* [PATCH v1 0/3] provide basic support for TP-Link WDR4300
@ 2017-08-09 15:51 Oleksij Rempel
2017-08-09 15:51 ` [PATCH v1 1/3] MIPS: ath79: provide CONFIG_SOC_QCA_AR9331 option Oleksij Rempel
` (2 more replies)
0 siblings, 3 replies; 6+ messages in thread
From: Oleksij Rempel @ 2017-08-09 15:51 UTC (permalink / raw)
To: barebox; +Cc: Oleksij Rempel
this set also including support of QCA AR9344 too.
Oleksij Rempel (3):
MIPS: ath79: provide CONFIG_SOC_QCA_AR9331 option
MIPS: ath79: add initial QCA AR9344 SoC support
MIPS: ath79: add TP-Link WDR4300 board support
arch/mips/Makefile | 1 +
arch/mips/boards/tplink-wdr4300/Makefile | 1 +
arch/mips/boards/tplink-wdr4300/board.c | 28 ++
.../tplink-wdr4300/include/board/board_pbl_start.h | 62 +++
arch/mips/configs/tplink-wdr4300_defconfig | 78 +++
arch/mips/dts/ar9344.dtsi | 53 ++
arch/mips/dts/ar9344_tl_wdr4300.dts | 63 +++
arch/mips/mach-ath79/Kconfig | 15 +
arch/mips/mach-ath79/include/mach/ar71xx_regs.h | 9 +
arch/mips/mach-ath79/include/mach/debug_ll.h | 167 +------
.../mips/mach-ath79/include/mach/debug_ll_ar9331.h | 176 +++++++
.../mips/mach-ath79/include/mach/debug_ll_ar9344.h | 191 ++++++++
.../include/mach/pbl_ll_init_ar9344_1.1.h | 540 +++++++++++++++++++++
13 files changed, 1226 insertions(+), 158 deletions(-)
create mode 100644 arch/mips/boards/tplink-wdr4300/Makefile
create mode 100644 arch/mips/boards/tplink-wdr4300/board.c
create mode 100644 arch/mips/boards/tplink-wdr4300/include/board/board_pbl_start.h
create mode 100644 arch/mips/configs/tplink-wdr4300_defconfig
create mode 100644 arch/mips/dts/ar9344.dtsi
create mode 100644 arch/mips/dts/ar9344_tl_wdr4300.dts
create mode 100644 arch/mips/mach-ath79/include/mach/debug_ll_ar9331.h
create mode 100644 arch/mips/mach-ath79/include/mach/debug_ll_ar9344.h
create mode 100644 arch/mips/mach-ath79/include/mach/pbl_ll_init_ar9344_1.1.h
--
2.11.0
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v1 1/3] MIPS: ath79: provide CONFIG_SOC_QCA_AR9331 option
2017-08-09 15:51 [PATCH v1 0/3] provide basic support for TP-Link WDR4300 Oleksij Rempel
@ 2017-08-09 15:51 ` Oleksij Rempel
2017-08-09 15:51 ` [PATCH v1 2/3] MIPS: ath79: add initial QCA AR9344 SoC support Oleksij Rempel
2017-08-09 15:51 ` [PATCH v1 3/3] MIPS: ath79: add TP-Link WDR4300 board support Oleksij Rempel
2 siblings, 0 replies; 6+ messages in thread
From: Oleksij Rempel @ 2017-08-09 15:51 UTC (permalink / raw)
To: barebox; +Cc: Oleksij Rempel
QCA AR9331 and QCA AR9344 have some similar part but different uart engines.
We need this flag to provide common debug_ll support.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
---
arch/mips/mach-ath79/Kconfig | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/arch/mips/mach-ath79/Kconfig b/arch/mips/mach-ath79/Kconfig
index 9b8e3946e..f2eae2532 100644
--- a/arch/mips/mach-ath79/Kconfig
+++ b/arch/mips/mach-ath79/Kconfig
@@ -4,17 +4,22 @@ config ARCH_TEXT_BASE
hex
default 0xa0800000
+config SOC_QCA_AR9331
+ bool
+
choice
prompt "Board type"
config BOARD_TPLINK_MR3020
bool "TP-LINK MR3020"
+ select SOC_QCA_AR9331
select HAVE_PBL_IMAGE
select HAVE_IMAGE_COMPRESSION
select HAS_NMON
config BOARD_BLACK_SWIFT
bool "Black Swift"
+ select SOC_QCA_AR9331
select HAVE_PBL_IMAGE
select HAVE_IMAGE_COMPRESSION
select HAS_NMON
--
2.11.0
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v1 2/3] MIPS: ath79: add initial QCA AR9344 SoC support
2017-08-09 15:51 [PATCH v1 0/3] provide basic support for TP-Link WDR4300 Oleksij Rempel
2017-08-09 15:51 ` [PATCH v1 1/3] MIPS: ath79: provide CONFIG_SOC_QCA_AR9331 option Oleksij Rempel
@ 2017-08-09 15:51 ` Oleksij Rempel
2017-08-09 15:51 ` [PATCH v1 3/3] MIPS: ath79: add TP-Link WDR4300 board support Oleksij Rempel
2 siblings, 0 replies; 6+ messages in thread
From: Oleksij Rempel @ 2017-08-09 15:51 UTC (permalink / raw)
To: barebox; +Cc: Oleksij Rempel
According to the documentation:
"The AR9344 is a highly integrated and feature-rich IEEE 802.11n 2x2 2.4/5 GHz
System-on-a-Chip (SoC) for advanced WLAN platforms.
It includes a MIPS 74Kc processor, PCI Express 1.1 Root Complex and Endpoint
interfaces, five port IEEE 802.3 Fast Ethernet Switch with MAC/PHY,
one MII/RMII/RGMII interface, one USB 2.0 MAC/PHY, and external memory
interface for serial Flash, SDRAM, DDR1 or DDR2, I2S/SPDIF-Out audio interface,
SLIC VOIP/PCM interface, two UARTs, and GPIOs that can be used for LED
controls or other general purpose interface configurations.
The AR9344 supports 802.11n operations up to 144 Mbps for 20 MHz and 300 Mbps
for 40 MHz respectively, and 802.11a/b/g data rates.
Additional features include Maximal Likelihood (ML) decoding, Low-Density
Parity Check (LDPC), Maximal Ratio Combining (MRC), Tx Beamforming (TxBF), and
On-Chip One-Time Programmable (OTP) memory."
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
---
arch/mips/dts/ar9344.dtsi | 53 ++
arch/mips/mach-ath79/include/mach/ar71xx_regs.h | 9 +
arch/mips/mach-ath79/include/mach/debug_ll.h | 167 +------
.../mips/mach-ath79/include/mach/debug_ll_ar9331.h | 176 +++++++
.../mips/mach-ath79/include/mach/debug_ll_ar9344.h | 191 ++++++++
.../include/mach/pbl_ll_init_ar9344_1.1.h | 540 +++++++++++++++++++++
6 files changed, 978 insertions(+), 158 deletions(-)
create mode 100644 arch/mips/dts/ar9344.dtsi
create mode 100644 arch/mips/mach-ath79/include/mach/debug_ll_ar9331.h
create mode 100644 arch/mips/mach-ath79/include/mach/debug_ll_ar9344.h
create mode 100644 arch/mips/mach-ath79/include/mach/pbl_ll_init_ar9344_1.1.h
diff --git a/arch/mips/dts/ar9344.dtsi b/arch/mips/dts/ar9344.dtsi
new file mode 100644
index 000000000..0838e8d7f
--- /dev/null
+++ b/arch/mips/dts/ar9344.dtsi
@@ -0,0 +1,53 @@
+#include <dt-bindings/clock/ath79-clk.h>
+
+/ {
+ compatible = "qca,ar9344";
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "mips,mips74Kc";
+ reg = <0>;
+ };
+ };
+
+ ref: ref {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ };
+
+ ahb {
+ compatible = "simple-bus";
+ ranges;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ uart0: uart@18020000 {
+ compatible = "ns16550a", "qca,ar9344-uart0";
+ reg = <0x18020000 0x20>;
+
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ big-endian;
+
+ status = "disabled";
+ };
+
+ spi: spi@1f000000 {
+ compatible = "qca,ar7100-spi", "qca,ar9344-spi";
+ reg = <0x1f000000 0x1c>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+ };
+ };
+};
diff --git a/arch/mips/mach-ath79/include/mach/ar71xx_regs.h b/arch/mips/mach-ath79/include/mach/ar71xx_regs.h
index de96c565a..f56c3f724 100644
--- a/arch/mips/mach-ath79/include/mach/ar71xx_regs.h
+++ b/arch/mips/mach-ath79/include/mach/ar71xx_regs.h
@@ -37,6 +37,15 @@
#define AR933X_UART_BASE (AR71XX_APB_BASE + 0x00020000)
#define AR933X_UART_SIZE 0x14
+#define AR934X_UART0_BASE (AR71XX_APB_BASE + 0x00020000)
+#define AR934X_UART0_SIZE 0x18
+#define AR934X_UART0_SHIFT 2
+
+/* WASP BootStrap Register */
+#define WASP_BOOTSTRAP_REG (AR71XX_RESET_BASE + 0xb0)
+#define WASP_REF_CLK_25 (1 << 4) /* 0 - 25MHz 1 - 40 MHz */
+#define WASP_RAM_TYPE(a) ((a) & 0x3)
+
/*
* RTC block
*/
diff --git a/arch/mips/mach-ath79/include/mach/debug_ll.h b/arch/mips/mach-ath79/include/mach/debug_ll.h
index 04bd3ea72..73d064a3a 100644
--- a/arch/mips/mach-ath79/include/mach/debug_ll.h
+++ b/arch/mips/mach-ath79/include/mach/debug_ll.h
@@ -1,5 +1,5 @@
/*
- * based on linux.git/drivers/tty/serial/ar933x_uart.c
+ * Copyright (C) 2013 Antony Pavlov <antonynpavlov@gmail.com>
*
* This file is part of barebox.
* See file CREDITS for list of people who contributed to this project.
@@ -15,162 +15,13 @@
*
*/
-#ifndef __AR933X_DEBUG_LL__
-#define __AR933X_DEBUG_LL__
+#ifndef __MACH_ATH79_DEBUG_LL__
+#define __MACH_ATH79_DEBUG_LL__
-#include <asm/addrspace.h>
-#include <mach/ar71xx_regs.h>
+#if defined(CONFIG_SOC_QCA_AR9331)
+#include <mach/debug_ll_ar9331.h>
+#elif defined(CONFIG_SOC_QCA_AR9344)
+#include <mach/debug_ll_ar9344.h>
+#endif
-#define DEBUG_LL_UART_ADDR KSEG1ADDR(AR933X_UART_BASE)
-
-#define AR933X_UART_DATA_REG 0x00
-#define AR933X_UART_DATA_TX_RX_MASK 0xff
-#define AR933X_UART_DATA_TX_CSR 0x200
-#define AR933X_UART_DATA_RX_CSR 0x100
-
-#ifndef __ASSEMBLY__
-
-#include <io.h>
-
-/*
- * C macros
- */
-
-static inline void ar933x_debug_ll_writel(u32 b, int offset)
-{
- __raw_writel(b, (u8 *)DEBUG_LL_UART_ADDR + offset);
-}
-
-static inline u32 ar933x_debug_ll_readl(int offset)
-{
- return __raw_readl((u8 *)DEBUG_LL_UART_ADDR + offset);
-}
-
-static inline void PUTC_LL(int ch)
-{
- u32 data;
-
- /* wait transmitter ready */
- data = ar933x_debug_ll_readl(AR933X_UART_DATA_REG);
- while (!(data & AR933X_UART_DATA_TX_CSR))
- data = ar933x_debug_ll_readl(AR933X_UART_DATA_REG);
-
- data = (ch & AR933X_UART_DATA_TX_RX_MASK) | AR933X_UART_DATA_TX_CSR;
- ar933x_debug_ll_writel(data, AR933X_UART_DATA_REG);
-}
-#else /* __ASSEMBLY__ */
-/*
- * Macros for use in assembly language code
- */
-
-#define AR933X_UART_CS_REG 0x04
-#define UART_CS_REG ((KSEG1 | AR933X_UART_BASE) | AR933X_UART_CS_REG)
-#define AR933X_UART_CS_IF_MODE_S 2
-#define AR933X_UART_CS_IF_MODE_DCE 2
-#define AR933X_UART_CS_TX_READY_ORIDE BIT(7)
-#define AR933X_UART_CS_RX_READY_ORIDE BIT(8)
-
-/*
- * simple uart clock setup
- * from u-boot_mod/u-boot/cpu/mips/ar7240/hornet_serial.c
- */
-#define BAUD_CLOCK 25000000
-#define CLOCK_SCALE ((BAUD_CLOCK / (16 * CONFIG_BAUDRATE)) - 1)
-#define CLOCK_STEP 0x2000
-
-#define AR933X_UART_CLOCK_REG 0x08
-#define CLOCK_REG ((KSEG1 | AR933X_UART_BASE) | AR933X_UART_CLOCK_REG)
-
-.macro debug_ll_ar9331_init
-#ifdef CONFIG_DEBUG_LL
-
- pbl_reg_writel ((AR933X_UART_CS_IF_MODE_DCE << AR933X_UART_CS_IF_MODE_S) \
- | AR933X_UART_CS_TX_READY_ORIDE \
- | AR933X_UART_CS_RX_READY_ORIDE), UART_CS_REG
- pbl_reg_writel ((CLOCK_SCALE << 16) | CLOCK_STEP), CLOCK_REG
-
-#endif /* CONFIG_DEBUG_LL */
-.endm
-
-/*
- * output a character in a0
- */
-.macro debug_ll_outc_a0
-#ifdef CONFIG_DEBUG_LL
- .set push
- .set reorder
-
- la t0, DEBUG_LL_UART_ADDR
-201:
- lw t1, AR933X_UART_DATA_REG(t0) /* get line status */
- andi t1, t1, AR933X_UART_DATA_TX_CSR /* check for transmitter empty */
- beqz t1, 201b /* try again */
- andi a0, a0, AR933X_UART_DATA_TX_RX_MASK
- ori a0, a0, AR933X_UART_DATA_TX_CSR
- sw a0, 0(t0) /* write the character */
- .set pop
-#endif /* CONFIG_DEBUG_LL */
-.endm
-
-/*
- * output a character
- */
-.macro debug_ll_outc chr
-#ifdef CONFIG_DEBUG_LL
- li a0, \chr
- debug_ll_outc_a0
-#endif /* CONFIG_DEBUG_LL */
-.endm
-
-/*
- * check character in input buffer
- * return value:
- * v0 = 0 no character in input buffer
- * v0 != 0 character in input buffer
- */
-/* FIXME: use tstc */
-.macro debug_ll_tstc
-#ifdef CONFIG_DEBUG_LL
- .set push
- .set reorder
-
- la t0, DEBUG_LL_UART_ADDR
-
- /* get line status and check for data present */
- lw v0, AR933X_UART_DATA_REG(t0)
- andi v0, v0, AR933X_UART_DATA_RX_CSR
-
- .set pop
-#endif /* CONFIG_DEBUG_LL */
-.endm
-
-/*
- * get character to v0
- */
-.macro debug_ll_getc
-#ifdef CONFIG_DEBUG_LL
- .set push
- .set reorder
-
- la t0, DEBUG_LL_UART_ADDR
-204:
- lw v0, AR933X_UART_DATA_REG(t0)
- andi v0, v0, AR933X_UART_DATA_RX_CSR
-
- /* try again */
- beqz v0, 204b
-
- /* read a character */
- lw v0, AR933X_UART_DATA_REG(t0)
- andi v0, v0, AR933X_UART_DATA_TX_RX_MASK
-
- /* remove the character from the FIFO */
- li t1, AR933X_UART_DATA_RX_CSR
- sw t1, AR933X_UART_DATA_REG(t0)
-
- .set pop
-#endif /* CONFIG_DEBUG_LL */
-.endm
-#endif /* __ASSEMBLY__ */
-
-#endif /* __AR933X_DEBUG_LL__ */
+#endif /* __MACH_AR9344_DEBUG_LL_H__ */
diff --git a/arch/mips/mach-ath79/include/mach/debug_ll_ar9331.h b/arch/mips/mach-ath79/include/mach/debug_ll_ar9331.h
new file mode 100644
index 000000000..04bd3ea72
--- /dev/null
+++ b/arch/mips/mach-ath79/include/mach/debug_ll_ar9331.h
@@ -0,0 +1,176 @@
+/*
+ * based on linux.git/drivers/tty/serial/ar933x_uart.c
+ *
+ * This file is part of barebox.
+ * See file CREDITS for list of people who contributed to this project.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef __AR933X_DEBUG_LL__
+#define __AR933X_DEBUG_LL__
+
+#include <asm/addrspace.h>
+#include <mach/ar71xx_regs.h>
+
+#define DEBUG_LL_UART_ADDR KSEG1ADDR(AR933X_UART_BASE)
+
+#define AR933X_UART_DATA_REG 0x00
+#define AR933X_UART_DATA_TX_RX_MASK 0xff
+#define AR933X_UART_DATA_TX_CSR 0x200
+#define AR933X_UART_DATA_RX_CSR 0x100
+
+#ifndef __ASSEMBLY__
+
+#include <io.h>
+
+/*
+ * C macros
+ */
+
+static inline void ar933x_debug_ll_writel(u32 b, int offset)
+{
+ __raw_writel(b, (u8 *)DEBUG_LL_UART_ADDR + offset);
+}
+
+static inline u32 ar933x_debug_ll_readl(int offset)
+{
+ return __raw_readl((u8 *)DEBUG_LL_UART_ADDR + offset);
+}
+
+static inline void PUTC_LL(int ch)
+{
+ u32 data;
+
+ /* wait transmitter ready */
+ data = ar933x_debug_ll_readl(AR933X_UART_DATA_REG);
+ while (!(data & AR933X_UART_DATA_TX_CSR))
+ data = ar933x_debug_ll_readl(AR933X_UART_DATA_REG);
+
+ data = (ch & AR933X_UART_DATA_TX_RX_MASK) | AR933X_UART_DATA_TX_CSR;
+ ar933x_debug_ll_writel(data, AR933X_UART_DATA_REG);
+}
+#else /* __ASSEMBLY__ */
+/*
+ * Macros for use in assembly language code
+ */
+
+#define AR933X_UART_CS_REG 0x04
+#define UART_CS_REG ((KSEG1 | AR933X_UART_BASE) | AR933X_UART_CS_REG)
+#define AR933X_UART_CS_IF_MODE_S 2
+#define AR933X_UART_CS_IF_MODE_DCE 2
+#define AR933X_UART_CS_TX_READY_ORIDE BIT(7)
+#define AR933X_UART_CS_RX_READY_ORIDE BIT(8)
+
+/*
+ * simple uart clock setup
+ * from u-boot_mod/u-boot/cpu/mips/ar7240/hornet_serial.c
+ */
+#define BAUD_CLOCK 25000000
+#define CLOCK_SCALE ((BAUD_CLOCK / (16 * CONFIG_BAUDRATE)) - 1)
+#define CLOCK_STEP 0x2000
+
+#define AR933X_UART_CLOCK_REG 0x08
+#define CLOCK_REG ((KSEG1 | AR933X_UART_BASE) | AR933X_UART_CLOCK_REG)
+
+.macro debug_ll_ar9331_init
+#ifdef CONFIG_DEBUG_LL
+
+ pbl_reg_writel ((AR933X_UART_CS_IF_MODE_DCE << AR933X_UART_CS_IF_MODE_S) \
+ | AR933X_UART_CS_TX_READY_ORIDE \
+ | AR933X_UART_CS_RX_READY_ORIDE), UART_CS_REG
+ pbl_reg_writel ((CLOCK_SCALE << 16) | CLOCK_STEP), CLOCK_REG
+
+#endif /* CONFIG_DEBUG_LL */
+.endm
+
+/*
+ * output a character in a0
+ */
+.macro debug_ll_outc_a0
+#ifdef CONFIG_DEBUG_LL
+ .set push
+ .set reorder
+
+ la t0, DEBUG_LL_UART_ADDR
+201:
+ lw t1, AR933X_UART_DATA_REG(t0) /* get line status */
+ andi t1, t1, AR933X_UART_DATA_TX_CSR /* check for transmitter empty */
+ beqz t1, 201b /* try again */
+ andi a0, a0, AR933X_UART_DATA_TX_RX_MASK
+ ori a0, a0, AR933X_UART_DATA_TX_CSR
+ sw a0, 0(t0) /* write the character */
+ .set pop
+#endif /* CONFIG_DEBUG_LL */
+.endm
+
+/*
+ * output a character
+ */
+.macro debug_ll_outc chr
+#ifdef CONFIG_DEBUG_LL
+ li a0, \chr
+ debug_ll_outc_a0
+#endif /* CONFIG_DEBUG_LL */
+.endm
+
+/*
+ * check character in input buffer
+ * return value:
+ * v0 = 0 no character in input buffer
+ * v0 != 0 character in input buffer
+ */
+/* FIXME: use tstc */
+.macro debug_ll_tstc
+#ifdef CONFIG_DEBUG_LL
+ .set push
+ .set reorder
+
+ la t0, DEBUG_LL_UART_ADDR
+
+ /* get line status and check for data present */
+ lw v0, AR933X_UART_DATA_REG(t0)
+ andi v0, v0, AR933X_UART_DATA_RX_CSR
+
+ .set pop
+#endif /* CONFIG_DEBUG_LL */
+.endm
+
+/*
+ * get character to v0
+ */
+.macro debug_ll_getc
+#ifdef CONFIG_DEBUG_LL
+ .set push
+ .set reorder
+
+ la t0, DEBUG_LL_UART_ADDR
+204:
+ lw v0, AR933X_UART_DATA_REG(t0)
+ andi v0, v0, AR933X_UART_DATA_RX_CSR
+
+ /* try again */
+ beqz v0, 204b
+
+ /* read a character */
+ lw v0, AR933X_UART_DATA_REG(t0)
+ andi v0, v0, AR933X_UART_DATA_TX_RX_MASK
+
+ /* remove the character from the FIFO */
+ li t1, AR933X_UART_DATA_RX_CSR
+ sw t1, AR933X_UART_DATA_REG(t0)
+
+ .set pop
+#endif /* CONFIG_DEBUG_LL */
+.endm
+#endif /* __ASSEMBLY__ */
+
+#endif /* __AR933X_DEBUG_LL__ */
diff --git a/arch/mips/mach-ath79/include/mach/debug_ll_ar9344.h b/arch/mips/mach-ath79/include/mach/debug_ll_ar9344.h
new file mode 100644
index 000000000..d156ce9f3
--- /dev/null
+++ b/arch/mips/mach-ath79/include/mach/debug_ll_ar9344.h
@@ -0,0 +1,191 @@
+/*
+ * Copyright (C) 2017 Oleksij Rempel <o.rempel@pengutronix.de>
+ * Copyright (C) 2012, 2013 Antony Pavlov <antonynpavlov@gmail.com>
+ *
+ * This file is part of barebox.
+ * See file CREDITS for list of people who contributed to this project.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef __AR9344_DEBUG_LL__
+#define __AR9344_DEBUG_LL__
+
+#include <asm/addrspace.h>
+#include <mach/ar71xx_regs.h>
+
+#define DEBUG_LL_UART_ADDR KSEG1ADDR(AR934X_UART0_BASE)
+#define DEBUG_LL_UART_SHIFT AR934X_UART0_SHIFT
+
+#define DEBUG_LL_UART_DIVISOR_40 (40000000 / (16 * CONFIG_BAUDRATE))
+#define DEBUG_LL_UART_DIVISOR_25 (25000000 / (16 * CONFIG_BAUDRATE))
+
+#define UART_THR (0x0 << DEBUG_LL_UART_SHIFT)
+#define UART_RBR (0x0 << DEBUG_LL_UART_SHIFT)
+#define UART_DLL (0x0 << DEBUG_LL_UART_SHIFT)
+#define UART_IER (0x1 << DEBUG_LL_UART_SHIFT)
+#define UART_DLM (0x1 << DEBUG_LL_UART_SHIFT)
+#define UART_FCR (0x2 << DEBUG_LL_UART_SHIFT)
+#define UART_LCR (0x3 << DEBUG_LL_UART_SHIFT)
+#define UART_LSR (0x5 << DEBUG_LL_UART_SHIFT)
+
+#define UART_LCR_W 0x07 /* Set UART to 8,N,2 & DLAB = 0 */
+#define UART_LCR_DLAB 0x87 /* Set UART to 8,N,2 & DLAB = 1 */
+
+#define UART_LSR_DR 0x01 /* UART received data present */
+#define UART_LSR_THRE 0x20 /* Xmit holding register empty */
+
+#define UART_FCR_RST 0x07 /* FIFO_EN | RCVR_FIFO_RST | XMIT_FIFO_RST */
+
+#ifndef __ASSEMBLY__
+
+/*
+ * C macros
+ */
+
+#include <asm/io.h>
+
+static inline void PUTC_LL(char ch)
+{
+#ifdef CONFIG_DEBUG_LL
+ while (!(__raw_readl((u8 *)DEBUG_LL_UART_ADDR + UART_LSR) & UART_LSR_THRE))
+ ;
+ __raw_writel(ch, (u8 *)DEBUG_LL_UART_ADDR + UART_THR);
+#endif /* CONFIG_DEBUG_LL */
+}
+#else /* __ASSEMBLY__ */
+/*
+ * Macros for use in assembly language code
+ */
+
+.macro debug_ll_ar9344_init
+#ifdef CONFIG_DEBUG_LL
+
+ /* find out the ref clock */
+ li t5, KSEG1ADDR(WASP_BOOTSTRAP_REG);
+ li t6, WASP_REF_CLK_25
+ lw t7, 0(t5);
+ and t6, t7, t6
+ beq zero, t6, uart_setup_ref25_val
+ nop
+uart_setup_ref40_val:
+ li t5, DEBUG_LL_UART_DIVISOR_40
+ b 1f
+ nop
+
+uart_setup_ref25_val:
+ li t5, DEBUG_LL_UART_DIVISOR_25
+1:
+
+ la t0, DEBUG_LL_UART_ADDR
+
+ li t1, UART_LCR_DLAB /* DLAB on */
+ sw t1, UART_LCR(t0) /* Write it out */
+
+ sw t5, UART_DLL(t0) /* write low order byte */
+ li t1, 0
+ sw t1, UART_DLM(t0) /* write high order byte */
+
+ li t1, UART_LCR_W /* DLAB off */
+ sw t1, UART_LCR(t0) /* Write it out */
+
+ li t1, UART_FCR_RST /* reset FIFOs */
+ sw t1, UART_FCR(t0) /* Write it out */
+
+ li t1, 0 /* disable interrupts */
+ sw t1, UART_IER(t0) /* Write it out */
+#endif /* CONFIG_DEBUG_LL */
+.endm
+
+/*
+ * output a character in a0
+ */
+.macro debug_ll_outc_a0
+#ifdef CONFIG_DEBUG_LL
+ .set push
+ .set reorder
+
+ la t0, DEBUG_LL_UART_ADDR
+
+201: lw t1, UART_LSR(t0) /* get line status */
+ andi t1, t1, UART_LSR_THRE /* check for transmitter empty */
+ beqz t1, 201b /* try again */
+
+ sw a0, UART_THR(t0) /* write the character */
+
+ .set pop
+#endif /* CONFIG_DEBUG_LL */
+.endm
+
+/*
+ * output a character
+ */
+.macro debug_ll_outc chr
+#ifdef CONFIG_DEBUG_LL
+ li a0, \chr
+ debug_ll_outc_a0
+#endif /* CONFIG_DEBUG_LL */
+.endm
+
+/*
+ * output CR + NL
+ */
+.macro debug_ll_outnl
+#ifdef CONFIG_DEBUG_LL
+ debug_ll_outc '\r'
+ debug_ll_outc '\n'
+#endif /* CONFIG_DEBUG_LL */
+.endm
+
+/*
+ * check character in input buffer
+ * return value:
+ * v0 = 0 no character in input buffer
+ * v0 != 0 character in input buffer
+ */
+.macro debug_ll_tstc
+#ifdef CONFIG_DEBUG_LL
+ .set push
+ .set reorder
+
+ la t0, DEBUG_LL_UART_ADDR
+
+ /* get line status and check for data present */
+ lw t1, UART_LSR(t0)
+ andi v0, t1, UART_LSR_DR
+
+ .set pop
+#endif /* CONFIG_DEBUG_LL */
+.endm
+
+/*
+ * get character to v0
+ */
+.macro debug_ll_getc
+#ifdef CONFIG_DEBUG_LL
+ .set push
+ .set reorder
+
+204:
+ debug_ll_tstc
+
+ /* try again */
+ beqz v0, 204b
+
+ /* read a character */
+ lw v0, UART_RBR(t0)
+
+ .set pop
+#endif /* CONFIG_DEBUG_LL */
+.endm
+#endif /* __ASSEMBLY__ */
+
+#endif /* __INCLUDE_MIPS_ASM_DEBUG_LL_NS16550_H__ */
diff --git a/arch/mips/mach-ath79/include/mach/pbl_ll_init_ar9344_1.1.h b/arch/mips/mach-ath79/include/mach/pbl_ll_init_ar9344_1.1.h
new file mode 100644
index 000000000..594ec1155
--- /dev/null
+++ b/arch/mips/mach-ath79/include/mach/pbl_ll_init_ar9344_1.1.h
@@ -0,0 +1,540 @@
+#ifndef __ASM_MACH_ATH79_PBL_LL_INIT_AR9344_1_1_H
+#define __ASM_MACH_ATH79_PBL_LL_INIT_AR9344_1_1_H
+
+#include <asm/addrspace.h>
+#include <asm/regdef.h>
+
+#define AR7240_APB_BASE (KSEG1 | 0x18000000) /* 384M */
+#define AR7240_DDR_CTL_BASE AR7240_APB_BASE+0x00000000
+#define AR7240_PLL_BASE AR7240_APB_BASE+0x00050000
+
+#define ATH_DDR_COUNT_LOC (KSEG1 | 0x1d000000)
+#define ATH_CPU_COUNT_LOC (KSEG1 | 0x1d000004)
+
+/*
+ * DDR block
+ */
+#define AR7240_DDR_CONFIG AR7240_DDR_CTL_BASE+0
+#define AR7240_DDR_CONFIG2 AR7240_DDR_CTL_BASE+4
+#define AR7240_DDR_MODE AR7240_DDR_CTL_BASE+0x08
+#define AR7240_DDR_EXT_MODE AR7240_DDR_CTL_BASE+0x0c
+#define AR7240_DDR_CONTROL AR7240_DDR_CTL_BASE+0x10
+#define AR7240_DDR_REFRESH AR7240_DDR_CTL_BASE+0x14
+#define AR7240_DDR_RD_DATA_THIS_CYCLE AR7240_DDR_CTL_BASE+0x18
+#define AR7240_DDR_TAP_CONTROL0 AR7240_DDR_CTL_BASE+0x1c
+#define AR7240_DDR_TAP_CONTROL1 AR7240_DDR_CTL_BASE+0x20
+#define AR7240_DDR_TAP_CONTROL2 AR7240_DDR_CTL_BASE+0x24
+#define AR7240_DDR_TAP_CONTROL3 AR7240_DDR_CTL_BASE+0x28
+#define AR7240_DDR_DDR2_CONFIG AR7240_DDR_CTL_BASE+0x8c
+#define AR7240_DDR_BURST AR7240_DDR_CTL_BASE+0xc4
+#define AR7240_DDR_BURST2 AR7240_DDR_CTL_BASE+0xc8
+#define AR7240_AHB_MASTER_TIMEOUT AR7240_DDR_CTL_BASE+0xcc
+#define AR7240_DDR_CTL_CONFIG AR7240_DDR_CTL_BASE+0x108
+#define AR7240_DDR_DEBUG_RD_CNTL AR7240_DDR_CTL_BASE+0x118
+
+#define AR934X_CPU_PLL_DITHER AR7240_PLL_BASE+0x0048
+
+#define AR934X_CPU_PLL_CONFIG AR7240_PLL_BASE+0x0000
+#define AR934X_DDR_PLL_CONFIG AR7240_PLL_BASE+0x0004
+#define AR934X_CPU_DDR_CLOCK_CONTROL AR7240_PLL_BASE+0x0008
+#define AR934X_DDR_PLL_DITHER AR7240_PLL_BASE+0x0044
+
+#define CPU_DPLL3_ADDRESS (KSEG1 | 0x181161c8)
+#define CPU_DPLL4_ADDRESS (KSEG1 | 0x181161cc)
+#define DDR_DPLL3_ADDRESS (KSEG1 | 0x18116248)
+#define DDR_DPLL4_ADDRESS (KSEG1 | 0x1811624c)
+
+#define DPLL2_ADDRESS_c4 (KSEG1 | 0x181161c4)
+#define DPLL2_ADDRESS_44 (KSEG1 | 0x18116244)
+#define DPLL3_ADDRESS_88 (KSEG1 | 0x18116188)
+
+#define CPU_PLL_CONFIG_NINT_VAL_40 0x380
+#define DDR_PLL_CONFIG_NINT_VAL_40 0x3000
+#define CPU_PLL_NFRAC_40 0
+#define DDR_PLL_NFRAC_40 0
+
+#define CPU_PLL_CONFIG_NINT_VAL_25 0x580
+#define DDR_PLL_CONFIG_NINT_VAL_25 0x4c00
+#define CPU_PLL_NFRAC_25 0x659
+#define DDR_PLL_NFRAC_25 0x330cc
+
+#define CPU_PLL_DITHER_DITHER_EN_LSB 31
+#define CPU_PLL_DITHER_DITHER_EN_MASK 0x80000000
+#define CPU_PLL_DITHER_DITHER_EN_SET(x) \
+ (((x) << CPU_PLL_DITHER_DITHER_EN_LSB) \
+ & CPU_PLL_DITHER_DITHER_EN_MASK)
+
+#define CPU_PLL_DITHER_NFRAC_STEP_LSB 12
+#define CPU_PLL_DITHER_NFRAC_STEP_MASK 0x0003f000
+#define CPU_PLL_DITHER_NFRAC_STEP_SET(x) \
+ (((x) << CPU_PLL_DITHER_NFRAC_STEP_LSB) \
+ & CPU_PLL_DITHER_NFRAC_STEP_MASK)
+
+#define CPU_PLL_DITHER_UPDATE_COUNT_LSB 18
+#define CPU_PLL_DITHER_UPDATE_COUNT_MASK 0x00fc0000
+#define CPU_PLL_DITHER_UPDATE_COUNT_SET(x) \
+ (((x) << CPU_PLL_DITHER_UPDATE_COUNT_LSB) \
+ & CPU_PLL_DITHER_UPDATE_COUNT_MASK)
+
+#define DDR_PLL_DITHER_DITHER_EN_LSB 31
+#define DDR_PLL_DITHER_DITHER_EN_MASK 0x80000000
+#define DDR_PLL_DITHER_DITHER_EN_SET(x) \
+ (((x) << DDR_PLL_DITHER_DITHER_EN_LSB) \
+ & DDR_PLL_DITHER_DITHER_EN_MASK)
+
+#define DDR_PLL_DITHER_NFRAC_STEP_LSB 20
+#define DDR_PLL_DITHER_NFRAC_STEP_MASK 0x07f00000
+#define DDR_PLL_DITHER_NFRAC_STEP_SET(x) \
+ (((x) << DDR_PLL_DITHER_NFRAC_STEP_LSB) \
+ & DDR_PLL_DITHER_NFRAC_STEP_MASK)
+
+#define DDR_PLL_DITHER_UPDATE_COUNT_LSB 27
+#define DDR_PLL_DITHER_UPDATE_COUNT_MASK 0x78000000
+#define DDR_PLL_DITHER_UPDATE_COUNT_SET(x) \
+ (((x) << DDR_PLL_DITHER_UPDATE_COUNT_LSB) \
+ & DDR_PLL_DITHER_UPDATE_COUNT_MASK)
+
+#define CPU_DDR_CLOCK_CONTROL_CPU_PLL_BYPASS_LSB 2
+#define CPU_DDR_CLOCK_CONTROL_CPU_PLL_BYPASS_MASK 0x00000004
+#define CPU_DDR_CLOCK_CONTROL_CPU_PLL_BYPASS_SET(x) \
+ (((x) << CPU_DDR_CLOCK_CONTROL_CPU_PLL_BYPASS_LSB) \
+ & CPU_DDR_CLOCK_CONTROL_CPU_PLL_BYPASS_MASK)
+
+#define CPU_DDR_CLOCK_CONTROL_DDR_PLL_BYPASS_LSB 3
+#define CPU_DDR_CLOCK_CONTROL_DDR_PLL_BYPASS_MASK 0x00000008
+#define CPU_DDR_CLOCK_CONTROL_DDR_PLL_BYPASS_SET(x) \
+ (((x) << CPU_DDR_CLOCK_CONTROL_DDR_PLL_BYPASS_LSB) \
+ & CPU_DDR_CLOCK_CONTROL_DDR_PLL_BYPASS_MASK)
+
+#define CPU_DDR_CLOCK_CONTROL_AHB_PLL_BYPASS_LSB 4
+#define CPU_DDR_CLOCK_CONTROL_AHB_PLL_BYPASS_MASK 0x00000010
+#define CPU_DDR_CLOCK_CONTROL_AHB_PLL_BYPASS_SET(x) \
+ (((x) << CPU_DDR_CLOCK_CONTROL_AHB_PLL_BYPASS_LSB) \
+ & CPU_DDR_CLOCK_CONTROL_AHB_PLL_BYPASS_MASK)
+
+#define CPU_DPLL3_DO_MEAS_LSB 30
+#define CPU_DPLL3_DO_MEAS_MASK 0x40000000
+#define CPU_DPLL3_DO_MEAS_SET(x) \
+ (((x) << CPU_DPLL3_DO_MEAS_LSB) & CPU_DPLL3_DO_MEAS_MASK)
+
+#define CPU_DPLL3_SQSUM_DVC_LSB 3
+#define CPU_DPLL3_SQSUM_DVC_MASK 0x007ffff8
+#define CPU_DPLL3_SQSUM_DVC_SET(x) \
+ (((x) << CPU_DPLL3_SQSUM_DVC_LSB) & CPU_DPLL3_SQSUM_DVC_MASK)
+
+#define CPU_DPLL4_MEAS_DONE_LSB 3
+#define CPU_DPLL4_MEAS_DONE_MASK 0x00000008
+#define CPU_DPLL4_MEAS_DONE_SET(x) \
+ (((x) << CPU_DPLL4_MEAS_DONE_LSB) & CPU_DPLL4_MEAS_DONE_MASK)
+
+#define CPU_PLL_CONFIG_PLLPWD_LSB 30
+#define CPU_PLL_CONFIG_PLLPWD_MASK 0x40000000
+#define CPU_PLL_CONFIG_PLLPWD_SET(x) \
+ (((x) << CPU_PLL_CONFIG_PLLPWD_LSB) & CPU_PLL_CONFIG_PLLPWD_MASK)
+
+#define DDR_DPLL3_DO_MEAS_LSB 30
+#define DDR_DPLL3_DO_MEAS_MASK 0x40000000
+#define DDR_DPLL3_DO_MEAS_SET(x) \
+ (((x) << DDR_DPLL3_DO_MEAS_LSB) & DDR_DPLL3_DO_MEAS_MASK)
+
+#define DDR_DPLL3_SQSUM_DVC_LSB 3
+#define DDR_DPLL3_SQSUM_DVC_MASK 0x007ffff8
+#define DDR_DPLL3_SQSUM_DVC_SET(x) \
+ (((x) << DDR_DPLL3_SQSUM_DVC_LSB) & DDR_DPLL3_SQSUM_DVC_MASK)
+
+#define DDR_DPLL4_MEAS_DONE_LSB 3
+#define DDR_DPLL4_MEAS_DONE_MASK 0x00000008
+#define DDR_DPLL4_MEAS_DONE_SET(x) \
+ (((x) << DDR_DPLL4_MEAS_DONE_LSB) & DDR_DPLL4_MEAS_DONE_MASK)
+
+#define DDR_PLL_CONFIG_PLLPWD_LSB 30
+#define DDR_PLL_CONFIG_PLLPWD_MASK 0x40000000
+#define DDR_PLL_CONFIG_PLLPWD_SET(x) \
+ (((x) << DDR_PLL_CONFIG_PLLPWD_LSB) & DDR_PLL_CONFIG_PLLPWD_MASK)
+
+/*
+ * Helper macros.
+ * These Clobber t7, t8 and t9
+ */
+#define set_val(_reg, _mask, _val) \
+ li t7, KSEG1ADDR(_reg); \
+ lw t8, 0(t7); \
+ li t9, ~_mask; \
+ and t8, t8, t9; \
+ li t9, _val; \
+ or t8, t8, t9; \
+ sw t8, 0(t7)
+
+#define cpu_ddr_control_set(_mask, _val) \
+ set_val(AR934X_CPU_DDR_CLOCK_CONTROL, _mask, _val)
+
+#define set_srif_pll_reg(reg, _r) \
+ li t7, KSEG1ADDR(reg); \
+ sw _r, 0(t7);
+
+#define inc_loop_count(loc) \
+ li t9, loc; \
+ lw t7, 0(t9); \
+ addi t7, t7, 1; \
+ sw t7, 0(t9);
+
+#define clear_loop_count(loc) \
+ li t9, loc; \
+ sw zero, 0(t9);
+
+/******************************************************************************
+ * first level initialization:
+ *
+ * 0) If clock cntrl reset switch is already set, we're recovering from
+ * "divider reset"; goto 3.
+ * 1) Setup divide ratios.
+ * 2) Reset.
+ * 3) Setup pll's, wait for lock.
+ *
+ *****************************************************************************/
+
+.macro pbl_ar9344_v11_pll_config
+ .set push
+ .set noreorder
+
+ pbl_reg_writel 0x13210f00, DPLL2_ADDRESS_c4
+ pbl_reg_writel 0x03000000, CPU_DPLL3_ADDRESS
+ pbl_reg_writel 0x13210f00, DPLL2_ADDRESS_44
+ pbl_reg_writel 0x03000000, DDR_DPLL3_ADDRESS
+ pbl_reg_writel 0x03000000, DPLL3_ADDRESS_88
+
+ li t5, KSEG1ADDR(WASP_BOOTSTRAP_REG);
+ li t6, WASP_REF_CLK_25
+ lw t7, 0(t5);
+ and t6, t7, t6
+ beq zero, t6, setup_ref25_val
+ nop
+
+setup_ref40_val:
+ li t5, CPU_PLL_CONFIG_NINT_VAL_40
+ li t6, DDR_PLL_CONFIG_NINT_VAL_40
+ li t7, CPU_PLL_NFRAC_40
+ li t9, DDR_PLL_NFRAC_40
+ b 1f
+ nop
+
+setup_ref25_val:
+ li t5, CPU_PLL_CONFIG_NINT_VAL_25
+ li t6, DDR_PLL_CONFIG_NINT_VAL_25
+ li t7, CPU_PLL_NFRAC_25
+ li t9, DDR_PLL_NFRAC_25
+
+1:
+ li t4, (CPU_PLL_DITHER_DITHER_EN_SET(0) | \
+ CPU_PLL_DITHER_NFRAC_STEP_SET(1) | \
+ CPU_PLL_DITHER_UPDATE_COUNT_SET(0xf));
+ or t4, t4, t7
+
+ li t8, 0x21000;
+ or t5, t5, t8
+
+ li t8, 0x210000;
+ or t6, t6, t8
+
+ li t3, (DDR_PLL_DITHER_DITHER_EN_SET(0) | \
+ DDR_PLL_DITHER_NFRAC_STEP_SET(1) | \
+ DDR_PLL_DITHER_UPDATE_COUNT_SET(0xf));
+
+ or t3, t3, t9
+
+pll_bypass_set:
+ /* reg, mask, val */
+ /* 0xb8050008, 0xfffffffb, 0x4 */
+ cpu_ddr_control_set(CPU_DDR_CLOCK_CONTROL_CPU_PLL_BYPASS_MASK, \
+ CPU_DDR_CLOCK_CONTROL_CPU_PLL_BYPASS_SET(1));
+ /* 0xb8050008, 0xfffffff7, 0x8 */
+ cpu_ddr_control_set(CPU_DDR_CLOCK_CONTROL_DDR_PLL_BYPASS_MASK, \
+ CPU_DDR_CLOCK_CONTROL_DDR_PLL_BYPASS_SET(1));
+ /* 0xb8050008, 0xffffffef, 0x10 */
+ cpu_ddr_control_set(CPU_DDR_CLOCK_CONTROL_AHB_PLL_BYPASS_MASK, \
+ CPU_DDR_CLOCK_CONTROL_AHB_PLL_BYPASS_SET(1));
+
+init_cpu_pll:
+ li t7, AR934X_CPU_PLL_CONFIG
+ li t8, CPU_PLL_CONFIG_PLLPWD_SET(1)
+ or t8, t8, t5
+ sw t8, 0(t7);
+
+init_ddr_pll:
+ li t7, AR934X_DDR_PLL_CONFIG
+ li t8, DDR_PLL_CONFIG_PLLPWD_SET(1)
+ or t8, t8, t6
+ sw t8, 0(t7);
+
+init_ahb_pll:
+ pbl_reg_writel 0x0130801C, AR934X_CPU_DDR_CLOCK_CONTROL
+
+srif_set:
+ /* Use built in values, based on ref clock */
+ li t5, KSEG1ADDR(WASP_BOOTSTRAP_REG);
+ li t6, WASP_REF_CLK_25
+ lw t7, 0(t5);
+ and t6, t7, t6
+ /* jump to 25ref clk */
+ beq zero, t6, 1f
+ nop
+
+ /* refdiv nint nfrac */
+ /* cpu freq = (40 MHz refclk/refdiv 8) * Nint */
+ li t4, ((0x8 << 27) | (112 << 18) | 0);
+ /* ddr freq = (40 MHz refclk/refdiv 8) * Nint */
+ li t5, ((0x8 << 27) | (90 << 18) | 0);
+ b 2f
+ nop
+1:
+
+ /* cpu freq = (25 MHz refclk/refdiv 5) * Nint */
+ li t4, ((0x5 << 27) | (112 << 18) | 0);
+ /* ddr freq = (25 MHz refclk/refdiv 5) * Nint */
+ li t5, ((0x5 << 27) | (90 << 18) | 0);
+
+2:
+
+ /* 0 to 0xbd000004 */
+ clear_loop_count(ATH_CPU_COUNT_LOC);
+
+cpu_pll_is_not_locked:
+ inc_loop_count(ATH_CPU_COUNT_LOC);
+
+ pbl_reg_writel 0x10810F00, DPLL2_ADDRESS_c4
+
+ set_srif_pll_reg(0xb81161c0, t4);
+
+ pbl_reg_writel 0xd0810f00, DPLL2_ADDRESS_c4
+ pbl_reg_writel 0x03000000, CPU_DPLL3_ADDRESS
+ pbl_reg_writel 0xd0800f00, DPLL2_ADDRESS_c4
+
+cpu_clear_do_meas1:
+ li t7, KSEG1ADDR(CPU_DPLL3_ADDRESS)
+ lw t8, 0(t7)
+ li t9, ~CPU_DPLL3_DO_MEAS_SET(1)
+ and t8, t8, t9
+ sw t8, 0(t7)
+
+cpu_set_do_meas:
+ li t7, KSEG1ADDR(CPU_DPLL3_ADDRESS)
+ lw t8, 0(t7)
+ li t9, CPU_DPLL3_DO_MEAS_SET(1)
+ or t8, t8, t9
+ sw t8, 0(t7)
+
+ li t7, KSEG1ADDR(CPU_DPLL4_ADDRESS)
+cpu_wait_for_meas_done:
+ lw t8, 0(t7)
+ andi t8, t8, CPU_DPLL4_MEAS_DONE_SET(1)
+ beqz t8, cpu_wait_for_meas_done
+ nop
+
+cpu_clear_do_meas2:
+ li t7, KSEG1ADDR(CPU_DPLL3_ADDRESS)
+ lw t8, 0(t7)
+ li t9, ~CPU_DPLL3_DO_MEAS_SET(1)
+ and t8, t8, t9
+ sw t8, 0(t7)
+
+cpu_read_sqsum_dvc:
+ li t7, KSEG1ADDR(CPU_DPLL3_ADDRESS)
+ lw t8, 0(t7)
+ li t9, CPU_DPLL3_SQSUM_DVC_MASK
+ and t8, t8, t9
+ sra t8, t8, CPU_DPLL3_SQSUM_DVC_LSB
+ li t9, 0x40000
+ subu t8, t8, t9
+ bgez t8, cpu_pll_is_not_locked
+ nop
+
+ /* DDR */
+ clear_loop_count(ATH_DDR_COUNT_LOC)
+
+ddr_pll_is_not_locked:
+
+ inc_loop_count(ATH_DDR_COUNT_LOC)
+
+ pbl_reg_writel 0x10810F00, DPLL2_ADDRESS_44
+
+ set_srif_pll_reg(0xb8116240, t5);
+
+ pbl_reg_writel 0xD0810F00, DPLL2_ADDRESS_44
+ pbl_reg_writel 0x03000000, DDR_DPLL3_ADDRESS
+ pbl_reg_writel 0xD0800F00, DPLL2_ADDRESS_44
+
+ddr_clear_do_meas1:
+ li t7, DDR_DPLL3_ADDRESS
+ lw t8, 0(t7)
+ li t9, ~DDR_DPLL3_DO_MEAS_SET(1)
+ and t8, t8, t9
+ sw t8, 0(t7)
+
+
+ddr_set_do_meas:
+ li t7, DDR_DPLL3_ADDRESS
+ lw t8, 0(t7)
+ li t9, DDR_DPLL3_DO_MEAS_SET(1)
+ or t8, t8, t9
+ sw t8, 0(t7)
+
+ li t7, KSEG1ADDR(DDR_DPLL4_ADDRESS)
+ddr_wait_for_meas_done:
+ lw t8, 0(t7)
+ andi t8, t8, DDR_DPLL4_MEAS_DONE_SET(1)
+ beqz t8, ddr_wait_for_meas_done
+ nop
+
+ddr_clear_do_meas2:
+ li t7, DDR_DPLL3_ADDRESS
+ lw t8, 0(t7)
+ li t9, ~DDR_DPLL3_DO_MEAS_SET(1)
+ and t8, t8, t9
+ sw t8, 0(t7)
+
+ddr_read_sqsum_dvc:
+ li t7, DDR_DPLL3_ADDRESS
+ lw t8, 0(t7)
+ li t9, DDR_DPLL3_SQSUM_DVC_MASK
+ and t8, t8, t9
+ sra t8, t8, DDR_DPLL3_SQSUM_DVC_LSB
+ li t9, 0x40000
+ subu t8, t8, t9
+ bgez t8, ddr_pll_is_not_locked
+ nop
+
+pll_bypass_unset:
+ cpu_ddr_control_set(CPU_DDR_CLOCK_CONTROL_CPU_PLL_BYPASS_MASK, \
+ CPU_DDR_CLOCK_CONTROL_CPU_PLL_BYPASS_SET(0));
+ cpu_ddr_control_set(CPU_DDR_CLOCK_CONTROL_DDR_PLL_BYPASS_MASK, \
+ CPU_DDR_CLOCK_CONTROL_DDR_PLL_BYPASS_SET(0));
+ cpu_ddr_control_set(CPU_DDR_CLOCK_CONTROL_AHB_PLL_BYPASS_MASK, \
+ CPU_DDR_CLOCK_CONTROL_AHB_PLL_BYPASS_SET(0));
+
+ddr_pll_dither_unset:
+ pbl_reg_writel 0x78180200, AR934X_DDR_PLL_DITHER
+
+cpu_pll_dither_unset:
+ li t7, AR934X_CPU_PLL_DITHER
+ sw t4, 0(t7)
+
+ .set pop
+.endm
+
+#define AR9344_DDR_DDR2_CONFIG AR7240_DDR_CTL_BASE+0xb8
+#define CFG_934X_DDR2_EN_TWL_VAL 0x0e59
+#define USEC_MULT 1
+#define CFG_934X_DDR2_CONFIG_VAL 0xc7d48cd0
+#define CFG_934X_DDR2_CONFIG2_VAL 0x9dd0e6a8
+#define CFG_934X_DDR2_MODE_VAL_INIT 0x133
+#define CFG_934X_DDR2_EXT_MODE_VAL_INIT 0x382
+#define CFG_934X_DDR2_EXT_MODE_VAL 0x402
+#define CFG_934X_DDR2_MODE_VAL 0x33
+#define CFG_DDR_REFRESH_VAL 0x4270
+#define CFG_934X_DDR2_TAP_VAL 0x10012
+#define CFG_DDR2_RD_DATA_THIS_CYCLE_VAL_32 0xff
+#define CFG_DDR2_RD_DATA_THIS_CYCLE_VAL_16 0xffff
+
+.macro pbl_ar9344_v11_ddr2_config
+ .set push
+ .set noreorder
+
+ pbl_reg_writel CFG_934X_DDR2_EN_TWL_VAL, AR9344_DDR_DDR2_CONFIG
+ pbl_sleep t2, 100 * USEC_MULT
+
+ pbl_reg_writel 0x10, AR7240_DDR_CONTROL
+ pbl_sleep t2, 10 * USEC_MULT
+
+ pbl_reg_writel 0x20, AR7240_DDR_CONTROL
+ pbl_sleep t2, 10 * USEC_MULT
+
+ li t5, KSEG1ADDR(WASP_BOOTSTRAP_REG);
+ li t6, BIT(3)
+ lw t7, 0(t5);
+ and t6, t7, t6
+ beq zero, t6, setup_16bit_1
+ nop
+setup_32bit_1:
+ pbl_reg_writel BIT(6), AR7240_DDR_CTL_CONFIG
+ b 1f
+ nop
+setup_16bit_1:
+ pbl_reg_clr BIT(6), AR7240_DDR_CTL_CONFIG
+1:
+
+ pbl_sleep t2, 10 * USEC_MULT
+
+ pbl_reg_writel CFG_934X_DDR2_CONFIG_VAL, AR7240_DDR_CONFIG
+ pbl_sleep t2, 100 * USEC_MULT
+
+ pbl_reg_writel CFG_934X_DDR2_CONFIG2_VAL, AR7240_DDR_CONFIG2
+ pbl_sleep t2, 100 * USEC_MULT
+
+ pbl_reg_writel 0x8, AR7240_DDR_CONTROL
+ pbl_sleep t2, 10 * USEC_MULT
+
+ pbl_reg_writel CFG_934X_DDR2_MODE_VAL_INIT, AR7240_DDR_MODE
+ pbl_sleep t2, 1000 * USEC_MULT
+
+ pbl_reg_writel 0x1, AR7240_DDR_CONTROL
+ pbl_sleep t2, 10 * USEC_MULT
+
+ pbl_reg_writel CFG_934X_DDR2_EXT_MODE_VAL_INIT, AR7240_DDR_EXT_MODE
+ pbl_sleep t2, 100 * USEC_MULT
+
+ pbl_reg_writel 0x2, AR7240_DDR_CONTROL
+ pbl_sleep t2, 10 * USEC_MULT
+
+ pbl_reg_writel CFG_934X_DDR2_EXT_MODE_VAL, AR7240_DDR_EXT_MODE
+ pbl_sleep t2, 100 * USEC_MULT
+
+ pbl_reg_writel 0x2, AR7240_DDR_CONTROL
+ pbl_sleep t2, 10 * USEC_MULT
+
+ pbl_reg_writel 0x8, AR7240_DDR_CONTROL
+ pbl_sleep t2, 10 * USEC_MULT
+
+ pbl_reg_writel CFG_934X_DDR2_MODE_VAL, AR7240_DDR_MODE
+ pbl_sleep t2, 100 * USEC_MULT
+
+ pbl_reg_writel 0x1, AR7240_DDR_CONTROL
+ pbl_sleep t2, 10 * USEC_MULT
+
+ pbl_reg_writel CFG_DDR_REFRESH_VAL, AR7240_DDR_REFRESH
+ pbl_sleep t2, 100 * USEC_MULT
+
+ pbl_reg_writel CFG_934X_DDR2_TAP_VAL, AR7240_DDR_TAP_CONTROL0
+ pbl_reg_writel CFG_934X_DDR2_TAP_VAL, AR7240_DDR_TAP_CONTROL1
+
+
+ li t5, KSEG1ADDR(WASP_BOOTSTRAP_REG);
+ li t6, BIT(3)
+ lw t7, 0(t5);
+ and t6, t7, t6
+ beq zero, t6, setup_16bit_2
+ nop
+setup_32bit_2:
+ pbl_reg_writel CFG_934X_DDR2_TAP_VAL, AR7240_DDR_TAP_CONTROL2
+ pbl_reg_writel CFG_934X_DDR2_TAP_VAL, AR7240_DDR_TAP_CONTROL3
+ pbl_reg_writel CFG_DDR2_RD_DATA_THIS_CYCLE_VAL_32, AR7240_DDR_RD_DATA_THIS_CYCLE
+ b 1f
+ nop
+setup_16bit_2:
+ pbl_reg_writel CFG_DDR2_RD_DATA_THIS_CYCLE_VAL_16, AR7240_DDR_RD_DATA_THIS_CYCLE
+
+1:
+ pbl_sleep t2, 100 * USEC_MULT
+
+ pbl_reg_writel 0x74444444, AR7240_DDR_BURST
+ pbl_sleep t2, 100 * USEC_MULT
+
+ pbl_reg_writel 0x222, AR7240_DDR_BURST2
+ pbl_sleep t2, 100 * USEC_MULT
+
+ pbl_reg_writel 0xfffff, AR7240_AHB_MASTER_TIMEOUT
+ pbl_sleep t2, 100 * USEC_MULT
+
+ .set pop
+.endm
+
+#endif /* __ASM_MACH_ATH79_PBL_LL_INIT_AR9344_1_1_H */
--
2.11.0
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v1 3/3] MIPS: ath79: add TP-Link WDR4300 board support
2017-08-09 15:51 [PATCH v1 0/3] provide basic support for TP-Link WDR4300 Oleksij Rempel
2017-08-09 15:51 ` [PATCH v1 1/3] MIPS: ath79: provide CONFIG_SOC_QCA_AR9331 option Oleksij Rempel
2017-08-09 15:51 ` [PATCH v1 2/3] MIPS: ath79: add initial QCA AR9344 SoC support Oleksij Rempel
@ 2017-08-09 15:51 ` Oleksij Rempel
2 siblings, 0 replies; 6+ messages in thread
From: Oleksij Rempel @ 2017-08-09 15:51 UTC (permalink / raw)
To: barebox; +Cc: Oleksij Rempel
This provides low level initialization of pll and ddr2. Resulting binary
should work from SRAM, DDR2 and SPI flash. If started from DDR2 RAM
level initialization will skipped.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
---
arch/mips/Makefile | 1 +
arch/mips/boards/tplink-wdr4300/Makefile | 1 +
arch/mips/boards/tplink-wdr4300/board.c | 28 ++++++++
.../tplink-wdr4300/include/board/board_pbl_start.h | 62 +++++++++++++++++
arch/mips/configs/tplink-wdr4300_defconfig | 78 ++++++++++++++++++++++
arch/mips/dts/ar9344_tl_wdr4300.dts | 63 +++++++++++++++++
arch/mips/mach-ath79/Kconfig | 10 +++
7 files changed, 243 insertions(+)
create mode 100644 arch/mips/boards/tplink-wdr4300/Makefile
create mode 100644 arch/mips/boards/tplink-wdr4300/board.c
create mode 100644 arch/mips/boards/tplink-wdr4300/include/board/board_pbl_start.h
create mode 100644 arch/mips/configs/tplink-wdr4300_defconfig
create mode 100644 arch/mips/dts/ar9344_tl_wdr4300.dts
diff --git a/arch/mips/Makefile b/arch/mips/Makefile
index 75761b5e7..dd5ceea20 100644
--- a/arch/mips/Makefile
+++ b/arch/mips/Makefile
@@ -80,6 +80,7 @@ board-$(CONFIG_BOARD_NETGEAR_WG102) := netgear-wg102
machine-$(CONFIG_MACH_MIPS_ATH79) := ath79
board-$(CONFIG_BOARD_TPLINK_MR3020) := tplink-mr3020
+board-$(CONFIG_BOARD_TPLINK_WDR4300) := tplink-wdr4300
board-$(CONFIG_BOARD_BLACK_SWIFT) := black-swift
machine-$(CONFIG_MACH_MIPS_BCM47XX) := bcm47xx
diff --git a/arch/mips/boards/tplink-wdr4300/Makefile b/arch/mips/boards/tplink-wdr4300/Makefile
new file mode 100644
index 000000000..dcfc2937d
--- /dev/null
+++ b/arch/mips/boards/tplink-wdr4300/Makefile
@@ -0,0 +1 @@
+obj-y += board.o
diff --git a/arch/mips/boards/tplink-wdr4300/board.c b/arch/mips/boards/tplink-wdr4300/board.c
new file mode 100644
index 000000000..d6126fcb6
--- /dev/null
+++ b/arch/mips/boards/tplink-wdr4300/board.c
@@ -0,0 +1,28 @@
+/*
+ * Copyright (C) 2017 Oleksij Rempel <o.rempel@pengutronix.de>
+ * Copyright (C) 2014 Antony Pavlov <antonynpavlov@gmail.com>
+ *
+ * This file is part of barebox.
+ * See file CREDITS for list of people who contributed to this project.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <common.h>
+#include <init.h>
+
+static int model_hostname_init(void)
+{
+ barebox_set_hostname("wdr4300");
+
+ return 0;
+}
+postcore_initcall(model_hostname_init);
diff --git a/arch/mips/boards/tplink-wdr4300/include/board/board_pbl_start.h b/arch/mips/boards/tplink-wdr4300/include/board/board_pbl_start.h
new file mode 100644
index 000000000..7d4ee4bab
--- /dev/null
+++ b/arch/mips/boards/tplink-wdr4300/include/board/board_pbl_start.h
@@ -0,0 +1,62 @@
+/*
+ * Copyright (C) 2017 Oleksij Rempel <o.rempel@pengutronix.de>
+ *
+ * This file is part of barebox.
+ * See file CREDITS for list of people who contributed to this project.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <mach/debug_ll_ar9344.h>
+#include <asm/pbl_macros.h>
+#include <mach/pbl_macros.h>
+#include <mach/pbl_ll_init_ar9344_1.1.h>
+#include <asm/pbl_nmon.h>
+
+ .macro board_pbl_start
+ .set push
+ .set noreorder
+
+ mips_barebox_10h
+
+ debug_ll_ar9344_init
+
+ debug_ll_outc '1'
+
+ hornet_mips24k_cp0_setup
+ debug_ll_outc '2'
+
+ /* test if we are in the SRAM */
+ pbl_blt 0xbd000000 1f t8
+ debug_ll_outc '3'
+ b skip_flash_test
+ nop
+1:
+ /* test if we are in the flash */
+ pbl_blt 0xbf000000 skip_pll_ram_config t8
+ debug_ll_outc '4'
+skip_flash_test:
+
+ pbl_ar9344_v11_pll_config
+ debug_ll_outc '5'
+
+ pbl_ar9344_v11_ddr2_config
+
+skip_pll_ram_config:
+ debug_ll_outc '6'
+ debug_ll_outnl
+
+ mips_nmon
+
+ copy_to_link_location pbl_start
+
+ .set pop
+ .endm
diff --git a/arch/mips/configs/tplink-wdr4300_defconfig b/arch/mips/configs/tplink-wdr4300_defconfig
new file mode 100644
index 000000000..63189b754
--- /dev/null
+++ b/arch/mips/configs/tplink-wdr4300_defconfig
@@ -0,0 +1,78 @@
+CONFIG_BUILTIN_DTB=y
+CONFIG_BUILTIN_DTB_NAME="ar9344_tl_wdr4300"
+CONFIG_MACH_MIPS_ATH79=y
+CONFIG_BOARD_TPLINK_WDR4300=y
+CONFIG_PBL_IMAGE=y
+CONFIG_IMAGE_COMPRESSION_XZKERN=y
+CONFIG_MMU=y
+CONFIG_TEXT_BASE=0x81000000
+CONFIG_MALLOC_TLSF=y
+CONFIG_HUSH_FANCY_PROMPT=y
+CONFIG_CMDLINE_EDITING=y
+CONFIG_AUTO_COMPLETE=y
+CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW=y
+CONFIG_CMD_DMESG=y
+CONFIG_LONGHELP=y
+CONFIG_CMD_IOMEM=y
+CONFIG_CMD_IMD=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_GO=y
+CONFIG_CMD_LOADB=y
+CONFIG_CMD_LOADY=y
+CONFIG_CMD_RESET=y
+CONFIG_CMD_EXPORT=y
+CONFIG_CMD_DEFAULTENV=y
+CONFIG_CMD_LOADENV=y
+CONFIG_CMD_MAGICVAR=y
+CONFIG_CMD_MAGICVAR_HELP=y
+CONFIG_CMD_SAVEENV=y
+CONFIG_CMD_SHA1SUM=y
+CONFIG_CMD_UNCOMPRESS=y
+CONFIG_CMD_LET=y
+CONFIG_CMD_MSLEEP=y
+CONFIG_CMD_READF=y
+CONFIG_CMD_SLEEP=y
+CONFIG_CMD_ECHO_E=y
+CONFIG_CMD_EDIT=y
+CONFIG_CMD_READLINE=y
+CONFIG_CMD_TIMEOUT=y
+CONFIG_CMD_CRC=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_MM=y
+CONFIG_CMD_CLK=y
+CONFIG_CMD_DETECT=y
+CONFIG_CMD_FLASH=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_LED=y
+CONFIG_CMD_POWEROFF=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_LED_TRIGGER=y
+CONFIG_CMD_BAREBOX_UPDATE=y
+CONFIG_CMD_OF_NODE=y
+CONFIG_CMD_OF_PROPERTY=y
+CONFIG_CMD_OFTREE=y
+CONFIG_CMD_TIME=y
+CONFIG_NET=y
+CONFIG_NET_NFS=y
+CONFIG_NET_NETCONSOLE=y
+CONFIG_NET_RESOLV=y
+CONFIG_NET_DHCP=y
+CONFIG_NET_SNTP=y
+CONFIG_OFDEVICE=y
+CONFIG_OF_BAREBOX_DRIVERS=y
+CONFIG_OF_BAREBOX_ENV_IN_FS=y
+CONFIG_DRIVER_SERIAL_NS16550=y
+CONFIG_DRIVER_NET_AG71XX=y
+CONFIG_AT803X_PHY=y
+CONFIG_MDIO_BITBANG=y
+CONFIG_MDIO_GPIO=y
+CONFIG_DRIVER_SPI_ATH79=y
+CONFIG_MTD=y
+# CONFIG_MTD_OOB_DEVICE is not set
+CONFIG_MTD_M25P80=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_LED_GPIO_OF=y
+CONFIG_LED_TRIGGERS=y
+CONFIG_DIGEST_SHA224_GENERIC=y
+CONFIG_DIGEST_SHA256_GENERIC=y
diff --git a/arch/mips/dts/ar9344_tl_wdr4300.dts b/arch/mips/dts/ar9344_tl_wdr4300.dts
new file mode 100644
index 000000000..b02c1d730
--- /dev/null
+++ b/arch/mips/dts/ar9344_tl_wdr4300.dts
@@ -0,0 +1,63 @@
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar9344.dtsi"
+
+/ {
+ model = "TP-Link WDR4300";
+ compatible = "tplink,tl-wdr4300";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x8000000>;
+ };
+
+ chosen {
+ stdout-path = &uart0;
+
+ environment@0 {
+ compatible = "barebox,environment";
+ device-path = &spiflash, "partname:barebox-environment";
+ };
+ };
+};
+
+&ref {
+ clock-frequency = <40000000>;
+};
+
+&uart0 {
+ status = "okay";
+ clock-frequency = <40000000>;
+};
+
+&spi {
+ num-chipselects = <1>;
+ status = "okay";
+
+ /* Winbond W25Q64CV SPI flash */
+ spiflash: w25q64cv@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor", "winbond,w25q64cv";
+ spi-max-frequency = <104000000>;
+ reg = <0>;
+
+ partition@0 {
+ label = "barebox";
+ reg = <0 0x80000>;
+ read-only;
+ };
+
+ partition@80000 {
+ label = "barebox-environment";
+ reg = <0x80000 0x10000>;
+ };
+ };
+};
diff --git a/arch/mips/mach-ath79/Kconfig b/arch/mips/mach-ath79/Kconfig
index f2eae2532..9fec00c98 100644
--- a/arch/mips/mach-ath79/Kconfig
+++ b/arch/mips/mach-ath79/Kconfig
@@ -7,6 +7,9 @@ config ARCH_TEXT_BASE
config SOC_QCA_AR9331
bool
+config SOC_QCA_AR9344
+ bool
+
choice
prompt "Board type"
@@ -17,6 +20,13 @@ config BOARD_TPLINK_MR3020
select HAVE_IMAGE_COMPRESSION
select HAS_NMON
+config BOARD_TPLINK_WDR4300
+ bool "TP-LINK WDR4300"
+ select SOC_QCA_AR9344
+ select HAVE_PBL_IMAGE
+ select HAVE_IMAGE_COMPRESSION
+ select HAS_NMON
+
config BOARD_BLACK_SWIFT
bool "Black Swift"
select SOC_QCA_AR9331
--
2.11.0
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v1 3/3] MIPS: ath79: add TP-Link WDR4300 board support
2017-08-01 18:06 ` [PATCH v1 3/3] MIPS: ath79: add TP-Link WDR4300 board support Oleksij Rempel
@ 2017-08-03 14:30 ` Oleksij Rempel
0 siblings, 0 replies; 6+ messages in thread
From: Oleksij Rempel @ 2017-08-03 14:30 UTC (permalink / raw)
To: barebox
[-- Attachment #1.1.1: Type: text/plain, Size: 8529 bytes --]
Am 01.08.2017 um 20:06 schrieb Oleksij Rempel:
> This provides low level initialization of pll and ddr2. Resulting binary
> should work from SRAM, DDR2 and SPI flash. If started from DDR2 RAM
> level initialization will skipped.
>
> Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
> ---
> arch/mips/Makefile | 1 +
> arch/mips/boards/tplink-wdr4300/Makefile | 1 +
> arch/mips/boards/tplink-wdr4300/board.c | 28 ++++++++++
> .../tplink-wdr4300/include/board/board_pbl_start.h | 62 ++++++++++++++++++++++
> arch/mips/configs/tplink-wdr4300_defconfig | 50 +++++++++++++++++
> arch/mips/dts/ar9344_tl_wdr3400.dts | 47 ++++++++++++++++
> arch/mips/mach-ath79/Kconfig | 10 ++++
> 7 files changed, 199 insertions(+)
> create mode 100644 arch/mips/boards/tplink-wdr4300/Makefile
> create mode 100644 arch/mips/boards/tplink-wdr4300/board.c
> create mode 100644 arch/mips/boards/tplink-wdr4300/include/board/board_pbl_start.h
> create mode 100644 arch/mips/configs/tplink-wdr4300_defconfi
> create mode 100644 arch/mips/dts/ar9344_tl_wdr3400.dts
DTS file has wrong name. Should be wdr4300 instead of wdr3400
> diff --git a/arch/mips/Makefile b/arch/mips/Makefile
> index 75761b5e7..dd5ceea20 100644
> --- a/arch/mips/Makefile
> +++ b/arch/mips/Makefile
> @@ -80,6 +80,7 @@ board-$(CONFIG_BOARD_NETGEAR_WG102) := netgear-wg102
>
> machine-$(CONFIG_MACH_MIPS_ATH79) := ath79
> board-$(CONFIG_BOARD_TPLINK_MR3020) := tplink-mr3020
> +board-$(CONFIG_BOARD_TPLINK_WDR4300) := tplink-wdr4300
> board-$(CONFIG_BOARD_BLACK_SWIFT) := black-swift
>
> machine-$(CONFIG_MACH_MIPS_BCM47XX) := bcm47xx
> diff --git a/arch/mips/boards/tplink-wdr4300/Makefile b/arch/mips/boards/tplink-wdr4300/Makefile
> new file mode 100644
> index 000000000..dcfc2937d
> --- /dev/null
> +++ b/arch/mips/boards/tplink-wdr4300/Makefile
> @@ -0,0 +1 @@
> +obj-y += board.o
> diff --git a/arch/mips/boards/tplink-wdr4300/board.c b/arch/mips/boards/tplink-wdr4300/board.c
> new file mode 100644
> index 000000000..d6126fcb6
> --- /dev/null
> +++ b/arch/mips/boards/tplink-wdr4300/board.c
> @@ -0,0 +1,28 @@
> +/*
> + * Copyright (C) 2017 Oleksij Rempel <o.rempel@pengutronix.de>
> + * Copyright (C) 2014 Antony Pavlov <antonynpavlov@gmail.com>
> + *
> + * This file is part of barebox.
> + * See file CREDITS for list of people who contributed to this project.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2
> + * as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + */
> +
> +#include <common.h>
> +#include <init.h>
> +
> +static int model_hostname_init(void)
> +{
> + barebox_set_hostname("wdr4300");
> +
> + return 0;
> +}
> +postcore_initcall(model_hostname_init);
> diff --git a/arch/mips/boards/tplink-wdr4300/include/board/board_pbl_start.h b/arch/mips/boards/tplink-wdr4300/include/board/board_pbl_start.h
> new file mode 100644
> index 000000000..7d4ee4bab
> --- /dev/null
> +++ b/arch/mips/boards/tplink-wdr4300/include/board/board_pbl_start.h
> @@ -0,0 +1,62 @@
> +/*
> + * Copyright (C) 2017 Oleksij Rempel <o.rempel@pengutronix.de>
> + *
> + * This file is part of barebox.
> + * See file CREDITS for list of people who contributed to this project.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2
> + * as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + */
> +
> +#include <mach/debug_ll_ar9344.h>
> +#include <asm/pbl_macros.h>
> +#include <mach/pbl_macros.h>
> +#include <mach/pbl_ll_init_ar9344_1.1.h>
> +#include <asm/pbl_nmon.h>
> +
> + .macro board_pbl_start
> + .set push
> + .set noreorder
> +
> + mips_barebox_10h
> +
> + debug_ll_ar9344_init
> +
> + debug_ll_outc '1'
> +
> + hornet_mips24k_cp0_setup
> + debug_ll_outc '2'
> +
> + /* test if we are in the SRAM */
> + pbl_blt 0xbd000000 1f t8
> + debug_ll_outc '3'
> + b skip_flash_test
> + nop
> +1:
> + /* test if we are in the flash */
> + pbl_blt 0xbf000000 skip_pll_ram_config t8
> + debug_ll_outc '4'
> +skip_flash_test:
> +
> + pbl_ar9344_v11_pll_config
> + debug_ll_outc '5'
> +
> + pbl_ar9344_v11_ddr2_config
> +
> +skip_pll_ram_config:
> + debug_ll_outc '6'
> + debug_ll_outnl
> +
> + mips_nmon
> +
> + copy_to_link_location pbl_start
> +
> + .set pop
> + .endm
> diff --git a/arch/mips/configs/tplink-wdr4300_defconfig b/arch/mips/configs/tplink-wdr4300_defconfig
> new file mode 100644
> index 000000000..9114b86db
> --- /dev/null
> +++ b/arch/mips/configs/tplink-wdr4300_defconfig
> @@ -0,0 +1,50 @@
> +CONFIG_BUILTIN_DTB=y
> +CONFIG_BUILTIN_DTB_NAME="ar9344_tl_wdr3400"
> +CONFIG_MACH_MIPS_ATH79=y
> +CONFIG_BOARD_TPLINK_WDR4300=y
> +CONFIG_PBL_IMAGE=y
> +CONFIG_IMAGE_COMPRESSION_XZKERN=y
> +CONFIG_MMU=y
> +CONFIG_TEXT_BASE=0xbfc00000
> +CONFIG_MALLOC_TLSF=y
> +CONFIG_CMDLINE_EDITING=y
> +CONFIG_AUTO_COMPLETE=y
> +CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW=y
> +CONFIG_DEBUG_INFO=y
> +CONFIG_DEBUG_LL=y
> +CONFIG_DEBUG_INITCALLS=y
> +CONFIG_LONGHELP=y
> +CONFIG_CMD_IOMEM=y
> +CONFIG_CMD_MEMINFO=y
> +CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW=y
> +# CONFIG_CMD_BOOTM is not set
> +CONFIG_CMD_GO=y
> +CONFIG_CMD_LOADB=y
> +CONFIG_CMD_LOADY=y
> +CONFIG_CMD_RESET=y
> +CONFIG_CMD_SHA1SUM=y
> +CONFIG_CMD_LET=y
> +CONFIG_CMD_SLEEP=y
> +CONFIG_CMD_EDIT=y
> +CONFIG_CMD_MM=y
> +CONFIG_CMD_CLK=y
> +CONFIG_CMD_FLASH=y
> +CONFIG_CMD_GPIO=y
> +CONFIG_CMD_LED=y
> +CONFIG_CMD_SPI=y
> +CONFIG_CMD_LED_TRIGGER=y
> +CONFIG_CMD_OF_NODE=y
> +CONFIG_CMD_OF_PROPERTY=y
> +CONFIG_CMD_OFTREE=y
> +CONFIG_OFDEVICE=y
> +CONFIG_DRIVER_SERIAL_NS16550=y
> +CONFIG_DRIVER_SPI_ATH79=y
> +CONFIG_MTD=y
> +# CONFIG_MTD_OOB_DEVICE is not set
> +CONFIG_MTD_M25P80=y
> +CONFIG_LED=y
> +CONFIG_LED_GPIO=y
> +CONFIG_LED_GPIO_OF=y
> +CONFIG_LED_TRIGGERS=y
> +CONFIG_DIGEST_SHA224_GENERIC=y
> +CONFIG_DIGEST_SHA256_GENERIC=y
> diff --git a/arch/mips/dts/ar9344_tl_wdr3400.dts b/arch/mips/dts/ar9344_tl_wdr3400.dts
> new file mode 100644
> index 000000000..825b4820d
> --- /dev/null
> +++ b/arch/mips/dts/ar9344_tl_wdr3400.dts
> @@ -0,0 +1,47 @@
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +#include "ar9344.dtsi"
> +
> +/ {
> + model = "TP-Link WDR4300";
> + compatible = "tplink,tl-wdr4300";
> +
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + memory@0 {
> + device_type = "memory";
> + reg = <0x0 0x8000000>;
> + };
> +
> + chosen {
> + stdout-path = &uart0;
> + };
> +};
> +
> +&ref {
> + clock-frequency = <40000000>;
> +};
> +
> +&uart0 {
> + status = "okay";
> + clock-frequency = <40000000>;
> +};
> +
> +&spi {
> + num-chipselects = <1>;
> + status = "okay";
> +
> + /* Winbond W25Q64CV SPI flash */
> + spiflash: w25q64cv@0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "winbond,w25q64cv", "jedec,spi-nor";
> + spi-max-frequency = <104000000>;
> + reg = <0>;
> + };
> +};
> diff --git a/arch/mips/mach-ath79/Kconfig b/arch/mips/mach-ath79/Kconfig
> index f2eae2532..9fec00c98 100644
> --- a/arch/mips/mach-ath79/Kconfig
> +++ b/arch/mips/mach-ath79/Kconfig
> @@ -7,6 +7,9 @@ config ARCH_TEXT_BASE
> config SOC_QCA_AR9331
> bool
>
> +config SOC_QCA_AR9344
> + bool
> +
> choice
> prompt "Board type"
>
> @@ -17,6 +20,13 @@ config BOARD_TPLINK_MR3020
> select HAVE_IMAGE_COMPRESSION
> select HAS_NMON
>
> +config BOARD_TPLINK_WDR4300
> + bool "TP-LINK WDR4300"
> + select SOC_QCA_AR9344
> + select HAVE_PBL_IMAGE
> + select HAVE_IMAGE_COMPRESSION
> + select HAS_NMON
> +
> config BOARD_BLACK_SWIFT
> bool "Black Swift"
> select SOC_QCA_AR9331
>
[-- Attachment #1.2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 220 bytes --]
[-- Attachment #2: Type: text/plain, Size: 149 bytes --]
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v1 3/3] MIPS: ath79: add TP-Link WDR4300 board support
2017-08-01 18:06 [PATCH v1 0/3] provide QCA AR9344 support Oleksij Rempel
@ 2017-08-01 18:06 ` Oleksij Rempel
2017-08-03 14:30 ` Oleksij Rempel
0 siblings, 1 reply; 6+ messages in thread
From: Oleksij Rempel @ 2017-08-01 18:06 UTC (permalink / raw)
To: barebox; +Cc: Oleksij Rempel
This provides low level initialization of pll and ddr2. Resulting binary
should work from SRAM, DDR2 and SPI flash. If started from DDR2 RAM
level initialization will skipped.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
---
arch/mips/Makefile | 1 +
arch/mips/boards/tplink-wdr4300/Makefile | 1 +
arch/mips/boards/tplink-wdr4300/board.c | 28 ++++++++++
.../tplink-wdr4300/include/board/board_pbl_start.h | 62 ++++++++++++++++++++++
arch/mips/configs/tplink-wdr4300_defconfig | 50 +++++++++++++++++
arch/mips/dts/ar9344_tl_wdr3400.dts | 47 ++++++++++++++++
arch/mips/mach-ath79/Kconfig | 10 ++++
7 files changed, 199 insertions(+)
create mode 100644 arch/mips/boards/tplink-wdr4300/Makefile
create mode 100644 arch/mips/boards/tplink-wdr4300/board.c
create mode 100644 arch/mips/boards/tplink-wdr4300/include/board/board_pbl_start.h
create mode 100644 arch/mips/configs/tplink-wdr4300_defconfig
create mode 100644 arch/mips/dts/ar9344_tl_wdr3400.dts
diff --git a/arch/mips/Makefile b/arch/mips/Makefile
index 75761b5e7..dd5ceea20 100644
--- a/arch/mips/Makefile
+++ b/arch/mips/Makefile
@@ -80,6 +80,7 @@ board-$(CONFIG_BOARD_NETGEAR_WG102) := netgear-wg102
machine-$(CONFIG_MACH_MIPS_ATH79) := ath79
board-$(CONFIG_BOARD_TPLINK_MR3020) := tplink-mr3020
+board-$(CONFIG_BOARD_TPLINK_WDR4300) := tplink-wdr4300
board-$(CONFIG_BOARD_BLACK_SWIFT) := black-swift
machine-$(CONFIG_MACH_MIPS_BCM47XX) := bcm47xx
diff --git a/arch/mips/boards/tplink-wdr4300/Makefile b/arch/mips/boards/tplink-wdr4300/Makefile
new file mode 100644
index 000000000..dcfc2937d
--- /dev/null
+++ b/arch/mips/boards/tplink-wdr4300/Makefile
@@ -0,0 +1 @@
+obj-y += board.o
diff --git a/arch/mips/boards/tplink-wdr4300/board.c b/arch/mips/boards/tplink-wdr4300/board.c
new file mode 100644
index 000000000..d6126fcb6
--- /dev/null
+++ b/arch/mips/boards/tplink-wdr4300/board.c
@@ -0,0 +1,28 @@
+/*
+ * Copyright (C) 2017 Oleksij Rempel <o.rempel@pengutronix.de>
+ * Copyright (C) 2014 Antony Pavlov <antonynpavlov@gmail.com>
+ *
+ * This file is part of barebox.
+ * See file CREDITS for list of people who contributed to this project.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <common.h>
+#include <init.h>
+
+static int model_hostname_init(void)
+{
+ barebox_set_hostname("wdr4300");
+
+ return 0;
+}
+postcore_initcall(model_hostname_init);
diff --git a/arch/mips/boards/tplink-wdr4300/include/board/board_pbl_start.h b/arch/mips/boards/tplink-wdr4300/include/board/board_pbl_start.h
new file mode 100644
index 000000000..7d4ee4bab
--- /dev/null
+++ b/arch/mips/boards/tplink-wdr4300/include/board/board_pbl_start.h
@@ -0,0 +1,62 @@
+/*
+ * Copyright (C) 2017 Oleksij Rempel <o.rempel@pengutronix.de>
+ *
+ * This file is part of barebox.
+ * See file CREDITS for list of people who contributed to this project.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <mach/debug_ll_ar9344.h>
+#include <asm/pbl_macros.h>
+#include <mach/pbl_macros.h>
+#include <mach/pbl_ll_init_ar9344_1.1.h>
+#include <asm/pbl_nmon.h>
+
+ .macro board_pbl_start
+ .set push
+ .set noreorder
+
+ mips_barebox_10h
+
+ debug_ll_ar9344_init
+
+ debug_ll_outc '1'
+
+ hornet_mips24k_cp0_setup
+ debug_ll_outc '2'
+
+ /* test if we are in the SRAM */
+ pbl_blt 0xbd000000 1f t8
+ debug_ll_outc '3'
+ b skip_flash_test
+ nop
+1:
+ /* test if we are in the flash */
+ pbl_blt 0xbf000000 skip_pll_ram_config t8
+ debug_ll_outc '4'
+skip_flash_test:
+
+ pbl_ar9344_v11_pll_config
+ debug_ll_outc '5'
+
+ pbl_ar9344_v11_ddr2_config
+
+skip_pll_ram_config:
+ debug_ll_outc '6'
+ debug_ll_outnl
+
+ mips_nmon
+
+ copy_to_link_location pbl_start
+
+ .set pop
+ .endm
diff --git a/arch/mips/configs/tplink-wdr4300_defconfig b/arch/mips/configs/tplink-wdr4300_defconfig
new file mode 100644
index 000000000..9114b86db
--- /dev/null
+++ b/arch/mips/configs/tplink-wdr4300_defconfig
@@ -0,0 +1,50 @@
+CONFIG_BUILTIN_DTB=y
+CONFIG_BUILTIN_DTB_NAME="ar9344_tl_wdr3400"
+CONFIG_MACH_MIPS_ATH79=y
+CONFIG_BOARD_TPLINK_WDR4300=y
+CONFIG_PBL_IMAGE=y
+CONFIG_IMAGE_COMPRESSION_XZKERN=y
+CONFIG_MMU=y
+CONFIG_TEXT_BASE=0xbfc00000
+CONFIG_MALLOC_TLSF=y
+CONFIG_CMDLINE_EDITING=y
+CONFIG_AUTO_COMPLETE=y
+CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW=y
+CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_LL=y
+CONFIG_DEBUG_INITCALLS=y
+CONFIG_LONGHELP=y
+CONFIG_CMD_IOMEM=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW=y
+# CONFIG_CMD_BOOTM is not set
+CONFIG_CMD_GO=y
+CONFIG_CMD_LOADB=y
+CONFIG_CMD_LOADY=y
+CONFIG_CMD_RESET=y
+CONFIG_CMD_SHA1SUM=y
+CONFIG_CMD_LET=y
+CONFIG_CMD_SLEEP=y
+CONFIG_CMD_EDIT=y
+CONFIG_CMD_MM=y
+CONFIG_CMD_CLK=y
+CONFIG_CMD_FLASH=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_LED=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_LED_TRIGGER=y
+CONFIG_CMD_OF_NODE=y
+CONFIG_CMD_OF_PROPERTY=y
+CONFIG_CMD_OFTREE=y
+CONFIG_OFDEVICE=y
+CONFIG_DRIVER_SERIAL_NS16550=y
+CONFIG_DRIVER_SPI_ATH79=y
+CONFIG_MTD=y
+# CONFIG_MTD_OOB_DEVICE is not set
+CONFIG_MTD_M25P80=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_LED_GPIO_OF=y
+CONFIG_LED_TRIGGERS=y
+CONFIG_DIGEST_SHA224_GENERIC=y
+CONFIG_DIGEST_SHA256_GENERIC=y
diff --git a/arch/mips/dts/ar9344_tl_wdr3400.dts b/arch/mips/dts/ar9344_tl_wdr3400.dts
new file mode 100644
index 000000000..825b4820d
--- /dev/null
+++ b/arch/mips/dts/ar9344_tl_wdr3400.dts
@@ -0,0 +1,47 @@
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar9344.dtsi"
+
+/ {
+ model = "TP-Link WDR4300";
+ compatible = "tplink,tl-wdr4300";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x8000000>;
+ };
+
+ chosen {
+ stdout-path = &uart0;
+ };
+};
+
+&ref {
+ clock-frequency = <40000000>;
+};
+
+&uart0 {
+ status = "okay";
+ clock-frequency = <40000000>;
+};
+
+&spi {
+ num-chipselects = <1>;
+ status = "okay";
+
+ /* Winbond W25Q64CV SPI flash */
+ spiflash: w25q64cv@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "winbond,w25q64cv", "jedec,spi-nor";
+ spi-max-frequency = <104000000>;
+ reg = <0>;
+ };
+};
diff --git a/arch/mips/mach-ath79/Kconfig b/arch/mips/mach-ath79/Kconfig
index f2eae2532..9fec00c98 100644
--- a/arch/mips/mach-ath79/Kconfig
+++ b/arch/mips/mach-ath79/Kconfig
@@ -7,6 +7,9 @@ config ARCH_TEXT_BASE
config SOC_QCA_AR9331
bool
+config SOC_QCA_AR9344
+ bool
+
choice
prompt "Board type"
@@ -17,6 +20,13 @@ config BOARD_TPLINK_MR3020
select HAVE_IMAGE_COMPRESSION
select HAS_NMON
+config BOARD_TPLINK_WDR4300
+ bool "TP-LINK WDR4300"
+ select SOC_QCA_AR9344
+ select HAVE_PBL_IMAGE
+ select HAVE_IMAGE_COMPRESSION
+ select HAS_NMON
+
config BOARD_BLACK_SWIFT
bool "Black Swift"
select SOC_QCA_AR9331
--
2.11.0
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2017-08-09 15:52 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-08-09 15:51 [PATCH v1 0/3] provide basic support for TP-Link WDR4300 Oleksij Rempel
2017-08-09 15:51 ` [PATCH v1 1/3] MIPS: ath79: provide CONFIG_SOC_QCA_AR9331 option Oleksij Rempel
2017-08-09 15:51 ` [PATCH v1 2/3] MIPS: ath79: add initial QCA AR9344 SoC support Oleksij Rempel
2017-08-09 15:51 ` [PATCH v1 3/3] MIPS: ath79: add TP-Link WDR4300 board support Oleksij Rempel
-- strict thread matches above, loose matches on Subject: below --
2017-08-01 18:06 [PATCH v1 0/3] provide QCA AR9344 support Oleksij Rempel
2017-08-01 18:06 ` [PATCH v1 3/3] MIPS: ath79: add TP-Link WDR4300 board support Oleksij Rempel
2017-08-03 14:30 ` Oleksij Rempel
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox