From: Sascha Hauer <s.hauer@pengutronix.de>
To: Vicente Bergas <vicencb@gmail.com>
Cc: barebox@lists.infradead.org
Subject: Re: [PATCH 6/6] OMAP4: clean voltage switch
Date: Mon, 15 Oct 2012 09:17:48 +0200 [thread overview]
Message-ID: <20121015071748.GK27665@pengutronix.de> (raw)
In-Reply-To: <1350260560-15528-7-git-send-email-vicencb@gmail.com>
On Mon, Oct 15, 2012 at 02:22:40AM +0200, Vicente Bergas wrote:
> Modified voltage setting to do a clean switch.
> See: http://lists.denx.de/pipermail/u-boot/2012-March/119149.html
Could you include the commit message from the original U-Boot commit?
Having a reference to the mailing list is fine, but we should also have
the reasoning behind this patch in the commit log.
Sascha
>
> Also changed vdd_mpu and VCORE2 to 1.2 volt as in u-boot.
>
> Signed-off-by: Vicente Bergas <vicencb@gmail.com>
> ---
> arch/arm/boards/archosg9/mux.c | 9 +----
> arch/arm/mach-omap/include/mach/omap4-clock.h | 2 +-
> arch/arm/mach-omap/include/mach/omap4-silicon.h | 2 +-
> arch/arm/mach-omap/omap4_clock.c | 37 +++++++++++++++++-
> arch/arm/mach-omap/omap4_generic.c | 52 ++++---------------------
> 5 files changed, 46 insertions(+), 56 deletions(-)
>
> diff --git a/arch/arm/boards/archosg9/mux.c b/arch/arm/boards/archosg9/mux.c
> index 7ca5057..c8695c0 100644
> --- a/arch/arm/boards/archosg9/mux.c
> +++ b/arch/arm/boards/archosg9/mux.c
> @@ -441,7 +441,7 @@ static const struct pad_conf_entry wkup_padconf_array[] = {
> /* gpio_wk30 */
> { FREF_CLK3_REQ , M3 },
> /* gpio_wk7 */ /* tps62361_vsel0 */
> - { FREF_CLK4_REQ , IEN | PTU | M3 },
> + { FREF_CLK4_REQ , M3 },
> };
>
> void set_muxconf_regs(void){
> @@ -449,11 +449,4 @@ void set_muxconf_regs(void){
> core_padconf_array, ARRAY_SIZE(core_padconf_array));
> omap4_do_set_mux(OMAP44XX_CONTROL_PADCONF_WKUP,
> wkup_padconf_array, ARRAY_SIZE(wkup_padconf_array));
> -
> - /* gpio_wk7 is used for controlling TPS on 4460 */
> - if (omap4_revision() >= OMAP4460_ES1_0) {
> - writew(M3, OMAP44XX_CONTROL_PADCONF_WKUP + FREF_CLK4_REQ);
> - /* Enable GPIO-1 clocks before TPS initialization */
> - omap4_enable_gpio1_wup_clocks();
> - }
> }
> diff --git a/arch/arm/mach-omap/include/mach/omap4-clock.h b/arch/arm/mach-omap/include/mach/omap4-clock.h
> index e5302d6..8cbc061 100644
> --- a/arch/arm/mach-omap/include/mach/omap4-clock.h
> +++ b/arch/arm/mach-omap/include/mach/omap4-clock.h
> @@ -335,5 +335,5 @@ void omap4_lock_core_dpll_shadow(const struct dpll_param *param);
> void omap4_enable_gpio1_wup_clocks(void);
> void omap4_enable_gpio_clocks(void);
> void omap4_enable_all_clocks(void);
> -void omap4_do_scale_tps62361(u32 reg, u32 volt_mv);
> +void omap4_do_scale_tps62361(int vsel0_pin, u32 reg, u32 volt_mv);
>
> diff --git a/arch/arm/mach-omap/include/mach/omap4-silicon.h b/arch/arm/mach-omap/include/mach/omap4-silicon.h
> index 71ffe39..137cc88 100644
> --- a/arch/arm/mach-omap/include/mach/omap4-silicon.h
> +++ b/arch/arm/mach-omap/include/mach/omap4-silicon.h
> @@ -196,6 +196,6 @@ struct dpll_param;
> void omap4_ddr_init(const struct ddr_regs *, const struct dpll_param *);
> void omap4_power_i2c_send(u32);
> unsigned int omap4_revision(void);
> -noinline int omap4_scale_vcores(unsigned vsel0_pin);
> +noinline int omap4_scale_vcores(int vsel0_pin);
>
> #endif
> diff --git a/arch/arm/mach-omap/omap4_clock.c b/arch/arm/mach-omap/omap4_clock.c
> index 1481f16..f7927d2 100644
> --- a/arch/arm/mach-omap/omap4_clock.c
> +++ b/arch/arm/mach-omap/omap4_clock.c
> @@ -394,9 +394,38 @@ void omap4_enable_all_clocks(void)
> sr32(CM_L3INIT_USBPHY_CLKCTRL, 0, 32, 0x301);
> }
>
> -void omap4_do_scale_tps62361(u32 reg, u32 volt_mv)
> +#define GPIO_MASK 0x1f
> +#define GPIO_OE 0x34
> +#define GPIO_CLEARDATAOUT 0x90
> +#define GPIO_SETDATAOUT 0x94
> +
> +static void __iomem *omap4_get_gpio_base(unsigned gpio)
> +{
> + void __iomem *base;
> +
> + if (gpio < 32)
> + base = (void *)0x4a310100;
> + else
> + base = (void *)(0x48053100 + ((gpio & ~GPIO_MASK) << 8));
> +
> + return base;
> +}
> +
> +void omap4_do_scale_tps62361(int vsel0_pin, u32 reg, u32 volt_mv)
> {
> u32 temp, step;
> + void __iomem *base;
> + u32 val;
> +
> + /* Pull the GPIO low to select SET0 register, while we program SET1 */
> + if (vsel0_pin >= 0) {
> + base = omap4_get_gpio_base(vsel0_pin);
> + val = 1 << (vsel0_pin & GPIO_MASK);
> + writel(val, base + GPIO_CLEARDATAOUT);
> + val = readl(base + GPIO_OE);
> + val &= (1 << (vsel0_pin & GPIO_MASK));
> + writel(val, base + GPIO_OE);
> + }
>
> step = volt_mv - TPS62361_BASE_VOLT_MV;
> step /= 10;
> @@ -411,4 +440,10 @@ void omap4_do_scale_tps62361(u32 reg, u32 volt_mv)
> if (!wait_on_value(OMAP44XX_PRM_VC_VAL_BYPASS_VALID_BIT, 0,
> OMAP44XX_PRM_VC_VAL_BYPASS, LDELAY))
> puts("Scaling voltage failed for vdd_mpu from TPS\n");
> +
> + /* Pull the GPIO high to select SET1 register */
> + if (vsel0_pin >= 0) {
> + val = 1 << (vsel0_pin & GPIO_MASK);
> + writel(val, base + GPIO_SETDATAOUT);
> + }
> }
> diff --git a/arch/arm/mach-omap/omap4_generic.c b/arch/arm/mach-omap/omap4_generic.c
> index 765fcb5..8e692ba 100644
> --- a/arch/arm/mach-omap/omap4_generic.c
> +++ b/arch/arm/mach-omap/omap4_generic.c
> @@ -495,27 +495,11 @@ enum omap_boot_src omap4_bootsrc(void)
> return OMAP_BOOTSRC_UNKNOWN;
> }
>
> -#define GPIO_MASK 0x1f
> -
> -static void __iomem *omap4_get_gpio_base(unsigned gpio)
> -{
> - void __iomem *base;
> -
> - if (gpio < 32)
> - base = (void *)0x4a310000;
> - else
> - base = (void *)(0x48053000 + ((gpio & ~GPIO_MASK) << 8));
> -
> - return base;
> -}
> -
> #define I2C_SLAVE 0x12
>
> -noinline int omap4_scale_vcores(unsigned vsel0_pin)
> +noinline int omap4_scale_vcores(int vsel0_pin)
> {
> - void __iomem *base;
> unsigned int rev = omap4_revision();
> - u32 val = 0;
>
> /* For VC bypass only VCOREx_CGF_FORCE is necessary and
> * VCOREx_CFG_VOLTAGE changes can be discarded
> @@ -523,33 +507,6 @@ noinline int omap4_scale_vcores(unsigned vsel0_pin)
> writel(0, OMAP44XX_PRM_VC_CFG_I2C_MODE);
> writel(0x6026, OMAP44XX_PRM_VC_CFG_I2C_CLK);
>
> - /* TPS - supplies vdd_mpu on 4460 */
> - if (rev >= OMAP4460_ES1_0) {
> - /*
> - * Setup SET1 and SET0 with right values so that kernel
> - * can use either of them based on its needs.
> - */
> - omap4_do_scale_tps62361(TPS62361_REG_ADDR_SET0, 1430);
> - omap4_do_scale_tps62361(TPS62361_REG_ADDR_SET1, 1430);
> -
> - /*
> - * Select SET1 in TPS62361:
> - * VSEL1 is grounded on board. So the following selects
> - * VSEL1 = 0 and VSEL0 = 1
> - */
> - base = omap4_get_gpio_base(vsel0_pin);
> -
> - val = 1 << (vsel0_pin & GPIO_MASK);
> - writel(val, base + 0x190);
> -
> - val = readl(base + 0x134);
> - val &= (1 << (vsel0_pin & GPIO_MASK));
> - writel(val, base + 0x134);
> -
> - val = 1 << (vsel0_pin & GPIO_MASK);
> - writel(val, base + 0x194);
> - }
> -
> /* set VCORE1 force VSEL */
> /*
> * 4430 : supplies vdd_mpu
> @@ -568,8 +525,13 @@ noinline int omap4_scale_vcores(unsigned vsel0_pin)
> /* 0x55: i2c addr, 28: ~ 1200 mvolts*/
> omap4_power_i2c_send((0x2855 << 8) | I2C_SLAVE);
>
> + /* TPS - supplies vdd_mpu on 4460 */
> + if (rev >= OMAP4460_ES1_0)
> + omap4_do_scale_tps62361(vsel0_pin,
> + TPS62361_REG_ADDR_SET1, 1203);
> +
> /* FIXME: set VCORE2 force VSEL, Check the reset value */
> - omap4_power_i2c_send((0x295B << 8) | I2C_SLAVE);
> + omap4_power_i2c_send((0x285B << 8) | I2C_SLAVE);
>
> /* set VCORE3 force VSEL */
> switch (rev) {
> --
> 1.7.12.3
>
>
> _______________________________________________
> barebox mailing list
> barebox@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
>
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
next prev parent reply other threads:[~2012-10-15 7:17 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-10-15 0:22 [PATCH 0/6] archosg9: improve support for tablet Vicente Bergas
2012-10-15 0:22 ` [PATCH 1/6] ArchosG9: changed serial port and env Vicente Bergas
2012-10-15 0:22 ` [PATCH 2/6] ARM: add rename PSR bits to match linux names Vicente Bergas
2012-10-15 0:22 ` [PATCH 3/6] ARM: ensure irqs are disabled at barebox exit Vicente Bergas
2012-10-15 0:22 ` [PATCH 4/6] UIMAGE: improve transfer speed Vicente Bergas
2012-10-15 0:22 ` [PATCH 5/6] ARM: use arm setup stack function on archosg9 Vicente Bergas
2012-10-15 0:22 ` [PATCH 6/6] OMAP4: clean voltage switch Vicente Bergas
2012-10-15 7:17 ` Sascha Hauer [this message]
2012-10-15 7:27 ` [PATCH 0/6] archosg9: improve support for tablet Sascha Hauer
2012-10-18 22:22 ` vj
[not found] <[PATCH 6/6] OMAP4: clean voltage switch>
2012-10-15 21:42 ` [PATCH 6/6] OMAP4: clean voltage switch Vicente Bergas
2012-10-18 12:02 ` Teresa Gamez
2012-10-18 22:30 ` Vicente Bergas
2012-10-19 10:43 ` Jan Weitzel
2012-10-20 23:49 ` vj
2012-10-22 9:00 ` Jan Weitzel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20121015071748.GK27665@pengutronix.de \
--to=s.hauer@pengutronix.de \
--cc=barebox@lists.infradead.org \
--cc=vicencb@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox