* [PATCH v1 1/4] MIPS: ath79: ar9331: add generic RAM macro
@ 2017-12-01 12:52 Oleksij Rempel
2017-12-01 12:52 ` [PATCH v1 2/4] MIPS: add generic QCA AR9331 board Oleksij Rempel
` (2 more replies)
0 siblings, 3 replies; 6+ messages in thread
From: Oleksij Rempel @ 2017-12-01 12:52 UTC (permalink / raw)
To: barebox; +Cc: Oleksij Rempel
with this macro, we should be able to cover most of existing
ar9331 based boards.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
---
arch/mips/mach-ath79/include/mach/ar71xx_regs.h | 1 +
arch/mips/mach-ath79/include/mach/pbl_macros.h | 37 +++++++++++++++++++++++--
2 files changed, 35 insertions(+), 3 deletions(-)
diff --git a/arch/mips/mach-ath79/include/mach/ar71xx_regs.h b/arch/mips/mach-ath79/include/mach/ar71xx_regs.h
index 31d33b3c4..f73700b5b 100644
--- a/arch/mips/mach-ath79/include/mach/ar71xx_regs.h
+++ b/arch/mips/mach-ath79/include/mach/ar71xx_regs.h
@@ -139,6 +139,7 @@
#define AR71XX_RESET_FULL_CHIP BIT(24)
+#define AR933X_BOOTSTRAP_MEM_TYPE BIT(13)
#define AR933X_BOOTSTRAP_REF_CLK_40 BIT(0)
#endif /* __ASM_MACH_AR71XX_REGS_H */
diff --git a/arch/mips/mach-ath79/include/mach/pbl_macros.h b/arch/mips/mach-ath79/include/mach/pbl_macros.h
index 680fcbb86..9e4859b19 100644
--- a/arch/mips/mach-ath79/include/mach/pbl_macros.h
+++ b/arch/mips/mach-ath79/include/mach/pbl_macros.h
@@ -172,6 +172,40 @@
.set pop
.endm
+#define RESET_REG_BOOTSTRAP ((KSEG1 | AR71XX_RESET_BASE) \
+ | AR933X_RESET_REG_BOOTSTRAP)
+
+.macro pbl_ar9331_ram_generic_config
+ .set push
+ .set noreorder
+
+ li t5, RESET_REG_BOOTSTRAP
+ /* Documentation and source code of existing boot loaders disagree at
+ * this place. Doc says: MEM_TYPE[13:12]:
+ * - 00 = SDRAM
+ * - 01 = DDR1
+ * - 10 = DDR2
+ * The source code of most loaders do not care about BIT(12). So we do
+ * the same.
+ */
+ li t6, AR933X_BOOTSTRAP_MEM_TYPE
+ lw t7, 0(t5);
+ and t6, t7, t6
+ beq zero, t6, pbl_ar9331_ram_generic_ddr1
+ nop
+
+pbl_ar9331_ram_generic_ddr2:
+ pbl_ar9331_ddr2_config
+ b pbl_ar9331_ram_generic_config
+ nop
+
+pbl_ar9331_ram_generic_ddr1:
+ pbl_ar9331_ddr1_config
+
+pbl_ar9331_ram_generic_config:
+ .set pop
+.endm
+
#define GPIO_FUNC ((KSEG1 | AR71XX_GPIO_BASE) | AR71XX_GPIO_REG_FUNC)
.macro pbl_ar9331_uart_enable
@@ -179,9 +213,6 @@
| AR933X_GPIO_FUNC_RSRV15, GPIO_FUNC
.endm
-#define RESET_REG_BOOTSTRAP ((KSEG1 | AR71XX_RESET_BASE) \
- | AR933X_RESET_REG_BOOTSTRAP)
-
.macro pbl_ar9331_mdio_gpio_enable
/* Bit 18 enables MDC and MDIO function on GPIO26 and GPIO28 */
pbl_reg_set (1 << 18), RESET_REG_BOOTSTRAP
--
2.14.1
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 6+ messages in thread* [PATCH v1 2/4] MIPS: add generic QCA AR9331 board
2017-12-01 12:52 [PATCH v1 1/4] MIPS: ath79: ar9331: add generic RAM macro Oleksij Rempel
@ 2017-12-01 12:52 ` Oleksij Rempel
2017-12-05 8:00 ` Sascha Hauer
2017-12-01 12:52 ` [PATCH v1 3/4] MIPS: add support for DPTechnics DPT-Module v1 Oleksij Rempel
2017-12-01 12:52 ` [PATCH v1 4/4] MIPS: ar9331: add watchdog support Oleksij Rempel
2 siblings, 1 reply; 6+ messages in thread
From: Oleksij Rempel @ 2017-12-01 12:52 UTC (permalink / raw)
To: barebox; +Cc: Oleksij Rempel
this board may cover most of existing ar9331 boards
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
---
arch/mips/Makefile | 1 +
arch/mips/boards/qca-ar9331-generic/Makefile | 1 +
arch/mips/boards/qca-ar9331-generic/board.c | 8 ++++
.../include/board/board_pbl_start.h | 46 ++++++++++++++++++++++
arch/mips/mach-ath79/Kconfig | 7 ++++
5 files changed, 63 insertions(+)
create mode 100644 arch/mips/boards/qca-ar9331-generic/Makefile
create mode 100644 arch/mips/boards/qca-ar9331-generic/board.c
create mode 100644 arch/mips/boards/qca-ar9331-generic/include/board/board_pbl_start.h
diff --git a/arch/mips/Makefile b/arch/mips/Makefile
index dd5ceea20..c40ae6604 100644
--- a/arch/mips/Makefile
+++ b/arch/mips/Makefile
@@ -79,6 +79,7 @@ machine-$(CONFIG_MACH_MIPS_AR231X) := ar231x
board-$(CONFIG_BOARD_NETGEAR_WG102) := netgear-wg102
machine-$(CONFIG_MACH_MIPS_ATH79) := ath79
+board-$(CONFIG_BOARC_QCA_AR9331_GENERIC) := qca-ar9331-generic
board-$(CONFIG_BOARD_TPLINK_MR3020) := tplink-mr3020
board-$(CONFIG_BOARD_TPLINK_WDR4300) := tplink-wdr4300
board-$(CONFIG_BOARD_BLACK_SWIFT) := black-swift
diff --git a/arch/mips/boards/qca-ar9331-generic/Makefile b/arch/mips/boards/qca-ar9331-generic/Makefile
new file mode 100644
index 000000000..dcfc2937d
--- /dev/null
+++ b/arch/mips/boards/qca-ar9331-generic/Makefile
@@ -0,0 +1 @@
+obj-y += board.o
diff --git a/arch/mips/boards/qca-ar9331-generic/board.c b/arch/mips/boards/qca-ar9331-generic/board.c
new file mode 100644
index 000000000..7ec7ef8a5
--- /dev/null
+++ b/arch/mips/boards/qca-ar9331-generic/board.c
@@ -0,0 +1,8 @@
+#include <common.h>
+#include <init.h>
+
+static int dummy_init(void)
+{
+ return 0;
+}
+postcore_initcall(dummy_init);
diff --git a/arch/mips/boards/qca-ar9331-generic/include/board/board_pbl_start.h b/arch/mips/boards/qca-ar9331-generic/include/board/board_pbl_start.h
new file mode 100644
index 000000000..87c6a39e6
--- /dev/null
+++ b/arch/mips/boards/qca-ar9331-generic/include/board/board_pbl_start.h
@@ -0,0 +1,46 @@
+/*
+ * Copyright (C) 2017 Oleksij Rempel <linux@rempel-privat.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation.
+ */
+
+#include <asm/pbl_macros.h>
+#include <mach/pbl_macros.h>
+#include <asm/pbl_nmon.h>
+
+ .macro board_pbl_start
+ .set push
+ .set noreorder
+
+ mips_barebox_10h
+
+ pbl_blt 0xbf000000 skip_pll_ram_config t8
+
+ hornet_mips24k_cp0_setup
+
+ pbl_ar9331_wmac_enable
+
+ hornet_1_1_war
+
+ pbl_ar9331_pll
+ pbl_ar9331_ram_generic_config
+
+ /* Initialize caches... */
+ mips_cache_reset
+
+ /* ... and enable them */
+ dcache_enable
+
+skip_pll_ram_config:
+ pbl_ar9331_uart_enable
+ debug_ll_ar9331_init
+ mips_nmon
+
+ pbl_ar9331_mdio_gpio_enable
+
+ copy_to_link_location pbl_start
+
+ .set pop
+ .endm
diff --git a/arch/mips/mach-ath79/Kconfig b/arch/mips/mach-ath79/Kconfig
index 9fec00c98..0015fe029 100644
--- a/arch/mips/mach-ath79/Kconfig
+++ b/arch/mips/mach-ath79/Kconfig
@@ -13,6 +13,13 @@ config SOC_QCA_AR9344
choice
prompt "Board type"
+config BOARC_QCA_AR9331_GENERIC
+ bool "Generic QCA AR9331"
+ select SOC_QCA_AR9331
+ select HAVE_PBL_IMAGE
+ select HAVE_IMAGE_COMPRESSION
+ select HAS_NMON
+
config BOARD_TPLINK_MR3020
bool "TP-LINK MR3020"
select SOC_QCA_AR9331
--
2.14.1
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 6+ messages in thread* Re: [PATCH v1 2/4] MIPS: add generic QCA AR9331 board
2017-12-01 12:52 ` [PATCH v1 2/4] MIPS: add generic QCA AR9331 board Oleksij Rempel
@ 2017-12-05 8:00 ` Sascha Hauer
2017-12-05 11:43 ` Oleksij Rempel
0 siblings, 1 reply; 6+ messages in thread
From: Sascha Hauer @ 2017-12-05 8:00 UTC (permalink / raw)
To: Oleksij Rempel; +Cc: barebox
On Fri, Dec 01, 2017 at 01:52:49PM +0100, Oleksij Rempel wrote:
> this board may cover most of existing ar9331 boards
>
> Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
> ---
> arch/mips/Makefile | 1 +
> arch/mips/boards/qca-ar9331-generic/Makefile | 1 +
> arch/mips/boards/qca-ar9331-generic/board.c | 8 ++++
> .../include/board/board_pbl_start.h | 46 ++++++++++++++++++++++
> arch/mips/mach-ath79/Kconfig | 7 ++++
> 5 files changed, 63 insertions(+)
> create mode 100644 arch/mips/boards/qca-ar9331-generic/Makefile
> create mode 100644 arch/mips/boards/qca-ar9331-generic/board.c
> create mode 100644 arch/mips/boards/qca-ar9331-generic/include/board/board_pbl_start.h
>
> diff --git a/arch/mips/Makefile b/arch/mips/Makefile
> index dd5ceea20..c40ae6604 100644
> --- a/arch/mips/Makefile
> +++ b/arch/mips/Makefile
> @@ -79,6 +79,7 @@ machine-$(CONFIG_MACH_MIPS_AR231X) := ar231x
> board-$(CONFIG_BOARD_NETGEAR_WG102) := netgear-wg102
>
> machine-$(CONFIG_MACH_MIPS_ATH79) := ath79
> +board-$(CONFIG_BOARC_QCA_AR9331_GENERIC) := qca-ar9331-generic
> board-$(CONFIG_BOARD_TPLINK_MR3020) := tplink-mr3020
> board-$(CONFIG_BOARD_TPLINK_WDR4300) := tplink-wdr4300
> board-$(CONFIG_BOARD_BLACK_SWIFT) := black-swift
> diff --git a/arch/mips/boards/qca-ar9331-generic/Makefile b/arch/mips/boards/qca-ar9331-generic/Makefile
> new file mode 100644
> index 000000000..dcfc2937d
> --- /dev/null
> +++ b/arch/mips/boards/qca-ar9331-generic/Makefile
> @@ -0,0 +1 @@
> +obj-y += board.o
> diff --git a/arch/mips/boards/qca-ar9331-generic/board.c b/arch/mips/boards/qca-ar9331-generic/board.c
> new file mode 100644
> index 000000000..7ec7ef8a5
> --- /dev/null
> +++ b/arch/mips/boards/qca-ar9331-generic/board.c
> @@ -0,0 +1,8 @@
> +#include <common.h>
> +#include <init.h>
> +
> +static int dummy_init(void)
> +{
> + return 0;
> +}
> +postcore_initcall(dummy_init);
Why this?
Sascha
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 6+ messages in thread* Re: [PATCH v1 2/4] MIPS: add generic QCA AR9331 board
2017-12-05 8:00 ` Sascha Hauer
@ 2017-12-05 11:43 ` Oleksij Rempel
0 siblings, 0 replies; 6+ messages in thread
From: Oleksij Rempel @ 2017-12-05 11:43 UTC (permalink / raw)
To: Sascha Hauer; +Cc: barebox
[-- Attachment #1.1.1: Type: text/plain, Size: 2216 bytes --]
Am 05.12.2017 um 09:00 schrieb Sascha Hauer:
> On Fri, Dec 01, 2017 at 01:52:49PM +0100, Oleksij Rempel wrote:
>> this board may cover most of existing ar9331 boards
>>
>> Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
>> ---
>> arch/mips/Makefile | 1 +
>> arch/mips/boards/qca-ar9331-generic/Makefile | 1 +
>> arch/mips/boards/qca-ar9331-generic/board.c | 8 ++++
>> .../include/board/board_pbl_start.h | 46 ++++++++++++++++++++++
>> arch/mips/mach-ath79/Kconfig | 7 ++++
>> 5 files changed, 63 insertions(+)
>> create mode 100644 arch/mips/boards/qca-ar9331-generic/Makefile
>> create mode 100644 arch/mips/boards/qca-ar9331-generic/board.c
>> create mode 100644 arch/mips/boards/qca-ar9331-generic/include/board/board_pbl_start.h
>>
>> diff --git a/arch/mips/Makefile b/arch/mips/Makefile
>> index dd5ceea20..c40ae6604 100644
>> --- a/arch/mips/Makefile
>> +++ b/arch/mips/Makefile
>> @@ -79,6 +79,7 @@ machine-$(CONFIG_MACH_MIPS_AR231X) := ar231x
>> board-$(CONFIG_BOARD_NETGEAR_WG102) := netgear-wg102
>>
>> machine-$(CONFIG_MACH_MIPS_ATH79) := ath79
>> +board-$(CONFIG_BOARC_QCA_AR9331_GENERIC) := qca-ar9331-generic
>> board-$(CONFIG_BOARD_TPLINK_MR3020) := tplink-mr3020
>> board-$(CONFIG_BOARD_TPLINK_WDR4300) := tplink-wdr4300
>> board-$(CONFIG_BOARD_BLACK_SWIFT) := black-swift
>> diff --git a/arch/mips/boards/qca-ar9331-generic/Makefile b/arch/mips/boards/qca-ar9331-generic/Makefile
>> new file mode 100644
>> index 000000000..dcfc2937d
>> --- /dev/null
>> +++ b/arch/mips/boards/qca-ar9331-generic/Makefile
>> @@ -0,0 +1 @@
>> +obj-y += board.o
>> diff --git a/arch/mips/boards/qca-ar9331-generic/board.c b/arch/mips/boards/qca-ar9331-generic/board.c
>> new file mode 100644
>> index 000000000..7ec7ef8a5
>> --- /dev/null
>> +++ b/arch/mips/boards/qca-ar9331-generic/board.c
>> @@ -0,0 +1,8 @@
>> +#include <common.h>
>> +#include <init.h>
>> +
>> +static int dummy_init(void)
>> +{
>> + return 0;
>> +}
>> +postcore_initcall(dummy_init);
>
> Why this?
After some discussion we decided to drop this patchset.
--
Regards,
Oleksij
[-- Attachment #1.2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
[-- Attachment #2: Type: text/plain, Size: 149 bytes --]
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v1 3/4] MIPS: add support for DPTechnics DPT-Module v1
2017-12-01 12:52 [PATCH v1 1/4] MIPS: ath79: ar9331: add generic RAM macro Oleksij Rempel
2017-12-01 12:52 ` [PATCH v1 2/4] MIPS: add generic QCA AR9331 board Oleksij Rempel
@ 2017-12-01 12:52 ` Oleksij Rempel
2017-12-01 12:52 ` [PATCH v1 4/4] MIPS: ar9331: add watchdog support Oleksij Rempel
2 siblings, 0 replies; 6+ messages in thread
From: Oleksij Rempel @ 2017-12-01 12:52 UTC (permalink / raw)
To: barebox; +Cc: Oleksij Rempel
This product can be found here:
https://dptechnics.com/en/products/dpt-module-v1.html
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
---
arch/mips/configs/dptechnics-dpt-module_defconfig | 89 +++++++++++++++++++++++
arch/mips/dts/ar9331-dptechnics-dpt-module.dts | 31 ++++++++
2 files changed, 120 insertions(+)
create mode 100644 arch/mips/configs/dptechnics-dpt-module_defconfig
create mode 100644 arch/mips/dts/ar9331-dptechnics-dpt-module.dts
diff --git a/arch/mips/configs/dptechnics-dpt-module_defconfig b/arch/mips/configs/dptechnics-dpt-module_defconfig
new file mode 100644
index 000000000..dbad08fe6
--- /dev/null
+++ b/arch/mips/configs/dptechnics-dpt-module_defconfig
@@ -0,0 +1,89 @@
+CONFIG_BUILTIN_DTB=y
+CONFIG_BUILTIN_DTB_NAME="ar9331-dptechnics-dpt-module"
+CONFIG_MACH_MIPS_ATH79=y
+CONFIG_BOARC_QCA_AR9331_GENERIC=y
+CONFIG_PBL_IMAGE=y
+CONFIG_IMAGE_COMPRESSION_XZKERN=y
+CONFIG_MMU=y
+CONFIG_TEXT_BASE=0x82000000
+CONFIG_MALLOC_TLSF=y
+CONFIG_HUSH_FANCY_PROMPT=y
+CONFIG_CMDLINE_EDITING=y
+CONFIG_AUTO_COMPLETE=y
+CONFIG_CONSOLE_RATP=y
+CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW=y
+CONFIG_RESET_SOURCE=y
+CONFIG_CMD_DMESG=y
+CONFIG_LONGHELP=y
+CONFIG_CMD_IOMEM=y
+CONFIG_CMD_IMD=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_GO=y
+CONFIG_CMD_LOADB=y
+CONFIG_CMD_LOADY=y
+CONFIG_CMD_RESET=y
+CONFIG_CMD_EXPORT=y
+CONFIG_CMD_DEFAULTENV=y
+CONFIG_CMD_LOADENV=y
+CONFIG_CMD_MAGICVAR=y
+CONFIG_CMD_MAGICVAR_HELP=y
+CONFIG_CMD_SAVEENV=y
+CONFIG_CMD_SHA1SUM=y
+CONFIG_CMD_UNCOMPRESS=y
+CONFIG_CMD_LET=y
+CONFIG_CMD_MSLEEP=y
+CONFIG_CMD_READF=y
+CONFIG_CMD_SLEEP=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_HOST=y
+CONFIG_CMD_MIITOOL=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_ECHO_E=y
+CONFIG_CMD_EDIT=y
+CONFIG_CMD_READLINE=y
+CONFIG_CMD_TIMEOUT=y
+CONFIG_CMD_CRC=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_MM=y
+CONFIG_CMD_CLK=y
+CONFIG_CMD_DETECT=y
+CONFIG_CMD_FLASH=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_LED=y
+CONFIG_CMD_POWEROFF=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_LED_TRIGGER=y
+CONFIG_CMD_WD=y
+CONFIG_CMD_BAREBOX_UPDATE=y
+CONFIG_CMD_OF_NODE=y
+CONFIG_CMD_OF_PROPERTY=y
+CONFIG_CMD_OFTREE=y
+CONFIG_CMD_TIME=y
+CONFIG_NET=y
+CONFIG_NET_NFS=y
+CONFIG_NET_NETCONSOLE=y
+CONFIG_NET_SNTP=y
+CONFIG_OFDEVICE=y
+CONFIG_OF_BAREBOX_DRIVERS=y
+CONFIG_OF_BAREBOX_ENV_IN_FS=y
+CONFIG_DRIVER_SERIAL_AR933X=y
+CONFIG_DRIVER_NET_AG71XX=y
+CONFIG_AR8327N_PHY=y
+CONFIG_AT803X_PHY=y
+CONFIG_MDIO_BITBANG=y
+CONFIG_MDIO_GPIO=y
+CONFIG_DRIVER_SPI_ATH79=y
+CONFIG_MTD=y
+# CONFIG_MTD_OOB_DEVICE is not set
+CONFIG_MTD_M25P80=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_LED_GPIO_OF=y
+CONFIG_LED_TRIGGERS=y
+CONFIG_WATCHDOG=y
+CONFIG_WATCHDOG_AR9344=y
+CONFIG_FS_TFTP=y
+CONFIG_FS_NFS=y
+CONFIG_FS_RATP=y
+CONFIG_DIGEST_SHA224_GENERIC=y
+CONFIG_DIGEST_SHA256_GENERIC=y
diff --git a/arch/mips/dts/ar9331-dptechnics-dpt-module.dts b/arch/mips/dts/ar9331-dptechnics-dpt-module.dts
new file mode 100644
index 000000000..39eb36600
--- /dev/null
+++ b/arch/mips/dts/ar9331-dptechnics-dpt-module.dts
@@ -0,0 +1,31 @@
+#include <mips/qca/ar9331_dpt_module.dts>
+#include "ar9331.dtsi"
+
+/ {
+ aliases {
+ spiflash = &spiflash;
+ };
+
+ chosen {
+ environment@0 {
+ compatible = "barebox,environment";
+ device-path = &spiflash, "partname:barebox-environment";
+ };
+ };
+};
+
+&spiflash {
+ partition@0 {
+ label = "barebox";
+ reg = <0 0x80000>;
+ };
+
+ partition@80000 {
+ label = "barebox-environment";
+ reg = <0x80000 0x10000>;
+ };
+};
+
+&mac0 {
+ status = "okay";
+};
--
2.14.1
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 6+ messages in thread* [PATCH v1 4/4] MIPS: ar9331: add watchdog support
2017-12-01 12:52 [PATCH v1 1/4] MIPS: ath79: ar9331: add generic RAM macro Oleksij Rempel
2017-12-01 12:52 ` [PATCH v1 2/4] MIPS: add generic QCA AR9331 board Oleksij Rempel
2017-12-01 12:52 ` [PATCH v1 3/4] MIPS: add support for DPTechnics DPT-Module v1 Oleksij Rempel
@ 2017-12-01 12:52 ` Oleksij Rempel
2 siblings, 0 replies; 6+ messages in thread
From: Oleksij Rempel @ 2017-12-01 12:52 UTC (permalink / raw)
To: barebox; +Cc: Oleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
---
arch/mips/dts/ar9331.dtsi | 6 ++++++
drivers/watchdog/Kconfig | 2 +-
2 files changed, 7 insertions(+), 1 deletion(-)
diff --git a/arch/mips/dts/ar9331.dtsi b/arch/mips/dts/ar9331.dtsi
index b4b8b766b..42baae1e8 100644
--- a/arch/mips/dts/ar9331.dtsi
+++ b/arch/mips/dts/ar9331.dtsi
@@ -1,5 +1,11 @@
/ {
ahb {
+ wdt0: wdt@18060008 {
+ compatible = "qca,ar9331-wdt", "qca,ar9344-wdt";
+ reg = <0x18060008 0x8>;
+ clocks = <&pll ATH79_CLK_CPU>;
+ };
+
mac0: mac@19000000 {
compatible = "qca,ar9331-ge0";
reg = <0x18070000 0x00000100>,
diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
index 1f04c7fba..a8f9492ac 100644
--- a/drivers/watchdog/Kconfig
+++ b/drivers/watchdog/Kconfig
@@ -12,7 +12,7 @@ if WATCHDOG
config WATCHDOG_AR9344
bool "QCA AR9344"
- depends on SOC_QCA_AR9344
+ depends on SOC_QCA_AR9344 || SOC_QCA_AR9331
help
Add support for watchdog on the QCA AR9344 SoC.
--
2.14.1
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2017-12-05 11:43 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-12-01 12:52 [PATCH v1 1/4] MIPS: ath79: ar9331: add generic RAM macro Oleksij Rempel
2017-12-01 12:52 ` [PATCH v1 2/4] MIPS: add generic QCA AR9331 board Oleksij Rempel
2017-12-05 8:00 ` Sascha Hauer
2017-12-05 11:43 ` Oleksij Rempel
2017-12-01 12:52 ` [PATCH v1 3/4] MIPS: add support for DPTechnics DPT-Module v1 Oleksij Rempel
2017-12-01 12:52 ` [PATCH v1 4/4] MIPS: ar9331: add watchdog support Oleksij Rempel
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox