[PATCH 0/2] add spi command

[PATCH 0/2] add spi command

[Jean-Christophe PLAGNIOL-VILLARD]

HI,

	while debugging a spi issue I found we have a i2c commands but no spi
	command

	So introduce one

The following changes since commit 56371f4e8446d04d2a5608dd5890fd87a50f888e:

  iomux-imx35: add missing comma in pad definition (2012-11-01 16:32:12 +0100)

are available in the git repository at:

  git://git.jcrosoft.org/barebox.git delivery/command_spi

for you to fetch changes up to 3d6660a40aa5a51215a1909fd2fb5702f0e6558b:

  introduce spi command (2012-11-02 08:55:11 +0800)

----------------------------------------------------------------
Jean-Christophe PLAGNIOL-VILLARD (2):
      spi: introduce spi_get_master
      introduce spi command

 commands/Kconfig  |    6 ++++++
 commands/Makefile |    1 +
 commands/spi.c    |  126 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
 drivers/spi/spi.c |   12 ++++++++++++
 include/spi/spi.h |    2 ++
 5 files changed, 147 insertions(+)
 create mode 100644 commands/spi.c

Best Regards,
J.

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

[PATCH 1/2] spi: introduce spi_get_master

[Jean-Christophe PLAGNIOL-VILLARD]

so we can request a master usefull for the spi command

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
 drivers/spi/spi.c |   12 ++++++++++++
 include/spi/spi.h |    2 ++
 2 files changed, 14 insertions(+)

diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
index 44040e5..6a5bd6d 100644
--- a/drivers/spi/spi.c
+++ b/drivers/spi/spi.c
@@ -219,6 +219,18 @@ int spi_register_master(struct spi_master *master)
 }
 EXPORT_SYMBOL(spi_register_master);
 
+struct spi_master *spi_get_master(int bus)
+{
+	struct spi_master* m;
+
+	list_for_each_entry(m, &spi_master_list, list) {
+		if (m->bus_num == bus)
+			return m;
+	}
+
+	return NULL;
+}
+
 int spi_sync(struct spi_device *spi, struct spi_message *message)
 {
 	return spi->master->transfer(spi, message);
diff --git a/include/spi/spi.h b/include/spi/spi.h
index 1773ca2..d6570a4 100644
--- a/include/spi/spi.h
+++ b/include/spi/spi.h
@@ -432,6 +432,8 @@ static inline ssize_t spi_w8r8(struct spi_device *spi, u8 cmd)
 
 extern struct bus_type spi_bus;
 
+struct spi_master *spi_get_master(int bus);
+
 static inline int spi_register_driver(struct driver_d *drv)
 {
 	drv->bus = &spi_bus;
-- 
1.7.10.4


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

[PATCH 2/2] introduce spi command

[Jean-Christophe PLAGNIOL-VILLARD]

usefull to debug spi

The command allow to read/write on a spi device

Usage: spi [OPTION] [data to write 0xXX]
write/read spi device.
  -b <bus_num>  spi bus number (default = 0)
  -r <count>    to read
  -c <cs>       chip select (default = 0)
  -m <mode>     spi mode (default = 0)
  -f <hz>       max_speed_hz (default = 1MHz)
  -w <bit>      bits_per_word (default = 8)
  -v            verbose

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
 commands/Kconfig  |    6 +++
 commands/Makefile |    1 +
 commands/spi.c    |  126 +++++++++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 133 insertions(+)
 create mode 100644 commands/spi.c

diff --git a/commands/Kconfig b/commands/Kconfig
index 16706d3..f7cbd67 100644
--- a/commands/Kconfig
+++ b/commands/Kconfig
@@ -597,6 +597,12 @@ config CMD_I2C
 	  include i2c_probe, i2c_read and i2c_write commands to communicate
 	  on i2c bus.
 
+config CMD_SPI
+	bool
+	depends on SPI
+	prompt "spi command"
+	help
+
 config CMD_LED
 	bool
 	depends on LED
diff --git a/commands/Makefile b/commands/Makefile
index 610be55..19d496e 100644
--- a/commands/Makefile
+++ b/commands/Makefile
@@ -55,6 +55,7 @@ obj-$(CONFIG_USB_GADGET_SERIAL)	+= usbserial.o
 obj-$(CONFIG_CMD_GPIO)		+= gpio.o
 obj-$(CONFIG_CMD_UNCOMPRESS)	+= uncompress.o
 obj-$(CONFIG_CMD_I2C)		+= i2c.o
+obj-$(CONFIG_CMD_SPI)		+= spi.o
 obj-$(CONFIG_CMD_UBI)		+= ubi.o
 obj-$(CONFIG_CMD_MENU)		+= menu.o
 obj-$(CONFIG_CMD_PASSWD)	+= passwd.o
diff --git a/commands/spi.c b/commands/spi.c
new file mode 100644
index 0000000..599637c
--- /dev/null
+++ b/commands/spi.c
@@ -0,0 +1,126 @@
+/*
+ * Copyright (c) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Under GPLv2 only
+ *
+ */
+
+#include <common.h>
+#include <command.h>
+#include <errno.h>
+#include <malloc.h>
+#include <getopt.h>
+#include <spi/spi.h>
+
+static int do_spi(int argc, char *argv[])
+{
+	struct spi_device spi;
+	int bus = 0;
+	int read = 0;
+	int verbose = 0;
+	int opt, count, i, ret;
+
+	u8 *tx_buf, *rx_buf;
+
+	memset(&spi, 0, sizeof(struct spi_device));
+
+	spi.max_speed_hz = 1 * 1000 * 1000;
+	spi.bits_per_word = 8;
+
+	while ((opt = getopt(argc, argv, "b:c:r:m:f:w:v")) > 0) {
+		switch (opt) {
+		case 'b':
+			bus = simple_strtol(optarg, NULL, 0);
+			break;
+		case 'r':
+			read = simple_strtol(optarg, NULL, 0);
+			break;
+		case 'c':
+			spi.chip_select = simple_strtoul(optarg, NULL, 0);
+			break;
+		case 'm':
+			spi.mode = simple_strtoul(optarg, NULL, 0);
+			break;
+		case 'f':
+			spi.max_speed_hz = simple_strtoul(optarg, NULL, 0);
+			break;
+		case 'w':
+			spi.bits_per_word = simple_strtoul(optarg, NULL, 0);
+			break;
+		case 'v':
+			verbose = 1;
+			break;
+		}
+	}
+
+	count = argc - optind;
+
+	if ((!read && !count) || !spi.max_speed_hz || !spi.bits_per_word)
+		return COMMAND_ERROR_USAGE;
+
+
+	spi.master = spi_get_master(bus);
+	if (!spi.master) {
+		printf("spi bus %d not found\n", bus);
+		return -ENODEV;
+	}
+
+	if (spi.chip_select > spi.master->num_chipselect) {
+		printf("spi chip select (%d)> master num chipselect (%d)\n",
+			spi.chip_select, spi.master->num_chipselect);
+		return -EINVAL;
+	}
+
+	tx_buf = xmalloc(count);
+	rx_buf = xmalloc(count);
+
+	for (i = 0; i < count; i++)
+		tx_buf[i] = (char) simple_strtol(argv[optind+i], NULL, 16);
+
+	ret = spi_write_then_read(&spi, tx_buf, count, rx_buf, read);
+	if (ret)
+		goto out;
+
+	if (verbose) {
+		printf("device config\n");
+		printf("    bus_num       = %d\n", spi.master->bus_num);
+		printf("    max_speed_hz  = %d\n", spi.max_speed_hz);
+		printf("    chip_select   = %d\n", spi.chip_select);
+		printf("    mode          = 0x%x\n", spi.mode);
+		printf("    bits_per_word = %d\n", spi.bits_per_word);
+		printf("\n");
+
+		printf("wrote %i bytes\n", count);
+		for (i = 0; i < count; i++)
+			printf("0x%02x ", tx_buf[i]);
+		printf("\n");
+
+		printf("read %i bytes\n", read);
+	}
+
+	for (i = 0; i < read; i++)
+		printf("0x%02x ", rx_buf[i]);
+	printf("\n");
+
+out:
+	free(rx_buf);
+	free(tx_buf);
+	return ret;
+}
+
+static const __maybe_unused char cmd_spi_help[] =
+"Usage: spi [OPTION] [data to write 0xXX]\n"
+"write/read spi device.\n"
+"  -b <bus_num>  spi bus number (default = 0)\n"
+"  -r <count>    to read\n"
+"  -c <cs>       chip select (default = 0)\n"
+"  -m <mode>     spi mode (default = 0)\n"
+"  -f <hz>       max_speed_hz (default = 1MHz)\n"
+"  -w <bit>      bits_per_word (default = 8)\n"
+"  -v            verbose\n";
+
+BAREBOX_CMD_START(spi)
+	.cmd		= do_spi,
+	.usage		= "write/read spi device",
+	BAREBOX_CMD_HELP(cmd_spi_help)
+BAREBOX_CMD_END
-- 
1.7.10.4


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

Re: [PATCH 2/2] introduce spi command

[Alexander Shiyan]

Fri,  2 Nov 2012 17:17:40 +0100 от Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> usefull to debug spi
> 
> The command allow to read/write on a spi device
> 
> Usage: spi [OPTION] [data to write 0xXX]
> write/read spi device.
>   -b <bus_num>  spi bus number (default = 0)
>   -r <count>    to read
>   -c <cs>       chip select (default = 0)
>   -m <mode>     spi mode (default = 0)
>   -f <hz>       max_speed_hz (default = 1MHz)
>   -w <bit>      bits_per_word (default = 8)
>   -v            verbose
...
> +static int do_spi(int argc, char *argv[])
> +{
> +	struct spi_device spi;
> +	int bus = 0;
> +	int read = 0;
> +	int verbose = 0;
> +	int opt, count, i, ret;
> +
> +	u8 *tx_buf, *rx_buf;
> +
> +	memset(&spi, 0, sizeof(struct spi_device));
> +
> +	spi.max_speed_hz = 1 * 1000 * 1000;
> +	spi.bits_per_word = 8;

I suggest using the default data from master for these parameters.

---
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

Re: [PATCH 2/2] introduce spi command

[Jean-Christophe PLAGNIOL-VILLARD]

On 20:26 Fri 02 Nov     , Alexander Shiyan wrote:
> Fri,  2 Nov 2012 17:17:40 +0100 от Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> > usefull to debug spi
> > 
> > The command allow to read/write on a spi device
> > 
> > Usage: spi [OPTION] [data to write 0xXX]
> > write/read spi device.
> >   -b <bus_num>  spi bus number (default = 0)
> >   -r <count>    to read
> >   -c <cs>       chip select (default = 0)
> >   -m <mode>     spi mode (default = 0)
> >   -f <hz>       max_speed_hz (default = 1MHz)
> >   -w <bit>      bits_per_word (default = 8)
> >   -v            verbose
> ...
> > +static int do_spi(int argc, char *argv[])
> > +{
> > +	struct spi_device spi;
> > +	int bus = 0;
> > +	int read = 0;
> > +	int verbose = 0;
> > +	int opt, count, i, ret;
> > +
> > +	u8 *tx_buf, *rx_buf;
> > +
> > +	memset(&spi, 0, sizeof(struct spi_device));
> > +
> > +	spi.max_speed_hz = 1 * 1000 * 1000;
> > +	spi.bits_per_word = 8;
> 
> I suggest using the default data from master for these parameters.
no otherwise we can not write the help and bits_et_word it's default value at
spi framework level is 8

and thh max_speed_hz is slow already

and it has always been the device to control it no the master

Best Regards,
J.

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

Re: [PATCH 2/2] introduce spi command

[Sascha Hauer]

On Fri, Nov 02, 2012 at 05:17:40PM +0100, Jean-Christophe PLAGNIOL-VILLARD wrote:
> usefull to debug spi
> 
> The command allow to read/write on a spi device
> 
> Usage: spi [OPTION] [data to write 0xXX]
> write/read spi device.
>   -b <bus_num>  spi bus number (default = 0)
>   -r <count>    to read
>   -c <cs>       chip select (default = 0)
>   -m <mode>     spi mode (default = 0)
>   -f <hz>       max_speed_hz (default = 1MHz)
>   -w <bit>      bits_per_word (default = 8)
>   -v            verbose
> 
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> ---
>  commands/Kconfig  |    6 +++
>  commands/Makefile |    1 +
>  commands/spi.c    |  126 +++++++++++++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 133 insertions(+)
>  create mode 100644 commands/spi.c
> 
> diff --git a/commands/Kconfig b/commands/Kconfig
> index 16706d3..f7cbd67 100644
> --- a/commands/Kconfig
> +++ b/commands/Kconfig
> @@ -597,6 +597,12 @@ config CMD_I2C
>  	  include i2c_probe, i2c_read and i2c_write commands to communicate
>  	  on i2c bus.
>  
> +config CMD_SPI
> +	bool
> +	depends on SPI
> +	prompt "spi command"
> +	help
> +
>  config CMD_LED
>  	bool
>  	depends on LED
> diff --git a/commands/Makefile b/commands/Makefile
> index 610be55..19d496e 100644
> --- a/commands/Makefile
> +++ b/commands/Makefile
> @@ -55,6 +55,7 @@ obj-$(CONFIG_USB_GADGET_SERIAL)	+= usbserial.o
>  obj-$(CONFIG_CMD_GPIO)		+= gpio.o
>  obj-$(CONFIG_CMD_UNCOMPRESS)	+= uncompress.o
>  obj-$(CONFIG_CMD_I2C)		+= i2c.o
> +obj-$(CONFIG_CMD_SPI)		+= spi.o
>  obj-$(CONFIG_CMD_UBI)		+= ubi.o
>  obj-$(CONFIG_CMD_MENU)		+= menu.o
>  obj-$(CONFIG_CMD_PASSWD)	+= passwd.o
> diff --git a/commands/spi.c b/commands/spi.c
> new file mode 100644
> index 0000000..599637c
> --- /dev/null
> +++ b/commands/spi.c
> @@ -0,0 +1,126 @@
> +/*
> + * Copyright (c) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> + *
> + * Under GPLv2 only
> + *
> + */
> +
> +#include <common.h>
> +#include <command.h>
> +#include <errno.h>
> +#include <malloc.h>
> +#include <getopt.h>
> +#include <spi/spi.h>
> +
> +static int do_spi(int argc, char *argv[])
> +{
> +	struct spi_device spi;
> +	int bus = 0;
> +	int read = 0;
> +	int verbose = 0;
> +	int opt, count, i, ret;
> +
> +	u8 *tx_buf, *rx_buf;
> +
> +	memset(&spi, 0, sizeof(struct spi_device));
> +
> +	spi.max_speed_hz = 1 * 1000 * 1000;
> +	spi.bits_per_word = 8;
> +
> +	while ((opt = getopt(argc, argv, "b:c:r:m:f:w:v")) > 0) {
> +		switch (opt) {
> +		case 'b':
> +			bus = simple_strtol(optarg, NULL, 0);
> +			break;
> +		case 'r':
> +			read = simple_strtol(optarg, NULL, 0);
> +			break;
> +		case 'c':
> +			spi.chip_select = simple_strtoul(optarg, NULL, 0);
> +			break;
> +		case 'm':
> +			spi.mode = simple_strtoul(optarg, NULL, 0);
> +			break;
> +		case 'f':
> +			spi.max_speed_hz = simple_strtoul(optarg, NULL, 0);
> +			break;
> +		case 'w':
> +			spi.bits_per_word = simple_strtoul(optarg, NULL, 0);
> +			break;
> +		case 'v':
> +			verbose = 1;
> +			break;

		default:
			return COMMAND_ERROR_USAGE;

I still didn't find the time to fix the other commands, but for new ones
we should get used to it.

Sascha

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

Re: [PATCH 0/2] add spi command

[Sascha Hauer]

On Fri, Nov 02, 2012 at 05:06:59PM +0100, Jean-Christophe PLAGNIOL-VILLARD wrote:
> HI,
> 
> 	while debugging a spi issue I found we have a i2c commands but no spi
> 	command
> 
> 	So introduce one
> 
> The following changes since commit 56371f4e8446d04d2a5608dd5890fd87a50f888e:
> 
>   iomux-imx35: add missing comma in pad definition (2012-11-01 16:32:12 +0100)
> 
> are available in the git repository at:
> 
>   git://git.jcrosoft.org/barebox.git delivery/command_spi
> 
> for you to fetch changes up to 3d6660a40aa5a51215a1909fd2fb5702f0e6558b:
> 

I recently used the i2c_* commands and thought it would be a good idea
to introduce regmap for barebox. This way we could add a regmap command
which just maps arbitrary i2c/spi devices as a cdev. Also we could
replace several drivers in drivers/mfd/ with nearly one-liners.

Sascha


-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

Re: [PATCH 0/2] add spi command

[Jean-Christophe PLAGNIOL-VILLARD]

On 20:01 Fri 02 Nov     , Sascha Hauer wrote:
> On Fri, Nov 02, 2012 at 05:06:59PM +0100, Jean-Christophe PLAGNIOL-VILLARD wrote:
> > HI,
> > 
> > 	while debugging a spi issue I found we have a i2c commands but no spi
> > 	command
> > 
> > 	So introduce one
> > 
> > The following changes since commit 56371f4e8446d04d2a5608dd5890fd87a50f888e:
> > 
> >   iomux-imx35: add missing comma in pad definition (2012-11-01 16:32:12 +0100)
> > 
> > are available in the git repository at:
> > 
> >   git://git.jcrosoft.org/barebox.git delivery/command_spi
> > 
> > for you to fetch changes up to 3d6660a40aa5a51215a1909fd2fb5702f0e6558b:
> > 
> 
> I recently used the i2c_* commands and thought it would be a good idea
> to introduce regmap for barebox. This way we could add a regmap command
> which just maps arbitrary i2c/spi devices as a cdev. Also we could
> replace several drivers in drivers/mfd/ with nearly one-liners.

why not but how to pass all the parameter to this cdev

on SPI we need some on i2c it's more simple

If this will be for the next release ok otherwise can we have this command
until then

Best Regards,
J.

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

[PATCH 0/2 v2] add spi command

[Jean-Christophe PLAGNIOL-VILLARD]

HI,

	v2:
	add default return usage
	use memory_display

	while debugging a spi issue I found we have a i2c commands but no spi
	command

	So introduce one

The following changes since commit 8f839b51047593bdd63d485006237111cd3a0547:

  spi: introduce spi_get_master (2012-11-02 08:55:10 +0800)

are available in the git repository at:

  git://git.jcrosoft.org/barebox.git delivery/command_spi

for you to fetch changes up to 2bfe0a6d58edae296b384b14e86e9efad148bfb7:

  introduce spi command (2012-11-04 01:45:34 +0800)

----------------------------------------------------------------
Jean-Christophe PLAGNIOL-VILLARD (1):
      introduce spi command

 commands/Kconfig  |    6 ++++++
 commands/Makefile |    1 +
 commands/spi.c    |  126 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 133 insertions(+)
 create mode 100644 commands/spi.c

Best Regards,
J.

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

[PATCH 1/2] spi: introduce spi_get_master

[Jean-Christophe PLAGNIOL-VILLARD]

so we can request a master usefull for the spi command

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
 drivers/spi/spi.c |   12 ++++++++++++
 include/spi/spi.h |    2 ++
 2 files changed, 14 insertions(+)

diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
index 44040e5..6a5bd6d 100644
--- a/drivers/spi/spi.c
+++ b/drivers/spi/spi.c
@@ -219,6 +219,18 @@ int spi_register_master(struct spi_master *master)
 }
 EXPORT_SYMBOL(spi_register_master);
 
+struct spi_master *spi_get_master(int bus)
+{
+	struct spi_master* m;
+
+	list_for_each_entry(m, &spi_master_list, list) {
+		if (m->bus_num == bus)
+			return m;
+	}
+
+	return NULL;
+}
+
 int spi_sync(struct spi_device *spi, struct spi_message *message)
 {
 	return spi->master->transfer(spi, message);
diff --git a/include/spi/spi.h b/include/spi/spi.h
index 1773ca2..d6570a4 100644
--- a/include/spi/spi.h
+++ b/include/spi/spi.h
@@ -432,6 +432,8 @@ static inline ssize_t spi_w8r8(struct spi_device *spi, u8 cmd)
 
 extern struct bus_type spi_bus;
 
+struct spi_master *spi_get_master(int bus);
+
 static inline int spi_register_driver(struct driver_d *drv)
 {
 	drv->bus = &spi_bus;
-- 
1.7.10.4


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

[PATCH 2/2] introduce spi command

[Jean-Christophe PLAGNIOL-VILLARD]

usefull to debug spi

The command allow to read/write on a spi device

Usage: spi [OPTION] [data to write 0xXX]
write/read spi device.
  -b <bus_num>  spi bus number (default = 0)
  -r <count>    to read
  -c <cs>       chip select (default = 0)
  -m <mode>     spi mode (default = 0)
  -f <hz>       max_speed_hz (default = 1MHz)
  -w <bit>      bits_per_word (default = 8)
  -v            verbose

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
 commands/Kconfig  |    6 +++
 commands/Makefile |    1 +
 commands/spi.c    |  126 +++++++++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 133 insertions(+)
 create mode 100644 commands/spi.c

diff --git a/commands/Kconfig b/commands/Kconfig
index 16706d3..f7cbd67 100644
--- a/commands/Kconfig
+++ b/commands/Kconfig
@@ -597,6 +597,12 @@ config CMD_I2C
 	  include i2c_probe, i2c_read and i2c_write commands to communicate
 	  on i2c bus.
 
+config CMD_SPI
+	bool
+	depends on SPI
+	prompt "spi command"
+	help
+
 config CMD_LED
 	bool
 	depends on LED
diff --git a/commands/Makefile b/commands/Makefile
index 610be55..19d496e 100644
--- a/commands/Makefile
+++ b/commands/Makefile
@@ -55,6 +55,7 @@ obj-$(CONFIG_USB_GADGET_SERIAL)	+= usbserial.o
 obj-$(CONFIG_CMD_GPIO)		+= gpio.o
 obj-$(CONFIG_CMD_UNCOMPRESS)	+= uncompress.o
 obj-$(CONFIG_CMD_I2C)		+= i2c.o
+obj-$(CONFIG_CMD_SPI)		+= spi.o
 obj-$(CONFIG_CMD_UBI)		+= ubi.o
 obj-$(CONFIG_CMD_MENU)		+= menu.o
 obj-$(CONFIG_CMD_PASSWD)	+= passwd.o
diff --git a/commands/spi.c b/commands/spi.c
new file mode 100644
index 0000000..b4663f2
--- /dev/null
+++ b/commands/spi.c
@@ -0,0 +1,126 @@
+/*
+ * Copyright (c) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Under GPLv2 only
+ *
+ */
+
+#include <common.h>
+#include <command.h>
+#include <errno.h>
+#include <malloc.h>
+#include <getopt.h>
+#include <spi/spi.h>
+
+static int do_spi(int argc, char *argv[])
+{
+	struct spi_device spi;
+	int bus = 0;
+	int read = 0;
+	int verbose = 0;
+	int opt, count, i, ret;
+	int byte_per_word;
+
+	u8 *tx_buf, *rx_buf;
+
+	memset(&spi, 0, sizeof(struct spi_device));
+
+	spi.max_speed_hz = 1 * 1000 * 1000;
+	spi.bits_per_word = 8;
+
+	while ((opt = getopt(argc, argv, "b:c:r:m:f:w:v")) > 0) {
+		switch (opt) {
+		case 'b':
+			bus = simple_strtol(optarg, NULL, 0);
+			break;
+		case 'r':
+			read = simple_strtol(optarg, NULL, 0);
+			break;
+		case 'c':
+			spi.chip_select = simple_strtoul(optarg, NULL, 0);
+			break;
+		case 'm':
+			spi.mode = simple_strtoul(optarg, NULL, 0);
+			break;
+		case 'f':
+			spi.max_speed_hz = simple_strtoul(optarg, NULL, 0);
+			break;
+		case 'w':
+			spi.bits_per_word = simple_strtoul(optarg, NULL, 0);
+			break;
+		case 'v':
+			verbose = 1;
+			break;
+		default:
+			return COMMAND_ERROR_USAGE;
+		}
+	}
+
+	count = argc - optind;
+
+	if ((!read && !count) || !spi.max_speed_hz || !spi.bits_per_word)
+		return COMMAND_ERROR_USAGE;
+
+
+	spi.master = spi_get_master(bus);
+	if (!spi.master) {
+		printf("spi bus %d not found\n", bus);
+		return -ENODEV;
+	}
+
+	if (spi.chip_select > spi.master->num_chipselect) {
+		printf("spi chip select (%d)> master num chipselect (%d)\n",
+			spi.chip_select, spi.master->num_chipselect);
+		return -EINVAL;
+	}
+
+	tx_buf = xmalloc(count);
+	rx_buf = xmalloc(count);
+
+	for (i = 0; i < count; i++)
+		tx_buf[i] = (u8) simple_strtol(argv[optind + i], NULL, 16);
+
+	ret = spi_write_then_read(&spi, tx_buf, count, rx_buf, read);
+	if (ret)
+		goto out;
+
+	byte_per_word = min(spi.bits_per_word / 8, 1);
+	if (verbose) {
+		printf("device config\n");
+		printf("    bus_num       = %d\n", spi.master->bus_num);
+		printf("    max_speed_hz  = %d\n", spi.max_speed_hz);
+		printf("    chip_select   = %d\n", spi.chip_select);
+		printf("    mode          = 0x%x\n", spi.mode);
+		printf("    bits_per_word = %d\n", spi.bits_per_word);
+		printf("\n");
+
+		printf("wrote %i bytes\n", count);
+		memory_display(tx_buf, 0, count, byte_per_word);
+
+		printf("read %i bytes\n", read);
+	}
+
+	memory_display(rx_buf, 0, read, byte_per_word);
+
+out:
+	free(rx_buf);
+	free(tx_buf);
+	return ret;
+}
+
+static const __maybe_unused char cmd_spi_help[] =
+"Usage: spi [OPTION] [data to write 0xXX]\n"
+"write/read spi device.\n"
+"  -b <bus_num>  spi bus number (default = 0)\n"
+"  -r <count>    to read\n"
+"  -c <cs>       chip select (default = 0)\n"
+"  -m <mode>     spi mode (default = 0)\n"
+"  -f <hz>       max_speed_hz (default = 1MHz)\n"
+"  -w <bit>      bits_per_word (default = 8)\n"
+"  -v            verbose\n";
+
+BAREBOX_CMD_START(spi)
+	.cmd		= do_spi,
+	.usage		= "write/read spi device",
+	BAREBOX_CMD_HELP(cmd_spi_help)
+BAREBOX_CMD_END
-- 
1.7.10.4


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

[PATCH 0/2 v3] add spi command

[Jean-Christophe PLAGNIOL-VILLARD]

HI,

	v3:
	call setup before accesing the device
	This was working properly on at91 as the driver is wrong.
	It call setup for every transfer. I will fix the atmel_spi.

	v2:
	add default return usage
	use memory_display

	while debugging a spi issue I found we have a i2c commands but no spi
	command

	So introduce one

The following changes since commit 56371f4e8446d04d2a5608dd5890fd87a50f888e:

  iomux-imx35: add missing comma in pad definition (2012-11-01 16:32:12 +0100)

are available in the git repository at:

  git://git.jcrosoft.org/barebox.git delivery/command_spi

for you to fetch changes up to da7ef46034f3f0344a8fbbd3ce2bde70c9ec4685:

  introduce spi command (2012-11-05 02:18:14 +0800)

----------------------------------------------------------------
Jean-Christophe PLAGNIOL-VILLARD (2):
      spi: introduce spi_get_master
      introduce spi command

 commands/Kconfig        |    6 ++++++
 commands/Makefile       |    1 +
 commands/spi.c          |  132 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
 drivers/spi/atmel_spi.c |    1 +
 drivers/spi/spi.c       |   12 ++++++++++++
 include/spi/spi.h       |    2 ++
 6 files changed, 154 insertions(+)
 create mode 100644 commands/spi.c

Best Regards,
J.

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

[PATCH 1/2] spi: introduce spi_get_master

[Jean-Christophe PLAGNIOL-VILLARD]

so we can request a master usefull for the spi command

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
 drivers/spi/spi.c |   12 ++++++++++++
 include/spi/spi.h |    2 ++
 2 files changed, 14 insertions(+)

diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
index 44040e5..6a5bd6d 100644
--- a/drivers/spi/spi.c
+++ b/drivers/spi/spi.c
@@ -219,6 +219,18 @@ int spi_register_master(struct spi_master *master)
 }
 EXPORT_SYMBOL(spi_register_master);
 
+struct spi_master *spi_get_master(int bus)
+{
+	struct spi_master* m;
+
+	list_for_each_entry(m, &spi_master_list, list) {
+		if (m->bus_num == bus)
+			return m;
+	}
+
+	return NULL;
+}
+
 int spi_sync(struct spi_device *spi, struct spi_message *message)
 {
 	return spi->master->transfer(spi, message);
diff --git a/include/spi/spi.h b/include/spi/spi.h
index 1773ca2..d6570a4 100644
--- a/include/spi/spi.h
+++ b/include/spi/spi.h
@@ -432,6 +432,8 @@ static inline ssize_t spi_w8r8(struct spi_device *spi, u8 cmd)
 
 extern struct bus_type spi_bus;
 
+struct spi_master *spi_get_master(int bus);
+
 static inline int spi_register_driver(struct driver_d *drv)
 {
 	drv->bus = &spi_bus;
-- 
1.7.10.4


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

[PATCH 2/2] introduce spi command

[Jean-Christophe PLAGNIOL-VILLARD]

usefull to debug spi

The command allow to read/write on a spi device

Usage: spi [OPTION] [data to write 0xXX]
write/read spi device.
  -b <bus_num>  spi bus number (default = 0)
  -r <count>    to read
  -c <cs>       chip select (default = 0)
  -m <mode>     spi mode (default = 0)
  -f <hz>       max_speed_hz (default = 1MHz)
  -w <bit>      bits_per_word (default = 8)
  -v            verbose

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
 commands/Kconfig        |    6 +++
 commands/Makefile       |    1 +
 commands/spi.c          |  132 +++++++++++++++++++++++++++++++++++++++++++++++
 drivers/spi/atmel_spi.c |    1 +
 4 files changed, 140 insertions(+)
 create mode 100644 commands/spi.c

diff --git a/commands/Kconfig b/commands/Kconfig
index 16706d3..f7cbd67 100644
--- a/commands/Kconfig
+++ b/commands/Kconfig
@@ -597,6 +597,12 @@ config CMD_I2C
 	  include i2c_probe, i2c_read and i2c_write commands to communicate
 	  on i2c bus.
 
+config CMD_SPI
+	bool
+	depends on SPI
+	prompt "spi command"
+	help
+
 config CMD_LED
 	bool
 	depends on LED
diff --git a/commands/Makefile b/commands/Makefile
index 610be55..19d496e 100644
--- a/commands/Makefile
+++ b/commands/Makefile
@@ -55,6 +55,7 @@ obj-$(CONFIG_USB_GADGET_SERIAL)	+= usbserial.o
 obj-$(CONFIG_CMD_GPIO)		+= gpio.o
 obj-$(CONFIG_CMD_UNCOMPRESS)	+= uncompress.o
 obj-$(CONFIG_CMD_I2C)		+= i2c.o
+obj-$(CONFIG_CMD_SPI)		+= spi.o
 obj-$(CONFIG_CMD_UBI)		+= ubi.o
 obj-$(CONFIG_CMD_MENU)		+= menu.o
 obj-$(CONFIG_CMD_PASSWD)	+= passwd.o
diff --git a/commands/spi.c b/commands/spi.c
new file mode 100644
index 0000000..32a047d
--- /dev/null
+++ b/commands/spi.c
@@ -0,0 +1,132 @@
+/*
+ * Copyright (c) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Under GPLv2 only
+ *
+ */
+
+#include <common.h>
+#include <command.h>
+#include <errno.h>
+#include <malloc.h>
+#include <getopt.h>
+#include <spi/spi.h>
+
+static int do_spi(int argc, char *argv[])
+{
+	struct spi_device spi;
+	int bus = 0;
+	int read = 0;
+	int verbose = 0;
+	int opt, count, i, ret;
+	int byte_per_word;
+
+	u8 *tx_buf, *rx_buf;
+
+	memset(&spi, 0, sizeof(struct spi_device));
+
+	spi.max_speed_hz = 1 * 1000 * 1000;
+	spi.bits_per_word = 8;
+
+	while ((opt = getopt(argc, argv, "b:c:r:m:f:w:v")) > 0) {
+		switch (opt) {
+		case 'b':
+			bus = simple_strtol(optarg, NULL, 0);
+			break;
+		case 'r':
+			read = simple_strtol(optarg, NULL, 0);
+			break;
+		case 'c':
+			spi.chip_select = simple_strtoul(optarg, NULL, 0);
+			break;
+		case 'm':
+			spi.mode = simple_strtoul(optarg, NULL, 0);
+			break;
+		case 'f':
+			spi.max_speed_hz = simple_strtoul(optarg, NULL, 0);
+			break;
+		case 'w':
+			spi.bits_per_word = simple_strtoul(optarg, NULL, 0);
+			break;
+		case 'v':
+			verbose = 1;
+			break;
+		default:
+			return COMMAND_ERROR_USAGE;
+		}
+	}
+
+	count = argc - optind;
+
+	if ((!read && !count) || !spi.max_speed_hz || !spi.bits_per_word)
+		return COMMAND_ERROR_USAGE;
+
+
+	spi.master = spi_get_master(bus);
+	if (!spi.master) {
+		printf("spi bus %d not found\n", bus);
+		return -ENODEV;
+	}
+
+	if (spi.chip_select > spi.master->num_chipselect) {
+		printf("spi chip select (%d)> master num chipselect (%d)\n",
+			spi.chip_select, spi.master->num_chipselect);
+		return -EINVAL;
+	}
+
+	ret = spi.master->setup(&spi);
+	if (ret) {
+		printf("can not setup the master (%d)\n", ret);
+		return -ret;
+	}
+
+	tx_buf = xmalloc(count);
+	rx_buf = xmalloc(count);
+
+	for (i = 0; i < count; i++)
+		tx_buf[i] = (u8) simple_strtol(argv[optind + i], NULL, 16);
+
+	ret = spi_write_then_read(&spi, tx_buf, count, rx_buf, read);
+	if (ret)
+		goto out;
+
+	byte_per_word = max(spi.bits_per_word / 8, 1);
+	if (verbose) {
+		printf("device config\n");
+		printf("    bus_num       = %d\n", spi.master->bus_num);
+		printf("    max_speed_hz  = %d\n", spi.max_speed_hz);
+		printf("    chip_select   = %d\n", spi.chip_select);
+		printf("    mode          = 0x%x\n", spi.mode);
+		printf("    bits_per_word = %d\n", spi.bits_per_word);
+		printf("\n");
+
+		printf("wrote %i bytes\n", count);
+		memory_display(tx_buf, 0, count, byte_per_word);
+
+		printf("read %i bytes\n", read);
+	}
+
+	memory_display(rx_buf, 0, read, byte_per_word);
+
+out:
+	free(rx_buf);
+	free(tx_buf);
+	return ret;
+}
+
+static const __maybe_unused char cmd_spi_help[] =
+"Usage: spi [OPTION] [data to write 0xXX]\n"
+"write/read spi device.\n"
+"  -b <bus_num>  spi bus number (default = 0)\n"
+"  -r <count>    to read\n"
+"  -c <cs>       chip select (default = 0)\n"
+"  -m <mode>     spi mode (default = 0)\n"
+"  -f <hz>       max_speed_hz (default = 1MHz)\n"
+"  -w <bit>      bits_per_word (default = 8)\n"
+"  -v            verbose\n";
+
+BAREBOX_CMD_START(spi)
+	.cmd		= do_spi,
+	.usage		= "write/read spi device",
+	BAREBOX_CMD_HELP(cmd_spi_help)
+BAREBOX_CMD_END
diff --git a/drivers/spi/atmel_spi.c b/drivers/spi/atmel_spi.c
index 43aec8e..4a6ed96 100644
--- a/drivers/spi/atmel_spi.c
+++ b/drivers/spi/atmel_spi.c
@@ -21,6 +21,7 @@
  *
  *
  */
+#define DEBUG
 
 #include <common.h>
 #include <init.h>
-- 
1.7.10.4


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

[PATCH 0/2 v4] add spi command

[Jean-Christophe PLAGNIOL-VILLARD]

HI,

	v4:
	do not touch the atmel_spi

	v3:
	call setup before accesing the device
	This was working properly on at91 as the driver is wrong.
	It call setup for every transfer. I will fix the atmel_spi.

	v2:
	add default return usage
	use memory_display

	while debugging a spi issue I found we have a i2c commands but no spi
	command

	So introduce one

The following changes since commit 56371f4e8446d04d2a5608dd5890fd87a50f888e:

  iomux-imx35: add missing comma in pad definition (2012-11-01 16:32:12 +0100)

are available in the git repository at:

  git://git.jcrosoft.org/barebox.git delivery/command_spi

for you to fetch changes up to 268e3d4f67da35571159fd096c62fa2e660783b0:

  introduce spi command (2012-11-05 11:13:25 +0800)

----------------------------------------------------------------
Jean-Christophe PLAGNIOL-VILLARD (2):
      spi: introduce spi_get_master
      introduce spi command

 commands/Kconfig  |    6 ++++++
 commands/Makefile |    1 +
 commands/spi.c    |  132 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
 drivers/spi/spi.c |   12 ++++++++++++
 include/spi/spi.h |    2 ++
 5 files changed, 153 insertions(+)
 create mode 100644 commands/spi.c

Best Regards,
J.

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

[PATCH 1/2] spi: introduce spi_get_master

[Jean-Christophe PLAGNIOL-VILLARD]

so we can request a master usefull for the spi command

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
 drivers/spi/spi.c |   12 ++++++++++++
 include/spi/spi.h |    2 ++
 2 files changed, 14 insertions(+)

diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
index 44040e5..6a5bd6d 100644
--- a/drivers/spi/spi.c
+++ b/drivers/spi/spi.c
@@ -219,6 +219,18 @@ int spi_register_master(struct spi_master *master)
 }
 EXPORT_SYMBOL(spi_register_master);
 
+struct spi_master *spi_get_master(int bus)
+{
+	struct spi_master* m;
+
+	list_for_each_entry(m, &spi_master_list, list) {
+		if (m->bus_num == bus)
+			return m;
+	}
+
+	return NULL;
+}
+
 int spi_sync(struct spi_device *spi, struct spi_message *message)
 {
 	return spi->master->transfer(spi, message);
diff --git a/include/spi/spi.h b/include/spi/spi.h
index 1773ca2..d6570a4 100644
--- a/include/spi/spi.h
+++ b/include/spi/spi.h
@@ -432,6 +432,8 @@ static inline ssize_t spi_w8r8(struct spi_device *spi, u8 cmd)
 
 extern struct bus_type spi_bus;
 
+struct spi_master *spi_get_master(int bus);
+
 static inline int spi_register_driver(struct driver_d *drv)
 {
 	drv->bus = &spi_bus;
-- 
1.7.10.4


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

[PATCH 2/2] introduce spi command

[Jean-Christophe PLAGNIOL-VILLARD]

usefull to debug spi

The command allow to read/write on a spi device

Usage: spi [OPTION] [data to write 0xXX]
write/read spi device.
  -b <bus_num>  spi bus number (default = 0)
  -r <count>    to read
  -c <cs>       chip select (default = 0)
  -m <mode>     spi mode (default = 0)
  -f <hz>       max_speed_hz (default = 1MHz)
  -w <bit>      bits_per_word (default = 8)
  -v            verbose

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
 commands/Kconfig  |    6 +++
 commands/Makefile |    1 +
 commands/spi.c    |  132 +++++++++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 139 insertions(+)
 create mode 100644 commands/spi.c

diff --git a/commands/Kconfig b/commands/Kconfig
index 16706d3..f7cbd67 100644
--- a/commands/Kconfig
+++ b/commands/Kconfig
@@ -597,6 +597,12 @@ config CMD_I2C
 	  include i2c_probe, i2c_read and i2c_write commands to communicate
 	  on i2c bus.
 
+config CMD_SPI
+	bool
+	depends on SPI
+	prompt "spi command"
+	help
+
 config CMD_LED
 	bool
 	depends on LED
diff --git a/commands/Makefile b/commands/Makefile
index 610be55..19d496e 100644
--- a/commands/Makefile
+++ b/commands/Makefile
@@ -55,6 +55,7 @@ obj-$(CONFIG_USB_GADGET_SERIAL)	+= usbserial.o
 obj-$(CONFIG_CMD_GPIO)		+= gpio.o
 obj-$(CONFIG_CMD_UNCOMPRESS)	+= uncompress.o
 obj-$(CONFIG_CMD_I2C)		+= i2c.o
+obj-$(CONFIG_CMD_SPI)		+= spi.o
 obj-$(CONFIG_CMD_UBI)		+= ubi.o
 obj-$(CONFIG_CMD_MENU)		+= menu.o
 obj-$(CONFIG_CMD_PASSWD)	+= passwd.o
diff --git a/commands/spi.c b/commands/spi.c
new file mode 100644
index 0000000..899bf62
--- /dev/null
+++ b/commands/spi.c
@@ -0,0 +1,132 @@
+/*
+ * Copyright (c) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Under GPLv2 only
+ *
+ */
+
+#include <common.h>
+#include <command.h>
+#include <errno.h>
+#include <malloc.h>
+#include <getopt.h>
+#include <spi/spi.h>
+
+static int do_spi(int argc, char *argv[])
+{
+	struct spi_device spi;
+	int bus = 0;
+	int read = 0;
+	int verbose = 0;
+	int opt, count, i, ret;
+	int byte_per_word;
+
+	u8 *tx_buf, *rx_buf;
+
+	memset(&spi, 0, sizeof(struct spi_device));
+
+	spi.max_speed_hz = 1 * 1000 * 1000;
+	spi.bits_per_word = 8;
+
+	while ((opt = getopt(argc, argv, "b:c:r:m:f:w:v")) > 0) {
+		switch (opt) {
+		case 'b':
+			bus = simple_strtol(optarg, NULL, 0);
+			break;
+		case 'r':
+			read = simple_strtol(optarg, NULL, 0);
+			break;
+		case 'c':
+			spi.chip_select = simple_strtoul(optarg, NULL, 0);
+			break;
+		case 'm':
+			spi.mode = simple_strtoul(optarg, NULL, 0);
+			break;
+		case 'f':
+			spi.max_speed_hz = simple_strtoul(optarg, NULL, 0);
+			break;
+		case 'w':
+			spi.bits_per_word = simple_strtoul(optarg, NULL, 0);
+			break;
+		case 'v':
+			verbose = 1;
+			break;
+		default:
+			return COMMAND_ERROR_USAGE;
+		}
+	}
+
+	count = argc - optind;
+
+	if ((!read && !count) || !spi.max_speed_hz || !spi.bits_per_word)
+		return COMMAND_ERROR_USAGE;
+
+
+	spi.master = spi_get_master(bus);
+	if (!spi.master) {
+		printf("spi bus %d not found\n", bus);
+		return -ENODEV;
+	}
+
+	if (spi.chip_select > spi.master->num_chipselect) {
+		printf("spi chip select (%d)> master num chipselect (%d)\n",
+			spi.chip_select, spi.master->num_chipselect);
+		return -EINVAL;
+	}
+
+	ret = spi.master->setup(&spi);
+	if (ret) {
+		printf("can not setup the master (%d)\n", ret);
+		return ret;
+	}
+
+	tx_buf = xmalloc(count);
+	rx_buf = xmalloc(count);
+
+	for (i = 0; i < count; i++)
+		tx_buf[i] = (u8) simple_strtol(argv[optind + i], NULL, 16);
+
+	ret = spi_write_then_read(&spi, tx_buf, count, rx_buf, read);
+	if (ret)
+		goto out;
+
+	byte_per_word = max(spi.bits_per_word / 8, 1);
+	if (verbose) {
+		printf("device config\n");
+		printf("    bus_num       = %d\n", spi.master->bus_num);
+		printf("    max_speed_hz  = %d\n", spi.max_speed_hz);
+		printf("    chip_select   = %d\n", spi.chip_select);
+		printf("    mode          = 0x%x\n", spi.mode);
+		printf("    bits_per_word = %d\n", spi.bits_per_word);
+		printf("\n");
+
+		printf("wrote %i bytes\n", count);
+		memory_display(tx_buf, 0, count, byte_per_word);
+
+		printf("read %i bytes\n", read);
+	}
+
+	memory_display(rx_buf, 0, read, byte_per_word);
+
+out:
+	free(rx_buf);
+	free(tx_buf);
+	return ret;
+}
+
+static const __maybe_unused char cmd_spi_help[] =
+"Usage: spi [OPTION] [data to write 0xXX]\n"
+"write/read spi device.\n"
+"  -b <bus_num>  spi bus number (default = 0)\n"
+"  -r <count>    to read\n"
+"  -c <cs>       chip select (default = 0)\n"
+"  -m <mode>     spi mode (default = 0)\n"
+"  -f <hz>       max_speed_hz (default = 1MHz)\n"
+"  -w <bit>      bits_per_word (default = 8)\n"
+"  -v            verbose\n";
+
+BAREBOX_CMD_START(spi)
+	.cmd		= do_spi,
+	.usage		= "write/read spi device",
+	BAREBOX_CMD_HELP(cmd_spi_help)
+BAREBOX_CMD_END
-- 
1.7.10.4


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox