From: Ladislav Michl <ladis@linux-mips.org>
To: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Barebox List <barebox@lists.infradead.org>
Subject: Re: [PATCH 00/23] AM3517 support
Date: Fri, 14 Dec 2018 17:22:49 +0100 [thread overview]
Message-ID: <20181214162249.GA19868@lenoch> (raw)
In-Reply-To: <20181214141730.26181-1-s.hauer@pengutronix.de>
Hello Sascha,
On Fri, Dec 14, 2018 at 03:17:07PM +0100, Sascha Hauer wrote:
> This series adds support for the TI AM3517 SoC along with Wago PFC-200
> board support. Also in this series some TI related driver patches. Most
> notably some significant chages to the GPMC Nand driver which was not
> really working anymore.
>
> Sascha
>
> Heinrich Toews (3):
> net: davinci-emac: fix buggy channel tear down
> net: davinci-emac: switch to device tree support
> ARM: omap: AM3517: Change default clock rate for AM3517
>
> Oleg Karfich (1):
> ARM: omap3: Add support for reset reason detection
>
> Sascha Hauer (19):
> net: davinci-emac: Add timeout to polling loop
> mci: omap: Improve error handling
> mci: omap: use IS_ENABLED() rather than #ifdef
> mtd: nand: omap: Use dev_dbg when a struct device * is available
> mtd: nand: omap: Fix hamming correct return values
> mtd: nand: omap: Disable subpage reads in hardware ecc mode
> mtd: nand: omap: remove unused function argument
> mtd: nand: omap: fix bch8_hw_romcode ecc layout
> mtd: nand: omap: set eccbytes correctly
> mtd: nand: omap: unbreak BCH8 support
may I point there is a MTD update pending on mailing list which,
once applied, would make merging with upstream drivers easier?
Yes, that upstream, which already fixed those bugs...
> ARM: omap: Add missing include
> ARM: omap: dmtimer: Turn into a driver
> ARM: omap: 32ktimer: Turn into a driver
> ARM: omap: Add AM35XX support
> ARM: omap: enable am33xx_uart_soft_reset for AM35xx
> ARM: omap: Add AM3517 specific mux configuration
> ARM: omap: Add emif4 support for AM3517
> ARM: omap: Add board support for WAGO pfc200 platform
> ARM: omap: am33xx_defconfig: Enable more boards and rename
>
> arch/arm/boards/Makefile | 1 +
> arch/arm/boards/wago-pfc-am35xx/Makefile | 6 +
> arch/arm/boards/wago-pfc-am35xx/board-mlo.c | 73 +++
> arch/arm/boards/wago-pfc-am35xx/board.c | 39 ++
> arch/arm/boards/wago-pfc-am35xx/lowlevel.c | 231 +++++++++
> .../arm/configs/am35xx_pfc200_xload_defconfig | 40 ++
> .../{am335x_defconfig => omap_defconfig} | 5 +-
> arch/arm/dts/Makefile | 1 +
> arch/arm/dts/am35xx-pfc-750_820x.dts | 487 ++++++++++++++++++
> arch/arm/dts/am3xxx-pfc-nandparts.dtsi | 63 +++
> arch/arm/mach-omap/Kconfig | 24 +-
> arch/arm/mach-omap/Makefile | 5 +-
> arch/arm/mach-omap/am33xx_generic.c | 32 +-
> arch/arm/mach-omap/am35xx_emif4.c | 85 +++
> arch/arm/mach-omap/am3xxx.c | 32 ++
> .../mach-omap/include/mach/am3xxx-silicon.h | 6 +
> arch/arm/mach-omap/include/mach/emif4.h | 105 ++++
> arch/arm/mach-omap/include/mach/omap3-clock.h | 2 +
> arch/arm/mach-omap/include/mach/omap3-mux.h | 49 +-
> arch/arm/mach-omap/include/mach/sys_info.h | 2 +
> arch/arm/mach-omap/omap3_clock.c | 16 +-
> arch/arm/mach-omap/omap3_generic.c | 58 ++-
> arch/arm/mach-omap/omap4_generic.c | 5 +-
> drivers/clocksource/Kconfig | 6 +
> drivers/clocksource/Makefile | 2 +
> .../clocksource/timer-ti-32k.c | 39 +-
> .../clocksource/timer-ti-dm.c | 47 +-
> drivers/mci/omap_hsmmc.c | 37 +-
> drivers/mtd/nand/nand_omap_gpmc.c | 141 +++--
> drivers/net/davinci_emac.c | 210 +++++---
> images/Makefile | 1 +
> images/Makefile.am35xx | 24 +
> include/platform_data/eth-davinci-emac.h | 10 -
> 33 files changed, 1657 insertions(+), 227 deletions(-)
> create mode 100644 arch/arm/boards/wago-pfc-am35xx/Makefile
> create mode 100644 arch/arm/boards/wago-pfc-am35xx/board-mlo.c
> create mode 100644 arch/arm/boards/wago-pfc-am35xx/board.c
> create mode 100644 arch/arm/boards/wago-pfc-am35xx/lowlevel.c
> create mode 100644 arch/arm/configs/am35xx_pfc200_xload_defconfig
> rename arch/arm/configs/{am335x_defconfig => omap_defconfig} (96%)
> create mode 100644 arch/arm/dts/am35xx-pfc-750_820x.dts
> create mode 100644 arch/arm/dts/am3xxx-pfc-nandparts.dtsi
> create mode 100644 arch/arm/mach-omap/am35xx_emif4.c
> create mode 100644 arch/arm/mach-omap/am3xxx.c
> create mode 100644 arch/arm/mach-omap/include/mach/am3xxx-silicon.h
> create mode 100644 arch/arm/mach-omap/include/mach/emif4.h
> rename arch/arm/mach-omap/s32k_clksource.c => drivers/clocksource/timer-ti-32k.c (73%)
> rename arch/arm/mach-omap/dmtimer.c => drivers/clocksource/timer-ti-dm.c (72%)
> create mode 100644 images/Makefile.am35xx
> delete mode 100644 include/platform_data/eth-davinci-emac.h
>
> --
> 2.19.1
>
>
> _______________________________________________
> barebox mailing list
> barebox@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
next prev parent reply other threads:[~2018-12-14 16:23 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-12-14 14:17 Sascha Hauer
2018-12-14 14:17 ` [PATCH 01/23] net: davinci-emac: fix buggy channel tear down Sascha Hauer
2018-12-14 14:17 ` [PATCH 02/23] net: davinci-emac: Add timeout to polling loop Sascha Hauer
2018-12-14 14:17 ` [PATCH 03/23] net: davinci-emac: switch to device tree support Sascha Hauer
2018-12-14 14:17 ` [PATCH 04/23] mci: omap: Improve error handling Sascha Hauer
2018-12-14 14:17 ` [PATCH 05/23] mci: omap: use IS_ENABLED() rather than #ifdef Sascha Hauer
2018-12-14 14:17 ` [PATCH 06/23] mtd: nand: omap: Use dev_dbg when a struct device * is available Sascha Hauer
2018-12-14 14:17 ` [PATCH 07/23] mtd: nand: omap: Fix hamming correct return values Sascha Hauer
2018-12-14 14:17 ` [PATCH 08/23] mtd: nand: omap: Disable subpage reads in hardware ecc mode Sascha Hauer
2018-12-14 14:17 ` [PATCH 09/23] mtd: nand: omap: remove unused function argument Sascha Hauer
2018-12-14 14:17 ` [PATCH 10/23] mtd: nand: omap: fix bch8_hw_romcode ecc layout Sascha Hauer
2018-12-14 14:17 ` [PATCH 11/23] mtd: nand: omap: set eccbytes correctly Sascha Hauer
2018-12-14 14:17 ` [PATCH 12/23] mtd: nand: omap: unbreak BCH8 support Sascha Hauer
2018-12-14 14:17 ` [PATCH 13/23] ARM: omap: Add missing include Sascha Hauer
2018-12-14 14:17 ` [PATCH 14/23] ARM: omap: dmtimer: Turn into a driver Sascha Hauer
2018-12-17 13:37 ` Teresa Remmet
2018-12-18 7:46 ` Sascha Hauer
2018-12-14 14:17 ` [PATCH 15/23] ARM: omap: 32ktimer: " Sascha Hauer
2018-12-14 14:17 ` [PATCH 16/23] ARM: omap: Add AM35XX support Sascha Hauer
2018-12-14 14:17 ` [PATCH 17/23] ARM: omap: enable am33xx_uart_soft_reset for AM35xx Sascha Hauer
2018-12-14 14:17 ` [PATCH 18/23] ARM: omap3: Add support for reset reason detection Sascha Hauer
2018-12-14 14:17 ` [PATCH 19/23] ARM: omap: Add AM3517 specific mux configuration Sascha Hauer
2018-12-14 14:17 ` [PATCH 20/23] ARM: omap: Add emif4 support for AM3517 Sascha Hauer
2018-12-14 14:17 ` [PATCH 21/23] ARM: omap: AM3517: Change default clock rate " Sascha Hauer
2018-12-14 14:17 ` [PATCH 22/23] ARM: omap: Add board support for WAGO pfc200 platform Sascha Hauer
2019-01-07 11:40 ` Heinrich.Toews
2019-01-07 11:46 ` Sascha Hauer
2018-12-14 14:17 ` [PATCH 23/23] ARM: omap: am33xx_defconfig: Enable more boards and rename Sascha Hauer
2018-12-14 16:22 ` Ladislav Michl [this message]
2018-12-14 19:32 ` [PATCH 00/23] AM3517 support Sascha Hauer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181214162249.GA19868@lenoch \
--to=ladis@linux-mips.org \
--cc=barebox@lists.infradead.org \
--cc=s.hauer@pengutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox