mail archive of the barebox mailing list
 help / color / mirror / Atom feed
From: Andrey Smirnov <andrew.smirnov@gmail.com>
To: barebox@lists.infradead.org
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>, kernel@pengutronix.de
Subject: [PATCH] firmware: altera: Make nSTAT GPIO optional
Date: Wed, 31 Dec 2014 07:10:31 -0800	[thread overview]
Message-ID: <1420038631-8795-1-git-send-email-andrew.smirnov@gmail.com> (raw)

By taking parts of the programming handshaking protocol on faith it is
possible to make due with only two GPIO for programming Altera
FPGAs. This is not a very advisable practice, but sometime unavoidable
in GPIO constrained designs.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
---
 drivers/firmware/altera_serial.c | 59 ++++++++++++++++++++++++++++++----------
 1 file changed, 44 insertions(+), 15 deletions(-)

diff --git a/drivers/firmware/altera_serial.c b/drivers/firmware/altera_serial.c
index c5ffbb6..4527d27 100644
--- a/drivers/firmware/altera_serial.c
+++ b/drivers/firmware/altera_serial.c
@@ -25,6 +25,7 @@
 #include <fcntl.h>
 #include <fs.h>
 
+
 /*
  * Physical requirements:
  * - three free GPIOs for the signals nCONFIG, CONFIGURE_DONE, nSTATUS
@@ -67,13 +68,19 @@ static int altera_spi_open(struct firmware_handler *fh)
 	 * after about 2 µs the FPGA must acknowledge with
 	 * STATUS and CONFIG DONE lines at low level
 	 */
-	ret = wait_on_timeout(2 * USECOND,
+	if (gpio_is_valid(this->nstat_gpio)) {
+		ret = wait_on_timeout(2 * USECOND,
 				(gpio_get_value(this->nstat_gpio) == 0) &&
 				(gpio_get_value(this->confd_gpio) == 0));
+	} else {
+		ret = wait_on_timeout(2 * USECOND,
+				(gpio_get_value(this->confd_gpio) == 0));
+	}
+
 
 	if (ret != 0) {
 		dev_err(dev, "FPGA does not acknowledge the programming initiation\n");
-		if (gpio_get_value(this->nstat_gpio))
+		if (gpio_is_valid(this->nstat_gpio) && gpio_get_value(this->nstat_gpio))
 			dev_err(dev, "STATUS is still high!\n");
 		if (gpio_get_value(this->confd_gpio))
 			dev_err(dev, "CONFIG DONE is still high!\n");
@@ -90,11 +97,16 @@ static int altera_spi_open(struct firmware_handler *fh)
 	 * after about 1506 µs the FPGA must acknowledge this step
 	 * with the STATUS line at high level
 	 */
-	ret = wait_on_timeout(1600 * USECOND,
+
+	if (gpio_is_valid(this->nstat_gpio)) {
+		ret = wait_on_timeout(1600 * USECOND,
 				gpio_get_value(this->nstat_gpio) == 1);
-	if (ret != 0) {
-		dev_err(dev, "FPGA does not acknowledge the programming start\n");
-		return ret;
+		if (ret != 0) {
+			dev_err(dev, "FPGA does not acknowledge the programming start\n");
+			return ret;
+		}
+	} else {
+		udelay(1600);
 	}
 
 	dev_dbg(dev, "Initiating passed\n");
@@ -177,16 +189,24 @@ static int altera_spi_close(struct firmware_handler *fh)
 	 * when programming was successful,
 	 * both status lines should be at high level
 	 */
-	ret = wait_on_timeout(10 * USECOND,
+	if (gpio_is_valid(this->nstat_gpio)) {
+		ret = wait_on_timeout(10 * USECOND,
 				(gpio_get_value(this->nstat_gpio) == 1) &&
 				(gpio_get_value(this->confd_gpio) == 1));
+	} else {
+		ret = wait_on_timeout(10 * USECOND,
+				(gpio_get_value(this->confd_gpio) == 1));
+
+	}
+
 	if (ret == 0) {
 		dev_dbg(dev, "Programming successful\n");
 		return ret;
 	}
 
 	dev_err(dev, "Programming failed due to time out\n");
-	if (gpio_get_value(this->nstat_gpio) == 0)
+	if (gpio_is_valid(this->nstat_gpio) &&
+		gpio_get_value(this->nstat_gpio) == 0)
 		dev_err(dev, "STATUS is still low!\n");
 	if (gpio_get_value(this->confd_gpio) == 0)
 		dev_err(dev, "CONFIG DONE is still low!\n");
@@ -201,10 +221,15 @@ static int altera_spi_of(struct device_d *dev, struct fpga_spi *this)
 	int ret;
 
 	name = "nstat-gpio";
-	this->nstat_gpio = of_get_named_gpio(n, name, 0);
-	if (this->nstat_gpio < 0) {
-		ret = this->nstat_gpio;
-		goto out;
+	if (!of_get_property(n, name, NULL)) {
+		dev_info(dev, "nstat-gpio is not specified, assuming it is not connected\n");
+		this->nstat_gpio = -1;
+	} else {
+		this->nstat_gpio = of_get_named_gpio(n, name, 0);
+		if (this->nstat_gpio < 0) {
+			ret = this->nstat_gpio;
+			goto out;
+		}
 	}
 
 	name = "confd-gpio";
@@ -225,9 +250,13 @@ static int altera_spi_of(struct device_d *dev, struct fpga_spi *this)
 	ret = gpio_direction_output(this->nconfig_gpio, 1);
 	if (ret)
 		return ret;
-	ret = gpio_direction_input(this->nstat_gpio);
-	if (ret)
-		return ret;
+
+	if (gpio_is_valid(this->nstat_gpio)) {
+		ret = gpio_direction_input(this->nstat_gpio);
+		if (ret)
+			return ret;
+	}
+
 	ret = gpio_direction_input(this->confd_gpio);
 	if (ret)
 		return ret;
-- 
2.1.0


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

                 reply	other threads:[~2014-12-31 15:11 UTC|newest]

Thread overview: [no followups] expand[flat|nested]  mbox.gz  Atom feed

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1420038631-8795-1-git-send-email-andrew.smirnov@gmail.com \
    --to=andrew.smirnov@gmail.com \
    --cc=barebox@lists.infradead.org \
    --cc=kernel@pengutronix.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox