mail archive of the barebox mailing list
 help / color / mirror / Atom feed
From: Sascha Hauer <s.hauer@pengutronix.de>
To: barebox@lists.infradead.org
Subject: Re: [PATCH 1/2] Add Garz+Fricke Neso support
Date: Mon, 5 Jul 2010 11:43:23 +0200	[thread overview]
Message-ID: <20100705094323.GE26079@pengutronix.de> (raw)
In-Reply-To: <1278322711-4332-2-git-send-email-s.hauer@pengutronix.de>

On Mon, Jul 05, 2010 at 11:38:30AM +0200, Sascha Hauer wrote:
> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
> ---
>  arch/arm/Makefile         |    1 +
>  arch/arm/mach-imx/Kconfig |   10 +
>  board/guf-neso/Makefile   |    5 +
>  board/guf-neso/board.c    |  400 +++++++++++++++++++++++++++++++++++++++++++++
>  board/guf-neso/config.h   |   26 +++
>  board/guf-neso/env/config |   53 ++++++
>  board/guf-neso/lowlevel.c |  117 +++++++++++++
>  board/guf-neso/pll_init.S |   48 ++++++
>  8 files changed, 660 insertions(+), 0 deletions(-)
>  create mode 100644 board/guf-neso/Makefile
>  create mode 100644 board/guf-neso/board.c
>  create mode 100644 board/guf-neso/config.h
>  create mode 100644 board/guf-neso/env/config
>  create mode 100644 board/guf-neso/lowlevel.c
>  create mode 100644 board/guf-neso/pll_init.S
> 
> diff --git a/arch/arm/Makefile b/arch/arm/Makefile
> index 1c9f24e..ac8459c 100644
> --- a/arch/arm/Makefile
> +++ b/arch/arm/Makefile
> @@ -77,6 +77,7 @@ board-$(CONFIG_MACH_PCM038)			:= pcm038
>  board-$(CONFIG_MACH_PCM043)			:= pcm043
>  board-$(CONFIG_MACH_PM9263)			:= pm9263
>  board-$(CONFIG_MACH_SCB9328)			:= scb9328
> +board-$(CONFIG_MACH_NESO)			:= guf-neso
>  
>  machdirs := $(patsubst %,arch/arm/mach-%/,$(machine-y))
>  
> diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
> index 0cf6334..afee3d1 100644
> --- a/arch/arm/mach-imx/Kconfig
> +++ b/arch/arm/mach-imx/Kconfig
> @@ -16,6 +16,7 @@ config ARCH_TEXT_BASE
>  	default 0x87f00000 if MACH_PCM037
>  	default 0x87f00000 if MACH_PCM043
>  	default 0x08f80000 if MACH_SCB9328
> +	default 0xa7e00000 if MACH_NESO
>  
>  config BOARDINFO
>  	default "Eukrea CPUIMX25" if MACH_EUKREA_CPUIMX25
> @@ -30,6 +31,7 @@ config BOARDINFO
>  	default "Phytec phyCORE-i.MX31" if MACH_PCM037
>  	default "Phytec phyCORE-i.MX35" if MACH_PCM043
>  	default "Synertronixx scb9328" if MACH_SCB9328
> +	default "Garz+Fricke Neso" if MACH_NESO
>  
>  config ARCH_HAS_FEC_IMX
>  	bool
> @@ -195,6 +197,14 @@ config MACH_PCM038
>  	  Say Y here if you are using Phytec's phyCORE-i.MX27 (pcm038) equipped
>  	  with a Freescale i.MX27 Processor
>  
> +config MACH_NESO
> +	bool "Garz+Fricke Neso"
> +	select MACH_HAS_LOWLEVEL_INIT
> +	select HAVE_MMU
> +	help
> +	  Say Y here if you are using the Garz+Fricke Neso board equipped
> +	  with a Freescale i.MX27 Processor
> +
>  endchoice
>  
>  endif
> diff --git a/board/guf-neso/Makefile b/board/guf-neso/Makefile
> new file mode 100644
> index 0000000..2b6eb02
> --- /dev/null
> +++ b/board/guf-neso/Makefile
> @@ -0,0 +1,5 @@
> +
> +obj-y += lowlevel.o
> +obj-y += board.o
> +obj-y += pll_init.o
> +
> diff --git a/board/guf-neso/board.c b/board/guf-neso/board.c
> new file mode 100644
> index 0000000..d4aa8bb
> --- /dev/null
> +++ b/board/guf-neso/board.c
> @@ -0,0 +1,400 @@
> +/*
> + * Copyright (C) 2010 Sascha Hauer, Pengutronix
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + *
> + */
> +
> +#include <common.h>
> +#include <net.h>
> +#include <init.h>
> +#include <environment.h>
> +#include <fec.h>
> +#include <notifier.h>
> +#include <partition.h>
> +#include <fs.h>
> +#include <fcntl.h>
> +#include <nand.h>
> +#include <command.h>
> +#include <spi/spi.h>
> +#include <usb/isp1504.h>
> +
> +#include <asm/io.h>
> +#include <asm/mmu.h>
> +#include <asm/armlinux.h>
> +#include <asm/mach-types.h>
> +
> +#include <mach/gpio.h>
> +#include <mach/spi.h>
> +#include <mach/imx-regs.h>
> +#include <mach/iomux-mx27.h>
> +#include <mach/imx-nand.h>
> +#include <mach/imx-pll.h>
> +#include <mach/imxfb.h>
> +
> +/* two pins are controlling the CS signals to the USB phys */
> +#define USBH2_PHY_CS_GPIO (GPIO_PORTF + 20)
> +#define OTG_PHY_CS_GPIO (GPIO_PORTF + 19)
> +
> +/* two pins are controlling the display and its backlight */
> +#define LCD_POWER_GPIO (GPIO_PORTF + 18)
> +#define BACKLIGHT_POWER_GPIO (GPIO_PORTE + 5)
> +
> +static struct memory_platform_data ram_pdata = {
> +	.name = "ram0",
> +	.flags = DEVFS_RDWR,
> +};
> +
> +static struct device_d sdram_dev = {
> +	.name     = "mem",
> +	.map_base = 0xa0000000,
> +	.size     = 128 * 1024 * 1024,
> +	.platform_data = &ram_pdata,
> +};
> +
> +static struct fec_platform_data fec_info = {
> +	.xcv_type = MII100,
> +	.phy_addr = 31,
> +};
> +
> +static struct device_d fec_dev = {
> +	.name     = "fec_imx",
> +	.map_base = 0x1002b000,
> +	.platform_data	= &fec_info,
> +};
> +
> +static struct imx_nand_platform_data nand_info = {
> +	.width		= 1,
> +	.hw_ecc		= 1,
> +	.flash_bbt	= 1,
> +};
> +
> +static struct device_d nand_dev = {
> +	.name     = "imx_nand",
> +	.map_base = 0xd8000000,
> +	.platform_data	= &nand_info,
> +};
> +
> +static struct imx_fb_videomode imxfb_mode = {
> +	.mode = {
> +		.name		= "CPT CLAA070LC0JCT",
> +		.refresh	= 60,
> +		.xres		= 800,
> +		.yres		= 480,
> +		.pixclock	= KHZ2PICOS(27000),
> +		.hsync_len	= 1,	/* DE only sync */
> +		.left_margin	= 50,
> +		.right_margin	= 50,
> +		.vsync_len	= 1,	/* DE only sync */
> +		.upper_margin	= 10,
> +		.lower_margin	= 10,
> +	},
> +	/*
> +	 * - TFT style panel
> +	 * - clk enabled while idle
> +	 * - clock inverted
> +	 * - data not inverted
> +	 * - data enable high active
> +	 */
> +	.pcr = PCR_TFT |
> +		PCR_COLOR |
> +		PCR_PBSIZ_8 |
> +		PCR_BPIX_16 |
> +		PCR_CLKPOL |
> +		PCR_SCLK_SEL |
> +		PCR_LPPOL |
> +		PCR_FLMPOL,
> +	.bpp = 16,	/* TODO 32 bit does not work: The 'green' component is lacking in this mode */
> +};
> +
> +static void neso_fb_enable(int enable)
> +{
> +	gpio_direction_output(LCD_POWER_GPIO, enable);
> +	gpio_direction_output(BACKLIGHT_POWER_GPIO, enable);
> +}
> +
> +static struct imx_fb_platform_data neso_fb_data = {
> +	.mode	= &imxfb_mode,
> +	.pwmr	= 0x00000000,	/* doesn't matter */
> +	.lscr1	= 0x00120300,	/* doesn't matter */
> +	/* dynamic mode -> using the reset values (as recommended in the datasheet) */
> +	.dmacr	= (0 << 31) | (4 << 16) | 96,
> +	.enable	= neso_fb_enable,
> +	.framebuffer_ovl = (void *)0xa7f00000,
> +};
> +
> +static struct device_d imxfb_dev = {
> +	.name		= "imxfb",
> +	.map_base	= 0x10021000,
> +	.size		= 0x1000,
> +	.platform_data	= &neso_fb_data,
> +};
> +
> +#ifdef CONFIG_USB
> +
> +static struct device_d usbh2_dev = {
> +	.name     = "ehci",
> +	.map_base = IMX_OTG_BASE + 0x400,
> +	.size     = 0x200,
> +};
> +
> +static void neso_usbh_init(void)
> +{
> +	uint32_t temp;
> +
> +	temp = readl(IMX_OTG_BASE + 0x600);
> +	temp &= ~((3 << 21) | 1);
> +	temp |= (1 << 5) | (1 << 16) | (1 << 19) | (1 << 20) | (1<<11);
> +	writel(temp, IMX_OTG_BASE + 0x600);
> +
> +	temp = readl(IMX_OTG_BASE + 0x584);
> +	temp &= ~(3 << 30);
> +	temp |= 2 << 30;
> +	writel(temp, IMX_OTG_BASE + 0x584);
> +
> +	mdelay(10);
> +
> +	gpio_set_value(USBH2_PHY_CS_GPIO, 0);

Forgot a mdelay(10) here, will add while committing

> +	isp1504_set_vbus_power((void *)(IMX_OTG_BASE + 0x570), 1);
> +}
> +#endif
> +
> +#ifdef CONFIG_MMU
> +static void neso_mmu_init(void)
> +{
> +	mmu_init();
> +
> +	arm_create_section(0xa0000000, 0xa0000000, 128, PMD_SECT_DEF_CACHED);
> +	arm_create_section(0xb0000000, 0xa0000000, 128, PMD_SECT_DEF_UNCACHED);
> +
> +	setup_dma_coherent(0x10000000);
> +
> +#if TEXT_BASE & (0x100000 - 1)
> +#warning cannot create vector section. Adjust TEXT_BASE to a 1M boundary
> +#else
> +	arm_create_section(0x0,        TEXT_BASE,   1, PMD_SECT_DEF_UNCACHED);
> +#endif
> +	mmu_enable();
> +}
> +#else
> +static void neso_mmu_init(void)
> +{
> +}
> +#endif
> +
> +static int neso_devices_init(void)
> +{
> +	int i;
> +
> +	unsigned int mode[] = {
> +		/* UART1 */
> +		PE12_PF_UART1_TXD,
> +		PE13_PF_UART1_RXD,
> +		PE14_PF_UART1_CTS,
> +		PE15_PF_UART1_RTS,
> +		/* FEC */
> +		PD0_AIN_FEC_TXD0,
> +		PD1_AIN_FEC_TXD1,
> +		PD2_AIN_FEC_TXD2,
> +		PD3_AIN_FEC_TXD3,
> +		PD4_AOUT_FEC_RX_ER,
> +		PD5_AOUT_FEC_RXD1,
> +		PD6_AOUT_FEC_RXD2,
> +		PD7_AOUT_FEC_RXD3,
> +		PD8_AF_FEC_MDIO,
> +		PD9_AIN_FEC_MDC,
> +		PD10_AOUT_FEC_CRS,
> +		PD11_AOUT_FEC_TX_CLK,
> +		PD12_AOUT_FEC_RXD0,
> +		PD13_AOUT_FEC_RX_DV,
> +		PD14_AOUT_FEC_RX_CLK,
> +		PD15_AOUT_FEC_COL,
> +		PD16_AIN_FEC_TX_ER,
> +		PF23_AIN_FEC_TX_EN,
> +
> +		/* SSI1 connected in AC97 style */
> +		PC20_PF_SSI1_FS,
> +		PC21_PF_SSI1_RXD,
> +		PC22_PF_SSI1_TXD,
> +		PC23_PF_SSI1_CLK,
> +
> +		/* LED 1 */
> +		(GPIO_PORTB | 15 | GPIO_GPIO | GPIO_OUT),
> +		/* LED 2 */
> +		(GPIO_PORTB | 16 | GPIO_GPIO | GPIO_OUT),
> +		/* CTOUCH reset */
> +		(GPIO_PORTB | 17 | GPIO_GPIO | GPIO_OUT),
> +		/* CTOUCH IRQ */
> +		(GPIO_PORTB | 14 | GPIO_GPIO | GPIO_IN),
> +		/* RTC IRQ */
> +		(GPIO_PORTF | 14 | GPIO_GPIO | GPIO_IN),
> +		/* SD change card detection */
> +		(GPIO_PORTF | 17 | GPIO_GPIO | GPIO_IN),
> +		/* SDHC1*/
> +		PE18_PF_SD1_D0,
> +		PE19_PF_SD1_D1,
> +		PE20_PF_SD1_D2,
> +		PE21_PF_SD1_D3,
> +		PE22_PF_SD1_CMD,
> +		PE23_PF_SD1_CLK,
> +		/* I2C1 */
> +		PD17_PF_I2C_DATA,
> +		PD18_PF_I2C_CLK,
> +		/* I2C2, for CTOUCH */
> +		PC5_PF_I2C2_SDA,
> +		PC6_PF_I2C2_SCL,
> +
> +		/* Connected to: Both USB phys and ethernet phy FIXME 1 = RESET? */
> +		PE17_PF_RESET_OUT,
> +
> +		/* USB host */
> +		(USBH2_PHY_CS_GPIO | GPIO_GPIO | GPIO_OUT),
> +		PA0_PF_USBH2_CLK,
> +		PA1_PF_USBH2_DIR,
> +		PA3_PF_USBH2_NXT,
> +		PA4_PF_USBH2_STP,
> +		PD22_AF_USBH2_DATA0,
> +		PD24_AF_USBH2_DATA1,
> +		PD23_AF_USBH2_DATA2,
> +		PD20_AF_USBH2_DATA3,
> +		PD19_AF_USBH2_DATA4,
> +		PD26_AF_USBH2_DATA5,
> +		PD21_AF_USBH2_DATA6,
> +		PA2_PF_USBH2_DATA7,
> +
> +		/* USB OTG */
> +		(OTG_PHY_CS_GPIO | GPIO_GPIO | GPIO_OUT),
> +		PE24_PF_USBOTG_CLK,
> +		PE2_PF_USBOTG_DIR,
> +		PE0_PF_USBOTG_NXT,
> +		PE1_PF_USBOTG_STP,
> +		PC9_PF_USBOTG_DATA0,
> +		PC11_PF_USBOTG_DATA1,
> +		PC10_PF_USBOTG_DATA2,
> +		PC13_PF_USBOTG_DATA3,
> +		PC12_PF_USBOTG_DATA4,
> +		PC7_PF_USBOTG_DATA5,
> +		PC8_PF_USBOTG_DATA6,
> +		PE25_PF_USBOTG_DATA7,
> +
> +		/* Display signals */
> +		(LCD_POWER_GPIO | GPIO_GPIO | GPIO_OUT), /* LCD power: 1 = LCD on */
> +		PA5_PF_LSCLK,
> +		PA6_PF_LD0,
> +		PA7_PF_LD1,
> +		PA8_PF_LD2,
> +		PA9_PF_LD3,
> +		PA10_PF_LD4,
> +		PA11_PF_LD5,
> +		PA12_PF_LD6,
> +		PA13_PF_LD7,
> +		PA14_PF_LD8,
> +		PA15_PF_LD9,
> +		PA16_PF_LD10,
> +		PA17_PF_LD11,
> +		PA18_PF_LD12,
> +		PA19_PF_LD13,
> +		PA20_PF_LD14,
> +		PA21_PF_LD15,
> +		PA22_PF_LD16,
> +		PA23_PF_LD17,
> +		PA31_PF_OE_ACD,	/* DE */
> +
> +		/* Backlight PWM (Use as gpio) */
> +		(BACKLIGHT_POWER_GPIO | GPIO_GPIO | GPIO_OUT),
> +	};
> +
> +	/* reset the chip select lines to the USB/OTG phys to avoid any hang */
> +	gpio_direction_output(OTG_PHY_CS_GPIO, 1);
> +	gpio_direction_output(USBH2_PHY_CS_GPIO, 1);
> +
> +
> +	neso_mmu_init();
> +
> +	/* initialize gpios */
> +	for (i = 0; i < ARRAY_SIZE(mode); i++)
> +		imx_gpio_mode(mode[i]);
> +
> +	register_device(&nand_dev);
> +	register_device(&sdram_dev);
> +	register_device(&imxfb_dev);
> +
> +#ifdef CONFIG_USB
> +	neso_usbh_init();
> +	register_device(&usbh2_dev);
> +#endif
> +
> +	register_device(&fec_dev);
> +
> +	devfs_add_partition("nand0", 0x00000, 0x40000, PARTITION_FIXED, "self_raw");
> +	dev_add_bb_dev("self_raw", "self0");
> +
> +	devfs_add_partition("nand0", 0x40000, 0x80000, PARTITION_FIXED, "env_raw");
> +	dev_add_bb_dev("env_raw", "env0");
> +
> +	armlinux_add_dram(&sdram_dev);
> +	armlinux_set_bootparams((void *)0xa0000100);
> +	armlinux_set_architecture(MACH_TYPE_NESO);
> +
> +	return 0;
> +}
> +
> +device_initcall(neso_devices_init);
> +
> +static struct device_d neso_serial_device = {
> +	.name     = "imx_serial",
> +	.map_base = IMX_UART1_BASE,
> +	.size     = 4096,
> +};
> +
> +static int neso_console_init(void)
> +{
> +	register_device(&neso_serial_device);
> +
> +	return 0;
> +}
> +
> +console_initcall(neso_console_init);
> +
> +extern void *neso_pll_init, *neso_pll_init_end;
> +
> +static int neso_pll(void)
> +{
> +	void *vram = (void *)0xffff4c00;
> +	void (*pllfunc)(void) = vram;
> +
> +	printf("initialising PLLs\n");
> +
> +	memcpy(vram, &neso_pll_init, 0x100);
> +
> +	console_flush();
> +
> +	pllfunc();
> +
> +	/* clock gating enable */
> +	GPCR = 0x00050f08;
> +
> +	PCDR0 = 0x130410c3;
> +	PCDR1 = 0x09030911;
> +
> +	/* Clocks have changed. Notify clients */
> +	clock_notifier_call_chain();
> +
> +	return 0;
> +}
> +
> +late_initcall(neso_pll);
> +
> diff --git a/board/guf-neso/config.h b/board/guf-neso/config.h
> new file mode 100644
> index 0000000..c2f5e7c
> --- /dev/null
> +++ b/board/guf-neso/config.h
> @@ -0,0 +1,26 @@
> +/*
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +/**
> + * @file
> + * @brief Global defintions for the ARM i.MX27 based pcm038
> + */
> +
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +#endif	/* __CONFIG_H */
> diff --git a/board/guf-neso/env/config b/board/guf-neso/env/config
> new file mode 100644
> index 0000000..6327e69
> --- /dev/null
> +++ b/board/guf-neso/env/config
> @@ -0,0 +1,53 @@
> +#!/bin/sh
> +
> +machine=guf-neso
> +eth0.serverip=
> +user=
> +
> +# use 'dhcp' to do dhcp in barebox and in kernel
> +# use 'none' if you want to skip kernel ip autoconfiguration
> +ip=dhcp
> +
> +# or set your networking parameters here
> +#eth0.ipaddr=a.b.c.d
> +#eth0.netmask=a.b.c.d
> +#eth0.gateway=a.b.c.d
> +#eth0.serverip=a.b.c.d
> +
> +# can be either 'net', 'nor' or 'nand'
> +kernel_loc=net
> +# can be either 'net', 'nor', 'nand' or 'initrd'
> +rootfs_loc=net
> +
> +# can be either 'jffs2' or 'ubifs'
> +rootfs_type=ubifs
> +rootfsimage=root-$machine.$rootfs_type
> +
> +# The image type of the kernel. Can be uimage, zimage, raw, or raw_lzo
> +kernelimage_type=zimage
> +kernelimage=zImage-$machine
> +#kernelimage_type=uimage
> +#kernelimage=uImage-$machine
> +#kernelimage_type=raw
> +#kernelimage=Image-$machine
> +#kernelimage_type=raw_lzo
> +#kernelimage=Image-$machine.lzo
> +
> +if [ -n $user ]; then
> +	kernelimage="$user"-"$kernelimage"
> +	nfsroot="$eth0.serverip:/home/$user/nfsroot/$machine"
> +	rootfsimage="$user"-"$rootfsimage"
> +else
> +	nfsroot="$eth0.serverip:/path/to/nfs/root"
> +fi
> +
> +autoboot_timeout=3
> +
> +bootargs="console=ttymxc0,115200"
> +
> +nand_parts="256k(barebox)ro,512k(bareboxenv),2M(kernel),-(root)"
> +rootfs_mtdblock_nand=3
> +
> +# set a fancy prompt (if support is compiled in)
> +PS1="\e[1;32mbarebox@\e[1;31m\h:\w\e[0m "
> +
> diff --git a/board/guf-neso/lowlevel.c b/board/guf-neso/lowlevel.c
> new file mode 100644
> index 0000000..0c376f2
> --- /dev/null
> +++ b/board/guf-neso/lowlevel.c
> @@ -0,0 +1,117 @@
> +/*
> + *
> + * (c) 2007 Pengutronix, Sascha Hauer <s.hauer@pengutronix.de>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +#include <common.h>
> +#include <init.h>
> +#include <mach/imx-regs.h>
> +#include <mach/imx-pll.h>
> +#include <mach/esdctl.h>
> +#include <asm/cache-l2x0.h>
> +#include <asm/io.h>
> +#include <mach/imx-nand.h>
> +#include <asm/barebox-arm.h>
> +#include <asm/system.h>
> +#include <asm-generic/memory_layout.h>
> +
> +static void __bare_init __naked insdram(void)
> +{
> +	uint32_t r;
> +
> +	PCCR1 |= PCCR1_NFC_BAUDEN;
> +
> +	/* setup a stack to be able to call imx_nand_load_image() */
> +	r = STACK_BASE + STACK_SIZE - 12;
> +	__asm__ __volatile__("mov sp, %0" : : "r"(r));
> +
> +	imx_nand_load_image((void *)TEXT_BASE, 256 * 1024);
> +
> +	board_init_lowlevel_return();
> +}
> +
> +#define ESDCTL0_VAL (ESDCTL0_SDE | ESDCTL0_ROW13 | ESDCTL0_COL10)
> +
> +void __bare_init __naked board_init_lowlevel(void)
> +{
> +	uint32_t r;
> +	int i;
> +	unsigned int *trg, *src;
> +
> +	/* ahb lite ip interface */
> +	AIPI1_PSR0 = 0x20040304;
> +	AIPI1_PSR1 = 0xDFFBFCFB;
> +	AIPI2_PSR0 = 0x00000000;
> +	AIPI2_PSR1 = 0xFFFFFFFF;
> +
> +	/* Skip SDRAM initialization if we run from RAM */
> +	r = get_pc();
> +	if (r > 0xa0000000 && r < 0xb0000000)
> +		board_init_lowlevel_return();
> +
> +	/*
> +	 * DDR on CSD0
> +	 */
> +	writel(0x00000008, ESDMISC); /* Enable DDR SDRAM operation */
> +
> +	DSCR(3) = 0x55555555; /* Set the driving strength   */
> +	DSCR(5) = 0x55555555;
> +	DSCR(6) = 0x55555555;
> +	DSCR(7) = 0x00005005;
> +	DSCR(8) = 0x15555555;
> +
> +	writel(0x00000004, ESDMISC); /* Initial reset */
> +	writel(0x006ac73a, ESDCFG0);
> +
> +	writel(ESDCTL0_VAL | ESDCTL0_SMODE_PRECHARGE, ESDCTL0); /* precharge CSD0 all banks */
> +	writel(0x00000000, 0xA0000F00);	/* CSD0 precharge address (A10 = 1) */
> +	writel(ESDCTL0_VAL | ESDCTL0_SMODE_AUTO_REFRESH, ESDCTL0);
> +
> +	for (i = 0; i < 8; i++)
> +		writel(0, 0xa0000f00);
> +
> +	writel(ESDCTL0_VAL | ESDCTL0_SMODE_LOAD_MODE, ESDCTL0);
> +
> +	writeb(0xda, 0xa0000033);
> +	writeb(0xff, 0xa1000000);
> +	writel(ESDCTL0_VAL | ESDCTL0_DSIZ_31_0 | ESDCTL0_REF4 |
> +			ESDCTL0_BL | ESDCTL0_SMODE_NORMAL, ESDCTL0);
> +
> +#ifdef CONFIG_NAND_IMX_BOOT
> +	/* skip NAND boot if not running from NFC space */
> +	r = get_pc();
> +	if (r < IMX_NFC_BASE || r > IMX_NFC_BASE + 0x800)
> +		board_init_lowlevel_return();
> +
> +	src = (unsigned int *)IMX_NFC_BASE;
> +	trg = (unsigned int *)TEXT_BASE;
> +
> +	/* Move ourselves out of NFC SRAM */
> +	for (i = 0; i < 0x800 / sizeof(int); i++)
> +		*trg++ = *src++;
> +
> +	/* Jump to SDRAM */
> +	r = (unsigned int)&insdram;
> +	__asm__ __volatile__("mov pc, %0" : : "r"(r));
> +#else
> +	board_init_lowlevel_return();
> +#endif
> +}
> +
> diff --git a/board/guf-neso/pll_init.S b/board/guf-neso/pll_init.S
> new file mode 100644
> index 0000000..87e5312
> --- /dev/null
> +++ b/board/guf-neso/pll_init.S
> @@ -0,0 +1,48 @@
> +#include <config.h>
> +#include <mach/imx-regs.h>
> +#include <mach/imx-pll.h>
> +#include <linux/linkage.h>
> +
> +#define writel(val, reg) \
> +	ldr		r0,	=reg;	\
> +	ldr		r1,	=val;	\
> +	str		r1,   [r0];
> +
> +#define CSCR_VAL CSCR_USB_DIV(3) |	\
> +		 CSCR_SD_CNT(3) |	\
> +		 CSCR_MSHC_SEL |	\
> +		 CSCR_H264_SEL |	\
> +		 CSCR_SSI1_SEL |	\
> +		 CSCR_SSI2_SEL |	\
> +		 CSCR_MCU_SEL |		\
> +		 CSCR_ARM_SRC_MPLL |	\
> +		 CSCR_SP_SEL |		\
> +		 CSCR_ARM_DIV(0) |	\
> +		 CSCR_FPM_EN |		\
> +		 CSCR_SPEN |		\
> +		 CSCR_MPEN |		\
> +		 CSCR_AHB_DIV(1)
> +
> +ENTRY(neso_pll_init)
> +
> +	writel(IMX_PLL_PD(0) |
> +		 IMX_PLL_MFD(51) |
> +		 IMX_PLL_MFI(7) |
> +		 IMX_PLL_MFN(35), MPCTL0) /* 399 MHz */
> +
> +	writel(IMX_PLL_PD(1) |
> +		 IMX_PLL_MFD(12) |
> +		 IMX_PLL_MFI(9) |
> +		 IMX_PLL_MFN(3), SPCTL0) /* SPLL = 2 * 26 * 4.61538 MHz = 240 MHz */
> +
> +	writel(CSCR_VAL | CSCR_MPLL_RESTART | CSCR_SPLL_RESTART, CSCR)
> +
> +	ldr r2, =16000
> +1:
> +	subs    r2, r2, #1
> +	nop
> +	bcs 1b
> +
> +	mov     pc, lr
> +ENDPROC(neso_pll_init)
> +
> -- 
> 1.7.1
> 
> 

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

  reply	other threads:[~2010-07-05  9:43 UTC|newest]

Thread overview: 4+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2010-07-05  9:38 Garz+Fricke Neso Support Sascha Hauer
2010-07-05  9:38 ` [PATCH 1/2] Add Garz+Fricke Neso support Sascha Hauer
2010-07-05  9:43   ` Sascha Hauer [this message]
2010-07-05  9:38 ` [PATCH 2/2] Add Garz+Fricke Neso defconfig Sascha Hauer

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20100705094323.GE26079@pengutronix.de \
    --to=s.hauer@pengutronix.de \
    --cc=barebox@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox