mail archive of the barebox mailing list
 help / color / mirror / Atom feed
From: Sascha Hauer <s.hauer@pengutronix.de>
To: Alexander Kurz <akurz@blala.de>
Cc: barebox@lists.infradead.org
Subject: Re: [PATCH] ARM i.MX35: Add support for the Amazon Kindle3
Date: Mon, 11 Jul 2016 07:51:59 +0200	[thread overview]
Message-ID: <20160711055159.GV20657@pengutronix.de> (raw)
In-Reply-To: <1468069784-31672-1-git-send-email-akurz@blala.de>

On Sat, Jul 09, 2016 at 03:09:44PM +0200, Alexander Kurz wrote:
> The Amazon Model No. D00901 Kindle3 is an E-Book reader based on the
> i.MX35 SOC. The device boots in internal boot mode from a build-in eMMC,
> alternatively the device may be set into USB-downloader mode when the
> Vol+ key is pressed on startup.
> 
> Add support for this device and make barebox a drop-in replacement for
> the factory shipped u-boot image.
> Constraints for the use as drop-in replacement:
> - imximg header (offset 0x400) has a maximum size of 2kB minus 16 byte
>   since the last 16 bytes are used to store a vendor specific hardware
>   desctription identifier
> - the bootloader space (application plus env) is limited to 256kB minus
>   16 bytes when installed with offset of 4kB (the u-boot offset was 3kB).
>   A vendor specific device identifier is stored in the gap between
>   application and kernel. The vendor specific identifiers should not
>   be overwritten.
> 
> Notable features:
> - Support for eMMC, USB, UART, I2C, SPI and Keys (except keyboard)
> - Full support for vendor specific ATAGs
> - usbserial barebox console access by pressing Select button at startup,
>   alternatively full console support on connector J14.
> 
> Signed-off-by: Alexander Kurz <akurz@blala.de>

Applied, thanks

Sascha

> ---
>  Documentation/boards/imx/amazon-kindle3.rst        |  28 ++
>  arch/arm/Makefile                                  |   1 +
>  arch/arm/boards/Makefile                           |   1 +
>  arch/arm/boards/kindle3/Makefile                   |   2 +
>  arch/arm/boards/kindle3/env/boot/mmc_kernel        |   7 +
>  arch/arm/boards/kindle3/env/init/serials           |  21 ++
>  arch/arm/boards/kindle3/env/init/usbconsole        |   8 +
>  arch/arm/boards/kindle3/env/nv/autoboot_timeout    |   1 +
>  arch/arm/boards/kindle3/env/nv/boot.default        |   1 +
>  arch/arm/boards/kindle3/env/nv/linux.bootargs.base |   1 +
>  .../boards/kindle3/env/nv/linux.bootargs.console   |   1 +
>  arch/arm/boards/kindle3/env/nv/linux.bootargs.lpj  |   1 +
>  arch/arm/boards/kindle3/flash-header.imxcfg        |  24 ++
>  arch/arm/boards/kindle3/kindle3.c                  | 318 +++++++++++++++++++++
>  arch/arm/boards/kindle3/lowlevel.c                 | 142 +++++++++
>  arch/arm/configs/kindle3_defconfig                 |  65 +++++
>  arch/arm/mach-imx/Kconfig                          |   9 +
>  17 files changed, 631 insertions(+)
>  create mode 100644 Documentation/boards/imx/amazon-kindle3.rst
>  create mode 100644 arch/arm/boards/kindle3/Makefile
>  create mode 100644 arch/arm/boards/kindle3/env/boot/mmc_kernel
>  create mode 100644 arch/arm/boards/kindle3/env/init/serials
>  create mode 100644 arch/arm/boards/kindle3/env/init/usbconsole
>  create mode 100644 arch/arm/boards/kindle3/env/nv/autoboot_timeout
>  create mode 100644 arch/arm/boards/kindle3/env/nv/boot.default
>  create mode 100644 arch/arm/boards/kindle3/env/nv/linux.bootargs.base
>  create mode 100644 arch/arm/boards/kindle3/env/nv/linux.bootargs.console
>  create mode 100644 arch/arm/boards/kindle3/env/nv/linux.bootargs.lpj
>  create mode 100644 arch/arm/boards/kindle3/flash-header.imxcfg
>  create mode 100644 arch/arm/boards/kindle3/kindle3.c
>  create mode 100644 arch/arm/boards/kindle3/lowlevel.c
>  create mode 100644 arch/arm/configs/kindle3_defconfig
> 
> diff --git a/Documentation/boards/imx/amazon-kindle3.rst b/Documentation/boards/imx/amazon-kindle3.rst
> new file mode 100644
> index 0000000..50592f2
> --- /dev/null
> +++ b/Documentation/boards/imx/amazon-kindle3.rst
> @@ -0,0 +1,28 @@
> +Amazon Kindle 3 "Kindle Keyboard" Model No. D00901
> +==================================================
> +
> +This e-book reader is based on a Freescale i.MX35 SOC.
> +The device is equiped with:
> +
> +* 256MiB synchronous dynamic RAM
> +* 4GiB eMMC
> +* a MC13892 PMIC
> +
> +The device boots in internal boot mode from eMMC and is shipped with a
> +vendor modified u-boot imximage.
> +
> +To upload and run a new bootloader the device can be put into USB-downloader
> +mode by the SOC microcode when Vol+ is pressed during startup. A new USB
> +device "SE Blank RINGO" should appear, barebox may be uploaded using
> +$ scripts/imx/imx-usb-loader barebox.imximg
> +
> +Note: a USB serial ACM console will be launched by a barebox init script
> +when the cursor select key is pressed during startup (e.g. before running
> +imx-usb-loader)
> +
> +Barebox may be used as drop-in replacement for the shipped bootloader.
> +When installing the barebox imximg on the eMMC take care not to overwrite
> +the partition table and vendor supplied serial numbers stored on the eMMC.
> +e.g. just write the imx-header and the application section:
> +memcpy -b -s barebox.imximg -d /dev/disk0.imx_header 1024 0 1024
> +memcpy -b -s barebox.imximg -d /dev/disk0.self 4096 0 195584
> diff --git a/arch/arm/Makefile b/arch/arm/Makefile
> index 865de04..9fc3cd3 100644
> --- a/arch/arm/Makefile
> +++ b/arch/arm/Makefile
> @@ -252,6 +252,7 @@ imxcfg-$(CONFIG_MACH_FREESCALE_MX35_3STACK) += $(boarddir)/freescale-mx35-3ds/fl
>  imxcfg-$(CONFIG_MACH_TQMA53) += $(boarddir)/tqma53/flash-header.imxcfg
>  imxcfg-$(CONFIG_MACH_EUKREA_CPUIMX25) += $(boarddir)/eukrea_cpuimx25/flash-header.imxcfg
>  imxcfg-$(CONFIG_MACH_EUKREA_CPUIMX35) += $(boarddir)/eukrea_cpuimx35/flash-header.imxcfg
> +imxcfg-$(CONFIG_MACH_KINDLE3) += $(boarddir)/kindle3/flash-header.imxcfg
>  imxcfg-$(CONFIG_TX53_REV_1011) += $(boarddir)/karo-tx53/flash-header-tx53-rev1011.imxcfg
>  imxcfg-$(CONFIG_TX53_REV_XX30) += $(boarddir)/karo-tx53/flash-header-tx53-revxx30.imxcfg
>  ifneq ($(imxcfg-y),)
> diff --git a/arch/arm/boards/Makefile b/arch/arm/boards/Makefile
> index c271f5d..e3dcc6a 100644
> --- a/arch/arm/boards/Makefile
> +++ b/arch/arm/boards/Makefile
> @@ -59,6 +59,7 @@ obj-$(CONFIG_MACH_HIGHBANK)			+= highbank/
>  obj-$(CONFIG_MACH_IMX21ADS)			+= freescale-mx21-ads/
>  obj-$(CONFIG_MACH_IMX233_OLINUXINO)		+= imx233-olinuxino/
>  obj-$(CONFIG_MACH_IMX27ADS)			+= freescale-mx27-ads/
> +obj-$(CONFIG_MACH_KINDLE3)			+= kindle3/
>  obj-$(CONFIG_MACH_LENOVO_IX4_300D)		+= lenovo-ix4-300d/
>  obj-$(CONFIG_MACH_LUBBOCK)			+= lubbock/
>  obj-$(CONFIG_MACH_MAINSTONE)			+= mainstone/
> diff --git a/arch/arm/boards/kindle3/Makefile b/arch/arm/boards/kindle3/Makefile
> new file mode 100644
> index 0000000..86c7462
> --- /dev/null
> +++ b/arch/arm/boards/kindle3/Makefile
> @@ -0,0 +1,2 @@
> +obj-y += kindle3.o
> +lwl-y += lowlevel.o
> diff --git a/arch/arm/boards/kindle3/env/boot/mmc_kernel b/arch/arm/boards/kindle3/env/boot/mmc_kernel
> new file mode 100644
> index 0000000..c6145b8
> --- /dev/null
> +++ b/arch/arm/boards/kindle3/env/boot/mmc_kernel
> @@ -0,0 +1,7 @@
> +#!/bin/sh
> +# Boot the Amazon factory-shipped kernel uimage stored on
> +# the eMMC at MOVINAND_OFFSET_KERNEL=266240.
> +
> +global linux.bootargs.dyn.root="root=/dev/mmcblk0p1 ro"
> +
> +bootm -c -a 0x80008000 /dev/disk0.kernel
> diff --git a/arch/arm/boards/kindle3/env/init/serials b/arch/arm/boards/kindle3/env/init/serials
> new file mode 100644
> index 0000000..76580ae
> --- /dev/null
> +++ b/arch/arm/boards/kindle3/env/init/serials
> @@ -0,0 +1,21 @@
> +#!/bin/sh
> +
> +global board.serial16
> +global board.revision16
> +
> +# 16-byte alphanumeric containing the serial number
> +# SN is the first 16 bytes before the bootloader
> +if test -b /dev/disk0.serial; then
> +	if memcpy -s /dev/disk0.serial -d tmp_serial16 -b 0 0 16; then
> +		readf tmp_serial16 global.board.serial16
> +	fi
> +fi
> +[ -f tmp_serial16 ] && rm tmp_serial16
> +
> +# 16-byte alphanumeric containing the board revision
> +if test -b /dev/disk0.imx_header; then
> +	if memcpy -s /dev/disk0.imx_header -d tmp_revision16 -b 2032 0 16; then
> +		readf tmp_revision16 global.board.revision16
> +	fi
> +fi
> +[ -f tmp_revision16 ] && rm tmp_revision16
> diff --git a/arch/arm/boards/kindle3/env/init/usbconsole b/arch/arm/boards/kindle3/env/init/usbconsole
> new file mode 100644
> index 0000000..87a8f9b
> --- /dev/null
> +++ b/arch/arm/boards/kindle3/env/init/usbconsole
> @@ -0,0 +1,8 @@
> +#!/bin/sh
> +
> +# Fiveway device select key activates usbserial access for 60s
> +echo
> +if gpio_get_value 63; then
> +	usbserial
> +	global.autoboot_timeout=60
> +fi
> diff --git a/arch/arm/boards/kindle3/env/nv/autoboot_timeout b/arch/arm/boards/kindle3/env/nv/autoboot_timeout
> new file mode 100644
> index 0000000..00750ed
> --- /dev/null
> +++ b/arch/arm/boards/kindle3/env/nv/autoboot_timeout
> @@ -0,0 +1 @@
> +3
> diff --git a/arch/arm/boards/kindle3/env/nv/boot.default b/arch/arm/boards/kindle3/env/nv/boot.default
> new file mode 100644
> index 0000000..3118b7a
> --- /dev/null
> +++ b/arch/arm/boards/kindle3/env/nv/boot.default
> @@ -0,0 +1 @@
> +mmc_kernel
> diff --git a/arch/arm/boards/kindle3/env/nv/linux.bootargs.base b/arch/arm/boards/kindle3/env/nv/linux.bootargs.base
> new file mode 100644
> index 0000000..3a940d8
> --- /dev/null
> +++ b/arch/arm/boards/kindle3/env/nv/linux.bootargs.base
> @@ -0,0 +1 @@
> +mem=256M ip=none
> diff --git a/arch/arm/boards/kindle3/env/nv/linux.bootargs.console b/arch/arm/boards/kindle3/env/nv/linux.bootargs.console
> new file mode 100644
> index 0000000..d775310
> --- /dev/null
> +++ b/arch/arm/boards/kindle3/env/nv/linux.bootargs.console
> @@ -0,0 +1 @@
> +console=ttymxc0,115200
> diff --git a/arch/arm/boards/kindle3/env/nv/linux.bootargs.lpj b/arch/arm/boards/kindle3/env/nv/linux.bootargs.lpj
> new file mode 100644
> index 0000000..aa3ba59
> --- /dev/null
> +++ b/arch/arm/boards/kindle3/env/nv/linux.bootargs.lpj
> @@ -0,0 +1 @@
> +lpj=2555904
> diff --git a/arch/arm/boards/kindle3/flash-header.imxcfg b/arch/arm/boards/kindle3/flash-header.imxcfg
> new file mode 100644
> index 0000000..cb56acf
> --- /dev/null
> +++ b/arch/arm/boards/kindle3/flash-header.imxcfg
> @@ -0,0 +1,24 @@
> +soc imx35
> +loadaddr 0x87eff400
> +dcdofs 0x400
> +
> +wm 32 0x53f80004 0x00821000
> +wm 32 0x53f80004 0x00821000
> +wm 32 0xb8001010 0x00000002
> +wm 32 0xb8001010 0x00000004
> +wm 32 0xb8001004 0x0019672f
> +wm 32 0xb8001000 0x93100000
> +wm 8 0x80000400 0xda
> +wm 32 0xb8001000 0xa3100000
> +wm 32 0x80000000 0x12344321
> +wm 32 0x80000000 0x12344321
> +wm 32 0xb8001000 0xb3100000
> +wm 8 0x80000033 0xda
> +wm 8 0x82000000 0xff
> +wm 32 0xb8001000 0x83226080
> +wm 32 0xb8001010 0x0000000c
> +wm 32 0x80000000 0xdeadbeef
> +wm 32 0xb8001030 0x00e78000
> +wm 32 0x43fac004 0x00000004
> +wm 32 0x43fac328 0x00002100
> +wm 32 0x43fac7d0 0x00000000
> diff --git a/arch/arm/boards/kindle3/kindle3.c b/arch/arm/boards/kindle3/kindle3.c
> new file mode 100644
> index 0000000..e06b3d7
> --- /dev/null
> +++ b/arch/arm/boards/kindle3/kindle3.c
> @@ -0,0 +1,318 @@
> +/*
> + * (C) 2007 Pengutronix, Sascha Hauer <s.hauer@pengutronix.de>
> + * (C) 2016 Alexander Kurz <akurz@blala.de>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + * Board support for the Amazon Kindle 3rd generation
> + */
> +
> +#include <common.h>
> +#include <command.h>
> +#include <driver.h>
> +#include <init.h>
> +#include <bootsource.h>
> +#include <io.h>
> +#include <environment.h>
> +#include <generated/mach-types.h>
> +#include <asm/armlinux.h>
> +#include <asm/mmu.h>
> +#include <asm/setup.h>
> +#include <mach/imx35-regs.h>
> +#include <mach/imx-pll.h>
> +#include <mach/iomux-mx35.h>
> +#include <mach/devices-imx35.h>
> +#include <mach/generic.h>
> +#include <usb/fsl_usb2.h>
> +#include <mach/usb.h>
> +#include <mach/spi.h>
> +#include <spi/spi.h>
> +#include <magicvar.h>
> +
> +/* 16 byte id for serial number */
> +#define ATAG_SERIAL16   0x5441000a
> +/* 16 byte id for a board revision */
> +#define ATAG_REVISION16 0x5441000b
> +
> +struct char16_tag {
> +	char data[16];
> +};
> +
> +static struct tag *setup_16char_tag(struct tag *params, uint32_t tag,
> +				    const char *value)
> +{
> +	struct char16_tag *target;
> +	target = ((void *) params) + sizeof(struct tag_header);
> +	params->hdr.tag = tag;
> +	params->hdr.size = tag_size(char16_tag);
> +	memcpy(target->data, value, sizeof target->data);
> +	return tag_next(params);
> +}
> +
> +static const char *get_env_16char_tag(const char *tag)
> +{
> +	static const char *default16 = "0000000000000000";
> +	const char *value;
> +	value = getenv(tag);
> +	if (!value) {
> +		printf("env var %s not found, using default\n", tag);
> +		return default16;
> +	}
> +	if (strlen(value) != 16) {
> +		printf("env var %s: expecting 16 characters, using default\n",
> +			tag);
> +		return default16;
> +	}
> +	printf("%s: %s\n", tag, value);
> +	return value;
> +}
> +
> +BAREBOX_MAGICVAR_NAMED(global_atags_serial16, global.board.serial16,
> +	"Pass the kindle Serial as vendor-specific ATAG to linux");
> +BAREBOX_MAGICVAR_NAMED(global_atags_revision16, global.board.revision16,
> +	"Pass the kindle BoardId as vendor-specific ATAG to linux");
> +
> +/* The Kindle3 Kernel expects two custom ATAGs, ATAG_REVISION16 describing
> + * the board and ATAG_SERIAL16 to identify the individual device.
> + */
> +struct tag *kindle3_append_atags(struct tag *params)
> +{
> +	params = setup_16char_tag(params, ATAG_SERIAL16,
> +				get_env_16char_tag("global.board.serial16"));
> +	params = setup_16char_tag(params, ATAG_REVISION16,
> +				get_env_16char_tag("global.board.revision16"));
> +	return params;
> +}
> +
> +static struct fsl_usb2_platform_data kindle3_usb_info = {
> +	.operating_mode = FSL_USB2_DR_DEVICE,
> +	.phy_mode = FSL_USB2_PHY_UTMI,
> +};
> +
> +/* SPI master devices. */
> +static int kindle3_spi0_internal_chipselect[] = {
> +	IMX_GPIO_NR(1, 18),
> +};
> +
> +static struct spi_imx_master kindle3_spi0_info = {
> +	.chipselect	= kindle3_spi0_internal_chipselect,
> +	.num_chipselect	= ARRAY_SIZE(kindle3_spi0_internal_chipselect),
> +};
> +
> +static const struct spi_board_info kindle3_spi_board_info[] = {
> +	{
> +		.name		= "mc13892",
> +		.bus_num	= 0,
> +		.chip_select	= 0,
> +		.mode		= SPI_CS_HIGH,
> +	},
> +};
> +
> +static int kindle3_mmu_init(void)
> +{
> +	l2x0_init((void __iomem *)0x30000000, 0x00030024, 0x00000000);
> +
> +	return 0;
> +}
> +postmmu_initcall(kindle3_mmu_init);
> +
> +static int kindle3_devices_init(void)
> +{
> +	imx35_add_mmc0(NULL);
> +
> +	if (IS_ENABLED(CONFIG_USB_GADGET)) {
> +		unsigned int tmp;
> +		/* Workaround ENGcm09152 */
> +		tmp = readl(MX35_USB_OTG_BASE_ADDR + 0x608);
> +		writel(tmp | (1 << 23), MX35_USB_OTG_BASE_ADDR + 0x608);
> +		add_generic_device("fsl-udc", DEVICE_ID_DYNAMIC, NULL,
> +				   MX35_USB_OTG_BASE_ADDR, 0x200,
> +				   IORESOURCE_MEM, &kindle3_usb_info);
> +	}
> +
> +	/* The kindle3 related linux patch published by amazon bluntly
> +	 * renamed MACH_MX35_3DS to MACH_MX35_LUIGI
> +	 */
> +	armlinux_set_architecture(MACH_TYPE_MX35_3DS);
> +
> +	/* Compatibility ATAGs for original kernel */
> +	armlinux_set_atag_appender(kindle3_append_atags);
> +	return 0;
> +}
> +device_initcall(kindle3_devices_init);
> +
> +static iomux_v3_cfg_t kindle3_pads[] = {
> +	/* UART1 */
> +	MX35_PAD_RXD1__UART1_RXD_MUX,
> +	MX35_PAD_TXD1__UART1_TXD_MUX,
> +
> +	/* eMMC */
> +	MX35_PAD_SD1_CMD__ESDHC1_CMD,
> +	MX35_PAD_SD1_CLK__ESDHC1_CLK,
> +	MX35_PAD_SD1_DATA0__ESDHC1_DAT0,
> +	MX35_PAD_SD1_DATA1__ESDHC1_DAT1,
> +	MX35_PAD_SD1_DATA2__ESDHC1_DAT2,
> +	MX35_PAD_SD1_DATA3__ESDHC1_DAT3,
> +
> +	/* USB */
> +	MX35_PAD_USBOTG_PWR__USB_TOP_USBOTG_PWR,
> +	MX35_PAD_USBOTG_OC__USB_TOP_USBOTG_OC,
> +
> +	/* I2C 1+2 */
> +	MX35_PAD_I2C1_CLK__I2C1_SCL,
> +	MX35_PAD_I2C1_DAT__I2C1_SDA,
> +	MX35_PAD_I2C2_CLK__I2C2_SCL,
> +	MX35_PAD_I2C2_DAT__I2C2_SDA,
> +
> +	/* SPI */
> +	MX35_PAD_CSPI1_SS0__GPIO1_18,
> +	MX35_PAD_CSPI1_SCLK__CSPI1_SCLK,
> +	MX35_PAD_CSPI1_MOSI__CSPI1_MOSI,
> +	MX35_PAD_CSPI1_MISO__CSPI1_MISO,
> +	MX35_PAD_CSPI1_SPI_RDY__CSPI1_RDY,
> +
> +	/* fiveway device: up, down, left, right, select */
> +	MX35_PAD_ATA_DATA14__GPIO2_27,
> +	MX35_PAD_ATA_DATA15__GPIO2_28,
> +	MX35_PAD_TX5_RX0__GPIO1_10,
> +	MX35_PAD_ATA_BUFF_EN__GPIO2_30,
> +	IOMUX_PAD(0x728, 0x2c4, 5, 0x8c8, 1,
> +		  PAD_CTL_PUS_100K_UP | PAD_CTL_HYS | PAD_CTL_DVS),
> +
> +	/* Volume keys: up, down */
> +	MX35_PAD_SCKR__GPIO1_4,
> +	MX35_PAD_FSR__GPIO1_5,
> +
> +};
> +
> +static int kindle3_part_init(void)
> +{
> +	devfs_add_partition("disk0", SZ_1K, 2 * SZ_1K,
> +			    DEVFS_PARTITION_FIXED, "disk0.imx_header");
> +	devfs_add_partition("disk0", 4 * SZ_1K, (192 - 1) * SZ_1K,
> +			    DEVFS_PARTITION_FIXED, "disk0.self");
> +	devfs_add_partition("disk0", (192 + 3) * SZ_1K, SZ_64K,
> +			    DEVFS_PARTITION_FIXED, "env0");
> +	devfs_add_partition("disk0", (256 + 3) * SZ_1K, SZ_1K,
> +			    DEVFS_PARTITION_FIXED, "disk0.serial");
> +	devfs_add_partition("disk0", (256 + 4) * SZ_1K, 3407872,
> +			    DEVFS_PARTITION_FIXED, "disk0.kernel");
> +	devfs_add_partition("disk0", 3674112, SZ_256K,
> +			    DEVFS_PARTITION_FIXED, "disk0.waveform");
> +	return 0;
> +}
> +
> +late_initcall(kindle3_part_init);
> +
> +static int imx35_console_init(void)
> +{
> +	mxc_iomux_v3_setup_multiple_pads(kindle3_pads,
> +					 ARRAY_SIZE(kindle3_pads));
> +
> +	barebox_set_model("Kindle3");
> +	barebox_set_hostname("kindle3");
> +
> +	imx35_add_uart0();
> +
> +	spi_register_board_info(kindle3_spi_board_info,
> +				ARRAY_SIZE(kindle3_spi_board_info));
> +	imx35_add_spi0(&kindle3_spi0_info);
> +
> +	imx35_add_i2c0(NULL);
> +	imx35_add_i2c1(NULL);
> +	return 0;
> +}
> +console_initcall(imx35_console_init);
> +
> +static int kindle3_core_setup(void)
> +{
> +	u32 tmp;
> +
> +	/* AIPS setup - Only setup MPROTx registers.
> +	 * The PACR default values are good.
> +	 */
> +	/*
> +	 * Set all MPROTx to be non-bufferable, trusted for R/W,
> +	 * not forced to user-mode.
> +	 */
> +	writel(0x77777777, MX35_AIPS1_BASE_ADDR);
> +	writel(0x77777777, MX35_AIPS1_BASE_ADDR + 0x4);
> +	writel(0x77777777, MX35_AIPS2_BASE_ADDR);
> +	writel(0x77777777, MX35_AIPS2_BASE_ADDR + 0x4);
> +
> +	/*
> +	 * Clear the on and off peripheral modules Supervisor Protect bit
> +	 * for SDMA to access them. Did not change the AIPS control registers
> +	 * (offset 0x20) access type
> +	 */
> +	writel(0x0, MX35_AIPS1_BASE_ADDR + 0x40);
> +	writel(0x0, MX35_AIPS1_BASE_ADDR + 0x44);
> +	writel(0x0, MX35_AIPS1_BASE_ADDR + 0x48);
> +	writel(0x0, MX35_AIPS1_BASE_ADDR + 0x4C);
> +	tmp = readl(MX35_AIPS1_BASE_ADDR + 0x50);
> +	tmp &= 0x00FFFFFF;
> +	writel(tmp, MX35_AIPS1_BASE_ADDR + 0x50);
> +
> +	writel(0x0, MX35_AIPS2_BASE_ADDR + 0x40);
> +	writel(0x0, MX35_AIPS2_BASE_ADDR + 0x44);
> +	writel(0x0, MX35_AIPS2_BASE_ADDR + 0x48);
> +	writel(0x0, MX35_AIPS2_BASE_ADDR + 0x4C);
> +	tmp = readl(MX35_AIPS2_BASE_ADDR + 0x50);
> +	tmp &= 0x00FFFFFF;
> +	writel(tmp, MX35_AIPS2_BASE_ADDR + 0x50);
> +
> +	/* MAX (Multi-Layer AHB Crossbar Switch) setup */
> +
> +	/* MPR - priority is M4 > M2 > M3 > M5 > M0 > M1 */
> +#define MAX_PARAM1 0x00302154
> +	writel(MAX_PARAM1, MX35_MAX_BASE_ADDR + 0x0);   /* for S0 */
> +	writel(MAX_PARAM1, MX35_MAX_BASE_ADDR + 0x100); /* for S1 */
> +	writel(MAX_PARAM1, MX35_MAX_BASE_ADDR + 0x200); /* for S2 */
> +	writel(MAX_PARAM1, MX35_MAX_BASE_ADDR + 0x300); /* for S3 */
> +	writel(MAX_PARAM1, MX35_MAX_BASE_ADDR + 0x400); /* for S4 */
> +
> +	/* SGPCR - always park on last master */
> +	writel(0x10, MX35_MAX_BASE_ADDR + 0x10);	/* for S0 */
> +	writel(0x10, MX35_MAX_BASE_ADDR + 0x110);	/* for S1 */
> +	writel(0x10, MX35_MAX_BASE_ADDR + 0x210);	/* for S2 */
> +	writel(0x10, MX35_MAX_BASE_ADDR + 0x310);	/* for S3 */
> +	writel(0x10, MX35_MAX_BASE_ADDR + 0x410);	/* for S4 */
> +
> +	/* MGPCR - restore default values */
> +	writel(0x0, MX35_MAX_BASE_ADDR + 0x800);	/* for M0 */
> +	writel(0x0, MX35_MAX_BASE_ADDR + 0x900);	/* for M1 */
> +	writel(0x0, MX35_MAX_BASE_ADDR + 0xa00);	/* for M2 */
> +	writel(0x0, MX35_MAX_BASE_ADDR + 0xb00);	/* for M3 */
> +	writel(0x0, MX35_MAX_BASE_ADDR + 0xc00);	/* for M4 */
> +	writel(0x0, MX35_MAX_BASE_ADDR + 0xd00);	/* for M5 */
> +
> +	/*
> +	 * M3IF Control Register (M3IFCTL)
> +	 * MRRP[0] = L2CC0 not on priority list (0 << 0)	= 0x00000000
> +	 * MRRP[1] = MAX1 not on priority list (0 << 0)		= 0x00000000
> +	 * MRRP[2] = L2CC1 not on priority list (0 << 0)	= 0x00000000
> +	 * MRRP[3] = USB  not on priority list (0 << 0)		= 0x00000000
> +	 * MRRP[4] = SDMA not on priority list (0 << 0)		= 0x00000000
> +	 * MRRP[5] = GPU not on priority list (0 << 0)		= 0x00000000
> +	 * MRRP[6] = IPU1 on priority list (1 << 6)		= 0x00000040
> +	 * MRRP[7] = IPU2 not on priority list (0 << 0)		= 0x00000000
> +	 *                                                       ------------
> +	 *                                                        0x00000040
> +	 */
> +	writel(0x40, MX35_M3IF_BASE_ADDR);
> +
> +	return 0;
> +}
> +
> +core_initcall(kindle3_core_setup);
> diff --git a/arch/arm/boards/kindle3/lowlevel.c b/arch/arm/boards/kindle3/lowlevel.c
> new file mode 100644
> index 0000000..58e6318
> --- /dev/null
> +++ b/arch/arm/boards/kindle3/lowlevel.c
> @@ -0,0 +1,142 @@
> +/*
> + *
> + * (c) 2007 Pengutronix, Sascha Hauer <s.hauer@pengutronix.de>
> + * (c) 2016 Alexander Kurz <akurz@blala.de>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + */
> +#include <common.h>
> +#include <init.h>
> +#include <mach/imx35-regs.h>
> +#include <mach/imx-pll.h>
> +#include <mach/esdctl.h>
> +#include <asm/cache-l2x0.h>
> +#include <io.h>
> +#include <mach/imx-nand.h>
> +#include <asm/barebox-arm.h>
> +#include <asm/barebox-arm-head.h>
> +#include <asm/sections.h>
> +#include <asm-generic/memory_layout.h>
> +#include <asm/system.h>
> +
> +void __bare_init __naked barebox_arm_reset_vector(void)
> +{
> +	uint32_t r, s;
> +	unsigned long ccm_base = MX35_CCM_BASE_ADDR;
> +	register uint32_t loops = 0x20000;
> +
> +	arm_cpu_lowlevel_init();
> +
> +	arm_setup_stack(MX35_IRAM_BASE_ADDR + MX35_IRAM_SIZE - 8);
> +
> +	r = get_cr();
> +	r |= CR_Z; /* Flow prediction (Z) */
> +	r |= CR_U; /* unaligned accesses  */
> +	r |= CR_FI; /* Low Int Latency     */
> +
> +	__asm__ __volatile__("mrc p15, 0, %0, c1, c0, 1" : "=r"(s));
> +	s |= 0x7;
> +	__asm__ __volatile__("mcr p15, 0, %0, c1, c0, 1" : : "r"(s));
> +
> +	set_cr(r);
> +
> +	r = 0;
> +	__asm__ __volatile__("mcr p15, 0, %0, c15, c2, 4" : : "r"(r));
> +
> +	/*
> +	 * Branch predicition is now enabled.  Flush the BTAC to ensure a valid
> +	 * starting point.  Don't flush BTAC while it is disabled to avoid
> +	 * ARM1136 erratum 408023.
> +	 */
> +	__asm__ __volatile__("mcr p15, 0, %0, c7, c5, 6" : : "r"(r));
> +
> +	/* invalidate I cache and D cache */
> +	__asm__ __volatile__("mcr p15, 0, %0, c7, c7, 0" : : "r"(r));
> +
> +	/* invalidate TLBs */
> +	__asm__ __volatile__("mcr p15, 0, %0, c8, c7, 0" : : "r"(r));
> +
> +	/* Drain the write buffer */
> +	__asm__ __volatile__("mcr p15, 0, %0, c7, c10, 4" : : "r"(r));
> +
> +	/* Also setup the Peripheral Port Remap register inside the core */
> +	r = 0x40000015; /* start from AIPS 2GB region */
> +	__asm__ __volatile__("mcr p15, 0, %0, c15, c2, 4" : : "r"(r));
> +
> +	/*
> +	 * End of ARM1136 init
> +	 */
> +
> +	writel(0x003F4208, ccm_base + MX35_CCM_CCMR);
> +
> +	/* Set MPLL , arm clock and ahb clock*/
> +	writel(MPCTL_PARAM_532, ccm_base + MX35_CCM_MPCTL);
> +
> +	writel(PPCTL_PARAM_300, ccm_base + MX35_CCM_PPCTL);
> +	writel(0x00001000, ccm_base + MX35_CCM_PDR0);
> +
> +	r = readl(ccm_base + MX35_CCM_CGR0);
> +	r |= 0x3 << MX35_CCM_CGR0_CSPI1_SHIFT;
> +	r |= 0x3 << MX35_CCM_CGR0_EPIT1_SHIFT;
> +	r |= 0x3 << MX35_CCM_CGR0_ESDHC1_SHIFT;
> +	writel(r, ccm_base + MX35_CCM_CGR0);
> +
> +	r = readl(ccm_base + MX35_CCM_CGR1);
> +	r |= 0x3 << MX35_CCM_CGR1_IOMUX_SHIFT;
> +	r |= 0x3 << MX35_CCM_CGR1_I2C1_SHIFT;
> +	r |= 0x3 << MX35_CCM_CGR1_I2C2_SHIFT;
> +	r |= 0x3 << MX35_CCM_CGR1_GPIO1_SHIFT;
> +	r |= 0x3 << MX35_CCM_CGR1_GPIO2_SHIFT;
> +	writel(r, ccm_base + MX35_CCM_CGR1);
> +
> +	r = readl(MX35_L2CC_BASE_ADDR + L2X0_AUX_CTRL);
> +	r |= 0x1000;
> +	writel(r, MX35_L2CC_BASE_ADDR + L2X0_AUX_CTRL);
> +
> +	/* Skip SDRAM initialization if we run from RAM */
> +	r = get_pc();
> +	if (r > 0x80000000 && r < 0x90000000)
> +		goto out;
> +
> +	/* Init Mobile DDR */
> +	writel(0x0000000E, MX35_ESDCTL_BASE_ADDR + IMX_ESDMISC);
> +	/* ESD_MISC: Enable DDR SDRAM */
> +	writel(0x00000004, MX35_ESDCTL_BASE_ADDR + IMX_ESDMISC);
> +	__asm__ volatile ("1:\n"
> +			"subs %0, %1, #1\n"
> +			"bne 1b" : "=r" (loops) : "0" (loops));
> +
> +	writel(0x0019672f, MX35_ESDCTL_BASE_ADDR + IMX_ESDCFG0);
> +	/* ESD_ESDCTL0 : select Prechare-All mode */
> +	writel(0x93220000, MX35_ESDCTL_BASE_ADDR + IMX_ESDCTL0);
> +	writeb(0xda, MX35_CSD0_BASE_ADDR + 0x400);
> +	/* ESD_ESDCTL0: Auto Refresh command */
> +	writel(0xA3220000, MX35_ESDCTL_BASE_ADDR + IMX_ESDCTL0);
> +	writeb(0xda, MX35_CSD0_BASE_ADDR);
> +	writeb(0xda, MX35_CSD0_BASE_ADDR);
> +	/* ESD_ESDCTL0: Load Mode Register */
> +	writel(0xB3220000, MX35_ESDCTL_BASE_ADDR + IMX_ESDCTL0);
> +	writeb(0xda, MX35_CSD0_BASE_ADDR + 0x33);
> +	writeb(0xff, MX35_CSD0_BASE_ADDR + 0x2000000);
> +	/* ESD_ESDCTL0: enable Auto-Refresh */
> +	writel(0x83228080, MX35_ESDCTL_BASE_ADDR + IMX_ESDCTL0);
> +
> +	writel(0x0000000c, MX35_ESDCTL_BASE_ADDR + IMX_ESDMISC);
> +	writel(0xdeadbeef, MX35_CSD0_BASE_ADDR);
> +	writel(0x00e78000, MX35_CSD0_BASE_ADDR + 0x1030);
> +
> +out:
> +	imx35_barebox_entry(NULL);
> +}
> diff --git a/arch/arm/configs/kindle3_defconfig b/arch/arm/configs/kindle3_defconfig
> new file mode 100644
> index 0000000..0b7088e
> --- /dev/null
> +++ b/arch/arm/configs/kindle3_defconfig
> @@ -0,0 +1,65 @@
> +CONFIG_ARCH_IMX=y
> +CONFIG_BAREBOX_MAX_IMAGE_SIZE=0x30000
> +CONFIG_MACH_KINDLE3=y
> +CONFIG_ARCH_IMX_USBLOADER=y
> +CONFIG_IMX_IIM=y
> +CONFIG_AEABI=y
> +CONFIG_ARM_BOARD_APPEND_ATAG=y
> +CONFIG_ARM_BOARD_PREPEND_ATAG=y
> +CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y
> +CONFIG_PBL_IMAGE=y
> +CONFIG_PBL_RELOCATABLE=y
> +CONFIG_IMAGE_COMPRESSION_XZKERN=y
> +CONFIG_MALLOC_SIZE=0x2000000
> +CONFIG_MALLOC_TLSF=y
> +CONFIG_RELOCATABLE=y
> +CONFIG_HUSH_FANCY_PROMPT=y
> +CONFIG_CMDLINE_EDITING=y
> +CONFIG_AUTO_COMPLETE=y
> +CONFIG_BOOTM_OFTREE=y
> +CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW=y
> +CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/kindle3/env/"
> +CONFIG_RESET_SOURCE=y
> +CONFIG_CMD_DMESG=y
> +CONFIG_LONGHELP=y
> +CONFIG_CMD_MEMINFO=y
> +CONFIG_CMD_MMC_EXTCSD=y
> +# CONFIG_CMD_BOOTU is not set
> +CONFIG_CMD_BOOTZ=y
> +CONFIG_CMD_GO=y
> +CONFIG_CMD_LOADY=y
> +CONFIG_CMD_RESET=y
> +CONFIG_CMD_UIMAGE=y
> +CONFIG_CMD_PARTITION=y
> +CONFIG_CMD_EXPORT=y
> +CONFIG_CMD_DEFAULTENV=y
> +CONFIG_CMD_LOADENV=y
> +CONFIG_CMD_PRINTENV=y
> +CONFIG_CMD_MAGICVAR=y
> +CONFIG_CMD_MAGICVAR_HELP=y
> +CONFIG_CMD_SAVEENV=y
> +CONFIG_CMD_READF=y
> +CONFIG_CMD_SLEEP=y
> +CONFIG_CMD_EDIT=y
> +CONFIG_CMD_READLINE=y
> +CONFIG_CMD_TIMEOUT=y
> +CONFIG_CMD_CRC=y
> +CONFIG_CMD_CRC_CMP=y
> +CONFIG_CMD_MEMTEST=y
> +CONFIG_CMD_GPIO=y
> +CONFIG_CMD_I2C=y
> +CONFIG_CMD_SPI=y
> +CONFIG_CMD_USBGADGET=y
> +CONFIG_DRIVER_SPI_IMX=y
> +CONFIG_I2C=y
> +CONFIG_I2C_IMX=y
> +CONFIG_USB_GADGET=y
> +CONFIG_USB_GADGET_SERIAL=y
> +CONFIG_MCI=y
> +CONFIG_MCI_STARTUP=y
> +CONFIG_MCI_IMX_ESDHC=y
> +CONFIG_MFD_MC13XXX=y
> +CONFIG_FS_EXT4=y
> +CONFIG_FS_FAT=y
> +CONFIG_FS_FAT_WRITE=y
> +CONFIG_FS_FAT_LFN=y
> diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
> index 5b648ac..80f8fd8 100644
> --- a/arch/arm/mach-imx/Kconfig
> +++ b/arch/arm/mach-imx/Kconfig
> @@ -33,6 +33,7 @@ config ARCH_TEXT_BASE
>  	default 0x17800000 if MACH_SABRESD
>  	default 0x4fc00000 if MACH_REALQ7
>  	default 0x4fc00000 if MACH_GK802
> +	default 0x87f00000 if MACH_KINDLE3
>  	default 0x2fc00000 if MACH_TQMA6X
>  	default 0x4fc00000 if MACH_DFI_FS700_M60
>  	default 0x4fc00000 if MACH_UDOO
> @@ -453,6 +454,14 @@ config MACH_GUF_CUPID
>  	  Say Y here if you are using the Garz+Fricke Neso board equipped
>  	  with a Freescale i.MX35 Processor
>  
> +config MACH_KINDLE3
> +	bool "Amazon Kindle3"
> +	select ARCH_IMX35
> +	select ARCH_HAS_L2X0
> +	select HAVE_DEFAULT_ENVIRONMENT_NEW
> +	help
> +	  Say Y here if you are using the Amazon Model No. D00901 Kindle
> +
>  # ----------------------------------------------------------
>  
>  comment "i.MX51 Boards"
> -- 
> 2.1.4
> 
> 
> _______________________________________________
> barebox mailing list
> barebox@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
> 

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

      reply	other threads:[~2016-07-11  5:52 UTC|newest]

Thread overview: 2+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2016-07-09 13:09 Alexander Kurz
2016-07-11  5:51 ` Sascha Hauer [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20160711055159.GV20657@pengutronix.de \
    --to=s.hauer@pengutronix.de \
    --cc=akurz@blala.de \
    --cc=barebox@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox