From: Andrey Smirnov <andrew.smirnov@gmail.com>
To: barebox@lists.infradead.org
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Subject: [PATCH v4 09/17] reset: Add i.MX7 SRC reset driver
Date: Wed, 16 Jan 2019 18:16:52 -0800 [thread overview]
Message-ID: <20190117021700.4443-10-andrew.smirnov@gmail.com> (raw)
In-Reply-To: <20190117021700.4443-1-andrew.smirnov@gmail.com>
Port of a Linux commit abf97755ae31aaaf35156438dd3036e96f66da83
Add reset controller driver exposing various reset faculties,
implemented by System Reset Controller IP block.
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Linux commit 26fce0557fa639fb7bbc33e31a57cff7df25c3a0 was squashed
here as well:
reset: imx7: Fix always writing bits as 0
Right now the only user of reset-imx7 is pci-imx6 and the
reset_control_assert and deassert calls on pciephy_reset don't toggle
the PCIEPHY_BTN and PCIEPHY_G_RST bits as expected. Fix this by writing
1 or 0 respectively.
The reference manual is not very clear regarding SRC_PCIEPHY_RCR but for
other registers like MIPIPHY and HSICPHY the bits are explicitly
documented as "1 means assert, 0 means deassert".
The values are still reversed for IMX7_RESET_PCIE_CTRL_APPS_EN.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
---
drivers/reset/Kconfig | 11 +++
drivers/reset/Makefile | 1 +
drivers/reset/reset-imx7.c | 151 +++++++++++++++++++++++++++++++++++++
3 files changed, 163 insertions(+)
create mode 100644 drivers/reset/reset-imx7.c
diff --git a/drivers/reset/Kconfig b/drivers/reset/Kconfig
index c9d04f7978..caf1dc9acb 100644
--- a/drivers/reset/Kconfig
+++ b/drivers/reset/Kconfig
@@ -11,3 +11,14 @@ menuconfig RESET_CONTROLLER
via GPIOs or SoC-internal reset controller modules.
If unsure, say no.
+
+if RESET_CONTROLLER
+
+config RESET_IMX7
+ bool "i.MX7 Reset Driver"
+ default SOC_IMX7D
+ select MFD_SYSCON
+ help
+ This enables the reset controller driver for i.MX7 SoCs.
+
+endif
diff --git a/drivers/reset/Makefile b/drivers/reset/Makefile
index 52b10cd480..0b55caa204 100644
--- a/drivers/reset/Makefile
+++ b/drivers/reset/Makefile
@@ -1,2 +1,3 @@
obj-$(CONFIG_RESET_CONTROLLER) += core.o
obj-$(CONFIG_ARCH_SOCFPGA) += reset-socfpga.o
+obj-$(CONFIG_RESET_IMX7) += reset-imx7.o
diff --git a/drivers/reset/reset-imx7.c b/drivers/reset/reset-imx7.c
new file mode 100644
index 0000000000..6dc5de16a7
--- /dev/null
+++ b/drivers/reset/reset-imx7.c
@@ -0,0 +1,151 @@
+/*
+ * Copyright (c) 2017, Impinj, Inc.
+ *
+ * i.MX7 System Reset Controller (SRC) driver
+ *
+ * Author: Andrey Smirnov <andrew.smirnov@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <dt-bindings/reset/imx7-reset.h>
+#include <init.h>
+#include <linux/err.h>
+#include <linux/reset-controller.h>
+#include <mfd/syscon.h>
+#include <regmap.h>
+
+struct imx7_src {
+ struct reset_controller_dev rcdev;
+ struct regmap *regmap;
+};
+
+enum imx7_src_registers {
+ SRC_A7RCR0 = 0x0004,
+ SRC_M4RCR = 0x000c,
+ SRC_ERCR = 0x0014,
+ SRC_HSICPHY_RCR = 0x001c,
+ SRC_USBOPHY1_RCR = 0x0020,
+ SRC_USBOPHY2_RCR = 0x0024,
+ SRC_MIPIPHY_RCR = 0x0028,
+ SRC_PCIEPHY_RCR = 0x002c,
+ SRC_DDRC_RCR = 0x1000,
+};
+
+struct imx7_src_signal {
+ unsigned int offset, bit;
+};
+
+static const struct imx7_src_signal imx7_src_signals[IMX7_RESET_NUM] = {
+ [IMX7_RESET_A7_CORE_POR_RESET0] = { SRC_A7RCR0, BIT(0) },
+ [IMX7_RESET_A7_CORE_POR_RESET1] = { SRC_A7RCR0, BIT(1) },
+ [IMX7_RESET_A7_CORE_RESET0] = { SRC_A7RCR0, BIT(4) },
+ [IMX7_RESET_A7_CORE_RESET1] = { SRC_A7RCR0, BIT(5) },
+ [IMX7_RESET_A7_DBG_RESET0] = { SRC_A7RCR0, BIT(8) },
+ [IMX7_RESET_A7_DBG_RESET1] = { SRC_A7RCR0, BIT(9) },
+ [IMX7_RESET_A7_ETM_RESET0] = { SRC_A7RCR0, BIT(12) },
+ [IMX7_RESET_A7_ETM_RESET1] = { SRC_A7RCR0, BIT(13) },
+ [IMX7_RESET_A7_SOC_DBG_RESET] = { SRC_A7RCR0, BIT(20) },
+ [IMX7_RESET_A7_L2RESET] = { SRC_A7RCR0, BIT(21) },
+ [IMX7_RESET_SW_M4C_RST] = { SRC_M4RCR, BIT(1) },
+ [IMX7_RESET_SW_M4P_RST] = { SRC_M4RCR, BIT(2) },
+ [IMX7_RESET_EIM_RST] = { SRC_ERCR, BIT(0) },
+ [IMX7_RESET_HSICPHY_PORT_RST] = { SRC_HSICPHY_RCR, BIT(1) },
+ [IMX7_RESET_USBPHY1_POR] = { SRC_USBOPHY1_RCR, BIT(0) },
+ [IMX7_RESET_USBPHY1_PORT_RST] = { SRC_USBOPHY1_RCR, BIT(1) },
+ [IMX7_RESET_USBPHY2_POR] = { SRC_USBOPHY2_RCR, BIT(0) },
+ [IMX7_RESET_USBPHY2_PORT_RST] = { SRC_USBOPHY2_RCR, BIT(1) },
+ [IMX7_RESET_MIPI_PHY_MRST] = { SRC_MIPIPHY_RCR, BIT(1) },
+ [IMX7_RESET_MIPI_PHY_SRST] = { SRC_MIPIPHY_RCR, BIT(2) },
+ [IMX7_RESET_PCIEPHY] = { SRC_PCIEPHY_RCR, BIT(2) | BIT(1) },
+ [IMX7_RESET_PCIEPHY_PERST] = { SRC_PCIEPHY_RCR, BIT(3) },
+ [IMX7_RESET_PCIE_CTRL_APPS_EN] = { SRC_PCIEPHY_RCR, BIT(6) },
+ [IMX7_RESET_DDRC_PRST] = { SRC_DDRC_RCR, BIT(0) },
+ [IMX7_RESET_DDRC_CORE_RST] = { SRC_DDRC_RCR, BIT(1) },
+};
+
+static struct imx7_src *to_imx7_src(struct reset_controller_dev *rcdev)
+{
+ return container_of(rcdev, struct imx7_src, rcdev);
+}
+
+static int imx7_reset_set(struct reset_controller_dev *rcdev,
+ unsigned long id, bool assert)
+{
+ struct imx7_src *imx7src = to_imx7_src(rcdev);
+ const struct imx7_src_signal *signal = &imx7_src_signals[id];
+ unsigned int value = assert ? signal->bit : 0;;
+
+ switch (id) {
+ case IMX7_RESET_PCIEPHY:
+ /*
+ * wait for more than 10us to release phy g_rst and
+ * btnrst
+ */
+ if (!assert)
+ udelay(10);
+ break;
+
+ case IMX7_RESET_PCIE_CTRL_APPS_EN:
+ value = (assert) ? 0 : signal->bit;
+ break;
+ }
+
+ return regmap_update_bits(imx7src->regmap,
+ signal->offset, signal->bit, value);
+}
+
+static int imx7_reset_assert(struct reset_controller_dev *rcdev,
+ unsigned long id)
+{
+ return imx7_reset_set(rcdev, id, true);
+}
+
+static int imx7_reset_deassert(struct reset_controller_dev *rcdev,
+ unsigned long id)
+{
+ return imx7_reset_set(rcdev, id, false);
+}
+
+static struct reset_control_ops imx7_reset_ops = {
+ .assert = imx7_reset_assert,
+ .deassert = imx7_reset_deassert,
+};
+
+static int imx7_reset_probe(struct device_d *dev)
+{
+ struct imx7_src *imx7src;
+
+ imx7src = xzalloc(sizeof(*imx7src));
+ imx7src->regmap = syscon_node_to_regmap(dev->device_node);
+ if (IS_ERR(imx7src->regmap)) {
+ dev_err(dev, "Unable to get imx7-src regmap");
+ return PTR_ERR(imx7src->regmap);
+ }
+
+ imx7src->rcdev.nr_resets = IMX7_RESET_NUM;
+ imx7src->rcdev.ops = &imx7_reset_ops;
+ imx7src->rcdev.of_node = dev->device_node;
+
+ return reset_controller_register(&imx7src->rcdev);
+}
+
+static const struct of_device_id imx7_reset_dt_ids[] = {
+ { .compatible = "fsl,imx7d-src", },
+ { /* sentinel */ },
+};
+
+static struct driver_d imx7_reset_driver = {
+ .name = "imx7d-src",
+ .probe = imx7_reset_probe,
+ .of_compatible = DRV_OF_COMPAT(imx7_reset_dt_ids),
+};
+device_platform_driver(imx7_reset_driver);
--
2.20.1
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
next prev parent reply other threads:[~2019-01-17 2:17 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-01-17 2:16 [PATCH v4 00/17] PCIe support for i.MX7 Andrey Smirnov
2019-01-17 2:16 ` [PATCH v4 01/17] regulator: Convert drivers to use struct regulator_desc Andrey Smirnov
2019-01-17 2:16 ` [PATCH v4 02/17] regulator: Port basic regmap regulator functions Andrey Smirnov
2019-01-17 2:16 ` [PATCH v4 03/17] regulator: Add support for setting regulator's voltage Andrey Smirnov
2019-01-17 2:16 ` [PATCH v4 04/17] base: driver: Drop redundant list_empty() check Andrey Smirnov
2019-01-17 2:16 ` [PATCH v4 05/17] regulator: Assume probe deferral instead of missing regulator Andrey Smirnov
2019-01-17 2:16 ` [PATCH v4 06/17] regulator: Port ANATOP driver from Linux Andrey Smirnov
2019-01-17 2:16 ` [PATCH v4 07/17] drivers: base: Port power management code " Andrey Smirnov
2019-01-17 2:16 ` [PATCH v4 08/17] soc: imx: Add GPCv2 power gating driver Andrey Smirnov
2019-01-17 2:16 ` Andrey Smirnov [this message]
2019-01-17 2:16 ` [PATCH v4 10/17] reset: Mark local functions as static Andrey Smirnov
2019-01-17 2:16 ` [PATCH v4 11/17] PCI: imx6: Add code to support i.MX7D Andrey Smirnov
2019-01-17 2:16 ` [PATCH v4 12/17] PCI: imx6: Allow probe deferral by reset GPIO Andrey Smirnov
2019-01-17 2:16 ` [PATCH v4 13/17] PCI: imx6: Do not wait for speed change on i.MX7 Andrey Smirnov
2019-01-17 2:16 ` [PATCH v4 14/17] PCI: imx6: Do not switch speed if Gen2 is disabled Andrey Smirnov
2019-01-17 2:16 ` [PATCH v4 15/17] PCI: imx6: Fix spelling mistake: "contol" -> "control" Andrey Smirnov
2019-01-17 2:16 ` [PATCH v4 16/17] PCI: imx6: Drop unnecessary root_bus_nr setting Andrey Smirnov
2019-01-17 2:17 ` [PATCH v4 17/17] PCI: imx6: Port imx6_pcie_ltssm_enable() Andrey Smirnov
2019-01-17 8:46 ` [PATCH v4 00/17] PCIe support for i.MX7 Sascha Hauer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190117021700.4443-10-andrew.smirnov@gmail.com \
--to=andrew.smirnov@gmail.com \
--cc=barebox@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox