Re: MFGTools from NXP

[Ahmad Fatoum <a.fatoum@pengutronix.de>]

Hello,

On 10/17/19 10:40 AM, Mihaita Ivascu wrote:
> Yes I have tried with 2019.01.0 barebox but no change. On linux I
> cannot even connect with PUTTY even though /dev/ttyACM0 is present. On
> Windows at least I can connect via PUTTY

There's A Linux PuTTY client? Have you tried with a more traditional client,
e.g. screen or microcom?

> On both OSes fastboot does not list any device. But the board is
> detected in device manager/dmesg.

:/
I don't know why it doesn't work for you. I've used so far at least barebox
v2018.12.0, v2019.03.0 and v2019.09.0 on my i.MX6UL board and all were correctly
detected by the fastboot installed on my system (1:7.0.+r33-1 in debian 9.11).

If you want to debug it, you should start by looking into why the ttyACM
doesn't work for you.

Cheers
Ahmad


> 
> Best regards,
>          Mihaita Ivascu
> 
> On Wed, Oct 16, 2019 at 2:46 PM Ahmad Fatoum <a.fatoum@pengutronix.de> wrote:
>>
>> On 10/16/19 2:44 PM, Mihaita Ivascu wrote:
>>> 2018.04.0
>>
>> I've v2019.09.0 and did the same steps you described and it works for me.
>> Can you try with a newer version?
>>
>>>
>>> On Wed, Oct 16, 2019 at 2:41 PM Ahmad Fatoum <a.fatoum@pengutronix.de> wrote:
>>>>
>>>> On 10/16/19 2:35 PM, Mihaita Ivascu wrote:
>>>>> No it does not. Still no devices listed.
>>>>
>>>> Strange. What barebox version?
>>>>
>>>>>
>>>>> Thanks,
>>>>>       Mihaita
>>>>>
>>>>> On Wed, Oct 16, 2019 at 1:36 PM Ahmad Fatoum <a.fatoum@pengutronix.de> wrote:
>>>>>>
>>>>>> On 10/16/19 1:28 PM, Mihaita Ivascu wrote:
>>>>>>> On Wed, Oct 16, 2019 at 11:53 AM Ahmad Fatoum <a.fatoum@pengutronix.de>
>>>>>>> wrote:
>>>>>>>>
>>>>>>>>
>>>>>>>> On 10/16/19 11:48 AM, Mihaita Ivascu wrote:
>>>>>>>>> On Wed, Oct 16, 2019 at 11:26 AM Ahmad Fatoum <a.fatoum@pengutronix.de>
>>>>>>> wrote:
>>>>>>>>>>
>>>>>>>>>> On 10/16/19 11:21 AM, Mihaita Ivascu wrote:
>>>>>>>>>>> Hello,
>>>>>>>>>>>
>>>>>>>>>>>    Thanks for your answer. Yes i am able to connect via PUTTY to the
>>>>>>> target.
>>>>>>>>>>>    Then I should use some adb commands in order to push the new
>>>>>>>>>>> barebox/firmware ? do you know where I could find some examples?
>>>>>>>>>>
>>>>>>>>>> fastboot device -l works normally on Linux. You need to check what you
>>>>>>> need
>>>>>>>>>> to do on Windows to do the same. You should only need the Fastboot
>>>>>>> utility
>>>>>>>>>> for this.
>>>>>>>>>>
>>>>>>>>> [mi] Yes I have both fastboot and adb installed on both Windows and
>>>>>>>>> Linux machines. In both cases it does not list any device.
>>>>>>>>>        The board is detected as fastboot android is windows device
>>>>>>>>> manager. But the fastboot and adb does not list it. same for Linux.
>>>>>>>>> Please see attachment
>>>>>>>>
>>>>>>>> Let's focus on Linux. You don't see a device there?
>>>>>>>> What does barebox say? Does it say 'multi_bind: creating Fastboot
>>>>>>> function'?
>>>>>>>> What does you Linux host's dmesg say?
>>>>>>>>
>>>>>>>
>>>>>>> barebox@Phytec phyCORE-i.MX6 Ultra Lite SOM:/ usbgadget -aA
>>>>>>> udc0: registering UDC driver [g_multi]
>>>>>>> multi_bind: creating Fastboot function
>>>>>>> multi_bind: creating ACM function
>>>>>>> g_multi usbgadget: Multifunction Composite Gadget
>>>>>>> g_multi usbgadget: userspace failed to provide iSerialNumber
>>>>>>> g_multi usbgadget: g_multi ready
>>>>>>> barebox@Phytec phyCORE-i.MX6 Ultra Lite SOM:/ g_multi usbgadget: high-speed
>>>>>>> config #1: Multifunction Composite Gadget
>>>>>>>
>>>>>>> dmesg:
>>>>>>>
>>>>>>> [   25.602275] usb 1-1.3: USB disconnect, device number 3
>>>>>>> [   28.359930] usb 1-1.3: new high-speed USB device number 5 using ehci-pci
>>>>>>> [   28.452971] usb 1-1.3: New USB device found, idVendor=1d6b,
>>>>>>> idProduct=0104
>>>>>>> [   28.452976] usb 1-1.3: New USB device strings: Mfr=0, Product=2,
>>>>>>> SerialNumber=0
>>>>>>> [   28.452980] usb 1-1.3: Product: Phytec phyCORE-i.MX6 Ultra Lite SOM
>>>>>>> [   28.457925] cdc_acm 1-1.3:1.1: ttyACM0: USB ACM device
>>>>>>>
>>>>>>>
>>>>>>> So I see the device on Linux. But fastboot does not list any device on
>>>>>>> Linux.
>>>>>>
>>>>>> sudo doesn't change this?
>>>>>>
>>>>>>>
>>>>>>>>  >
>>>>>>>>>>>
>>>>>>>>>>>    Also I have a question: purpose of this activity is for me to be
>>>>>>>>>>> able to flash some imx6ul boards that have no firmware: no barebox.
>>>>>>>>>>>    So I know hardware config for the port is otg mode but as I have no
>>>>>>>>>>> barebox running them before I am wondering if I will be able to
>>>>>>>>>>> connect via PUTTY if I do not set the ACM gadget from barebox?
>>>>>>>>>>
>>>>>>>>>> Check the Embest MarS board's environment in barebox master. It sets up
>>>>>>>>>> a fastboot gadget automatically on boot from imx-usb-loader.
>>>>>>>>>> You can adjust it to your liking.
>>>>>>>>>
>>>>>>>>>   [mi] I was not able to find any docs about this board. I will keep
>>>>>>>>> searching/asking in the nxp community. If you have already ahve any
>>>>>>>>> files related to it would be helpful. Thanks
>>>>>>>>
>>>>>>>> It's in the barebox next branch (not master, sorry), see here:
>>>>>>>>
>>>>>>> https://github.com/saschahauer/barebox/blob/next/arch/arm/boards/embest-marsboard/defaultenv-mars/init/fastboot
>>>>>>>>
>>>>>>>> You can copy and adjust the environment setup for your board.
>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> Cheers
>>>>>>>>>> Ahmad
>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> Thanks,
>>>>>>>>>>>       Mihaita
>>>>>>>>>>>
>>>>>>>>>>> On Wed, Oct 16, 2019 at 10:51 AM Ahmad Fatoum <a.fatoum@pengutronix.de>
>>>>>>> wrote:
>>>>>>>>>>>>
>>>>>>>>>>>> On 10/16/19 10:40 AM, Mihaita Ivascu wrote:
>>>>>>>>>>>>> Hello again,
>>>>>>>>>>>>>
>>>>>>>>>>>>>    I have the target in otg peripheral mode, ADB and fastboot
>>>>>>> drivers
>>>>>>>>>>>>> installed but fastboot does not list any device. The board is
>>>>>>> detected
>>>>>>>>>>>>> in device manager
>>>>>>>>>>>>
>>>>>>>>>>>> Try enabling the ACM gadget in barebox and connect with PuTTY and
>>>>>>> see if
>>>>>>>>>>>> at least that works. It worked for me on Windows with another i.MX
>>>>>>> board
>>>>>>>>>>>> a month ago.
>>>>>>>>>>>>
>>>>>>>>>>>> As for fastboot, I don't know how to configure it on Windows, but
>>>>>>> surely
>>>>>>>>>>>> Android Modding boards will have you covered there.
>>>>>>>>>>>>
>>>>>>>>>>>>>    Please see attachment. Any ideas how should I proceed? Thanks for
>>>>>>>>>>>>> the support.
>>>>>>>>>>>>
>>>>>>>>>>>> You can enable the ACM gadget in barebox and see if that works, I
>>>>>>> tested
>>>>>>>>>>>> it on Windows with an i.MX board a month ago
>>>>>>>>>>>>
>>>>>>>>>>>> Cheers
>>>>>>>>>>>> Ahmad
>>>>>>>>>>>>
>>>>>>>>>>>>>
>>>>>>>>>>>>> Thanks,
>>>>>>>>>>>>>       Mihaita
>>>>>>>>>>>>>
>>>>>>>>>>>>> On Wed, Oct 16, 2019 at 9:32 AM Mihaita Ivascu
>>>>>>>>>>>>> <mihaita_ivascu@trimble.com> wrote:
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> Thanks. I have installed ADB and fastboot drivers for Win from
>>>>>>>>>>>>>>
>>>>>>> https://www.getdroidtips.com/how-to-install-adb-and-fastboot-on-windows/
>>>>>>>>>>>>>> I have installed according to the attachment.
>>>>>>>>>>>>>> But is not recognized in Windows. I did reboot the system after
>>>>>>>>>>>>>> installation but did not add any new env variable.
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> H:\>fastboot devices -l
>>>>>>>>>>>>>> 'fastboot' is not recognized as an internal or external command,
>>>>>>>>>>>>>> operable program or batch file.
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> Thanks,
>>>>>>>>>>>>>>       Mihaita
>>>>>>>>>>>>>>
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> On Tue, Oct 15, 2019 at 4:44 PM Ahmad Fatoum <
>>>>>>> a.fatoum@pengutronix.de> wrote:
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> On 10/15/19 4:41 PM, Mihaita Ivascu wrote:
>>>>>>>>>>>>>>>> barebox@Phytec phyCORE-i.MX6 Ultra Lite SOM:/ fastboot devices -l
>>>>>>>>>>>>>>> That's what you run on your host system, not on the target.
>>>>>>>>>>>>>>> --
>>>>>>>>>>>>>>> Pengutronix e.K.                           |
>>>>>>>         |
>>>>>>>>>>>>>>> Industrial Linux Solutions                 |
>>>>>>> http://www.pengutronix.de/  |
>>>>>>>>>>>>>>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone:
>>>>>>> +49-5121-206917-0    |
>>>>>>>>>>>>>>> Amtsgericht Hildesheim, HRA 2686           | Fax:
>>>>>>> +49-5121-206917-5555 |
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>> --
>>>>>>>>>>>> Pengutronix e.K.                           |
>>>>>>>     |
>>>>>>>>>>>> Industrial Linux Solutions                 |
>>>>>>> http://www.pengutronix.de/  |
>>>>>>>>>>>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone:
>>>>>>> +49-5121-206917-0    |
>>>>>>>>>>>> Amtsgericht Hildesheim, HRA 2686           | Fax:
>>>>>>> +49-5121-206917-5555 |
>>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> --
>>>>>>>>>> Pengutronix e.K.                           |
>>>>>>>   |
>>>>>>>>>> Industrial Linux Solutions                 | http://www.pengutronix.de/
>>>>>>>  |
>>>>>>>>>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0
>>>>>>>    |
>>>>>>>>>> Amtsgericht Hildesheim, HRA 2686           | Fax:
>>>>>>> +49-5121-206917-5555 |
>>>>>>>>
>>>>>>>> --
>>>>>>>> Pengutronix e.K.                           |                             |
>>>>>>>> Industrial Linux Solutions                 | http://www.pengutronix.de/  |
>>>>>>>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
>>>>>>>> Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
>>>>>>>
>>>>>>
>>>>>> --
>>>>>> Pengutronix e.K.                           |                             |
>>>>>> Industrial Linux Solutions                 | http://www.pengutronix.de/  |
>>>>>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
>>>>>> Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
>>>>>
>>>>
>>>>
>>>> --
>>>> Pengutronix e.K.                           |                             |
>>>> Industrial Linux Solutions                 | http://www.pengutronix.de/  |
>>>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
>>>> Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
>>>
>>
>>
>> --
>> Pengutronix e.K.                           |                             |
>> Industrial Linux Solutions                 | http://www.pengutronix.de/  |
>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
>> Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
> 


-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox