From: Andrey Smirnov <andrew.smirnov@gmail.com>
To: barebox@lists.infradead.org
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Subject: [PATCH v2] i.MX: vf610: Add support for ZII VF610 Dev Family
Date: Fri, 3 Feb 2017 07:53:23 -0800 [thread overview]
Message-ID: <20170203155323.29430-1-andrew.smirnov@gmail.com> (raw)
Add support for ZII VF610 Dev based designs such as:
- VF610 Dev, revision B
- VF610 Dev, revision C
- CFU1, revision A
- SPU3, revision A
- SCU4 AIB, revision C
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
---
Changes since v1:
- Removed questionable preprocessor-level checks
- Converted board.c to use 'struct gpio'/gpio_request_array
(as opposed to using custom type)
arch/arm/boards/Makefile | 1 +
arch/arm/boards/zii-vf610-dev/Makefile | 3 +
arch/arm/boards/zii-vf610-dev/board.c | 149 +++++++
.../zii-vf610-dev/defaultenv-zii-vf610-dev/boot/sd | 4 +
.../defaultenv-zii-vf610-dev/init/automount-sd | 13 +
.../defaultenv-zii-vf610-dev/init/choose-dtb | 4 +
| 243 +++++++++++
arch/arm/boards/zii-vf610-dev/lowlevel.c | 137 ++++++
arch/arm/configs/zii_vf610_dev_defconfig | 165 ++++++++
arch/arm/dts/Makefile | 7 +
arch/arm/dts/vf610-zii-cfu1-rev-a.dts | 208 ++++++++++
arch/arm/dts/vf610-zii-dev-rev-b.dts | 431 +++++++++++++++++++
arch/arm/dts/vf610-zii-dev-rev-c.dts | 445 ++++++++++++++++++++
arch/arm/dts/vf610-zii-dev.dtsi | 436 ++++++++++++++++++++
arch/arm/dts/vf610-zii-scu4-aib-rev-c.dts | 457 +++++++++++++++++++++
arch/arm/dts/vf610-zii-spu3-rev-a.dts | 140 +++++++
arch/arm/mach-imx/Kconfig | 5 +
images/Makefile.imx | 5 +
18 files changed, 2853 insertions(+)
create mode 100644 arch/arm/boards/zii-vf610-dev/Makefile
create mode 100644 arch/arm/boards/zii-vf610-dev/board.c
create mode 100644 arch/arm/boards/zii-vf610-dev/defaultenv-zii-vf610-dev/boot/sd
create mode 100644 arch/arm/boards/zii-vf610-dev/defaultenv-zii-vf610-dev/init/automount-sd
create mode 100644 arch/arm/boards/zii-vf610-dev/defaultenv-zii-vf610-dev/init/choose-dtb
create mode 100644 arch/arm/boards/zii-vf610-dev/flash-header-zii-vf610-dev.imxcfg
create mode 100644 arch/arm/boards/zii-vf610-dev/lowlevel.c
create mode 100644 arch/arm/configs/zii_vf610_dev_defconfig
create mode 100644 arch/arm/dts/vf610-zii-cfu1-rev-a.dts
create mode 100644 arch/arm/dts/vf610-zii-dev-rev-b.dts
create mode 100644 arch/arm/dts/vf610-zii-dev-rev-c.dts
create mode 100644 arch/arm/dts/vf610-zii-dev.dtsi
create mode 100644 arch/arm/dts/vf610-zii-scu4-aib-rev-c.dts
create mode 100644 arch/arm/dts/vf610-zii-spu3-rev-a.dts
diff --git a/arch/arm/boards/Makefile b/arch/arm/boards/Makefile
index fe5c209..cd8f49f 100644
--- a/arch/arm/boards/Makefile
+++ b/arch/arm/boards/Makefile
@@ -142,3 +142,4 @@ obj-$(CONFIG_MACH_VSCOM_BALTOS) += vscom-baltos/
obj-$(CONFIG_MACH_QEMU_VIRT64) += qemu-virt64/
obj-$(CONFIG_MACH_VF610_TWR) += freescale-vf610-twr/
obj-$(CONFIG_MACH_ZII_RDU2) += zii-imx6q-rdu2/
+obj-$(CONFIG_MACH_ZII_VF610_DEV) += zii-vf610-dev/
diff --git a/arch/arm/boards/zii-vf610-dev/Makefile b/arch/arm/boards/zii-vf610-dev/Makefile
new file mode 100644
index 0000000..1297d81
--- /dev/null
+++ b/arch/arm/boards/zii-vf610-dev/Makefile
@@ -0,0 +1,3 @@
+obj-y += board.o
+lwl-y += lowlevel.o
+bbenv-y += defaultenv-zii-vf610-dev
diff --git a/arch/arm/boards/zii-vf610-dev/board.c b/arch/arm/boards/zii-vf610-dev/board.c
new file mode 100644
index 0000000..eea3828
--- /dev/null
+++ b/arch/arm/boards/zii-vf610-dev/board.c
@@ -0,0 +1,149 @@
+/*
+ * Copyright (C) 2016 Zodiac Inflight Innovation
+ * Author: Andrey Smirnov <andrew.smirnov@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <init.h>
+#include <gpio.h>
+#include <environment.h>
+#include <linux/clk.h>
+#include <dt-bindings/clock/vf610-clock.h>
+#include <envfs.h>
+
+
+static int expose_signals(const struct gpio *signals,
+ size_t signal_num)
+{
+ int ret, i;
+
+ ret = gpio_request_array(signals, signal_num);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < signal_num; i++)
+ export_env_ull(signals[i].label, signals[i].gpio);
+
+ return 0;
+}
+
+static int zii_vf610_cfu1_expose_signals(void)
+{
+ static const struct gpio signals[] = {
+ {
+ .gpio = 132,
+ .flags = GPIOF_IN,
+ .label = "fim_sd",
+ },
+ {
+ .gpio = 118,
+ .flags = GPIOF_OUT_INIT_LOW,
+ .label = "fim_tdis",
+ },
+ };
+
+ if (!of_machine_is_compatible("zii,vf610cfu1-a"))
+ return 0;
+
+ return expose_signals(signals, ARRAY_SIZE(signals));
+}
+late_initcall(zii_vf610_cfu1_expose_signals);
+
+static int zii_vf610_cfu1_spu3_expose_signals(void)
+{
+ static const struct gpio signals[] = {
+ {
+ .gpio = 107,
+ .flags = GPIOF_OUT_INIT_LOW,
+ .label = "soc_sw_rstn",
+ },
+ {
+ .gpio = 98,
+ .flags = GPIOF_IN,
+ .label = "e6352_intn",
+ },
+ };
+
+ if (!of_machine_is_compatible("zii,vf610spu3-a") &&
+ !of_machine_is_compatible("zii,vf610cfu1-a"))
+ return 0;
+
+ return expose_signals(signals, ARRAY_SIZE(signals));
+}
+late_initcall(zii_vf610_cfu1_spu3_expose_signals);
+
+static int zii_vf610_dev_print_clocks(void)
+{
+ int i;
+ struct clk *clk;
+ struct device_node *ccm_np;
+ const unsigned long MHz = 1000000;
+ const char *clk_names[] = { "cpu", "ddr", "bus", "ipg" };
+
+ if (!of_machine_is_compatible("zii,vf610dev"))
+ return 0;
+
+ ccm_np = of_find_compatible_node(NULL, NULL, "fsl,vf610-ccm");
+ if (!ccm_np) {
+ pr_err("Couln't get CCM node\n");
+ return -ENOENT;
+ }
+
+ for (i = 0; i < ARRAY_SIZE(clk_names); i++) {
+ unsigned long rate;
+ const char *name = clk_names[i];
+
+ clk = of_clk_get_by_name(ccm_np, name);
+ if (IS_ERR(clk)) {
+ pr_err("Failed to get '%s' clock (%ld)\n",
+ name, PTR_ERR(clk));
+ return PTR_ERR(clk);
+ }
+
+ rate = clk_get_rate(clk);
+
+ pr_info("%s clock : %8lu MHz\n", name, rate / MHz);
+ }
+
+ return 0;
+}
+late_initcall(zii_vf610_dev_print_clocks);
+
+static int zii_vf610_dev_set_hostname(void)
+{
+ size_t i;
+ static const struct {
+ const char *compatible;
+ const char *hostname;
+ } boards[] = {
+ { "zii,vf610spu3-a", "spu3-rev-a" },
+ { "zii,vf610cfu1-a", "cfu1-rev-a" },
+ { "zii,vf610dev-b", "dev-rev-b" },
+ { "zii,vf610dev-c", "dev-rev-c" },
+ { "zii,vf610scu4-aib-c", "scu4-aib-rev-c" },
+ };
+
+ if (!of_machine_is_compatible("zii,vf610dev"))
+ return 0;
+
+ for (i = 0; i < ARRAY_SIZE(boards); i++) {
+ if (of_machine_is_compatible(boards[i].compatible)) {
+ barebox_set_hostname(boards[i].hostname);
+ break;
+ }
+ }
+
+ defaultenv_append_directory(defaultenv_zii_vf610_dev);
+ return 0;
+}
+late_initcall(zii_vf610_dev_set_hostname);
diff --git a/arch/arm/boards/zii-vf610-dev/defaultenv-zii-vf610-dev/boot/sd b/arch/arm/boards/zii-vf610-dev/defaultenv-zii-vf610-dev/boot/sd
new file mode 100644
index 0000000..cf8eec3
--- /dev/null
+++ b/arch/arm/boards/zii-vf610-dev/defaultenv-zii-vf610-dev/boot/sd
@@ -0,0 +1,4 @@
+#!/bin/sh
+
+global.bootm.image=/mnt/sd/zImage
+global.bootm.oftree=/mnt/sd/${global.bootm.oftree}
diff --git a/arch/arm/boards/zii-vf610-dev/defaultenv-zii-vf610-dev/init/automount-sd b/arch/arm/boards/zii-vf610-dev/defaultenv-zii-vf610-dev/init/automount-sd
new file mode 100644
index 0000000..f44dab3
--- /dev/null
+++ b/arch/arm/boards/zii-vf610-dev/defaultenv-zii-vf610-dev/init/automount-sd
@@ -0,0 +1,13 @@
+#!/bin/sh
+
+if [ x${global.hostname} = xdev-rev-b -o x${global.hostname} = xdev-rev-c ];
+then
+ global sd=0
+else
+ global sd=1
+fi
+
+mkdir -p /mnt/sd
+automount /mnt/sd 'mci${global.sd}.probe=1 && mount /dev/disk${global.sd}.0 /mnt/sd'
+
+exit 0
diff --git a/arch/arm/boards/zii-vf610-dev/defaultenv-zii-vf610-dev/init/choose-dtb b/arch/arm/boards/zii-vf610-dev/defaultenv-zii-vf610-dev/init/choose-dtb
new file mode 100644
index 0000000..41a74c3
--- /dev/null
+++ b/arch/arm/boards/zii-vf610-dev/defaultenv-zii-vf610-dev/init/choose-dtb
@@ -0,0 +1,4 @@
+#!/bin/sh
+
+global.bootm.oftree=vf610-zii-${global.hostname}.dtb
+
--git a/arch/arm/boards/zii-vf610-dev/flash-header-zii-vf610-dev.imxcfg b/arch/arm/boards/zii-vf610-dev/flash-header-zii-vf610-dev.imxcfg
new file mode 100644
index 0000000..177f4e8
--- /dev/null
+++ b/arch/arm/boards/zii-vf610-dev/flash-header-zii-vf610-dev.imxcfg
@@ -0,0 +1,243 @@
+soc vf610
+loadaddr 0x80000000
+dcdofs 0x400
+
+#define VF610_DDR_PAD_CTRL 0x00000180 /* 25 Ohm drive strength */
+#define VF610_DDR_PAD_CTRL_1 0x00010180 /* 25 Ohm drive strength + differential input */
+
+#define DDRMC_PHY_DQ_TIMING 0x00002613
+#define DDRMC_PHY_DQS_TIMING 0x00002615
+#define DDRMC_PHY_CTRL 0x00210000
+#define DDRMC_PHY_MASTER_CTRL 0x0001012a
+#define DDRMC_PHY_SLAVE_CTRL 0x00002000
+#define DDRMC_PHY_OFF 0x00000000
+#define DDRMC_PHY_PROC_PAD_ODT 0x00010101
+
+#define CHECKPOINT(n) wm 32 0x3f000000 n
+
+CHECKPOINT(1)
+
+/* ======================= Clock initialization =======================*/
+
+/*
+ * Ungate all IP block clocks
+ */
+wm 32 0x4006b040 0xffffffff
+wm 32 0x4006b044 0xffffffff
+wm 32 0x4006b048 0xffffffff
+wm 32 0x4006b04c 0xffffffff
+wm 32 0x4006b050 0xffffffff
+wm 32 0x4006b058 0xffffffff
+wm 32 0x4006b05c 0xffffffff
+wm 32 0x4006b060 0xffffffff
+wm 32 0x4006b064 0xffffffff
+wm 32 0x4006b068 0xffffffff
+wm 32 0x4006b06c 0xffffffff
+
+
+/*
+ * Turn PLL2 on
+ */
+wm 32 0x40050030 0x00002001 /* Fout = Fin * 22 */
+
+CHECKPOINT(2)
+
+/*
+ * Wait for PLLs to lock
+ */
+check 32 while_any_bit_clear 0x40050030 0x80000000
+
+
+CHECKPOINT(3)
+
+clear_bits 32 0x4006b008 0x00000040
+set_bits 32 0x4006b008 0x00002000
+
+
+
+/* ======================= DDR IOMUX =======================*/
+
+CHECKPOINT(4)
+
+wm 32 0x40048220 0x00000180
+wm 32 0x40048224 0x00000180
+wm 32 0x40048228 0x00000180
+wm 32 0x4004822c 0x00000180
+wm 32 0x40048230 0x00000180
+wm 32 0x40048234 0x00000180
+wm 32 0x40048238 0x00000180
+wm 32 0x4004823c 0x00000180
+wm 32 0x40048240 0x00000180
+wm 32 0x40048244 0x00000180
+wm 32 0x40048248 0x00000180
+wm 32 0x4004824c 0x00000180
+wm 32 0x40048250 0x00000180
+wm 32 0x40048254 0x00000180
+wm 32 0x40048258 0x00000180
+wm 32 0x4004825c 0x00000180
+wm 32 0x40048260 0x00000180
+wm 32 0x40048264 0x00000180
+wm 32 0x40048268 0x00000180
+wm 32 0x4004826c 0x00000180
+wm 32 0x40048270 0x00000180
+wm 32 0x40048274 0x00000180
+wm 32 0x40048278 0x00000180
+wm 32 0x4004827c 0x00010180
+wm 32 0x40048280 0x00010180
+wm 32 0x40048284 0x00010180
+wm 32 0x40048288 0x00010180
+wm 32 0x4004828c 0x00010180
+wm 32 0x40048290 0x00010180
+wm 32 0x40048294 0x00010180
+wm 32 0x40048298 0x00010180
+wm 32 0x4004829c 0x00010180
+wm 32 0x400482a0 0x00010180
+wm 32 0x400482a4 0x00010180
+wm 32 0x400482a8 0x00010180
+wm 32 0x400482ac 0x00010180
+wm 32 0x400482b0 0x00010180
+wm 32 0x400482b4 0x00010180
+wm 32 0x400482b8 0x00010180
+wm 32 0x400482bc 0x00010180
+wm 32 0x400482c0 0x00010180
+wm 32 0x400482c4 0x00010180
+wm 32 0x400482c8 0x00010180
+wm 32 0x400482cc 0x00000180
+wm 32 0x400482d0 0x00000180
+wm 32 0x400482d4 0x00000180
+wm 32 0x400482d8 0x00000180
+wm 32 0x4004821c 0x00000180
+
+/* ======================= DDR Controller =======================*/
+
+CHECKPOINT(5)
+wm 32 0x400ae000 0x00000600
+wm 32 0x400ae008 0x00000005
+wm 32 0x400ae028 0x00013880
+wm 32 0x400ae02c 0x00030d40
+wm 32 0x400ae030 0x00000506
+wm 32 0x400ae034 0x06040400
+wm 32 0x400ae038 0x1006040e
+wm 32 0x400ae040 0x04040000
+wm 32 0x400ae044 0x006db00c
+wm 32 0x400ae048 0x00000403
+wm 32 0x400ae050 0x01000000
+wm 32 0x400ae054 0x00060001
+wm 32 0x400ae058 0x000c0000
+wm 32 0x400ae05c 0x03000200
+wm 32 0x400ae060 0x00000006
+wm 32 0x400ae064 0x00010000
+wm 32 0x400ae068 0x0c300068
+wm 32 0x400ae070 0x00000000
+wm 32 0x400ae074 0x00000003
+wm 32 0x400ae078 0x0000000a
+wm 32 0x400ae07c 0x006c0200
+wm 32 0x400ae084 0x00010000
+wm 32 0x400ae088 0x00050500
+wm 32 0x400ae098 0x00000000
+wm 32 0x400ae09c 0x04001002
+wm 32 0x400ae0a4 0x00000001
+wm 32 0x400ae0c0 0x00460420
+wm 32 0x400ae0c4 0x00000000
+wm 32 0x400ae0cc 0x00000000
+wm 32 0x400ae0e4 0x02000000
+wm 32 0x400ae108 0x01000200
+wm 32 0x400ae10c 0x00000040
+wm 32 0x400ae114 0x00000200
+wm 32 0x400ae118 0x00000040
+wm 32 0x400ae120 0x00000000
+wm 32 0x400ae124 0x0a010100
+wm 32 0x400ae128 0x01014040
+wm 32 0x400ae12c 0x01010101
+wm 32 0x400ae130 0x03030000
+wm 32 0x400ae134 0x01000101
+wm 32 0x400ae138 0x0700000c
+wm 32 0x400ae13c 0x00000000
+wm 32 0x400ae148 0x10000000
+wm 32 0x400ae15c 0x01000000
+wm 32 0x400ae160 0x00040000
+wm 32 0x400ae164 0x00000002
+wm 32 0x400ae16c 0x00020000
+wm 32 0x400ae180 0x00002819
+wm 32 0x400ae184 0x01000000
+wm 32 0x400ae188 0x00000000
+wm 32 0x400ae18c 0x00000000
+wm 32 0x400ae198 0x00000000
+wm 32 0x400ae1a4 0x00000c00
+wm 32 0x400ae1a8 0x00000000
+wm 32 0x400ae1b8 0x0000000c
+wm 32 0x400ae1c8 0x00000000
+wm 32 0x400ae1cc 0x00000000
+wm 32 0x400ae1d4 0x00000000
+wm 32 0x400ae1d8 0x01010000
+wm 32 0x400ae1e0 0x02020000
+wm 32 0x400ae1e4 0x00000202
+wm 32 0x400ae1e8 0x01010064
+wm 32 0x400ae1ec 0x00010101
+wm 32 0x400ae1f0 0x00000064
+wm 32 0x400ae1f8 0x00000800
+wm 32 0x400ae210 0x00000506
+wm 32 0x400ae224 0x00020000
+wm 32 0x400ae228 0x01000000
+wm 32 0x400ae22c 0x04070303
+wm 32 0x400ae230 0x00000040
+wm 32 0x400ae23c 0x06000080
+wm 32 0x400ae240 0x04070303
+wm 32 0x400ae244 0x00000040
+wm 32 0x400ae248 0x00000040
+wm 32 0x400ae24c 0x000f0000
+wm 32 0x400ae250 0x000f0000
+wm 32 0x400ae25c 0x00000101
+wm 32 0x400ae268 0x682c4000
+wm 32 0x400ae26c 0x00000012
+wm 32 0x400ae278 0x00000006
+wm 32 0x400ae284 0x00010202
+
+/* ======================= DDR PHY =======================*/
+
+CHECKPOINT(6)
+
+wm 32 0x400ae400 0x00002613
+wm 32 0x400ae440 0x00002613
+wm 32 0x400ae480 0x00002613
+wm 32 0x400ae404 0x00002615
+wm 32 0x400ae444 0x00002615
+wm 32 0x400ae408 0x00210000
+wm 32 0x400ae448 0x00210000
+wm 32 0x400ae488 0x00210000
+wm 32 0x400ae40c 0x0001012a
+wm 32 0x400ae44c 0x0001012a
+wm 32 0x400ae48c 0x0001012a
+wm 32 0x400ae410 0x00002000
+wm 32 0x400ae450 0x00002000
+wm 32 0x400ae490 0x00002000
+wm 32 0x400ae4c4 0x00000000
+wm 32 0x400ae4c8 0x00001100
+wm 32 0x400ae4d0 0x00010101
+wm 32 0x400ae000 0x00000601
+
+CHECKPOINT(7)
+
+check 32 while_any_bit_clear 0x400ae140 0x100
+# check 32 while_any_bit_clear 0x400ae42c 0x1
+# check 32 while_any_bit_clear 0x400ae46c 0x1
+# check 32 while_any_bit_clear 0x400ae4ac 0x1
+
+CHECKPOINT(8)
+
+wm 32 0x80000000 0xa5a5a5a5
+check 32 while_any_bit_clear 0x80000000 0xa5a5a5a5
+
+wm 32 0x400ae000 0x00000600
+wm 32 0x400ae000 0x00000601
+
+check 32 while_any_bit_clear 0x400ae140 0x100
+# check 32 while_any_bit_clear 0x400ae42c 0x1
+# check 32 while_any_bit_clear 0x400ae46c 0x1
+# check 32 while_any_bit_clear 0x400ae4ac 0x1
+
+/* wm 32 0x3f040000 0xf0
+ check 32 while_any_bit_clear 0x3f040000 0x0f */
+
+
+CHECKPOINT(9)
diff --git a/arch/arm/boards/zii-vf610-dev/lowlevel.c b/arch/arm/boards/zii-vf610-dev/lowlevel.c
new file mode 100644
index 0000000..95b68d5
--- /dev/null
+++ b/arch/arm/boards/zii-vf610-dev/lowlevel.c
@@ -0,0 +1,137 @@
+/*
+ * Copyright (C) 2016 Zodiac Inflight Innovation
+ * Author: Andrey Smirnov <andrew.smirnov@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <linux/sizes.h>
+#include <mach/generic.h>
+#include <asm/barebox-arm-head.h>
+#include <asm/barebox-arm.h>
+#include <mach/vf610-regs.h>
+#include <mach/clock-vf610.h>
+#include <mach/iomux-vf610.h>
+#include <debug_ll.h>
+
+static inline void setup_uart(void)
+{
+ void __iomem *iomux = IOMEM(VF610_IOMUXC_BASE_ADDR);
+
+ vf610_ungate_all_peripherals();
+ vf610_setup_pad(iomux, VF610_PAD_PTB10__UART0_TX);
+ vf610_uart_setup_ll();
+
+ putc_ll('>');
+}
+
+enum zii_platform_vf610_type {
+ ZII_PLATFORM_VF610_DEV_REV_B = 0x01,
+ ZII_PLATFORM_VF610_SCU4_AIB = 0x02,
+ ZII_PLATFORM_VF610_SPU3 = 0x03,
+ ZII_PLATFORM_VF610_CFU1 = 0x04,
+ ZII_PLATFORM_VF610_DEV_REV_C = 0x05,
+};
+
+unsigned int get_system_type(void)
+{
+#define GPIO_PDIR 0x10
+
+ u32 pdir;
+ void __iomem *gpio2 = IOMEM(VF610_GPIO2_BASE_ADDR);
+ void __iomem *iomux = IOMEM(VF610_IOMUXC_BASE_ADDR);
+ unsigned low, high;
+
+ /*
+ * System type is encoded as a 4-bit number specified by the
+ * following pins (pulled up or down with resistors on the
+ * board).
+ */
+ vf610_setup_pad(iomux, VF610_PAD_PTD16__GPIO_78);
+ vf610_setup_pad(iomux, VF610_PAD_PTD17__GPIO_77);
+ vf610_setup_pad(iomux, VF610_PAD_PTD18__GPIO_76);
+ vf610_setup_pad(iomux, VF610_PAD_PTD19__GPIO_75);
+
+ pdir = readl(gpio2 + GPIO_PDIR);
+
+ low = 75 % 32;
+ high = 78 % 32;
+
+ pdir &= GENMASK(high, low);
+ pdir >>= low;
+
+ return pdir;
+}
+
+extern char __dtb_vf610_zii_dev_rev_b_start[];
+extern char __dtb_vf610_zii_dev_rev_c_start[];
+extern char __dtb_vf610_zii_cfu1_rev_a_start[];
+extern char __dtb_vf610_zii_spu3_rev_a_start[];
+extern char __dtb_vf610_zii_scu4_aib_rev_c_start[];
+
+ENTRY_FUNCTION(start_zii_vf610_dev, r0, r1, r2)
+{
+ void *fdt;
+ const unsigned int system_type = get_system_type();
+
+ vf610_cpu_lowlevel_init();
+
+ if (IS_ENABLED(CONFIG_DEBUG_LL))
+ setup_uart();
+
+ switch (system_type) {
+ default:
+ /*
+ * GCC can be smart enough to, when DEBUG_LL is
+ * disabled, reduce this switch statement to a LUT
+ * fetch. Unfortunately here, this early in the boot
+ * process before any relocation/address fixups could
+ * happen, the address of that LUT used by the code is
+ * incorrect and any access to it would result in
+ * bogus values.
+ *
+ * Adding the following barrier() statement seem to
+ * force the compiler to always translate this block
+ * to a sequence of consecutive checks and jumps with
+ * relative fetches, which should work with or without
+ * relocation/fixups.
+ */
+ barrier();
+
+ if (IS_ENABLED(CONFIG_DEBUG_LL)) {
+ relocate_to_current_adr();
+ setup_c();
+ puts_ll("*********************************\n");
+ puts_ll("* Unknown system type: ");
+ puthex_ll(system_type);
+ puts_ll("\n* Assuming devboard revision B\n");
+ puts_ll("*********************************\n");
+ }
+ case ZII_PLATFORM_VF610_DEV_REV_B: /* FALLTHROUGH */
+ fdt = __dtb_vf610_zii_dev_rev_b_start;
+ break;
+ case ZII_PLATFORM_VF610_SCU4_AIB:
+ fdt = __dtb_vf610_zii_scu4_aib_rev_c_start;
+ break;
+ case ZII_PLATFORM_VF610_DEV_REV_C:
+ fdt = __dtb_vf610_zii_dev_rev_c_start;
+ break;
+ case ZII_PLATFORM_VF610_CFU1:
+ fdt = __dtb_vf610_zii_cfu1_rev_a_start;
+ break;
+ case ZII_PLATFORM_VF610_SPU3:
+ fdt = __dtb_vf610_zii_spu3_rev_a_start;
+ break;
+ }
+
+ barebox_arm_entry(0x80000000, SZ_512M, fdt - get_runtime_offset());
+}
diff --git a/arch/arm/configs/zii_vf610_dev_defconfig b/arch/arm/configs/zii_vf610_dev_defconfig
new file mode 100644
index 0000000..bda6044
--- /dev/null
+++ b/arch/arm/configs/zii_vf610_dev_defconfig
@@ -0,0 +1,165 @@
+CONFIG_ARCH_IMX=y
+CONFIG_IMX_MULTI_BOARDS=y
+CONFIG_MACH_SABRESD=y
+CONFIG_MACH_ZII_VF610_DEV=y
+CONFIG_IMX_IIM=y
+CONFIG_IMX_IIM_FUSE_BLOW=y
+CONFIG_THUMB2_BAREBOX=y
+CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y
+CONFIG_ARM_UNWIND=y
+CONFIG_MMU=y
+CONFIG_TEXT_BASE=0x0
+CONFIG_MALLOC_SIZE=0x0
+CONFIG_MALLOC_TLSF=y
+CONFIG_KALLSYMS=y
+CONFIG_RELOCATABLE=y
+CONFIG_HUSH_FANCY_PROMPT=y
+CONFIG_CMDLINE_EDITING=y
+CONFIG_AUTO_COMPLETE=y
+CONFIG_MENU=y
+CONFIG_BOOTM_SHOW_TYPE=y
+CONFIG_BOOTM_VERBOSE=y
+CONFIG_BOOTM_INITRD=y
+CONFIG_BOOTM_OFTREE=y
+CONFIG_BOOTM_OFTREE_UIMAGE=y
+CONFIG_BLSPEC=y
+CONFIG_PARTITION_DISK_EFI=y
+CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW=y
+CONFIG_RESET_SOURCE=y
+CONFIG_CMD_DMESG=y
+CONFIG_LONGHELP=y
+CONFIG_CMD_IOMEM=y
+CONFIG_CMD_IMD=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_ARM_MMUINFO=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_MMC_EXTCSD=y
+# CONFIG_CMD_BOOTU is not set
+CONFIG_CMD_GO=y
+CONFIG_CMD_RESET=y
+CONFIG_CMD_UIMAGE=y
+CONFIG_CMD_PARTITION=y
+CONFIG_CMD_UBIFORMAT=y
+CONFIG_CMD_EXPORT=y
+CONFIG_CMD_LOADENV=y
+CONFIG_CMD_PRINTENV=y
+CONFIG_CMD_MAGICVAR=y
+CONFIG_CMD_MAGICVAR_HELP=y
+CONFIG_CMD_SAVEENV=y
+CONFIG_CMD_FILETYPE=y
+CONFIG_CMD_LN=y
+CONFIG_CMD_MD5SUM=y
+CONFIG_CMD_UNCOMPRESS=y
+CONFIG_CMD_LET=y
+CONFIG_CMD_MSLEEP=y
+CONFIG_CMD_READF=y
+CONFIG_CMD_SLEEP=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MIITOOL=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_TFTP=y
+CONFIG_CMD_ECHO_E=y
+CONFIG_CMD_EDIT=y
+CONFIG_CMD_MENU=y
+CONFIG_CMD_MENU_MANAGEMENT=y
+CONFIG_CMD_MENUTREE=y
+CONFIG_CMD_SPLASH=y
+CONFIG_CMD_READLINE=y
+CONFIG_CMD_TIMEOUT=y
+CONFIG_CMD_CRC=y
+CONFIG_CMD_CRC_CMP=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_MM=y
+CONFIG_CMD_CLK=y
+CONFIG_CMD_DETECT=y
+CONFIG_CMD_FLASH=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_LED=y
+CONFIG_CMD_NANDTEST=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_LED_TRIGGER=y
+CONFIG_CMD_USBGADGET=y
+CONFIG_CMD_WD=y
+CONFIG_CMD_BAREBOX_UPDATE=y
+CONFIG_CMD_OF_NODE=y
+CONFIG_CMD_OF_PROPERTY=y
+CONFIG_CMD_OFTREE=y
+CONFIG_CMD_TIME=y
+CONFIG_NET=y
+CONFIG_NET_NETCONSOLE=y
+CONFIG_NET_RESOLV=y
+CONFIG_OF_BAREBOX_DRIVERS=y
+CONFIG_DRIVER_NET_FEC_IMX=y
+CONFIG_AT803X_PHY=y
+CONFIG_MICREL_PHY=y
+CONFIG_NET_USB=y
+CONFIG_NET_USB_ASIX=y
+CONFIG_NET_USB_SMSC95XX=y
+CONFIG_DRIVER_SPI_IMX=y
+CONFIG_DRIVER_SPI_DSPI=y
+CONFIG_I2C=y
+CONFIG_I2C_IMX=y
+CONFIG_MTD=y
+CONFIG_MTD_RAW_DEVICE=y
+CONFIG_MTD_DATAFLASH=y
+CONFIG_MTD_M25P80=y
+CONFIG_MTD_SST25L=y
+CONFIG_NAND=y
+CONFIG_NAND_ALLOW_ERASE_BAD=y
+CONFIG_NAND_IMX=y
+CONFIG_NAND_IMX_BBM=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_FASTMAP=y
+CONFIG_DISK_AHCI=y
+CONFIG_DISK_AHCI_IMX=y
+CONFIG_DISK_INTF_PLATFORM_IDE=y
+CONFIG_DISK_PATA_IMX=y
+CONFIG_USB_HOST=y
+CONFIG_USB_IMX_CHIPIDEA=y
+CONFIG_USB_EHCI=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_DFU=y
+CONFIG_USB_GADGET_SERIAL=y
+CONFIG_USB_GADGET_FASTBOOT=y
+CONFIG_VIDEO=y
+CONFIG_DRIVER_VIDEO_IMX_IPUV3=y
+CONFIG_DRIVER_VIDEO_IMX_IPUV3_LVDS=y
+CONFIG_DRIVER_VIDEO_IMX_IPUV3_HDMI=y
+CONFIG_DRIVER_VIDEO_SIMPLEFB=y
+CONFIG_DRIVER_VIDEO_EDID=y
+CONFIG_MCI=y
+CONFIG_MCI_MMC_BOOT_PARTITIONS=y
+CONFIG_MCI_IMX_ESDHC=y
+CONFIG_MFD_MC13XXX=y
+CONFIG_MFD_MC34704=y
+CONFIG_MFD_MC9SDZ60=y
+CONFIG_MFD_STMPE=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_LED_GPIO_OF=y
+CONFIG_LED_TRIGGERS=y
+CONFIG_EEPROM_AT25=y
+CONFIG_EEPROM_AT24=y
+CONFIG_KEYBOARD_GPIO=y
+CONFIG_WATCHDOG=y
+CONFIG_WATCHDOG_IMX=y
+CONFIG_PWM=y
+CONFIG_PWM_IMX=y
+CONFIG_GPIO_STMPE=y
+CONFIG_GPIO_SX150X=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED=y
+CONFIG_GENERIC_PHY=y
+CONFIG_USB_NOP_XCEIV=y
+CONFIG_FS_EXT4=y
+CONFIG_FS_TFTP=y
+CONFIG_FS_NFS=y
+CONFIG_FS_FAT=y
+CONFIG_FS_FAT_WRITE=y
+CONFIG_FS_FAT_LFN=y
+CONFIG_FS_UBIFS=y
+CONFIG_FS_UBIFS_COMPRESSION_LZO=y
+CONFIG_PNG=y
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index f5fb0cd..cfb7b95 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -81,5 +81,12 @@ pbl-dtb-$(CONFIG_MACH_VARISCITE_MX6) += imx6q-var-custom.dtb.o
pbl-dtb-$(CONFIG_MACH_VSCOM_BALTOS) += am335x-baltos-minimal.dtb.o
pbl-dtb-$(CONFIG_MACH_VF610_TWR) += vf610-twr.dtb.o
pbl-dtb-$(CONFIG_MACH_ZII_RDU2) += imx6q-zii-rdu2.dtb.o imx6qp-zii-rdu2.dtb.o
+pbl-dtb-$(CONFIG_MACH_ZII_VF610_DEV) += \
+ vf610-zii-dev-rev-b.dtb.o \
+ vf610-zii-dev-rev-c.dtb.o \
+ vf610-zii-cfu1-rev-a.dtb.o \
+ vf610-zii-spu3-rev-a.dtb.o \
+ vf610-zii-scu4-aib-rev-c.dtb.o
+
clean-files := *.dtb *.dtb.S .*.dtc .*.pre .*.dts *.dtb.lzo
diff --git a/arch/arm/dts/vf610-zii-cfu1-rev-a.dts b/arch/arm/dts/vf610-zii-cfu1-rev-a.dts
new file mode 100644
index 0000000..4147d13
--- /dev/null
+++ b/arch/arm/dts/vf610-zii-cfu1-rev-a.dts
@@ -0,0 +1,208 @@
+/*
+ * Copyright (C) 2015, 2016 Zodiac Inflight Innovations
+ *
+ * Based on an original 'vf610-twr.dts' which is Copyright 2015,
+ * Freescale Semiconductor, Inc.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+
+
+/dts-v1/;
+#include "vf610-zii-dev.dtsi"
+
+/ {
+ model = "ZII VF610 CFU1 Switch Management Board";
+ compatible = "zii,vf610cfu1-a", "zii,vf610dev", "fsl,vf610";
+
+ aliases {
+ /delete-property/ serial1;
+ /delete-property/ serial2;
+ };
+
+ gpio-leds {
+ debug {
+ gpios = <&gpio2 18 GPIO_ACTIVE_HIGH>;
+ };
+
+ fail {
+ label = "zii_fail";
+ gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ max-brightness = <1>;
+ };
+
+ status {
+ label = "zii_status";
+ gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ max-brightness = <1>;
+ };
+
+ status_a {
+ label = "zii_status_a";
+ gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ max-brightness = <1>;
+ };
+
+ status_b {
+ label = "zii_status_b";
+ gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ max-brightness = <1>;
+ };
+ };
+};
+
+&dspi1 {
+ bus-num = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_dspi1>;
+ status = "okay";
+
+ m25p128@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p128", "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+
+ partition@0 {
+ label = "m25p128-0";
+ reg = <0x0 0x01000000>;
+ };
+ };
+};
+
+&esdhc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_esdhc0>;
+ bus-width = <8>;
+ status = "okay";
+};
+
+&fec0 {
+ status = "disabled";
+};
+
+&i2c0 {
+ clock-frequency = <400000>;
+
+ pca9554@22 {
+ compatible = "nxp,pca9554";
+ reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
+
+/delete-node/ &i2c1;
+/delete-node/ &i2c2;
+/delete-node/ &uart1;
+/delete-node/ &uart2;
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ VF610_PAD_PTE2__GPIO_107 0x31c2 /* SOC_SW_RSTn */
+ VF610_PAD_PTB28__GPIO_98 0x31c1 /* E6352_INTn */
+
+ /* PTE27 is wired to signal SD on part CONN
+ * SFF-F4 via net FIM_DS. An active high
+ * on this indicates a received optical
+ * signal
+
+ * SPEED=0b11 HIGH, SRE=0b0, ODE=0b0, HYS=0b0
+ * DSE=0b001 150Ohm, PUS=0b10 100k UP
+ * PKE=0b0, PUE=0b0, OBE=0b0, IBE=0b1
+ */
+ VF610_PAD_PTE27__GPIO_132 0x3061
+
+ /*
+ * PTE13 is wired to signal T_DIS on part CONN
+ * SFF-F4 via net FIM_TDIS. Setting this high
+ * will disable optical output from the SFF-F4
+
+ * SPEED=0b11 HIGH, SRE=0b0, ODE=0b0, HYS=0b0
+ * DSE=0b001 150Ohm, PUS=0b00 100k DOWN
+ * PKE=0b0, PUE=0b0, OBE=0b1, IBE=0b1
+ * TODO: probably want IBE=0b0
+ */
+ VF610_PAD_PTE13__GPIO_118 0x3043
+ >;
+ };
+
+ pinctrl_dspi1: dspi1grp {
+ fsl,pins = <
+ VF610_PAD_PTD5__DSPI1_CS0 0x1182
+ VF610_PAD_PTC6__DSPI1_SIN 0x1181
+ VF610_PAD_PTC7__DSPI1_SOUT 0x1182
+ VF610_PAD_PTC8__DSPI1_SCK 0x1182
+ >;
+ };
+
+ pinctrl_esdhc0: esdhc0grp {
+ fsl,pins = <
+ VF610_PAD_PTC0__ESDHC0_CLK 0x31ef
+ VF610_PAD_PTC1__ESDHC0_CMD 0x31ef
+ VF610_PAD_PTC2__ESDHC0_DAT0 0x31ef
+ VF610_PAD_PTC3__ESDHC0_DAT1 0x31ef
+ VF610_PAD_PTC4__ESDHC0_DAT2 0x31ef
+ VF610_PAD_PTC5__ESDHC0_DAT3 0x31ef
+ VF610_PAD_PTD23__ESDHC0_DAT4 0x31ef
+ VF610_PAD_PTD22__ESDHC0_DAT5 0x31ef
+ VF610_PAD_PTD21__ESDHC0_DAT6 0x31ef
+ VF610_PAD_PTD20__ESDHC0_DAT7 0x31ef
+ >;
+ };
+
+ pinctrl_leds_debug: pinctrl-leds-debug {
+ fsl,pins = <
+ VF610_PAD_PTD3__GPIO_82 0x31c2
+ VF610_PAD_PTE3__GPIO_108 0x31c2
+ VF610_PAD_PTE4__GPIO_109 0x31c2
+ VF610_PAD_PTE5__GPIO_110 0x31c2
+ VF610_PAD_PTE6__GPIO_111 0x31c2
+ >;
+ };
+};
diff --git a/arch/arm/dts/vf610-zii-dev-rev-b.dts b/arch/arm/dts/vf610-zii-dev-rev-b.dts
new file mode 100644
index 0000000..bf0a010
--- /dev/null
+++ b/arch/arm/dts/vf610-zii-dev-rev-b.dts
@@ -0,0 +1,431 @@
+/*
+ * Copyright (C) 2015, 2016 Zodiac Inflight Innovations
+ *
+ * Based on an original 'vf610-twr.dts' which is Copyright 2015,
+ * Freescale Semiconductor, Inc.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "vf610-zii-dev.dtsi"
+
+/*
+ * =============================================================
+ * The following code is shared with Linux kernel and should be
+ * removed once it trickles down from there eventually
+ * =============================================================
+ */
+
+/ {
+ model = "ZII VF610 Development Board, Rev B";
+ compatible = "zii,vf610dev-b", "zii,vf610dev", "fsl,vf610";
+
+ mdio-mux {
+ compatible = "mdio-mux-gpio";
+ pinctrl-0 = <&pinctrl_mdio_mux>;
+ pinctrl-names = "default";
+ gpios = <&gpio0 8 GPIO_ACTIVE_HIGH
+ &gpio0 9 GPIO_ACTIVE_HIGH
+ &gpio0 24 GPIO_ACTIVE_HIGH
+ &gpio0 25 GPIO_ACTIVE_HIGH>;
+ mdio-parent-bus = <&mdio1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio_mux_1: mdio@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch0: switch0@0 {
+ compatible = "marvell,mv88e6085";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ dsa,member = <0 0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ label = "lan0";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ };
+
+ switch0port5: port@5 {
+ reg = <5>;
+ label = "dsa";
+ phy-mode = "rgmii-txid";
+ link = <&switch1port6
+ &switch2port9>;
+ };
+
+ port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&fec1>;
+ fixed-link {
+ speed = <100>;
+ full-duplex;
+ };
+ };
+ };
+ };
+ };
+
+ mdio_mux_2: mdio@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch1: switch1@0 {
+ compatible = "marvell,mv88e6085";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ dsa,member = <0 1>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ label = "lan3";
+ phy-handle = <&switch1phy0>;
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan4";
+ phy-handle = <&switch1phy1>;
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan5";
+ phy-handle = <&switch1phy2>;
+ };
+
+ switch1port5: port@5 {
+ reg = <5>;
+ label = "dsa";
+ link = <&switch2port9>;
+ phy-mode = "rgmii-txid";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ switch1port6: port@6 {
+ reg = <6>;
+ label = "dsa";
+ phy-mode = "rgmii-txid";
+ link = <&switch0port5>;
+ };
+ };
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ switch1phy0: switch1phy0@0 {
+ reg = <0>;
+ };
+ switch1phy1: switch1phy0@1 {
+ reg = <1>;
+ };
+ switch1phy2: switch1phy0@2 {
+ reg = <2>;
+ };
+ };
+ };
+ };
+
+ mdio_mux_4: mdio@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+
+ switch2: switch2@0 {
+ compatible = "marvell,mv88e6085";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ dsa,member = <0 2>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ label = "lan6";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan7";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan8";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "optical3";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ link-gpios = <&gpio6 2
+ GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "optical4";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ link-gpios = <&gpio6 3
+ GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ switch2port9: port@9 {
+ reg = <9>;
+ label = "dsa";
+ phy-mode = "rgmii-txid";
+ link = <&switch1port5
+ &switch0port5>;
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+ };
+
+ mdio_mux_8: mdio@8 {
+ reg = <8>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ spi0 {
+ compatible = "spi-gpio";
+ pinctrl-0 = <&pinctrl_gpio_spi0>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-sck = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+ gpio-mosi = <&gpio1 11 GPIO_ACTIVE_HIGH>;
+ gpio-miso = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH
+ &gpio1 8 GPIO_ACTIVE_HIGH>;
+ num-chipselects = <2>;
+
+ m25p128@0 {
+ compatible = "m25p128", "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0>;
+ spi-max-frequency = <1000000>;
+ };
+
+ at93c46d@1 {
+ compatible = "atmel,at93c46d";
+ pinctrl-0 = <&pinctrl_gpio_e6185_eeprom_sel>;
+ pinctrl-names = "default";
+ #address-cells = <0>;
+ #size-cells = <0>;
+ reg = <1>;
+ spi-max-frequency = <500000>;
+ spi-cs-high;
+ data-size = <16>;
+ select-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&i2c0 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c0>;
+ status = "okay";
+
+ gpio5: pca9554@20 {
+ compatible = "nxp,pca9554";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ };
+
+ gpio6: pca9554@22 {
+ compatible = "nxp,pca9554";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pca9554_22>;
+ reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+
+ tca9548@70 {
+ compatible = "nxp,pca9548";
+ pinctrl-0 = <&pinctrl_i2c_mux_reset>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x70>;
+ reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ sfp1: at24c04@50 {
+ compatible = "atmel,24c02";
+ reg = <0x50>;
+ };
+ };
+
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ sfp2: at24c04@50 {
+ compatible = "atmel,24c02";
+ reg = <0x50>;
+ };
+ };
+
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+
+ sfp3: at24c04@50 {
+ compatible = "atmel,24c02";
+ reg = <0x50>;
+ };
+ };
+
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+
+ sfp4: at24c04@50 {
+ compatible = "atmel,24c02";
+ reg = <0x50>;
+ };
+ };
+
+ i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+ };
+};
+
+
+&iomuxc {
+ pinctrl_gpio_e6185_eeprom_sel: pinctrl-gpio-e6185-eeprom-spi0 {
+ fsl,pins = <
+ VF610_PAD_PTE27__GPIO_132 0x33e2
+ >;
+ };
+
+ pinctrl_gpio_spi0: pinctrl-gpio-spi0 {
+ fsl,pins = <
+ VF610_PAD_PTB22__GPIO_44 0x33e2
+ VF610_PAD_PTB21__GPIO_43 0x33e2
+ VF610_PAD_PTB20__GPIO_42 0x33e1
+ VF610_PAD_PTB19__GPIO_41 0x33e2
+ VF610_PAD_PTB18__GPIO_40 0x33e2
+ >;
+ };
+
+ pinctrl_mdio_mux: pinctrl-mdio-mux {
+ fsl,pins = <
+ VF610_PAD_PTA18__GPIO_8 0x31c2
+ VF610_PAD_PTA19__GPIO_9 0x31c2
+ VF610_PAD_PTB2__GPIO_24 0x31c2
+ VF610_PAD_PTB3__GPIO_25 0x31c2
+ >;
+ };
+
+ pinctrl_pca9554_22: pinctrl-pca95540-22 {
+ fsl,pins = <
+ VF610_PAD_PTB28__GPIO_98 0x219d
+ >;
+ };
+};
+
+/*
+ * =============================================================
+ * End of shared part
+ * =============================================================
+*/
diff --git a/arch/arm/dts/vf610-zii-dev-rev-c.dts b/arch/arm/dts/vf610-zii-dev-rev-c.dts
new file mode 100644
index 0000000..5228942
--- /dev/null
+++ b/arch/arm/dts/vf610-zii-dev-rev-c.dts
@@ -0,0 +1,445 @@
+/*
+ * Copyright (C) 2015, 2016 Zodiac Inflight Innovations
+ *
+ * Based on an original 'vf610-twr.dts' which is Copyright 2015,
+ * Freescale Semiconductor, Inc.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "vf610-zii-dev.dtsi"
+
+/*
+ * =============================================================
+ * The following code is shared with Linux kernel and should be
+ * removed once it trickles down from there eventually
+ * =============================================================
+ */
+
+/ {
+ model = "ZII VF610 Development Board, Rev C";
+ compatible = "zii,vf610dev-c", "zii,vf610dev", "fsl,vf610";
+
+ mdio-mux {
+ compatible = "mdio-mux-gpio";
+ pinctrl-0 = <&pinctrl_mdio_mux>;
+ pinctrl-names = "default";
+ gpios = <&gpio0 8 GPIO_ACTIVE_HIGH
+ &gpio0 9 GPIO_ACTIVE_HIGH
+ &gpio0 25 GPIO_ACTIVE_HIGH>;
+ mdio-parent-bus = <&mdio1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio_mux_1: mdio@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch0: switch0@0 {
+ compatible = "marvell,mv88e6190";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ dsa,member = <0 0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "cpu";
+ ethernet = <&fec1>;
+ fixed-link {
+ speed = <100>;
+ full-duplex;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan3";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "lan4";
+ };
+
+ switch0port10: port@10 {
+ reg = <10>;
+ label = "dsa";
+ phy-mode = "xgmii";
+ link = <&switch1port10>;
+ };
+ };
+ };
+ };
+
+ mdio_mux_2: mdio@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch1: switch1@0 {
+ compatible = "marvell,mv88e6190";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ dsa,member = <0 1>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+ label = "lan5";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan6";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan7";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "lan8";
+ };
+
+
+ switch1port10: port@10 {
+ reg = <10>;
+ label = "dsa";
+ phy-mode = "xgmii";
+ link = <&switch0port10>;
+ };
+ };
+ };
+ };
+
+ mdio_mux_4: mdio@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+};
+
+&dspi0 {
+ bus-num = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_dspi0>;
+ status = "okay";
+ spi-num-chipselects = <2>;
+
+ m25p128@0 {
+ compatible = "m25p128", "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ };
+
+ atzb-rf-233@1 {
+ compatible = "atmel,at86rf233";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctr_atzb_rf_233>;
+
+ spi-max-frequency = <7500000>;
+ reg = <1>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gpio3>;
+ xtal-trim = /bits/ 8 <0x06>;
+
+ sleep-gpio = <&gpio0 24 GPIO_ACTIVE_HIGH>;
+ reset-gpio = <&gpio6 10 GPIO_ACTIVE_HIGH>;
+
+ fsl,spi-cs-sck-delay = <180>;
+ fsl,spi-sck-cs-delay = <250>;
+ };
+};
+
+&dspi2 {
+ bus-num = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_dspi2>;
+ status = "okay";
+ spi-num-chipselects = <2>;
+};
+
+&i2c0 {
+ /*
+ * U712
+ *
+ * Exposed signals:
+ * P1 - WE2_CMD
+ * P2 - WE2_CLK
+ */
+ gpio5: pca9557@18 {
+ compatible = "nxp,pca9557";
+ reg = <0x18>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ /*
+ * U121
+ *
+ * Exposed signals:
+ * I/O0 - ENET_SWR_EN
+ * I/O1 - ESW1_RESETn
+ * I/O2 - ARINC_RESET
+ * I/O3 - DD1_IO_RESET
+ * I/O4 - ESW2_RESETn
+ * I/O5 - ESW3_RESETn
+ * I/O6 - ESW4_RESETn
+ * I/O8 - TP909
+ * I/O9 - FEM_SEL
+ * I/O10 - WIFI_RESETn
+ * I/O11 - PHY_RSTn
+ * I/O12 - OPT1_SD
+ * I/O13 - OPT2_SD
+ * I/O14 - OPT1_TX_DIS
+ * I/O15 - OPT2_TX_DIS
+ */
+ gpio6: sx1503@20 {
+ compatible = "semtech,sx1503q";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sx1503_20>;
+ #gpio-cells = <2>;
+ #interrupt-cells = <2>;
+ reg = <0x20>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
+ gpio-controller;
+ interrupt-controller;
+
+ enet_swr_en {
+ gpio-hog;
+ gpios = <0 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "enet-swr-en";
+ };
+ };
+
+ /*
+ * U715
+ *
+ * Exposed signals:
+ * IO0 - WE1_CLK
+ * IO1 - WE1_CMD
+ */
+ gpio7: pca9554@22 {
+ compatible = "nxp,pca9554";
+ reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ };
+};
+
+&i2c1 {
+ at24mac602@00 {
+ compatible = "atmel,24c02";
+ reg = <0x50>;
+ read-only;
+ };
+};
+
+&i2c2 {
+ tca9548@70 {
+ compatible = "nxp,pca9548";
+ pinctrl-0 = <&pinctrl_i2c_mux_reset>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x70>;
+ reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ sfp2: at24c04@50 {
+ compatible = "atmel,24c02";
+ reg = <0x50>;
+ };
+ };
+
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+
+ sfp3: at24c04@50 {
+ compatible = "atmel,24c02";
+ reg = <0x50>;
+ };
+ };
+
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&gpio0 {
+ eth0_intrp {
+ gpio-hog;
+ gpios = <23 GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "sx1503-irq";
+ };
+};
+
+&gpio3 {
+ eth0_intrp {
+ gpio-hog;
+ gpios = <2 GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "eth0-intrp";
+ };
+};
+
+&fec0 {
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec0_phy_int>;
+
+ interrupt-parent = <&gpio3>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+ reg = <0>;
+ };
+ };
+};
+
+&iomuxc {
+ pinctr_atzb_rf_233: pinctrl-atzb-rf-233 {
+ fsl,pins = <
+ VF610_PAD_PTB2__GPIO_24 0x31c2
+ VF610_PAD_PTE27__GPIO_132 0x33e2
+ >;
+ };
+
+
+ pinctrl_sx1503_20: pinctrl-sx1503-20 {
+ fsl,pins = <
+ VF610_PAD_PTB1__GPIO_23 0x219d
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ VF610_PAD_PTA20__UART3_TX 0x21a2
+ VF610_PAD_PTA21__UART3_RX 0x21a1
+ >;
+ };
+
+ pinctrl_mdio_mux: pinctrl-mdio-mux {
+ fsl,pins = <
+ VF610_PAD_PTA18__GPIO_8 0x31c2
+ VF610_PAD_PTA19__GPIO_9 0x31c2
+ VF610_PAD_PTB3__GPIO_25 0x31c2
+ >;
+ };
+
+ pinctrl_fec0_phy_int: pinctrl-fec0-phy-int {
+ fsl,pins = <
+ VF610_PAD_PTB28__GPIO_98 0x219d
+ >;
+ };
+};
+
+/*
+ * =============================================================
+ * End of shared part
+ * =============================================================
+ */
+
+
+&dspi0 {
+ m25p128@0 {
+ partition@0 {
+ label = "bootloader";
+ reg = <0x0 0x100000>;
+ };
+ };
+};
diff --git a/arch/arm/dts/vf610-zii-dev.dtsi b/arch/arm/dts/vf610-zii-dev.dtsi
new file mode 100644
index 0000000..dae077c
--- /dev/null
+++ b/arch/arm/dts/vf610-zii-dev.dtsi
@@ -0,0 +1,436 @@
+/*
+ * Copyright (C) 2015, 2016 Zodiac Inflight Innovations
+ *
+ * Based on an original 'vf610-twr.dts' which is Copyright 2015,
+ * Freescale Semiconductor, Inc.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+n * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+
+/*
+ * =============================================================
+ * The following code is shared with Linux kernel and should be
+ * removed once it trickles down from there eventually
+ * =============================================================
+ */
+
+#include <arm/vf610.dtsi>
+
+/ {
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ reg = <0x80000000 0x20000000>;
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&pinctrl_leds_debug>;
+ pinctrl-names = "default";
+
+ debug {
+ label = "zii:green:debug1";
+ gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ reg_vcc_3v3_mcu: regulator-vcc-3v3-mcu {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_3v3_mcu";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ usb0_vbus: regulator-usb0-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-0 = <&pinctrl_usb_vbus>;
+ regulator-name = "usb_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 6 0>;
+ };
+};
+
+&adc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc0_ad5>;
+ vref-supply = <®_vcc_3v3_mcu>;
+ status = "okay";
+};
+
+&edma0 {
+ status = "okay";
+};
+
+&esdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_esdhc1>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&fec0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec0>;
+ status = "okay";
+};
+
+&fec1 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec1>;
+ status = "okay";
+
+ fixed-link {
+ speed = <100>;
+ full-duplex;
+ };
+
+ mdio1: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+ };
+};
+
+&i2c0 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c0>;
+ pinctrl-1 = <&pinctrl_i2c0_gpio>;
+ scl-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ lm75@48 {
+ compatible = "national,lm75";
+ reg = <0x48>;
+ };
+
+ at24c04@50 {
+ compatible = "atmel,24c04";
+ reg = <0x50>;
+ };
+
+ at24c04@52 {
+ compatible = "atmel,24c04";
+ reg = <0x52>;
+ };
+
+ ds1682@6b {
+ compatible = "dallas,ds1682";
+ reg = <0x6b>;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&usbdev0 {
+ disable-over-current;
+ vbus-supply = <&usb0_vbus>;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbh1 {
+ disable-over-current;
+ status = "okay";
+};
+
+&usbmisc0 {
+ status = "okay";
+};
+
+&usbmisc1 {
+ status = "okay";
+};
+
+&usbphy0 {
+ status = "okay";
+};
+
+&usbphy1 {
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_adc0_ad5: adc0ad5grp {
+ fsl,pins = <
+ VF610_PAD_PTC30__ADC0_SE5 0x00a1
+ >;
+ };
+
+ pinctrl_dspi0: dspi0grp {
+ fsl,pins = <
+ VF610_PAD_PTB18__DSPI0_CS1 0x1182
+ VF610_PAD_PTB19__DSPI0_CS0 0x1182
+ VF610_PAD_PTB20__DSPI0_SIN 0x1181
+ VF610_PAD_PTB21__DSPI0_SOUT 0x1182
+ VF610_PAD_PTB22__DSPI0_SCK 0x1182
+ >;
+ };
+
+ pinctrl_dspi2: dspi2grp {
+ fsl,pins = <
+ VF610_PAD_PTD31__DSPI2_CS1 0x1182
+ VF610_PAD_PTD30__DSPI2_CS0 0x1182
+ VF610_PAD_PTD29__DSPI2_SIN 0x1181
+ VF610_PAD_PTD28__DSPI2_SOUT 0x1182
+ VF610_PAD_PTD27__DSPI2_SCK 0x1182
+ >;
+ };
+
+ pinctrl_esdhc1: esdhc1grp {
+ fsl,pins = <
+ VF610_PAD_PTA24__ESDHC1_CLK 0x31ef
+ VF610_PAD_PTA25__ESDHC1_CMD 0x31ef
+ VF610_PAD_PTA26__ESDHC1_DAT0 0x31ef
+ VF610_PAD_PTA27__ESDHC1_DAT1 0x31ef
+ VF610_PAD_PTA28__ESDHC1_DATA2 0x31ef
+ VF610_PAD_PTA29__ESDHC1_DAT3 0x31ef
+ VF610_PAD_PTA7__GPIO_134 0x219d
+ >;
+ };
+
+ pinctrl_fec0: fec0grp {
+ fsl,pins = <
+ VF610_PAD_PTC0__ENET_RMII0_MDC 0x30d2
+ VF610_PAD_PTC1__ENET_RMII0_MDIO 0x30d3
+ VF610_PAD_PTC2__ENET_RMII0_CRS 0x30d1
+ VF610_PAD_PTC3__ENET_RMII0_RXD1 0x30d1
+ VF610_PAD_PTC4__ENET_RMII0_RXD0 0x30d1
+ VF610_PAD_PTC5__ENET_RMII0_RXER 0x30d1
+ VF610_PAD_PTC6__ENET_RMII0_TXD1 0x30d2
+ VF610_PAD_PTC7__ENET_RMII0_TXD0 0x30d2
+ VF610_PAD_PTC8__ENET_RMII0_TXEN 0x30d2
+ >;
+ };
+
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ VF610_PAD_PTA6__RMII_CLKIN 0x30d1
+ VF610_PAD_PTC9__ENET_RMII1_MDC 0x30d2
+ VF610_PAD_PTC10__ENET_RMII1_MDIO 0x30d3
+ VF610_PAD_PTC11__ENET_RMII1_CRS 0x30d1
+ VF610_PAD_PTC12__ENET_RMII1_RXD1 0x30d1
+ VF610_PAD_PTC13__ENET_RMII1_RXD0 0x30d1
+ VF610_PAD_PTC14__ENET_RMII1_RXER 0x30d1
+ VF610_PAD_PTC15__ENET_RMII1_TXD1 0x30d2
+ VF610_PAD_PTC16__ENET_RMII1_TXD0 0x30d2
+ VF610_PAD_PTC17__ENET_RMII1_TXEN 0x30d2
+ >;
+ };
+
+ pinctrl_gpio_spi0: pinctrl-gpio-spi0 {
+ fsl,pins = <
+ VF610_PAD_PTB22__GPIO_44 0x33e2
+ VF610_PAD_PTB21__GPIO_43 0x33e2
+ VF610_PAD_PTB20__GPIO_42 0x33e1
+ VF610_PAD_PTB19__GPIO_41 0x33e2
+ VF610_PAD_PTB18__GPIO_40 0x33e2
+ >;
+ };
+
+ pinctrl_i2c_mux_reset: pinctrl-i2c-mux-reset {
+ fsl,pins = <
+ VF610_PAD_PTE14__GPIO_119 0x31c2
+ >;
+ };
+
+ pinctrl_i2c0: i2c0grp {
+ fsl,pins = <
+ VF610_PAD_PTB14__I2C0_SCL 0x37ff
+ VF610_PAD_PTB15__I2C0_SDA 0x37ff
+ >;
+ };
+
+ pinctrl_i2c0_gpio: i2c0grp-gpio {
+ fsl,pins = <
+ VF610_PAD_PTB14__GPIO_36 0x31c2
+ VF610_PAD_PTB15__GPIO_37 0x31c2
+ >;
+ };
+
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ VF610_PAD_PTB16__I2C1_SCL 0x37ff
+ VF610_PAD_PTB17__I2C1_SDA 0x37ff
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ VF610_PAD_PTA22__I2C2_SCL 0x37ff
+ VF610_PAD_PTA23__I2C2_SDA 0x37ff
+ >;
+ };
+
+ pinctrl_leds_debug: pinctrl-leds-debug {
+ fsl,pins = <
+ VF610_PAD_PTD20__GPIO_74 0x31c2
+ >;
+ };
+
+ pinctrl_qspi0: qspi0grp {
+ fsl,pins = <
+ VF610_PAD_PTD7__QSPI0_B_QSCK 0x31c3
+ VF610_PAD_PTD8__QSPI0_B_CS0 0x31ff
+ VF610_PAD_PTD9__QSPI0_B_DATA3 0x31c3
+ VF610_PAD_PTD10__QSPI0_B_DATA2 0x31c3
+ VF610_PAD_PTD11__QSPI0_B_DATA1 0x31c3
+ VF610_PAD_PTD12__QSPI0_B_DATA0 0x31c3
+ >;
+ };
+
+ pinctrl_uart0: uart0grp {
+ fsl,pins = <
+ VF610_PAD_PTB10__UART0_TX 0x21a2
+ VF610_PAD_PTB11__UART0_RX 0x21a1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ VF610_PAD_PTB23__UART1_TX 0x21a2
+ VF610_PAD_PTB24__UART1_RX 0x21a1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ VF610_PAD_PTD0__UART2_TX 0x21a2
+ VF610_PAD_PTD1__UART2_RX 0x21a1
+ >;
+ };
+
+ pinctrl_usb_vbus: pinctrl-usb-vbus {
+ fsl,pins = <
+ VF610_PAD_PTA16__GPIO_6 0x31c2
+ >;
+ };
+
+ pinctrl_usb0_host: usb0-host-grp {
+ fsl,pins = <
+ VF610_PAD_PTD6__GPIO_85 0x0062
+ >;
+ };
+};
+
+/*
+ * =============================================================
+ * End of shared part
+ * =============================================================
+ */
+
+/ {
+ audio_ext: mclk_osc {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ };
+
+ enet_ext: eth_osc {
+ compatible = "fixed-clock";
+ clock-output-names = "enet_ext";
+ #clock-cells = <0>;
+ clock-frequency = <50000000>;
+ };
+
+ anaclk1: anaclk1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ };
+};
+
+&clks {
+ clocks = <&sxosc>, <&fxosc>, <&enet_ext>, <&audio_ext>, <&anaclk1>,
+ <&clks VF610_CLK_SYS_BUS>, <&clks VF610_CLK_PLATFORM_BUS>,
+ <&clks VF610_CLK_IPG_BUS>, <&clks VF610_CLK_DDRMC>;
+ clock-names = "sxosc", "fxosc", "enet_ext", "audio_ext", "anaclk1",
+ "cpu", "bus", "ipg", "ddr";
+
+ assigned-clocks = <&clks VF610_CLK_ENET_SEL>,
+ <&clks VF610_CLK_ENET_TS_SEL>;
+ assigned-clock-parents = <&clks VF610_CLK_ENET_EXT>,
+ <&clks VF610_CLK_ENET_EXT>;
+};
+
+&ocotp {
+ barebox,provide-mac-address = <&fec0 0x620>,
+ <&fec1 0x640>;
+};
diff --git a/arch/arm/dts/vf610-zii-scu4-aib-rev-c.dts b/arch/arm/dts/vf610-zii-scu4-aib-rev-c.dts
new file mode 100644
index 0000000..d10f460
--- /dev/null
+++ b/arch/arm/dts/vf610-zii-scu4-aib-rev-c.dts
@@ -0,0 +1,457 @@
+/*
+ * Copyright (C) 2015, 2016 Zodiac Inflight Innovations
+ *
+ * Based on an original 'vf610-twr.dts' which is Copyright 2015,
+ * Freescale Semiconductor, Inc.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "vf610-zii-dev.dtsi"
+
+/ {
+ model = "ZII VF610 SCU4 AIB, Rev C";
+ compatible = "zii,vf610scu4-aib-c", "zii,vf610dev", "fsl,vf610";
+
+ chosen {
+ bootargs = "console=ttyLP0,115200n8";
+ };
+
+ gpio-leds {
+ debug {
+ gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ mdio-mux {
+ compatible = "mdio-mux-gpio";
+ pinctrl-0 = <&pinctrl_mdio_mux>;
+ pinctrl-names = "default";
+ gpios = <&gpio4 4 GPIO_ACTIVE_HIGH
+ &gpio4 5 GPIO_ACTIVE_HIGH
+ &gpio3 30 GPIO_ACTIVE_HIGH
+ &gpio3 31 GPIO_ACTIVE_HIGH>;
+ mdio-parent-bus = <&mdio1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio_mux_1: mdio@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mdio_mux_2: mdio@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mdio_mux_4: mdio@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mdio_mux_8: mdio@8 {
+ reg = <8>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ spi2 {
+ compatible = "spi-gpio";
+ pinctrl-0 = <&pinctrl_dspi2>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio-sck = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+ gpio-mosi = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+ gpio-miso = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&gpio2 0 GPIO_ACTIVE_HIGH>;
+ num-chipselects = <1>;
+
+ at93c46d@0 {
+ compatible = "atmel,at93c46d";
+ #address-cells = <0>;
+ #size-cells = <0>;
+ reg = <0>;
+ spi-max-frequency = <500000>;
+ spi-cs-high;
+ data-size = <16>;
+ select-gpios = <&gpio2 4 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&dspi0 {
+ pinctrl-0 = <&pinctrl_dspi0>, <&pinctrl_dspi0_cs_4_5>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&dspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_dspi1>;
+ status = "okay";
+
+ m25p128@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p128", "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+
+ partition@0 {
+ label = "m25p128-0";
+ reg = <0x0 0x01000000>;
+ };
+ };
+
+ m25p128@1 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p128", "jedec,spi-nor";
+ reg = <1>;
+ spi-max-frequency = <50000000>;
+
+ partition@0 {
+ label = "m25p128-1";
+ reg = <0x0 0x01000000>;
+ };
+ };
+};
+
+&esdhc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_esdhc0>;
+ bus-width = <8>;
+ status = "okay";
+};
+
+&fec0 {
+ status = "disabled";
+};
+
+&i2c0 {
+ /* Reset Signals */
+ gpio5: pca9505@20 {
+ compatible = "nxp,pca9554";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ /* Board Revision */
+ gpio6: pca9505@22 {
+ compatible = "nxp,pca9554";
+ reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
+
+&i2c1 {
+ /* Wireless 2 */
+ gpio8: pca9554@18 {
+ compatible = "nxp,pca9557";
+ reg = <0x18>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ /* Wireless 1 */
+ gpio7: pca9554@24 {
+ compatible = "nxp,pca9554";
+ reg = <0x24>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ /* AIB voltage monitor */
+ adt7411@4a {
+ compatible = "adi,adt7411";
+ reg = <0x4a>;
+ };
+};
+
+&i2c2 {
+ /* FIB voltage monitor */
+ adt7411@4a {
+ compatible = "adi,adt7411";
+ reg = <0x4a>;
+ };
+
+ lm75_swb {
+ compatible = "national,lm75";
+ reg = <0x4e>;
+ };
+
+ lm75_swa {
+ compatible = "national,lm75";
+ reg = <0x4f>;
+ };
+
+ /* FIB Nameplate */
+ at24c08@57 {
+ compatible = "atmel,24c08";
+ reg = <0x57>;
+ };
+
+ tca9548@70 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x70>;
+
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ sff0: at24c04@50 {
+ compatible = "atmel,24c04";
+ reg = <0x50>;
+ };
+ };
+
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+
+ sff1: at24c04@50 {
+ compatible = "atmel,24c04";
+ reg = <0x50>;
+ };
+ };
+
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+
+ sff2: at24c04@50 {
+ compatible = "atmel,24c04";
+ reg = <0x50>;
+ };
+ };
+
+ i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+
+ sff3: at24c04@50 {
+ compatible = "atmel,24c04";
+ reg = <0x50>;
+ };
+ };
+
+ i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+
+ sff4: at24c04@50 {
+ compatible = "atmel,24c04";
+ reg = <0x50>;
+ };
+ };
+ };
+
+
+ tca9548@71 {
+ compatible = "nxp,pca9548";
+ reg = <0x71>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ sff5: at24c04@50 {
+ compatible = "atmel,24c04";
+ reg = <0x50>;
+ };
+ };
+
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+
+ sff6: at24c04@50 {
+ compatible = "atmel,24c04";
+ reg = <0x50>;
+ };
+ };
+
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+
+ sff7: at24c04@50 {
+ compatible = "atmel,24c04";
+ reg = <0x50>;
+ };
+
+ };
+
+ i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+
+ sff8: at24c04@50 {
+ compatible = "atmel,24c04";
+ reg = <0x50>;
+ };
+ };
+
+ i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+
+ sff9: at24c04@50 {
+ compatible = "atmel,24c04";
+ reg = <0x50>;
+ };
+ };
+ };
+};
+
+&uart1 {
+ linux,rs485-enabled-at-boot-time;
+ pinctrl-0 = <&pinctrl_uart1>, <&pinctrl_uart1_rts>;
+};
+
+&uart2 {
+ linux,rs485-enabled-at-boot-time;
+ pinctrl-0 = <&pinctrl_uart2>, <&pinctrl_uart2_rts>;
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpo_public>;
+
+
+ pinctrl_gpo_public: gpopubgrp {
+ fsl,pins = <
+ VF610_PAD_PTE2__GPIO_107 0x2062
+ VF610_PAD_PTE3__GPIO_108 0x2062
+ VF610_PAD_PTE4__GPIO_109 0x2062
+ VF610_PAD_PTE5__GPIO_110 0x2062
+ VF610_PAD_PTE6__GPIO_111 0x2062
+ >;
+ };
+
+ pinctrl_dspi0_cs_4_5: dspi0grp-cs-4-5 {
+ fsl,pins = <
+ VF610_PAD_PTB13__DSPI0_CS4 0x1182
+ VF610_PAD_PTB12__DSPI0_CS5 0x1182
+ >;
+ };
+
+ pinctrl_dspi1: dspi1grp {
+ fsl,pins = <
+ VF610_PAD_PTD5__DSPI1_CS0 0x1182
+ VF610_PAD_PTD4__DSPI1_CS1 0x1182
+ VF610_PAD_PTC6__DSPI1_SIN 0x1181
+ VF610_PAD_PTC7__DSPI1_SOUT 0x1182
+ VF610_PAD_PTC8__DSPI1_SCK 0x1182
+ >;
+ };
+
+ pinctrl_esdhc0: esdhc0grp {
+ fsl,pins = <
+ VF610_PAD_PTC0__ESDHC0_CLK 0x31ef
+ VF610_PAD_PTC1__ESDHC0_CMD 0x31ef
+ VF610_PAD_PTC2__ESDHC0_DAT0 0x31ef
+ VF610_PAD_PTC3__ESDHC0_DAT1 0x31ef
+ VF610_PAD_PTC4__ESDHC0_DAT2 0x31ef
+ VF610_PAD_PTC5__ESDHC0_DAT3 0x31ef
+ VF610_PAD_PTD23__ESDHC0_DAT4 0x31ef
+ VF610_PAD_PTD22__ESDHC0_DAT5 0x31ef
+ VF610_PAD_PTD21__ESDHC0_DAT6 0x31ef
+ VF610_PAD_PTD20__ESDHC0_DAT7 0x31ef
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ VF610_PAD_PTA30__I2C3_SCL 0x37ff
+ VF610_PAD_PTA31__I2C3_SDA 0x37ff
+ >;
+ };
+
+ pinctrl_leds_debug: pinctrl-leds-debug {
+ fsl,pins = <
+ VF610_PAD_PTB26__GPIO_96 0x31c2
+ >;
+ };
+
+ pinctrl_uart1_rts: uart1grp-rts {
+ fsl,pins = <
+ VF610_PAD_PTB25__UART1_RTS 0x2062
+ >;
+ };
+
+ pinctrl_uart2_rts: uart2grp-rts {
+ fsl,pins = <
+ VF610_PAD_PTD2__UART2_RTS 0x2062
+ >;
+ };
+
+ pinctrl_mdio_mux: pinctrl-mdio-mux {
+ fsl,pins = <
+ VF610_PAD_PTE27__GPIO_132 0x31c2
+ VF610_PAD_PTE28__GPIO_133 0x31c2
+ VF610_PAD_PTE21__GPIO_126 0x31c2
+ VF610_PAD_PTE22__GPIO_127 0x31c2
+ >;
+ };
+};
diff --git a/arch/arm/dts/vf610-zii-spu3-rev-a.dts b/arch/arm/dts/vf610-zii-spu3-rev-a.dts
new file mode 100644
index 0000000..25ab26d
--- /dev/null
+++ b/arch/arm/dts/vf610-zii-spu3-rev-a.dts
@@ -0,0 +1,140 @@
+/*
+ * Copyright (C) 2015, 2016 Zodiac Inflight Innovations
+ *
+ * Based on an original 'vf610-twr.dts' which is Copyright 2015,
+ * Freescale Semiconductor, Inc.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "vf610-zii-dev.dtsi"
+
+
+/ {
+ model = "ZII VF610 SPU3 Switch Management Board";
+ compatible = "zii,vf610spu3-a", "zii,vf610dev", "fsl,vf610";
+
+ aliases {
+ /delete-property/ serial2;
+ };
+
+ gpio-leds {
+ debug {
+ gpios = <&gpio2 18 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&dspi1 {
+ bus-num = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_dspi1>;
+ status = "okay";
+
+ m25p128@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p128", "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+
+ partition@0 {
+ label = "m25p128-0";
+ reg = <0x0 0x01000000>;
+ };
+ };
+};
+
+&esdhc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_esdhc0>;
+ bus-width = <8>;
+ status = "okay";
+};
+
+&fec0 {
+ status = "disabled";
+};
+
+&i2c0 {
+ /* Board Revision */
+ gpio6: pca9505@22 {
+ compatible = "nxp,pca9554";
+ reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
+
+/delete-node/ &i2c1;
+/delete-node/ &i2c2;
+/delete-node/ &uart2;
+
+&iomuxc {
+ pinctrl_dspi1: dspi1grp {
+ fsl,pins = <
+ VF610_PAD_PTD5__DSPI1_CS0 0x1182
+ VF610_PAD_PTD4__DSPI1_CS1 0x1182
+ VF610_PAD_PTC6__DSPI1_SIN 0x1181
+ VF610_PAD_PTC7__DSPI1_SOUT 0x1182
+ VF610_PAD_PTC8__DSPI1_SCK 0x1182
+ >;
+ };
+
+ pinctrl_esdhc0: esdhc0grp {
+ fsl,pins = <
+ VF610_PAD_PTC0__ESDHC0_CLK 0x31ef
+ VF610_PAD_PTC1__ESDHC0_CMD 0x31ef
+ VF610_PAD_PTC2__ESDHC0_DAT0 0x31ef
+ VF610_PAD_PTC3__ESDHC0_DAT1 0x31ef
+ VF610_PAD_PTC4__ESDHC0_DAT2 0x31ef
+ VF610_PAD_PTC5__ESDHC0_DAT3 0x31ef
+ VF610_PAD_PTD23__ESDHC0_DAT4 0x31ef
+ VF610_PAD_PTD22__ESDHC0_DAT5 0x31ef
+ VF610_PAD_PTD21__ESDHC0_DAT6 0x31ef
+ VF610_PAD_PTD20__ESDHC0_DAT7 0x31ef
+ >;
+ };
+
+ pinctrl_leds_debug: pinctrl-leds-debug {
+ fsl,pins = <
+ VF610_PAD_PTD3__GPIO_82 0x31c2
+ >;
+ };
+};
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index 62e6494..dba1041 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -355,6 +355,11 @@ config MACH_ZII_RDU2
bool "ZII i.MX6Q(+) RDU2"
select ARCH_IMX6
+config MACH_ZII_VF610_DEV
+ bool "Zodiac VF610 Dev Family"
+ select ARCH_VF610
+ select CLKDEV_LOOKUP
+
endif
# ----------------------------------------------------------
diff --git a/images/Makefile.imx b/images/Makefile.imx
index eba6048..b0c4694 100644
--- a/images/Makefile.imx
+++ b/images/Makefile.imx
@@ -423,3 +423,8 @@ pblx-$(CONFIG_MACH_ZII_RDU2) += start_imx6qp_zii_rdu2
CFG_start_imx6qp_zii_rdu2.pblx.imximg = $(board)/zii-imx6q-rdu2/flash-header-imx6qp-rdu2.imxcfg
FILE_barebox-zii-imx6qp-rdu2.img = start_imx6qp_zii_rdu2.pblx.imximg
image-$(CONFIG_MACH_ZII_RDU2) += barebox-zii-imx6qp-rdu2.img
+
+pblx-$(CONFIG_MACH_ZII_VF610_DEV) += start_zii_vf610_dev
+CFG_start_zii_vf610_dev.pblx.imximg = $(board)/zii-vf610-dev/flash-header-zii-vf610-dev.imxcfg
+FILE_barebox-zii-vf610-dev.img = start_zii_vf610_dev.pblx.imximg
+image-$(CONFIG_MACH_ZII_VF610_DEV) += barebox-zii-vf610-dev.img
--
2.9.3
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
next reply other threads:[~2017-02-03 15:55 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-02-03 15:53 Andrey Smirnov [this message]
2017-02-07 8:46 ` Sascha Hauer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170203155323.29430-1-andrew.smirnov@gmail.com \
--to=andrew.smirnov@gmail.com \
--cc=barebox@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox