From: Andrey Smirnov <andrew.smirnov@gmail.com>
To: barebox@lists.infradead.org
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Subject: [PATCH v2 1/6] ARM: vybrid: zii: Make use of DT code from Linux kernel
Date: Mon, 4 Dec 2017 07:27:13 -0800 [thread overview]
Message-ID: <20171204152718.10674-2-andrew.smirnov@gmail.com> (raw)
In-Reply-To: <20171204152718.10674-1-andrew.smirnov@gmail.com>
Now that vf610-zii-dev.dts, vf610-zii-dev-rev-b.dts and
vf610-zii-dev-rev-c.dts made their way from Linux to Barebox, convert
all relevant code to make use of them.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
---
arch/arm/dts/vf610-zii-cfu1-rev-a.dts | 3 +-
arch/arm/dts/vf610-zii-dev-rev-b.dts | 386 +----------------------------
arch/arm/dts/vf610-zii-dev-rev-c.dts | 391 +-----------------------------
arch/arm/dts/vf610-zii-dev.dtsi | 354 ---------------------------
arch/arm/dts/vf610-zii-scu4-aib-rev-c.dts | 2 +
arch/arm/dts/vf610-zii-spu3-rev-a.dts | 4 +-
6 files changed, 9 insertions(+), 1131 deletions(-)
diff --git a/arch/arm/dts/vf610-zii-cfu1-rev-a.dts b/arch/arm/dts/vf610-zii-cfu1-rev-a.dts
index 4147d138b..7e87a15c1 100644
--- a/arch/arm/dts/vf610-zii-cfu1-rev-a.dts
+++ b/arch/arm/dts/vf610-zii-cfu1-rev-a.dts
@@ -42,9 +42,10 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
+/dts-v1/;
+#include <arm/vf610-zii-dev.dtsi>
-/dts-v1/;
#include "vf610-zii-dev.dtsi"
/ {
diff --git a/arch/arm/dts/vf610-zii-dev-rev-b.dts b/arch/arm/dts/vf610-zii-dev-rev-b.dts
index bf0a01021..1eb01f44a 100644
--- a/arch/arm/dts/vf610-zii-dev-rev-b.dts
+++ b/arch/arm/dts/vf610-zii-dev-rev-b.dts
@@ -42,390 +42,6 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-/dts-v1/;
+#include <arm/vf610-zii-dev-rev-b.dts>
#include "vf610-zii-dev.dtsi"
-
-/*
- * =============================================================
- * The following code is shared with Linux kernel and should be
- * removed once it trickles down from there eventually
- * =============================================================
- */
-
-/ {
- model = "ZII VF610 Development Board, Rev B";
- compatible = "zii,vf610dev-b", "zii,vf610dev", "fsl,vf610";
-
- mdio-mux {
- compatible = "mdio-mux-gpio";
- pinctrl-0 = <&pinctrl_mdio_mux>;
- pinctrl-names = "default";
- gpios = <&gpio0 8 GPIO_ACTIVE_HIGH
- &gpio0 9 GPIO_ACTIVE_HIGH
- &gpio0 24 GPIO_ACTIVE_HIGH
- &gpio0 25 GPIO_ACTIVE_HIGH>;
- mdio-parent-bus = <&mdio1>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- mdio_mux_1: mdio@1 {
- reg = <1>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- switch0: switch0@0 {
- compatible = "marvell,mv88e6085";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
- dsa,member = <0 0>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
- port@0 {
- reg = <0>;
- label = "lan0";
- };
-
- port@1 {
- reg = <1>;
- label = "lan1";
- };
-
- port@2 {
- reg = <2>;
- label = "lan2";
- };
-
- switch0port5: port@5 {
- reg = <5>;
- label = "dsa";
- phy-mode = "rgmii-txid";
- link = <&switch1port6
- &switch2port9>;
- };
-
- port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <&fec1>;
- fixed-link {
- speed = <100>;
- full-duplex;
- };
- };
- };
- };
- };
-
- mdio_mux_2: mdio@2 {
- reg = <2>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- switch1: switch1@0 {
- compatible = "marvell,mv88e6085";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
- dsa,member = <0 1>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
- port@0 {
- reg = <0>;
- label = "lan3";
- phy-handle = <&switch1phy0>;
- };
-
- port@1 {
- reg = <1>;
- label = "lan4";
- phy-handle = <&switch1phy1>;
- };
-
- port@2 {
- reg = <2>;
- label = "lan5";
- phy-handle = <&switch1phy2>;
- };
-
- switch1port5: port@5 {
- reg = <5>;
- label = "dsa";
- link = <&switch2port9>;
- phy-mode = "rgmii-txid";
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- switch1port6: port@6 {
- reg = <6>;
- label = "dsa";
- phy-mode = "rgmii-txid";
- link = <&switch0port5>;
- };
- };
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- switch1phy0: switch1phy0@0 {
- reg = <0>;
- };
- switch1phy1: switch1phy0@1 {
- reg = <1>;
- };
- switch1phy2: switch1phy0@2 {
- reg = <2>;
- };
- };
- };
- };
-
- mdio_mux_4: mdio@4 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <4>;
-
- switch2: switch2@0 {
- compatible = "marvell,mv88e6085";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
- dsa,member = <0 2>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
- port@0 {
- reg = <0>;
- label = "lan6";
- };
-
- port@1 {
- reg = <1>;
- label = "lan7";
- };
-
- port@2 {
- reg = <2>;
- label = "lan8";
- };
-
- port@3 {
- reg = <3>;
- label = "optical3";
- fixed-link {
- speed = <1000>;
- full-duplex;
- link-gpios = <&gpio6 2
- GPIO_ACTIVE_HIGH>;
- };
- };
-
- port@4 {
- reg = <4>;
- label = "optical4";
- fixed-link {
- speed = <1000>;
- full-duplex;
- link-gpios = <&gpio6 3
- GPIO_ACTIVE_HIGH>;
- };
- };
-
- switch2port9: port@9 {
- reg = <9>;
- label = "dsa";
- phy-mode = "rgmii-txid";
- link = <&switch1port5
- &switch0port5>;
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
- };
- };
-
- mdio_mux_8: mdio@8 {
- reg = <8>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
- };
-
- spi0 {
- compatible = "spi-gpio";
- pinctrl-0 = <&pinctrl_gpio_spi0>;
- pinctrl-names = "default";
- #address-cells = <1>;
- #size-cells = <0>;
- gpio-sck = <&gpio1 12 GPIO_ACTIVE_HIGH>;
- gpio-mosi = <&gpio1 11 GPIO_ACTIVE_HIGH>;
- gpio-miso = <&gpio1 10 GPIO_ACTIVE_HIGH>;
- cs-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH
- &gpio1 8 GPIO_ACTIVE_HIGH>;
- num-chipselects = <2>;
-
- m25p128@0 {
- compatible = "m25p128", "jedec,spi-nor";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0>;
- spi-max-frequency = <1000000>;
- };
-
- at93c46d@1 {
- compatible = "atmel,at93c46d";
- pinctrl-0 = <&pinctrl_gpio_e6185_eeprom_sel>;
- pinctrl-names = "default";
- #address-cells = <0>;
- #size-cells = <0>;
- reg = <1>;
- spi-max-frequency = <500000>;
- spi-cs-high;
- data-size = <16>;
- select-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&i2c0 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c0>;
- status = "okay";
-
- gpio5: pca9554@20 {
- compatible = "nxp,pca9554";
- reg = <0x20>;
- gpio-controller;
- #gpio-cells = <2>;
-
- };
-
- gpio6: pca9554@22 {
- compatible = "nxp,pca9554";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pca9554_22>;
- reg = <0x22>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-parent = <&gpio2>;
- interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
- };
-};
-
-&i2c2 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c2>;
- status = "okay";
-
- tca9548@70 {
- compatible = "nxp,pca9548";
- pinctrl-0 = <&pinctrl_i2c_mux_reset>;
- pinctrl-names = "default";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x70>;
- reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
-
- i2c@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
-
- sfp1: at24c04@50 {
- compatible = "atmel,24c02";
- reg = <0x50>;
- };
- };
-
- i2c@1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
-
- sfp2: at24c04@50 {
- compatible = "atmel,24c02";
- reg = <0x50>;
- };
- };
-
- i2c@2 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <2>;
-
- sfp3: at24c04@50 {
- compatible = "atmel,24c02";
- reg = <0x50>;
- };
- };
-
- i2c@3 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <3>;
-
- sfp4: at24c04@50 {
- compatible = "atmel,24c02";
- reg = <0x50>;
- };
- };
-
- i2c@4 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <4>;
- };
- };
-};
-
-
-&iomuxc {
- pinctrl_gpio_e6185_eeprom_sel: pinctrl-gpio-e6185-eeprom-spi0 {
- fsl,pins = <
- VF610_PAD_PTE27__GPIO_132 0x33e2
- >;
- };
-
- pinctrl_gpio_spi0: pinctrl-gpio-spi0 {
- fsl,pins = <
- VF610_PAD_PTB22__GPIO_44 0x33e2
- VF610_PAD_PTB21__GPIO_43 0x33e2
- VF610_PAD_PTB20__GPIO_42 0x33e1
- VF610_PAD_PTB19__GPIO_41 0x33e2
- VF610_PAD_PTB18__GPIO_40 0x33e2
- >;
- };
-
- pinctrl_mdio_mux: pinctrl-mdio-mux {
- fsl,pins = <
- VF610_PAD_PTA18__GPIO_8 0x31c2
- VF610_PAD_PTA19__GPIO_9 0x31c2
- VF610_PAD_PTB2__GPIO_24 0x31c2
- VF610_PAD_PTB3__GPIO_25 0x31c2
- >;
- };
-
- pinctrl_pca9554_22: pinctrl-pca95540-22 {
- fsl,pins = <
- VF610_PAD_PTB28__GPIO_98 0x219d
- >;
- };
-};
-
-/*
- * =============================================================
- * End of shared part
- * =============================================================
-*/
diff --git a/arch/arm/dts/vf610-zii-dev-rev-c.dts b/arch/arm/dts/vf610-zii-dev-rev-c.dts
index 522894263..797b31bef 100644
--- a/arch/arm/dts/vf610-zii-dev-rev-c.dts
+++ b/arch/arm/dts/vf610-zii-dev-rev-c.dts
@@ -42,399 +42,10 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-/dts-v1/;
+#include <arm/vf610-zii-dev-rev-c.dts>
#include "vf610-zii-dev.dtsi"
-/*
- * =============================================================
- * The following code is shared with Linux kernel and should be
- * removed once it trickles down from there eventually
- * =============================================================
- */
-
-/ {
- model = "ZII VF610 Development Board, Rev C";
- compatible = "zii,vf610dev-c", "zii,vf610dev", "fsl,vf610";
-
- mdio-mux {
- compatible = "mdio-mux-gpio";
- pinctrl-0 = <&pinctrl_mdio_mux>;
- pinctrl-names = "default";
- gpios = <&gpio0 8 GPIO_ACTIVE_HIGH
- &gpio0 9 GPIO_ACTIVE_HIGH
- &gpio0 25 GPIO_ACTIVE_HIGH>;
- mdio-parent-bus = <&mdio1>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- mdio_mux_1: mdio@1 {
- reg = <1>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- switch0: switch0@0 {
- compatible = "marvell,mv88e6190";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
- dsa,member = <0 0>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "cpu";
- ethernet = <&fec1>;
- fixed-link {
- speed = <100>;
- full-duplex;
- };
- };
-
- port@1 {
- reg = <1>;
- label = "lan1";
- };
-
- port@2 {
- reg = <2>;
- label = "lan2";
- };
-
- port@3 {
- reg = <3>;
- label = "lan3";
- };
-
- port@4 {
- reg = <4>;
- label = "lan4";
- };
-
- switch0port10: port@10 {
- reg = <10>;
- label = "dsa";
- phy-mode = "xgmii";
- link = <&switch1port10>;
- };
- };
- };
- };
-
- mdio_mux_2: mdio@2 {
- reg = <2>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- switch1: switch1@0 {
- compatible = "marvell,mv88e6190";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
- dsa,member = <0 1>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@1 {
- reg = <1>;
- label = "lan5";
- };
-
- port@2 {
- reg = <2>;
- label = "lan6";
- };
-
- port@3 {
- reg = <3>;
- label = "lan7";
- };
-
- port@4 {
- reg = <4>;
- label = "lan8";
- };
-
-
- switch1port10: port@10 {
- reg = <10>;
- label = "dsa";
- phy-mode = "xgmii";
- link = <&switch0port10>;
- };
- };
- };
- };
-
- mdio_mux_4: mdio@4 {
- reg = <4>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
- };
-};
-
-&dspi0 {
- bus-num = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_dspi0>;
- status = "okay";
- spi-num-chipselects = <2>;
-
- m25p128@0 {
- compatible = "m25p128", "jedec,spi-nor";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0>;
- spi-max-frequency = <50000000>;
- };
-
- atzb-rf-233@1 {
- compatible = "atmel,at86rf233";
-
- pinctrl-names = "default";
- pinctrl-0 = <&pinctr_atzb_rf_233>;
-
- spi-max-frequency = <7500000>;
- reg = <1>;
- interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-parent = <&gpio3>;
- xtal-trim = /bits/ 8 <0x06>;
-
- sleep-gpio = <&gpio0 24 GPIO_ACTIVE_HIGH>;
- reset-gpio = <&gpio6 10 GPIO_ACTIVE_HIGH>;
-
- fsl,spi-cs-sck-delay = <180>;
- fsl,spi-sck-cs-delay = <250>;
- };
-};
-
-&dspi2 {
- bus-num = <2>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_dspi2>;
- status = "okay";
- spi-num-chipselects = <2>;
-};
-
-&i2c0 {
- /*
- * U712
- *
- * Exposed signals:
- * P1 - WE2_CMD
- * P2 - WE2_CLK
- */
- gpio5: pca9557@18 {
- compatible = "nxp,pca9557";
- reg = <0x18>;
- gpio-controller;
- #gpio-cells = <2>;
- };
-
- /*
- * U121
- *
- * Exposed signals:
- * I/O0 - ENET_SWR_EN
- * I/O1 - ESW1_RESETn
- * I/O2 - ARINC_RESET
- * I/O3 - DD1_IO_RESET
- * I/O4 - ESW2_RESETn
- * I/O5 - ESW3_RESETn
- * I/O6 - ESW4_RESETn
- * I/O8 - TP909
- * I/O9 - FEM_SEL
- * I/O10 - WIFI_RESETn
- * I/O11 - PHY_RSTn
- * I/O12 - OPT1_SD
- * I/O13 - OPT2_SD
- * I/O14 - OPT1_TX_DIS
- * I/O15 - OPT2_TX_DIS
- */
- gpio6: sx1503@20 {
- compatible = "semtech,sx1503q";
-
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_sx1503_20>;
- #gpio-cells = <2>;
- #interrupt-cells = <2>;
- reg = <0x20>;
- interrupt-parent = <&gpio0>;
- interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
- gpio-controller;
- interrupt-controller;
-
- enet_swr_en {
- gpio-hog;
- gpios = <0 GPIO_ACTIVE_HIGH>;
- output-high;
- line-name = "enet-swr-en";
- };
- };
-
- /*
- * U715
- *
- * Exposed signals:
- * IO0 - WE1_CLK
- * IO1 - WE1_CMD
- */
- gpio7: pca9554@22 {
- compatible = "nxp,pca9554";
- reg = <0x22>;
- gpio-controller;
- #gpio-cells = <2>;
-
- };
-};
-
-&i2c1 {
- at24mac602@00 {
- compatible = "atmel,24c02";
- reg = <0x50>;
- read-only;
- };
-};
-
-&i2c2 {
- tca9548@70 {
- compatible = "nxp,pca9548";
- pinctrl-0 = <&pinctrl_i2c_mux_reset>;
- pinctrl-names = "default";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x70>;
- reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
-
- i2c@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
- };
-
- i2c@1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
-
- sfp2: at24c04@50 {
- compatible = "atmel,24c02";
- reg = <0x50>;
- };
- };
-
- i2c@2 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <2>;
-
- sfp3: at24c04@50 {
- compatible = "atmel,24c02";
- reg = <0x50>;
- };
- };
-
- i2c@3 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <3>;
- };
- };
-};
-
-&uart3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart3>;
- status = "okay";
-};
-
-&gpio0 {
- eth0_intrp {
- gpio-hog;
- gpios = <23 GPIO_ACTIVE_HIGH>;
- input;
- line-name = "sx1503-irq";
- };
-};
-
-&gpio3 {
- eth0_intrp {
- gpio-hog;
- gpios = <2 GPIO_ACTIVE_HIGH>;
- input;
- line-name = "eth0-intrp";
- };
-};
-
-&fec0 {
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- status = "okay";
-
- ethernet-phy@0 {
- compatible = "ethernet-phy-ieee802.3-c22";
-
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_fec0_phy_int>;
-
- interrupt-parent = <&gpio3>;
- interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
- reg = <0>;
- };
- };
-};
-
-&iomuxc {
- pinctr_atzb_rf_233: pinctrl-atzb-rf-233 {
- fsl,pins = <
- VF610_PAD_PTB2__GPIO_24 0x31c2
- VF610_PAD_PTE27__GPIO_132 0x33e2
- >;
- };
-
-
- pinctrl_sx1503_20: pinctrl-sx1503-20 {
- fsl,pins = <
- VF610_PAD_PTB1__GPIO_23 0x219d
- >;
- };
-
- pinctrl_uart3: uart3grp {
- fsl,pins = <
- VF610_PAD_PTA20__UART3_TX 0x21a2
- VF610_PAD_PTA21__UART3_RX 0x21a1
- >;
- };
-
- pinctrl_mdio_mux: pinctrl-mdio-mux {
- fsl,pins = <
- VF610_PAD_PTA18__GPIO_8 0x31c2
- VF610_PAD_PTA19__GPIO_9 0x31c2
- VF610_PAD_PTB3__GPIO_25 0x31c2
- >;
- };
-
- pinctrl_fec0_phy_int: pinctrl-fec0-phy-int {
- fsl,pins = <
- VF610_PAD_PTB28__GPIO_98 0x219d
- >;
- };
-};
-
-/*
- * =============================================================
- * End of shared part
- * =============================================================
- */
-
-
&dspi0 {
m25p128@0 {
partition@0 {
diff --git a/arch/arm/dts/vf610-zii-dev.dtsi b/arch/arm/dts/vf610-zii-dev.dtsi
index dae077ced..4bf81451a 100644
--- a/arch/arm/dts/vf610-zii-dev.dtsi
+++ b/arch/arm/dts/vf610-zii-dev.dtsi
@@ -42,360 +42,6 @@ n * copy, modify, merge, publish, distribute, sublicense, and/or
* OTHER DEALINGS IN THE SOFTWARE.
*/
-
-/*
- * =============================================================
- * The following code is shared with Linux kernel and should be
- * removed once it trickles down from there eventually
- * =============================================================
- */
-
-#include <arm/vf610.dtsi>
-
-/ {
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- memory {
- reg = <0x80000000 0x20000000>;
- };
-
- gpio-leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&pinctrl_leds_debug>;
- pinctrl-names = "default";
-
- debug {
- label = "zii:green:debug1";
- gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- };
- };
-
- reg_vcc_3v3_mcu: regulator-vcc-3v3-mcu {
- compatible = "regulator-fixed";
- regulator-name = "vcc_3v3_mcu";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- usb0_vbus: regulator-usb0-vbus {
- compatible = "regulator-fixed";
- pinctrl-0 = <&pinctrl_usb_vbus>;
- regulator-name = "usb_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- enable-active-high;
- regulator-always-on;
- regulator-boot-on;
- gpio = <&gpio0 6 0>;
- };
-};
-
-&adc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_adc0_ad5>;
- vref-supply = <®_vcc_3v3_mcu>;
- status = "okay";
-};
-
-&edma0 {
- status = "okay";
-};
-
-&esdhc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_esdhc1>;
- bus-width = <4>;
- status = "okay";
-};
-
-&fec0 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_fec0>;
- status = "okay";
-};
-
-&fec1 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_fec1>;
- status = "okay";
-
- fixed-link {
- speed = <100>;
- full-duplex;
- };
-
- mdio1: mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- status = "okay";
- };
-};
-
-&i2c0 {
- clock-frequency = <100000>;
- pinctrl-names = "default", "gpio";
- pinctrl-0 = <&pinctrl_i2c0>;
- pinctrl-1 = <&pinctrl_i2c0_gpio>;
- scl-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
- sda-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
- status = "okay";
-
- lm75@48 {
- compatible = "national,lm75";
- reg = <0x48>;
- };
-
- at24c04@50 {
- compatible = "atmel,24c04";
- reg = <0x50>;
- };
-
- at24c04@52 {
- compatible = "atmel,24c04";
- reg = <0x52>;
- };
-
- ds1682@6b {
- compatible = "dallas,ds1682";
- reg = <0x6b>;
- };
-};
-
-&i2c1 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c1>;
- status = "okay";
-};
-
-&i2c2 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c2>;
- status = "okay";
-};
-
-&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart0>;
- status = "okay";
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
- status = "okay";
-};
-
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
- status = "okay";
-};
-
-&usbdev0 {
- disable-over-current;
- vbus-supply = <&usb0_vbus>;
- dr_mode = "host";
- status = "okay";
-};
-
-&usbh1 {
- disable-over-current;
- status = "okay";
-};
-
-&usbmisc0 {
- status = "okay";
-};
-
-&usbmisc1 {
- status = "okay";
-};
-
-&usbphy0 {
- status = "okay";
-};
-
-&usbphy1 {
- status = "okay";
-};
-
-&iomuxc {
- pinctrl_adc0_ad5: adc0ad5grp {
- fsl,pins = <
- VF610_PAD_PTC30__ADC0_SE5 0x00a1
- >;
- };
-
- pinctrl_dspi0: dspi0grp {
- fsl,pins = <
- VF610_PAD_PTB18__DSPI0_CS1 0x1182
- VF610_PAD_PTB19__DSPI0_CS0 0x1182
- VF610_PAD_PTB20__DSPI0_SIN 0x1181
- VF610_PAD_PTB21__DSPI0_SOUT 0x1182
- VF610_PAD_PTB22__DSPI0_SCK 0x1182
- >;
- };
-
- pinctrl_dspi2: dspi2grp {
- fsl,pins = <
- VF610_PAD_PTD31__DSPI2_CS1 0x1182
- VF610_PAD_PTD30__DSPI2_CS0 0x1182
- VF610_PAD_PTD29__DSPI2_SIN 0x1181
- VF610_PAD_PTD28__DSPI2_SOUT 0x1182
- VF610_PAD_PTD27__DSPI2_SCK 0x1182
- >;
- };
-
- pinctrl_esdhc1: esdhc1grp {
- fsl,pins = <
- VF610_PAD_PTA24__ESDHC1_CLK 0x31ef
- VF610_PAD_PTA25__ESDHC1_CMD 0x31ef
- VF610_PAD_PTA26__ESDHC1_DAT0 0x31ef
- VF610_PAD_PTA27__ESDHC1_DAT1 0x31ef
- VF610_PAD_PTA28__ESDHC1_DATA2 0x31ef
- VF610_PAD_PTA29__ESDHC1_DAT3 0x31ef
- VF610_PAD_PTA7__GPIO_134 0x219d
- >;
- };
-
- pinctrl_fec0: fec0grp {
- fsl,pins = <
- VF610_PAD_PTC0__ENET_RMII0_MDC 0x30d2
- VF610_PAD_PTC1__ENET_RMII0_MDIO 0x30d3
- VF610_PAD_PTC2__ENET_RMII0_CRS 0x30d1
- VF610_PAD_PTC3__ENET_RMII0_RXD1 0x30d1
- VF610_PAD_PTC4__ENET_RMII0_RXD0 0x30d1
- VF610_PAD_PTC5__ENET_RMII0_RXER 0x30d1
- VF610_PAD_PTC6__ENET_RMII0_TXD1 0x30d2
- VF610_PAD_PTC7__ENET_RMII0_TXD0 0x30d2
- VF610_PAD_PTC8__ENET_RMII0_TXEN 0x30d2
- >;
- };
-
- pinctrl_fec1: fec1grp {
- fsl,pins = <
- VF610_PAD_PTA6__RMII_CLKIN 0x30d1
- VF610_PAD_PTC9__ENET_RMII1_MDC 0x30d2
- VF610_PAD_PTC10__ENET_RMII1_MDIO 0x30d3
- VF610_PAD_PTC11__ENET_RMII1_CRS 0x30d1
- VF610_PAD_PTC12__ENET_RMII1_RXD1 0x30d1
- VF610_PAD_PTC13__ENET_RMII1_RXD0 0x30d1
- VF610_PAD_PTC14__ENET_RMII1_RXER 0x30d1
- VF610_PAD_PTC15__ENET_RMII1_TXD1 0x30d2
- VF610_PAD_PTC16__ENET_RMII1_TXD0 0x30d2
- VF610_PAD_PTC17__ENET_RMII1_TXEN 0x30d2
- >;
- };
-
- pinctrl_gpio_spi0: pinctrl-gpio-spi0 {
- fsl,pins = <
- VF610_PAD_PTB22__GPIO_44 0x33e2
- VF610_PAD_PTB21__GPIO_43 0x33e2
- VF610_PAD_PTB20__GPIO_42 0x33e1
- VF610_PAD_PTB19__GPIO_41 0x33e2
- VF610_PAD_PTB18__GPIO_40 0x33e2
- >;
- };
-
- pinctrl_i2c_mux_reset: pinctrl-i2c-mux-reset {
- fsl,pins = <
- VF610_PAD_PTE14__GPIO_119 0x31c2
- >;
- };
-
- pinctrl_i2c0: i2c0grp {
- fsl,pins = <
- VF610_PAD_PTB14__I2C0_SCL 0x37ff
- VF610_PAD_PTB15__I2C0_SDA 0x37ff
- >;
- };
-
- pinctrl_i2c0_gpio: i2c0grp-gpio {
- fsl,pins = <
- VF610_PAD_PTB14__GPIO_36 0x31c2
- VF610_PAD_PTB15__GPIO_37 0x31c2
- >;
- };
-
-
- pinctrl_i2c1: i2c1grp {
- fsl,pins = <
- VF610_PAD_PTB16__I2C1_SCL 0x37ff
- VF610_PAD_PTB17__I2C1_SDA 0x37ff
- >;
- };
-
- pinctrl_i2c2: i2c2grp {
- fsl,pins = <
- VF610_PAD_PTA22__I2C2_SCL 0x37ff
- VF610_PAD_PTA23__I2C2_SDA 0x37ff
- >;
- };
-
- pinctrl_leds_debug: pinctrl-leds-debug {
- fsl,pins = <
- VF610_PAD_PTD20__GPIO_74 0x31c2
- >;
- };
-
- pinctrl_qspi0: qspi0grp {
- fsl,pins = <
- VF610_PAD_PTD7__QSPI0_B_QSCK 0x31c3
- VF610_PAD_PTD8__QSPI0_B_CS0 0x31ff
- VF610_PAD_PTD9__QSPI0_B_DATA3 0x31c3
- VF610_PAD_PTD10__QSPI0_B_DATA2 0x31c3
- VF610_PAD_PTD11__QSPI0_B_DATA1 0x31c3
- VF610_PAD_PTD12__QSPI0_B_DATA0 0x31c3
- >;
- };
-
- pinctrl_uart0: uart0grp {
- fsl,pins = <
- VF610_PAD_PTB10__UART0_TX 0x21a2
- VF610_PAD_PTB11__UART0_RX 0x21a1
- >;
- };
-
- pinctrl_uart1: uart1grp {
- fsl,pins = <
- VF610_PAD_PTB23__UART1_TX 0x21a2
- VF610_PAD_PTB24__UART1_RX 0x21a1
- >;
- };
-
- pinctrl_uart2: uart2grp {
- fsl,pins = <
- VF610_PAD_PTD0__UART2_TX 0x21a2
- VF610_PAD_PTD1__UART2_RX 0x21a1
- >;
- };
-
- pinctrl_usb_vbus: pinctrl-usb-vbus {
- fsl,pins = <
- VF610_PAD_PTA16__GPIO_6 0x31c2
- >;
- };
-
- pinctrl_usb0_host: usb0-host-grp {
- fsl,pins = <
- VF610_PAD_PTD6__GPIO_85 0x0062
- >;
- };
-};
-
-/*
- * =============================================================
- * End of shared part
- * =============================================================
- */
-
/ {
audio_ext: mclk_osc {
compatible = "fixed-clock";
diff --git a/arch/arm/dts/vf610-zii-scu4-aib-rev-c.dts b/arch/arm/dts/vf610-zii-scu4-aib-rev-c.dts
index d10f460e3..12c2568bc 100644
--- a/arch/arm/dts/vf610-zii-scu4-aib-rev-c.dts
+++ b/arch/arm/dts/vf610-zii-scu4-aib-rev-c.dts
@@ -44,6 +44,8 @@
/dts-v1/;
+#include <arm/vf610-zii-dev.dtsi>
+
#include "vf610-zii-dev.dtsi"
/ {
diff --git a/arch/arm/dts/vf610-zii-spu3-rev-a.dts b/arch/arm/dts/vf610-zii-spu3-rev-a.dts
index 25ab26ddf..f362e7f0b 100644
--- a/arch/arm/dts/vf610-zii-spu3-rev-a.dts
+++ b/arch/arm/dts/vf610-zii-spu3-rev-a.dts
@@ -43,8 +43,10 @@
*/
/dts-v1/;
-#include "vf610-zii-dev.dtsi"
+#include <arm/vf610-zii-dev.dtsi>
+
+#include "vf610-zii-dev.dtsi"
/ {
model = "ZII VF610 SPU3 Switch Management Board";
--
2.14.3
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
next prev parent reply other threads:[~2017-12-04 15:28 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-12-04 15:27 [PATCH v2 0/6] MDIO bus multiplexer support Andrey Smirnov
2017-12-04 15:27 ` Andrey Smirnov [this message]
2017-12-04 15:27 ` [PATCH v2 2/6] mdio_bus: Port of_mdio_find_bus() from Linux kernel Andrey Smirnov
2017-12-04 15:27 ` [PATCH v2 3/6] net: phy: Port MDIO bus miltiplexer framework " Andrey Smirnov
2017-12-04 15:27 ` [PATCH v2 4/6] net: phy: Port GPIO controlled MDIO multiplexer driver Andrey Smirnov
2017-12-04 15:27 ` [PATCH v2 5/6] net: mdio-mux: Avoid probing multiplexed busses Andrey Smirnov
2017-12-04 15:27 ` [PATCH v2 6/6] zii_vf610_dev_defconfig: Select MDIO bus GPIO multiplexer Andrey Smirnov
2017-12-06 14:49 ` [PATCH v2 0/6] MDIO bus multiplexer support Sascha Hauer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20171204152718.10674-2-andrew.smirnov@gmail.com \
--to=andrew.smirnov@gmail.com \
--cc=barebox@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox