mail archive of the barebox mailing list
 help / color / mirror / Atom feed
From: Alexander Aring <alex.aring@gmail.com>
To: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: barebox@lists.infradead.org
Subject: Re: [PATCH 2/3] mxs_spi: initial commit
Date: Mon, 4 Feb 2013 19:15:24 +0100	[thread overview]
Message-ID: <20130204181519.GB27648@x61s.8.8.8.8> (raw)
In-Reply-To: <20130204175742.GA27648@x61s.8.8.8.8>

Hi,

found little thing.

On Mon, Feb 04, 2013 at 06:57:42PM +0100, Alexander Aring wrote:
> Hi Michael,
> 
> On Mon, Feb 04, 2013 at 06:26:20PM +0100, Michael Grzeschik wrote:
> > Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
> > ---
> >  arch/arm/mach-mxs/include/mach/ssp.h |    2 +
> >  drivers/spi/Kconfig                  |    5 +
> >  drivers/spi/Makefile                 |    1 +
> >  drivers/spi/mxs_spi.c                |  306 ++++++++++++++++++++++++++++++++++
> >  4 files changed, 314 insertions(+)
> >  create mode 100644 drivers/spi/mxs_spi.c
> > 
> > diff --git a/arch/arm/mach-mxs/include/mach/ssp.h b/arch/arm/mach-mxs/include/mach/ssp.h
> > index f91770f..067cf12 100644
> > --- a/arch/arm/mach-mxs/include/mach/ssp.h
> > +++ b/arch/arm/mach-mxs/include/mach/ssp.h
> > @@ -23,6 +23,7 @@
> >  #define SSP_CTRL0_BUS_WIDTH(x)		(((x) & 0x3) << 22)
> >  #define SSP_CTRL0_WAIT_FOR_IRQ		(1 << 21)
> >  #define SSP_CTRL0_WAIT_FOR_CMD		(1 << 20)
> > +#define SSP_CTRL0_SSP_ASSERT_OUT(x)	(((x) & 0x3) << 20)
> >  #define SSP_CTRL0_LONG_RESP		(1 << 19)
> >  #define SSP_CTRL0_GET_RESP		(1 << 17)
> >  #define SSP_CTRL0_ENABLE		(1 << 16)
> > @@ -51,6 +52,7 @@
> >  /* bit definition for register HW_SSP_CTRL1 */
> >  #define SSP_CTRL1_POLARITY		(1 << 9)
> >  #define SSP_CTRL1_PHASE			(1 << 10)
> > +#define SSP_CTRL1_DMA_ENABLE		(1 << 13)
> >  #define SSP_CTRL1_WORD_LENGTH(x)	(((x) & 0xf) << 4)
> >  #define SSP_CTRL1_SSP_MODE(x)		((x) & 0xf)
> >  
> > diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
> > index 10b8fea..218c2ff 100644
> > --- a/drivers/spi/Kconfig
> > +++ b/drivers/spi/Kconfig
> > @@ -33,6 +33,11 @@ config DRIVER_SPI_IMX_2_3
> >  	depends on ARCH_IMX51 || ARCH_IMX53 || ARCH_IMX6
> >  	default y
> >  
> > +config DRIVER_SPI_MXS
> > +	bool "i.MX (23,28) SPI Master driver"
> > +	depends on ARCH_MXS

Can we use ARCH23 || ARCH_28 here instead of ARCH_MXS?
I don't know if these two are inside of ARCH_MXS.

Regards Alex

> > +	depends on SPI
> > +
> >  config DRIVER_SPI_OMAP3
> >  	bool "OMAP3 McSPI Master driver"
> >  	depends on ARCH_OMAP3
> > diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
> > index b53061e..642b7ec 100644
> > --- a/drivers/spi/Makefile
> > +++ b/drivers/spi/Makefile
> > @@ -1,5 +1,6 @@
> >  obj-$(CONFIG_SPI) += spi.o
> >  obj-$(CONFIG_DRIVER_SPI_IMX) += imx_spi.o
> > +obj-$(CONFIG_DRIVER_SPI_MXS) += mxs_spi.o
> >  obj-$(CONFIG_DRIVER_SPI_ALTERA) += altera_spi.o
> >  obj-$(CONFIG_DRIVER_SPI_ATMEL) += atmel_spi.o
> >  obj-$(CONFIG_DRIVER_SPI_OMAP3) += omap3_spi.o
> > diff --git a/drivers/spi/mxs_spi.c b/drivers/spi/mxs_spi.c
> > new file mode 100644
> > index 0000000..6fb7f9c
> > --- /dev/null
> > +++ b/drivers/spi/mxs_spi.c
> > @@ -0,0 +1,306 @@
> > +/*
> > + * Freescale i.MX28 SPI driver
> > + *
> > + * Copyright (C) 2013 Michael Grzeschik <mgr@pengutronix.de>
> > + *
> > + * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
> > + * on behalf of DENX Software Engineering GmbH
> > + *
> > + * This program is free software; you can redistribute it and/or
> > + * modify it under the terms of the GNU General Public License as
> > + * published by the Free Software Foundation; either version 2 of
> > + * the License, or (at your option) any later version.
> > + *
> > + */
> > +
> > +#include <common.h>
> > +#include <init.h>
> > +#include <malloc.h>
> > +#include <spi/spi.h>
> > +#include <clock.h>
> > +#include <errno.h>
> > +#include <io.h>
> > +#include <linux/clk.h>
> > +#include <asm/mmu.h>
> > +#include <mach/generic.h>
> > +#include <mach/imx-regs.h>
> > +#include <mach/mxs.h>
> > +#include <mach/clock.h>
> > +#include <mach/ssp.h>
> > +
> > +#define	MXS_SPI_MAX_TIMEOUT		(10 * MSECOND)
> > +
> > +#define	SPI_XFER_BEGIN	0x01 /* Assert CS before transfer */
> > +#define	SPI_XFER_END	0x02 /* Deassert CS after transfer */
> > +
> > +struct mxs_spi {
> > +	struct spi_master	master;
> > +	uint32_t		max_khz;
> > +	uint32_t		mode;
> > +	struct clk		*clk;
> > +	void __iomem		*regs;
> > +};
> > +
> > +static inline struct mxs_spi *to_mxs(struct spi_master *master)
> > +{
> > +	return container_of(master, struct mxs_spi, master);
> > +}
> > +
> > +/*
> > + * Set SSP/MMC bus frequency, in kHz
> > + */
> > +static void imx_set_ssp_busclock(struct spi_master *master, uint32_t freq)
> > +{
> > +	struct mxs_spi *mxs = to_mxs(master);
> > +	const uint32_t sspclk = imx_get_sspclk(master->bus_num);
> > +	uint32_t val;
> > +	uint32_t divide, rate, tgtclk;
> > +
> > +	/*
> > +	 * SSP bit rate = SSPCLK / (CLOCK_DIVIDE * (1 + CLOCK_RATE)),
> > +	 * CLOCK_DIVIDE has to be an even value from 2 to 254, and
> > +	 * CLOCK_RATE could be any integer from 0 to 255.
> > +	 */
> > +	for (divide = 2; divide < 254; divide += 2) {
> > +		rate = sspclk / freq / divide;
> > +		if (rate <= 256)
> > +			break;
> > +	}
> > +
> > +	tgtclk = sspclk / divide / rate;
> > +	while (tgtclk > freq) {
> > +		rate++;
> > +		tgtclk = sspclk / divide / rate;
> > +	}
> > +	if (rate > 256)
> > +		rate = 256;
> > +
> > +	/* Always set timeout the maximum */
> > +	val = SSP_TIMING_TIMEOUT_MASK |
> > +		SSP_TIMING_CLOCK_DIVIDE(divide) |
> > +		SSP_TIMING_CLOCK_RATE(rate - 1);
> > +	writel(val, mxs->regs + HW_SSP_TIMING);
> > +
> > +	debug("SPI%d: Set freq rate to %d KHz (requested %d KHz)\n",
> > +		bus, tgtclk, freq);
> > +}
> > +
> > +static int mxs_spi_setup(struct spi_device *spi)
> > +{
> > +	struct spi_master *master = spi->master;
> > +	struct mxs_spi *mxs = to_mxs(master);
> > +	uint32_t val = 0;
> > +
> > +	/* MXS SPI: 4 ports and 3 chip selects maximum */
> > +	if (master->bus_num > 3 || spi->chip_select > 2) {
> > +		printf("mxs_spi: invalid bus %d / chip select %d\n",
> > +			 master->bus_num, spi->chip_select);
> > +		return -EINVAL;
> > +	}
> > +
> > +	mxs_reset_block(mxs->regs + HW_SSP_CTRL0, 0);
> > +
> > +	val |= SSP_CTRL0_SSP_ASSERT_OUT(spi->chip_select);
> > +	val |= SSP_CTRL0_BUS_WIDTH(0);
> > +	writel(val, mxs->regs + HW_SSP_CTRL0 + BIT_SET);
> > +
> > +	val = SSP_CTRL1_SSP_MODE(0) | SSP_CTRL1_WORD_LENGTH(7);
> > +	val |= (mxs->mode & SPI_CPOL) ? SSP_CTRL1_POLARITY : 0;
> > +	val |= (mxs->mode & SPI_CPHA) ? SSP_CTRL1_PHASE : 0;
> > +	writel(val, mxs->regs + HW_SSP_CTRL1);
> > +
> > +	writel(0x0, mxs->regs + HW_SSP_CMD0);
> > +	writel(0x0, mxs->regs + HW_SSP_CMD1);
> > +
> > +	imx_set_ssp_busclock(master, spi->max_speed_hz);
> > +
> > +	return 0;
> > +}
> > +
> > +static void mxs_spi_start_xfer(struct mxs_spi *mxs)
> > +{
> > +	writel(SSP_CTRL0_LOCK_CS, mxs->regs + HW_SSP_CTRL0 + BIT_SET);
> > +	writel(SSP_CTRL0_IGNORE_CRC, mxs->regs + HW_SSP_CTRL0 + BIT_CLR);
> > +}
> > +
> > +static void mxs_spi_end_xfer(struct mxs_spi *mxs)
> > +{
> > +	writel(SSP_CTRL0_LOCK_CS, mxs->regs + HW_SSP_CTRL0 + BIT_CLR);
> > +	writel(SSP_CTRL0_IGNORE_CRC, mxs->regs + HW_SSP_CTRL0 + BIT_SET);
> > +}
> > +
> > +static uint32_t mxs_spi_cs_to_reg(unsigned cs)
> > +{
> > +	uint32_t select = 0;
> > +
> > +	if (cs & 1)
> > +		select |= SSP_CTRL0_WAIT_FOR_CMD;
> > +	if (cs & 2)
> > +		select |= SSP_CTRL0_WAIT_FOR_IRQ;
> > +
> > +	return select;
> > +}
> > +
> > +static void mxs_spi_set_cs(struct spi_device *spi)
> > +{
> > +	const uint32_t mask = SSP_CTRL0_WAIT_FOR_CMD | SSP_CTRL0_WAIT_FOR_IRQ;
> > +	uint32_t select;
> > +	struct mxs_spi *mxs = to_mxs(spi->master);
> > +
> > +	writel(mask, mxs->regs + HW_SSP_CTRL0 + BIT_CLR);
> > +	select = mxs_spi_cs_to_reg(spi->chip_select);
> > +	writel(select, mxs->regs + HW_SSP_CTRL0 + BIT_SET);
> > +}
> > +
> > +static int mxs_spi_xfer_pio(struct spi_device *spi,
> > +			char *data, int length, int write, unsigned long flags)
> > +{
> > +	struct mxs_spi *mxs = to_mxs(spi->master);
> > +
> > +	if (flags & SPI_XFER_BEGIN)
> > +		mxs_spi_start_xfer(mxs);
> > +
> > +	mxs_spi_set_cs(spi);
> > +
> > +	while (length--) {
> > +		if ((flags & SPI_XFER_END) && !length)
> > +			mxs_spi_end_xfer(mxs);
> > +
> > +		/* We transfer 1 byte */
> > +		writel(1, mxs->regs + HW_SSP_XFER_COUNT);
> > +
> > +		if (write)
> > +			writel(SSP_CTRL0_READ, mxs->regs + HW_SSP_CTRL0 + BIT_CLR);
> > +		else
> > +			writel(SSP_CTRL0_READ, mxs->regs + HW_SSP_CTRL0 + BIT_SET);
> > +
> > +		writel(SSP_CTRL0_RUN, mxs->regs + HW_SSP_CTRL0 + BIT_SET);
> > +
> > +		if (wait_on_timeout(MXS_SPI_MAX_TIMEOUT,
> > +				(readl(mxs->regs + HW_SSP_CTRL0) & SSP_CTRL0_RUN) == SSP_CTRL0_RUN)) {
> > +			printf("MXS SPI: Timeout waiting for start\n");
> > +			return -ETIMEDOUT;
> > +		}
> > +
> > +		if (write)
> > +			writel(*data++, mxs->regs + HW_SSP_DATA);
> > +
> > +		writel(SSP_CTRL0_DATA_XFER, mxs->regs + HW_SSP_CTRL0 + BIT_SET);
> > +
> > +		if (!write) {
> > +			if (wait_on_timeout(MXS_SPI_MAX_TIMEOUT,
> > +				!(readl(mxs->regs + HW_SSP_STATUS) & SSP_STATUS_FIFO_EMPTY))) {
> > +				printf("MXS SPI: Timeout waiting for data\n");
> > +				return -ETIMEDOUT;
> > +			}
> > +
> > +			*data++ = readl(mxs->regs + HW_SSP_DATA) & 0xff;
> > +		}
> > +
> > +		if (wait_on_timeout(MXS_SPI_MAX_TIMEOUT,
> > +			!(readl(mxs->regs + HW_SSP_CTRL0) & SSP_CTRL0_RUN))) {
> > +			printf("MXS SPI: Timeout waiting for finish\n");
> > +			return -ETIMEDOUT;
> > +		}
> > +	}
> > +
> > +	return 0;
> > +}
> > +
> > +static int mxs_spi_transfer(struct spi_device *spi, struct spi_message *mesg)
> > +{
> > +	struct mxs_spi *mxs = to_mxs(spi->master);
> > +	struct spi_transfer *t = NULL;
> > +	char dummy;
> > +	unsigned long flags = 0;
> > +	int write = 0;
> > +	char *data = NULL;
> > +	int ret;
> > +	mesg->actual_length = 0;
> > +
> > +	list_for_each_entry(t, &mesg->transfers, transfer_list) {
> > +
> 
> Maybe we should remove this whitespace newline.
> 
> > +		flags = 0;
> > +
> > +		if (t->tx_buf) {
> > +			data = (char *) t->tx_buf;
> > +			write = 1;
> > +		} else if (t->rx_buf) {
> > +			data = (char *) t->rx_buf;
> > +			write = 0;
> > +		}
> > +
> > +		if (&t->transfer_list == mesg->transfers.next)
> > +			flags |= SPI_XFER_BEGIN;
> > +
> > +		if (&t->transfer_list == mesg->transfers.prev)
> > +			flags |= SPI_XFER_END;
> > +
> > +		if ((t->rx_buf && t->tx_buf)) {
> > +			printf("Cannot send and receive simultaneously \n");
> > +			break;
> 
> Maybe we should return -EIO or something here with variable ret.
> 
> > +		}
> > +
> > +		if ((!t->rx_buf && !t->tx_buf)) {
> > +			printf("No Data\n");
> > +			break;
> 
> Same here.
> 
> > +		}
> > +
> > +		if (t->len == 0) {
> > +			if (flags == SPI_XFER_END) {
> > +				t->len = 1;
> > +				t->rx_buf = (void *) &dummy;
> > +			} else {
> > +				return 0;
> > +			}
> > +		}
> > +
> > +		writel(SSP_CTRL1_DMA_ENABLE, mxs->regs + HW_SSP_CTRL1 + BIT_CLR);
> > +		ret = mxs_spi_xfer_pio(spi, data, t->len, write, flags);
> 
> ret is never read in this function after that.
> 
> Regards Alex
> 
> > +		mesg->actual_length += t->len;
> > +	}
> > +
> > +	return 0;
> > +}
> > +
> > +static int mxs_spi_probe(struct device_d *dev)
> > +{
> > +	struct spi_master *master;
> > +	struct mxs_spi *mxs;
> > +
> > +	mxs = xzalloc(sizeof(*mxs));
> > +	if (!mxs)
> > +		return -ENOMEM;
> > +
> > +	master = &mxs->master;
> > +	master->dev = dev;
> > +
> > +	master->bus_num = dev->id;
> > +	master->setup = mxs_spi_setup;
> > +	master->transfer = mxs_spi_transfer;
> > +	master->num_chipselect = 3;
> > +	mxs->mode = SPI_CPOL | SPI_CPHA;
> > +
> > +	mxs->regs = dev_request_mem_region(dev, 0);
> > +
> > +	spi_register_master(master);
> > +
> > +	return 0;
> > +}
> > +
> > +static struct driver_d mxs_spi_driver = {
> > +	.name  = "mxs_spi",
> > +	.probe = mxs_spi_probe,
> > +};
> > +
> > +static int __init mxs_spi_init(void)
> > +{
> > +	platform_driver_register(&mxs_spi_driver);
> > +	return 0;
> > +}
> > +
> > +device_initcall(mxs_spi_init);
> > +
> > +MODULE_AUTHOR("Denx Software Engeneering and Michael Grzeschik");
> > +MODULE_DESCRIPTION("MXS SPI driver");
> > +MODULE_LICENSE("GPL");
> > -- 
> > 1.7.10.4
> > 
> > 
> > _______________________________________________
> > barebox mailing list
> > barebox@lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/barebox

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

  reply	other threads:[~2013-02-04 18:15 UTC|newest]

Thread overview: 13+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2013-02-04 17:26 [PATCH 0/3] Add mxs spi driver and mx28evk as its first user Michael Grzeschik
2013-02-04 17:26 ` [PATCH 1/3] mxs: ssp move to common register layout Michael Grzeschik
2013-02-05  9:10   ` Sascha Hauer
2013-02-04 17:26 ` [PATCH 2/3] mxs_spi: initial commit Michael Grzeschik
2013-02-04 17:57   ` Alexander Aring
2013-02-04 18:15     ` Alexander Aring [this message]
2013-02-04 18:18       ` Alexander Aring
2013-02-05  9:22   ` Sascha Hauer
2013-02-04 17:26 ` [PATCH 3/3] mx28evk: add m25p80 flash via ssp2 Michael Grzeschik
2013-02-05  9:24   ` Sascha Hauer
  -- strict thread matches above, loose matches on Subject: below --
2013-02-04 16:26 [PATCH 0/3] Add mxs spi driver and mx28evk as its first user Michael Grzeschik
2013-02-04 16:26 ` [PATCH 2/3] mxs_spi: initial commit Michael Grzeschik
2013-02-04 16:26 ` Michael Grzeschik
2013-02-04 17:10   ` Michael Grzeschik

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20130204181519.GB27648@x61s.8.8.8.8 \
    --to=alex.aring@gmail.com \
    --cc=barebox@lists.infradead.org \
    --cc=m.grzeschik@pengutronix.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox