mail archive of the barebox mailing list
 help / color / mirror / Atom feed
* [PATCH] ARM: at91: Add Telit EVK-PRO3 board support
@ 2013-01-18 16:14 Fabio Porcedda
  2013-01-19  7:06 ` Jean-Christophe PLAGNIOL-VILLARD
  0 siblings, 1 reply; 3+ messages in thread
From: Fabio Porcedda @ 2013-01-18 16:14 UTC (permalink / raw)
  To: barebox

http://www.telit.com

Based on at91sam9260ek board support.

Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
---
 arch/arm/Makefile                               |   1 +
 arch/arm/boards/evk-pro3/Makefile               |   1 +
 arch/arm/boards/evk-pro3/config.h               |   6 +
 arch/arm/boards/evk-pro3/env/boot/nand-ubi      |  10 +
 arch/arm/boards/evk-pro3/env/init/config-board  |   8 +
 arch/arm/boards/evk-pro3/env/init/mtdparts-nand |  11 ++
 arch/arm/boards/evk-pro3/env/init/usb           |  10 +
 arch/arm/boards/evk-pro3/init.c                 | 233 ++++++++++++++++++++++++
 arch/arm/configs/evk_pro3_defconfig             |  73 ++++++++
 arch/arm/mach-at91/Kconfig                      |   9 +
 10 files changed, 362 insertions(+)
 create mode 100644 arch/arm/boards/evk-pro3/Makefile
 create mode 100644 arch/arm/boards/evk-pro3/config.h
 create mode 100644 arch/arm/boards/evk-pro3/env/boot/nand-ubi
 create mode 100644 arch/arm/boards/evk-pro3/env/init/config-board
 create mode 100644 arch/arm/boards/evk-pro3/env/init/mtdparts-nand
 create mode 100644 arch/arm/boards/evk-pro3/env/init/usb
 create mode 100644 arch/arm/boards/evk-pro3/init.c
 create mode 100644 arch/arm/configs/evk_pro3_defconfig

diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index a36adfb..e5c7761 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -94,6 +94,7 @@ board-$(CONFIG_MACH_EUKREA_CPUIMX35)		:= eukrea_cpuimx35
 board-$(CONFIG_MACH_EUKREA_CPUIMX51SD)		:= eukrea_cpuimx51
 board-$(CONFIG_MACH_FREESCALE_MX25_3STACK)	:= freescale-mx25-3-stack
 board-$(CONFIG_MACH_FREESCALE_MX35_3STACK)	:= freescale-mx35-3-stack
+board-$(CONFIG_MACH_GE863)			:= evk-pro3
 board-$(CONFIG_MACH_IMX21ADS)			:= imx21ads
 board-$(CONFIG_MACH_IMX27ADS)			:= imx27ads
 board-$(CONFIG_MACH_IMX233_OLINUXINO)	:= imx233-olinuxino
diff --git a/arch/arm/boards/evk-pro3/Makefile b/arch/arm/boards/evk-pro3/Makefile
new file mode 100644
index 0000000..eb072c0
--- /dev/null
+++ b/arch/arm/boards/evk-pro3/Makefile
@@ -0,0 +1 @@
+obj-y += init.o
diff --git a/arch/arm/boards/evk-pro3/config.h b/arch/arm/boards/evk-pro3/config.h
new file mode 100644
index 0000000..7aeff30
--- /dev/null
+++ b/arch/arm/boards/evk-pro3/config.h
@@ -0,0 +1,6 @@
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define AT91_MAIN_CLOCK		6000000		/*  6.000 MHz crystal */
+
+#endif	/* __CONFIG_H */
diff --git a/arch/arm/boards/evk-pro3/env/boot/nand-ubi b/arch/arm/boards/evk-pro3/env/boot/nand-ubi
new file mode 100644
index 0000000..8115ced
--- /dev/null
+++ b/arch/arm/boards/evk-pro3/env/boot/nand-ubi
@@ -0,0 +1,10 @@
+#!/bin/sh
+
+if [ "$1" = menu ]; then
+	boot-menu-add-entry "$0" "nand (UBI)"
+	exit
+fi
+
+global.bootm.image="/dev/nand0.kernel.bb"
+#global.bootm.oftree="/env/oftree"
+global.linux.bootargs.dyn.root="root=ubi0:rootfs ubi.mtd=nand0.root rootfstype=ubifs"
diff --git a/arch/arm/boards/evk-pro3/env/init/config-board b/arch/arm/boards/evk-pro3/env/init/config-board
new file mode 100644
index 0000000..741b902
--- /dev/null
+++ b/arch/arm/boards/evk-pro3/env/init/config-board
@@ -0,0 +1,8 @@
+#!/bin/sh
+
+# board defaults, do not change in running system. Change /env/config
+# instead
+
+global.hostname=evk-pro3
+global.linux.bootargs.base="console=ttyS0,115200"
+global.boot.default=nand-ubi
diff --git a/arch/arm/boards/evk-pro3/env/init/mtdparts-nand b/arch/arm/boards/evk-pro3/env/init/mtdparts-nand
new file mode 100644
index 0000000..3ac7289
--- /dev/null
+++ b/arch/arm/boards/evk-pro3/env/init/mtdparts-nand
@@ -0,0 +1,11 @@
+#!/bin/sh
+
+if [ "$1" = menu ]; then
+	init-menu-add-entry "$0" "NAND partitions"
+	exit
+fi
+
+mtdparts="0x3C0000(nand0.bootstrap),256k(nand0.barebox)ro,128k(nand0.bareboxenv),3M(nand0.kernel),-(nand0.root)"
+kernelname="atmel_nand"
+
+mtdparts-add -b -d nand0 -k ${kernelname} -p ${mtdparts}
diff --git a/arch/arm/boards/evk-pro3/env/init/usb b/arch/arm/boards/evk-pro3/env/init/usb
new file mode 100644
index 0000000..b682066
--- /dev/null
+++ b/arch/arm/boards/evk-pro3/env/init/usb
@@ -0,0 +1,10 @@
+#!/bin/sh
+
+if [ $at91_udc0.vbus = 1 ]
+then
+	global.autoboot_timeout=16
+	echo
+	echo "enable tty over USB Device, increase the boot delay to ${global.autoboot_timeout}s"
+	usbserial
+	exit
+fi
diff --git a/arch/arm/boards/evk-pro3/init.c b/arch/arm/boards/evk-pro3/init.c
new file mode 100644
index 0000000..7aa65ab
--- /dev/null
+++ b/arch/arm/boards/evk-pro3/init.c
@@ -0,0 +1,233 @@
+/*
+ * Copyright (C) 2007 Sascha Hauer, Pengutronix
+ * Copyright (C) 2013 Fabio Porcedda <fabio.porcedda@gmail.com>, Telit
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ *
+ */
+
+#include <common.h>
+#include <net.h>
+#include <init.h>
+#include <environment.h>
+#include <fec.h>
+#include <asm/armlinux.h>
+#include <generated/mach-types.h>
+#include <partition.h>
+#include <fs.h>
+#include <fcntl.h>
+#include <io.h>
+#include <asm/hardware.h>
+#include <nand.h>
+#include <sizes.h>
+#include <linux/mtd/nand.h>
+#include <mach/board.h>
+#include <mach/at91sam9_smc.h>
+#include <gpio.h>
+#include <mach/io.h>
+#include <mach/at91_pmc.h>
+#include <mach/at91_rstc.h>
+
+#define BOOTSTRAP_SIZE 0x3C0000
+
+static void ek_set_board_type(void)
+{
+	armlinux_set_architecture(MACH_TYPE_GE863);
+}
+
+static struct atmel_nand_data nand_pdata = {
+	.ale		= 21,
+	.cle		= 22,
+	.det_pin	= -EINVAL,
+	.rdy_pin	= AT91_PIN_PC13,
+	.enable_pin	= AT91_PIN_PC14,
+#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
+	.bus_width_16	= 1,
+#else
+	.bus_width_16	= 0,
+#endif
+	.on_flash_bbt	= 1,
+};
+
+static struct sam9_smc_config ek_9260_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 3,
+	.nrd_pulse		= 3,
+	.ncs_write_pulse	= 3,
+	.nwe_pulse		= 3,
+
+	.read_cycle		= 5,
+	.write_cycle		= 5,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
+	.tdf_cycles		= 2,
+};
+
+static struct sam9_smc_config ek_9g20_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 2,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 2,
+
+	.ncs_read_pulse		= 4,
+	.nrd_pulse		= 4,
+	.ncs_write_pulse	= 4,
+	.nwe_pulse		= 4,
+
+	.read_cycle		= 7,
+	.write_cycle		= 7,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
+	.tdf_cycles		= 3,
+};
+
+static void ek_add_device_nand(void)
+{
+	struct sam9_smc_config *smc;
+
+	if (machine_is_at91sam9g20ek())
+		smc = &ek_9g20_nand_smc_config;
+	else
+		smc = &ek_9260_nand_smc_config;
+
+	/* setup bus-width (8 or 16) */
+	if (nand_pdata.bus_width_16)
+		smc->mode |= AT91_SMC_DBW_16;
+	else
+		smc->mode |= AT91_SMC_DBW_8;
+
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(0, 3, smc);
+
+	at91_add_device_nand(&nand_pdata);
+}
+
+static struct at91_ether_platform_data macb_pdata = {
+	.is_rmii = 1,
+	.phy_addr = 0,
+};
+
+static void at91sam9260ek_phy_reset(void)
+{
+	unsigned long rstc;
+	at91_pmc_write(AT91_PMC_PCER, 1 << AT91SAM9260_ID_EMAC);
+
+	at91_set_gpio_input(AT91_PIN_PA14, 0);
+	at91_set_gpio_input(AT91_PIN_PA15, 0);
+	at91_set_gpio_input(AT91_PIN_PA17, 0);
+	at91_set_gpio_input(AT91_PIN_PA25, 0);
+	at91_set_gpio_input(AT91_PIN_PA26, 0);
+	at91_set_gpio_input(AT91_PIN_PA28, 0);
+
+	rstc = at91_sys_read(AT91_RSTC_MR) & AT91_RSTC_ERSTL;
+
+	/* Need to reset PHY -> 500ms reset */
+	at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
+				     (AT91_RSTC_ERSTL & (0x0d << 8)) |
+				     AT91_RSTC_URSTEN);
+
+	at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_EXTRST);
+
+	/* Wait for end hardware reset */
+	while (!(at91_sys_read(AT91_RSTC_SR) & AT91_RSTC_NRSTL));
+
+	/* Restore NRST value */
+	at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
+				     (rstc) |
+				     AT91_RSTC_URSTEN);
+}
+
+/*
+ * MCI (SD/MMC)
+ */
+#if defined(CONFIG_MCI_ATMEL)
+static struct atmel_mci_platform_data __initdata ek_mci_data = {
+	.bus_width	= 4,
+	.slot_b		= 1,
+};
+
+static void ek_usb_add_device_mci(void)
+{
+	if (machine_is_at91sam9g20ek())
+		ek_mci_data.detect_pin = AT91_PIN_PC9;
+
+	at91_add_device_mci(0, &ek_mci_data);
+}
+#else
+static void ek_usb_add_device_mci(void) {}
+#endif
+
+/*
+ * USB Host port
+ */
+static struct at91_usbh_data __initdata ek_usbh_data = {
+	.ports		= 2,
+	.vbus_pin	= { -EINVAL, -EINVAL },
+};
+
+/*
+ * USB Device port
+ */
+static struct at91_udc_data __initdata ek_udc_data = {
+	.vbus_pin	= AT91_PIN_PC4,
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
+};
+
+static int at91sam9260ek_mem_init(void)
+{
+	at91_add_device_sdram(0);
+
+	return 0;
+}
+mem_initcall(at91sam9260ek_mem_init);
+
+static int at91sam9260ek_devices_init(void)
+{
+	ek_add_device_nand();
+	at91sam9260ek_phy_reset();
+	at91_add_device_eth(0, &macb_pdata);
+	at91_add_device_usbh_ohci(&ek_usbh_data);
+	at91_add_device_udc(&ek_udc_data);
+	ek_usb_add_device_mci();
+
+	armlinux_set_bootparams((void *)(AT91_CHIPSELECT_1 + 0x100));
+	ek_set_board_type();
+
+	devfs_add_partition("nand0", 0x00000, BOOTSTRAP_SIZE,
+			    DEVFS_PARTITION_FIXED, "bootstrap_raw");
+	dev_add_bb_dev("bootstrap_raw", "bootstrap");
+	devfs_add_partition("nand0", BOOTSTRAP_SIZE, SZ_256K,
+			    DEVFS_PARTITION_FIXED, "self_raw");
+	dev_add_bb_dev("self_raw", "self0");
+	devfs_add_partition("nand0", BOOTSTRAP_SIZE + SZ_256K, SZ_128K,
+			    DEVFS_PARTITION_FIXED, "env_raw");
+	dev_add_bb_dev("env_raw", "env0");
+	devfs_add_partition("nand0", BOOTSTRAP_SIZE + SZ_256K + SZ_128K,
+			    SZ_128K, DEVFS_PARTITION_FIXED, "env_raw1");
+	dev_add_bb_dev("env_raw1", "env1");
+
+	return 0;
+}
+
+device_initcall(at91sam9260ek_devices_init);
+
+static int at91sam9260ek_console_init(void)
+{
+	at91_register_uart(0, 0);
+	return 0;
+}
+
+console_initcall(at91sam9260ek_console_init);
diff --git a/arch/arm/configs/evk_pro3_defconfig b/arch/arm/configs/evk_pro3_defconfig
new file mode 100644
index 0000000..44168ea
--- /dev/null
+++ b/arch/arm/configs/evk_pro3_defconfig
@@ -0,0 +1,73 @@
+CONFIG_ARCH_AT91SAM9260=y
+CONFIG_MACH_GE863=y
+CONFIG_BAREBOX_MAX_IMAGE_SIZE=0x40000
+CONFIG_AEABI=y
+# CONFIG_CMD_ARM_CPUINFO is not set
+CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y
+CONFIG_PBL_IMAGE=y
+CONFIG_MMU=y
+CONFIG_EXPERIMENTAL=y
+CONFIG_PROMPT="9260-EK:"
+CONFIG_LONGHELP=y
+CONFIG_PROMPT_HUSH_PS2="y"
+CONFIG_HUSH_FANCY_PROMPT=y
+CONFIG_CMDLINE_EDITING=y
+CONFIG_AUTO_COMPLETE=y
+CONFIG_CONSOLE_ACTIVATE_ALL=y
+CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW=y
+CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/evk-pro3/env"
+CONFIG_CMD_EDIT=y
+CONFIG_CMD_SLEEP=y
+CONFIG_CMD_SAVEENV=y
+CONFIG_CMD_EXPORT=y
+CONFIG_CMD_PRINTENV=y
+CONFIG_CMD_READLINE=y
+CONFIG_CMD_TFTP=y
+CONFIG_CMD_ECHO_E=y
+CONFIG_CMD_LOADB=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_FLASH=y
+CONFIG_CMD_UBIFORMAT=y
+CONFIG_CMD_BOOTM_SHOW_TYPE=y
+CONFIG_CMD_BOOTM_INITRD=y
+CONFIG_CMD_BOOTM_OFTREE=y
+CONFIG_CMD_BOOTM_OFTREE_UIMAGE=y
+CONFIG_CMD_UIMAGE=y
+# CONFIG_CMD_BOOTU is not set
+CONFIG_CMD_RESET=y
+CONFIG_CMD_GO=y
+CONFIG_CMD_OFTREE=y
+CONFIG_CMD_MTEST=y
+CONFIG_CMD_MTEST_ALTERNATIVE=y
+CONFIG_CMD_TIMEOUT=y
+CONFIG_CMD_PARTITION=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_LED=y
+CONFIG_CMD_LED_TRIGGER=y
+CONFIG_NET=y
+CONFIG_NET_DHCP=y
+CONFIG_NET_NFS=y
+CONFIG_NET_PING=y
+CONFIG_NET_NETCONSOLE=y
+CONFIG_DRIVER_NET_MACB=y
+# CONFIG_SPI is not set
+CONFIG_MTD=y
+# CONFIG_MTD_OOB_DEVICE is not set
+CONFIG_NAND=y
+# CONFIG_NAND_ECC_HW is not set
+# CONFIG_NAND_ECC_HW_SYNDROME is not set
+# CONFIG_NAND_ECC_HW_NONE is not set
+CONFIG_NAND_ATMEL=y
+CONFIG_UBI=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_DFU=y
+CONFIG_USB_GADGET_SERIAL=y
+CONFIG_MCI=y
+CONFIG_MCI_STARTUP=y
+CONFIG_MCI_ATMEL=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_LED_TRIGGERS=y
+CONFIG_FS_TFTP=y
+CONFIG_FS_FAT=y
+CONFIG_FS_FAT_LFN=y
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index fcba7fb..a319bd3 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -46,6 +46,7 @@ config BOARDINFO
 	default "Calao TNY-A9263" if MACH_TNY_A9263
 	default "Calao TNY-A9G20" if MACH_TNY_A9G20
 	default "Calao QIL-A9260" if MACH_QIL_A9260
+	default "Telit EVK-PRO3" if MACH_GE863
 
 config HAVE_NAND_ATMEL_BUSWIDTH_16
 	bool
@@ -235,6 +236,14 @@ config MACH_USB_A9260
 	  Select this if you are using a Calao Systems USB-A9260.
 	  <http://www.calao-systems.com>
 
+config MACH_GE863
+	bool "Telit EVK-PRO3"
+	select HAVE_NAND_ATMEL_BUSWIDTH_16
+	select HAVE_DEFAULT_ENVIRONMENT_NEW
+	help
+	  Say y here if you are using Telit EVK-PRO3 with GE863-PRO3
+	  <http://www.telit.com>
+
 endchoice
 
 endif
-- 
1.8.0.3


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

^ permalink raw reply	[flat|nested] 3+ messages in thread

* Re: [PATCH] ARM: at91: Add Telit EVK-PRO3 board support
  2013-01-18 16:14 [PATCH] ARM: at91: Add Telit EVK-PRO3 board support Fabio Porcedda
@ 2013-01-19  7:06 ` Jean-Christophe PLAGNIOL-VILLARD
  2013-01-21 12:20   ` Fabio Porcedda
  0 siblings, 1 reply; 3+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-01-19  7:06 UTC (permalink / raw)
  To: Fabio Porcedda; +Cc: barebox

On 17:14 Fri 18 Jan     , Fabio Porcedda wrote:
> http://www.telit.com
> 
> Based on at91sam9260ek board support.
> 
> Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
> ---
>  arch/arm/Makefile                               |   1 +
>  arch/arm/boards/evk-pro3/Makefile               |   1 +
>  arch/arm/boards/evk-pro3/config.h               |   6 +
>  arch/arm/boards/evk-pro3/env/boot/nand-ubi      |  10 +
>  arch/arm/boards/evk-pro3/env/init/config-board  |   8 +
>  arch/arm/boards/evk-pro3/env/init/mtdparts-nand |  11 ++
>  arch/arm/boards/evk-pro3/env/init/usb           |  10 +
>  arch/arm/boards/evk-pro3/init.c                 | 233 ++++++++++++++++++++++++
>  arch/arm/configs/evk_pro3_defconfig             |  73 ++++++++
>  arch/arm/mach-at91/Kconfig                      |   9 +
>  10 files changed, 362 insertions(+)
>  create mode 100644 arch/arm/boards/evk-pro3/Makefile
>  create mode 100644 arch/arm/boards/evk-pro3/config.h
>  create mode 100644 arch/arm/boards/evk-pro3/env/boot/nand-ubi
>  create mode 100644 arch/arm/boards/evk-pro3/env/init/config-board
>  create mode 100644 arch/arm/boards/evk-pro3/env/init/mtdparts-nand
>  create mode 100644 arch/arm/boards/evk-pro3/env/init/usb
>  create mode 100644 arch/arm/boards/evk-pro3/init.c
>  create mode 100644 arch/arm/configs/evk_pro3_defconfig
> 
> diff --git a/arch/arm/Makefile b/arch/arm/Makefile
> index a36adfb..e5c7761 100644
> --- a/arch/arm/Makefile
> +++ b/arch/arm/Makefile
> @@ -94,6 +94,7 @@ board-$(CONFIG_MACH_EUKREA_CPUIMX35)		:= eukrea_cpuimx35
>  board-$(CONFIG_MACH_EUKREA_CPUIMX51SD)		:= eukrea_cpuimx51
>  board-$(CONFIG_MACH_FREESCALE_MX25_3STACK)	:= freescale-mx25-3-stack
>  board-$(CONFIG_MACH_FREESCALE_MX35_3STACK)	:= freescale-mx35-3-stack
> +board-$(CONFIG_MACH_GE863)			:= evk-pro3
>  board-$(CONFIG_MACH_IMX21ADS)			:= imx21ads
>  board-$(CONFIG_MACH_IMX27ADS)			:= imx27ads
>  board-$(CONFIG_MACH_IMX233_OLINUXINO)	:= imx233-olinuxino
> diff --git a/arch/arm/boards/evk-pro3/Makefile b/arch/arm/boards/evk-pro3/Makefile
> new file mode 100644
> index 0000000..eb072c0
> --- /dev/null
> +++ b/arch/arm/boards/evk-pro3/Makefile
> @@ -0,0 +1 @@
> +obj-y += init.o
> diff --git a/arch/arm/boards/evk-pro3/config.h b/arch/arm/boards/evk-pro3/config.h
> new file mode 100644
> index 0000000..7aeff30
> --- /dev/null
> +++ b/arch/arm/boards/evk-pro3/config.h
> @@ -0,0 +1,6 @@
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +#define AT91_MAIN_CLOCK		6000000		/*  6.000 MHz crystal */
> +
> +#endif	/* __CONFIG_H */
> diff --git a/arch/arm/boards/evk-pro3/env/boot/nand-ubi b/arch/arm/boards/evk-pro3/env/boot/nand-ubi
> new file mode 100644
> index 0000000..8115ced
> --- /dev/null
> +++ b/arch/arm/boards/evk-pro3/env/boot/nand-ubi
> @@ -0,0 +1,10 @@
> +#!/bin/sh
> +
> +if [ "$1" = menu ]; then
> +	boot-menu-add-entry "$0" "nand (UBI)"
> +	exit
> +fi
> +
> +global.bootm.image="/dev/nand0.kernel.bb"
> +#global.bootm.oftree="/env/oftree"
> +global.linux.bootargs.dyn.root="root=ubi0:rootfs ubi.mtd=nand0.root rootfstype=ubifs"
> diff --git a/arch/arm/boards/evk-pro3/env/init/config-board b/arch/arm/boards/evk-pro3/env/init/config-board
> new file mode 100644
> index 0000000..741b902
> --- /dev/null
> +++ b/arch/arm/boards/evk-pro3/env/init/config-board
> @@ -0,0 +1,8 @@
> +#!/bin/sh
> +
> +# board defaults, do not change in running system. Change /env/config
> +# instead
> +
> +global.hostname=evk-pro3
> +global.linux.bootargs.base="console=ttyS0,115200"
> +global.boot.default=nand-ubi
> diff --git a/arch/arm/boards/evk-pro3/env/init/mtdparts-nand b/arch/arm/boards/evk-pro3/env/init/mtdparts-nand
> new file mode 100644
> index 0000000..3ac7289
> --- /dev/null
> +++ b/arch/arm/boards/evk-pro3/env/init/mtdparts-nand
> @@ -0,0 +1,11 @@
> +#!/bin/sh
> +
> +if [ "$1" = menu ]; then
> +	init-menu-add-entry "$0" "NAND partitions"
> +	exit
> +fi
> +
> +mtdparts="0x3C0000(nand0.bootstrap),256k(nand0.barebox)ro,128k(nand0.bareboxenv),3M(nand0.kernel),-(nand0.root)"
> +kernelname="atmel_nand"
> +
> +mtdparts-add -b -d nand0 -k ${kernelname} -p ${mtdparts}
> diff --git a/arch/arm/boards/evk-pro3/env/init/usb b/arch/arm/boards/evk-pro3/env/init/usb
> new file mode 100644
> index 0000000..b682066
> --- /dev/null
> +++ b/arch/arm/boards/evk-pro3/env/init/usb
> @@ -0,0 +1,10 @@
> +#!/bin/sh
> +
> +if [ $at91_udc0.vbus = 1 ]
> +then
> +	global.autoboot_timeout=16
> +	echo
> +	echo "enable tty over USB Device, increase the boot delay to ${global.autoboot_timeout}s"
> +	usbserial
> +	exit
> +fi
> diff --git a/arch/arm/boards/evk-pro3/init.c b/arch/arm/boards/evk-pro3/init.c
> new file mode 100644
> index 0000000..7aa65ab
> --- /dev/null
> +++ b/arch/arm/boards/evk-pro3/init.c
> @@ -0,0 +1,233 @@
> +/*
> + * Copyright (C) 2007 Sascha Hauer, Pengutronix
> + * Copyright (C) 2013 Fabio Porcedda <fabio.porcedda@gmail.com>, Telit
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + *
> + */
> +
> +#include <common.h>
> +#include <net.h>
> +#include <init.h>
> +#include <environment.h>
> +#include <fec.h>
> +#include <asm/armlinux.h>
> +#include <generated/mach-types.h>
> +#include <partition.h>
> +#include <fs.h>
> +#include <fcntl.h>
> +#include <io.h>
> +#include <asm/hardware.h>
> +#include <nand.h>
> +#include <sizes.h>
> +#include <linux/mtd/nand.h>
> +#include <mach/board.h>
> +#include <mach/at91sam9_smc.h>
> +#include <gpio.h>
> +#include <mach/io.h>
> +#include <mach/at91_pmc.h>
> +#include <mach/at91_rstc.h>
> +
> +#define BOOTSTRAP_SIZE 0x3C0000
> +
> +static void ek_set_board_type(void)
ek_ means evaluation kit
and you can drop this function 
> +{
> +	armlinux_set_architecture(MACH_TYPE_GE863);
> +}
> +
> +static struct atmel_nand_data nand_pdata = {
> +	.ale		= 21,
> +	.cle		= 22,
> +	.det_pin	= -EINVAL,
> +	.rdy_pin	= AT91_PIN_PC13,
> +	.enable_pin	= AT91_PIN_PC14,
> +#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
> +	.bus_width_16	= 1,
> +#else
> +	.bus_width_16	= 0,
> +#endif
you can drop the 16 width
> +	.on_flash_bbt	= 1,
> +};
> +
> +static struct sam9_smc_config ek_9260_nand_smc_config = {
> +	.ncs_read_setup		= 0,
> +	.nrd_setup		= 1,
> +	.ncs_write_setup	= 0,
> +	.nwe_setup		= 1,
> +
> +	.ncs_read_pulse		= 3,
> +	.nrd_pulse		= 3,
> +	.ncs_write_pulse	= 3,
> +	.nwe_pulse		= 3,
> +
> +	.read_cycle		= 5,
> +	.write_cycle		= 5,
> +
> +	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
> +	.tdf_cycles		= 2,
> +};
> +
> +static struct sam9_smc_config ek_9g20_nand_smc_config = {
> +	.ncs_read_setup		= 0,
> +	.nrd_setup		= 2,
> +	.ncs_write_setup	= 0,
> +	.nwe_setup		= 2,
> +
> +	.ncs_read_pulse		= 4,
> +	.nrd_pulse		= 4,
> +	.ncs_write_pulse	= 4,
> +	.nwe_pulse		= 4,
> +
> +	.read_cycle		= 7,
> +	.write_cycle		= 7,
> +
> +	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
> +	.tdf_cycles		= 3,
> +};
> +
> +static void ek_add_device_nand(void)
> +{
> +	struct sam9_smc_config *smc;
> +
> +	if (machine_is_at91sam9g20ek())
> +		smc = &ek_9g20_nand_smc_config;
> +	else
> +		smc = &ek_9260_nand_smc_config;
> +
you are not a atmel ref board please clean it
> +	/* setup bus-width (8 or 16) */
> +	if (nand_pdata.bus_width_16)
> +		smc->mode |= AT91_SMC_DBW_16;
> +	else
> +		smc->mode |= AT91_SMC_DBW_8;
> +
> +	/* configure chip-select 3 (NAND) */
> +	sam9_smc_configure(0, 3, smc);
> +
> +	at91_add_device_nand(&nand_pdata);
> +}
> +
> +static struct at91_ether_platform_data macb_pdata = {
> +	.is_rmii = 1,
> +	.phy_addr = 0,
> +};
> +
> +static void at91sam9260ek_phy_reset(void)
> +{
> +	unsigned long rstc;
> +	at91_pmc_write(AT91_PMC_PCER, 1 << AT91SAM9260_ID_EMAC);
nack

use clk framework

I cleanup this already on the mainline
> +
> +	at91_set_gpio_input(AT91_PIN_PA14, 0);
> +	at91_set_gpio_input(AT91_PIN_PA15, 0);
> +	at91_set_gpio_input(AT91_PIN_PA17, 0);
> +	at91_set_gpio_input(AT91_PIN_PA25, 0);
> +	at91_set_gpio_input(AT91_PIN_PA26, 0);
> +	at91_set_gpio_input(AT91_PIN_PA28, 0);
> +
> +	rstc = at91_sys_read(AT91_RSTC_MR) & AT91_RSTC_ERSTL;
> +
> +	/* Need to reset PHY -> 500ms reset */
> +	at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
> +				     (AT91_RSTC_ERSTL & (0x0d << 8)) |
> +				     AT91_RSTC_URSTEN);
> +
> +	at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_EXTRST);
> +
> +	/* Wait for end hardware reset */
> +	while (!(at91_sys_read(AT91_RSTC_SR) & AT91_RSTC_NRSTL));
> +
> +	/* Restore NRST value */
> +	at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
> +				     (rstc) |
> +				     AT91_RSTC_URSTEN);
> +}
> +
> +/*
> + * MCI (SD/MMC)
> + */
> +#if defined(CONFIG_MCI_ATMEL)
> +static struct atmel_mci_platform_data __initdata ek_mci_data = {
> +	.bus_width	= 4,
> +	.slot_b		= 1,
> +};
> +
> +static void ek_usb_add_device_mci(void)
> +{
> +	if (machine_is_at91sam9g20ek())
> +		ek_mci_data.detect_pin = AT91_PIN_PC9;
> +
> +	at91_add_device_mci(0, &ek_mci_data);
> +}
> +#else
> +static void ek_usb_add_device_mci(void) {}
> +#endif
> +
> +/*
> + * USB Host port
> + */
> +static struct at91_usbh_data __initdata ek_usbh_data = {
> +	.ports		= 2,
> +	.vbus_pin	= { -EINVAL, -EINVAL },
> +};
> +
> +/*
> + * USB Device port
> + */
> +static struct at91_udc_data __initdata ek_udc_data = {
> +	.vbus_pin	= AT91_PIN_PC4,
> +	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
> +};
> +
> +static int at91sam9260ek_mem_init(void)
> +{
> +	at91_add_device_sdram(0);
> +
> +	return 0;
> +}
> +mem_initcall(at91sam9260ek_mem_init);
> +
> +static int at91sam9260ek_devices_init(void)
> +{
> +	ek_add_device_nand();
> +	at91sam9260ek_phy_reset();
> +	at91_add_device_eth(0, &macb_pdata);
> +	at91_add_device_usbh_ohci(&ek_usbh_data);
> +	at91_add_device_udc(&ek_udc_data);
> +	ek_usb_add_device_mci();
> +
> +	armlinux_set_bootparams((void *)(AT91_CHIPSELECT_1 + 0x100));
> +	ek_set_board_type();
> +
> +	devfs_add_partition("nand0", 0x00000, BOOTSTRAP_SIZE,
> +			    DEVFS_PARTITION_FIXED, "bootstrap_raw");
> +	dev_add_bb_dev("bootstrap_raw", "bootstrap");
> +	devfs_add_partition("nand0", BOOTSTRAP_SIZE, SZ_256K,
> +			    DEVFS_PARTITION_FIXED, "self_raw");
> +	dev_add_bb_dev("self_raw", "self0");
> +	devfs_add_partition("nand0", BOOTSTRAP_SIZE + SZ_256K, SZ_128K,
> +			    DEVFS_PARTITION_FIXED, "env_raw");
> +	dev_add_bb_dev("env_raw", "env0");
> +	devfs_add_partition("nand0", BOOTSTRAP_SIZE + SZ_256K + SZ_128K,
> +			    SZ_128K, DEVFS_PARTITION_FIXED, "env_raw1");
> +	dev_add_bb_dev("env_raw1", "env1");
> +
> +	return 0;
> +}
> +
> +device_initcall(at91sam9260ek_devices_init);
> +
> +static int at91sam9260ek_console_init(void)
> +{
> +	at91_register_uart(0, 0);
> +	return 0;
> +}
> +
> +console_initcall(at91sam9260ek_console_init);
> diff --git a/arch/arm/configs/evk_pro3_defconfig b/arch/arm/configs/evk_pro3_defconfig
> new file mode 100644
> index 0000000..44168ea
> --- /dev/null
> +++ b/arch/arm/configs/evk_pro3_defconfig
> @@ -0,0 +1,73 @@
> +CONFIG_ARCH_AT91SAM9260=y
> +CONFIG_MACH_GE863=y
> +CONFIG_BAREBOX_MAX_IMAGE_SIZE=0x40000
> +CONFIG_AEABI=y
> +# CONFIG_CMD_ARM_CPUINFO is not set
> +CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y
> +CONFIG_PBL_IMAGE=y
> +CONFIG_MMU=y
> +CONFIG_EXPERIMENTAL=y
> +CONFIG_PROMPT="9260-EK:"
> +CONFIG_LONGHELP=y
> +CONFIG_PROMPT_HUSH_PS2="y"
> +CONFIG_HUSH_FANCY_PROMPT=y
> +CONFIG_CMDLINE_EDITING=y
> +CONFIG_AUTO_COMPLETE=y
> +CONFIG_CONSOLE_ACTIVATE_ALL=y
> +CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW=y
> +CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/evk-pro3/env"
> +CONFIG_CMD_EDIT=y
> +CONFIG_CMD_SLEEP=y
> +CONFIG_CMD_SAVEENV=y
> +CONFIG_CMD_EXPORT=y
> +CONFIG_CMD_PRINTENV=y
> +CONFIG_CMD_READLINE=y
> +CONFIG_CMD_TFTP=y
> +CONFIG_CMD_ECHO_E=y
> +CONFIG_CMD_LOADB=y
> +CONFIG_CMD_MEMINFO=y
> +CONFIG_CMD_FLASH=y
> +CONFIG_CMD_UBIFORMAT=y
> +CONFIG_CMD_BOOTM_SHOW_TYPE=y
> +CONFIG_CMD_BOOTM_INITRD=y
> +CONFIG_CMD_BOOTM_OFTREE=y
> +CONFIG_CMD_BOOTM_OFTREE_UIMAGE=y
> +CONFIG_CMD_UIMAGE=y
> +# CONFIG_CMD_BOOTU is not set
> +CONFIG_CMD_RESET=y
> +CONFIG_CMD_GO=y
> +CONFIG_CMD_OFTREE=y
> +CONFIG_CMD_MTEST=y
> +CONFIG_CMD_MTEST_ALTERNATIVE=y
> +CONFIG_CMD_TIMEOUT=y
> +CONFIG_CMD_PARTITION=y
> +CONFIG_CMD_GPIO=y
> +CONFIG_CMD_LED=y
> +CONFIG_CMD_LED_TRIGGER=y
> +CONFIG_NET=y
> +CONFIG_NET_DHCP=y
> +CONFIG_NET_NFS=y
> +CONFIG_NET_PING=y
> +CONFIG_NET_NETCONSOLE=y
> +CONFIG_DRIVER_NET_MACB=y
> +# CONFIG_SPI is not set
> +CONFIG_MTD=y
> +# CONFIG_MTD_OOB_DEVICE is not set
> +CONFIG_NAND=y
> +# CONFIG_NAND_ECC_HW is not set
> +# CONFIG_NAND_ECC_HW_SYNDROME is not set
> +# CONFIG_NAND_ECC_HW_NONE is not set
> +CONFIG_NAND_ATMEL=y
> +CONFIG_UBI=y
> +CONFIG_USB_GADGET=y
> +CONFIG_USB_GADGET_DFU=y
> +CONFIG_USB_GADGET_SERIAL=y
> +CONFIG_MCI=y
> +CONFIG_MCI_STARTUP=y
> +CONFIG_MCI_ATMEL=y
> +CONFIG_LED=y
> +CONFIG_LED_GPIO=y
> +CONFIG_LED_TRIGGERS=y
> +CONFIG_FS_TFTP=y
> +CONFIG_FS_FAT=y
> +CONFIG_FS_FAT_LFN=y
> diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
> index fcba7fb..a319bd3 100644
> --- a/arch/arm/mach-at91/Kconfig
> +++ b/arch/arm/mach-at91/Kconfig
> @@ -46,6 +46,7 @@ config BOARDINFO
>  	default "Calao TNY-A9263" if MACH_TNY_A9263
>  	default "Calao TNY-A9G20" if MACH_TNY_A9G20
>  	default "Calao QIL-A9260" if MACH_QIL_A9260
> +	default "Telit EVK-PRO3" if MACH_GE863
>  
>  config HAVE_NAND_ATMEL_BUSWIDTH_16
>  	bool
> @@ -235,6 +236,14 @@ config MACH_USB_A9260
>  	  Select this if you are using a Calao Systems USB-A9260.
>  	  <http://www.calao-systems.com>
>  
> +config MACH_GE863
> +	bool "Telit EVK-PRO3"
> +	select HAVE_NAND_ATMEL_BUSWIDTH_16
> +	select HAVE_DEFAULT_ENVIRONMENT_NEW
> +	help
> +	  Say y here if you are using Telit EVK-PRO3 with GE863-PRO3
> +	  <http://www.telit.com>
> +
>  endchoice
>  
>  endif
> -- 
> 1.8.0.3
> 
> 
> _______________________________________________
> barebox mailing list
> barebox@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

^ permalink raw reply	[flat|nested] 3+ messages in thread

* Re: [PATCH] ARM: at91: Add Telit EVK-PRO3 board support
  2013-01-19  7:06 ` Jean-Christophe PLAGNIOL-VILLARD
@ 2013-01-21 12:20   ` Fabio Porcedda
  0 siblings, 0 replies; 3+ messages in thread
From: Fabio Porcedda @ 2013-01-21 12:20 UTC (permalink / raw)
  To: Jean-Christophe PLAGNIOL-VILLARD; +Cc: barebox

Hi Jean-Christophe,
thanks for reviewing.

On Sat, Jan 19, 2013 at 8:06 AM, Jean-Christophe PLAGNIOL-VILLARD
<plagnioj@jcrosoft.com> wrote:
> On 17:14 Fri 18 Jan     , Fabio Porcedda wrote:
>> http://www.telit.com
>>
>> Based on at91sam9260ek board support.
>>
>> Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
>> ---
>>  arch/arm/Makefile                               |   1 +
>>  arch/arm/boards/evk-pro3/Makefile               |   1 +
>>  arch/arm/boards/evk-pro3/config.h               |   6 +
>>  arch/arm/boards/evk-pro3/env/boot/nand-ubi      |  10 +
>>  arch/arm/boards/evk-pro3/env/init/config-board  |   8 +
>>  arch/arm/boards/evk-pro3/env/init/mtdparts-nand |  11 ++
>>  arch/arm/boards/evk-pro3/env/init/usb           |  10 +
>>  arch/arm/boards/evk-pro3/init.c                 | 233 ++++++++++++++++++++++++
>>  arch/arm/configs/evk_pro3_defconfig             |  73 ++++++++
>>  arch/arm/mach-at91/Kconfig                      |   9 +
>>  10 files changed, 362 insertions(+)
>>  create mode 100644 arch/arm/boards/evk-pro3/Makefile
>>  create mode 100644 arch/arm/boards/evk-pro3/config.h
>>  create mode 100644 arch/arm/boards/evk-pro3/env/boot/nand-ubi
>>  create mode 100644 arch/arm/boards/evk-pro3/env/init/config-board
>>  create mode 100644 arch/arm/boards/evk-pro3/env/init/mtdparts-nand
>>  create mode 100644 arch/arm/boards/evk-pro3/env/init/usb
>>  create mode 100644 arch/arm/boards/evk-pro3/init.c
>>  create mode 100644 arch/arm/configs/evk_pro3_defconfig
>>
>> diff --git a/arch/arm/Makefile b/arch/arm/Makefile
>> index a36adfb..e5c7761 100644
>> --- a/arch/arm/Makefile
>> +++ b/arch/arm/Makefile
>> @@ -94,6 +94,7 @@ board-$(CONFIG_MACH_EUKREA_CPUIMX35)                := eukrea_cpuimx35
>>  board-$(CONFIG_MACH_EUKREA_CPUIMX51SD)               := eukrea_cpuimx51
>>  board-$(CONFIG_MACH_FREESCALE_MX25_3STACK)   := freescale-mx25-3-stack
>>  board-$(CONFIG_MACH_FREESCALE_MX35_3STACK)   := freescale-mx35-3-stack
>> +board-$(CONFIG_MACH_GE863)                   := evk-pro3
>>  board-$(CONFIG_MACH_IMX21ADS)                        := imx21ads
>>  board-$(CONFIG_MACH_IMX27ADS)                        := imx27ads
>>  board-$(CONFIG_MACH_IMX233_OLINUXINO)        := imx233-olinuxino
>> diff --git a/arch/arm/boards/evk-pro3/Makefile b/arch/arm/boards/evk-pro3/Makefile
>> new file mode 100644
>> index 0000000..eb072c0
>> --- /dev/null
>> +++ b/arch/arm/boards/evk-pro3/Makefile
>> @@ -0,0 +1 @@
>> +obj-y += init.o
>> diff --git a/arch/arm/boards/evk-pro3/config.h b/arch/arm/boards/evk-pro3/config.h
>> new file mode 100644
>> index 0000000..7aeff30
>> --- /dev/null
>> +++ b/arch/arm/boards/evk-pro3/config.h
>> @@ -0,0 +1,6 @@
>> +#ifndef __CONFIG_H
>> +#define __CONFIG_H
>> +
>> +#define AT91_MAIN_CLOCK              6000000         /*  6.000 MHz crystal */
>> +
>> +#endif       /* __CONFIG_H */
>> diff --git a/arch/arm/boards/evk-pro3/env/boot/nand-ubi b/arch/arm/boards/evk-pro3/env/boot/nand-ubi
>> new file mode 100644
>> index 0000000..8115ced
>> --- /dev/null
>> +++ b/arch/arm/boards/evk-pro3/env/boot/nand-ubi
>> @@ -0,0 +1,10 @@
>> +#!/bin/sh
>> +
>> +if [ "$1" = menu ]; then
>> +     boot-menu-add-entry "$0" "nand (UBI)"
>> +     exit
>> +fi
>> +
>> +global.bootm.image="/dev/nand0.kernel.bb"
>> +#global.bootm.oftree="/env/oftree"
>> +global.linux.bootargs.dyn.root="root=ubi0:rootfs ubi.mtd=nand0.root rootfstype=ubifs"
>> diff --git a/arch/arm/boards/evk-pro3/env/init/config-board b/arch/arm/boards/evk-pro3/env/init/config-board
>> new file mode 100644
>> index 0000000..741b902
>> --- /dev/null
>> +++ b/arch/arm/boards/evk-pro3/env/init/config-board
>> @@ -0,0 +1,8 @@
>> +#!/bin/sh
>> +
>> +# board defaults, do not change in running system. Change /env/config
>> +# instead
>> +
>> +global.hostname=evk-pro3
>> +global.linux.bootargs.base="console=ttyS0,115200"
>> +global.boot.default=nand-ubi
>> diff --git a/arch/arm/boards/evk-pro3/env/init/mtdparts-nand b/arch/arm/boards/evk-pro3/env/init/mtdparts-nand
>> new file mode 100644
>> index 0000000..3ac7289
>> --- /dev/null
>> +++ b/arch/arm/boards/evk-pro3/env/init/mtdparts-nand
>> @@ -0,0 +1,11 @@
>> +#!/bin/sh
>> +
>> +if [ "$1" = menu ]; then
>> +     init-menu-add-entry "$0" "NAND partitions"
>> +     exit
>> +fi
>> +
>> +mtdparts="0x3C0000(nand0.bootstrap),256k(nand0.barebox)ro,128k(nand0.bareboxenv),3M(nand0.kernel),-(nand0.root)"
>> +kernelname="atmel_nand"
>> +
>> +mtdparts-add -b -d nand0 -k ${kernelname} -p ${mtdparts}
>> diff --git a/arch/arm/boards/evk-pro3/env/init/usb b/arch/arm/boards/evk-pro3/env/init/usb
>> new file mode 100644
>> index 0000000..b682066
>> --- /dev/null
>> +++ b/arch/arm/boards/evk-pro3/env/init/usb
>> @@ -0,0 +1,10 @@
>> +#!/bin/sh
>> +
>> +if [ $at91_udc0.vbus = 1 ]
>> +then
>> +     global.autoboot_timeout=16
>> +     echo
>> +     echo "enable tty over USB Device, increase the boot delay to ${global.autoboot_timeout}s"
>> +     usbserial
>> +     exit
>> +fi
>> diff --git a/arch/arm/boards/evk-pro3/init.c b/arch/arm/boards/evk-pro3/init.c
>> new file mode 100644
>> index 0000000..7aa65ab
>> --- /dev/null
>> +++ b/arch/arm/boards/evk-pro3/init.c
>> @@ -0,0 +1,233 @@
>> +/*
>> + * Copyright (C) 2007 Sascha Hauer, Pengutronix
>> + * Copyright (C) 2013 Fabio Porcedda <fabio.porcedda@gmail.com>, Telit
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation; either version 2 of
>> + * the License, or (at your option) any later version.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + * GNU General Public License for more details.
>> + *
>> + *
>> + */
>> +
>> +#include <common.h>
>> +#include <net.h>
>> +#include <init.h>
>> +#include <environment.h>
>> +#include <fec.h>
>> +#include <asm/armlinux.h>
>> +#include <generated/mach-types.h>
>> +#include <partition.h>
>> +#include <fs.h>
>> +#include <fcntl.h>
>> +#include <io.h>
>> +#include <asm/hardware.h>
>> +#include <nand.h>
>> +#include <sizes.h>
>> +#include <linux/mtd/nand.h>
>> +#include <mach/board.h>
>> +#include <mach/at91sam9_smc.h>
>> +#include <gpio.h>
>> +#include <mach/io.h>
>> +#include <mach/at91_pmc.h>
>> +#include <mach/at91_rstc.h>
>> +
>> +#define BOOTSTRAP_SIZE 0x3C0000
>> +
>> +static void ek_set_board_type(void)
> ek_ means evaluation kit
> and you can drop this function

Ok, done in v2.

>> +{
>> +     armlinux_set_architecture(MACH_TYPE_GE863);
>> +}
>> +
>> +static struct atmel_nand_data nand_pdata = {
>> +     .ale            = 21,
>> +     .cle            = 22,
>> +     .det_pin        = -EINVAL,
>> +     .rdy_pin        = AT91_PIN_PC13,
>> +     .enable_pin     = AT91_PIN_PC14,
>> +#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
>> +     .bus_width_16   = 1,
>> +#else
>> +     .bus_width_16   = 0,
>> +#endif
> you can drop the 16 width

Ok, done in v2.

>> +     .on_flash_bbt   = 1,
>> +};
>> +
>> +static struct sam9_smc_config ek_9260_nand_smc_config = {
>> +     .ncs_read_setup         = 0,
>> +     .nrd_setup              = 1,
>> +     .ncs_write_setup        = 0,
>> +     .nwe_setup              = 1,
>> +
>> +     .ncs_read_pulse         = 3,
>> +     .nrd_pulse              = 3,
>> +     .ncs_write_pulse        = 3,
>> +     .nwe_pulse              = 3,
>> +
>> +     .read_cycle             = 5,
>> +     .write_cycle            = 5,
>> +
>> +     .mode                   = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
>> +     .tdf_cycles             = 2,
>> +};
>> +
>> +static struct sam9_smc_config ek_9g20_nand_smc_config = {
>> +     .ncs_read_setup         = 0,
>> +     .nrd_setup              = 2,
>> +     .ncs_write_setup        = 0,
>> +     .nwe_setup              = 2,
>> +
>> +     .ncs_read_pulse         = 4,
>> +     .nrd_pulse              = 4,
>> +     .ncs_write_pulse        = 4,
>> +     .nwe_pulse              = 4,
>> +
>> +     .read_cycle             = 7,
>> +     .write_cycle            = 7,
>> +
>> +     .mode                   = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
>> +     .tdf_cycles             = 3,
>> +};
>> +
>> +static void ek_add_device_nand(void)
>> +{
>> +     struct sam9_smc_config *smc;
>> +
>> +     if (machine_is_at91sam9g20ek())
>> +             smc = &ek_9g20_nand_smc_config;
>> +     else
>> +             smc = &ek_9260_nand_smc_config;
>> +
> you are not a atmel ref board please clean it

Ok, done in v2.

>> +     /* setup bus-width (8 or 16) */
>> +     if (nand_pdata.bus_width_16)
>> +             smc->mode |= AT91_SMC_DBW_16;
>> +     else
>> +             smc->mode |= AT91_SMC_DBW_8;
>> +
>> +     /* configure chip-select 3 (NAND) */
>> +     sam9_smc_configure(0, 3, smc);
>> +
>> +     at91_add_device_nand(&nand_pdata);
>> +}
>> +
>> +static struct at91_ether_platform_data macb_pdata = {
>> +     .is_rmii = 1,
>> +     .phy_addr = 0,
>> +};
>> +
>> +static void at91sam9260ek_phy_reset(void)
>> +{
>> +     unsigned long rstc;
>> +     at91_pmc_write(AT91_PMC_PCER, 1 << AT91SAM9260_ID_EMAC);
> nack
>
> use clk framework
>
> I cleanup this already on the mainline

Ok, done in v2.

>> +
>> +     at91_set_gpio_input(AT91_PIN_PA14, 0);
>> +     at91_set_gpio_input(AT91_PIN_PA15, 0);
>> +     at91_set_gpio_input(AT91_PIN_PA17, 0);
>> +     at91_set_gpio_input(AT91_PIN_PA25, 0);
>> +     at91_set_gpio_input(AT91_PIN_PA26, 0);
>> +     at91_set_gpio_input(AT91_PIN_PA28, 0);
>> +
>> +     rstc = at91_sys_read(AT91_RSTC_MR) & AT91_RSTC_ERSTL;
>> +
>> +     /* Need to reset PHY -> 500ms reset */
>> +     at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
>> +                                  (AT91_RSTC_ERSTL & (0x0d << 8)) |
>> +                                  AT91_RSTC_URSTEN);
>> +
>> +     at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_EXTRST);
>> +
>> +     /* Wait for end hardware reset */
>> +     while (!(at91_sys_read(AT91_RSTC_SR) & AT91_RSTC_NRSTL));
>> +
>> +     /* Restore NRST value */
>> +     at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
>> +                                  (rstc) |
>> +                                  AT91_RSTC_URSTEN);
>> +}
>> +
>> +/*
>> + * MCI (SD/MMC)
>> + */
>> +#if defined(CONFIG_MCI_ATMEL)
>> +static struct atmel_mci_platform_data __initdata ek_mci_data = {
>> +     .bus_width      = 4,
>> +     .slot_b         = 1,
>> +};
>> +
>> +static void ek_usb_add_device_mci(void)
>> +{
>> +     if (machine_is_at91sam9g20ek())
>> +             ek_mci_data.detect_pin = AT91_PIN_PC9;
>> +
>> +     at91_add_device_mci(0, &ek_mci_data);
>> +}
>> +#else
>> +static void ek_usb_add_device_mci(void) {}
>> +#endif
>> +
>> +/*
>> + * USB Host port
>> + */
>> +static struct at91_usbh_data __initdata ek_usbh_data = {
>> +     .ports          = 2,
>> +     .vbus_pin       = { -EINVAL, -EINVAL },
>> +};
>> +
>> +/*
>> + * USB Device port
>> + */
>> +static struct at91_udc_data __initdata ek_udc_data = {
>> +     .vbus_pin       = AT91_PIN_PC4,
>> +     .pullup_pin     = -EINVAL,              /* pull-up driven by UDC */
>> +};
>> +
>> +static int at91sam9260ek_mem_init(void)
>> +{
>> +     at91_add_device_sdram(0);
>> +
>> +     return 0;
>> +}
>> +mem_initcall(at91sam9260ek_mem_init);
>> +
>> +static int at91sam9260ek_devices_init(void)
>> +{
>> +     ek_add_device_nand();
>> +     at91sam9260ek_phy_reset();
>> +     at91_add_device_eth(0, &macb_pdata);
>> +     at91_add_device_usbh_ohci(&ek_usbh_data);
>> +     at91_add_device_udc(&ek_udc_data);
>> +     ek_usb_add_device_mci();
>> +
>> +     armlinux_set_bootparams((void *)(AT91_CHIPSELECT_1 + 0x100));
>> +     ek_set_board_type();
>> +
>> +     devfs_add_partition("nand0", 0x00000, BOOTSTRAP_SIZE,
>> +                         DEVFS_PARTITION_FIXED, "bootstrap_raw");
>> +     dev_add_bb_dev("bootstrap_raw", "bootstrap");
>> +     devfs_add_partition("nand0", BOOTSTRAP_SIZE, SZ_256K,
>> +                         DEVFS_PARTITION_FIXED, "self_raw");
>> +     dev_add_bb_dev("self_raw", "self0");
>> +     devfs_add_partition("nand0", BOOTSTRAP_SIZE + SZ_256K, SZ_128K,
>> +                         DEVFS_PARTITION_FIXED, "env_raw");
>> +     dev_add_bb_dev("env_raw", "env0");
>> +     devfs_add_partition("nand0", BOOTSTRAP_SIZE + SZ_256K + SZ_128K,
>> +                         SZ_128K, DEVFS_PARTITION_FIXED, "env_raw1");
>> +     dev_add_bb_dev("env_raw1", "env1");
>> +
>> +     return 0;
>> +}
>> +
>> +device_initcall(at91sam9260ek_devices_init);
>> +
>> +static int at91sam9260ek_console_init(void)
>> +{
>> +     at91_register_uart(0, 0);
>> +     return 0;
>> +}
>> +
>> +console_initcall(at91sam9260ek_console_init);
>> diff --git a/arch/arm/configs/evk_pro3_defconfig b/arch/arm/configs/evk_pro3_defconfig
>> new file mode 100644
>> index 0000000..44168ea
>> --- /dev/null
>> +++ b/arch/arm/configs/evk_pro3_defconfig
>> @@ -0,0 +1,73 @@
>> +CONFIG_ARCH_AT91SAM9260=y
>> +CONFIG_MACH_GE863=y
>> +CONFIG_BAREBOX_MAX_IMAGE_SIZE=0x40000
>> +CONFIG_AEABI=y
>> +# CONFIG_CMD_ARM_CPUINFO is not set
>> +CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y
>> +CONFIG_PBL_IMAGE=y
>> +CONFIG_MMU=y
>> +CONFIG_EXPERIMENTAL=y
>> +CONFIG_PROMPT="9260-EK:"
>> +CONFIG_LONGHELP=y
>> +CONFIG_PROMPT_HUSH_PS2="y"
>> +CONFIG_HUSH_FANCY_PROMPT=y
>> +CONFIG_CMDLINE_EDITING=y
>> +CONFIG_AUTO_COMPLETE=y
>> +CONFIG_CONSOLE_ACTIVATE_ALL=y
>> +CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW=y
>> +CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/evk-pro3/env"
>> +CONFIG_CMD_EDIT=y
>> +CONFIG_CMD_SLEEP=y
>> +CONFIG_CMD_SAVEENV=y
>> +CONFIG_CMD_EXPORT=y
>> +CONFIG_CMD_PRINTENV=y
>> +CONFIG_CMD_READLINE=y
>> +CONFIG_CMD_TFTP=y
>> +CONFIG_CMD_ECHO_E=y
>> +CONFIG_CMD_LOADB=y
>> +CONFIG_CMD_MEMINFO=y
>> +CONFIG_CMD_FLASH=y
>> +CONFIG_CMD_UBIFORMAT=y
>> +CONFIG_CMD_BOOTM_SHOW_TYPE=y
>> +CONFIG_CMD_BOOTM_INITRD=y
>> +CONFIG_CMD_BOOTM_OFTREE=y
>> +CONFIG_CMD_BOOTM_OFTREE_UIMAGE=y
>> +CONFIG_CMD_UIMAGE=y
>> +# CONFIG_CMD_BOOTU is not set
>> +CONFIG_CMD_RESET=y
>> +CONFIG_CMD_GO=y
>> +CONFIG_CMD_OFTREE=y
>> +CONFIG_CMD_MTEST=y
>> +CONFIG_CMD_MTEST_ALTERNATIVE=y
>> +CONFIG_CMD_TIMEOUT=y
>> +CONFIG_CMD_PARTITION=y
>> +CONFIG_CMD_GPIO=y
>> +CONFIG_CMD_LED=y
>> +CONFIG_CMD_LED_TRIGGER=y
>> +CONFIG_NET=y
>> +CONFIG_NET_DHCP=y
>> +CONFIG_NET_NFS=y
>> +CONFIG_NET_PING=y
>> +CONFIG_NET_NETCONSOLE=y
>> +CONFIG_DRIVER_NET_MACB=y
>> +# CONFIG_SPI is not set
>> +CONFIG_MTD=y
>> +# CONFIG_MTD_OOB_DEVICE is not set
>> +CONFIG_NAND=y
>> +# CONFIG_NAND_ECC_HW is not set
>> +# CONFIG_NAND_ECC_HW_SYNDROME is not set
>> +# CONFIG_NAND_ECC_HW_NONE is not set
>> +CONFIG_NAND_ATMEL=y
>> +CONFIG_UBI=y
>> +CONFIG_USB_GADGET=y
>> +CONFIG_USB_GADGET_DFU=y
>> +CONFIG_USB_GADGET_SERIAL=y
>> +CONFIG_MCI=y
>> +CONFIG_MCI_STARTUP=y
>> +CONFIG_MCI_ATMEL=y
>> +CONFIG_LED=y
>> +CONFIG_LED_GPIO=y
>> +CONFIG_LED_TRIGGERS=y
>> +CONFIG_FS_TFTP=y
>> +CONFIG_FS_FAT=y
>> +CONFIG_FS_FAT_LFN=y
>> diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
>> index fcba7fb..a319bd3 100644
>> --- a/arch/arm/mach-at91/Kconfig
>> +++ b/arch/arm/mach-at91/Kconfig
>> @@ -46,6 +46,7 @@ config BOARDINFO
>>       default "Calao TNY-A9263" if MACH_TNY_A9263
>>       default "Calao TNY-A9G20" if MACH_TNY_A9G20
>>       default "Calao QIL-A9260" if MACH_QIL_A9260
>> +     default "Telit EVK-PRO3" if MACH_GE863
>>
>>  config HAVE_NAND_ATMEL_BUSWIDTH_16
>>       bool
>> @@ -235,6 +236,14 @@ config MACH_USB_A9260
>>         Select this if you are using a Calao Systems USB-A9260.
>>         <http://www.calao-systems.com>
>>
>> +config MACH_GE863
>> +     bool "Telit EVK-PRO3"
>> +     select HAVE_NAND_ATMEL_BUSWIDTH_16
>> +     select HAVE_DEFAULT_ENVIRONMENT_NEW
>> +     help
>> +       Say y here if you are using Telit EVK-PRO3 with GE863-PRO3
>> +       <http://www.telit.com>
>> +
>>  endchoice
>>
>>  endif
>> --
>> 1.8.0.3
>>
>>
>> _______________________________________________
>> barebox mailing list
>> barebox@lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/barebox

Best regards
--
Fabio Porcedda

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

^ permalink raw reply	[flat|nested] 3+ messages in thread

end of thread, other threads:[~2013-01-21 12:20 UTC | newest]

Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2013-01-18 16:14 [PATCH] ARM: at91: Add Telit EVK-PRO3 board support Fabio Porcedda
2013-01-19  7:06 ` Jean-Christophe PLAGNIOL-VILLARD
2013-01-21 12:20   ` Fabio Porcedda

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox