mail archive of the barebox mailing list
 help / color / mirror / Atom feed
From: Sascha Hauer <s.hauer@pengutronix.de>
To: Andreas Pretzsch <apr@cn-eng.de>
Cc: barebox@lists.infradead.org
Subject: Re: [PATCH] net smc911x: add support for external PHY
Date: Mon, 12 Nov 2012 08:30:00 +0100	[thread overview]
Message-ID: <20121112073000.GG10369@pengutronix.de> (raw)
In-Reply-To: <1352330703-27402-1-git-send-email-apr@cn-eng.de>

On Thu, Nov 08, 2012 at 12:25:03AM +0100, Andreas Pretzsch wrote:
> On LAN9115/LAN9117/LAN9215/LAN9217, external PHYs are supported.
> Switch to external PHY based on hardware strap pin and/or override flags.
> Also add a mask to platform data selecting external PHY address to be used.
> 
> Code based on linux/drivers/net/ethernet/smsc/smsc911x.c (fd9abb3d, d23f028a).

Applied, thanks

Sascha

> ---
> Code is tested on a SMSC LAN9217 with an external PHY (switch chip attached
> in PHY mode via MII), the external mode works as expected.
> As I have no board at hand using the internal PHY of the controller (or any
> of these family), I cannot verify the current behaviour, beside looking at
> the internal PHY register (which are fine).
> But as the modifications are mostly 1:1 copies of the respective Linux mainline
> code, slightly adapted for Barebox, I expect no problems here.
> 
> Patch is against current next, but should also match current master.
> CC'ing last active authors.
> 
>  drivers/net/smc911x.c |   97 +++++++++++++++++++++++++++++++++++++++++++++++--
>  include/smc911x.h     |    6 +++
>  2 files changed, 99 insertions(+), 4 deletions(-)
> 
> diff --git a/drivers/net/smc911x.c b/drivers/net/smc911x.c
> index c657fec..28c69ba 100644
> --- a/drivers/net/smc911x.c
> +++ b/drivers/net/smc911x.c
> @@ -44,6 +44,10 @@ struct smc911x_priv {
>  
>  	int shift;
>  	int generation;
> +	unsigned int flags;
> +	unsigned int idrev;
> +	unsigned int using_extphy;
> +	unsigned int phy_mask;
>  
>  	u32 (*reg_read)(struct smc911x_priv *priv, u32 reg);
>  	void (*reg_write)(struct smc911x_priv *priv, u32 reg, u32 val);
> @@ -225,6 +229,60 @@ static int smc911x_phy_write(struct mii_bus *bus, int phy_addr,
>  	return 0;
>  }
>  
> +/* Switch to external phy. Assumes tx and rx are stopped. */
> +static void smsc911x_phy_enable_external(struct eth_device *edev)
> +{
> +	struct smc911x_priv *priv = edev->priv;
> +	u32 hwcfg = smc911x_reg_read(priv, HW_CFG);
> +
> +	/* Disable phy clocks to the MAC */
> +	hwcfg &= (~HW_CFG_PHY_CLK_SEL);
> +	hwcfg |= HW_CFG_PHY_CLK_SEL_CLK_DIS;
> +	smc911x_reg_write(priv, HW_CFG, hwcfg);
> +	udelay(10);	/* Enough time for clocks to stop */
> +
> +	/* Switch to external phy */
> +	hwcfg |= HW_CFG_EXT_PHY_EN;
> +	smc911x_reg_write(priv, HW_CFG, hwcfg);
> +
> +	/* Enable phy clocks to the MAC */
> +	hwcfg &= (~HW_CFG_PHY_CLK_SEL);
> +	hwcfg |= HW_CFG_PHY_CLK_SEL_EXT_PHY;
> +	smc911x_reg_write(priv, HW_CFG, hwcfg);
> +	udelay(10);	/* Enough time for clocks to restart */
> +
> +	/* Switch MDIO/MDC to external PHY */
> +	hwcfg |= HW_CFG_SMI_SEL;
> +	smc911x_reg_write(priv, HW_CFG, hwcfg);
> +}
> +
> +/* Autodetects and enables external phy if present on supported chips.
> + * autodetection can be overridden by specifying SMC911X_FORCE_INTERNAL_PHY
> + * or SMC911X_FORCE_EXTERNAL_PHY in the platform_data flags. */
> +static void smsc911x_phy_initialise_external(struct eth_device *edev)
> +{
> +	struct smc911x_priv *priv = edev->priv;
> +	u32 hwcfg = smc911x_reg_read(priv, HW_CFG);
> +
> +	if (priv->flags & SMC911X_FORCE_INTERNAL_PHY) {
> +		dev_info(edev->parent, "Forcing internal PHY\n");
> +		priv->using_extphy = 0;
> +	} else if (priv->flags & SMC911X_FORCE_EXTERNAL_PHY) {
> +		dev_info(edev->parent, "Forcing external PHY\n");
> +		smsc911x_phy_enable_external(edev);
> +		priv->using_extphy = 1;
> +	} else if (hwcfg & HW_CFG_EXT_PHY_DET) {
> +		dev_info(edev->parent,
> +			"HW_CFG EXT_PHY_DET set, using external PHY\n");
> +		smsc911x_phy_enable_external(edev);
> +		priv->using_extphy = 1;
> +	} else {
> +		dev_info(edev->parent,
> +			"HW_CFG EXT_PHY_DET clear, using internal PHY\n");
> +		priv->using_extphy = 0;
> +	}
> +}
> +
>  static int smc911x_phy_reset(struct eth_device *edev)
>  {
>  	struct smc911x_priv *priv = edev->priv;
> @@ -284,14 +342,41 @@ static void smc911x_reset(struct eth_device *edev)
>  
>  	/* Set to LED outputs */
>  	smc911x_reg_write(priv, GPIO_CFG, 0x70070000);
> +
> +	/* Select internal/external PHY */
> +	switch (priv->idrev & 0xFFFF0000) {
> +	case 0x01170000:
> +	case 0x01150000:
> +	case 0x117A0000:
> +	case 0x115A0000:
> +		/* External PHY supported, try to autodetect */
> +		smsc911x_phy_initialise_external(edev);
> +		break;
> +	default:
> +		dev_dbg(edev->parent, "External PHY is not supported, "
> +			"using internal PHY\n");
> +		priv->using_extphy = 0;
> +		break;
> +	}
> +
> +	if (!priv->using_extphy) {
> +		/* Mask all PHYs except ID 1 (internal) */
> +		priv->miibus.phy_mask = ~(1 << 1);
> +	} else {
> +		/* Mask PHYs as requested (or try all if mask is 0) */
> +		/* Attn.: first probed PHY is used by phy_device_connect */
> +		priv->miibus.phy_mask = priv->phy_mask;
> +	}
>  }
>  
>  static void smc911x_enable(struct eth_device *edev)
>  {
>  	struct smc911x_priv *priv = edev->priv;
> +	u32 hw_cfg_phy_settings;
>  
>  	/* Enable TX */
> -	smc911x_reg_write(priv, HW_CFG, 8 << 16 | HW_CFG_SF);
> +	hw_cfg_phy_settings = smc911x_reg_read(priv, HW_CFG) & (HW_CFG_PHY_CLK_SEL|HW_CFG_SMI_SEL|HW_CFG_EXT_PHY_EN);
> +	smc911x_reg_write(priv, HW_CFG, 8 << 16 | HW_CFG_SF | hw_cfg_phy_settings);
>  
>  	smc911x_reg_write(priv, GPT_CFG, GPT_CFG_TIMER_EN | 10000);
>  
> @@ -306,7 +391,8 @@ static int smc911x_eth_open(struct eth_device *edev)
>  	struct smc911x_priv *priv = (struct smc911x_priv *)edev->priv;
>  	int ret;
>  
> -	ret = phy_device_connect(edev, &priv->miibus, 1, NULL,
> +	/* use first probed PHY (see also phy_mask) */
> +	ret = phy_device_connect(edev, &priv->miibus, -1, NULL,
>  				 0, PHY_INTERFACE_MODE_NA);
>  	if (ret)
>  		return ret;
> @@ -426,8 +512,11 @@ static int smc911x_probe(struct device_d *dev)
>  		is_32bit = is_32bit == IORESOURCE_MEM_32BIT;
>  	priv->base = dev_request_mem_region(dev, 0);
>  
> -	if (pdata && pdata->shift)
> +	if (pdata) {
>  		priv->shift = pdata->shift;
> +		priv->flags = pdata->flags;
> +		priv->phy_mask = pdata->phy_mask;
> +	}
>  
>  	if (is_32bit) {
>  		if (priv->shift) {
> @@ -483,7 +572,7 @@ static int smc911x_probe(struct device_d *dev)
>  		return -ENODEV;
>  	}
>  
> -	val = smc911x_reg_read(priv, ID_REV);
> +	priv->idrev = val = smc911x_reg_read(priv, ID_REV);
>  	switch (val & 0xFFFF0000) {
>  	case 0x01180000:
>  	case 0x01170000:
> diff --git a/include/smc911x.h b/include/smc911x.h
> index 148906b..4a802ee 100644
> --- a/include/smc911x.h
> +++ b/include/smc911x.h
> @@ -13,6 +13,12 @@
>   */
>  struct smc911x_plat {
>  	int shift;
> +	unsigned int flags;
> +	unsigned int phy_mask;	/* external PHY only: mask out PHYs,
> +				   e.g. ~(1 << 5) to use PHY addr 5 */
>  };
>  
> +#define SMC911X_FORCE_INTERNAL_PHY	0x01
> +#define SMC911X_FORCE_EXTERNAL_PHY	0x02
> +
>  #endif /* __SMC911X_PLATFORM_H_ */
> -- 
> 1.7.10.4
> 
> 

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

      reply	other threads:[~2012-11-12  7:30 UTC|newest]

Thread overview: 2+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2012-11-07 23:25 Andreas Pretzsch
2012-11-12  7:30 ` Sascha Hauer [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20121112073000.GG10369@pengutronix.de \
    --to=s.hauer@pengutronix.de \
    --cc=apr@cn-eng.de \
    --cc=barebox@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox