*/
-.globl board_init_lowlevel
-board_init_lowlevel:
- mov pc, lr
+#include <asm/barebox-arm-head.h>
+
+.globl reset
+reset:
+ common_reset r0
+ b board_init_lowlevel_return
diff --git a/arch/arm/boards/eukrea_cpuimx25/lowlevel.c b/arch/arm/boards/eukrea_cpuimx25/lowlevel.c
index 89066e9..ca94ac5 100644
--- a/arch/arm/boards/eukrea_cpuimx25/lowlevel.c
+++ b/arch/arm/boards/eukrea_cpuimx25/lowlevel.c
@@ -29,6 +29,7 @@
#include <io.h>
#include <mach/imx-nand.h>
#include <asm/barebox-arm.h>
+#include <asm/barebox-arm-head.h>
#include <asm-generic/sections.h>
#include <asm-generic/memory_layout.h>
#include <asm/system.h>
@@ -48,7 +49,7 @@ static void __bare_init __naked insdram(void)
}
#endif
-void __bare_init __naked board_init_lowlevel(void)
+void __bare_init __naked reset(void)
{
uint32_t r;
#ifdef CONFIG_NAND_IMX_BOOT
@@ -57,6 +58,8 @@ void __bare_init __naked board_init_lowlevel(void)
#endif
register uint32_t loops = 0x20000;
+ common_reset();
+
/* restart the MPLL and wait until it's stable */
writel(readl(IMX_CCM_BASE + CCM_CCTL) | (1 << 27),
IMX_CCM_BASE + CCM_CCTL);
diff --git a/arch/arm/boards/eukrea_cpuimx27/lowlevel_init.S b/arch/arm/boards/eukrea_cpuimx27/lowlevel_init.S
index 0dae3ec..af4deeb 100644
--- a/arch/arm/boards/eukrea_cpuimx27/lowlevel_init.S
+++ b/arch/arm/boards/eukrea_cpuimx27/lowlevel_init.S
@@ -1,6 +1,7 @@
#include <config.h>
#include <asm-generic/memory_layout.h>
#include <mach/imx-regs.h>
+#include <asm/barebox-arm-head.h>
#define writel(val, reg) \
ldr r0, =reg; \
@@ -60,10 +61,10 @@
.section ".text_bare_init","ax"
-.globl board_init_lowlevel
-board_init_lowlevel:
+.globl reset
+reset:
- mov r10, lr
+ common_reset r0
/* ahb lite ip interface */
writel(0x20040304, AIPI1_PSR0)
@@ -103,7 +104,7 @@ board_init_lowlevel:
cmp pc, #0xc0000000
bhi 1f
- mov pc,r10
+ b board_init_lowlevel_return
1:
sdram_init
@@ -135,4 +136,4 @@ copy_loop:
#endif /* CONFIG_NAND_IMX_BOOT */
ret:
- mov pc,r10
+ b board_init_lowlevel_return
diff --git a/arch/arm/boards/eukrea_cpuimx35/lowlevel.c b/arch/arm/boards/eukrea_cpuimx35/lowlevel.c
index 57867dc..b8dec71 100644
--- a/arch/arm/boards/eukrea_cpuimx35/lowlevel.c
+++ b/arch/arm/boards/eukrea_cpuimx35/lowlevel.c
@@ -29,6 +29,7 @@
#include <io.h>
#include <mach/imx-nand.h>
#include <asm/barebox-arm.h>
+#include <asm/barebox-arm-head.h>
#include <asm-generic/sections.h>
#include <asm-generic/memory_layout.h>
#include <asm/system.h>
@@ -59,7 +60,7 @@ static void __bare_init __naked insdram(void)
}
#endif
-void __bare_init __naked board_init_lowlevel(void)
+void __bare_init __naked reset(void)
{
uint32_t r, s;
unsigned long ccm_base = IMX_CCM_BASE;
@@ -69,6 +70,8 @@ void __bare_init __naked board_init_lowlevel(void)
#endif
register uint32_t loops = 0x20000;
+ common_reset();
+
r = get_cr();
r |= CR_Z; /* Flow prediction (Z) */
r |= CR_U; /* unaligned accesses */
diff --git a/arch/arm/boards/freescale-mx25-3-stack/lowlevel_init.S b/arch/arm/boards/freescale-mx25-3-stack/lowlevel_init.S
index fa0f957..6157949 100644
--- a/arch/arm/boards/freescale-mx25-3-stack/lowlevel_init.S
+++ b/arch/arm/boards/freescale-mx25-3-stack/lowlevel_init.S
@@ -25,6 +25,7 @@
#include <mach/imx-regs.h>
#include <mach/imx-pll.h>
#include <mach/esdctl.h>
+#include <asm/barebox-arm-head.h>
#define writel(val, reg) \
ldr r0, =reg; \
@@ -52,9 +53,9 @@ MPCTL_PARAM_532_W: .word MPCTL_PARAM_532
PPCTL_PARAM_W: .word PPCTL_PARAM_300
CCM_BASE_ADDR_W: .word IMX_CCM_BASE
-.globl board_init_lowlevel
-board_init_lowlevel:
- mov r10, lr
+.globl reset
+reset:
+ common_reset r0
#define MX25_CCM_MCR 0x64
@@ -80,7 +81,7 @@ board_init_lowlevel:
cmp pc, #0x90000000
bhi 1f
- mov pc, lr
+ b board_init_lowlevel_return
1:
ldr r0, ESDCTL_BASE_W
@@ -128,7 +129,7 @@ copy_loop:
#endif /* CONFIG_NAND_IMX_BOOT */
ret:
- mov pc, r10
+ b board_init_lowlevel_return
/*
* r0: control base, r1: ram bank base
diff --git a/arch/arm/boards/freescale-mx35-3-stack/lowlevel_init.S b/arch/arm/boards/freescale-mx35-3-stack/lowlevel_init.S
index 837d2ff..a5e8c19 100644
--- a/arch/arm/boards/freescale-mx35-3-stack/lowlevel_init.S
+++ b/arch/arm/boards/freescale-mx35-3-stack/lowlevel_init.S
@@ -26,6 +26,8 @@
#include <mach/esdctl.h>
#include <asm/cache-l2x0.h>
#include <asm-generic/memory_layout.h>
+#include <asm/barebox-arm-head.h>
+
#include "board-mx35_3stack.h"
#define CSD0_BASE_ADDR 0x80000000
@@ -58,9 +60,9 @@ MPCTL_PARAM_532_W: .word MPCTL_PARAM_532
PPCTL_PARAM_W: .word PPCTL_PARAM_300
CCM_BASE_ADDR_W: .word IMX_CCM_BASE
-.globl board_init_lowlevel
-board_init_lowlevel:
- mov r10, lr
+.globl reset
+reset:
+ common_reset r0
mrc 15, 0, r1, c1, c0, 0
@@ -128,7 +130,7 @@ board_init_lowlevel:
cmp pc, #CSD1_BASE_ADDR
bhi 1f
- mov pc, r10
+ b board_init_lowlevel_return
1:
ldr r0, =ESDCTL_BASE_ADDR
@@ -183,7 +185,7 @@ copy_loop:
ret:
#endif /* CONFIG_NAND_IMX_BOOT */
- mov pc, r10
+ b board_init_lowlevel_return
/*
* r0: ESDCTL control base, r1: sdram slot base
diff --git a/arch/arm/boards/friendlyarm-mini2440/lowlevel_init.S b/arch/arm/boards/friendlyarm-mini2440/lowlevel_init.S
index 827cf00..5c06b1c 100644
--- a/arch/arm/boards/friendlyarm-mini2440/lowlevel_init.S
+++ b/arch/arm/boards/friendlyarm-mini2440/lowlevel_init.S
@@ -4,15 +4,15 @@
#include <config.h>
#include <mach/s3c-iomap.h>
+#include <asm/barebox-arm-head.h>
- .section ".text_bare_init.board_init_lowlevel","ax"
+ .section ".text_bare_init.reset","ax"
/* ------------------------------------------------------------------------ */
-.globl board_init_lowlevel
-board_init_lowlevel:
-
- mov r10, lr /* save the link register */
+.globl reset
+reset:
+ common_reset r0
bl s3c24x0_disable_wd
@@ -22,7 +22,7 @@ board_init_lowlevel:
cmp pc, #S3C_SDRAM_END
bhs 1f
- mov pc, r10
+ b board_init_lowlevel_return
/* we are running from NOR or NAND/SRAM memory. Do further initialisation */
1:
@@ -31,9 +31,7 @@ board_init_lowlevel:
bl s3c24x0_sdram_init
#ifdef CONFIG_S3C_NAND_BOOT
- mov lr, r10 /* restore the link register */
/* up to here we are running from the internal SRAM area */
- b s3c24x0_nand_boot /* does return directly to our caller into SDRAM */
-#else
- mov pc, r10
+ bl s3c24x0_nand_boot
#endif
+ b board_init_lowlevel_return
diff --git a/arch/arm/boards/friendlyarm-tiny210/lowlevel.c b/arch/arm/boards/friendlyarm-tiny210/lowlevel.c
index 19739d8..791918a 100644
--- a/arch/arm/boards/friendlyarm-tiny210/lowlevel.c
+++ b/arch/arm/boards/friendlyarm-tiny210/lowlevel.c
@@ -24,6 +24,7 @@
#include <init.h>
#include <io.h>
#include <asm/barebox-arm.h>
+#include <asm/barebox-arm-head.h>
#include <asm/sections.h>
#include <mach/s3c-iomap.h>
#include <mach/s3c-clocks.h>
@@ -49,10 +50,12 @@ int __bare_init s5p_irom_load_mmc(void *dest, uint32_t start_block, uint16_t blo
}
-void __bare_init board_init_lowlevel(void)
+void __bare_init reset(void)
{
uint32_t r;
+ common_reset();
+
#ifdef CONFIG_S3C_PLL_INIT
s5p_init_pll();
#endif
diff --git a/arch/arm/boards/guf-cupid/lowlevel.c b/arch/arm/boards/guf-cupid/lowlevel.c
index 8fa9152..d50090b 100644
--- a/arch/arm/boards/guf-cupid/lowlevel.c
+++ b/arch/arm/boards/guf-cupid/lowlevel.c
@@ -29,6 +29,7 @@
#include <io.h>
#include <mach/imx-nand.h>
#include <asm/barebox-arm.h>
+#include <asm/barebox-arm-head.h>
#include <asm-generic/sections.h>
#include <asm-generic/memory_layout.h>
#include <asm/system.h>
@@ -182,7 +183,7 @@ static void __bare_init noinline setup_sdram(u32 memsize, u32 mode, u32 sdram_ad
#define UNALIGNED_ACCESS_ENABLE
#define LOW_INT_LATENCY_ENABLE
-void __bare_init __naked board_init_lowlevel(void)
+void __bare_init __naked reset(void)
{
u32 r0, r1;
void *iomuxc_base = (void *)IMX_IOMUXC_BASE;
@@ -191,8 +192,10 @@ void __bare_init __naked board_init_lowlevel(void)
unsigned int *trg, *src;
#endif
+ common_reset();
+
r0 = 0x10000000 + 128 * 1024 - 16;
- __asm__ __volatile__("mov sp, %0" : : "r"(r0));
+ __asm__ __volatile__("mov sp, %0" : : "r"(r0));
/*
* ARM1136 init
diff --git a/arch/arm/boards/guf-neso/lowlevel.c b/arch/arm/boards/guf-neso/lowlevel.c
index 9b206be..5bb2d21 100644
--- a/arch/arm/boards/guf-neso/lowlevel.c
+++ b/arch/arm/boards/guf-neso/lowlevel.c
@@ -29,6 +29,7 @@
#include <io.h>
#include <mach/imx-nand.h>
#include <asm/barebox-arm.h>
+#include <asm/barebox-arm-head.h>
#include <asm/system.h>
#include <asm-generic/sections.h>
#include <asm-generic/memory_layout.h>
@@ -52,13 +53,16 @@ static void __bare_init __naked insdram(void)
#define ESDCTL0_VAL (ESDCTL0_SDE | ESDCTL0_ROW13 | ESDCTL0_COL10)
-void __bare_init __naked board_init_lowlevel(void)
+void __bare_init __naked reset(void)
{
uint32_t r;
int i;
#ifdef CONFIG_NAND_IMX_BOOT
unsigned int *trg, *src;
#endif
+
+ common_reset();
+
/* ahb lite ip interface */
AIPI1_PSR0 = 0x20040304;
AIPI1_PSR1 = 0xDFFBFCFB;
diff --git a/arch/arm/boards/imx21ads/lowlevel_init.S b/arch/arm/boards/imx21ads/lowlevel_init.S
index 1aeea57..1568f3c 100644
--- a/arch/arm/boards/imx21ads/lowlevel_init.S
+++ b/arch/arm/boards/imx21ads/lowlevel_init.S
@@ -20,14 +20,14 @@
#include <config.h>
#include <asm-generic/memory_layout.h>
#include <mach/imx-regs.h>
+#include <asm/barebox-arm-head.h>
.section ".text_bare_init","ax"
-.globl board_init_lowlevel
-board_init_lowlevel:
+.globl reset
+reset:
-/* Save lr, because it is overwritten by the calls to mem_delay. */
- mov r10, lr
+ common_reset r0
/*
* Initialize the AHB-Lite IP Interface (AIPI) module (to enable access to
@@ -79,7 +79,7 @@ board_init_lowlevel:
cmp pc, #0xc8000000
bhi 1f
- mov pc, r10
+ b board_init_lowlevel_return
1:
/* Precharge */
@@ -149,7 +149,7 @@ copy_loop:
#endif /* CONFIG_NAND_IMX_BOOT */
ret:
- mov pc, r10
+ b board_init_lowlevel_return
/*
* spin for a while. we need to wait at least 200 usecs.
diff --git a/arch/arm/boards/imx27ads/lowlevel_init.S b/arch/arm/boards/imx27ads/lowlevel_init.S
index df12aea..1bebb1d 100644
--- a/arch/arm/boards/imx27ads/lowlevel_init.S
+++ b/arch/arm/boards/imx27ads/lowlevel_init.S
@@ -6,6 +6,7 @@
#include <config.h>
#include <mach/imx-regs.h>
+#include <asm/barebox-arm-head.h>
#define writel(val, reg) \
ldr r0, =reg; \
@@ -111,10 +112,10 @@ NORMAL_MODE .long 0x00000000 // system/external device dependent data (SMODE=00
writel(0x0000000c, 0xD8001010)
.endm
-.globl board_init_lowlevel
-board_init_lowlevel:
+.globl reset
+reset:
- mov r10, lr
+ common_reset r0
/* ahb lite ip interface */
writel(0x20040304, AIPI1_PSR0)
@@ -164,9 +165,9 @@ board_init_lowlevel:
cmp pc, #0xc0000000
bhi 1f
- mov pc,r10
+ b board_init_lowlevel_return
1:
sdram_init_sha
- mov pc,r10
+ b board_init_lowlevel_return
diff --git a/arch/arm/boards/karo-tx25/lowlevel.c b/arch/arm/boards/karo-tx25/lowlevel.c
index 9f1c5d6..f06cc7c 100644
--- a/arch/arm/boards/karo-tx25/lowlevel.c
+++ b/arch/arm/boards/karo-tx25/lowlevel.c
@@ -27,6 +27,7 @@
#include <io.h>
#include <mach/imx-nand.h>
#include <asm/barebox-arm.h>
+#include <asm/barebox-arm-head.h>
#include <asm/system.h>
#include <asm-generic/sections.h>
#include <asm-generic/memory_layout.h>
@@ -70,13 +71,15 @@ static inline void __bare_init setup_sdram(uint32_t base, uint32_t esdctl,
writel(esdctl, esdctlreg);
}
-void __bare_init __naked board_init_lowlevel(void)
+void __bare_init __naked reset(void)
{
uint32_t r;
#ifdef CONFIG_NAND_IMX_BOOT
unsigned int *trg, *src;
#endif
+ common_reset();
+
/* AIPS setup - Only setup MPROTx registers. The PACR default values are good.
* Set all MPROTx to be non-bufferable, trusted for R/W,
* not forced to user-mode.
diff --git a/arch/arm/boards/netx/platform.S b/arch/arm/boards/netx/platform.S
index 4961682..7d51b7b 100644
--- a/arch/arm/boards/netx/platform.S
+++ b/arch/arm/boards/netx/platform.S
@@ -21,6 +21,9 @@
* MA 02111-1307 USA
*/
-.globl board_init_lowlevel
-board_init_lowlevel:
- mov pc, lr
+#include <asm/barebox-arm-head.h>
+
+.globl reset
+reset:
+ common_reset r0
+ b board_init_lowlevel_return
diff --git a/arch/arm/boards/panda/lowlevel.c b/arch/arm/boards/panda/lowlevel.c
index 0b4b199..70a96d0 100644
--- a/arch/arm/boards/panda/lowlevel.c
+++ b/arch/arm/boards/panda/lowlevel.c
@@ -27,6 +27,7 @@
#include <mach/omap4-clock.h>
#include <mach/syslib.h>
#include <asm/barebox-arm.h>
+#include <asm/barebox-arm-head.h>
#define TPS62361_VSEL0_GPIO 7
@@ -77,15 +78,17 @@ static void noinline panda_init_lowlevel(void)
board_init_lowlevel_return();
}
-void board_init_lowlevel(void)
+void reset(void)
{
u32 r;
+ common_reset();
+
if (get_pc() > 0x80000000)
return;
r = 0x4030d000;
- __asm__ __volatile__("mov sp, %0" : : "r"(r));
+ __asm__ __volatile__("mov sp, %0" : : "r"(r));
panda_init_lowlevel();
}
diff --git a/arch/arm/boards/pcm027/lowlevel_init.S b/arch/arm/boards/pcm027/lowlevel_init.S
index a436a33..f69899e 100644
--- a/arch/arm/boards/pcm027/lowlevel_init.S
+++ b/arch/arm/boards/pcm027/lowlevel_init.S
@@ -31,6 +31,7 @@
#include <mach/pxa-regs.h>
#include <mach/regs-ost.h>
#include <mach/regs-intc.h>
+#include <asm/barebox-arm-head.h>
#define GPSR0 0x40E00018 /* GPIO Pin Output Set Register GPIO <31:00> */
#define GPSR1 0x40E0001C /* GPIO Pin Output Set Register GPIO <63:32> */
@@ -54,8 +55,10 @@
/*
* Memory setup
*/
-.globl board_init_lowlevel
-board_init_lowlevel:
+.globl reset
+reset:
+ common_reset r0
+
@ Preserve r8/r7 i.e. kernel entry values
@ Data cache might be active.
@@ -453,4 +456,5 @@ initclks:
/* -------------------------------------------------------------------- */
endlowlevel_init:
- mov pc, lr
+ b board_init_lowlevel_return
+
diff --git a/arch/arm/boards/pcm037/lowlevel_init.S b/arch/arm/boards/pcm037/lowlevel_init.S
index 1f8d38f..53b5811 100644
--- a/arch/arm/boards/pcm037/lowlevel_init.S
+++ b/arch/arm/boards/pcm037/lowlevel_init.S
@@ -23,6 +23,7 @@
#include <mach/imx-regs.h>
#include <mach/imx-pll.h>
+#include <asm/barebox-arm-head.h>
#define writel(val, reg) \
ldr r0, =reg; \
@@ -44,10 +45,11 @@
.section ".text_bare_init","ax"
-.globl board_init_lowlevel
-board_init_lowlevel:
+.globl reset
+reset:
+
+ common_reset r0
- mov r10, lr
writel(IPU_CONF_DI_EN, IPU_CONF)
writel(0x074B0BF5, IMX_CCM_BASE + CCM_CCMR)
@@ -91,7 +93,7 @@ clear_iomux:
cmp pc, #0x90000000
bhs 1f
- mov pc, r10
+ b board_init_lowlevel_return
1:
#if defined CONFIG_PCM037_SDRAM_BANK0_128MB
@@ -160,5 +162,5 @@ copy_loop:
ret:
#endif /* CONFIG_NAND_IMX_BOOT */
- mov pc, r10
+ b board_init_lowlevel_return
diff --git a/arch/arm/boards/pcm038/lowlevel.c b/arch/arm/boards/pcm038/lowlevel.c
index 3f29a83..d3ce528 100644
--- a/arch/arm/boards/pcm038/lowlevel.c
+++ b/arch/arm/boards/pcm038/lowlevel.c
@@ -31,6 +31,7 @@
#include <asm/system.h>
#include <asm-generic/memory_layout.h>
#include <asm-generic/sections.h>
+#include <asm/barebox-arm-head.h>
#include "pll.h"
@@ -53,13 +54,15 @@ static void __bare_init __naked insdram(void)
#define ESDCTL0_VAL (ESDCTL0_SDE | ESDCTL0_ROW13 | ESDCTL0_COL10)
-void __bare_init __naked board_init_lowlevel(void)
+void __bare_init __naked reset(void)
{
uint32_t r;
int i;
#ifdef CONFIG_NAND_IMX_BOOT
unsigned int *trg, *src;
#endif
+ common_reset();
+
/* ahb lite ip interface */
AIPI1_PSR0 = 0x20040304;
AIPI1_PSR1 = 0xDFFBFCFB;
diff --git a/arch/arm/boards/pcm043/lowlevel.c b/arch/arm/boards/pcm043/lowlevel.c
index fd6787f..dc51e05 100644
--- a/arch/arm/boards/pcm043/lowlevel.c
+++ b/arch/arm/boards/pcm043/lowlevel.c
@@ -29,6 +29,7 @@
#include <io.h>
#include <mach/imx-nand.h>
#include <asm/barebox-arm.h>
+#include <asm/barebox-arm-head.h>
#include <asm-generic/sections.h>
#include <asm-generic/memory_layout.h>
#include <asm/system.h>
@@ -64,7 +65,7 @@ static void __bare_init __naked insdram(void)
}
#endif
-void __bare_init __naked board_init_lowlevel(void)
+void __bare_init __naked reset(void)
{
uint32_t r, s;
unsigned long ccm_base = IMX_CCM_BASE;
@@ -73,6 +74,8 @@ void __bare_init __naked board_init_lowlevel(void)
unsigned int *trg, *src;
int i;
#endif
+ common_reset();
+
r = get_cr();
r |= CR_Z; /* Flow prediction (Z) */
r |= CR_U; /* unaligned accesses */
diff --git a/arch/arm/boards/pcm049/lowlevel.c b/arch/arm/boards/pcm049/lowlevel.c
index 65a29ec..0df8eb5 100644
--- a/arch/arm/boards/pcm049/lowlevel.c
+++ b/arch/arm/boards/pcm049/lowlevel.c
@@ -27,6 +27,7 @@
#include <mach/omap4-clock.h>
#include <mach/syslib.h>
#include <asm/barebox-arm.h>
+#include <asm/barebox-arm-head.h>
#define TPS62361_VSEL0_GPIO 182
@@ -87,10 +88,12 @@ static void noinline pcm049_init_lowlevel(void)
board_init_lowlevel_return();
}
-void board_init_lowlevel(void)
+void reset(void)
{
u32 r;
+ common_reset();
+
if (get_pc() > 0x80000000)
return;
diff --git a/arch/arm/boards/phycard-a-xl2/lowlevel.c b/arch/arm/boards/phycard-a-xl2/lowlevel.c
index 38f80c9..33277f3 100644
--- a/arch/arm/boards/phycard-a-xl2/lowlevel.c
+++ b/arch/arm/boards/phycard-a-xl2/lowlevel.c
@@ -27,6 +27,7 @@
#include <mach/omap4-clock.h>
#include <mach/syslib.h>
#include <asm/barebox-arm.h>
+#include <asm/barebox-arm-head.h>
#define TPS62361_VSEL0_GPIO 7
@@ -87,10 +88,12 @@ static noinline void pcaaxl2_init_lowlevel(void)
board_init_lowlevel_return();
}
-void board_init_lowlevel(void)
+void reset(void)
{
u32 r;
+ common_reset();
+
if (get_pc() > 0x80000000)
return;
diff --git a/arch/arm/boards/phycard-i.MX27/lowlevel_init.S b/arch/arm/boards/phycard-i.MX27/lowlevel_init.S
index c24edd4..b16afb5 100644
--- a/arch/arm/boards/phycard-i.MX27/lowlevel_init.S
+++ b/arch/arm/boards/phycard-i.MX27/lowlevel_init.S
@@ -7,6 +7,7 @@
#include <config.h>
#include <mach/imx-regs.h>
#include <mach/imx-pll.h>
+#include <asm/barebox-arm-head.h>
#define writel(val, reg) \
ldr r0, =reg; \
@@ -55,10 +56,9 @@
.section ".text_bare_init","ax"
-.globl board_init_lowlevel
-board_init_lowlevel:
-
- mov r10, lr
+.globl reset
+reset:
+ common_reset r0
/* ahb lite ip interface */
writel(0x20040304, AIPI1_PSR0)
@@ -72,7 +72,7 @@ board_init_lowlevel:
cmp pc, #0xc0000000
bhi 1f
- mov pc,r10
+ b board_init_lowlevel_return
1:
writel(IMX_PLL_PD(0) |
@@ -121,5 +121,5 @@ copy_loop:
#endif /* CONFIG_NAND_IMX_BOOT */
ret:
- mov pc,r10
+ b board_init_lowlevel_return
diff --git a/arch/arm/boards/scb9328/lowlevel_init.S b/arch/arm/boards/scb9328/lowlevel_init.S
index 5b02428..087e8e6 100644
--- a/arch/arm/boards/scb9328/lowlevel_init.S
+++ b/arch/arm/boards/scb9328/lowlevel_init.S
@@ -19,6 +19,7 @@
*/
#include <mach/imx-regs.h>
+#include <asm/barebox-arm-head.h>
#define CPU200
@@ -81,10 +82,10 @@
ldr r1, =val; \
str r1, [r0];
-.globl board_init_lowlevel
-board_init_lowlevel:
+.globl reset
+reset:
- mov r10, lr
+ common_reset r0
/* Change PERCLK1DIV to 14 ie 14+1 */
writel(CFG_PCDR_VAL, PCDR)
@@ -156,7 +157,7 @@ board_init_lowlevel:
cmp pc, #0x09000000
bhi 1f
- mov pc,r10
+ b board_init_lowlevel_return
1:
@@ -181,4 +182,4 @@ board_init_lowlevel:
writel(0x0, 0x08223000) /* CAS Latency 2, issue Mode Register Command, Burst Length = 8 */
writel(0x810a8200, SDCTL0) /* Set to Normal Mode CAS 2 */
- mov pc,r10
+ b board_init_lowlevel_return
diff --git a/arch/arm/cpu/Makefile b/arch/arm/cpu/Makefile
index 0ecc72e..f7ab276 100644
--- a/arch/arm/cpu/Makefile
+++ b/arch/arm/cpu/Makefile
@@ -1,7 +1,7 @@
obj-y += cpu.o
obj-$(CONFIG_ARM_EXCEPTIONS) += exceptions.o
obj-$(CONFIG_ARM_EXCEPTIONS) += interrupts.o
-obj-y += start.o start-reset.o
+obj-y += start.o
#
# Any variants can be called as start-armxyz.S
@@ -19,4 +19,4 @@ obj-$(CONFIG_CPU_32v7) += cache-armv7.o
pbl-$(CONFIG_CPU_32v7) += cache-armv7.o
obj-$(CONFIG_CACHE_L2X0) += cache-l2x0.o
-pbl-y += start-pbl.o start-reset.o
+pbl-y += start-pbl.o
diff --git a/arch/arm/cpu/start-pbl.c b/arch/arm/cpu/start-pbl.c
index 932a3da..823b9cc 100644
--- a/arch/arm/cpu/start-pbl.c
+++ b/arch/arm/cpu/start-pbl.c
@@ -41,6 +41,18 @@ void __naked __section(.text_head_entry) pbl_start(void)
barebox_arm_head();
}
+/*
+ * The actual reset vector. This code is position independent and usually
+ * does not run at the address it's linked at.
+ */
+#ifndef CONFIG_MACH_DO_LOWLEVEL_INIT
+void __naked __bare_init reset(void)
+{
+ common_reset();
+ board_init_lowlevel_return();
+}
+#endif
+
extern void *input_data;
extern void *input_data_end;
diff --git a/arch/arm/cpu/start-reset.c b/arch/arm/cpu/start-reset.c
deleted file mode 100644
index 46193ef..0000000
--- a/arch/arm/cpu/start-reset.c
+++ /dev/null
@@ -1,63 +0,0 @@
-/*
- * start-reset.c
- *
- * Copyright (c) 2010 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2
- * as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <init.h>
-#include <asm/system.h>
-#include <asm/barebox-arm.h>
-#include <asm/sections.h>
-
-/*
- * The actual reset vector. This code is position independent and usually
- * does not run at the address it's linked at.
- */
-void __naked __bare_init reset(void)
-{
- uint32_t r;
-
- /* set the cpu to SVC32 mode */
- __asm__ __volatile__("mrs %0, cpsr":"=r"(r));
- r &= ~0x1f;
- r |= 0xd3;
- __asm__ __volatile__("msr cpsr, %0" : : "r"(r));
-
- /* disable MMU stuff and caches */
- r = get_cr();
- r &= ~(CR_M | CR_C | CR_B | CR_S | CR_R | CR_V);
- r |= CR_I;
-
-#if __LINUX_ARM_ARCH__ >= 6
- r |= CR_U;
-#else
- r |= CR_A;
-#endif
-
-#ifdef __ARMEB__
- r |= CR_B;
-#endif
- set_cr(r);
-
-#ifdef CONFIG_MACH_DO_LOWLEVEL_INIT
- board_init_lowlevel();
-#endif
- board_init_lowlevel_return();
-}
diff --git a/arch/arm/cpu/start.c b/arch/arm/cpu/start.c
index 07e7dfe..e9a4620 100644
--- a/arch/arm/cpu/start.c
+++ b/arch/arm/cpu/start.c
@@ -53,6 +53,18 @@ void __naked __section(.text_entry) start(void)
}
/*
+ * The actual reset vector. This code is position independent and usually
+ * does not run at the address it's linked at.
+ */
+#ifndef CONFIG_MACH_DO_LOWLEVEL_INIT
+void __naked __bare_init reset(void)
+{
+ common_reset();
+ board_init_lowlevel_return();
+}
+#endif
+
+/*
* Board code can jump here by either returning from board_init_lowlevel
* or by calling this function directly.
*/
diff --git a/arch/arm/include/asm/barebox-arm-head.h b/arch/arm/include/asm/barebox-arm-head.h
index 0b1d786..eafad4e 100644
--- a/arch/arm/include/asm/barebox-arm-head.h
+++ b/arch/arm/include/asm/barebox-arm-head.h
@@ -1,6 +1,37 @@
#ifndef __ASM_ARM_HEAD_H
#define __ASM_ARM_HEAD_H
+#include <asm/system.h>
+
+#ifndef __ASSEMBLY__
+
+static inline void common_reset(void)
+{
+ uint32_t r;
+
+ /* set the cpu to SVC32 mode */
+ __asm__ __volatile__("mrs %0, cpsr":"=r"(r));
+ r &= ~0x1f;
+ r |= 0xd3;
+ __asm__ __volatile__("msr cpsr, %0" : : "r"(r));
+
+ /* disable MMU stuff and caches */
+ r = get_cr();
+ r &= ~(CR_M | CR_C | CR_B | CR_S | CR_R | CR_V);
+ r |= CR_I;
+
+#if __LINUX_ARM_ARCH__ >= 6
+ r |= CR_U;
+#else
+ r |= CR_A;
+#endif
+
+#ifdef __ARMEB__
+ r |= CR_B;
+#endif
+ set_cr(r);
+}
+
#ifdef CONFIG_HAVE_MACH_ARM_HEAD
#include <mach/barebox-arm-head.h>
#else
@@ -36,4 +67,41 @@ static inline void barebox_arm_head(void)
}
#endif
+#else
+
+.macro common_reset, scratch
+
+ /* set the cpu to SVC32 mode */
+ mrs \scratch, cpsr
+ bic \scratch, \scratch, #0x1f
+ orr \scratch, \scratch, #0xd3
+ msr cpsr, \scratch
+
+#if __LINUX_ARM_ARCH__ >= 7
+ isb
+#elif __LINUX_ARM_ARCH__ == 6
+ mcr p15, 0, \scratch, c7, c5, 4
+#endif
+
+ /* disable MMU stuff and caches */
+ mrc p15, 0, \scratch, c1, c0, 0
+ bic \scratch, \scratch , #(CR_M | CR_C | CR_B)
+ bic \scratch, \scratch, #(CR_S | CR_R | CR_V)
+ orr \scratch, \scratch, #CR_I
+
+#if __LINUX_ARM_ARCH__ >= 6
+ orr \scratch, \scratch, #CR_U
+#else
+ orr \scratch, \scratch, #CR_A
+#endif
+
+#ifdef __ARMEB__
+ orr \scratch, \scratch, #CR_B
+#endif
+
+ mcr p15, 0, \scratch, c1, c0, 0
+.endm
+
+#endif /* __ASSEMBLY__ */
+
#endif /* __ASM_ARM_HEAD_H */
diff --git a/arch/arm/include/asm/system.h b/arch/arm/include/asm/system.h
index 1d67492..26fb18c 100644
--- a/arch/arm/include/asm/system.h
+++ b/arch/arm/include/asm/system.h
@@ -56,6 +56,7 @@
#define CR_AFE (1 << 29) /* Access flag enable */
#define CR_TE (1 << 30) /* Thumb exception enable */
+#ifndef __ASSEMBLY__
static inline unsigned int get_cr(void)
{
unsigned int val;
@@ -69,4 +70,7 @@ static inline void set_cr(unsigned int val)
: : "r" (val) : "cc");
isb();
}
+
+#endif
+
#endif /* __ASM_ARM_SYSTEM_H */
diff --git a/arch/arm/mach-at91/at91rm9200_lowlevel_init.c b/arch/arm/mach-at91/at91rm9200_lowlevel_init.c
index 5340bba..3ce3e67 100644
--- a/arch/arm/mach-at91/at91rm9200_lowlevel_init.c
+++ b/arch/arm/mach-at91/at91rm9200_lowlevel_init.c
@@ -7,6 +7,7 @@
#include <common.h>
#include <asm/system.h>
#include <asm/barebox-arm.h>
+#include <asm/barebox-arm-head.h>
#include <mach/hardware.h>
#include <mach/at91rm9200.h>
#include <mach/at91rm9200_mc.h>
@@ -20,11 +21,13 @@ void static inline access_sdram(void)
writel(0x00000000, AT91_SDRAM_BASE);
}
-void __naked __bare_init board_init_lowlevel(void)
+void __naked __bare_init reset(void)
{
u32 r;
int i;
+ common_reset();
+
/*
* PMC Check if the PLL is already initialized
*/
diff --git a/arch/arm/mach-at91/at91sam926x_lowlevel_init.c b/arch/arm/mach-at91/at91sam926x_lowlevel_init.c
index 669f377..0ee0345 100644
--- a/arch/arm/mach-at91/at91sam926x_lowlevel_init.c
+++ b/arch/arm/mach-at91/at91sam926x_lowlevel_init.c
@@ -8,6 +8,7 @@
#include <common.h>
#include <asm/system.h>
#include <asm/barebox-arm.h>
+#include <asm/barebox-arm-head.h>
#include <mach/hardware.h>
#include <mach/at91_pmc.h>
#include <mach/at91_pio.h>
@@ -33,11 +34,13 @@ static void inline pmc_check_mckrdy(void)
} while (!(r & AT91_PMC_MCKRDY));
}
-void __naked __bare_init board_init_lowlevel(void)
+void __naked __bare_init reset(void)
{
u32 r;
int i;
+ common_reset();
+
at91_sys_write(AT91_WDT_MR, CONFIG_SYS_WDTC_WDMR_VAL);
/* configure PIOx as EBI0 D[16-31] */
diff --git a/arch/arm/mach-ep93xx/lowlevel_init.S b/arch/arm/mach-ep93xx/lowlevel_init.S
index 27c2c90..07da8ae 100644
--- a/arch/arm/mach-ep93xx/lowlevel_init.S
+++ b/arch/arm/mach-ep93xx/lowlevel_init.S
@@ -25,12 +25,11 @@
*/
#include <mach/ep93xx-regs.h>
+#include <asm/barebox-arm-head.h>
-.globl board_init_lowlevel
-board_init_lowlevel:
- /* backup return address */
- ldr r1, =SYSCON_SCRATCH0
- str lr, [r1]
+.globl reset
+reset:
+ common_reset r0
/* Turn on both LEDs */
bl red_LED_on
@@ -57,8 +56,4 @@ board_init_lowlevel:
orr r0, r0, #0xc0000000
mcr p15, 0, r0, c1, c0, 0
- /* restore return address */
- ldr r1, =SYSCON_SCRATCH0
- ldr lr, [r1]
-
- mov pc, lr
+ b board_init_lowlevel_return
diff --git a/arch/arm/mach-omap/Kconfig b/arch/arm/mach-omap/Kconfig
index 9c76a96..c610a1f 100644
--- a/arch/arm/mach-omap/Kconfig
+++ b/arch/arm/mach-omap/Kconfig
@@ -26,9 +26,6 @@ menu "OMAP Features"
config MACH_OMAP
bool
-config OMAP3_LOWLEVEL_INIT
- bool
-
choice
prompt "Select OMAP Variant"
@@ -36,7 +33,7 @@ config ARCH_OMAP3
bool "OMAP3"
select CPU_V7
select GENERIC_GPIO
- select OMAP3_LOWLEVEL_INIT
+ select MACH_HAS_LOWLEVEL_INIT
select OMAP_CLOCK_SOURCE_S32K
help
Say Y here if you are using Texas Instrument's OMAP343x based platform
diff --git a/arch/arm/mach-omap/omap3_core.S b/arch/arm/mach-omap/omap3_core.S
index d1be6e5..7c31e1e 100644
--- a/arch/arm/mach-omap/omap3_core.S
+++ b/arch/arm/mach-omap/omap3_core.S
@@ -40,8 +40,10 @@
#include <mach/silicon.h>
#include <mach/wdt.h>
#include <mach/clocks.h>
+#include <asm/barebox-arm-head.h>
-ENTRY(board_init_lowlevel)
+#ifdef CONFIG_MACH_DO_LOWLEVEL_INIT
+ENTRY(reset)
/* Invalidate all Dcaches */
#ifndef CONFIG_CPU_V7_DCACHE_SKIP
/* If Arch specific ROM code SMI handling does not exist */
@@ -90,5 +92,6 @@ finished_inval:
isb
#endif /* CONFIG_CPU_V7_DCACHE_SKIP */
/* back to arch calling code */
- mov pc, lr
-ENDPROC(board_init_lowlevel)
+ b board_init_lowlevel_return
+ENDPROC(reset)
+#endif
--
1.7.10.4
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH 4/4] ARM: give boards control of the reset entry point
2012-09-24 8:18 ` [PATCH 4/4] ARM: give boards control of the reset entry point Jan Luebbe
@ 2012-09-25 11:28 ` Sascha Hauer
0 siblings, 0 replies; 5+ messages in thread
From: Sascha Hauer @ 2012-09-25 11:28 UTC (permalink / raw)
To: Jan Luebbe; +Cc: barebox
Hi Jan,
Could you redo this based on the next-stable tag I created? There are
two additional boards to handle now.
Sascha
On Mon, Sep 24, 2012 at 10:18:34AM +0200, Jan Luebbe wrote:
> On some SoCs (for example AM35xx), the ROM bootloader passes useful
> information in r0 when jumping to barebox.
>
> To avoid overwriting this in the generic reset code, we introduce
> common_reset as a C function and as an assembler macro. This is then
> called form the reset entry point (either in common or in board code).
>
> This patch is based on code by Sascha Hauer <s.hauer@pengutronix.de>.
>
> Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
> ---
> arch/arm/boards/a9m2410/lowlevel_init.S | 17 +++--
> arch/arm/boards/a9m2440/lowlevel_init.S | 15 ++---
> arch/arm/boards/at91sam9260ek/lowlevel_init.S | 9 ++-
> arch/arm/boards/eukrea_cpuimx25/lowlevel.c | 5 +-
> arch/arm/boards/eukrea_cpuimx27/lowlevel_init.S | 11 ++--
> arch/arm/boards/eukrea_cpuimx35/lowlevel.c | 5 +-
> .../boards/freescale-mx25-3-stack/lowlevel_init.S | 11 ++--
> .../boards/freescale-mx35-3-stack/lowlevel_init.S | 12 ++--
> .../boards/friendlyarm-mini2440/lowlevel_init.S | 18 +++---
> arch/arm/boards/friendlyarm-tiny210/lowlevel.c | 5 +-
> arch/arm/boards/guf-cupid/lowlevel.c | 7 +-
> arch/arm/boards/guf-neso/lowlevel.c | 6 +-
> arch/arm/boards/imx21ads/lowlevel_init.S | 12 ++--
> arch/arm/boards/imx27ads/lowlevel_init.S | 11 ++--
> arch/arm/boards/karo-tx25/lowlevel.c | 5 +-
> arch/arm/boards/netx/platform.S | 9 ++-
> arch/arm/boards/panda/lowlevel.c | 7 +-
> arch/arm/boards/pcm027/lowlevel_init.S | 10 ++-
> arch/arm/boards/pcm037/lowlevel_init.S | 12 ++--
> arch/arm/boards/pcm038/lowlevel.c | 5 +-
> arch/arm/boards/pcm043/lowlevel.c | 5 +-
> arch/arm/boards/pcm049/lowlevel.c | 5 +-
> arch/arm/boards/phycard-a-xl2/lowlevel.c | 5 +-
> arch/arm/boards/phycard-i.MX27/lowlevel_init.S | 12 ++--
> arch/arm/boards/scb9328/lowlevel_init.S | 11 ++--
> arch/arm/cpu/Makefile | 4 +-
> arch/arm/cpu/start-pbl.c | 12 ++++
> arch/arm/cpu/start-reset.c | 63 ------------------
> arch/arm/cpu/start.c | 12 ++++
> arch/arm/include/asm/barebox-arm-head.h | 68 ++++++++++++++++++++
> arch/arm/include/asm/system.h | 4 ++
> arch/arm/mach-at91/at91rm9200_lowlevel_init.c | 5 +-
> arch/arm/mach-at91/at91sam926x_lowlevel_init.c | 5 +-
> arch/arm/mach-ep93xx/lowlevel_init.S | 15 ++---
> arch/arm/mach-omap/Kconfig | 5 +-
> arch/arm/mach-omap/omap3_core.S | 9 ++-
> 36 files changed, 257 insertions(+), 175 deletions(-)
> delete mode 100644 arch/arm/cpu/start-reset.c
>
> diff --git a/arch/arm/boards/a9m2410/lowlevel_init.S b/arch/arm/boards/a9m2410/lowlevel_init.S
> index 0463b26..502ecdd 100644
> --- a/arch/arm/boards/a9m2410/lowlevel_init.S
> +++ b/arch/arm/boards/a9m2410/lowlevel_init.S
> @@ -4,13 +4,14 @@
>
> #include <config.h>
> #include <mach/s3c-iomap.h>
> +#include <asm/barebox-arm-head.h>
>
> - .section ".text_bare_init.board_init_lowlevel","ax"
> + .section ".text_bare_init.reset","ax"
>
> -.globl board_init_lowlevel
> -board_init_lowlevel:
> +.globl reset
> +reset:
>
> - mov r10, lr /* save the link register */
> + common_reset r0
>
> bl s3c24x0_disable_wd
>
> @@ -20,7 +21,7 @@ board_init_lowlevel:
> cmp pc, #S3C_SDRAM_END
> bhs 1f
>
> - mov pc, r10
> + b board_init_lowlevel_return
>
> /* we are running from NOR or NAND/SRAM memory. Do further initialisation */
> 1:
> @@ -29,9 +30,7 @@ board_init_lowlevel:
> bl s3c24x0_sdram_init
>
> #ifdef CONFIG_S3C_NAND_BOOT
> - mov lr, r10 /* restore the link register */
> /* up to here we are running from the internal SRAM area */
> - b s3c24x0_nand_boot /* does return directly to our caller into SDRAM */
> -#else
> - mov pc, r10
> + bl s3c24x0_nand_boot
> #endif
> + b board_init_lowlevel_return
> diff --git a/arch/arm/boards/a9m2440/lowlevel_init.S b/arch/arm/boards/a9m2440/lowlevel_init.S
> index 305014c..da29efd 100644
> --- a/arch/arm/boards/a9m2440/lowlevel_init.S
> +++ b/arch/arm/boards/a9m2440/lowlevel_init.S
> @@ -5,8 +5,9 @@
> #include <config.h>
> #include <mach/s3c-iomap.h>
> #include <mach/s3c24xx-gpio.h>
> +#include <asm/barebox-arm-head.h>
>
> - .section ".text_bare_init.board_init_lowlevel","ax"
> + .section ".text_bare_init.reset","ax"
>
> /*
> * To be able to setup the SDRAM interface correctly, we need some
> @@ -211,10 +212,10 @@ SDRAMDATA:
>
> /* ------------------------------------------------------------------------ */
>
> -.globl board_init_lowlevel
> -board_init_lowlevel:
> +.globl reset
> +reset:
>
> - mov r10, lr /* save the link register */
> + common_reset r0
>
> bl s3c24x0_disable_wd
>
> @@ -233,9 +234,7 @@ board_init_lowlevel:
> bl sdram_init
>
> #ifdef CONFIG_S3C_NAND_BOOT
> - mov lr, r10 /* restore the link register */
> /* up to here we are running from the internal SRAM area */
> - b s3c24x0_nand_boot /* does return directly to our caller into SDRAM */
> -#else
> - mov pc, r10
> + bl s3c24x0_nand_boot
> #endif
> + b board_init_lowlevel_return
> diff --git a/arch/arm/boards/at91sam9260ek/lowlevel_init.S b/arch/arm/boards/at91sam9260ek/lowlevel_init.S
> index 4961682..7d51b7b 100644
> --- a/arch/arm/boards/at91sam9260ek/lowlevel_init.S
> +++ b/arch/arm/boards/at91sam9260ek/lowlevel_init.S
> @@ -21,6 +21,9 @@
> * MA 02111-1307 USA
> */
>
> -.globl board_init_lowlevel
> -board_init_lowlevel:
> - mov pc, lr
> +#include <asm/barebox-arm-head.h>
> +
> +.globl reset
> +reset:
> + common_reset r0
> + b board_init_lowlevel_return
> diff --git a/arch/arm/boards/eukrea_cpuimx25/lowlevel.c b/arch/arm/boards/eukrea_cpuimx25/lowlevel.c
> index 89066e9..ca94ac5 100644
> --- a/arch/arm/boards/eukrea_cpuimx25/lowlevel.c
> +++ b/arch/arm/boards/eukrea_cpuimx25/lowlevel.c
> @@ -29,6 +29,7 @@
> #include <io.h>
> #include <mach/imx-nand.h>
> #include <asm/barebox-arm.h>
> +#include <asm/barebox-arm-head.h>
> #include <asm-generic/sections.h>
> #include <asm-generic/memory_layout.h>
> #include <asm/system.h>
> @@ -48,7 +49,7 @@ static void __bare_init __naked insdram(void)
> }
> #endif
>
> -void __bare_init __naked board_init_lowlevel(void)
> +void __bare_init __naked reset(void)
> {
> uint32_t r;
> #ifdef CONFIG_NAND_IMX_BOOT
> @@ -57,6 +58,8 @@ void __bare_init __naked board_init_lowlevel(void)
> #endif
> register uint32_t loops = 0x20000;
>
> + common_reset();
> +
> /* restart the MPLL and wait until it's stable */
> writel(readl(IMX_CCM_BASE + CCM_CCTL) | (1 << 27),
> IMX_CCM_BASE + CCM_CCTL);
> diff --git a/arch/arm/boards/eukrea_cpuimx27/lowlevel_init.S b/arch/arm/boards/eukrea_cpuimx27/lowlevel_init.S
> index 0dae3ec..af4deeb 100644
> --- a/arch/arm/boards/eukrea_cpuimx27/lowlevel_init.S
> +++ b/arch/arm/boards/eukrea_cpuimx27/lowlevel_init.S
> @@ -1,6 +1,7 @@
> #include <config.h>
> #include <asm-generic/memory_layout.h>
> #include <mach/imx-regs.h>
> +#include <asm/barebox-arm-head.h>
>
> #define writel(val, reg) \
> ldr r0, =reg; \
> @@ -60,10 +61,10 @@
>
> .section ".text_bare_init","ax"
>
> -.globl board_init_lowlevel
> -board_init_lowlevel:
> +.globl reset
> +reset:
>
> - mov r10, lr
> + common_reset r0
>
> /* ahb lite ip interface */
> writel(0x20040304, AIPI1_PSR0)
> @@ -103,7 +104,7 @@ board_init_lowlevel:
> cmp pc, #0xc0000000
> bhi 1f
>
> - mov pc,r10
> + b board_init_lowlevel_return
> 1:
> sdram_init
>
> @@ -135,4 +136,4 @@ copy_loop:
> #endif /* CONFIG_NAND_IMX_BOOT */
>
> ret:
> - mov pc,r10
> + b board_init_lowlevel_return
> diff --git a/arch/arm/boards/eukrea_cpuimx35/lowlevel.c b/arch/arm/boards/eukrea_cpuimx35/lowlevel.c
> index 57867dc..b8dec71 100644
> --- a/arch/arm/boards/eukrea_cpuimx35/lowlevel.c
> +++ b/arch/arm/boards/eukrea_cpuimx35/lowlevel.c
> @@ -29,6 +29,7 @@
> #include <io.h>
> #include <mach/imx-nand.h>
> #include <asm/barebox-arm.h>
> +#include <asm/barebox-arm-head.h>
> #include <asm-generic/sections.h>
> #include <asm-generic/memory_layout.h>
> #include <asm/system.h>
> @@ -59,7 +60,7 @@ static void __bare_init __naked insdram(void)
> }
> #endif
>
> -void __bare_init __naked board_init_lowlevel(void)
> +void __bare_init __naked reset(void)
> {
> uint32_t r, s;
> unsigned long ccm_base = IMX_CCM_BASE;
> @@ -69,6 +70,8 @@ void __bare_init __naked board_init_lowlevel(void)
> #endif
> register uint32_t loops = 0x20000;
>
> + common_reset();
> +
> r = get_cr();
> r |= CR_Z; /* Flow prediction (Z) */
> r |= CR_U; /* unaligned accesses */
> diff --git a/arch/arm/boards/freescale-mx25-3-stack/lowlevel_init.S b/arch/arm/boards/freescale-mx25-3-stack/lowlevel_init.S
> index fa0f957..6157949 100644
> --- a/arch/arm/boards/freescale-mx25-3-stack/lowlevel_init.S
> +++ b/arch/arm/boards/freescale-mx25-3-stack/lowlevel_init.S
> @@ -25,6 +25,7 @@
> #include <mach/imx-regs.h>
> #include <mach/imx-pll.h>
> #include <mach/esdctl.h>
> +#include <asm/barebox-arm-head.h>
>
> #define writel(val, reg) \
> ldr r0, =reg; \
> @@ -52,9 +53,9 @@ MPCTL_PARAM_532_W: .word MPCTL_PARAM_532
> PPCTL_PARAM_W: .word PPCTL_PARAM_300
> CCM_BASE_ADDR_W: .word IMX_CCM_BASE
>
> -.globl board_init_lowlevel
> -board_init_lowlevel:
> - mov r10, lr
> +.globl reset
> +reset:
> + common_reset r0
>
> #define MX25_CCM_MCR 0x64
>
> @@ -80,7 +81,7 @@ board_init_lowlevel:
> cmp pc, #0x90000000
> bhi 1f
>
> - mov pc, lr
> + b board_init_lowlevel_return
>
> 1:
> ldr r0, ESDCTL_BASE_W
> @@ -128,7 +129,7 @@ copy_loop:
> #endif /* CONFIG_NAND_IMX_BOOT */
>
> ret:
> - mov pc, r10
> + b board_init_lowlevel_return
>
> /*
> * r0: control base, r1: ram bank base
> diff --git a/arch/arm/boards/freescale-mx35-3-stack/lowlevel_init.S b/arch/arm/boards/freescale-mx35-3-stack/lowlevel_init.S
> index 837d2ff..a5e8c19 100644
> --- a/arch/arm/boards/freescale-mx35-3-stack/lowlevel_init.S
> +++ b/arch/arm/boards/freescale-mx35-3-stack/lowlevel_init.S
> @@ -26,6 +26,8 @@
> #include <mach/esdctl.h>
> #include <asm/cache-l2x0.h>
> #include <asm-generic/memory_layout.h>
> +#include <asm/barebox-arm-head.h>
> +
> #include "board-mx35_3stack.h"
>
> #define CSD0_BASE_ADDR 0x80000000
> @@ -58,9 +60,9 @@ MPCTL_PARAM_532_W: .word MPCTL_PARAM_532
> PPCTL_PARAM_W: .word PPCTL_PARAM_300
> CCM_BASE_ADDR_W: .word IMX_CCM_BASE
>
> -.globl board_init_lowlevel
> -board_init_lowlevel:
> - mov r10, lr
> +.globl reset
> +reset:
> + common_reset r0
>
> mrc 15, 0, r1, c1, c0, 0
>
> @@ -128,7 +130,7 @@ board_init_lowlevel:
> cmp pc, #CSD1_BASE_ADDR
> bhi 1f
>
> - mov pc, r10
> + b board_init_lowlevel_return
>
> 1:
> ldr r0, =ESDCTL_BASE_ADDR
> @@ -183,7 +185,7 @@ copy_loop:
> ret:
> #endif /* CONFIG_NAND_IMX_BOOT */
>
> - mov pc, r10
> + b board_init_lowlevel_return
>
> /*
> * r0: ESDCTL control base, r1: sdram slot base
> diff --git a/arch/arm/boards/friendlyarm-mini2440/lowlevel_init.S b/arch/arm/boards/friendlyarm-mini2440/lowlevel_init.S
> index 827cf00..5c06b1c 100644
> --- a/arch/arm/boards/friendlyarm-mini2440/lowlevel_init.S
> +++ b/arch/arm/boards/friendlyarm-mini2440/lowlevel_init.S
> @@ -4,15 +4,15 @@
>
> #include <config.h>
> #include <mach/s3c-iomap.h>
> +#include <asm/barebox-arm-head.h>
>
> - .section ".text_bare_init.board_init_lowlevel","ax"
> + .section ".text_bare_init.reset","ax"
>
> /* ------------------------------------------------------------------------ */
>
> -.globl board_init_lowlevel
> -board_init_lowlevel:
> -
> - mov r10, lr /* save the link register */
> +.globl reset
> +reset:
> + common_reset r0
>
> bl s3c24x0_disable_wd
>
> @@ -22,7 +22,7 @@ board_init_lowlevel:
> cmp pc, #S3C_SDRAM_END
> bhs 1f
>
> - mov pc, r10
> + b board_init_lowlevel_return
>
> /* we are running from NOR or NAND/SRAM memory. Do further initialisation */
> 1:
> @@ -31,9 +31,7 @@ board_init_lowlevel:
> bl s3c24x0_sdram_init
>
> #ifdef CONFIG_S3C_NAND_BOOT
> - mov lr, r10 /* restore the link register */
> /* up to here we are running from the internal SRAM area */
> - b s3c24x0_nand_boot /* does return directly to our caller into SDRAM */
> -#else
> - mov pc, r10
> + bl s3c24x0_nand_boot
> #endif
> + b board_init_lowlevel_return
> diff --git a/arch/arm/boards/friendlyarm-tiny210/lowlevel.c b/arch/arm/boards/friendlyarm-tiny210/lowlevel.c
> index 19739d8..791918a 100644
> --- a/arch/arm/boards/friendlyarm-tiny210/lowlevel.c
> +++ b/arch/arm/boards/friendlyarm-tiny210/lowlevel.c
> @@ -24,6 +24,7 @@
> #include <init.h>
> #include <io.h>
> #include <asm/barebox-arm.h>
> +#include <asm/barebox-arm-head.h>
> #include <asm/sections.h>
> #include <mach/s3c-iomap.h>
> #include <mach/s3c-clocks.h>
> @@ -49,10 +50,12 @@ int __bare_init s5p_irom_load_mmc(void *dest, uint32_t start_block, uint16_t blo
> }
>
>
> -void __bare_init board_init_lowlevel(void)
> +void __bare_init reset(void)
> {
> uint32_t r;
>
> + common_reset();
> +
> #ifdef CONFIG_S3C_PLL_INIT
> s5p_init_pll();
> #endif
> diff --git a/arch/arm/boards/guf-cupid/lowlevel.c b/arch/arm/boards/guf-cupid/lowlevel.c
> index 8fa9152..d50090b 100644
> --- a/arch/arm/boards/guf-cupid/lowlevel.c
> +++ b/arch/arm/boards/guf-cupid/lowlevel.c
> @@ -29,6 +29,7 @@
> #include <io.h>
> #include <mach/imx-nand.h>
> #include <asm/barebox-arm.h>
> +#include <asm/barebox-arm-head.h>
> #include <asm-generic/sections.h>
> #include <asm-generic/memory_layout.h>
> #include <asm/system.h>
> @@ -182,7 +183,7 @@ static void __bare_init noinline setup_sdram(u32 memsize, u32 mode, u32 sdram_ad
> #define UNALIGNED_ACCESS_ENABLE
> #define LOW_INT_LATENCY_ENABLE
>
> -void __bare_init __naked board_init_lowlevel(void)
> +void __bare_init __naked reset(void)
> {
> u32 r0, r1;
> void *iomuxc_base = (void *)IMX_IOMUXC_BASE;
> @@ -191,8 +192,10 @@ void __bare_init __naked board_init_lowlevel(void)
> unsigned int *trg, *src;
> #endif
>
> + common_reset();
> +
> r0 = 0x10000000 + 128 * 1024 - 16;
> - __asm__ __volatile__("mov sp, %0" : : "r"(r0));
> + __asm__ __volatile__("mov sp, %0" : : "r"(r0));
>
> /*
> * ARM1136 init
> diff --git a/arch/arm/boards/guf-neso/lowlevel.c b/arch/arm/boards/guf-neso/lowlevel.c
> index 9b206be..5bb2d21 100644
> --- a/arch/arm/boards/guf-neso/lowlevel.c
> +++ b/arch/arm/boards/guf-neso/lowlevel.c
> @@ -29,6 +29,7 @@
> #include <io.h>
> #include <mach/imx-nand.h>
> #include <asm/barebox-arm.h>
> +#include <asm/barebox-arm-head.h>
> #include <asm/system.h>
> #include <asm-generic/sections.h>
> #include <asm-generic/memory_layout.h>
> @@ -52,13 +53,16 @@ static void __bare_init __naked insdram(void)
>
> #define ESDCTL0_VAL (ESDCTL0_SDE | ESDCTL0_ROW13 | ESDCTL0_COL10)
>
> -void __bare_init __naked board_init_lowlevel(void)
> +void __bare_init __naked reset(void)
> {
> uint32_t r;
> int i;
> #ifdef CONFIG_NAND_IMX_BOOT
> unsigned int *trg, *src;
> #endif
> +
> + common_reset();
> +
> /* ahb lite ip interface */
> AIPI1_PSR0 = 0x20040304;
> AIPI1_PSR1 = 0xDFFBFCFB;
> diff --git a/arch/arm/boards/imx21ads/lowlevel_init.S b/arch/arm/boards/imx21ads/lowlevel_init.S
> index 1aeea57..1568f3c 100644
> --- a/arch/arm/boards/imx21ads/lowlevel_init.S
> +++ b/arch/arm/boards/imx21ads/lowlevel_init.S
> @@ -20,14 +20,14 @@
> #include <config.h>
> #include <asm-generic/memory_layout.h>
> #include <mach/imx-regs.h>
> +#include <asm/barebox-arm-head.h>
>
> .section ".text_bare_init","ax"
>
> -.globl board_init_lowlevel
> -board_init_lowlevel:
> +.globl reset
> +reset:
>
> -/* Save lr, because it is overwritten by the calls to mem_delay. */
> - mov r10, lr
> + common_reset r0
>
> /*
> * Initialize the AHB-Lite IP Interface (AIPI) module (to enable access to
> @@ -79,7 +79,7 @@ board_init_lowlevel:
> cmp pc, #0xc8000000
> bhi 1f
>
> - mov pc, r10
> + b board_init_lowlevel_return
> 1:
>
> /* Precharge */
> @@ -149,7 +149,7 @@ copy_loop:
> #endif /* CONFIG_NAND_IMX_BOOT */
>
> ret:
> - mov pc, r10
> + b board_init_lowlevel_return
>
> /*
> * spin for a while. we need to wait at least 200 usecs.
> diff --git a/arch/arm/boards/imx27ads/lowlevel_init.S b/arch/arm/boards/imx27ads/lowlevel_init.S
> index df12aea..1bebb1d 100644
> --- a/arch/arm/boards/imx27ads/lowlevel_init.S
> +++ b/arch/arm/boards/imx27ads/lowlevel_init.S
> @@ -6,6 +6,7 @@
>
> #include <config.h>
> #include <mach/imx-regs.h>
> +#include <asm/barebox-arm-head.h>
>
> #define writel(val, reg) \
> ldr r0, =reg; \
> @@ -111,10 +112,10 @@ NORMAL_MODE .long 0x00000000 // system/external device dependent data (SMODE=00
> writel(0x0000000c, 0xD8001010)
> .endm
>
> -.globl board_init_lowlevel
> -board_init_lowlevel:
> +.globl reset
> +reset:
>
> - mov r10, lr
> + common_reset r0
>
> /* ahb lite ip interface */
> writel(0x20040304, AIPI1_PSR0)
> @@ -164,9 +165,9 @@ board_init_lowlevel:
> cmp pc, #0xc0000000
> bhi 1f
>
> - mov pc,r10
> + b board_init_lowlevel_return
> 1:
> sdram_init_sha
>
> - mov pc,r10
> + b board_init_lowlevel_return
>
> diff --git a/arch/arm/boards/karo-tx25/lowlevel.c b/arch/arm/boards/karo-tx25/lowlevel.c
> index 9f1c5d6..f06cc7c 100644
> --- a/arch/arm/boards/karo-tx25/lowlevel.c
> +++ b/arch/arm/boards/karo-tx25/lowlevel.c
> @@ -27,6 +27,7 @@
> #include <io.h>
> #include <mach/imx-nand.h>
> #include <asm/barebox-arm.h>
> +#include <asm/barebox-arm-head.h>
> #include <asm/system.h>
> #include <asm-generic/sections.h>
> #include <asm-generic/memory_layout.h>
> @@ -70,13 +71,15 @@ static inline void __bare_init setup_sdram(uint32_t base, uint32_t esdctl,
> writel(esdctl, esdctlreg);
> }
>
> -void __bare_init __naked board_init_lowlevel(void)
> +void __bare_init __naked reset(void)
> {
> uint32_t r;
> #ifdef CONFIG_NAND_IMX_BOOT
> unsigned int *trg, *src;
> #endif
>
> + common_reset();
> +
> /* AIPS setup - Only setup MPROTx registers. The PACR default values are good.
> * Set all MPROTx to be non-bufferable, trusted for R/W,
> * not forced to user-mode.
> diff --git a/arch/arm/boards/netx/platform.S b/arch/arm/boards/netx/platform.S
> index 4961682..7d51b7b 100644
> --- a/arch/arm/boards/netx/platform.S
> +++ b/arch/arm/boards/netx/platform.S
> @@ -21,6 +21,9 @@
> * MA 02111-1307 USA
> */
>
> -.globl board_init_lowlevel
> -board_init_lowlevel:
> - mov pc, lr
> +#include <asm/barebox-arm-head.h>
> +
> +.globl reset
> +reset:
> + common_reset r0
> + b board_init_lowlevel_return
> diff --git a/arch/arm/boards/panda/lowlevel.c b/arch/arm/boards/panda/lowlevel.c
> index 0b4b199..70a96d0 100644
> --- a/arch/arm/boards/panda/lowlevel.c
> +++ b/arch/arm/boards/panda/lowlevel.c
> @@ -27,6 +27,7 @@
> #include <mach/omap4-clock.h>
> #include <mach/syslib.h>
> #include <asm/barebox-arm.h>
> +#include <asm/barebox-arm-head.h>
>
> #define TPS62361_VSEL0_GPIO 7
>
> @@ -77,15 +78,17 @@ static void noinline panda_init_lowlevel(void)
> board_init_lowlevel_return();
> }
>
> -void board_init_lowlevel(void)
> +void reset(void)
> {
> u32 r;
>
> + common_reset();
> +
> if (get_pc() > 0x80000000)
> return;
>
> r = 0x4030d000;
> - __asm__ __volatile__("mov sp, %0" : : "r"(r));
> + __asm__ __volatile__("mov sp, %0" : : "r"(r));
>
> panda_init_lowlevel();
> }
> diff --git a/arch/arm/boards/pcm027/lowlevel_init.S b/arch/arm/boards/pcm027/lowlevel_init.S
> index a436a33..f69899e 100644
> --- a/arch/arm/boards/pcm027/lowlevel_init.S
> +++ b/arch/arm/boards/pcm027/lowlevel_init.S
> @@ -31,6 +31,7 @@
> #include <mach/pxa-regs.h>
> #include <mach/regs-ost.h>
> #include <mach/regs-intc.h>
> +#include <asm/barebox-arm-head.h>
>
> #define GPSR0 0x40E00018 /* GPIO Pin Output Set Register GPIO <31:00> */
> #define GPSR1 0x40E0001C /* GPIO Pin Output Set Register GPIO <63:32> */
> @@ -54,8 +55,10 @@
> /*
> * Memory setup
> */
> -.globl board_init_lowlevel
> -board_init_lowlevel:
> +.globl reset
> +reset:
> + common_reset r0
> +
> @ Preserve r8/r7 i.e. kernel entry values
>
> @ Data cache might be active.
> @@ -453,4 +456,5 @@ initclks:
> /* -------------------------------------------------------------------- */
>
> endlowlevel_init:
> - mov pc, lr
> + b board_init_lowlevel_return
> +
> diff --git a/arch/arm/boards/pcm037/lowlevel_init.S b/arch/arm/boards/pcm037/lowlevel_init.S
> index 1f8d38f..53b5811 100644
> --- a/arch/arm/boards/pcm037/lowlevel_init.S
> +++ b/arch/arm/boards/pcm037/lowlevel_init.S
> @@ -23,6 +23,7 @@
>
> #include <mach/imx-regs.h>
> #include <mach/imx-pll.h>
> +#include <asm/barebox-arm-head.h>
>
> #define writel(val, reg) \
> ldr r0, =reg; \
> @@ -44,10 +45,11 @@
>
> .section ".text_bare_init","ax"
>
> -.globl board_init_lowlevel
> -board_init_lowlevel:
> +.globl reset
> +reset:
> +
> + common_reset r0
>
> - mov r10, lr
> writel(IPU_CONF_DI_EN, IPU_CONF)
> writel(0x074B0BF5, IMX_CCM_BASE + CCM_CCMR)
>
> @@ -91,7 +93,7 @@ clear_iomux:
> cmp pc, #0x90000000
> bhs 1f
>
> - mov pc, r10
> + b board_init_lowlevel_return
> 1:
>
> #if defined CONFIG_PCM037_SDRAM_BANK0_128MB
> @@ -160,5 +162,5 @@ copy_loop:
> ret:
> #endif /* CONFIG_NAND_IMX_BOOT */
>
> - mov pc, r10
> + b board_init_lowlevel_return
>
> diff --git a/arch/arm/boards/pcm038/lowlevel.c b/arch/arm/boards/pcm038/lowlevel.c
> index 3f29a83..d3ce528 100644
> --- a/arch/arm/boards/pcm038/lowlevel.c
> +++ b/arch/arm/boards/pcm038/lowlevel.c
> @@ -31,6 +31,7 @@
> #include <asm/system.h>
> #include <asm-generic/memory_layout.h>
> #include <asm-generic/sections.h>
> +#include <asm/barebox-arm-head.h>
>
> #include "pll.h"
>
> @@ -53,13 +54,15 @@ static void __bare_init __naked insdram(void)
>
> #define ESDCTL0_VAL (ESDCTL0_SDE | ESDCTL0_ROW13 | ESDCTL0_COL10)
>
> -void __bare_init __naked board_init_lowlevel(void)
> +void __bare_init __naked reset(void)
> {
> uint32_t r;
> int i;
> #ifdef CONFIG_NAND_IMX_BOOT
> unsigned int *trg, *src;
> #endif
> + common_reset();
> +
> /* ahb lite ip interface */
> AIPI1_PSR0 = 0x20040304;
> AIPI1_PSR1 = 0xDFFBFCFB;
> diff --git a/arch/arm/boards/pcm043/lowlevel.c b/arch/arm/boards/pcm043/lowlevel.c
> index fd6787f..dc51e05 100644
> --- a/arch/arm/boards/pcm043/lowlevel.c
> +++ b/arch/arm/boards/pcm043/lowlevel.c
> @@ -29,6 +29,7 @@
> #include <io.h>
> #include <mach/imx-nand.h>
> #include <asm/barebox-arm.h>
> +#include <asm/barebox-arm-head.h>
> #include <asm-generic/sections.h>
> #include <asm-generic/memory_layout.h>
> #include <asm/system.h>
> @@ -64,7 +65,7 @@ static void __bare_init __naked insdram(void)
> }
> #endif
>
> -void __bare_init __naked board_init_lowlevel(void)
> +void __bare_init __naked reset(void)
> {
> uint32_t r, s;
> unsigned long ccm_base = IMX_CCM_BASE;
> @@ -73,6 +74,8 @@ void __bare_init __naked board_init_lowlevel(void)
> unsigned int *trg, *src;
> int i;
> #endif
> + common_reset();
> +
> r = get_cr();
> r |= CR_Z; /* Flow prediction (Z) */
> r |= CR_U; /* unaligned accesses */
> diff --git a/arch/arm/boards/pcm049/lowlevel.c b/arch/arm/boards/pcm049/lowlevel.c
> index 65a29ec..0df8eb5 100644
> --- a/arch/arm/boards/pcm049/lowlevel.c
> +++ b/arch/arm/boards/pcm049/lowlevel.c
> @@ -27,6 +27,7 @@
> #include <mach/omap4-clock.h>
> #include <mach/syslib.h>
> #include <asm/barebox-arm.h>
> +#include <asm/barebox-arm-head.h>
>
> #define TPS62361_VSEL0_GPIO 182
>
> @@ -87,10 +88,12 @@ static void noinline pcm049_init_lowlevel(void)
> board_init_lowlevel_return();
> }
>
> -void board_init_lowlevel(void)
> +void reset(void)
> {
> u32 r;
>
> + common_reset();
> +
> if (get_pc() > 0x80000000)
> return;
>
> diff --git a/arch/arm/boards/phycard-a-xl2/lowlevel.c b/arch/arm/boards/phycard-a-xl2/lowlevel.c
> index 38f80c9..33277f3 100644
> --- a/arch/arm/boards/phycard-a-xl2/lowlevel.c
> +++ b/arch/arm/boards/phycard-a-xl2/lowlevel.c
> @@ -27,6 +27,7 @@
> #include <mach/omap4-clock.h>
> #include <mach/syslib.h>
> #include <asm/barebox-arm.h>
> +#include <asm/barebox-arm-head.h>
>
> #define TPS62361_VSEL0_GPIO 7
>
> @@ -87,10 +88,12 @@ static noinline void pcaaxl2_init_lowlevel(void)
> board_init_lowlevel_return();
> }
>
> -void board_init_lowlevel(void)
> +void reset(void)
> {
> u32 r;
>
> + common_reset();
> +
> if (get_pc() > 0x80000000)
> return;
>
> diff --git a/arch/arm/boards/phycard-i.MX27/lowlevel_init.S b/arch/arm/boards/phycard-i.MX27/lowlevel_init.S
> index c24edd4..b16afb5 100644
> --- a/arch/arm/boards/phycard-i.MX27/lowlevel_init.S
> +++ b/arch/arm/boards/phycard-i.MX27/lowlevel_init.S
> @@ -7,6 +7,7 @@
> #include <config.h>
> #include <mach/imx-regs.h>
> #include <mach/imx-pll.h>
> +#include <asm/barebox-arm-head.h>
>
> #define writel(val, reg) \
> ldr r0, =reg; \
> @@ -55,10 +56,9 @@
>
> .section ".text_bare_init","ax"
>
> -.globl board_init_lowlevel
> -board_init_lowlevel:
> -
> - mov r10, lr
> +.globl reset
> +reset:
> + common_reset r0
>
> /* ahb lite ip interface */
> writel(0x20040304, AIPI1_PSR0)
> @@ -72,7 +72,7 @@ board_init_lowlevel:
> cmp pc, #0xc0000000
> bhi 1f
>
> - mov pc,r10
> + b board_init_lowlevel_return
>
> 1:
> writel(IMX_PLL_PD(0) |
> @@ -121,5 +121,5 @@ copy_loop:
> #endif /* CONFIG_NAND_IMX_BOOT */
>
> ret:
> - mov pc,r10
> + b board_init_lowlevel_return
>
> diff --git a/arch/arm/boards/scb9328/lowlevel_init.S b/arch/arm/boards/scb9328/lowlevel_init.S
> index 5b02428..087e8e6 100644
> --- a/arch/arm/boards/scb9328/lowlevel_init.S
> +++ b/arch/arm/boards/scb9328/lowlevel_init.S
> @@ -19,6 +19,7 @@
> */
>
> #include <mach/imx-regs.h>
> +#include <asm/barebox-arm-head.h>
>
> #define CPU200
>
> @@ -81,10 +82,10 @@
> ldr r1, =val; \
> str r1, [r0];
>
> -.globl board_init_lowlevel
> -board_init_lowlevel:
> +.globl reset
> +reset:
>
> - mov r10, lr
> + common_reset r0
>
> /* Change PERCLK1DIV to 14 ie 14+1 */
> writel(CFG_PCDR_VAL, PCDR)
> @@ -156,7 +157,7 @@ board_init_lowlevel:
> cmp pc, #0x09000000
> bhi 1f
>
> - mov pc,r10
> + b board_init_lowlevel_return
>
> 1:
>
> @@ -181,4 +182,4 @@ board_init_lowlevel:
> writel(0x0, 0x08223000) /* CAS Latency 2, issue Mode Register Command, Burst Length = 8 */
> writel(0x810a8200, SDCTL0) /* Set to Normal Mode CAS 2 */
>
> - mov pc,r10
> + b board_init_lowlevel_return
> diff --git a/arch/arm/cpu/Makefile b/arch/arm/cpu/Makefile
> index 0ecc72e..f7ab276 100644
> --- a/arch/arm/cpu/Makefile
> +++ b/arch/arm/cpu/Makefile
> @@ -1,7 +1,7 @@
> obj-y += cpu.o
> obj-$(CONFIG_ARM_EXCEPTIONS) += exceptions.o
> obj-$(CONFIG_ARM_EXCEPTIONS) += interrupts.o
> -obj-y += start.o start-reset.o
> +obj-y += start.o
>
> #
> # Any variants can be called as start-armxyz.S
> @@ -19,4 +19,4 @@ obj-$(CONFIG_CPU_32v7) += cache-armv7.o
> pbl-$(CONFIG_CPU_32v7) += cache-armv7.o
> obj-$(CONFIG_CACHE_L2X0) += cache-l2x0.o
>
> -pbl-y += start-pbl.o start-reset.o
> +pbl-y += start-pbl.o
> diff --git a/arch/arm/cpu/start-pbl.c b/arch/arm/cpu/start-pbl.c
> index 932a3da..823b9cc 100644
> --- a/arch/arm/cpu/start-pbl.c
> +++ b/arch/arm/cpu/start-pbl.c
> @@ -41,6 +41,18 @@ void __naked __section(.text_head_entry) pbl_start(void)
> barebox_arm_head();
> }
>
> +/*
> + * The actual reset vector. This code is position independent and usually
> + * does not run at the address it's linked at.
> + */
> +#ifndef CONFIG_MACH_DO_LOWLEVEL_INIT
> +void __naked __bare_init reset(void)
> +{
> + common_reset();
> + board_init_lowlevel_return();
> +}
> +#endif
> +
> extern void *input_data;
> extern void *input_data_end;
>
> diff --git a/arch/arm/cpu/start-reset.c b/arch/arm/cpu/start-reset.c
> deleted file mode 100644
> index 46193ef..0000000
> --- a/arch/arm/cpu/start-reset.c
> +++ /dev/null
> @@ -1,63 +0,0 @@
> -/*
> - * start-reset.c
> - *
> - * Copyright (c) 2010 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
> - *
> - * See file CREDITS for list of people who contributed to this
> - * project.
> - *
> - * This program is free software; you can redistribute it and/or modify
> - * it under the terms of the GNU General Public License version 2
> - * as published by the Free Software Foundation.
> - *
> - * This program is distributed in the hope that it will be useful,
> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> - * GNU General Public License for more details.
> - *
> - * You should have received a copy of the GNU General Public License
> - * along with this program; if not, write to the Free Software
> - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
> - */
> -
> -#include <common.h>
> -#include <init.h>
> -#include <asm/system.h>
> -#include <asm/barebox-arm.h>
> -#include <asm/sections.h>
> -
> -/*
> - * The actual reset vector. This code is position independent and usually
> - * does not run at the address it's linked at.
> - */
> -void __naked __bare_init reset(void)
> -{
> - uint32_t r;
> -
> - /* set the cpu to SVC32 mode */
> - __asm__ __volatile__("mrs %0, cpsr":"=r"(r));
> - r &= ~0x1f;
> - r |= 0xd3;
> - __asm__ __volatile__("msr cpsr, %0" : : "r"(r));
> -
> - /* disable MMU stuff and caches */
> - r = get_cr();
> - r &= ~(CR_M | CR_C | CR_B | CR_S | CR_R | CR_V);
> - r |= CR_I;
> -
> -#if __LINUX_ARM_ARCH__ >= 6
> - r |= CR_U;
> -#else
> - r |= CR_A;
> -#endif
> -
> -#ifdef __ARMEB__
> - r |= CR_B;
> -#endif
> - set_cr(r);
> -
> -#ifdef CONFIG_MACH_DO_LOWLEVEL_INIT
> - board_init_lowlevel();
> -#endif
> - board_init_lowlevel_return();
> -}
> diff --git a/arch/arm/cpu/start.c b/arch/arm/cpu/start.c
> index 07e7dfe..e9a4620 100644
> --- a/arch/arm/cpu/start.c
> +++ b/arch/arm/cpu/start.c
> @@ -53,6 +53,18 @@ void __naked __section(.text_entry) start(void)
> }
>
> /*
> + * The actual reset vector. This code is position independent and usually
> + * does not run at the address it's linked at.
> + */
> +#ifndef CONFIG_MACH_DO_LOWLEVEL_INIT
> +void __naked __bare_init reset(void)
> +{
> + common_reset();
> + board_init_lowlevel_return();
> +}
> +#endif
> +
> +/*
> * Board code can jump here by either returning from board_init_lowlevel
> * or by calling this function directly.
> */
> diff --git a/arch/arm/include/asm/barebox-arm-head.h b/arch/arm/include/asm/barebox-arm-head.h
> index 0b1d786..eafad4e 100644
> --- a/arch/arm/include/asm/barebox-arm-head.h
> +++ b/arch/arm/include/asm/barebox-arm-head.h
> @@ -1,6 +1,37 @@
> #ifndef __ASM_ARM_HEAD_H
> #define __ASM_ARM_HEAD_H
>
> +#include <asm/system.h>
> +
> +#ifndef __ASSEMBLY__
> +
> +static inline void common_reset(void)
> +{
> + uint32_t r;
> +
> + /* set the cpu to SVC32 mode */
> + __asm__ __volatile__("mrs %0, cpsr":"=r"(r));
> + r &= ~0x1f;
> + r |= 0xd3;
> + __asm__ __volatile__("msr cpsr, %0" : : "r"(r));
> +
> + /* disable MMU stuff and caches */
> + r = get_cr();
> + r &= ~(CR_M | CR_C | CR_B | CR_S | CR_R | CR_V);
> + r |= CR_I;
> +
> +#if __LINUX_ARM_ARCH__ >= 6
> + r |= CR_U;
> +#else
> + r |= CR_A;
> +#endif
> +
> +#ifdef __ARMEB__
> + r |= CR_B;
> +#endif
> + set_cr(r);
> +}
> +
> #ifdef CONFIG_HAVE_MACH_ARM_HEAD
> #include <mach/barebox-arm-head.h>
> #else
> @@ -36,4 +67,41 @@ static inline void barebox_arm_head(void)
> }
> #endif
>
> +#else
> +
> +.macro common_reset, scratch
> +
> + /* set the cpu to SVC32 mode */
> + mrs \scratch, cpsr
> + bic \scratch, \scratch, #0x1f
> + orr \scratch, \scratch, #0xd3
> + msr cpsr, \scratch
> +
> +#if __LINUX_ARM_ARCH__ >= 7
> + isb
> +#elif __LINUX_ARM_ARCH__ == 6
> + mcr p15, 0, \scratch, c7, c5, 4
> +#endif
> +
> + /* disable MMU stuff and caches */
> + mrc p15, 0, \scratch, c1, c0, 0
> + bic \scratch, \scratch , #(CR_M | CR_C | CR_B)
> + bic \scratch, \scratch, #(CR_S | CR_R | CR_V)
> + orr \scratch, \scratch, #CR_I
> +
> +#if __LINUX_ARM_ARCH__ >= 6
> + orr \scratch, \scratch, #CR_U
> +#else
> + orr \scratch, \scratch, #CR_A
> +#endif
> +
> +#ifdef __ARMEB__
> + orr \scratch, \scratch, #CR_B
> +#endif
> +
> + mcr p15, 0, \scratch, c1, c0, 0
> +.endm
> +
> +#endif /* __ASSEMBLY__ */
> +
> #endif /* __ASM_ARM_HEAD_H */
> diff --git a/arch/arm/include/asm/system.h b/arch/arm/include/asm/system.h
> index 1d67492..26fb18c 100644
> --- a/arch/arm/include/asm/system.h
> +++ b/arch/arm/include/asm/system.h
> @@ -56,6 +56,7 @@
> #define CR_AFE (1 << 29) /* Access flag enable */
> #define CR_TE (1 << 30) /* Thumb exception enable */
>
> +#ifndef __ASSEMBLY__
> static inline unsigned int get_cr(void)
> {
> unsigned int val;
> @@ -69,4 +70,7 @@ static inline void set_cr(unsigned int val)
> : : "r" (val) : "cc");
> isb();
> }
> +
> +#endif
> +
> #endif /* __ASM_ARM_SYSTEM_H */
> diff --git a/arch/arm/mach-at91/at91rm9200_lowlevel_init.c b/arch/arm/mach-at91/at91rm9200_lowlevel_init.c
> index 5340bba..3ce3e67 100644
> --- a/arch/arm/mach-at91/at91rm9200_lowlevel_init.c
> +++ b/arch/arm/mach-at91/at91rm9200_lowlevel_init.c
> @@ -7,6 +7,7 @@
> #include <common.h>
> #include <asm/system.h>
> #include <asm/barebox-arm.h>
> +#include <asm/barebox-arm-head.h>
> #include <mach/hardware.h>
> #include <mach/at91rm9200.h>
> #include <mach/at91rm9200_mc.h>
> @@ -20,11 +21,13 @@ void static inline access_sdram(void)
> writel(0x00000000, AT91_SDRAM_BASE);
> }
>
> -void __naked __bare_init board_init_lowlevel(void)
> +void __naked __bare_init reset(void)
> {
> u32 r;
> int i;
>
> + common_reset();
> +
> /*
> * PMC Check if the PLL is already initialized
> */
> diff --git a/arch/arm/mach-at91/at91sam926x_lowlevel_init.c b/arch/arm/mach-at91/at91sam926x_lowlevel_init.c
> index 669f377..0ee0345 100644
> --- a/arch/arm/mach-at91/at91sam926x_lowlevel_init.c
> +++ b/arch/arm/mach-at91/at91sam926x_lowlevel_init.c
> @@ -8,6 +8,7 @@
> #include <common.h>
> #include <asm/system.h>
> #include <asm/barebox-arm.h>
> +#include <asm/barebox-arm-head.h>
> #include <mach/hardware.h>
> #include <mach/at91_pmc.h>
> #include <mach/at91_pio.h>
> @@ -33,11 +34,13 @@ static void inline pmc_check_mckrdy(void)
> } while (!(r & AT91_PMC_MCKRDY));
> }
>
> -void __naked __bare_init board_init_lowlevel(void)
> +void __naked __bare_init reset(void)
> {
> u32 r;
> int i;
>
> + common_reset();
> +
> at91_sys_write(AT91_WDT_MR, CONFIG_SYS_WDTC_WDMR_VAL);
>
> /* configure PIOx as EBI0 D[16-31] */
> diff --git a/arch/arm/mach-ep93xx/lowlevel_init.S b/arch/arm/mach-ep93xx/lowlevel_init.S
> index 27c2c90..07da8ae 100644
> --- a/arch/arm/mach-ep93xx/lowlevel_init.S
> +++ b/arch/arm/mach-ep93xx/lowlevel_init.S
> @@ -25,12 +25,11 @@
> */
>
> #include <mach/ep93xx-regs.h>
> +#include <asm/barebox-arm-head.h>
>
> -.globl board_init_lowlevel
> -board_init_lowlevel:
> - /* backup return address */
> - ldr r1, =SYSCON_SCRATCH0
> - str lr, [r1]
> +.globl reset
> +reset:
> + common_reset r0
>
> /* Turn on both LEDs */
> bl red_LED_on
> @@ -57,8 +56,4 @@ board_init_lowlevel:
> orr r0, r0, #0xc0000000
> mcr p15, 0, r0, c1, c0, 0
>
> - /* restore return address */
> - ldr r1, =SYSCON_SCRATCH0
> - ldr lr, [r1]
> -
> - mov pc, lr
> + b board_init_lowlevel_return
> diff --git a/arch/arm/mach-omap/Kconfig b/arch/arm/mach-omap/Kconfig
> index 9c76a96..c610a1f 100644
> --- a/arch/arm/mach-omap/Kconfig
> +++ b/arch/arm/mach-omap/Kconfig
> @@ -26,9 +26,6 @@ menu "OMAP Features"
> config MACH_OMAP
> bool
>
> -config OMAP3_LOWLEVEL_INIT
> - bool
> -
> choice
> prompt "Select OMAP Variant"
>
> @@ -36,7 +33,7 @@ config ARCH_OMAP3
> bool "OMAP3"
> select CPU_V7
> select GENERIC_GPIO
> - select OMAP3_LOWLEVEL_INIT
> + select MACH_HAS_LOWLEVEL_INIT
> select OMAP_CLOCK_SOURCE_S32K
> help
> Say Y here if you are using Texas Instrument's OMAP343x based platform
> diff --git a/arch/arm/mach-omap/omap3_core.S b/arch/arm/mach-omap/omap3_core.S
> index d1be6e5..7c31e1e 100644
> --- a/arch/arm/mach-omap/omap3_core.S
> +++ b/arch/arm/mach-omap/omap3_core.S
> @@ -40,8 +40,10 @@
> #include <mach/silicon.h>
> #include <mach/wdt.h>
> #include <mach/clocks.h>
> +#include <asm/barebox-arm-head.h>
>
> -ENTRY(board_init_lowlevel)
> +#ifdef CONFIG_MACH_DO_LOWLEVEL_INIT
> +ENTRY(reset)
> /* Invalidate all Dcaches */
> #ifndef CONFIG_CPU_V7_DCACHE_SKIP
> /* If Arch specific ROM code SMI handling does not exist */
> @@ -90,5 +92,6 @@ finished_inval:
> isb
> #endif /* CONFIG_CPU_V7_DCACHE_SKIP */
> /* back to arch calling code */
> - mov pc, lr
> -ENDPROC(board_init_lowlevel)
> + b board_init_lowlevel_return
> +ENDPROC(reset)
> +#endif
> --
> 1.7.10.4
>
>
> _______________________________________________
> barebox mailing list
> barebox@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
>
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2012-09-25 11:28 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2012-09-24 8:18 [PATCH 1/4] ARM OMAP: remove SRAM stack Jan Luebbe
2012-09-24 8:18 ` [PATCH 2/4] ARM OMAP3: rename arch_init_lowlevel to board_init_lowlevel Jan Luebbe
2012-09-24 8:18 ` [PATCH 3/4] ARM: remove ARCH_HAS_LOWLEVEL_INIT Jan Luebbe
2012-09-24 8:18 ` [PATCH 4/4] ARM: give boards control of the reset entry point Jan Luebbe
2012-09-25 11:28 ` Sascha Hauer
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox