mail archive of the barebox mailing list
 help / color / mirror / Atom feed
From: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
To: Uladzimir Bely <u.bely@sam-solutions.com>
Cc: barebox@lists.infradead.org
Subject: Re: [PATCH] ARM: OMAP5 processors support
Date: Thu, 25 Apr 2013 13:05:21 +0200	[thread overview]
Message-ID: <20130425110521.GG13393@game.jcrosoft.org> (raw)
In-Reply-To: <1366880959-25765-1-git-send-email-u.bely@sam-solutions.com>

On 12:09 Thu 25 Apr     , Uladzimir Bely wrote:
> Since commit
> 	8bafdc1 ARM i.MX28: make chip reset via reset pin work again
> 
> Patch adds basic OMAP5 support to barebox.
> 
> Tested on SD card with 2 partitions: vfat (MLO, barebox.bin, zImage)
> and ext3 (rootfs). Barebox successfully starts kernel
> from commandline with "bootm /boot/zImage" command.
> 
> Building MLO: make omap5_sevm_xload_defconfig; make.
> Building barebox.bin: make omap5_sevm_defconfig; make.
> 
> It's an optimized and cleaned up version of previous patch.
> 
> Signed-off-by: Uladzimir Bely <u.bely@sam-solutions.com>
> ---
>  arch/arm/Makefile                               |   1 +
>  arch/arm/boards/omap5_sevm/Makefile             |   2 +
>  arch/arm/boards/omap5_sevm/board.c              |  57 +++
>  arch/arm/boards/omap5_sevm/config.h             |   1 +
>  arch/arm/boards/omap5_sevm/env/config           |  11 +
>  arch/arm/boards/omap5_sevm/lowlevel.c           | 137 +++++++
>  arch/arm/boards/omap5_sevm/mux.c                | 284 +++++++++++++
>  arch/arm/configs/omap5_sevm_defconfig           |  68 ++++
>  arch/arm/configs/omap5_sevm_xload_defconfig     |  44 ++
>  arch/arm/mach-omap/Kconfig                      |  16 +
>  arch/arm/mach-omap/Makefile                     |   2 +
>  arch/arm/mach-omap/gpmc.c                       |   3 +
>  arch/arm/mach-omap/include/mach/debug_ll.h      |   5 +
>  arch/arm/mach-omap/include/mach/generic.h       |   7 +
>  arch/arm/mach-omap/include/mach/gpmc_nand.h     |   1 +
>  arch/arm/mach-omap/include/mach/omap5-clock.h   | 425 ++++++++++++++++++++
>  arch/arm/mach-omap/include/mach/omap5-devices.h |  21 +
>  arch/arm/mach-omap/include/mach/omap5-mux.h     | 321 +++++++++++++++
>  arch/arm/mach-omap/include/mach/omap5-silicon.h | 235 +++++++++++
>  arch/arm/mach-omap/omap5_clock.c                | 385 ++++++++++++++++++
>  arch/arm/mach-omap/omap5_generic.c              | 509 ++++++++++++++++++++++++
>  arch/arm/mach-omap/omap_generic.c               |   2 +
>  arch/arm/mach-omap/s32k_clksource.c             |   7 +
>  drivers/mci/Kconfig                             |   2 +-
>  drivers/mci/omap_hsmmc.c                        |   7 +
>  25 files changed, 2552 insertions(+), 1 deletion(-)
>  create mode 100644 arch/arm/boards/omap5_sevm/Makefile
>  create mode 100644 arch/arm/boards/omap5_sevm/board.c
>  create mode 100644 arch/arm/boards/omap5_sevm/config.h
>  create mode 100644 arch/arm/boards/omap5_sevm/env/config
>  create mode 100644 arch/arm/boards/omap5_sevm/lowlevel.c
>  create mode 100644 arch/arm/boards/omap5_sevm/mux.c
>  create mode 100644 arch/arm/configs/omap5_sevm_defconfig
>  create mode 100644 arch/arm/configs/omap5_sevm_xload_defconfig
>  create mode 100644 arch/arm/mach-omap/include/mach/omap5-clock.h
>  create mode 100644 arch/arm/mach-omap/include/mach/omap5-devices.h
>  create mode 100644 arch/arm/mach-omap/include/mach/omap5-mux.h
>  create mode 100644 arch/arm/mach-omap/include/mach/omap5-silicon.h
>  create mode 100644 arch/arm/mach-omap/omap5_clock.c
>  create mode 100644 arch/arm/mach-omap/omap5_generic.c
> 
> diff --git a/arch/arm/Makefile b/arch/arm/Makefile
> index d506b12..fb459b5 100644
> --- a/arch/arm/Makefile
> +++ b/arch/arm/Makefile
> @@ -162,6 +162,7 @@ board-$(CONFIG_MACH_SABRELITE)			:= freescale-mx6-sabrelite
>  board-$(CONFIG_MACH_TX53)			:= karo-tx53
>  board-$(CONFIG_MACH_GUF_VINCELL)		:= guf-vincell
>  board-$(CONFIG_MACH_EFIKA_MX_SMARTBOOK)		:= efika-mx-smartbook
> +board-$(CONFIG_MACH_OMAP5_SEVM)			:= omap5_sevm
>  board-$(CONFIG_MACH_SABRESD)			:= freescale-mx6-sabresd
>  board-$(CONFIG_MACH_REALQ7)			:= dmo-mx6-realq7
>  board-$(CONFIG_MACH_ZEDBOARD)			:= avnet-zedboard
> diff --git a/arch/arm/boards/omap5_sevm/Makefile b/arch/arm/boards/omap5_sevm/Makefile
> new file mode 100644
> index 0000000..5d4eb10
> --- /dev/null
> +++ b/arch/arm/boards/omap5_sevm/Makefile
> @@ -0,0 +1,2 @@
> +obj-y += board.o
> +lwl-y += lowlevel.o mux.o
> diff --git a/arch/arm/boards/omap5_sevm/board.c b/arch/arm/boards/omap5_sevm/board.c
> new file mode 100644
> index 0000000..5700d6a
> --- /dev/null
> +++ b/arch/arm/boards/omap5_sevm/board.c
> @@ -0,0 +1,57 @@
> +/*
> + * omap5_sevm - OMAP5-based board initalization code
> + *
> + * (C) Copyright 2013
> + * Sam Solutions, <sam-solutions.com>
> + *
> + * Authors:
> + *	Uladzimir Bely <u.bely@sam-solutions.com>
> + *	Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
> + */
> +
> +#include <common.h>
> +#include <console.h>
> +#include <init.h>
> +#include <driver.h>
> +#include <io.h>
> +#include <ns16550.h>
> +#include <asm/armlinux.h>
> +#include <generated/mach-types.h>
> +#include <mach/omap5-silicon.h>
> +#include <mach/omap5-devices.h>
> +#include <mach/sdrc.h>
> +#include <mach/sys_info.h>
> +#include <mach/syslib.h>
> +#include <mach/control.h>
> +#include <linux/err.h>
> +#include <sizes.h>
> +#include <asm/mmu.h>
> +#include <mach/gpio.h>
> +#include <i2c/i2c.h>
> +
> +static int omap5_sevm_console_init(void)
> +{
> +	omap54xx_add_uart3();
> +
> +	return 0;
> +}
> +console_initcall(omap5_sevm_console_init);
> +
> +static int omap5_sevm_mem_init(void)
> +{
> +	omap_add_ram0(SZ_512M);
can we detect it?
> +
> +	return 0;
> +}
> +mem_initcall(omap5_sevm_mem_init);
> +
> +static int omap5_sevm_devices_init(void)
> +{
> +	omap54xx_add_mmc1(NULL);
> +
> +	armlinux_set_bootparams((void *)0x80000100);
> +	armlinux_set_architecture(MACH_TYPE_OMAP5_SEVM);
IIRC the omap5 is DT only
> +
> +	return 0;
> +}
> +device_initcall(omap5_sevm_devices_init);
> diff --git a/arch/arm/boards/omap5_sevm/config.h b/arch/arm/boards/omap5_sevm/config.h
> new file mode 100644
> index 0000000..da84fa5
> --- /dev/null
> +++ b/arch/arm/boards/omap5_sevm/config.h
> @@ -0,0 +1 @@
> +/* nothing */
> diff --git a/arch/arm/boards/omap5_sevm/env/config b/arch/arm/boards/omap5_sevm/env/config
> new file mode 100644
> index 0000000..9752957
> --- /dev/null
> +++ b/arch/arm/boards/omap5_sevm/env/config
> @@ -0,0 +1,11 @@
> +#!/bin/sh
> +
> +machine=omap5
> +
> +autoboot_timeout=2
> +
> +bootargs="console=ttyO2,115200"
> +
> +kernel_loc=disk
> +
> +PS1="\e[1;32mbarebox@\e[1;31m\h:\w\e[0m "
please switch to defaultenv-2
> diff --git a/arch/arm/boards/omap5_sevm/lowlevel.c b/arch/arm/boards/omap5_sevm/lowlevel.c
> new file mode 100644
> index 0000000..b4479b2
> --- /dev/null
> +++ b/arch/arm/boards/omap5_sevm/lowlevel.c
> @@ -0,0 +1,137 @@
> +/*
> + * omap5_sevm - OMAP5-based board low-level initalization code
> + *
> + * (C) Copyright 2013
> + * Sam Solutions, <sam-solutions.com>
> + *
> + * Authors:
> + *	Uladzimir Bely <u.bely@sam-solutions.com>
> + *	Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
> + *
> + * Derived from OMAP5 work in U-Boot project
> + */
> +
> +#include <common.h>
> +#include <io.h>
> +#include <mach/omap5-mux.h>
> +#include <mach/omap5-silicon.h>
> +#include <mach/omap5-clock.h>
> +#include <mach/syslib.h>
> +#include <asm/barebox-arm.h>
> +#include <asm/barebox-arm-head.h>
> +
> +void set_muxconf_regs(void);
> +
> +static const struct omap5_ddr_regs ddr_regs_elpida_532_mhz_2cs = {
> +	.sdram_config_init		= 0x80800EBA,	/* 00 */
> +	.sdram_config			= 0x808022BA,	/* 04 */
> +	.ref_ctrl			= 0x0000081A,	/* 08 */
> +	.sdram_tim1			= 0x772F6873,	/* 0c */
> +	.sdram_tim2			= 0x304a129a,	/* 01 */
> +	.sdram_tim3			= 0x02f7e45f,	/* 14 */
> +	.read_idle_ctrl			= 0x00050000,	/* 18 */
> +	.zq_config			= 0x000b3215,	/* 1c */
> +	.temp_alert_config		= 0x08000a05,	/* 20 */
> +	.emif_ddr_phy_ctlr_1_init	= 0x0E28420d,	/* 24 */
> +	.emif_ddr_phy_ctlr_1		= 0x0E28420d,	/* 28 */
> +	.emif_ddr_ext_phy_ctrl_1_init	= 0x04020080,	/* 2c */
> +	.emif_ddr_ext_phy_ctrl_1	= 0x04020080,	/* 30 */
> +	.emif_ddr_ext_phy_ctrl_2_init	= 0x28C518A3,	/* 34 */
> +	.emif_ddr_ext_phy_ctrl_2	= 0x28C518A3,	/* 38 */
> +	.emif_ddr_ext_phy_ctrl_3_init	= 0x518A3146,	/* 3c */
> +	.emif_ddr_ext_phy_ctrl_3	= 0x518A3146,	/* 40 */
> +	.emif_ddr_ext_phy_ctrl_4_init	= 0x0014628C,	/* 44 */
> +	.emif_ddr_ext_phy_ctrl_4	= 0x0014628C,	/* 48 */
> +	.emif_ddr_ext_phy_ctrl_5_init	= 0x04010040,	/* 4c */
> +	.emif_ddr_ext_phy_ctrl_5	= 0x04010040,	/* 50 */
> +	.emif_ddr_ext_phy_ctrl_6_init	= 0x01004010,	/* 54 */
> +	.emif_ddr_ext_phy_ctrl_6	= 0x01004010,	/* 58 */
> +	.emif_ddr_ext_phy_ctrl_7_init	= 0x00001004,	/* 5c */
> +	.emif_ddr_ext_phy_ctrl_7	= 0x00001004,	/* 60 */
> +	.emif_ddr_ext_phy_ctrl_8_init	= 0x04010040,	/* 64 */
> +	.emif_ddr_ext_phy_ctrl_8	= 0x04010040,	/* 68 */
> +	.emif_ddr_ext_phy_ctrl_9_init	= 0x01004010,	/* 6c */
> +	.emif_ddr_ext_phy_ctrl_9	= 0x01004010,	/* 70 */
> +	.emif_ddr_ext_phy_ctrl_10_init	= 0x00001004,	/* 74 */
> +	.emif_ddr_ext_phy_ctrl_10	= 0x00001004,	/* 78 */
> +	.emif_ddr_ext_phy_ctrl_11_init	= 0x00000000,	/* 7c */
> +	.emif_ddr_ext_phy_ctrl_11	= 0x00000000,	/* 80 */
> +	.emif_ddr_ext_phy_ctrl_12_init	= 0x00000000,	/* 84 */
> +	.emif_ddr_ext_phy_ctrl_12	= 0x00000000,	/* 88 */
> +	.emif_ddr_ext_phy_ctrl_13_init	= 0x00000000,	/* 8c */
> +	.emif_ddr_ext_phy_ctrl_13	= 0x00000000,	/* 90 */
> +	.emif_ddr_ext_phy_ctrl_14_init	= 0x80080080,	/* 94 */
> +	.emif_ddr_ext_phy_ctrl_14	= 0x80080080,	/* 98 */
> +	.emif_ddr_ext_phy_ctrl_15_init	= 0x00800800,	/* 9c */
> +	.emif_ddr_ext_phy_ctrl_15	= 0x00800800,	/* a0 */
> +	.emif_ddr_ext_phy_ctrl_16_init	= 0x08102040,	/* a4 */
> +	.emif_ddr_ext_phy_ctrl_16	= 0x08102040,	/* a8 */
> +	.emif_ddr_ext_phy_ctrl_17_init	= 0x00000001,	/* ac */
> +	.emif_ddr_ext_phy_ctrl_17	= 0x00000001,	/* b0 */
> +	.emif_ddr_ext_phy_ctrl_18_init	= 0x540A8150,	/* b4 */
> +	.emif_ddr_ext_phy_ctrl_18	= 0x540A8150,	/* b8 */
> +	.emif_ddr_ext_phy_ctrl_19_init	= 0xA81502A0,	/* bc */
> +	.emif_ddr_ext_phy_ctrl_19	= 0xA81502a0,	/* c0 */
> +	.emif_ddr_ext_phy_ctrl_20_init	= 0x002A0540,	/* c4 */
> +	.emif_ddr_ext_phy_ctrl_20	= 0x002A0540,	/* c8 */
> +	.emif_ddr_ext_phy_ctrl_21_init	= 0x00000000,	/* cc */
> +	.emif_ddr_ext_phy_ctrl_21	= 0x00000000,	/* d0 */
> +	.emif_ddr_ext_phy_ctrl_22_init	= 0x00000000,	/* d4 */
> +	.emif_ddr_ext_phy_ctrl_22	= 0x00000000,	/* d8 */
> +	.emif_ddr_ext_phy_ctrl_23_init	= 0x00000000,	/* dc */
> +	.emif_ddr_ext_phy_ctrl_23	= 0x00000000,	/* e0 */
> +	.emif_ddr_ext_phy_ctrl_24_init	= 0x00000077,	/* e4 */
> +	.emif_ddr_ext_phy_ctrl_24	= 0x00000077,	/* e8 */
> +	.emif_rd_wr_lvl_rmp_win		= 0x0,		/* ec */
> +	.emif_rd_wr_lvl_rmp_ctl		= 0x0,		/* f0 */
> +	.emif_rd_wr_lvl_ctl		= 0x20000000,	/* f4 */
> +	.emif_rd_wr_exec_thresh		= 0x00000305	/* f8 */
> +};
> +
> +static void noinline omap5_sevm_init_lowlevel(void)
> +{
> +	struct dpll_param core = OMAP5_CORE_DPLL_PARAM_19M2_NOM;
> +	struct dpll_param mpu = OMAP5_MPU_DPLL_PARAM_19M2_NOM;
> +	struct dpll_param iva = OMAP5_IVA_DPLL_PARAM_19M2_NOM;
> +	struct dpll_param per = OMAP5_PER_DPLL_PARAM_19M2_NOM;
> +	struct dpll_param abe = OMAP5_ABE_DPLL_PARAM;
> +	struct dpll_param usb = OMAP5_USB_DPLL_PARAM_19M2;
> +
> +	set_muxconf_regs();
> +
> +	omap5_ddr_init(&ddr_regs_elpida_532_mhz_2cs, &core);
> +
> +	omap5_scale_vcores();
> +
> +	writel(CM_CLKSEL_SYS_19M2, CM_CLKSEL_SYS);
> +
> +	/* Configure all DPLL's at 100% OPP */
> +	omap5_configure_mpu_dpll(&mpu);
> +	omap5_configure_iva_dpll(&iva);
> +	omap5_configure_per_dpll(&per);
> +	omap5_configure_abe_dpll(&abe);
> +	omap5_configure_usb_dpll(&usb);
> +
> +	/* Enable all clocks */
> +	omap5_enable_all_clocks();
> +
> +	sr32(0x4Ae0a31C, 8, 1, 0x1);	/* enable software ioreq */
> +	sr32(0x4Ae0a31C, 1, 2, 0x0);	/* set for sys_clk (19.2MHz) */
> +	sr32(0x4Ae0a31C, 16, 4, 0x0);	/* set divisor to 1 */
> +	sr32(0x4Ae0a110, 0, 1, 0x1);	/* set the clock source to active */
> +	sr32(0x4Ae0a110, 2, 2, 0x3);	/* enable clocks */
> +}
> +
> +void barebox_arm_reset_vector(void)
> +{
> +	arm_cpu_lowlevel_init();
> +
> +	if (get_pc() > 0x80000000)
> +		goto out;
> +
> +	arm_setup_stack(0x4030d000);
> +
> +	omap5_sevm_init_lowlevel();
> +out:
> +	barebox_arm_entry(0x80000000, SZ_512M, 0);
really hardcoded?
> +}
> diff --git a/arch/arm/boards/omap5_sevm/mux.c b/arch/arm/boards/omap5_sevm/mux.c
> new file mode 100644
> index 0000000..4f6b5cd
> --- /dev/null
> +++ b/arch/arm/boards/omap5_sevm/mux.c
> @@ -0,0 +1,284 @@
> +/*
> + * (C) Copyright 2013
> + * Sam Solutions, <sam-solutions.com>
> + *
> + * Authors:
> + *	Uladzimir Bely <u.bely@sam-solutions.com>
> + *	Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
> + *
> + * Derived from OMAP5 work in U-Boot project by
> + * Aneesh V <aneesh@ti.com>
> + * Sricharan R <r.sricharan@ti.com>
> + * (Copyright 2010, Texas Instruments, <www.ti.com>)
> + */
> +
> +#include <common.h>
> +#include <init.h>
> +#include <io.h>
> +#include <mach/omap5-silicon.h>
> +#include <mach/omap5-mux.h>
> +#include <mach/omap5-clock.h>
> +
> +static const struct pad_conf_entry core_padconf_array[] = {
> +	{EMMC_CLK, (PTU | IEN | M0)},
> +	{EMMC_CMD, (PTU | IEN | M0)},
> +	{EMMC_DATA0, (PTU | IEN | M0)},
> +	{EMMC_DATA1, (PTU | IEN | M0)},
> +	{EMMC_DATA2, (PTU | IEN | M0)},
> +	{EMMC_DATA3, (PTU | IEN | M0)},
> +	{EMMC_DATA4, (PTU | IEN | M0)},
> +	{EMMC_DATA5, (PTU | IEN | M0)},
> +	{EMMC_DATA6, (PTU | IEN | M0)},
> +	{EMMC_DATA7, (PTU | IEN | M0)},
> +	{C2C_CLKOUT0, (M0)},
> +	{C2C_CLKOUT1, (M0)},
> +	{C2C_CLKIN0,  (IEN | M0)},
> +	{C2C_CLKIN1,  (IEN | M0)},
> +	{C2C_DATAIN0, (IEN | M0)},
> +	{C2C_DATAIN1, (IEN | M0)},
> +	{C2C_DATAIN2, (IEN | M0)},
> +	{C2C_DATAIN3, (IEN | M0)},
> +	{C2C_DATAIN4, (IEN | M0)},
> +	{C2C_DATAIN5, (IEN | M0)},
> +	{C2C_DATAIN6, (IEN | M0)},
> +	{C2C_DATAIN7, (IEN | M0)},
> +	{C2C_DATAOUT0, (M0)},
> +	{C2C_DATAOUT1, (M0)},
> +	{C2C_DATAOUT2, (M0)},
> +	{C2C_DATAOUT3, (M0)},
> +	{C2C_DATAOUT4, (M0)},
> +	{C2C_DATAOUT5, (M0)},
> +	{C2C_DATAOUT6, (M0)},
> +	{C2C_DATAOUT7, (M0)},
> +	{C2C_DATA8, (IEN | M0)},
> +	{C2C_DATA9, (IEN | M0)},
> +	{C2C_DATA10, (IEN | M0)},
> +	{C2C_DATA11, (IEN | M0)},
> +	{C2C_DATA12, (IEN | M0)},
> +	{C2C_DATA13, (IEN | M0)},
> +	{C2C_DATA14, (IEN | M0)},
> +	{C2C_DATA15, (IEN | M0)},
> +	{LLIB_WAKEREQOUT, (PTU | IEN | M6)},
> +	{LLIA_WAKEREQOUT, (M1)},
> +	{HSI1_ACREADY, (PTD | M6)},
> +	{HSI1_CAREADY, (PTD | M6)},
> +	{HSI1_ACWAKE,  (PTD | IEN | M6)},
> +	{HSI1_CAWAKE,  (PTU | IEN | M6)},
> +	{HSI1_ACFLAG,  (PTD | IEN | M6)},
> +	{HSI1_ACDATA,  (PTD | M6)},
> +	{HSI1_CAFLAG,  (M6)},
> +	{HSI1_CADATA,  (M6)},
> +	{UART1_TX, (M0)},
> +	{UART1_CTS, (PTU | IEN | M0)},
> +	{UART1_RX, (PTU | IEN | M0)},
> +	{UART1_RTS, (M0)},
> +	{HSI2_CAREADY, (IEN | M0)},
> +	{HSI2_ACREADY, (M0)},
> +	{HSI2_CAWAKE, (IEN | M0)},
> +	{HSI2_ACWAKE, (M0)},
> +	{HSI2_CAFLAG, (IEN | M0)},
> +	{HSI2_CADATA, (IEN | M0)},
> +	{HSI2_ACFLAG, (M0)},
> +	{HSI2_ACDATA, (M0)},
> +	{UART2_RTS, (IEN | M1)},
> +	{UART2_CTS, (IEN | M1)},
> +	{UART2_RX, (IEN | M1)},
> +	{UART2_TX, (IEN | M1)},
> +	{USBB1_HSIC_STROBE, (PTU | IEN | M0)},
> +	{USBB1_HSIC_DATA, (PTU | IEN | M0)},
> +	{USBB2_HSIC_STROBE, (PTU | IEN | M0)},
> +	{USBB2_HSIC_DATA, (PTU | IEN | M0)},
> +	{TIMER10_PWM_EVT, (IEN | M0)},
> +	{DSIPORTA_TE0, (IEN | M0)},
> +	{DSIPORTA_LANE0X, (IEN | M0)},
> +	{DSIPORTA_LANE0Y, (IEN | M0)},
> +	{DSIPORTA_LANE1X, (IEN | M0)},
> +	{DSIPORTA_LANE1Y, (IEN | M0)},
> +	{DSIPORTA_LANE2X, (IEN | M0)},
> +	{DSIPORTA_LANE2Y, (IEN | M0)},
> +	{DSIPORTA_LANE3X, (IEN | M0)},
> +	{DSIPORTA_LANE3Y, (IEN | M0)},
> +	{DSIPORTA_LANE4X, (IEN | M0)},
> +	{DSIPORTA_LANE4Y, (IEN | M0)},
> +	{DSIPORTC_LANE0X, (IEN | M0)},
> +	{DSIPORTC_LANE0Y, (IEN | M0)},
> +	{DSIPORTC_LANE1X, (IEN | M0)},
> +	{DSIPORTC_LANE1Y, (IEN | M0)},
> +	{DSIPORTC_LANE2X, (IEN | M0)},
> +	{DSIPORTC_LANE2Y, (IEN | M0)},
> +	{DSIPORTC_LANE3X, (IEN | M0)},
> +	{DSIPORTC_LANE3Y, (IEN | M0)},
> +	{DSIPORTC_LANE4X, (IEN | M0)},
> +	{DSIPORTC_LANE4Y, (IEN | M0)},
> +	{DSIPORTC_TE0, (IEN | M0)},
> +	{TIMER9_PWM_EVT, (IEN | M0)},
> +	{I2C4_SCL, (IEN | M0)},
> +	{I2C4_SDA, (IEN | M0)},
> +	{MCSPI2_CLK, (IEN | M0)},
> +	{MCSPI2_SIMO, (IEN | M0)},
> +	{MCSPI2_SOMI, (PTU | IEN | M0)},
> +	{MCSPI2_CS0, (M0)},
> +	{RFBI_DATA15, (M4)},
> +	{RFBI_DATA14, (M4)},
> +	{RFBI_DATA13, (PTU | IEN | M6)},
> +	{RFBI_DATA12, (PTD | M6)},
> +	{RFBI_DATA11, (PTD | M6)},
> +	{RFBI_DATA10, (PTD | M6)},
> +	{RFBI_DATA9, (PTD | M6)},
> +	{RFBI_DATA8, (M4)},
> +	{RFBI_DATA7, (PTD | M6)},
> +	{RFBI_DATA6, (PTD | M6)},
> +	{RFBI_DATA5, (IEN | M6)},
> +	{RFBI_DATA4, (IEN | M6)},
> +	{RFBI_DATA3, (PTD | IEN | M6)},
> +	{RFBI_DATA2, (PTD | M6)},
> +	{RFBI_DATA1, (PTD | M6)},
> +	{RFBI_DATA0, (PTD | M6)},
> +	{RFBI_WE, (PTD | M6)},
> +	{MCSPI2_CS0, (M0)},
> +	{RFBI_A0, (PTD | IEN | M6)},
> +	{RFBI_RE, (M4)},
> +	{RFBI_HSYNC0, (M4)},
> +	{RFBI_TE_VSYNC0, (PTD | M6)},
> +	{GPIO6_182, (M6)},
> +	{GPIO6_183, (PTD | M6)},
> +	{GPIO6_184, (M4)},
> +	{GPIO6_185, (PTD | IEN | M6)},
> +	{GPIO6_186, (PTD | M6)},
> +	{GPIO6_187, (PTU | IEN | M4)},
> +	{HDMI_CEC, (IEN | M0)},
> +	{HDMI_HPD, (PTD | IEN | M0)},
> +	{HDMI_DDC_SCL, (IEN | M0)},
> +	{HDMI_DDC_SDA, (IEN | M0)},
> +	{CSIPORTC_LANE0X, (IEN | M0)},
> +	{CSIPORTC_LANE0Y, (IEN | M0)},
> +	{CSIPORTC_LANE1X, (IEN | M0)},
> +	{CSIPORTC_LANE1Y, (IEN | M0)},
> +	{CSIPORTB_LANE0X, (IEN | M0)},
> +	{CSIPORTB_LANE0Y, (IEN | M0)},
> +	{CSIPORTB_LANE1X, (IEN | M0)},
> +	{CSIPORTB_LANE1Y, (IEN | M0)},
> +	{CSIPORTB_LANE2X, (IEN | M0)},
> +	{CSIPORTB_LANE2Y, (IEN | M0)},
> +	{CSIPORTB_LANE0X, (IEN | M0)},
> +	{CSIPORTB_LANE0Y, (IEN | M0)},
> +	{CSIPORTA_LANE1X, (IEN | M0)},
> +	{CSIPORTA_LANE1Y, (IEN | M0)},
> +	{CSIPORTA_LANE2X, (IEN | M0)},
> +	{CSIPORTA_LANE2Y, (IEN | M0)},
> +	{CSIPORTA_LANE3X, (IEN | M0)},
> +	{CSIPORTA_LANE3Y, (IEN | M0)},
> +	{CSIPORTA_LANE4X, (IEN | M0)},
> +	{CSIPORTA_LANE4Y, (IEN | M0)},
> +	{CAM_SHUTTER, (M0)},
> +	{CAM_STROBE, (M0)},
> +	{CAM_GLOBALRESET, (IEN | M0)},
> +	{TIMER11_PWM_EVT, (PTD | M6)},
> +	{TIMER5_PWM_EVT, (PTD | M6)},
> +	{TIMER6_PWM_EVT, (PTD | M6)},
> +	{TIMER8_PWM_EVT,      (PTU | M6)},
> +	{I2C3_SCL, (IEN | M0)},
> +	{I2C3_SDA, (IEN | M0)},
> +	{GPIO8_233, (IEN | M2)},
> +	{GPIO8_234, (IEN | M3)},
> +	{ABE_CLKS, (IEN | M0)},
> +	{ABEDMIC_DIN1, (IEN | M0)},
> +	{ABEDMIC_DIN2, (IEN | M0)},
> +	{ABEDMIC_DIN3, (IEN | M0)},
> +	{ABEDMIC_CLK1, (M0)},
> +	{ABEDMIC_CLK2, (IEN | M1)},
> +	{ABEDMIC_CLK3, (M1)},
> +	{ABESLIMBUS1_CLOCK, (IEN | M1)},
> +	{ABESLIMBUS1_DATA, (IEN | M1)},
> +	{ABEMCBSP2_DR, (IEN | M0)},
> +	{ABEMCBSP2_DX, (M0)},
> +	{ABEMCBSP2_FSX, (IEN | M0)},
> +	{ABEMCBSP2_CLKX, (IEN | M0)},
> +	{ABEMCPDM_UL_DATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)},
> +	{ABEMCPDM_DL_DATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)},
> +	{ABEMCPDM_FRAME, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)},
> +	{ABEMCPDM_LB_CLK, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)},
> +	{WLSDIO_CLK, (PTU | IEN | M0)},
> +	{WLSDIO_CMD, (PTU | IEN | M0)},
> +	{WLSDIO_DATA0, (PTU | IEN | M0)},
> +	{WLSDIO_DATA1, (PTU | IEN | M0)},
> +	{WLSDIO_DATA2, (PTU | IEN | M0)},
> +	{WLSDIO_DATA3, (PTU | IEN | M0)},
> +	{UART5_RX, (PTU | IEN | M0)},
> +	{UART5_TX, (M0)},
> +	{UART5_CTS, (PTU | IEN | M0)},
> +	{UART5_RTS, (M0)},
> +	{I2C2_SCL, (IEN | M0)},
> +	{I2C2_SDA, (IEN | M0)},
> +	{MCSPI1_CLK, (M6)},
> +	{MCSPI1_SOMI, (IEN | M6)},
> +	{MCSPI1_SIMO, (PTD | M6)},
> +	{MCSPI1_CS0, (PTD | M6)},
> +	{MCSPI1_CS1, (PTD | IEN | M6)},
> +	{I2C5_SCL, (IEN | M0)},
> +	{I2C5_SDA, (IEN | M0)},
> +	{PERSLIMBUS2_CLOCK, (PTD | M6)},
> +	{PERSLIMBUS2_DATA, (PTD | IEN | M6)},
> +	{UART6_TX, (PTU | IEN | M6)},
> +	{UART6_RX, (PTU | IEN | M6)},
> +	{UART6_CTS, (PTU | IEN | M6)},
> +	{UART6_RTS, (PTU | M0)},
> +	{UART3_CTS_RCTX, (PTU | IEN | M6)},
> +	{UART3_RTS_IRSD, (PTU | IEN | M1)},
> +	{UART3_RX_IRRX, (PTU | IEN | M0)},
> +	{UART3_TX_IRTX, (M0)},
> +	{USBB3_HSIC_STROBE, (PTU | IEN | M0)},
> +	{USBB3_HSIC_DATA, (PTU | IEN | M0)},
> +	{SDCARD_CLK, (PTU | IEN | M0)},
> +	{SDCARD_CMD, (PTU | IEN | M0)},
> +	{SDCARD_DATA2, (PTU | IEN | M0)},
> +	{SDCARD_DATA3, (PTU | IEN | M0)},
> +	{SDCARD_DATA0, (PTU | IEN | M0)},
> +	{SDCARD_DATA1, (PTU | IEN | M0)},
> +	{USBD0_HS_DP, (IEN | M0)},
> +	{USBD0_HS_DM, (IEN | M0)},
> +	{I2C1_PMIC_SCL, (PTU | IEN | M0)},
> +	{I2C1_PMIC_SDA, (PTU | IEN | M0)},
> +	{USBD0_SS_RX, (IEN | M0)},
> +};
> +
> +static const struct pad_conf_entry wkup_padconf_array[] = {
> +	{LLIA_WAKEREQIN, (IEN | M1)},
> +	{LLIB_WAKEREQIN, (IEN | M1)},
> +	{DRM_EMU0, (PTU | IEN | M0)},
> +	{DRM_EMU1, (PTU | IEN | M0)},
> +	{JTAG_NTRST, (IEN | M0)},
> +	{JTAG_TCK, (IEN | M0)},
> +	{JTAG_RTCK, (M0)},
> +	{JTAG_TMSC, (IEN | M0)},
> +	{JTAG_TDI, (IEN | M0)},
> +	{JTAG_TDO, (M0)},
> +	{SYS_32K, (IEN | M0)},
> +	{FREF_CLK_IOREQ, (IEN | M0)},
> +	{FREF_CLK0_OUT, (M0)},
> +	{FREF_CLK1_OUT, (M0)},
> +	{FREF_CLK2_OUT, (M0)},
> +	{FREF_CLK2_REQ, (PTU | IEN | M6)},
> +	{FREF_CLK1_REQ, (PTD | IEN | M6)},
> +	{SYS_NRESPWRON, (IEN | M0)},
> +	{SYS_NRESWARM, (PTU | IEN | M0)},
> +	{SYS_PWR_REQ, (M0)},
> +	{SYS_NIRQ1, (PTU | IEN | M0)},
> +	{SYS_NIRQ2, (PTU | IEN | M0)},
> +	{SR_PMIC_SCL, (PTU | IEN | M0)},
> +	{SR_PMIC_SDA, (PTU | IEN | M0)},
> +	{SYS_BOOT0, (IEN | M0)},
> +	{SYS_BOOT1, (IEN | M0)},
> +	{SYS_BOOT2, (IEN | M0)},
> +	{SYS_BOOT3, (IEN | M0)},
> +	{SYS_BOOT4, (IEN | M0)},
> +	{SYS_BOOT5, (IEN | M0)},
> +};
> +
> +void set_muxconf_regs(void)
> +{
> +	omap5_do_set_mux(OMAP54XX_CONTROL_PADCONF_CORE, core_padconf_array,
> +			ARRAY_SIZE(core_padconf_array));
> +	omap5_do_set_mux(OMAP54XX_CONTROL_PADCONF_WKUP, wkup_padconf_array,
> +			ARRAY_SIZE(wkup_padconf_array));
> +}
> diff --git a/arch/arm/configs/omap5_sevm_defconfig b/arch/arm/configs/omap5_sevm_defconfig
> new file mode 100644
> index 0000000..5cd51bb
> --- /dev/null
> +++ b/arch/arm/configs/omap5_sevm_defconfig
> @@ -0,0 +1,68 @@
> +CONFIG_ARCH_OMAP=y
> +CONFIG_ARCH_OMAP5=y
> +CONFIG_MACH_OMAP5_SEVM=y
> +CONFIG_AEABI=y
> +CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y
> +CONFIG_ARM_UNWIND=y
> +CONFIG_MMU=y
> +CONFIG_TEXT_BASE=0x8f000000
> +CONFIG_MALLOC_SIZE=0x2000000
> +CONFIG_MALLOC_TLSF=y
> +CONFIG_KALLSYMS=y
> +CONFIG_PROMPT="barebox> "
> +CONFIG_LONGHELP=y
> +CONFIG_GLOB=y
> +CONFIG_HUSH_FANCY_PROMPT=y
> +CONFIG_CMDLINE_EDITING=y
> +CONFIG_AUTO_COMPLETE=y
> +# CONFIG_TIMESTAMP is not set
> +CONFIG_DEFAULT_ENVIRONMENT_GENERIC=y
> +CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/omap5_sevm/env"
> +CONFIG_CMD_EDIT=y
> +CONFIG_CMD_SLEEP=y
> +CONFIG_CMD_SAVEENV=y
> +CONFIG_CMD_LOADENV=y
> +CONFIG_CMD_EXPORT=y
> +CONFIG_CMD_PRINTENV=y
> +CONFIG_CMD_READLINE=y
> +CONFIG_CMD_TIME=y
> +CONFIG_CMD_ECHO_E=y
> +CONFIG_CMD_LOADB=y
> +CONFIG_CMD_IOMEM=y
> +CONFIG_CMD_FLASH=y
> +CONFIG_CMD_BOOTM_SHOW_TYPE=y
> +CONFIG_CMD_BOOTM_VERBOSE=y
> +CONFIG_CMD_BOOTM_INITRD=y
> +CONFIG_CMD_BOOTM_OFTREE=y
> +# CONFIG_CMD_BOOTU is not set
> +CONFIG_CMD_RESET=y
> +CONFIG_CMD_GO=y
> +CONFIG_CMD_TIMEOUT=y
> +CONFIG_CMD_PARTITION=y
> +CONFIG_CMD_MAGICVAR=y
> +CONFIG_CMD_MAGICVAR_HELP=y
> +CONFIG_CMD_GPIO=y
> +CONFIG_CMD_UNCOMPRESS=y
> +CONFIG_NET=y
> +CONFIG_NET_DHCP=y
> +CONFIG_NET_NFS=y
> +CONFIG_NET_PING=y
> +CONFIG_CMD_TFTP=y
> +CONFIG_FS_TFTP=y
> +CONFIG_DRIVER_SERIAL_NS16550=y
> +CONFIG_DRIVER_SERIAL_NS16550_OMAP_EXTENSIONS=y
> +CONFIG_DRIVER_NET_SMC911X=y
> +# CONFIG_SPI is not set
> +CONFIG_MTD=y
> +CONFIG_NAND=y
> +CONFIG_NAND_OMAP_GPMC=y
> +CONFIG_UBI=y
> +CONFIG_MCI=y
> +CONFIG_MCI_STARTUP=y
> +CONFIG_MCI_OMAP_HSMMC=y
> +CONFIG_FS_FAT=y
> +CONFIG_FS_FAT_WRITE=y
> +CONFIG_FS_FAT_LFN=y
> +CONFIG_ZLIB=y
> +CONFIG_LZO_DECOMPRESS=y
> +CONFIG_DEBUG_LL=y
> diff --git a/arch/arm/configs/omap5_sevm_xload_defconfig b/arch/arm/configs/omap5_sevm_xload_defconfig
> new file mode 100644
> index 0000000..2c47c87
> --- /dev/null
> +++ b/arch/arm/configs/omap5_sevm_xload_defconfig
> @@ -0,0 +1,44 @@
> +CONFIG_ARCH_OMAP=y
> +CONFIG_ARCH_OMAP5=y
> +CONFIG_OMAP_BUILD_IFT=y
> +CONFIG_MACH_OMAP5_SEVM=y
> +CONFIG_AEABI=y
> +CONFIG_THUMB2_BAREBOX=y
> +# CONFIG_CMD_ARM_CPUINFO is not set
> +# CONFIG_ARM_EXCEPTIONS is not set
> +CONFIG_MMU=y
> +CONFIG_TEXT_BASE=0x40300000
> +CONFIG_MEMORY_LAYOUT_FIXED=y
> +CONFIG_STACK_BASE=0x8f000000
> +CONFIG_MALLOC_BASE=0x84000000
> +CONFIG_MALLOC_SIZE=0x2000000
> +CONFIG_MALLOC_DUMMY=y
> +CONFIG_PROMPT="barebox> "
> +CONFIG_SHELL_NONE=y
> +# CONFIG_ERRNO_MESSAGES is not set
> +# CONFIG_TIMESTAMP is not set
> +# CONFIG_CONSOLE_FULL is not set
> +# CONFIG_DEFAULT_ENVIRONMENT is not set
> +# CONFIG_DRIVER_SERIAL_NS16550 is not set
> +# CONFIG_DRIVER_SERIAL_NS16550_OMAP_EXTENSIONS is not set
> +# CONFIG_SPI is not set
> +# CONFIG_MTD is not set
> +# CONFIG_MTD_WRITE is not set
> +# CONFIG_MTD_OOB_DEVICE is not set
> +CONFIG_NAND=y
> +# CONFIG_NAND_ECC_SOFT is not set
> +# CONFIG_NAND_ECC_HW_SYNDROME is not set
> +# CONFIG_NAND_ECC_HW_NONE is not set
> +# CONFIG_NAND_INFO is not set
> +# CONFIG_NAND_BBT is not set
> +CONFIG_NAND_OMAP_GPMC=y
> +CONFIG_MCI=y
> +CONFIG_MCI_STARTUP=y
> +# CONFIG_MCI_WRITE is not set
> +CONFIG_MCI_OMAP_HSMMC=y
> +# CONFIG_FS_RAMFS is not set
> +# CONFIG_FS_DEVFS is not set
> +CONFIG_FS_FAT=y
> +# CONFIG_DEBUG_LL is not set
> +# CONFIG_BANNER is not set
> +# CONFIG_MEMINFO is not set
> diff --git a/arch/arm/mach-omap/Kconfig b/arch/arm/mach-omap/Kconfig
> index 42e5f4a..0ad3864 100644
> --- a/arch/arm/mach-omap/Kconfig
> +++ b/arch/arm/mach-omap/Kconfig
> @@ -41,6 +41,14 @@ config ARCH_OMAP4
>  	help
>  	  Say Y here if you are using Texas Instrument's OMAP4 based platform
>  
> +config ARCH_OMAP5
> +	bool "OMAP5"
> +	select CPU_V7
> +	select GENERIC_GPIO
> +	select OMAP_CLOCK_SOURCE_S32K
> +	help
> +	  Say Y here if you are using Texas Instrument's OMAP5 based platform
> +
>  config ARCH_AM33XX
>  	bool "AM33xx"
>  	select CPU_V7
> @@ -115,6 +123,7 @@ config BOARDINFO
>  	default "Phytec phyCARD-A-L1" if MACH_PCAAL1
>  	default "Phytec phyCARD-A-XL2" if MACH_PCAAXL2
>  	default "Phytec phyCORE-AM335x" if MACH_PCM051
> +	default "Phytec phyCORE omap5_sevm" if MACH_OMAP5_SEVM
>  
>  choice
>  	prompt "Select OMAP board"
> @@ -177,6 +186,13 @@ config MACH_PCAAXL2
>  	help
>  	  Say Y here if you are using a phyCARD-A-XL1 PCA-A-XL1
>  
> +config MACH_OMAP5_SEVM
> +	bool "Phytec phyCORE omap5_sevm"
> +	depends on ARCH_OMAP5
> +	help
> +	  Say Y here if you are using Phytecs phyCORE omap5_sevm board
> +	  based on OMAP5
> +
>  config MACH_PCM051
>  	bool "Phytec phyCORE pcm051"
>  	select OMAP_CLOCK_ALL
> diff --git a/arch/arm/mach-omap/Makefile b/arch/arm/mach-omap/Makefile
> index d9e00f7..e65353f 100644
> --- a/arch/arm/mach-omap/Makefile
> +++ b/arch/arm/mach-omap/Makefile
> @@ -23,6 +23,8 @@ obj-$(CONFIG_ARCH_OMAP3) += omap3_generic.o auxcr.o
>  pbl-$(CONFIG_ARCH_OMAP3) += omap3_generic.o auxcr.o
>  obj-$(CONFIG_ARCH_OMAP4) += omap4_generic.o omap4_clock.o
>  pbl-$(CONFIG_ARCH_OMAP4) += omap4_generic.o omap4_clock.o
> +obj-$(CONFIG_ARCH_OMAP5) += omap5_generic.o omap5_clock.o
> +pbl-$(CONFIG_ARCH_OMAP5) += omap5_generic.o omap5_clock.o
>  obj-$(CONFIG_ARCH_AM33XX) += am33xx_generic.o am33xx_clock.o am33xx_mux.o
>  obj-$(CONFIG_OMAP3_CLOCK_CONFIG) += omap3_clock.o
>  pbl-$(CONFIG_OMAP3_CLOCK_CONFIG) += omap3_clock.o
> diff --git a/arch/arm/mach-omap/gpmc.c b/arch/arm/mach-omap/gpmc.c
> index bb84b38..1620f0f 100644
> --- a/arch/arm/mach-omap/gpmc.c
> +++ b/arch/arm/mach-omap/gpmc.c
> @@ -26,6 +26,7 @@
>  #include <errno.h>
>  #include <mach/omap3-silicon.h>
>  #include <mach/omap4-silicon.h>
> +#include <mach/omap5-silicon.h>
>  #include <mach/am33xx-silicon.h>
>  #include <mach/gpmc.h>
>  #include <mach/sys_info.h>
> @@ -39,6 +40,8 @@ static int gpmc_init(void)
>  	omap_gpmc_base = (void *)OMAP3_GPMC_BASE;
>  #elif defined(CONFIG_ARCH_OMAP4)
>  	omap_gpmc_base = (void *)OMAP44XX_GPMC_BASE;
> +#elif defined(CONFIG_ARCH_OMAP5)
> +	omap_gpmc_base = (void *)OMAP54XX_GPMC_BASE;
>  #elif defined(CONFIG_ARCH_AM33XX)
>  	omap_gpmc_base = (void *)AM33XX_GPMC_BASE;
>  #else
> diff --git a/arch/arm/mach-omap/include/mach/debug_ll.h b/arch/arm/mach-omap/include/mach/debug_ll.h
> index 38ca562..473d8f4 100644
> --- a/arch/arm/mach-omap/include/mach/debug_ll.h
> +++ b/arch/arm/mach-omap/include/mach/debug_ll.h
> @@ -39,6 +39,11 @@
>  #endif
>  #endif
>  
> +#ifdef CONFIG_ARCH_OMAP5
> +#include <mach/omap5-silicon.h>
> +#define UART_BASE	OMAP54XX_UART3_BASE
> +#endif
> +
>  #ifdef CONFIG_ARCH_AM33XX
>  #include <mach/am33xx-silicon.h>
>  #define UART_BASE	AM33XX_UART0_BASE
> diff --git a/arch/arm/mach-omap/include/mach/generic.h b/arch/arm/mach-omap/include/mach/generic.h
> index 7455404..f4917ba 100644
> --- a/arch/arm/mach-omap/include/mach/generic.h
> +++ b/arch/arm/mach-omap/include/mach/generic.h
> @@ -27,6 +27,12 @@
>  #define cpu_is_omap4xxx()	(0)
>  #endif
>  
> +#ifdef CONFIG_ARCH_OMAP5
> +#define cpu_is_omap5xxx()	(1)
> +#else
> +#define cpu_is_omap5xxx()	(0)
> +#endif
> +
>  enum omap_boot_src {
>  	OMAP_BOOTSRC_UNKNOWN,
>  	OMAP_BOOTSRC_MMC1,
> @@ -39,5 +45,6 @@ enum omap_boot_src omap_bootsrc(void);
>  enum omap_boot_src am33xx_bootsrc(void);
>  enum omap_boot_src omap3_bootsrc(void);
>  enum omap_boot_src omap4_bootsrc(void);
> +enum omap_boot_src omap5_bootsrc(void);
>  
>  #endif
> diff --git a/arch/arm/mach-omap/include/mach/gpmc_nand.h b/arch/arm/mach-omap/include/mach/gpmc_nand.h
> index 4a93465..5fe6d0f 100644
> --- a/arch/arm/mach-omap/include/mach/gpmc_nand.h
> +++ b/arch/arm/mach-omap/include/mach/gpmc_nand.h
> @@ -65,5 +65,6 @@ int omap_add_gpmc_nand_device(struct gpmc_nand_platform_data *pdata);
>  
>  extern struct gpmc_config omap3_nand_cfg;
>  extern struct gpmc_config omap4_nand_cfg;
> +extern struct gpmc_config omap5_nand_cfg;
>  
>  #endif				/* __ASM_OMAP_NAND_GPMC_H */
> diff --git a/arch/arm/mach-omap/include/mach/omap5-clock.h b/arch/arm/mach-omap/include/mach/omap5-clock.h
> new file mode 100644
> index 0000000..c606a60
> --- /dev/null
> +++ b/arch/arm/mach-omap/include/mach/omap5-clock.h
> @@ -0,0 +1,425 @@
> +/*
> + * (C) Copyright 2013
> + * Sam Solutions, <sam-solutions.com>
> + *
> + * Authors:
> + *	Uladzimir Bely <u.bely@sam-solutions.com>
> + *	Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
> + */
> +
> +/* CKGEN_PRM Registers */
> +#define CM_CLKSEL_ABE_DSS_SYS			0x4ae06100
> +#define CM_CLKSEL_WKUPAON			0x4ae06108
> +#define CM_CLKSEL_ABE_PLL_REF			0x4ae0610C
> +#define CM_CLKSEL_SYS				0x4ae06110
> +
> +#define CM_CLKSEL_SYS_12M0			0x1 /* 12.0MHz */
> +/* Reserved					0x2 */
> +#define CM_CLKSEL_SYS_16M8			0x3 /* 16.8MHz */
> +#define CM_CLKSEL_SYS_19M2			0x4 /* 19.2MHz */
> +#define CM_CLKSEL_SYS_26M0			0x5 /* 26.0MHz */
> +/* Reserved					0x6 */
> +#define CM_CLKSEL_SYS_38M4			0x7 /* 38.4MHz */
> +
> +/* WKUPAON_CM Registers offsets */
> +#define CM_WKUPAON_L4_WKUP_CLKCTRL_OFT		0x20
> +#define CM_WKUPAON_WD_TIMER2_CLKCTRL_OFT	0x30
> +#define CM_WKUPAON_GPIO1_CLKCTRL_OFT		0x38
> +#define CM_WKUPAON_TIMER1_CLKCTRL_OFT		0x40
> +#define CM_WKUPAON_COUNTER_32K_CLKCTRL_OFT	0x50
> +#define CM_WKUPAON_SAR_RAM_CLKCTRL_OFT		0x60
> +#define CM_WKUPAON_KBD_CLKCTRL_OFT		0x78
> +#define CM_WKUPAON_SCRM_CLKCTRL_OFT		0x90
> +#define CM_WKUPAON_IO_SRCOMP_CLKCTRL_OFT	0x98
> +
> +/* CKGEN_CM_CORE_AON Registers */
> +#define CM_CLKSEL_CORE				0x4a004100
> +#define CM_CLKSEL_ABE				0x4a004108
> +#define CM_DLL_CTRL				0x4a004110
> +#define CM_CLKMODE_DPLL_CORE			0x4a004120
> +#define CM_IDLEST_DPLL_CORE			0x4a004124
> +#define CM_AUTOIDLE_DPLL_CORE			0x4a004128
> +#define CM_CLKSEL_DPLL_CORE			0x4a00412c
> +#define CM_DIV_M2_DPLL_CORE			0x4a004130
> +#define CM_DIV_M3_DPLL_CORE			0x4a004134
> +#define CM_DIV_H11_DPLL_CORE			0x4a004138
> +#define CM_DIV_H12_DPLL_CORE			0x4a00413c
> +#define CM_DIV_H13_DPLL_CORE			0x4a004140
> +#define CM_DIV_H14_DPLL_CORE			0x4a004144
> +#define CM_SSC_DELTAMSTEP_DPLL_CORE		0x4a004148
> +#define CM_SSC_MODFREQDIV_DPLL_CORE		0x4a00414c
> +#define CM_DIV_H21_DPLL_CORE			0x4a004150 /* For rev. 2 */
> +#define CM_DIV_H22_DPLL_CORE			0x4a004154
> +#define CM_DIV_H23_DPLL_CORE			0x4a004158
> +#define CM_DIV_H24_DPLL_CORE			0x4a00415c /* For rev. 2 */
> +#define CM_CLKMODE_DPLL_MPU			0x4a004160
> +#define CM_IDLEST_DPLL_MPU			0x4a004164
> +#define CM_AUTOIDLE_DPLL_MPU			0x4a004168
> +#define CM_CLKSEL_DPLL_MPU			0x4a00416c
> +#define CM_DIV_M2_DPLL_MPU			0x4a004170
> +#define CM_SSC_DELTAMSTEP_DPLL_MPU		0x4a004188
> +#define CM_SSC_MODFREQDIV_DPLL_MPU		0x4a00418c
> +#define CM_BYPCLK_DPLL_MPU			0x4a00419c
> +#define CM_CLKMODE_DPLL_IVA			0x4a0041a0
> +#define CM_IDLEST_DPLL_IVA			0x4a0041a4
> +#define CM_AUTOIDLE_DPLL_IVA			0x4a0041a8
> +#define CM_CLKSEL_DPLL_IVA			0x4a0041ac
> +#define CM_DIV_H11_DPLL_IVA			0x4a0041b8
> +#define CM_DIV_H12_DPLL_IVA			0x4a0041bc
> +#define CM_SSC_DELTAMSTEP_DPLL_IVA		0x4a0041c8
> +#define CM_SSC_MODFREQDIV_DPLL_IVA		0x4a0041cc
> +#define CM_BYPCLK_DPLL_IVA			0x4a0041dc
> +#define CM_CLKMODE_DPLL_ABE			0x4a0041e0
> +#define CM_IDLEST_DPLL_ABE			0x4a0041e4
> +#define CM_AUTOIDLE_DPLL_ABE			0x4a0041e8
> +#define CM_CLKSEL_DPLL_ABE			0x4a0041ec
> +#define CM_DIV_M2_DPLL_ABE			0x4a0041f0
> +#define CM_DIV_M3_DPLL_ABE			0x4a0041f4
> +#define CM_SSC_DELTAMSTEP_DPLL_ABE		0x4a004208
> +#define CM_SSC_MODFREQDIV_DPLL_ABE		0x4a00420c
> +#define CM_SHADOW_FREQ_CONFIG1			0x4a004260
> +#define CM_SHADOW_FREQ_CONFIG2			0x4a004264
> +#define CM_DYN_DEP_PRESCAL			0x4a004270
> +#define CM_RESTORE_ST				0x4a004280
> +
> +/* DSP_CM_CORE_AON Registers */
> +#define CM_DSP_CLKSTCTRL			0x4a004400
> +#define CM_DSP_STATICDEP			0x4a004404
> +#define CM_DSP_DYNAMICDEP			0x4a004408
> +#define	CM_DSP_DSP_CLKCTRL			0x4a004420
> +
> +/* ABE_CM_CORE_AON Registers */
> +#define CM_ABE_CLKSTCTRL			0x4a004500
> +#define CM_ABE_L4_ABE_CLKCTRL			0x4a004520
> +#define CM_ABE_AESS_CLKCTRL			0x4a004528
> +#define CM_ABE_MCPDM_CLKCTRL			0x4a004530
> +#define CM_ABE_DMIC_CLKCTRL			0x4a004538
> +#define CM_ABE_MCASP_CLKCTRL			0x4a004540
> +#define CM_ABE_MCBSP1_CLKCTRL			0x4a004548
> +#define CM_ABE_MCBSP2_CLKCTRL			0x4a004550
> +#define CM_ABE_MCBSP3_CLKCTRL			0x4a004558
> +#define CM_ABE_SLIMBUS1_CLKCTRL			0x4a004560
> +#define CM_ABE_TIMER5_CLKCTRL			0x4a004568
> +#define CM_ABE_TIMER6_CLKCTRL			0x4a004570
> +#define CM_ABE_TIMER7_CLKCTRL			0x4a004578
> +#define CM_ABE_TIMER8_CLKCTRL			0x4a004580
> +#define CM_ABE_WD_TIMER3_CLKCTRL		0x4a004588
> +
> +/* CKGEN_CM_CORE Registers */
> +#define CM_CLKSEL_USB_60MHZ			0x4a008104
> +#define CM_CLKMODE_DPLL_PER			0x4a008140
> +#define CM_IDLEST_DPLL_PER			0x4a008144
> +#define CM_AUTOIDLE_DPLL_PER			0x4a008148
> +#define CM_CLKSEL_DPLL_PER			0x4a00814c
> +#define CM_DIV_M2_DPLL_PER			0x4a008150
> +#define CM_DIV_M3_DPLL_PER			0x4a008154
> +#define CM_DIV_H11_DPLL_PER			0x4a008158
> +#define CM_DIV_H12_DPLL_PER			0x4a00815c
> +#define CM_DIV_H14_DPLL_PER			0x4a008164
> +#define CM_SSC_DELTAMSTEP_DPLL_PER		0x4a008168
> +#define CM_SSC_MODFREQDIV_DPLL_PER		0x4a00816c
> +#define CM_CLKMODE_DPLL_USB			0x4a008180
> +#define CM_IDLEST_DPLL_USB			0x4a008184
> +#define CM_AUTOIDLE_DPLL_USB			0x4a008188
> +#define CM_CLKSEL_DPLL_USB			0x4a00818c
> +#define CM_DIV_M2_DPLL_USB			0x4a008190
> +#define CM_SSC_DELTAMSTEP_DPLL_USB		0x4a0081a8
> +#define CM_SSC_MODFREQDIV_DPLL_USB		0x4a0081ac
> +#define CM_CLKDCOLDO_DPLL_USB			0x4a0081b4
> +#define CM_CLKMODE_DPLL_UNIPRO2			0x4a0081c0
> +#define CM_IDLEST_DPLL_UNIPRO2			0x4a0081c4
> +#define CM_AUTOIDLE_DPLL_UNIPRO2		0x4a0081c8
> +#define CM_CLKSEL_DPLL_UNIPRO2			0x4a0081cc
> +#define CM_DIV_M2_DPLL_UNIPRO2			0x4a0081d0
> +#define CM_SSC_DELTAMSTEP_DPLL_UNIPRO2		0x4a0081e8
> +#define CM_SSC_MODFREQDIV_DPLL_UNIPRO2		0x4a0081ec
> +#define CM_CLKDCOLDO_DPLL_UNIPRO2		0x4a0081f4
> +#define CM_CLKMODE_DPLL_UNIPRO1			0x4a008200
> +#define CM_IDLEST_DPLL_UNIPRO1			0x4a008204
> +#define CM_AUTOIDLE_DPLL_UNIPRO1		0x4a008208
> +#define CM_CLKSEL_DPLL_UNIPRO1			0x4a00820c
> +#define CM_DIV_M2_DPLL_UNIPRO1			0x4a008210
> +#define CM_SSC_DELTAMSTEP_DPLL_UNIPRO1		0x4a008228
> +#define CM_SSC_MODFREQDIV_DPLL_UNIPRO1		0x4a00822c
> +#define CM_CLKDCOLDO_DPLL_UNIPRO1		0x4a008234
> +
> +/* CORE_CM_CORE Registers */
> +#define CM_L3MAIN1_CLKSTCTRL			0x4a008700
> +#define CM_L3MAIN1_DYNAMICDEP			0x4a008708
> +#define CM_L3MAIN1_L3_MAIN_1_CLKCTRL		0x4a008720
> +#define CM_L3MAIN2_CLKSTCTRL			0x4a008800
> +#define CM_L3MAIN2_DYNAMICDEP			0x4a008808
> +#define CM_L3MAIN2_L3_MAIN_2_CLKCTRL		0x4a008820
> +#define CM_L3MAIN2_GPMC_CLKCTRL			0x4a008828
> +#define CM_L3MAIN2_OCMC_RAM_CLKCTRL		0x4a008830
> +#define CM_IPU_CLKSTCTRL			0x4a008900
> +#define CM_IPU_STATICDEP			0x4a008904
> +#define CM_IPU_DYNAMICDEP			0x4a008908
> +#define CM_IPU_IPU_CLKCTRL			0x4a008920
> +#define CM_DMA_CLKSTCTRL			0x4a008a00
> +#define CM_DMA_STATICDEP			0x4a008a04
> +#define CM_DMA_DYNAMICDEP			0x4a008a08
> +#define CM_DMA_DMA_SYSTEM_CLKCTRL		0x4a008a20
> +#define CM_EMIF_CLKSTCTRL			0x4a008b00
> +#define CM_EMIF_DMM_CLKCTRL			0x4a008b20
> +#define CM_EMIF_EMIF_OCP_FW_CLKCTRL		0x4a008b28
> +#define CM_EMIF_EMIF1_CLKCTRL			0x4a008b30
> +#define CM_EMIF_EMIF2_CLKCTRL			0x4a008b38
> +#define CM_EMIF_EMIF_DLL_CLKCTRL		0x4a008b40
> +#define CM_C2C_CLKSTCTRL			0x4a008c00
> +#define CM_C2C_STATICDEP			0x4a008c04
> +#define CM_C2C_DYNAMICDEP			0x4a008c08
> +#define CM_C2C_C2C_CLKCTRL			0x4a008c20
> +#define CM_C2C_MODEM_ICR_CLKCTRL		0x4a008c28
> +#define CM_C2C_C2C_OCP_FW_CLKCTRL		0x4a008c30
> +#define CM_L4CFG_CLKSTCTRL			0x4a008d00
> +#define CM_L4CFG_DYNAMICDEP			0x4a008d08
> +#define CM_L4CFG_L4_CFG_CLKCTRL			0x4a008d20
> +#define CM_L4CFG_SPINLOCK_CLKCTRL		0x4a008d28
> +#define CM_L4CFG_MAILBOX_CLKCTRL		0x4a008d30
> +#define CM_L4CFG_SAR_ROM_CLKCTRL		0x4a008d38
> +#define CM_L4CFG_OCP2SCP2_CLKCTRL		0x4a008d40
> +#define CM_L3INSTR_CLKSTCTRL			0x4a008e00
> +#define CM_L3INSTR_L3_MAIN_3_CLKCTRL		0x4a008e20
> +#define CM_L3INSTR_L3_INSTR_CLKCTRL		0x4a008e28
> +#define CM_L3INSTR_OCP_WP_NOC_CLKCTRL		0x4a008e40
> +#define CM_L3INSTR_DLL_AGING_CLKCTRL		0x4a008e48
> +#define CM_L3INSTR_CTRL_MODULE_BANDGAP_CLKCTRL	0x4a008e50
> +
> +/* L4PER_CM_CORE Registers offsets*/
> +#define CM_L4PER_DYNAMICDEP_OFT			0x08
> +#define CM_L4PER_TIMER10_CLKCTRL_OFT		0x28
> +#define CM_L4PER_TIMER11_CLKCTRL_OFT		0x30
> +#define CM_L4PER_TIMER2_CLKCTRL_OFT		0x38
> +#define CM_L4PER_TIMER3_CLKCTRL_OFT		0x40
> +#define CM_L4PER_TIMER4_CLKCTRL_OFT		0x48
> +#define CM_L4PER_TIMER9_CLKCTRL_OFT		0x50
> +#define CM_L4PER_ELM_CLKCTRL_OFT		0x58
> +#define CM_L4PER_GPIO2_CLKCTRL_OFT		0x60
> +#define CM_L4PER_GPIO3_CLKCTRL_OFT		0x68
> +#define CM_L4PER_GPIO4_CLKCTRL_OFT		0x70
> +#define CM_L4PER_GPIO5_CLKCTRL_OFT		0x78
> +#define CM_L4PER_GPIO6_CLKCTRL_OFT		0x80
> +#define CM_L4PER_HDQ1W_CLKCTRL_OFT		0x88
> +#define CM_L4PER_I2C1_CLKCTRL_OFT		0xa0
> +#define CM_L4PER_I2C2_CLKCTRL_OFT		0xa8
> +#define CM_L4PER_I2C3_CLKCTRL_OFT		0xb0
> +#define CM_L4PER_I2C4_CLKCTRL_OFT		0xb8
> +#define CM_L4PER_L4_PER_CLKCTRL_OFT		0xc0
> +#define CM_L4PER_MCSPI1_CLKCTRL_OFT		0xf0
> +#define CM_L4PER_MCSPI2_CLKCTRL_OFT		0xf8
> +#define CM_L4PER_MCSPI3_CLKCTRL_OFT		0x100
> +#define CM_L4PER_MCSPI4_CLKCTRL_OFT		0x108
> +#define CM_L4PER_GPIO7_CLKCTRL_OFT		0x110
> +#define CM_L4PER_GPIO8_CLKCTRL_OFT		0x118
> +#define CM_L4PER_MMC3_CLKCTRL_OFT		0x120
> +#define CM_L4PER_MMC4_CLKCTRL_OFT		0x128
> +#define CM_L4PER_SLIMBUS2_CLKCTRL_OFT		0x138
> +#define CM_L4PER_UART1_CLKCTRL_OFT		0x140
> +#define CM_L4PER_UART2_CLKCTRL_OFT		0x148
> +#define CM_L4PER_UART3_CLKCTRL_OFT		0x150
> +#define CM_L4PER_UART4_CLKCTRL_OFT		0x158
> +#define CM_L4PER_MMC5_CLKCTRL_OFT		0x160
> +#define CM_L4PER_I2C5_CLKCTRL_OFT		0x168
> +#define CM_L4PER_UART5_CLKCTRL_OFT		0x170
> +#define CM_L4PER_UART6_CLKCTRL_OFT		0x178
> +#define CM_L4SEC_CLKSTCTRL_OFT			0x180
> +#define CM_L4SEC_STATICDEP_OFT			0x184
> +#define CM_L4SEC_DYNAMICDEP_OFT			0x188
> +#define CM_L4SEC_AES1_CLKCTRL_OFT		0x1a0
> +#define CM_L4SEC_AES2_CLKCTRL_OFT		0x1a8
> +#define CM_L4SEC_DES3DES_CLKCTRL_OFT		0x1b0
> +#define CM_L4SEC_FPKA_OFT			0x1b8
> +#define CM_L4SEC_RNG_CLKCTRL_OFT		0x1c0
> +#define CM_L4SEC_SHA2MD5_CLKCTRL_OFT		0x1c8
> +#define CM_L4SEC_DMA_CRYPTO_CLKCTRL_OFT		0x1d8
> +
> +/* L3INIT_CM_CORE Registers offsets */
> +#define CM_L3INIT_STATICDEP_OFT			0x04
> +#define CM_L3INIT_DYNAMICDEP_OFT		0x08
> +#define CM_L3INIT_MMC1_CLKCTRL_OFT		0x28
> +#define CM_L3INIT_MMC2_CLKCTRL_OFT		0x30
> +#define CM_L3INIT_HSI_CLKCTRL_OFT		0x38
> +#define CM_L3INIT_UNIPRO2_CLKCTRL_OFT		0x40
> +#define CM_L3INIT_MPHY_UNIPRO2_CLKCTRL_OFT	0x48
> +#define CM_L3INIT_USB_HOST_HS_CLKCTRL_OFT	0x58
> +#define CM_L3INIT_USB_TLL_HS_CLKCTRL_OFT	0x68
> +#define CM_L3INIT_IEEE1500_2_OCP_CLKCTRL_OFT	0x78
> +#define CM_L3INIT_SATA_CLKCTRL_OFT		0x88
> +#define CM_L3INIT_OCP2SCP1_CLKCTRL_OFT		0xe0
> +#define CM_L3INIT_OCP2SCP3_CLKCTRL_OFT		0xe8
> +#define CM_L3INIT_USB_OTG_SS_CLKCTRL_OFT	0xf0
> +
> +/* CAM_CM_CORE Registers offsets */
> +#define CM_CAM_STATICDEP_OFT			0x04
> +#define CM_CAM_DYNAMICDEP_OFT			0x08
> +#define CM_CAM_ISS_CLKCTRL_OFT			0x20
> +#define CM_CAM_FDIF_CLKCTRL_OFT			0x28
> +#define CM_CAM_CAL_CLKCTRL_OFT			0x30
> +
> +/* DSS_CM_CORE Registers offsets */
> +#define CM_DSS_STATICDEP_OFT			0x04
> +#define CM_DSS_DYNAMICDEP_OFT			0x08
> +#define CM_DSS_DSS_CLKCTRL_OFT			0x20
> +#define CM_DSS_BB2D_CLKCTRL_OFT			0x30 /* For rev. 2 */
> +
> +/* GPU_CM_CORE Registers offsets */
> +#define CM_GPU_STATICDEP_OFT			0x04
> +#define CM_GPU_DYNAMICDEP_OFT			0x08
> +#define CM_GPU_GPU_CLKCTRL_OFT			0x20
> +
> +#define PLL_STOP				0x1
> +#define PLL_LOW_POWER_BYPASS			0x5
> +#define PLL_FAST_RELOCK_BYPASS			0x6
> +#define PLL_LOCK				0x7
> +
> +/* TPS */
> +#define TPS62361_I2C_SLAVE_ADDR			0x60
> +#define TPS62361_REG_ADDR_SET0			0x0
> +#define TPS62361_REG_ADDR_SET1			0x1
> +#define TPS62361_REG_ADDR_SET2			0x2
> +#define TPS62361_REG_ADDR_SET3			0x3
> +#define TPS62361_REG_ADDR_CTRL			0x4
> +#define TPS62361_REG_ADDR_TEMP			0x5
> +#define TPS62361_REG_ADDR_RMP_CTRL		0x6
> +#define TPS62361_REG_ADDR_CHIP_ID		0x8
> +#define TPS62361_REG_ADDR_CHIP_ID_2		0x9
> +
> +#define TPS62361_BASE_VOLT_MV	500
> +#define TPS62361_VSEL0_GPIO	7
> +
> +/* Used to index into DPLL parameter tables */
> +struct	dpll_param {
> +	unsigned int m;
> +	unsigned int n;
> +	unsigned int m2;
> +	unsigned int m3;
> +	unsigned int h11;
> +	unsigned int h12;
> +	unsigned int h13;
> +	unsigned int h14;
> +	unsigned int h22;
> +	unsigned int h23;
> +};
> +
> +/* DPLL_MPU Preferred Settings       		   m    n  m2  m3  h11 h12 h13 h14 h22 h23 */
> +/* SYS_CLK = 12.0MHz */
> +#define OMAP5_MPU_DPLL_PARAM_12M0_HIGH		{ 275,  2,  1,  0,  0,  0,  0,  0,  0,  0}
> +#define OMAP5_MPU_DPLL_PARAM_12M0_NOM		{ 200,  2,  1,  0,  0,  0,  0,  0,  0,  0}
> +#define OMAP5_MPU_DPLL_PARAM_12M0_LOW		{ 200,  2,  2,  0,  0,  0,  0,  0,  0,  0}
> +/* SYS_CLK = 16.8MHz */
> +#define OMAP5_MPU_DPLL_PARAM_16M8_HIGH		{ 458,  6,  1,  0,  0,  0,  0,  0,  0,  0}
> +#define OMAP5_MPU_DPLL_PARAM_16M8_NOM		{ 375,  8,  1,  0,  0,  0,  0,  0,  0,  0}
> +#define OMAP5_MPU_DPLL_PARAM_16M8_LOW		{ 375,  8,  2,  0,  0,  0,  0,  0,  0,  0}
> +/* SYS_CLK = 19.2MHz */
> +#define OMAP5_MPU_DPLL_PARAM_19M2_HIGH		{ 229,  3,  1,  0,  0,  0,  0,  0,  0,  0}
> +#define OMAP5_MPU_DPLL_PARAM_19M2_NOM		{1000, 20,  1,  0,  0,  0,  0,  0,  0,  0}
> +#define OMAP5_MPU_DPLL_PARAM_19M2_LOW		{1000, 20,  2,  0,  0,  0,  0,  0,  0,  0}
> +/* SYS_CLK = 26.0MHz */
> +#define OMAP5_MPU_DPLL_PARAM_26M0_HIGH		{ 296,  6,  1,  0,  0,  0,  0,  0,  0,  0}
> +#define OMAP5_MPU_DPLL_PARAM_26M0_NOM		{ 400, 12,  1,  0,  0,  0,  0,  0,  0,  0}
> +#define OMAP5_MPU_DPLL_PARAM_26M0_LOW		{ 400, 12,  2,  0,  0,  0,  0,  0,  0,  0}
> +/* SYS_CLK = 38.4MHz */
> +#define OMAP5_MPU_DPLL_PARAM_38M4_HIGH		{ 229,  7,  1,  0,  0,  0,  0,  0,  0,  0}
> +#define OMAP5_MPU_DPLL_PARAM_38M4_NOM		{ 375, 17,  1,  0,  0,  0,  0,  0,  0,  0}
> +#define OMAP5_MPU_DPLL_PARAM_38M4_LOW		{ 375, 17,  2,  0,  0,  0,  0,  0,  0,  0}
> +
> +/* DPLL_IVA Preferred Settings       		   m    n  m2  m3  h11 h12 h13 h14 h22 h23 */
> +/* SYS_CLK = 12.0MHz */
> +#define OMAP5_IVA_DPLL_PARAM_12M0_OD		{ 133,  2,  0,  0,  2,  2,  0,  0,  0,  0}
> +#define OMAP5_IVA_DPLL_PARAM_12M0_NOM		{1165, 11,  0,  0,  5,  6,  0,  0,  0,  0}
> +#define OMAP5_IVA_DPLL_PARAM_12M0_LOW		{1165, 11,  0,  0, 10, 12,  0,  0,  0,  0}
> +/* SYS_CLK = 16.8MHz */
> +#define OMAP5_IVA_DPLL_PARAM_16M8_OD		{ 253,  7,  0,  0,  2,  2,  0,  0,  0,  0}
> +#define OMAP5_IVA_DPLL_PARAM_16M8_NOM		{ 208,  2,  0,  0,  5,  6,  0,  0,  0,  0}
> +#define OMAP5_IVA_DPLL_PARAM_16M8_LOW		{ 208,  2,  0,  0, 10, 12,  0,  0,  0,  0}
> +/* SYS_CLK = 19.2MHz */
> +#define OMAP5_IVA_DPLL_PARAM_19M2_OD		{  83,  2,  0,  0,  2,  2,  0,  0,  0,  0}
> +#define OMAP5_IVA_DPLL_PARAM_19M2_NOM		{ 182,  2,  0,  0,  5,  6,  0,  0,  0,  0}
> +#define OMAP5_IVA_DPLL_PARAM_19M2_LOW		{ 182,  2,  0,  0, 10, 12,  0,  0,  0,  0}
> +/* SYS_CLK = 26.0MHz */
> +#define OMAP5_IVA_DPLL_PARAM_26M0_OD		{ 143,  6,  0,  0,  2,  2,  0,  0,  0,  0}
> +#define OMAP5_IVA_DPLL_PARAM_26M0_NOM		{ 224,  4,  0,  0,  5,  6,  0,  0,  0,  0}
> +#define OMAP5_IVA_DPLL_PARAM_26M0_LOW		{ 224,  4,  0,  0, 10, 12,  0,  0,  0,  0}
> +/* SYS_CLK = 38.4MHz */
> +#define OMAP5_IVA_DPLL_PARAM_38M4_OD		{  83,  5,  0,  0,  2,  2,  0,  0,  0,  0}
> +#define OMAP5_IVA_DPLL_PARAM_38M4_NOM		{  91,  2,  0,  0,  5,  6,  0,  0,  0,  0}
> +#define OMAP5_IVA_DPLL_PARAM_38M4_LOW		{  91,  2,  0,  0, 10, 12,  0,  0,  0,  0}
> +
> +/* DPLL_CORE Preferred Settings       		   m    n  m2  m3  h11 h12 h13 h14 h22 h23 */
> +/* SYS_CLK = 12.0MHz */
> +#define OMAP5_CORE_DPLL_PARAM_12M0_NOM		{ 266,  2,  2,  5,  8,  4, 62,  4,  5,  7}
> +#define OMAP5_CORE_DPLL_PARAM_12M0_LOW		{ 266,  2,  4,  8,  8,  8, 62, 10, 10, 14}
> +/* SYS_CLK = 16.8MHz */
> +#define OMAP5_CORE_DPLL_PARAM_16M8_NOM		{ 443,  6,  2,  5,  8,  4, 62,  4,  5,  7}
> +#define OMAP5_CORE_DPLL_PARAM_16M8_LOW		{ 443,  6,  4,  8,  8,  8, 62, 10, 10, 14}
> +/* SYS_CLK = 19.2MHz */
> +#define OMAP5_CORE_DPLL_PARAM_19M2_NOM		{ 277,  4,  2,  5,  8,  4, 62,  4,  5,  7}
> +#define OMAP5_CORE_DPLL_PARAM_19M2_LOW		{ 277,  4,  4,  8,  8,  8, 62, 10, 10, 14}
> +/* SYS_CLK = 26.0MHz */
> +#define OMAP5_CORE_DPLL_PARAM_26M0_NOM		{ 368,  8,  2,  5,  8,  4, 62,  4,  5,  7}
> +#define OMAP5_CORE_DPLL_PARAM_26M0_LOW		{ 368,  8,  4,  8,  8,  8, 62, 10, 10, 14}
> +/* SYS_CLK = 38.4MHz */
> +#define OMAP5_CORE_DPLL_PARAM_38M4_NOM		{ 277,  9,  2,  5,  8,  4, 62,  4,  5,  7}
> +#define OMAP5_CORE_DPLL_PARAM_38M4_LOW		{ 277,  9,  4,  8,  8,  8, 62, 10, 10, 14}
> +
> +/* DPLL_PER Preferred Settings       		   m    n  m2  m3  h11 h12 h13 h14 h22 h23 */
> +/* SYS_CLK = 12.0MHz */
> +#define OMAP5_PER_DPLL_PARAM_12M0_NOM		{  32,  0,  4,  3,  6,  4,  0,  2,  0,  0}
> +#define OMAP5_PER_DPLL_PARAM_12M0_LOW		{  32,  0,  4,  4,  6,  4,  0,  4,  0,  0}
> +/* SYS_CLK = 16.8MHz */
> +#define OMAP5_PER_DPLL_PARAM_16M8_NOM		{ 160,  6,  4,  3,  6,  4,  0,  2,  0,  0}
> +#define OMAP5_PER_DPLL_PARAM_16M8_LOW		{ 160,  6,  4,  4,  6,  4,  0,  4,  0,  0}
> +/* SYS_CLK = 19.2MHz */
> +#define OMAP5_PER_DPLL_PARAM_19M2_NOM		{  20,  0,  4,  3,  6,  4,  0,  2,  0,  0}
> +#define OMAP5_PER_DPLL_PARAM_19M2_LOW		{  20,  0,  4,  4,  6,  4,  0,  4,  0,  0}
> +/* SYS_CLK = 26.0MHz */
> +#define OMAP5_PER_DPLL_PARAM_26M0_NOM		{ 192, 12,  4,  3,  6,  4,  0,  2,  0,  0}
> +#define OMAP5_PER_DPLL_PARAM_26M0_LOW		{ 192, 12,  4,  4,  6,  4,  0,  4,  0,  0}
> +/* SYS_CLK = 38.4MHz */
> +#define OMAP5_PER_DPLL_PARAM_38M4_NOM		{  10,  0,  4,  3,  6,  4,  0,  2,  0,  0}
> +#define OMAP5_PER_DPLL_PARAM_38M4_LOW		{  10,  0,  4,  4,  6,  4,  0,  4,  0,  0}
> +
> +/* DPLL_ABE Preferred Settings       		   m    n  m2  m3  h11 h12 h13 h14 h22 h23 */
> +#define OMAP5_ABE_DPLL_PARAM			{ 750,  0,  1,  1,  0,  0,  0,  0,  0,  0}
> +
> +/* DPLL_USB Preferred Settings       		   m    n  m2  m3  h11 h12 h13 h14 h22 h23 */
> +/* SYS_CLK = 12.0MHz */
> +#define OMAP5_USB_DPLL_PARAM_12M0		{ 400,  4,  2,  0,  0,  0,  0,  0,  0,  0}
> +/* SYS_CLK = 16.8MHz */
> +#define OMAP5_USB_DPLL_PARAM_16M8		{ 400,  6,  2,  0,  0,  0,  0,  0,  0,  0}
> +/* SYS_CLK = 19.2MHz */
> +#define OMAP5_USB_DPLL_PARAM_19M2		{ 400,  6,  2,  0,  0,  0,  0,  0,  0,  0}
> +/* SYS_CLK = 26.0MHz */
> +#define OMAP5_USB_DPLL_PARAM_26M0		{ 480, 12,  2,  0,  0,  0,  0,  0,  0,  0}
> +/* SYS_CLK = 38.4MHz */
> +#define OMAP5_USB_DPLL_PARAM_38M4		{ 480, 15,  2,  0,  0,  0,  0,  0,  0,  0}
> +
> +/* DPLL_UNIPRO1/UNIPRO2 Preferred Settings	   m    n  m2  m3  h11 h12 h13 h14 h22 h23 */
> +/* Different for DCO clock 1500MHz and 1250MHz */
> +/* SYS_CLK = 12.0MHz */
> +#define OMAP5_UNIPRO_DPLL_PARAM_12M0_DCO1M50	{ 520,  4,  4,  0,  0,  0,  0,  0,  0,  0}
> +#define OMAP5_UNIPRO_DPLL_PARAM_12M0_DCO1M25	{1822, 14,  4,  0,  0,  0,  0,  0,  0,  0}
> +/* SYS_CLK = 16.8MHz */
> +#define OMAP5_UNIPRO_DPLL_PARAM_16M8_DCO1M50	{ 520,  6,  4,  0,  0,  0,  0,  0,  0,  0}
> +#define OMAP5_UNIPRO_DPLL_PARAM_16M8_DCO1M25	{1822, 20,  4,  0,  0,  0,  0,  0,  0,  0}
> +/* SYS_CLK = 19.2MHz */
> +#define OMAP5_UNIPRO_DPLL_PARAM_19M2_DCO1M50	{ 520,  7,  4,  0,  0,  0,  0,  0,  0,  0}
> +#define OMAP5_UNIPRO_DPLL_PARAM_19M2_DCO1M25	{ 911, 11,  4,  0,  0,  0,  0,  0,  0,  0}
> +/* SYS_CLK = 26.0MHz */
> +#define OMAP5_UNIPRO_DPLL_PARAM_26M0_DCO1M50	{ 528, 10,  4,  0,  0,  0,  0,  0,  0,  0}
> +#define OMAP5_UNIPRO_DPLL_PARAM_26M0_DCO1M25	(1850, 32,  4,  0,  0,  0,  0,  0,  0,  0}
> +/* SYS_CLK = 38.4MHz */
> +#define OMAP5_UNIPRO_DPLL_PARAM_38M4_DCO1M50	{ 520, 15,  4,  0,  0,  0,  0,  0,  0,  0}
> +#define OMAP5_UNIPRO_DPLL_PARAM_38M4_DCO1M25	{ 911, 23,  4,  0,  0,  0,  0,  0,  0,  0}
> +
> +void omap5_configure_mpu_dpll(const struct dpll_param *dpll_param);
> +void omap5_configure_iva_dpll(const struct dpll_param *dpll_param);
> +void omap5_configure_core_dpll_no_lock(const struct dpll_param *param);
> +void omap5_configure_per_dpll(const struct dpll_param *dpll_param);
> +void omap5_configure_abe_dpll(const struct dpll_param *dpll_param);
> +void omap5_configure_usb_dpll(const struct dpll_param *dpll_param);
> +void omap5_lock_core_dpll(void);
> +void omap5_lock_core_dpll_shadow(const struct dpll_param *param);
> +void omap5_enable_all_clocks(void);
> +
> diff --git a/arch/arm/mach-omap/include/mach/omap5-devices.h b/arch/arm/mach-omap/include/mach/omap5-devices.h
> new file mode 100644
> index 0000000..adef686
> --- /dev/null
> +++ b/arch/arm/mach-omap/include/mach/omap5-devices.h
> @@ -0,0 +1,21 @@
> +#ifndef __MACH_OMAP5_DEVICES_H
> +#define __MACH_OMAP5_DEVICES_H
> +
> +#include <driver.h>
> +#include <sizes.h>
> +#include <mach/devices.h>
> +#include <mach/omap5-silicon.h>
> +#include <mach/omap_hsmmc.h>
> +
> +static inline struct device_d *omap54xx_add_uart3(void)
> +{
> +	return omap_add_uart(2, OMAP54XX_UART3_BASE);
> +}
> +
> +static inline struct device_d *omap54xx_add_mmc1(struct omap_hsmmc_platform_data *pdata)
> +{
> +	return add_generic_device("omap5-hsmmc", 0, NULL,
> +			OMAP54XX_MMC1_BASE, SZ_4K, IORESOURCE_MEM, pdata);
> +}
> +
> +#endif /* __MACH_OMAP5_DEVICES_H */
> diff --git a/arch/arm/mach-omap/include/mach/omap5-mux.h b/arch/arm/mach-omap/include/mach/omap5-mux.h
> new file mode 100644
> index 0000000..4e2b3fb
> --- /dev/null
> +++ b/arch/arm/mach-omap/include/mach/omap5-mux.h
> @@ -0,0 +1,321 @@
> +/*
> + * (C) Copyright 2013
> + * Sam Solutions, <sam-solutions.com>
> + *
> + * Authors:
> + *	Uladzimir Bely <u.bely@sam-solutions.com>
> + *	Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
> + *
> + * Derived from OMAP5 work in U-Boot project by
> + * Richard Woodruff		<r-woodruff2@ti.com>
> + * Aneesh V			<aneesh@ti.com>
> + * Balaji Krishnamoorthy	<balajitk@ti.com>
> + * (Copyright 2004-2009, Texas Instruments Incorporated)
> + */
> +
> +#ifndef _MUX_OMAP5_H_
> +#define _MUX_OMAP5_H_
> +
> +#include <asm/types.h>
> +
> +struct pad_conf_entry {
> +	u16 offset;
> +	u16 val;
> +};
> +
> +#define OFF_PD			(0 << 12)
> +#define OFF_PU			(0 << 12)
> +#define OFF_OUT_PTD		(0 << 10)
> +#define OFF_OUT_PTU		(0 << 10)
> +#define OFF_IN			(0 << 10)
> +#define OFF_OUT			(0 << 10)
> +#define OFF_EN			(0 << 9)
> +
> +#define IEN			(1 << 8)
> +#define IDIS			(0 << 8)
> +#define PTU			(3 << 3)
> +#define PTD			(1 << 3)
> +#define EN			(1 << 3)
> +#define DIS			(0 << 3)
> +
> +#define M0			0
> +#define M1			1
> +#define M2			2
> +#define M3			3
> +#define M4			4
> +#define M5			5
> +#define M6			6
> +#define M7			7
> +
> +#define SAFE_MODE		M7
> +
> +#define OFF_IN_PD		0
> +#define OFF_IN_PU		0
> +#define OFF_OUT_PD		0
> +#define OFF_OUT_PU		0
> +
> +/* CTRL_MODULE_CORE_PAT Registers */
> +/* Base address is 0x4a002800 */
> +#define CORE_REVISION		0x00
> +#define CORE_HWINFO		0x04
> +#define CORE_SYSCONFIG		0x10
> +#define EMMC_CLK		0x40
> +#define EMMC_CMD		0x42
> +#define EMMC_DATA0		0x44
> +#define EMMC_DATA1		0x46
> +#define EMMC_DATA2		0x48
> +#define EMMC_DATA3		0x4a
> +#define EMMC_DATA4		0x4c
> +#define EMMC_DATA5		0x4e
> +#define EMMC_DATA6		0x50
> +#define EMMC_DATA7		0x52
> +#define C2C_CLKOUT0		0x54
> +#define C2C_CLKOUT1		0x56
> +#define C2C_CLKIN0		0x58
> +#define C2C_CLKIN1		0x5a
> +#define C2C_DATAIN0		0x5c
> +#define C2C_DATAIN1		0x5e
> +#define C2C_DATAIN2		0x60
> +#define C2C_DATAIN3		0x62
> +#define C2C_DATAIN4		0x64
> +#define C2C_DATAIN5		0x66
> +#define C2C_DATAIN6		0x68
> +#define C2C_DATAIN7		0x6a
> +#define C2C_DATAOUT0		0x6c
> +#define C2C_DATAOUT1		0x6e
> +#define C2C_DATAOUT2		0x70
> +#define C2C_DATAOUT3		0x72
> +#define C2C_DATAOUT4		0x74
> +#define C2C_DATAOUT5		0x76
> +#define C2C_DATAOUT6		0x78
> +#define C2C_DATAOUT7		0x7a
> +#define C2C_DATA8		0x7c
> +#define C2C_DATA9		0x7e
> +#define C2C_DATA10		0x80
> +#define C2C_DATA11		0x82
> +#define C2C_DATA12		0x84
> +#define C2C_DATA13		0x86
> +#define C2C_DATA14		0x88
> +#define C2C_DATA15		0x8a
> +#define LLIA_WAKEREQOUT		0x8c
> +#define LLIB_WAKEREQOUT		0x8e
> +#define HSI1_ACREADY		0x90
> +#define HSI1_CAREADY		0x92
> +#define HSI1_ACWAKE		0x94
> +#define HSI1_CAWAKE		0x96
> +#define HSI1_ACFLAG		0x98
> +#define HSI1_ACDATA		0x9a
> +#define HSI1_CAFLAG		0x9c
> +#define HSI1_CADATA		0x9e
> +#define UART1_TX		0xa0
> +#define UART1_CTS		0xa2
> +#define UART1_RX		0xa4
> +#define UART1_RTS		0xa6
> +#define HSI2_CAREADY		0xa8
> +#define HSI2_ACREADY		0xaa
> +#define HSI2_CAWAKE		0xac
> +#define HSI2_ACWAKE		0xae
> +#define HSI2_CAFLAG		0xb0
> +#define HSI2_CADATA		0xb2
> +#define HSI2_ACFLAG		0xb4
> +#define HSI2_ACDATA		0xb6
> +#define UART2_RTS		0xb8
> +#define UART2_CTS		0xba
> +#define UART2_RX		0xbc
> +#define UART2_TX		0xbe
> +#define USBB1_HSIC_STROBE	0xc0
> +#define USBB1_HSIC_DATA		0xc2
> +#define USBB2_HSIC_STROBE	0xc4
> +#define USBB2_HSIC_DATA		0xc6
> +#define TIMER10_PWM_EVT		0xc8
> +#define DSIPORTA_TE0		0xca
> +#define DSIPORTA_LANE0X		0xcc
> +#define DSIPORTA_LANE0Y		0xce
> +#define DSIPORTA_LANE1X		0xd0
> +#define DSIPORTA_LANE1Y		0xd2
> +#define DSIPORTA_LANE2X		0xd4
> +#define DSIPORTA_LANE2Y		0xd6
> +#define DSIPORTA_LANE3X		0xd8
> +#define DSIPORTA_LANE3Y		0xda
> +#define DSIPORTA_LANE4X		0xdc
> +#define DSIPORTA_LANE4Y		0xde
> +#define DSIPORTC_LANE0X		0xe0
> +#define DSIPORTC_LANE0Y		0xe2
> +#define DSIPORTC_LANE1X		0xe4
> +#define DSIPORTC_LANE1Y		0xe6
> +#define DSIPORTC_LANE2X		0xe8
> +#define DSIPORTC_LANE2Y		0xea
> +#define DSIPORTC_LANE3X		0xec
> +#define DSIPORTC_LANE3Y		0xee
> +#define DSIPORTC_LANE4X		0xf0
> +#define DSIPORTC_LANE4Y		0xf2
> +#define DSIPORTC_TE0		0xf4
> +#define TIMER9_PWM_EVT		0xf6
> +#define I2C4_SCL		0xf8
> +#define I2C4_SDA		0xfa
> +#define MCSPI2_CLK		0xfc
> +#define MCSPI2_SIMO		0xfe
> +#define MCSPI2_SOMI		0x100
> +#define MCSPI2_CS0		0x102
> +#define RFBI_DATA15		0x104
> +#define RFBI_DATA14		0x106
> +#define RFBI_DATA13		0x108
> +#define RFBI_DATA12		0x10a
> +#define RFBI_DATA11		0x10c
> +#define RFBI_DATA10		0x10e
> +#define RFBI_DATA9		0x110
> +#define RFBI_DATA8		0x112
> +#define RFBI_DATA7		0x114
> +#define RFBI_DATA6		0x116
> +#define RFBI_DATA5		0x118
> +#define RFBI_DATA4		0x11a
> +#define RFBI_DATA3		0x11c
> +#define RFBI_DATA2		0x11e
> +#define RFBI_DATA1		0x120
> +#define RFBI_DATA0		0x122
> +#define RFBI_WE			0x124
> +#define RFBI_CS0		0x126
> +#define RFBI_A0			0x128
> +#define RFBI_RE			0x12a
> +#define RFBI_HSYNC0		0x12c
> +#define RFBI_TE_VSYNC0		0x12e
> +#define GPIO6_182		0x130
> +#define GPIO6_183		0x132
> +#define GPIO6_184		0x134
> +#define GPIO6_185		0x136
> +#define GPIO6_186		0x138
> +#define GPIO6_187		0x13a
> +#define HDMI_CEC		0x13c
> +#define HDMI_HPD		0x13e
> +#define HDMI_DDC_SCL		0x140
> +#define HDMI_DDC_SDA		0x142
> +#define CSIPORTC_LANE0X		0x144
> +#define CSIPORTC_LANE0Y		0x146
> +#define CSIPORTC_LANE1X		0x148
> +#define CSIPORTC_LANE1Y		0x14a
> +#define CSIPORTB_LANE0X		0x14c
> +#define CSIPORTB_LANE0Y		0x14e
> +#define CSIPORTB_LANE1X		0x150
> +#define CSIPORTB_LANE1Y		0x152
> +#define CSIPORTB_LANE2X		0x154
> +#define CSIPORTB_LANE2Y		0x156
> +#define CSIPORTA_LANE0X		0x158
> +#define CSIPORTA_LANE0Y		0x15a
> +#define CSIPORTA_LANE1X		0x15c
> +#define CSIPORTA_LANE1Y		0x15e
> +#define CSIPORTA_LANE2X		0x160
> +#define CSIPORTA_LANE2Y		0x162
> +#define CSIPORTA_LANE3X		0x164
> +#define CSIPORTA_LANE3Y		0x166
> +#define CSIPORTA_LANE4X		0x168
> +#define CSIPORTA_LANE4Y		0x16a
> +#define CAM_SHUTTER		0x16c
> +#define CAM_STROBE		0x16e
> +#define CAM_GLOBALRESET		0x170
> +#define TIMER11_PWM_EVT		0x172
> +#define TIMER5_PWM_EVT		0x174
> +#define TIMER6_PWM_EVT		0x176
> +#define TIMER8_PWM_EVT		0x178
> +#define I2C3_SCL		0x17a
> +#define I2C3_SDA		0x17c
> +#define GPIO8_233		0x17e
> +#define GPIO8_234		0x180
> +#define ABE_CLKS		0x182
> +#define ABEDMIC_DIN1		0x184
> +#define ABEDMIC_DIN2		0x186
> +#define ABEDMIC_DIN3		0x188
> +#define ABEDMIC_CLK1		0x18a
> +#define ABEDMIC_CLK2		0x18c
> +#define ABEDMIC_CLK3		0x18e
> +#define ABESLIMBUS1_CLOCK	0x190
> +#define ABESLIMBUS1_DATA	0x192
> +#define ABEMCBSP2_DR		0x194
> +#define ABEMCBSP2_DX		0x196
> +#define ABEMCBSP2_FSX		0x198
> +#define ABEMCBSP2_CLKX		0x19a
> +#define ABEMCPDM_UL_DATA	0x19c
> +#define ABEMCPDM_DL_DATA	0x19e
> +#define ABEMCPDM_FRAME		0x1a0
> +#define ABEMCPDM_LB_CLK		0x1a2
> +#define WLSDIO_CLK		0x1a4
> +#define WLSDIO_CMD		0x1a6
> +#define WLSDIO_DATA0		0x1a8
> +#define WLSDIO_DATA1		0x1aa
> +#define WLSDIO_DATA2		0x1ac
> +#define WLSDIO_DATA3		0x1ae
> +#define UART5_RX		0x1b0
> +#define UART5_TX		0x1b2
> +#define UART5_CTS		0x1b4
> +#define UART5_RTS		0x1b6
> +#define I2C2_SCL		0x1b8
> +#define I2C2_SDA		0x1ba
> +#define MCSPI1_CLK		0x1bc
> +#define MCSPI1_SOMI		0x1be
> +#define MCSPI1_SIMO		0x1c0
> +#define MCSPI1_CS0		0x1c2
> +#define MCSPI1_CS1		0x1c4
> +#define I2C5_SCL		0x1c6
> +#define I2C5_SDA		0x1c8
> +#define PERSLIMBUS2_CLOCK	0x1ca /* GPIO5_145 in rev. 2 */
> +#define PERSLIMBUS2_DATA	0x1cc /* GPIO5_146 in rev. 2 */
> +#define UART6_TX		0x1ce
> +#define UART6_RX		0x1d0
> +#define UART6_CTS		0x1d2
> +#define UART6_RTS		0x1d4
> +#define UART3_CTS_RCTX		0x1d6
> +#define UART3_RTS_IRSD		0x1d8
> +#define UART3_TX_IRTX		0x1da
> +#define UART3_RX_IRRX		0x1dc
> +#define USBB3_HSIC_STROBE	0x1de
> +#define USBB3_HSIC_DATA		0x1e0
> +#define SDCARD_CLK		0x1e2
> +#define SDCARD_CMD		0x1e4
> +#define SDCARD_DATA2		0x1e6
> +#define SDCARD_DATA3		0x1e8
> +#define SDCARD_DATA0		0x1ea
> +#define SDCARD_DATA1		0x1ec
> +#define USBD0_HS_DP		0x1ee
> +#define USBD0_HS_DM		0x1f0
> +#define I2C1_PMIC_SCL		0x1f2
> +#define I2C1_PMIC_SDA		0x1f4
> +#define USBD0_SS_RX		0x1f6
> +
> +/* CTRL_MODULE_WKUP_PAD Registers offsets */
> +/* Base address is 0x4ae0c800 */
> +#define WKUP_REVISION		0x00
> +#define WKUP_HWINFO		0x04
> +#define WKUP_SYSCONFIG		0x10
> +#define LLIA_WAKEREQIN		0x40
> +#define LLIB_WAKEREQIN		0x42
> +#define DRM_EMU0		0x44
> +#define DRM_EMU1		0x46
> +#define JTAG_NTRST		0x48
> +#define JTAG_TCK		0x4a
> +#define JTAG_RTCK		0x4c
> +#define JTAG_TMSC		0x4e
> +#define JTAG_TDI		0x50
> +#define JTAG_TDO		0x52
> +#define SYS_32K			0x54
> +#define FREF_CLK_IOREQ		0x56
> +#define FREF_CLK0_OUT		0x58
> +#define FREF_CLK1_OUT		0x5a
> +#define FREF_CLK2_OUT		0x5c
> +#define FREF_CLK2_REQ		0x5e
> +#define FREF_CLK1_REQ		0x60
> +#define SYS_NRESPWRON		0x62
> +#define SYS_NRESWARM		0x64
> +#define SYS_PWR_REQ		0x66
> +#define SYS_NIRQ1		0x68
> +#define SYS_NIRQ2		0x6a
> +#define SR_PMIC_SCL		0x6c
> +#define SR_PMIC_SDA		0x6e
> +#define SYS_BOOT0		0x70
> +#define SYS_BOOT1		0x72
> +#define SYS_BOOT2		0x74
> +#define SYS_BOOT3		0x76
> +#define SYS_BOOT4		0x78
> +#define SYS_BOOT5		0x7a
> +
> +void omap5_do_set_mux(u32 base, struct pad_conf_entry const *array, int size);
> +
> +#endif /* _MUX_OMAP5_H_ */
> diff --git a/arch/arm/mach-omap/include/mach/omap5-silicon.h b/arch/arm/mach-omap/include/mach/omap5-silicon.h
> new file mode 100644
> index 0000000..b29242d
> --- /dev/null
> +++ b/arch/arm/mach-omap/include/mach/omap5-silicon.h
> @@ -0,0 +1,235 @@
> +/*
> + * (C) Copyright 2013
> + * Sam Solutions, <sam-solutions.com>
> + *
> + * Authors:
> + *	Uladzimir Bely <u.bely@sam-solutions.com>
> + *	Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
> + *
> + * Derived from OMAP4 work by
> + *	Aneesh V <aneesh@ti.com>
> + */
> +
> +#ifndef _OMAP5_H_
> +#define _OMAP5_H_
> +
> +#if !(defined(__KERNEL_STRICT_NAMES) || defined(__ASSEMBLY__))
> +#include <asm/types.h>
> +#endif /* !(__KERNEL_STRICT_NAMES || __ASSEMBLY__) */
> +
> +/* L4 Peripherals - L4 Wakeup and L4 Core now */
> +#define OMAP54XX_L4_CFG_BASE				0x4A000000
> +#define OMAP54XX_L4_WKUP_BASE				0x4Ae00000
> +#define OMAP54XX_L4_PER_BASE				0x48000000
> +
> +/* EMIF and DMM registers */
> +#define OMAP54XX_EMIF1_BASE				0x4c000000
> +#define OMAP54XX_EMIF2_BASE				0x4d000000
> +
> +#define OMAP54XX_DRAM_ADDR_SPACE_START			0x80000000
> +#define OMAP54XX_DRAM_ADDR_SPACE_END			0xff000000
> +
> +/* CONTROL */
> +#define OMAP54XX_CTRL_BASE				(OMAP54XX_L4_CFG_BASE + 0x2000)
> +#define OMAP54XX_CONTROL_PADCONF_CORE			(OMAP54XX_CTRL_BASE + 0x0800)
> +#define OMAP54XX_CONTROL_PADCONF_WKUP			(OMAP54XX_L4_WKUP_BASE + 0xc800)
> +
> +/* PRM */
> +#define OMAP54XX_PRM_VC_VAL_BYPASS			(OMAP54XX_L4_WKUP_BASE + 0x7ba0)
> +#define OMAP54XX_PRM_VC_CFG_I2C_MODE			(OMAP54XX_L4_WKUP_BASE + 0x7bb4)
> +#define OMAP54XX_PRM_VC_CFG_I2C_CLK			(OMAP54XX_L4_WKUP_BASE + 0x7bb8)
> +#define OMAP54XX_PRM_VC_VAL_BYPASS_VALID_BIT		0x1000000
> +#define OMAP54XX_PRM_VC_VAL_BYPASS_SLAVEADDR_SHIFT	0
> +#define OMAP54XX_PRM_VC_VAL_BYPASS_SLAVEADDR_MASK	0x7F
> +#define OMAP54XX_PRM_VC_VAL_BYPASS_REGADDR_SHIFT	8
> +#define OMAP54XX_PRM_VC_VAL_BYPASS_REGADDR_MASK		0xFF
> +#define OMAP54XX_PRM_VC_VAL_BYPASS_DATA_SHIFT		16
> +#define OMAP54XX_PRM_VC_VAL_BYPASS_DATA_MASK		0xFF
> +
> +#define VDD_MPU						1150
> +#define VDD_MM						1150
> +#define VDD_CORE					1150
> +
> +#define SMPS_BASE_VOLT_UV				500000
> +#define SMPS_I2C_SLAVE_ADDR				0x12
> +#define SMPS_REG_ADDR_12_MPU				0x23
> +#define SMPS_REG_ADDR_45_IVA				0x2B
> +#define SMPS_REG_ADDR_8_CORE				0x37
> +
> +/* IRQ */
> +#define OMAP54XX_PRM_IRQSTATUS_MPU			(OMAP54XX_L4_WKUP_BASE + 0x6010)
> +
> +/* UART */
> +#define OMAP54XX_UART1_BASE				(OMAP54XX_L4_PER_BASE + 0x6a000)
> +#define OMAP54XX_UART2_BASE				(OMAP54XX_L4_PER_BASE + 0x6c000)
> +#define OMAP54XX_UART3_BASE				(OMAP54XX_L4_PER_BASE + 0x20000)
> +
> +/* I2C */
> +#define OMAP54XX_I2C1_BASE				(OMAP54XX_L4_PER_BASE + 0x070000)
> +#define OMAP54XX_I2C2_BASE				(OMAP54XX_L4_PER_BASE + 0x072000)
> +#define OMAP54XX_I2C3_BASE				(OMAP54XX_L4_PER_BASE + 0x060000)
> +
> +/* General Purpose Timers */
> +#define OMAP54XX_GPT1_BASE				(OMAP54XX_L4_WKUP_BASE + 0x18000)
> +#define OMAP54XX_GPT2_BASE				(OMAP54XX_L4_PER_BASE  + 0x32000)
> +#define OMAP54XX_GPT3_BASE				(OMAP54XX_L4_PER_BASE  + 0x34000)
> +
> +/* Watchdog Timer2 - MPU watchdog */
> +#define OMAP54XX_WDT2_BASE				(OMAP54XX_L4_WKUP_BASE + 0x14000)
> +
> +#define OMAP54XX_SCRM_BASE				(OMAP54XX_L4_WKUP_BASE + 0xa000)
> +#define OMAP54XX_SCRM_AUXCLK1				(OMAP54XX_SCRM_BASE + 0x314)
> +#define OMAP54XX_SCRM_AUXCLK3				(OMAP54XX_SCRM_BASE + 0x31c)
> +
> +/* 32KTIMER */
> +#define OMAP54XX_32KTIMER_BASE				(OMAP54XX_L4_WKUP_BASE + 0x4000)
> +
> +/* MMC */
> +#define OMAP54XX_MMC1_BASE				(OMAP54XX_L4_PER_BASE + 0x09C000)
> +#define OMAP54XX_MMC2_BASE				(OMAP54XX_L4_PER_BASE + 0x0B4000)
> +#define OMAP54XX_MMC3_BASE				(OMAP54XX_L4_PER_BASE + 0x0ad000)
> +#define OMAP54XX_MMC4_BASE				(OMAP54XX_L4_PER_BASE + 0x0d1000)
> +#define OMAP54XX_MMC5_BASE				(OMAP54XX_L4_PER_BASE + 0x0d5000)
> +
> +/* GPIO */
> +#define OMAP54XX_GPIO1_BASE				(OMAP54XX_L4_WKUP_BASE + 0x10000)
> +#define OMAP54XX_GPIO2_BASE				(OMAP54XX_L4_PER_BASE  + 0x55000)
> +#define OMAP54XX_GPIO3_BASE				(OMAP54XX_L4_PER_BASE  + 0x57000)
> +#define OMAP54XX_GPIO4_BASE				(OMAP54XX_L4_PER_BASE  + 0x59000)
> +#define OMAP54XX_GPIO5_BASE				(OMAP54XX_L4_PER_BASE  + 0x5b000)
> +#define OMAP54XX_GPIO6_BASE				(OMAP54XX_L4_PER_BASE  + 0x5d000)
> +
> +/* GPMC */
> +#define OMAP54XX_GPMC_BASE				0x50000000
> +
> +/* DMM */
> +#define OMAP54XX_DMM_BASE				0x4e000000
> +
> +/* Memory Adapter */
> +#define OMAP54XX_MA_BASE				0x482AF000
> +
> +/*
> + * Hardware Register Details
> + */
> +
> +/* Watchdog Timer */
> +#define WD_UNLOCK1					0xAAAA
> +#define WD_UNLOCK2					0x5555
> +
> +/* GP Timer */
> +#define TCLR_ST						(0x1 << 0)
> +#define TCLR_AR						(0x1 << 1)
> +#define TCLR_PRE					(0x1 << 5)
> +
> +/* PRM */
> +#define PRM_BASE					0x4AE06000
> +#define PRM_DEVICE_BASE					(PRM_BASE + 0x1B00)
> +
> +#define PRM_RSTCTRL					PRM_DEVICE_BASE
> +#define PRM_RSTCTRL_RESET				0x01
> +
> +/*
> + * Non-secure SRAM Addresses
> + * Non-secure RAM starts at 0x40300000 for GP devices. But we keep SRAM_BASE
> + * at 0x40304000(EMU base) so that our code works for both EMU and GP
> + */
> +#define NON_SECURE_SRAM_START				0x40304000
> +#define NON_SECURE_SRAM_END				0x4030E000 /* Not inclusive */
> +/* base address for indirect vectors (internal boot mode) */
> +#define SRAM_ROM_VECT_BASE				0x4030D000
> +
> +/* OMAP5 silicon revisions */
> +#define OMAP543X_SILICON_ID_INVALID			0
> +#define OMAP5430_ES1_0					0x54300100
> +#define OMAP5430_ES2_0					0x54300200
> +#define OMAP5432_ES1_0					0x54320100
> +#define OMAP5432_ES2_0					0x54320200
> +
> +struct omap5_ddr_regs {
> +	u32 freq;
> +	u32 sdram_config_init;
> +	u32 sdram_config;
> +	u32 ref_ctrl;
> +	u32 sdram_tim1;
> +	u32 sdram_tim2;
> +	u32 sdram_tim3;
> +	u32 read_idle_ctrl;
> +	u32 zq_config;
> +	u32 temp_alert_config;
> +	u32 emif_ddr_phy_ctlr_1_init;
> +	u32 emif_ddr_phy_ctlr_1;
> +	u32 emif_ddr_phy_ctlr_2;
> +	u32 emif_ddr_ext_phy_ctrl_1_init;
> +	u32 emif_ddr_ext_phy_ctrl_1;
> +	u32 emif_ddr_ext_phy_ctrl_2_init;
> +	u32 emif_ddr_ext_phy_ctrl_2;
> +	u32 emif_ddr_ext_phy_ctrl_3_init;
> +	u32 emif_ddr_ext_phy_ctrl_3;
> +	u32 emif_ddr_ext_phy_ctrl_4_init;
> +	u32 emif_ddr_ext_phy_ctrl_4;
> +	u32 emif_ddr_ext_phy_ctrl_5_init;
> +	u32 emif_ddr_ext_phy_ctrl_5;
> +	u32 emif_ddr_ext_phy_ctrl_6_init;
> +	u32 emif_ddr_ext_phy_ctrl_6;
> +	u32 emif_ddr_ext_phy_ctrl_7_init;
> +	u32 emif_ddr_ext_phy_ctrl_7;
> +	u32 emif_ddr_ext_phy_ctrl_8_init;
> +	u32 emif_ddr_ext_phy_ctrl_8;
> +	u32 emif_ddr_ext_phy_ctrl_9_init;
> +	u32 emif_ddr_ext_phy_ctrl_9;
> +	u32 emif_ddr_ext_phy_ctrl_10_init;
> +	u32 emif_ddr_ext_phy_ctrl_10;
> +	u32 emif_ddr_ext_phy_ctrl_11_init;
> +	u32 emif_ddr_ext_phy_ctrl_11;
> +	u32 emif_ddr_ext_phy_ctrl_12_init;
> +	u32 emif_ddr_ext_phy_ctrl_12;
> +	u32 emif_ddr_ext_phy_ctrl_13_init;
> +	u32 emif_ddr_ext_phy_ctrl_13;
> +	u32 emif_ddr_ext_phy_ctrl_14_init;
> +	u32 emif_ddr_ext_phy_ctrl_14;
> +	u32 emif_ddr_ext_phy_ctrl_15_init;
> +	u32 emif_ddr_ext_phy_ctrl_15;
> +	u32 emif_ddr_ext_phy_ctrl_16_init;
> +	u32 emif_ddr_ext_phy_ctrl_16;
> +	u32 emif_ddr_ext_phy_ctrl_17_init;
> +	u32 emif_ddr_ext_phy_ctrl_17;
> +	u32 emif_ddr_ext_phy_ctrl_18_init;
> +	u32 emif_ddr_ext_phy_ctrl_18;
> +	u32 emif_ddr_ext_phy_ctrl_19_init;
> +	u32 emif_ddr_ext_phy_ctrl_19;
> +	u32 emif_ddr_ext_phy_ctrl_20_init;
> +	u32 emif_ddr_ext_phy_ctrl_20;
> +	u32 emif_ddr_ext_phy_ctrl_21_init;
> +	u32 emif_ddr_ext_phy_ctrl_21;
> +	u32 emif_ddr_ext_phy_ctrl_22_init;
> +	u32 emif_ddr_ext_phy_ctrl_22;
> +	u32 emif_ddr_ext_phy_ctrl_23_init;
> +	u32 emif_ddr_ext_phy_ctrl_23;
> +	u32 emif_ddr_ext_phy_ctrl_24_init;
> +	u32 emif_ddr_ext_phy_ctrl_24;
> +	u32 emif_ddr_ext_phy_ctrl_25_init;
> +	u32 emif_ddr_ext_phy_ctrl_25;
> +	u32 emif_ddr_ext_phy_ctrl_26_init;
> +	u32 emif_ddr_ext_phy_ctrl_26;
> +	u32 emif_ddr_ext_phy_ctrl_27_init;
> +	u32 emif_ddr_ext_phy_ctrl_27;
> +	u32 emif_ddr_ext_phy_ctrl_28_init;
> +	u32 emif_ddr_ext_phy_ctrl_28;
> +	u32 emif_ddr_ext_phy_ctrl_29_init;
> +	u32 emif_ddr_ext_phy_ctrl_29;
> +	u32 emif_ddr_ext_phy_ctrl_30_init;
> +	u32 emif_ddr_ext_phy_ctrl_30;
> +	u32 emif_rd_wr_lvl_rmp_win;
> +	u32 emif_rd_wr_lvl_rmp_ctl;
> +	u32 emif_rd_wr_lvl_ctl;
> +	u32 emif_rd_wr_exec_thresh;
> +};
> +
> +struct dpll_param;
> +
> +void omap5_ddr_init(const struct omap5_ddr_regs *ddr_regs, const struct dpll_param *);
> +void omap5_power_i2c_send(u32);
> +unsigned int omap5_revision(void);
> +void omap5_scale_vcores(void);
> +
> +#endif /* _OMAP5_H_ */
> diff --git a/arch/arm/mach-omap/omap5_clock.c b/arch/arm/mach-omap/omap5_clock.c
> new file mode 100644
> index 0000000..6cba922
> --- /dev/null
> +++ b/arch/arm/mach-omap/omap5_clock.c
> @@ -0,0 +1,385 @@
> +/*
> + * (C) Copyright 2013
> + * Sam Solutions, <sam-solutions.com>
> + *
> + * Authors:
> + *	Uladzimir Bely <u.bely@sam-solutions.com>
> + *	Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
> + *
> + * Derived from OMAP4 work
> + */
> +
> +#include <common.h>
> +#include <io.h>
> +#include <mach/syslib.h>
> +#include <mach/clocks.h>
> +#include <mach/omap5-silicon.h>
> +#include <mach/omap5-clock.h>
> +
> +#define LDELAY	12000000
> +
> +#define PM_DSS_PWRSTCTRL 0x4AE07400
> +
> +void omap5_configure_mpu_dpll(const struct dpll_param *dpll_param)
> +{
> +	/* Unlock the MPU dpll */
> +	sr32(CM_CLKMODE_DPLL_MPU, 0, 3, PLL_FAST_RELOCK_BYPASS);
> +	wait_on_value((1 << 0), 0, CM_IDLEST_DPLL_MPU, LDELAY);
> +
> +	/* Disable DPLL auto control */
> +	sr32(CM_AUTOIDLE_DPLL_MPU, 0, 3, 0x0);
> +
> +	/* Set M,N,M2 values */
> +	sr32(CM_CLKSEL_DPLL_MPU, 8, 11, dpll_param->m);
> +	sr32(CM_CLKSEL_DPLL_MPU, 0, 7, dpll_param->n);
> +	sr32(CM_DIV_M2_DPLL_MPU, 0, 5, dpll_param->m2);
> +
> +	/* Lock the MPU dpll */
> +	sr32(CM_CLKMODE_DPLL_MPU, 0, 3, PLL_LOCK);
> +	wait_on_value((1 << 0), 1, CM_IDLEST_DPLL_MPU, LDELAY);
> +
> +	return;
> +}
> +
> +void omap5_configure_iva_dpll(const struct dpll_param *dpll_param)
> +{
> +	/* Unlock the IVA dpll */
> +	sr32(CM_CLKMODE_DPLL_IVA, 0, 3, PLL_FAST_RELOCK_BYPASS);
> +	wait_on_value((1 << 0), 0, CM_IDLEST_DPLL_IVA, LDELAY);
> +
> +	/* CM_BYPCLK_DPLL_IVA = CORE_X2_CLK/2 */
> +	sr32(CM_BYPCLK_DPLL_IVA, 0, 2, 0x1);
> +
> +	/* Disable DPLL auto control */
> +	sr32(CM_AUTOIDLE_DPLL_IVA, 0, 3, 0x0);
> +
> +	/* Set M,N,H11,H12 */
> +	sr32(CM_CLKSEL_DPLL_IVA, 8, 11, dpll_param->m);
> +	sr32(CM_CLKSEL_DPLL_IVA, 0, 7, dpll_param->n);
> +	sr32(CM_DIV_H11_DPLL_IVA, 0, 5, dpll_param->h11);
> +	sr32(CM_DIV_H12_DPLL_IVA, 0, 5, dpll_param->h12);
> +
> +	/* Lock the IVA dpll */
> +	sr32(CM_CLKMODE_DPLL_IVA, 0, 3, PLL_LOCK);
> +	wait_on_value((1 << 0), 1, CM_IDLEST_DPLL_IVA, LDELAY);
> +
> +	return;
> +}
> +
> +void omap5_configure_core_dpll_no_lock(const struct dpll_param *dpll_param)
> +{
> +	/* CORE_CLK=CORE_X2_CLK/2, L3_CLK=CORE_CLK/2, L4_CLK=L3_CLK/2 */
> +	sr32(CM_CLKSEL_CORE, 0, 32, 0x110);
> +
> +	/* Unlock the CORE dpll */
> +	sr32(CM_CLKMODE_DPLL_CORE, 0, 3, PLL_FAST_RELOCK_BYPASS);
> +	wait_on_value((1 << 0), 0, CM_IDLEST_DPLL_CORE, LDELAY);
> +
> +	/* Disable DPLL auto control */
> +	sr32(CM_AUTOIDLE_DPLL_CORE, 0, 3, 0x0);
> +
> +	/* Set M,N,M2, M3, H11, H12, H13, H14, H22, H23 */
> +	sr32(CM_CLKSEL_DPLL_CORE, 8, 11, dpll_param->m);
> +	sr32(CM_CLKSEL_DPLL_CORE, 0, 7, dpll_param->n);
> +	sr32(CM_DIV_M2_DPLL_CORE, 0, 5, dpll_param->m2);
> +	sr32(CM_DIV_M3_DPLL_CORE, 0, 5, dpll_param->m3);
> +	sr32(CM_DIV_H11_DPLL_CORE, 0, 5, dpll_param->h11);
> +	sr32(CM_DIV_H12_DPLL_CORE, 0, 5, dpll_param->h12);
> +	sr32(CM_DIV_H13_DPLL_CORE, 0, 5, dpll_param->h13);
> +	sr32(CM_DIV_H14_DPLL_CORE, 0, 5, dpll_param->h14);
> +	sr32(CM_DIV_H22_DPLL_CORE, 0, 5, dpll_param->h22);
> +	sr32(CM_DIV_H23_DPLL_CORE, 0, 5, dpll_param->h23);
> +
> +	return;
> +}
> +
> +void omap5_configure_per_dpll(const struct dpll_param *dpll_param)
> +{
> +	/* Unlock the PER dpll */
> +	sr32(CM_CLKMODE_DPLL_PER, 0, 3, PLL_FAST_RELOCK_BYPASS);
> +	wait_on_value((1 << 0), 0, CM_IDLEST_DPLL_PER, LDELAY);
> +
> +	/* Disable DPLL auto control */
> +	sr32(CM_AUTOIDLE_DPLL_PER, 0, 3, 0x0);
> +
> +	/* Set M,N,M2, M3, H11, H12, H14 */
> +	sr32(CM_CLKSEL_DPLL_PER, 8, 11, dpll_param->m);
> +	sr32(CM_CLKSEL_DPLL_PER, 0, 7, dpll_param->n);
> +	sr32(CM_DIV_M2_DPLL_PER, 0, 5, dpll_param->m2);
> +	sr32(CM_DIV_M3_DPLL_PER, 0, 5, dpll_param->m3);
> +	sr32(CM_DIV_H11_DPLL_PER, 0, 5, dpll_param->h11);
> +	sr32(CM_DIV_H12_DPLL_PER, 0, 5, dpll_param->h12);
> +	sr32(CM_DIV_H14_DPLL_PER, 0, 5, dpll_param->h14);
> +
> +	/* Lock the per dpll */
> +	sr32(CM_CLKMODE_DPLL_PER, 0, 3, PLL_LOCK);
> +	wait_on_value((1 << 0), 1, CM_IDLEST_DPLL_PER, LDELAY);
> +
> +	return;
> +}
> +
> +void omap5_configure_abe_dpll(const struct dpll_param *dpll_param)
> +{
> +	/* Some options to achieve 196.608MHz from 32768 Hz */
> +	sr32(CM_CLKMODE_DPLL_ABE, 8, 1, 1);  /* DPLL_DRIFTGUARD_EN_MASK */
> +	sr32(CM_CLKMODE_DPLL_ABE, 9, 1, 1);  /* DPLL_RELOCK_RAMP_EN_MASK */
> +	sr32(CM_CLKMODE_DPLL_ABE, 10, 1, 1); /* DPLL_LPMODE_EN_MASK */
> +	sr32(CM_CLKMODE_DPLL_ABE, 11, 1, 1); /* DPLL_REGM4XEN_MASK */
> +
> +	/* Spend 4 REFCLK cycles at each stage */
> +	sr32(CM_CLKMODE_DPLL_ABE, 5, 3, 7);
> +
> +	/* Select SYS_32K as ref clk for ABE dpll */
> +	sr32(CM_CLKSEL_ABE_PLL_REF, 0, 1, 1);
> +
> +	/* Unlock the ABE dpll */
> +	sr32(CM_CLKMODE_DPLL_ABE, 0, 3, PLL_LOW_POWER_BYPASS);
> +	wait_on_value((1 << 0), 0, CM_IDLEST_DPLL_ABE, LDELAY);
> +
> +	/* Disable DPLL auto control */
> +	sr32(CM_AUTOIDLE_DPLL_ABE, 0, 3, 0x0);
> +
> +	/* Set M,N,M2, M3 */
> +	sr32(CM_CLKSEL_DPLL_ABE, 8, 11, dpll_param->m);
> +	sr32(CM_CLKSEL_DPLL_ABE, 0, 7, dpll_param->n);
> +	sr32(CM_DIV_M2_DPLL_ABE, 0, 5, dpll_param->m2);
> +	sr32(CM_DIV_M3_DPLL_ABE, 0, 5, dpll_param->m3);
> +
> +	/* Lock the abe dpll */
> +	sr32(CM_CLKMODE_DPLL_ABE, 0, 3, PLL_LOCK);
> +	wait_on_value((1 << 0), 1, CM_IDLEST_DPLL_ABE, LDELAY);
> +
> +	return;
> +}
> +
> +void omap5_configure_usb_dpll(const struct dpll_param *dpll_param)
> +{
> +	/* Select the 60Mhz clock 480/8 = 60*/
> +	sr32(CM_CLKSEL_USB_60MHZ, 0, 32, 0x1);
> +
> +	/* Unlock the USB dpll */
> +	sr32(CM_CLKMODE_DPLL_USB, 0, 3, PLL_FAST_RELOCK_BYPASS);
> +	wait_on_value((1 << 0), 0, CM_IDLEST_DPLL_USB, LDELAY);
> +
> +	/* Disable auto control */
> +	sr32(CM_AUTOIDLE_DPLL_USB, 0, 3, 0x0);
> +
> +	/* Set M,N,M2 */
> +	sr32(CM_CLKSEL_DPLL_USB, 8, 12, dpll_param->m);
> +	sr32(CM_CLKSEL_DPLL_USB, 0, 8, dpll_param->n);
> +	sr32(CM_DIV_M2_DPLL_USB, 0, 7, dpll_param->m2);
> +	sr32(CM_DIV_M2_DPLL_USB, 9, 1, 0x1);
> +
> +	/* Lock the usb dpll */
> +	sr32(CM_CLKMODE_DPLL_USB, 0, 3, PLL_LOCK);
> +	wait_on_value((1 << 0), 1, CM_IDLEST_DPLL_USB, LDELAY);
> +
> +	return;
> +}
> +
> +void omap5_lock_core_dpll(void)
> +{
> +	/* Lock the core dpll */
> +	sr32(CM_CLKMODE_DPLL_CORE, 0, 3, PLL_LOCK);
> +	wait_on_value((1 << 0), 1, CM_IDLEST_DPLL_CORE, LDELAY);
> +
> +	return;
> +}
> +
> +void omap5_lock_core_dpll_shadow(const struct dpll_param *param)
> +{
> +	/* Lock the core dpll using freq update method */
> +	*(volatile int*)CM_CLKMODE_DPLL_CORE = PLL_LOCK;
> +
> +	/* CM_SHADOW_FREQ_CONFIG1: DLL_OVERRIDE = 1(hack), DLL_RESET = 1,
> +	 * DPLL_CORE_M2_DIV = 1, DPLL_CORE_DPLL_EN = 0x7, FREQ_UPDATE = 1
> +	 */
> +	*(volatile int*)CM_SHADOW_FREQ_CONFIG1 = 0x70D | (param->m2 << 11);
> +
> +	/* Wait for Freq_Update to get cleared: CM_SHADOW_FREQ_CONFIG1 */
> +	while(((*(volatile int*)CM_SHADOW_FREQ_CONFIG1) & 0x1) == 0x1);
> +
> +	/* Wait for DPLL to Lock : CM_IDLEST_DPLL_CORE */
> +	wait_on_value((1 << 0), 1, CM_IDLEST_DPLL_CORE, LDELAY);
> +}
> +
> +void omap5_enable_all_clocks(void)
> +{
> +	unsigned int rev = omap5_revision();
> +	u32 wkup_base = 0x4ae07800;
> +	u32 l4per_base = 0x4a009400;
> +	u32 l3init_base = 0x4a009300;
> +	u32 cam_base = 0x4a009000;
> +	u32 dss_base = 0x4a009100;
> +	u32 gpu_base = 0x4a009200;
> +
> +	if (rev == OMAP5430_ES2_0 || rev == OMAP5432_ES2_0) {
> +		wkup_base = 0x4ae07900;
> +		l4per_base = 0x4a009000;
> +		l3init_base = 0x4a009600;
> +		cam_base = 0x4a009300;
> +		dss_base = 0x4a009400;
> +		gpu_base = 0x4a009500;
> +	}
> +
> +	/* Enable DSP clocks */
> +	sr32(CM_DSP_DSP_CLKCTRL, 0, 32, 0x1);
> +	sr32(CM_DSP_CLKSTCTRL, 0, 32, 0x2);
> +
> +	wait_on_value((1 << 8), 0, CM_DSP_CLKSTCTRL, LDELAY);
> +
> +	/* ABE clocks */
> +	sr32(CM_ABE_CLKSTCTRL, 0, 32, 0x3);
> +	sr32(CM_ABE_AESS_CLKCTRL, 0, 32, 0x2);
> +	sr32(CM_ABE_MCPDM_CLKCTRL, 0, 32, 0x2);
> +	sr32(CM_ABE_DMIC_CLKCTRL, 0, 32, 0x2);
> +	sr32(CM_ABE_MCASP_CLKCTRL, 0, 32, 0x2);
> +	sr32(CM_ABE_MCBSP1_CLKCTRL, 0, 32, 0x08000002);
> +	sr32(CM_ABE_MCBSP2_CLKCTRL, 0, 32, 0x08000002);
> +	sr32(CM_ABE_MCBSP3_CLKCTRL, 0, 32, 0x08000002);
> +	sr32(CM_ABE_SLIMBUS1_CLKCTRL, 0, 32, 0x0f02);
> +	sr32(CM_ABE_TIMER5_CLKCTRL, 0, 32, 0x2);
> +	sr32(CM_ABE_TIMER6_CLKCTRL, 0, 32, 0x2);
> +	sr32(CM_ABE_TIMER7_CLKCTRL, 0, 32, 0x2);
> +	sr32(CM_ABE_TIMER8_CLKCTRL, 0, 32, 0x2);
> +	sr32(CM_ABE_WD_TIMER3_CLKCTRL, 0, 32, 0x2);
> +	/* Disable sleep transitions */
> +	sr32(CM_ABE_CLKSTCTRL, 0, 32, 0x0);
> +
> +	/* L4PER clocks */
> +	sr32(l4per_base, 0, 32, 0x2);
> +	sr32(l4per_base + CM_L4PER_TIMER10_CLKCTRL_OFT, 0, 32, 0x2);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_TIMER10_CLKCTRL_OFT, LDELAY);
> +	sr32(l4per_base + CM_L4PER_TIMER11_CLKCTRL_OFT, 0, 32, 0x2);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_TIMER11_CLKCTRL_OFT, LDELAY);
> +	sr32(l4per_base + CM_L4PER_TIMER2_CLKCTRL_OFT, 0, 32, 0x2);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_TIMER2_CLKCTRL_OFT, LDELAY);
> +	sr32(l4per_base + CM_L4PER_TIMER3_CLKCTRL_OFT, 0, 32, 0x2);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_TIMER3_CLKCTRL_OFT, LDELAY);
> +	sr32(l4per_base + CM_L4PER_TIMER4_CLKCTRL_OFT, 0, 32, 0x2);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_TIMER4_CLKCTRL_OFT, LDELAY);
> +	sr32(l4per_base + CM_L4PER_TIMER9_CLKCTRL_OFT, 0, 32, 0x2);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_TIMER9_CLKCTRL_OFT, LDELAY);
> +
> +	/* GPIO clocks */
> +	sr32(l4per_base + CM_L4PER_GPIO2_CLKCTRL_OFT, 0, 32, 0x1);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_GPIO2_CLKCTRL_OFT, LDELAY);
> +	sr32(l4per_base + CM_L4PER_GPIO3_CLKCTRL_OFT, 0, 32, 0x1);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_GPIO3_CLKCTRL_OFT, LDELAY);
> +	sr32(l4per_base + CM_L4PER_GPIO4_CLKCTRL_OFT, 0, 32, 0x1);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_GPIO4_CLKCTRL_OFT, LDELAY);
> +	sr32(l4per_base + CM_L4PER_GPIO5_CLKCTRL_OFT, 0, 32, 0x1);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_GPIO5_CLKCTRL_OFT, LDELAY);
> +	sr32(l4per_base + CM_L4PER_GPIO6_CLKCTRL_OFT, 0, 32, 0x1);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_GPIO6_CLKCTRL_OFT, LDELAY);
> +
> +	sr32(l4per_base + CM_L4PER_HDQ1W_CLKCTRL_OFT, 0, 32, 0x1);
> +
> +	/* I2C clocks */
> +	sr32(l4per_base + CM_L4PER_I2C1_CLKCTRL_OFT, 0, 32, 0x2);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_I2C1_CLKCTRL_OFT, LDELAY);
> +	sr32(l4per_base + CM_L4PER_I2C2_CLKCTRL_OFT, 0, 32, 0x2);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_I2C2_CLKCTRL_OFT, LDELAY);
> +	sr32(l4per_base + CM_L4PER_I2C3_CLKCTRL_OFT, 0, 32, 0x2);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_I2C3_CLKCTRL_OFT, LDELAY);
> +	sr32(l4per_base + CM_L4PER_I2C4_CLKCTRL_OFT, 0, 32, 0x2);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_I2C4_CLKCTRL_OFT, LDELAY);
> +
> +	/* MCSPI clocks */
> +	sr32(l4per_base + CM_L4PER_MCSPI1_CLKCTRL_OFT, 0, 32, 0x2);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_MCSPI1_CLKCTRL_OFT, LDELAY);
> +	sr32(l4per_base + CM_L4PER_MCSPI2_CLKCTRL_OFT, 0, 32, 0x2);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_MCSPI2_CLKCTRL_OFT, LDELAY);
> +	sr32(l4per_base + CM_L4PER_MCSPI3_CLKCTRL_OFT, 0, 32, 0x2);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_MCSPI3_CLKCTRL_OFT, LDELAY);
> +	sr32(l4per_base + CM_L4PER_MCSPI4_CLKCTRL_OFT, 0, 32, 0x2);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_MCSPI4_CLKCTRL_OFT, LDELAY);
> +
> +	/* MMC3-5 clocks */
> +	sr32(l4per_base + CM_L4PER_MMC3_CLKCTRL_OFT, 0, 32, 0x2);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_MMC3_CLKCTRL_OFT, LDELAY);
> +	sr32(l4per_base + CM_L4PER_MMC4_CLKCTRL_OFT, 0, 32, 0x2);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_MMC4_CLKCTRL_OFT, LDELAY);
> +	sr32(l4per_base + CM_L4PER_MMC5_CLKCTRL_OFT, 0, 32, 0x2);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_MMC5_CLKCTRL_OFT, LDELAY);
> +
> +	/* UART clocks */
> +	sr32(l4per_base + CM_L4PER_UART1_CLKCTRL_OFT, 0, 32, 0x2);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_UART1_CLKCTRL_OFT, LDELAY);
> +	sr32(l4per_base + CM_L4PER_UART2_CLKCTRL_OFT, 0, 32, 0x2);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_UART2_CLKCTRL_OFT, LDELAY);
> +	sr32(l4per_base + CM_L4PER_UART3_CLKCTRL_OFT, 0, 32, 0x2);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_UART3_CLKCTRL_OFT, LDELAY);
> +	sr32(l4per_base + CM_L4PER_UART4_CLKCTRL_OFT, 0, 32, 0x2);
> +	wait_on_value((1 << 17)|(1 << 16), 0, l4per_base + CM_L4PER_UART4_CLKCTRL_OFT, LDELAY);
> +
> +	/* MMC1-2 clocks */
> +	sr32(l3init_base + CM_L3INIT_MMC1_CLKCTRL_OFT, 0, 2, 0x2);
> +	sr32(l3init_base + CM_L3INIT_MMC1_CLKCTRL_OFT, 24, 1, 0x1);
> +	sr32(l3init_base + CM_L3INIT_MMC1_CLKCTRL_OFT, 25, 1, 0x0);
> +	sr32(l3init_base + CM_L3INIT_MMC2_CLKCTRL_OFT, 0, 2, 0x2);
> +	sr32(l3init_base + CM_L3INIT_MMC2_CLKCTRL_OFT, 24, 1, 0x1);
> +	sr32(l3init_base + CM_L3INIT_MMC2_CLKCTRL_OFT, 25, 1, 0x0);
> +
> +	/* WKUP clocks */
> +	sr32(wkup_base + CM_WKUPAON_GPIO1_CLKCTRL_OFT, 0, 32, 0x1);
> +	wait_on_value((1 << 17)|(1 << 16), 0, wkup_base + CM_WKUPAON_GPIO1_CLKCTRL_OFT, LDELAY);
> +	sr32(wkup_base + CM_WKUPAON_TIMER1_CLKCTRL_OFT, 0, 32, 0x01000002);
> +	wait_on_value((1 << 17)|(1 << 16), 0, wkup_base + CM_WKUPAON_TIMER1_CLKCTRL_OFT, LDELAY);
> +	sr32(wkup_base + CM_WKUPAON_KBD_CLKCTRL_OFT, 0, 32, 0x2);
> +	wait_on_value((1 << 17)|(1 << 16), 0, wkup_base + CM_WKUPAON_KBD_CLKCTRL_OFT, LDELAY);
> +
> +	sr32(CM_DMA_CLKSTCTRL, 0, 32, 0x0);
> +	sr32(CM_EMIF_CLKSTCTRL, 0, 32, 0x3);
> +	sr32(CM_EMIF_EMIF1_CLKCTRL, 0, 32, 0x1);
> +	wait_on_value((1 << 17)|(1 << 16), 0, CM_EMIF_EMIF1_CLKCTRL, LDELAY);
> +	sr32(CM_EMIF_EMIF2_CLKCTRL, 0, 32, 0x1);
> +	wait_on_value((1 << 17)|(1 << 16), 0, CM_EMIF_EMIF2_CLKCTRL, LDELAY);
> +	sr32(CM_C2C_CLKSTCTRL, 0, 32, 0x3);
> +	sr32(CM_L3MAIN2_GPMC_CLKCTRL, 0, 32, 0x1);
> +	wait_on_value((1 << 17)|(1 << 16), 0, CM_L3MAIN2_GPMC_CLKCTRL, LDELAY);
> +	sr32(CM_L3INSTR_L3_MAIN_3_CLKCTRL, 0, 32, 0x1);
> +	wait_on_value((1 << 17)|(1 << 16), 0, CM_L3INSTR_L3_MAIN_3_CLKCTRL, LDELAY);
> +	sr32(CM_L3INSTR_L3_INSTR_CLKCTRL, 0, 32, 0x1);
> +	wait_on_value((1 << 17)|(1 << 16), 0, CM_L3INSTR_L3_INSTR_CLKCTRL, LDELAY);
> +	sr32(CM_L3INSTR_OCP_WP_NOC_CLKCTRL, 0, 32, 0x1);
> +	wait_on_value((1 << 17)|(1 << 16), 0, CM_L3INSTR_OCP_WP_NOC_CLKCTRL, LDELAY);
> +
> +	/* WDT clocks */
> +	sr32(wkup_base + CM_WKUPAON_WD_TIMER2_CLKCTRL_OFT, 0, 32, 0x2);
> +	wait_on_value((1 << 17)|(1 << 16), 0, wkup_base + CM_WKUPAON_WD_TIMER2_CLKCTRL_OFT, LDELAY);
> +
> +	/* Enable Camera clocks */
> +	sr32(cam_base, 0, 32, 0x3);
> +	sr32(cam_base + CM_CAM_ISS_CLKCTRL_OFT, 0, 32, 0x102);
> +	sr32(cam_base + CM_CAM_FDIF_CLKCTRL_OFT, 0, 32, 0x2);
> +	sr32(cam_base, 0, 32, 0x0);
> +
> +	/* Enable DSS clocks */
> +	/* PM_DSS_PWRSTCTRL ON State and LogicState = 1 (Retention) */
> +	__raw_writel(7, PM_DSS_PWRSTCTRL); /* DSS_PRM */
> +
> +	sr32(dss_base, 0, 32, 0x2);
> +	sr32(dss_base + CM_DSS_DSS_CLKCTRL_OFT, 0, 32, 0xf02);
> +
> +	/* Check for DSS Clocks */
> +	while ((__raw_readl(dss_base) & 0xF00) != 0xE00)
> +	;
> +	/* Set HW_AUTO transition mode */
> +	sr32(dss_base, 0, 32, 0x3);
> +
> +	/* Enable GPU clocks */
> +	sr32(gpu_base, 0, 32, 0x2);
> +	sr32(gpu_base + CM_GPU_GPU_CLKCTRL_OFT, 0, 32, 0x2);
> +
> +	/* Enable hsi/unipro/usb/sata clocks */
> +	sr32(l3init_base + CM_L3INIT_HSI_CLKCTRL_OFT, 0, 32, 0x1);
> +	sr32(l3init_base + CM_L3INIT_UNIPRO2_CLKCTRL_OFT, 0, 32, 0x2);
> +	sr32(l3init_base + CM_L3INIT_USB_HOST_HS_CLKCTRL_OFT, 0, 32, 0x2);
> +	sr32(l3init_base + CM_L3INIT_USB_TLL_HS_CLKCTRL_OFT, 0, 32, 0x1);
> +	sr32(l3init_base + CM_L3INIT_IEEE1500_2_OCP_CLKCTRL_OFT, 0, 32, 0x2);
> +	sr32(l3init_base + CM_L3INIT_SATA_CLKCTRL_OFT, 0, 32, 0x2);
> +	sr32(l3init_base + CM_L3INIT_OCP2SCP1_CLKCTRL_OFT, 0, 32, 0x1);
> +	sr32(l3init_base + CM_L3INIT_OCP2SCP3_CLKCTRL_OFT, 0, 32, 0x1);
> +	sr32(l3init_base + CM_L3INIT_USB_OTG_SS_CLKCTRL_OFT, 0, 32, 0x1);
> +}
> diff --git a/arch/arm/mach-omap/omap5_generic.c b/arch/arm/mach-omap/omap5_generic.c
> new file mode 100644
> index 0000000..11bb068
> --- /dev/null
> +++ b/arch/arm/mach-omap/omap5_generic.c
> @@ -0,0 +1,509 @@
> +/*
> + * (C) Copyright 2013
> + * Sam Solutions, <sam-solutions.com>
> + *
> + * Authors:
> + *	Uladzimir Bely <u.bely@sam-solutions.com>
> + *	Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
> + *
> + * Derived from OMAP4 work
> + */
> +
> +#include <common.h>
> +#include <init.h>
> +#include <io.h>
> +#include <mach/clocks.h>
> +#include <mach/omap5-clock.h>
> +#include <mach/omap5-silicon.h>
> +#include <mach/omap5-mux.h>
> +#include <mach/syslib.h>
> +#include <mach/generic.h>
> +#include <mach/gpmc.h>
> +#include <mach/gpio.h>
> +
> +#define MIDR_CORTEX_A15_R0P0				0x410FC0F0
> +
> +#define CONTROL_ID_CODE					0x4A002204
> +
> +#define OMAP5430_CONTROL_ID_CODE_ES1_0			0x0B94202F
> +#define OMAP5432_CONTROL_ID_CODE_ES1_0			0x0B99802F
> +#define OMAP5430_CONTROL_ID_CODE_ES2_0			0x1B94202F
> +#define OMAP5432_CONTROL_ID_CODE_ES2_0			0x1B99802F
> +
> +/* EMIF_L3_CONFIG register value */
> +#define EMIF_L3_CONFIG_VAL_SYS_10_LL_0			0x0A0000FF
> +#define EMIF_L3_CONFIG_VAL_SYS_10_MPU_3_LL_0		0x0A300000
> +#define EMIF_L3_CONFIG_VAL_SYS_10_MPU_5_LL_0		0x0A500000
> +
> +void __noreturn reset_cpu(unsigned long addr)
> +{
> +	writel(PRM_RSTCTRL_RESET, PRM_RSTCTRL);
> +
> +	while (1);
> +}
> +
> +#define WATCHDOG_WSPR					0x48
> +#define WATCHDOG_WWPS					0x34
> +
> +static void wait_for_command_complete(void)
> +{
> +	int pending = 1;
> +
> +	do {
> +		pending = readl(OMAP54XX_WDT2_BASE + WATCHDOG_WWPS);
> +	} while (pending);
> +}
> +
> +/* EMIF */
> +#define EMIF_REVISION					0x0000
> +#define EMIF_STATUS					0x0004
> +#define EMIF_SDRAM_CONFIG				0x0008
> +#define EMIF_SDRAM_CONFIG_2				0x000C
> +#define EMIF_SDRAM_REFRESH_CONTROL			0x0010
> +#define EMIF_SDRAM_REFRESH_CONTROL_SHADOW		0x0014
> +#define EMIF_SDRAM_TIMING_1				0x0018
> +#define EMIF_SDRAM_TIMING_1_SHADOW			0x001C
> +#define EMIF_SDRAM_TIMING_2				0x0020
> +#define EMIF_SDRAM_TIMING_2_SHADOW			0x0024
> +#define EMIF_SDRAM_TIMING_3				0x0028
> +#define EMIF_SDRAM_TIMING_3_SHADOW			0x002C
> +#define EMIF_POWER_MANAGEMENT_CONTROL			0x0038
> +#define EMIF_POWER_MANAGEMENT_CONTROL_SHADOW		0x003C
> +#define EMIF_LPDDR2_MODE_REG_DATA			0x0040
> +#define EMIF_LPDDR2_MODE_REG_CONFIG			0x0050
> +#define EMIF_OCP_CONFIG					0x0054
> +#define EMIF_OCP_CFG_VALUE_1				0x0058
> +#define EMIF_OCP_CFG_VALUE_2				0x005C
> +#define EMIF_PERFORMANCE_COUNTER_1			0x0080
> +#define EMIF_PERFORMANCE_COUNTER_2			0x0084
> +#define EMIF_PERFORMANCE_COUNTER_CONFIG			0x0088
> +#define EMIF_PERFORMANCE_COUNTER_MASTER_REGION_SELECT	0x008C
> +#define EMIF_PERFORMANCE_COUNTER_TIME			0x0090
> +#define EMIF_MISC_REG					0x0094
> +#define EMIF_DLL_CALIB_CTRL				0x0098
> +#define EMIF_DLL_CALIB_CTRL_SHADOW			0x009c
> +
> +#define EMIF_PWR_MGMT_CTRL				0x0038
> +#define EMIF_PWR_MGMT_CTRL_SHADOW			0x003c
> +#define EMIF_READ_IDLECTRL				0x0098
> +#define EMIF_READ_IDLECTRL_SHADOW			0x009c
> +#define EMIF_ZQ_CONFIG					0x00c8
> +#define EMIF_TEMP_ALERT_CONFIG				0x00cc
> +#define EMIF_L3_CONFIG					0x0054
> +
> +#define NUMBER_OF_EMIF_EXT_CTRL_REGISTERS		30
> +
> +#define EMIF_SDRAM_OUTPUT_IMPEDANCE_CALIBRATION_CONFIG	0x00C8
> +
> +#define EMIF_DDR_PHY_CTRL_1				0x00e4
> +#define EMIF_DDR_PHY_CTRL_1_SHADOW			0x00e8
> +#define EMIF_DDR_PHY_CTRL_2				0x00eC
> +#define EMIF_DDR_EXT_PHY_CTRL_1				0x0200
> +
> +#define CS0						0
> +#define CS1						1
> +
> +#define DMM_LISA_MAP_0					0x0040
> +#define DMM_LISA_MAP_1					0x0044
> +#define DMM_LISA_MAP_2					0x0048
> +#define DMM_LISA_MAP_3					0x004C
> +
> +#define EMIF_REG_CS1NVMEN_MASK (1 << 30)
> +#define EMIF_REG_INITREF_DIS_MASK (1 << 31)
> +#define EMIF_REG_CS_SHIFT	31
> +#define EMIF_REG_REFRESH_EN_MASK			0x40000000
> +#define EMIF_REG_EBANK_MASK (1 << 3)
> +
> +#define MR0_ADDR					0
> +#define MR1_ADDR					1
> +#define MR2_ADDR					2
> +#define MR3_ADDR					3
> +#define MR4_ADDR					4
> +#define MR10_ADDR					10
> +#define MR16_ADDR					16
> +#define RL_FINAL					8
> +
> +#define MR16_REF_FULL_ARRAY				0
> +#define MR0_DAI_MASK					1
> +
> +#define REF_EN						0x40000000
> +
> +/* defines for MR1 */
> +#define MR1_BL4						2
> +#define MR1_BL8						3
> +#define MR1_BL16					4
> +
> +#define MR1_BT_SEQ					0
> +#define BT_INT						1
> +
> +#define MR1_WC						0
> +#define MR1_NWC						1
> +
> +#define MR1_NWR3					1
> +#define MR1_NWR4					2
> +#define MR1_NWR5					3
> +#define MR1_NWR6					4
> +#define MR1_NWR7					5
> +#define MR1_NWR8					6
> +
> +#define MR1_BL_8_BT_SEQ_WRAP_EN_NWR_8			0xc3
> +
> +/* defines for MR2 */
> +#define MR2_RL3_WL1					1
> +#define MR2_RL4_WL2					2
> +#define MR2_RL5_WL2					3
> +#define MR2_RL6_WL3					4
> +
> +/* defines for MR10 */
> +#define MR10_ZQINIT					0xFF
> +#define MR10_ZQRESET					0xC3
> +#define MR10_ZQCL					0xAB
> +#define MR10_ZQCS					0x56
> +
> +/* Elpida 2x2Gbit */
> +#define SDRAM_CONFIG_INIT				0x80800EB1
> +#define DDR_PHY_CTRL_1_INIT				0x849FFFF5
> +#define READ_IDLE_CTRL					0x000501FF
> +#define PWR_MGMT_CTRL					0x4000000f
> +#define PWR_MGMT_CTRL_OPP100				0x4000000f
> +#define ZQ_CONFIG					0x500b3215
> +
> +#define CS1_MR(mr)					((mr) | 0x80000000)
> +
> +/* CLKCTRL_IDLSET */
> +#define MODULE_CLKCTRL_IDLEST_TRANSITIONING		1
> +#define MODULE_CLKCTRL_IDLEST_DISABLED			3
> +#define MODULE_CLKCTRL_IDLEST_SHIFT			16
> +#define MODULE_CLKCTRL_IDLEST_MASK			(3 << 16)
> +
> +
> +int omap5_emif_config(u32 base, const struct omap5_ddr_regs *regs)
> +{
> +	u32 *ext_phy_ctrl_base;
> +	u32 *emif_ext_phy_ctrl_base;
> +	int i;
> +
> +	/* Not NVM */
> +	sr32(base + EMIF_SDRAM_CONFIG_2, 30, 1, 0);
> +
> +	/*
> +	 * Keep REG_INITREF_DIS = 1 to prevent re-initialization of SDRAM
> +	 * when EMIF_SDRAM_CONFIG register is written
> +	 */
> +	sr32(base + EMIF_SDRAM_REFRESH_CONTROL, 31, 1, 1);
> +
> +	/*
> +	 * Set the SDRAM_CONFIG and PHY_CTRL for the
> +	 * un-locked frequency & default RL
> +	 */
> +	writel(regs->sdram_config_init, base + EMIF_SDRAM_CONFIG);
> +	writel(regs->emif_ddr_phy_ctlr_1_init, base + EMIF_DDR_PHY_CTRL_1);
> +
> +	ext_phy_ctrl_base = (u32 *) &(regs->emif_ddr_ext_phy_ctrl_1_init);
> +	emif_ext_phy_ctrl_base = (u32 *) (base + EMIF_DDR_EXT_PHY_CTRL_1);
> +
> +	/* Configure external phy control registers */
> +	for (i = 0; i < NUMBER_OF_EMIF_EXT_CTRL_REGISTERS; i++) {
> +		writel(*ext_phy_ctrl_base++, emif_ext_phy_ctrl_base++);
> +		/* Write the shadow register here as well */
> +		writel(*ext_phy_ctrl_base++, emif_ext_phy_ctrl_base++);
> +	}
> +
> +	writel(MR0_ADDR, base + EMIF_LPDDR2_MODE_REG_CONFIG);
> +	writel(CS1_MR(MR0_ADDR), base + EMIF_LPDDR2_MODE_REG_CONFIG);
> +	while (readl(base + EMIF_LPDDR2_MODE_REG_DATA) & MR0_DAI_MASK);
> +
> +	writel(MR10_ADDR, base + EMIF_LPDDR2_MODE_REG_CONFIG);
> +	writel(MR10_ZQINIT, base + EMIF_LPDDR2_MODE_REG_DATA);
> +	writel(CS1_MR(MR10_ADDR), base + EMIF_LPDDR2_MODE_REG_CONFIG);
> +	writel(MR10_ZQINIT, base + EMIF_LPDDR2_MODE_REG_DATA);
> +
> +	/*
> +	 * tZQINIT = 1 us
> +	 * Enough loops assuming a maximum of 2GHz
> +	 */
> +	sdelay(2000);
> +
> +	writel(MR1_ADDR, base + EMIF_LPDDR2_MODE_REG_CONFIG);
> +	writel(MR1_BL_8_BT_SEQ_WRAP_EN_NWR_8, base + EMIF_LPDDR2_MODE_REG_DATA);
> +	writel(CS1_MR(MR1_ADDR), base + EMIF_LPDDR2_MODE_REG_CONFIG);
> +	writel(MR1_BL_8_BT_SEQ_WRAP_EN_NWR_8, base + EMIF_LPDDR2_MODE_REG_DATA);
> +
> +	writel(MR16_ADDR, base + EMIF_LPDDR2_MODE_REG_CONFIG);
> +	writel(MR16_REF_FULL_ARRAY, base + EMIF_LPDDR2_MODE_REG_DATA);
> +	writel(CS1_MR(MR16_ADDR), base + EMIF_LPDDR2_MODE_REG_CONFIG);
> +	writel(MR16_REF_FULL_ARRAY, base + EMIF_LPDDR2_MODE_REG_DATA);
> +
> +	/*
> +	 * Enable refresh along with writing MR2
> +	 * Encoding of RL in MR2 is (RL - 2)
> +	 */
> +	writel(MR2_ADDR | EMIF_REG_REFRESH_EN_MASK, base + EMIF_LPDDR2_MODE_REG_CONFIG);
> +	writel(RL_FINAL - 2, base + EMIF_LPDDR2_MODE_REG_DATA);
> +	writel(CS1_MR(MR2_ADDR) | EMIF_REG_REFRESH_EN_MASK, base + EMIF_LPDDR2_MODE_REG_CONFIG);
> +	writel(RL_FINAL - 2, base + EMIF_LPDDR2_MODE_REG_DATA);
> +
> +	writel(MR3_ADDR, base + EMIF_LPDDR2_MODE_REG_CONFIG);
> +	writel(0x1, base + EMIF_LPDDR2_MODE_REG_DATA);
> +	writel(CS1_MR(MR3_ADDR), base + EMIF_LPDDR2_MODE_REG_CONFIG);
> +	writel(0x1, base + EMIF_LPDDR2_MODE_REG_DATA);
> +
> +
> +	writel(regs->sdram_config, base + EMIF_SDRAM_CONFIG);
> +	writel(regs->emif_ddr_phy_ctlr_1, base + EMIF_DDR_PHY_CTRL_1);
> +
> +	/* Enable refresh now */
> +	sr32(base + EMIF_SDRAM_REFRESH_CONTROL, 31, 1, 0);
> +
> +	/* Emif_update_timings */
> +	writel(regs->ref_ctrl, base + EMIF_SDRAM_REFRESH_CONTROL_SHADOW);
> +	writel(regs->sdram_tim1, base + EMIF_SDRAM_TIMING_1_SHADOW);
> +	writel(regs->sdram_tim2, base + EMIF_SDRAM_TIMING_2_SHADOW);
> +	writel(regs->sdram_tim3, base + EMIF_SDRAM_TIMING_3_SHADOW);
> +
> +	writel(0xF0F0, base + EMIF_PWR_MGMT_CTRL);
> +	writel(0xF0F0, base + EMIF_PWR_MGMT_CTRL_SHADOW);
> +	writel(regs->read_idle_ctrl, base + EMIF_READ_IDLECTRL_SHADOW);
> +	writel(regs->zq_config, base + EMIF_ZQ_CONFIG);
> +	writel(regs->temp_alert_config, base + EMIF_TEMP_ALERT_CONFIG);
> +	writel(regs->emif_ddr_phy_ctlr_1, base + EMIF_DDR_PHY_CTRL_1_SHADOW);
> +
> +	writel(EMIF_L3_CONFIG_VAL_SYS_10_MPU_5_LL_0, base + EMIF_L3_CONFIG);
> +	
> +	return 0;
> +}
> +
> +static inline void wait_for_clk_enable(u32 *clkctrl_addr)
> +{
> +	u32 clkctrl, idlest = MODULE_CLKCTRL_IDLEST_DISABLED;
> +	u32 bound = LDELAY;
> +
> +	while ((idlest == MODULE_CLKCTRL_IDLEST_DISABLED) ||
> +		(idlest == MODULE_CLKCTRL_IDLEST_TRANSITIONING)) {
> +
> +		clkctrl = readl(clkctrl_addr);
> +		idlest = (clkctrl & MODULE_CLKCTRL_IDLEST_MASK) >>
> +			 MODULE_CLKCTRL_IDLEST_SHIFT;
> +		if (--bound == 0) {
> +			debug("Clock enable failed for 0x%p idlest 0x%x\n",
> +				clkctrl_addr, clkctrl);
> +			return;
> +		}
> +	}
> +}
> +
> +static unsigned int cortex_a15_rev(void)
> +{
> +	unsigned int rev;
> +
> +	/* Read Main ID Register (MIDR) */
> +	asm ("mrc p15, 0, %0, c0, c0, 0" : "=r" (rev));
> +
> +	return rev;
> +}
> +
> +unsigned int omap5_revision(void)
> +{
> +	unsigned int rev = cortex_a15_rev();
> +
> +	switch(rev) {
> +	case MIDR_CORTEX_A15_R0P0:
> +		switch(readl(CONTROL_ID_CODE)) {
> +		case OMAP5430_CONTROL_ID_CODE_ES1_0:
> +			return OMAP5430_ES1_0;
> +			break;
> +		case OMAP5430_CONTROL_ID_CODE_ES2_0:
> +			return OMAP5430_ES2_0;
> +			break;
> +		case OMAP5432_CONTROL_ID_CODE_ES1_0:
> +			return OMAP5432_ES1_0;
> +			break;
> +		case OMAP5432_CONTROL_ID_CODE_ES2_0:
> +			return OMAP5432_ES2_0;
> +			break;
> +		default:
> +			return OMAP5430_ES1_0;
> +			break;
> +		}
> +	default:
> +		return OMAP543X_SILICON_ID_INVALID;
> +		break;
> +	}
> +}
> +
> +void omap5_ddr_init(const struct omap5_ddr_regs *ddr_regs, const struct dpll_param *core)
> +{
> +	/* DMM Configuration */
> +	writel(0xFF020100, OMAP54XX_DMM_BASE + DMM_LISA_MAP_3);
> +	writel(0x80740300, OMAP54XX_DMM_BASE + DMM_LISA_MAP_2);
> +	writel(0x0, OMAP54XX_DMM_BASE + DMM_LISA_MAP_1);
> +	writel(0x0, OMAP54XX_DMM_BASE + DMM_LISA_MAP_0);
> +
> +	writel(0xFF020100, OMAP54XX_MA_BASE + DMM_LISA_MAP_3);
> +	writel(0x80740300, OMAP54XX_MA_BASE + DMM_LISA_MAP_2);
> +	writel(0x0, OMAP54XX_MA_BASE + DMM_LISA_MAP_1);
> +	writel(0x0, OMAP54XX_MA_BASE + DMM_LISA_MAP_0);
> +
> +	/*
> +	 * DDR needs to be initialised @ 19.2 MHz
> +	 * So put core DPLL in bypass mode
> +	 * Configure the Core DPLL but don't lock it
> +	 */
> +	omap5_configure_core_dpll_no_lock(core);
> +
> +	omap5_emif_config(OMAP54XX_EMIF1_BASE, ddr_regs);
> +	omap5_emif_config(OMAP54XX_EMIF2_BASE, ddr_regs);
> +
> +	/* Put EMIF clock domain in sw wakeup mode */
> +	sr32(CM_EMIF_CLKSTCTRL, 0, 2, 2);
> +
> +	wait_for_clk_enable((u32*)CM_EMIF_EMIF1_CLKCTRL);
> +	wait_for_clk_enable((u32*)CM_EMIF_EMIF2_CLKCTRL);
> +
> +	writel(0x00001709, CM_SHADOW_FREQ_CONFIG1);
> +
> +	if (!wait_on_value(1, 0, CM_SHADOW_FREQ_CONFIG1, LDELAY)) {
> +		debug("FREQ UPDATE procedure failed!!");
> +		hang();
> +	}
> +}
> +
> +void omap5_power_i2c_send(u32 r)
> +{
> +	u32 val;
> +
> +	writel(r, OMAP54XX_PRM_VC_VAL_BYPASS);
> +
> +	val = readl(OMAP54XX_PRM_VC_VAL_BYPASS);
> +	val |= 0x1000000;
> +	writel(val, OMAP54XX_PRM_VC_VAL_BYPASS);
> +
> +	while (readl(OMAP54XX_PRM_VC_VAL_BYPASS) & 0x1000000)
> +		;
> +
> +	val = readl(OMAP54XX_PRM_IRQSTATUS_MPU);
> +	writel(val, OMAP54XX_PRM_IRQSTATUS_MPU);
> +}
> +
> +/* Shutdown watchdog */
> +static int watchdog_init(void)
> +{
> +	void __iomem *wd2_base = (void *)OMAP54XX_WDT2_BASE;
> +
> +	writel(WD_UNLOCK1, wd2_base + WATCHDOG_WSPR);
> +	wait_for_command_complete();
> +	writel(WD_UNLOCK2, wd2_base + WATCHDOG_WSPR);
> +
> +	return 0;
> +}
> +late_initcall(watchdog_init);
> +
> +static int omap_vector_init(void)
> +{
> +	/*
> +	 * omap4 usbboot interfaces with the omap4 ROM to reuse the USB port
> +	 * used for booting.
> +	 * The ROM code uses interrupts for the transfers, so do not modify the
> +	 * interrupt vectors in this case.
> +	 */
> +	if (omap5_bootsrc() != OMAP_BOOTSRC_USB1) {
> +		__asm__ __volatile__ (
> +			"mov    r0, #0;"
> +			"mcr    p15, #0, r0, c12, c0, #0;"
> +			:
> +			:
> +			: "r0"
> +		);
> +	}
> +
> +	return 0;
> +}
> +core_initcall(omap_vector_init);
> +
> +#define OMAP5_TRACING_VECTOR3 0x4031f048
> +
> +enum omap_boot_src omap5_bootsrc(void)
> +{
> +	u32 bootsrc = readl(OMAP5_TRACING_VECTOR3);
> +
> +	if (bootsrc & (1 << 5))
> +		return OMAP_BOOTSRC_MMC1;
> +	if (bootsrc & (1 << 3))
> +		return OMAP_BOOTSRC_NAND;
> +	if (bootsrc & (1<<21))
> +		return OMAP_BOOTSRC_USB1;
> +	return OMAP_BOOTSRC_UNKNOWN;
> +}
> +
> +/* Scaling vcore functions are taken from u-boot */
> +void do_scale_vcore(u32 vcore_reg, u32 volt_mv)
> +{
> +	u32 temp, offset_code;
> +	u32 step = 10000; /* 10 mV represented in uV */;
> +
> +	offset_code = (volt_mv * 1000 - SMPS_BASE_VOLT_UV + step - 1) / step + 6;
> +
> +	temp = SMPS_I2C_SLAVE_ADDR |
> +		(vcore_reg << OMAP54XX_PRM_VC_VAL_BYPASS_REGADDR_SHIFT) |
> +		(offset_code << OMAP54XX_PRM_VC_VAL_BYPASS_DATA_SHIFT) |
> +		OMAP54XX_PRM_VC_VAL_BYPASS_VALID_BIT;
> +	writel(temp, OMAP54XX_PRM_VC_VAL_BYPASS);
> +	if (!wait_on_value(OMAP54XX_PRM_VC_VAL_BYPASS_VALID_BIT, 0,
> +		OMAP54XX_PRM_VC_VAL_BYPASS, LDELAY)) {
> +		debug("Scaling voltage failed for 0x%x\n", vcore_reg);
> +	}
> +}
> +
> +void omap5_scale_vcores(void)
> +{
> +	writel(0x150e, OMAP54XX_PRM_VC_CFG_I2C_CLK);
> +	writel(0, OMAP54XX_PRM_VC_CFG_I2C_MODE);
> +
> +	/* Palmas settings */
> +	do_scale_vcore(SMPS_REG_ADDR_12_MPU, VDD_MPU);
> +	do_scale_vcore(SMPS_REG_ADDR_45_IVA, VDD_MM);
> +	do_scale_vcore(SMPS_REG_ADDR_8_CORE, VDD_CORE);
> +}
> +
> +void omap5_do_set_mux(u32 base, struct pad_conf_entry const *array, int size)
> +{
> +	int i;
> +	struct pad_conf_entry *pad = (struct pad_conf_entry *) array;
> +
> +	for (i = 0; i < size; i++, pad++)
> +		writew(pad->val, base + pad->offset);
> +}
> +
> +/* GPMC timing for OMAP4 nand device */
> +const struct gpmc_config omap5_nand_cfg = {
> +	.cfg = {
> +		0x00000800,	/* CONF1 */
> +		0x00050500,	/* CONF2 */
> +		0x00040400,	/* CONF3 */
> +		0x03000300,	/* CONF4 */
> +		0x00050808,	/* CONF5 */
> +		0x00000000,	/* CONF6 */
> +	},
> +	/* GPMC address map as small as possible */
> +	.base = 0x28000000,
> +	.size = GPMC_SIZE_16M,
> +};
> +
> +static int omap5_gpio_init(void)
> +{
> +	add_generic_device("omap-gpio", 0, NULL, OMAP54XX_GPIO1_BASE,
> +				0xf00, IORESOURCE_MEM, NULL);
> +	add_generic_device("omap-gpio", 1, NULL, OMAP54XX_GPIO2_BASE,
> +				0xf00, IORESOURCE_MEM, NULL);
> +	add_generic_device("omap-gpio", 2, NULL, OMAP54XX_GPIO3_BASE,
> +				0xf00, IORESOURCE_MEM, NULL);
> +	add_generic_device("omap-gpio", 3, NULL, OMAP54XX_GPIO4_BASE,
> +				0xf00, IORESOURCE_MEM, NULL);
> +	add_generic_device("omap-gpio", 4, NULL, OMAP54XX_GPIO5_BASE,
> +				0xf00, IORESOURCE_MEM, NULL);
> +	add_generic_device("omap-gpio", 5, NULL, OMAP54XX_GPIO6_BASE,
> +				0xf00, IORESOURCE_MEM, NULL);
> +
> +	return 0;
> +}
> +coredevice_initcall(omap5_gpio_init);
> diff --git a/arch/arm/mach-omap/omap_generic.c b/arch/arm/mach-omap/omap_generic.c
> index 580ed3e..ca3e553 100644
> --- a/arch/arm/mach-omap/omap_generic.c
> +++ b/arch/arm/mach-omap/omap_generic.c
> @@ -26,6 +26,8 @@ enum omap_boot_src omap_bootsrc(void)
>  	return omap3_bootsrc();
>  #elif defined(CONFIG_ARCH_OMAP4)
>  	return omap4_bootsrc();
> +#elif defined(CONFIG_ARCH_OMAP5)
> +	return omap5_bootsrc();
>  #elif defined(CONFIG_ARCH_AM33XX)
>  	return am33xx_bootsrc();
>  #endif
> diff --git a/arch/arm/mach-omap/s32k_clksource.c b/arch/arm/mach-omap/s32k_clksource.c
> index 7def8b1..0377e0d 100644
> --- a/arch/arm/mach-omap/s32k_clksource.c
> +++ b/arch/arm/mach-omap/s32k_clksource.c
> @@ -27,13 +27,18 @@
>  #include <io.h>
>  #include <mach/omap3-silicon.h>
>  #include <mach/omap4-silicon.h>
> +#include <mach/omap5-silicon.h>
>  #include <mach/clocks.h>
>  #include <mach/timers.h>
>  #include <mach/sys_info.h>
>  #include <mach/syslib.h>
>  
>  /** Sync 32Khz Timer registers */
> +#ifdef CONFIG_ARCH_OMAP5
> +#define S32K_CR			0x30
> +#else
>  #define S32K_CR			0x10
> +#endif
>  #define S32K_FREQUENCY		32768
>  
>  static void __iomem *timerbase;
> @@ -73,6 +78,8 @@ static int s32k_clocksource_init(void)
>  		timerbase = (void *)OMAP3_32KTIMER_BASE;
>  	else if (IS_ENABLED(CONFIG_ARCH_OMAP4))
>  		timerbase = (void *)OMAP44XX_32KTIMER_BASE;
> +	else if (IS_ENABLED(CONFIG_ARCH_OMAP5))
> +		timerbase = (void *)OMAP54XX_32KTIMER_BASE;
>  	else
>  		BUG();
>  
> diff --git a/drivers/mci/Kconfig b/drivers/mci/Kconfig
> index 9558f28..5aee417 100644
> --- a/drivers/mci/Kconfig
> +++ b/drivers/mci/Kconfig
> @@ -67,7 +67,7 @@ config MCI_IMX_ESDHC_PIO
>  
>  config MCI_OMAP_HSMMC
>  	bool "OMAP HSMMC"
> -	depends on ARCH_OMAP4 || ARCH_OMAP3 || ARCH_AM33XX
> +	depends on ARCH_OMAP5 || ARCH_OMAP4 || ARCH_OMAP3 || ARCH_AM33XX
>  	help
>  	  Enable this entry to add support to read and write SD cards on
>  	  both OMAP3 and OMAP4 based systems.
> diff --git a/drivers/mci/omap_hsmmc.c b/drivers/mci/omap_hsmmc.c
> index b379c31..e923dc1 100644
> --- a/drivers/mci/omap_hsmmc.c
> +++ b/drivers/mci/omap_hsmmc.c
> @@ -71,6 +71,10 @@ static struct omap_mmc_driver_data omap4_data = {
>  	.reg_ofs = 0x100,
>  };
>  
> +static struct omap_mmc_driver_data omap5_data = {
> +	.reg_ofs = 0x100,
> +};
> +
>  /*
>   * OMAP HS MMC Bit definitions
>   */
> @@ -621,6 +625,9 @@ static struct platform_device_id omap_mmc_ids[] = {
>  		.name = "omap4-hsmmc",
>  		.driver_data = (unsigned long)&omap4_data,
>  	}, {
> +		.name = "omap5-hsmmc",
> +		.driver_data = (unsigned long)&omap5_data,
> +	}, {
>  		/* sentinel */
>  	},
>  };
> -- 
> 1.8.1.5
> 
> 
> _______________________________________________
> barebox mailing list
> barebox@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

  reply	other threads:[~2013-04-25 11:10 UTC|newest]

Thread overview: 13+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
     [not found] <014261>
2013-04-24 10:33 ` Uladzimir Bely
2013-04-24 10:51   ` Uladzimir Bely
2013-04-24 20:11   ` Sascha Hauer
2013-04-25  9:09     ` Uladzimir Bely
2013-04-25 11:05       ` Jean-Christophe PLAGNIOL-VILLARD [this message]
2013-04-25 11:58       ` Jan Lübbe
2013-04-25 12:42         ` Uladzimir Bely
2013-04-25 20:47           ` Sascha Hauer
2013-04-26  8:31           ` Jan Lübbe
     [not found]         ` <517A57F8.8020805@sam-solutions.net>
2013-04-26 10:54           ` Jan Lübbe
2013-04-26 10:59             ` Uladzimir Bely
2013-04-26 21:58               ` Sascha Hauer
2013-04-25 13:31       ` menon.nishanth

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20130425110521.GG13393@game.jcrosoft.org \
    --to=plagnioj@jcrosoft.com \
    --cc=barebox@lists.infradead.org \
    --cc=u.bely@sam-solutions.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox