mail archive of the barebox mailing list
 help / color / mirror / Atom feed
From: Andrey Smirnov <andrew.smirnov@gmail.com>
To: barebox@lists.infradead.org
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Subject: [PATCH 24/25] usb: Port Microchip USB251x USB hub driver from Linux
Date: Tue, 19 Feb 2019 23:29:29 -0800	[thread overview]
Message-ID: <20190220072930.14300-25-andrew.smirnov@gmail.com> (raw)
In-Reply-To: <20190220072930.14300-1-andrew.smirnov@gmail.com>

Port Microchip USB251x USB hub driver from Linux. Needed by ZII's
i.MX8MQ boards.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
---
 drivers/usb/Kconfig         |   2 +
 drivers/usb/Makefile        |   1 +
 drivers/usb/misc/Kconfig    |  14 +
 drivers/usb/misc/Makefile   |   6 +
 drivers/usb/misc/usb251xb.c | 672 ++++++++++++++++++++++++++++++++++++
 5 files changed, 695 insertions(+)
 create mode 100644 drivers/usb/misc/Kconfig
 create mode 100644 drivers/usb/misc/Makefile
 create mode 100644 drivers/usb/misc/usb251xb.c

diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig
index ee33e0f28..8ff3d18d4 100644
--- a/drivers/usb/Kconfig
+++ b/drivers/usb/Kconfig
@@ -17,6 +17,8 @@ source drivers/usb/otg/Kconfig
 
 source drivers/usb/storage/Kconfig
 
+source "drivers/usb/misc/Kconfig"
+
 endif
 
 source drivers/usb/gadget/Kconfig
diff --git a/drivers/usb/Makefile b/drivers/usb/Makefile
index 13fca2cbd..9e9809950 100644
--- a/drivers/usb/Makefile
+++ b/drivers/usb/Makefile
@@ -6,4 +6,5 @@ obj-$(CONFIG_USB_GADGET)	+= gadget/
 obj-$(CONFIG_USB_STORAGE)	+= storage/
 obj-y += host/
 obj-y += otg/
+obj-$(CONFIG_USB)		+= misc/
 
diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig
new file mode 100644
index 000000000..7d6c9da59
--- /dev/null
+++ b/drivers/usb/misc/Kconfig
@@ -0,0 +1,14 @@
+#
+# USB Miscellaneous driver configuration
+#
+comment "USB Miscellaneous drivers"
+
+config USB_HUB_USB251XB
+	bool "USB251XB Hub Controller Configuration Driver"
+	depends on I2C
+	select NLS
+	help
+	  This option enables support for configuration via SMBus of the
+	  Microchip USB251x/xBi USB 2.0 Hub Controller series. Configuration
+	  parameters may be set in devicetree or platform data.
+	  Say Y or M here if you need to configure such a device via SMBus.
diff --git a/drivers/usb/misc/Makefile b/drivers/usb/misc/Makefile
new file mode 100644
index 000000000..fb69c454b
--- /dev/null
+++ b/drivers/usb/misc/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for the rest of the USB drivers
+# (the ones that don't fit into any other categories)
+#
+obj-$(CONFIG_USB_HUB_USB251XB)		+= usb251xb.o
diff --git a/drivers/usb/misc/usb251xb.c b/drivers/usb/misc/usb251xb.c
new file mode 100644
index 000000000..0b721f6d4
--- /dev/null
+++ b/drivers/usb/misc/usb251xb.c
@@ -0,0 +1,672 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Driver for Microchip USB251xB USB 2.0 Hi-Speed Hub Controller
+ * Configuration via SMBus.
+ *
+ * Copyright (c) 2017 SKIDATA AG
+ *
+ * This work is based on the USB3503 driver by Dongjin Kim and
+ * a not-accepted patch by Fabien Lahoudere, see:
+ * https://patchwork.kernel.org/patch/9257715/
+ */
+
+#include <common.h>
+#include <init.h>
+#include <driver.h>
+#include <i2c/i2c.h>
+#include <of.h>
+#include <gpio.h>
+#include <of_gpio.h>
+#include <of_device.h>
+
+#include <linux/nls.h>
+
+/* Internal Register Set Addresses & Default Values acc. to DS00001692C */
+#define USB251XB_ADDR_VENDOR_ID_LSB	0x00
+#define USB251XB_ADDR_VENDOR_ID_MSB	0x01
+#define USB251XB_DEF_VENDOR_ID		0x0424
+
+#define USB251XB_ADDR_PRODUCT_ID_LSB	0x02
+#define USB251XB_ADDR_PRODUCT_ID_MSB	0x03
+#define USB251XB_DEF_PRODUCT_ID_12	0x2512 /* USB2512B/12Bi */
+#define USB251XB_DEF_PRODUCT_ID_13	0x2513 /* USB2513B/13Bi */
+#define USB251XB_DEF_PRODUCT_ID_14	0x2514 /* USB2514B/14Bi */
+#define USB251XB_DEF_PRODUCT_ID_17	0x2517 /* USB2517/17i */
+
+#define USB251XB_ADDR_DEVICE_ID_LSB	0x04
+#define USB251XB_ADDR_DEVICE_ID_MSB	0x05
+#define USB251XB_DEF_DEVICE_ID		0x0BB3
+
+#define USB251XB_ADDR_CONFIG_DATA_1	0x06
+#define USB251XB_DEF_CONFIG_DATA_1	0x9B
+#define USB251XB_ADDR_CONFIG_DATA_2	0x07
+#define USB251XB_DEF_CONFIG_DATA_2	0x20
+#define USB251XB_ADDR_CONFIG_DATA_3	0x08
+#define USB251XB_DEF_CONFIG_DATA_3	0x02
+
+#define USB251XB_ADDR_NON_REMOVABLE_DEVICES	0x09
+#define USB251XB_DEF_NON_REMOVABLE_DEVICES	0x00
+
+#define USB251XB_ADDR_PORT_DISABLE_SELF	0x0A
+#define USB251XB_DEF_PORT_DISABLE_SELF	0x00
+#define USB251XB_ADDR_PORT_DISABLE_BUS	0x0B
+#define USB251XB_DEF_PORT_DISABLE_BUS	0x00
+
+#define USB251XB_ADDR_MAX_POWER_SELF	0x0C
+#define USB251XB_DEF_MAX_POWER_SELF	0x01
+#define USB251XB_ADDR_MAX_POWER_BUS	0x0D
+#define USB251XB_DEF_MAX_POWER_BUS	0x32
+
+#define USB251XB_ADDR_MAX_CURRENT_SELF	0x0E
+#define USB251XB_DEF_MAX_CURRENT_SELF	0x01
+#define USB251XB_ADDR_MAX_CURRENT_BUS	0x0F
+#define USB251XB_DEF_MAX_CURRENT_BUS	0x32
+
+#define USB251XB_ADDR_POWER_ON_TIME	0x10
+#define USB251XB_DEF_POWER_ON_TIME	0x32
+
+#define USB251XB_ADDR_LANGUAGE_ID_HIGH	0x11
+#define USB251XB_ADDR_LANGUAGE_ID_LOW	0x12
+#define USB251XB_DEF_LANGUAGE_ID	0x0000
+
+#define USB251XB_STRING_BUFSIZE			62
+#define USB251XB_ADDR_MANUFACTURER_STRING_LEN	0x13
+#define USB251XB_ADDR_MANUFACTURER_STRING	0x16
+#define USB251XB_DEF_MANUFACTURER_STRING	"Microchip"
+
+#define USB251XB_ADDR_PRODUCT_STRING_LEN	0x14
+#define USB251XB_ADDR_PRODUCT_STRING		0x54
+#define USB251XB_DEF_PRODUCT_STRING		"USB251xB/xBi/7i"
+
+#define USB251XB_ADDR_SERIAL_STRING_LEN		0x15
+#define USB251XB_ADDR_SERIAL_STRING		0x92
+#define USB251XB_DEF_SERIAL_STRING		""
+
+#define USB251XB_ADDR_BATTERY_CHARGING_ENABLE	0xD0
+#define USB251XB_DEF_BATTERY_CHARGING_ENABLE	0x00
+
+#define USB251XB_ADDR_BOOST_UP	0xF6
+#define USB251XB_DEF_BOOST_UP	0x00
+#define USB251XB_ADDR_BOOST_57	0xF7
+#define USB251XB_DEF_BOOST_57	0x00
+#define USB251XB_ADDR_BOOST_14	0xF8
+#define USB251XB_DEF_BOOST_14	0x00
+
+#define USB251XB_ADDR_PORT_SWAP	0xFA
+#define USB251XB_DEF_PORT_SWAP	0x00
+
+#define USB251XB_ADDR_PORT_MAP_12	0xFB
+#define USB251XB_DEF_PORT_MAP_12	0x00
+#define USB251XB_ADDR_PORT_MAP_34	0xFC
+#define USB251XB_DEF_PORT_MAP_34	0x00 /* USB251{3B/i,4B/i,7/i} only */
+#define USB251XB_ADDR_PORT_MAP_56	0xFD
+#define USB251XB_DEF_PORT_MAP_56	0x00 /* USB2517/i only */
+#define USB251XB_ADDR_PORT_MAP_7	0xFE
+#define USB251XB_DEF_PORT_MAP_7		0x00 /* USB2517/i only */
+
+#define USB251XB_ADDR_STATUS_COMMAND		0xFF
+#define USB251XB_STATUS_COMMAND_SMBUS_DOWN	0x04
+#define USB251XB_STATUS_COMMAND_RESET		0x02
+#define USB251XB_STATUS_COMMAND_ATTACH		0x01
+
+#define USB251XB_I2C_REG_SZ	0x100
+#define USB251XB_I2C_WRITE_SZ	0x10
+
+#define DRIVER_NAME	"usb251xb"
+#define DRIVER_DESC	"Microchip USB 2.0 Hi-Speed Hub Controller"
+
+struct usb251xb {
+	struct device_d *dev;
+	struct i2c_client *i2c;
+	u8 skip_config;
+	int gpio_reset;
+	u16 vendor_id;
+	u16 product_id;
+	u16 device_id;
+	u8  conf_data1;
+	u8  conf_data2;
+	u8  conf_data3;
+	u8  non_rem_dev;
+	u8  port_disable_sp;
+	u8  port_disable_bp;
+	u8  max_power_sp;
+	u8  max_power_bp;
+	u8  max_current_sp;
+	u8  max_current_bp;
+	u8  power_on_time;
+	u16 lang_id;
+	u8 manufacturer_len;
+	u8 product_len;
+	u8 serial_len;
+	char manufacturer[USB251XB_STRING_BUFSIZE];
+	char product[USB251XB_STRING_BUFSIZE];
+	char serial[USB251XB_STRING_BUFSIZE];
+	u8  bat_charge_en;
+	u8  boost_up;
+	u8  boost_57;
+	u8  boost_14;
+	u8  port_swap;
+	u8  port_map12;
+	u8  port_map34;
+	u8  port_map56;
+	u8  port_map7;
+	u8  status;
+};
+
+struct usb251xb_data {
+	u16 product_id;
+	u8 port_cnt;
+	bool led_support;
+	bool bat_support;
+	char product_str[USB251XB_STRING_BUFSIZE / 2]; /* ASCII string */
+};
+
+static const struct usb251xb_data usb2512b_data = {
+	.product_id = 0x2512,
+	.port_cnt = 2,
+	.led_support = false,
+	.bat_support = true,
+	.product_str = "USB2512B",
+};
+
+static const struct usb251xb_data usb2512bi_data = {
+	.product_id = 0x2512,
+	.port_cnt = 2,
+	.led_support = false,
+	.bat_support = true,
+	.product_str = "USB2512Bi",
+};
+
+static const struct usb251xb_data usb2513b_data = {
+	.product_id = 0x2513,
+	.port_cnt = 3,
+	.led_support = false,
+	.bat_support = true,
+	.product_str = "USB2513B",
+};
+
+static const struct usb251xb_data usb2513bi_data = {
+	.product_id = 0x2513,
+	.port_cnt = 3,
+	.led_support = false,
+	.bat_support = true,
+	.product_str = "USB2513Bi",
+};
+
+static const struct usb251xb_data usb2514b_data = {
+	.product_id = 0x2514,
+	.port_cnt = 4,
+	.led_support = false,
+	.bat_support = true,
+	.product_str = "USB2514B",
+};
+
+static const struct usb251xb_data usb2514bi_data = {
+	.product_id = 0x2514,
+	.port_cnt = 4,
+	.led_support = false,
+	.bat_support = true,
+	.product_str = "USB2514Bi",
+};
+
+static const struct usb251xb_data usb2517_data = {
+	.product_id = 0x2517,
+	.port_cnt = 7,
+	.led_support = true,
+	.bat_support = false,
+	.product_str = "USB2517",
+};
+
+static const struct usb251xb_data usb2517i_data = {
+	.product_id = 0x2517,
+	.port_cnt = 7,
+	.led_support = true,
+	.bat_support = false,
+	.product_str = "USB2517i",
+};
+
+static void usb251xb_reset(struct usb251xb *hub, int state)
+{
+	if (!gpio_is_valid(hub->gpio_reset))
+		return;
+
+	gpio_set_active(hub->gpio_reset, state);
+
+	/* wait for hub recovery/stabilization */
+	if (!state)
+		udelay(750);	/* >=500us at power on */
+	else
+		udelay(10);	/* >=1us at power down */
+}
+
+static int usb251xb_connect(struct usb251xb *hub)
+{
+	struct device_d *dev = hub->dev;
+	int err, i;
+	char i2c_wb[USB251XB_I2C_REG_SZ];
+
+	memset(i2c_wb, 0, USB251XB_I2C_REG_SZ);
+
+	if (hub->skip_config) {
+		dev_info(dev, "Skip hub configuration, only attach.\n");
+		i2c_wb[0] = 0x01;
+		i2c_wb[1] = USB251XB_STATUS_COMMAND_ATTACH;
+
+		usb251xb_reset(hub, 0);
+
+		err = i2c_smbus_write_i2c_block_data(hub->i2c,
+				USB251XB_ADDR_STATUS_COMMAND, 2, i2c_wb);
+		if (err) {
+			dev_err(dev, "attaching hub failed: %d\n", err);
+			return err;
+		}
+		return 0;
+	}
+
+	i2c_wb[USB251XB_ADDR_VENDOR_ID_MSB]     = (hub->vendor_id >> 8) & 0xFF;
+	i2c_wb[USB251XB_ADDR_VENDOR_ID_LSB]     = hub->vendor_id & 0xFF;
+	i2c_wb[USB251XB_ADDR_PRODUCT_ID_MSB]    = (hub->product_id >> 8) & 0xFF;
+	i2c_wb[USB251XB_ADDR_PRODUCT_ID_LSB]    = hub->product_id & 0xFF;
+	i2c_wb[USB251XB_ADDR_DEVICE_ID_MSB]     = (hub->device_id >> 8) & 0xFF;
+	i2c_wb[USB251XB_ADDR_DEVICE_ID_LSB]     = hub->device_id & 0xFF;
+	i2c_wb[USB251XB_ADDR_CONFIG_DATA_1]     = hub->conf_data1;
+	i2c_wb[USB251XB_ADDR_CONFIG_DATA_2]     = hub->conf_data2;
+	i2c_wb[USB251XB_ADDR_CONFIG_DATA_3]     = hub->conf_data3;
+	i2c_wb[USB251XB_ADDR_NON_REMOVABLE_DEVICES] = hub->non_rem_dev;
+	i2c_wb[USB251XB_ADDR_PORT_DISABLE_SELF] = hub->port_disable_sp;
+	i2c_wb[USB251XB_ADDR_PORT_DISABLE_BUS]  = hub->port_disable_bp;
+	i2c_wb[USB251XB_ADDR_MAX_POWER_SELF]    = hub->max_power_sp;
+	i2c_wb[USB251XB_ADDR_MAX_POWER_BUS]     = hub->max_power_bp;
+	i2c_wb[USB251XB_ADDR_MAX_CURRENT_SELF]  = hub->max_current_sp;
+	i2c_wb[USB251XB_ADDR_MAX_CURRENT_BUS]   = hub->max_current_bp;
+	i2c_wb[USB251XB_ADDR_POWER_ON_TIME]     = hub->power_on_time;
+	i2c_wb[USB251XB_ADDR_LANGUAGE_ID_HIGH]  = (hub->lang_id >> 8) & 0xFF;
+	i2c_wb[USB251XB_ADDR_LANGUAGE_ID_LOW]   = hub->lang_id & 0xFF;
+	i2c_wb[USB251XB_ADDR_MANUFACTURER_STRING_LEN] = hub->manufacturer_len;
+	i2c_wb[USB251XB_ADDR_PRODUCT_STRING_LEN]      = hub->product_len;
+	i2c_wb[USB251XB_ADDR_SERIAL_STRING_LEN]       = hub->serial_len;
+	memcpy(&i2c_wb[USB251XB_ADDR_MANUFACTURER_STRING], hub->manufacturer,
+	       USB251XB_STRING_BUFSIZE);
+	memcpy(&i2c_wb[USB251XB_ADDR_SERIAL_STRING], hub->serial,
+	       USB251XB_STRING_BUFSIZE);
+	memcpy(&i2c_wb[USB251XB_ADDR_PRODUCT_STRING], hub->product,
+	       USB251XB_STRING_BUFSIZE);
+	i2c_wb[USB251XB_ADDR_BATTERY_CHARGING_ENABLE] = hub->bat_charge_en;
+	i2c_wb[USB251XB_ADDR_BOOST_UP]          = hub->boost_up;
+	i2c_wb[USB251XB_ADDR_BOOST_57]          = hub->boost_57;
+	i2c_wb[USB251XB_ADDR_BOOST_14]          = hub->boost_14;
+	i2c_wb[USB251XB_ADDR_PORT_SWAP]         = hub->port_swap;
+	i2c_wb[USB251XB_ADDR_PORT_MAP_12]       = hub->port_map12;
+	i2c_wb[USB251XB_ADDR_PORT_MAP_34]       = hub->port_map34;
+	i2c_wb[USB251XB_ADDR_PORT_MAP_56]       = hub->port_map56;
+	i2c_wb[USB251XB_ADDR_PORT_MAP_7]        = hub->port_map7;
+	i2c_wb[USB251XB_ADDR_STATUS_COMMAND] = USB251XB_STATUS_COMMAND_ATTACH;
+
+	usb251xb_reset(hub, 0);
+
+	/* write registers */
+	for (i = 0; i < (USB251XB_I2C_REG_SZ / USB251XB_I2C_WRITE_SZ); i++) {
+		int offset = i * USB251XB_I2C_WRITE_SZ;
+		char wbuf[USB251XB_I2C_WRITE_SZ + 1];
+
+		/* The first data byte transferred tells the hub how many data
+		 * bytes will follow (byte count).
+		 */
+		wbuf[0] = USB251XB_I2C_WRITE_SZ;
+		memcpy(&wbuf[1], &i2c_wb[offset], USB251XB_I2C_WRITE_SZ);
+
+		dev_dbg(dev, "writing %d byte block %d to 0x%02X\n",
+			USB251XB_I2C_WRITE_SZ, i, offset);
+
+		err = i2c_smbus_write_i2c_block_data(hub->i2c, offset,
+						     USB251XB_I2C_WRITE_SZ + 1,
+						     wbuf);
+		if (err)
+			goto out_err;
+	}
+
+	dev_info(dev, "Hub configuration was successful.\n");
+	return 0;
+
+out_err:
+	dev_err(dev, "configuring block %d failed: %d\n", i, err);
+	return err;
+}
+
+#ifdef CONFIG_OFDEVICE
+static int usb251xb_get_ofdata(struct usb251xb *hub,
+			       struct usb251xb_data *data)
+{
+	struct device_d *dev = hub->dev;
+	struct device_node *np = dev->device_node;
+	int len, err, i;
+	u32 property_u32 = 0;
+	const u32 *cproperty_u32;
+	const char *cproperty_char;
+	enum of_gpio_flags of_flags;
+	unsigned long flags = GPIOF_OUT_INIT_ACTIVE;
+	char str[USB251XB_STRING_BUFSIZE / 2];
+
+	if (!np) {
+		dev_err(dev, "failed to get ofdata\n");
+		return -ENODEV;
+	}
+
+	if (of_get_property(np, "skip-config", NULL))
+		hub->skip_config = 1;
+	else
+		hub->skip_config = 0;
+
+	hub->gpio_reset = of_get_named_gpio_flags(np, "reset-gpios", 0,
+						  &of_flags);
+	if (gpio_is_valid(hub->gpio_reset)) {
+		char *name;
+		int ret;
+
+		if (of_flags & OF_GPIO_ACTIVE_LOW)
+			flags |= GPIOF_ACTIVE_LOW;
+
+		name = basprintf("%s reset", dev_name(dev));
+		ret  = gpio_request_one(hub->gpio_reset, flags, name);
+		if (ret < 0)
+			return ret;
+	} else if (hub->gpio_reset == -EPROBE_DEFER) {
+		return -EPROBE_DEFER;
+	} else {
+		err = hub->gpio_reset;
+		dev_err(dev, "unable to request GPIO reset pin (%d)\n", err);
+		return err;
+	}
+
+	if (of_property_read_u16_array(np, "vendor-id", &hub->vendor_id, 1))
+		hub->vendor_id = USB251XB_DEF_VENDOR_ID;
+
+	if (of_property_read_u16_array(np, "product-id",
+				       &hub->product_id, 1))
+		hub->product_id = data->product_id;
+
+	if (of_property_read_u16_array(np, "device-id", &hub->device_id, 1))
+		hub->device_id = USB251XB_DEF_DEVICE_ID;
+
+	hub->conf_data1 = USB251XB_DEF_CONFIG_DATA_1;
+	if (of_get_property(np, "self-powered", NULL)) {
+		hub->conf_data1 |= BIT(7);
+
+		/* Configure Over-Current sens when self-powered */
+		hub->conf_data1 &= ~BIT(2);
+		if (of_get_property(np, "ganged-sensing", NULL))
+			hub->conf_data1 &= ~BIT(1);
+		else if (of_get_property(np, "individual-sensing", NULL))
+			hub->conf_data1 |= BIT(1);
+	} else if (of_get_property(np, "bus-powered", NULL)) {
+		hub->conf_data1 &= ~BIT(7);
+
+		/* Disable Over-Current sense when bus-powered */
+		hub->conf_data1 |= BIT(2);
+	}
+
+	if (of_get_property(np, "disable-hi-speed", NULL))
+		hub->conf_data1 |= BIT(5);
+
+	if (of_get_property(np, "multi-tt", NULL))
+		hub->conf_data1 |= BIT(4);
+	else if (of_get_property(np, "single-tt", NULL))
+		hub->conf_data1 &= ~BIT(4);
+
+	if (of_get_property(np, "disable-eop", NULL))
+		hub->conf_data1 |= BIT(3);
+
+	if (of_get_property(np, "individual-port-switching", NULL))
+		hub->conf_data1 |= BIT(0);
+	else if (of_get_property(np, "ganged-port-switching", NULL))
+		hub->conf_data1 &= ~BIT(0);
+
+	hub->conf_data2 = USB251XB_DEF_CONFIG_DATA_2;
+	if (of_get_property(np, "dynamic-power-switching", NULL))
+		hub->conf_data2 |= BIT(7);
+
+	if (!of_property_read_u32(np, "oc-delay-us", &property_u32)) {
+		if (property_u32 == 100) {
+			/* 100 us*/
+			hub->conf_data2 &= ~BIT(5);
+			hub->conf_data2 &= ~BIT(4);
+		} else if (property_u32 == 4000) {
+			/* 4 ms */
+			hub->conf_data2 &= ~BIT(5);
+			hub->conf_data2 |= BIT(4);
+		} else if (property_u32 == 16000) {
+			/* 16 ms */
+			hub->conf_data2 |= BIT(5);
+			hub->conf_data2 |= BIT(4);
+		} else {
+			/* 8 ms (DEFAULT) */
+			hub->conf_data2 |= BIT(5);
+			hub->conf_data2 &= ~BIT(4);
+		}
+	}
+
+	if (of_get_property(np, "compound-device", NULL))
+		hub->conf_data2 |= BIT(3);
+
+	hub->conf_data3 = USB251XB_DEF_CONFIG_DATA_3;
+	if (of_get_property(np, "port-mapping-mode", NULL))
+		hub->conf_data3 |= BIT(3);
+
+	if (data->led_support && of_get_property(np, "led-usb-mode", NULL))
+		hub->conf_data3 &= ~BIT(1);
+
+	if (of_get_property(np, "string-support", NULL))
+		hub->conf_data3 |= BIT(0);
+
+	hub->non_rem_dev = USB251XB_DEF_NON_REMOVABLE_DEVICES;
+	cproperty_u32 = of_get_property(np, "non-removable-ports", &len);
+	if (cproperty_u32 && (len / sizeof(u32)) > 0) {
+		for (i = 0; i < len / sizeof(u32); i++) {
+			u32 port = be32_to_cpu(cproperty_u32[i]);
+
+			if ((port >= 1) && (port <= data->port_cnt))
+				hub->non_rem_dev |= BIT(port);
+			else
+				dev_warn(dev, "NRD port %u doesn't exist\n",
+					port);
+		}
+	}
+
+	hub->port_disable_sp = USB251XB_DEF_PORT_DISABLE_SELF;
+	cproperty_u32 = of_get_property(np, "sp-disabled-ports", &len);
+	if (cproperty_u32 && (len / sizeof(u32)) > 0) {
+		for (i = 0; i < len / sizeof(u32); i++) {
+			u32 port = be32_to_cpu(cproperty_u32[i]);
+
+			if ((port >= 1) && (port <= data->port_cnt))
+				hub->port_disable_sp |= BIT(port);
+			else
+				dev_warn(dev, "PDS port %u doesn't exist\n",
+					port);
+		}
+	}
+
+	hub->port_disable_bp = USB251XB_DEF_PORT_DISABLE_BUS;
+	cproperty_u32 = of_get_property(np, "bp-disabled-ports", &len);
+	if (cproperty_u32 && (len / sizeof(u32)) > 0) {
+		for (i = 0; i < len / sizeof(u32); i++) {
+			u32 port = be32_to_cpu(cproperty_u32[i]);
+
+			if ((port >= 1) && (port <= data->port_cnt))
+				hub->port_disable_bp |= BIT(port);
+			else
+				dev_warn(dev, "PDB port %u doesn't exist\n",
+					port);
+		}
+	}
+
+	hub->max_power_sp = USB251XB_DEF_MAX_POWER_SELF;
+	if (!of_property_read_u32(np, "sp-max-total-current-microamp",
+	    &property_u32))
+		hub->max_power_sp = min_t(u8, property_u32 / 2000, 50);
+
+	hub->max_power_bp = USB251XB_DEF_MAX_POWER_BUS;
+	if (!of_property_read_u32(np, "bp-max-total-current-microamp",
+	    &property_u32))
+		hub->max_power_bp = min_t(u8, property_u32 / 2000, 255);
+
+	hub->max_current_sp = USB251XB_DEF_MAX_CURRENT_SELF;
+	if (!of_property_read_u32(np, "sp-max-removable-current-microamp",
+	    &property_u32))
+		hub->max_current_sp = min_t(u8, property_u32 / 2000, 50);
+
+	hub->max_current_bp = USB251XB_DEF_MAX_CURRENT_BUS;
+	if (!of_property_read_u32(np, "bp-max-removable-current-microamp",
+	    &property_u32))
+		hub->max_current_bp = min_t(u8, property_u32 / 2000, 255);
+
+	hub->power_on_time = USB251XB_DEF_POWER_ON_TIME;
+	if (!of_property_read_u32(np, "power-on-time-ms", &property_u32))
+		hub->power_on_time = min_t(u8, property_u32 / 2, 255);
+
+	if (of_property_read_u16_array(np, "language-id", &hub->lang_id, 1))
+		hub->lang_id = USB251XB_DEF_LANGUAGE_ID;
+
+	cproperty_char = of_get_property(np, "manufacturer", NULL);
+	strlcpy(str, cproperty_char ? : USB251XB_DEF_MANUFACTURER_STRING,
+		sizeof(str));
+	hub->manufacturer_len = strlen(str) & 0xFF;
+	memset(hub->manufacturer, 0, USB251XB_STRING_BUFSIZE);
+	len = min_t(size_t, USB251XB_STRING_BUFSIZE / 2, strlen(str));
+	len = utf8s_to_utf16s(str, len, UTF16_LITTLE_ENDIAN,
+			      (wchar_t *)hub->manufacturer,
+			      USB251XB_STRING_BUFSIZE);
+
+	cproperty_char = of_get_property(np, "product", NULL);
+	strlcpy(str, cproperty_char ? : data->product_str, sizeof(str));
+	hub->product_len = strlen(str) & 0xFF;
+	memset(hub->product, 0, USB251XB_STRING_BUFSIZE);
+	len = min_t(size_t, USB251XB_STRING_BUFSIZE / 2, strlen(str));
+	len = utf8s_to_utf16s(str, len, UTF16_LITTLE_ENDIAN,
+			      (wchar_t *)hub->product,
+			      USB251XB_STRING_BUFSIZE);
+
+	cproperty_char = of_get_property(np, "serial", NULL);
+	strlcpy(str, cproperty_char ? : USB251XB_DEF_SERIAL_STRING,
+		sizeof(str));
+	hub->serial_len = strlen(str) & 0xFF;
+	memset(hub->serial, 0, USB251XB_STRING_BUFSIZE);
+	len = min_t(size_t, USB251XB_STRING_BUFSIZE / 2, strlen(str));
+	len = utf8s_to_utf16s(str, len, UTF16_LITTLE_ENDIAN,
+			      (wchar_t *)hub->serial,
+			      USB251XB_STRING_BUFSIZE);
+
+	/* The following parameters are currently not exposed to devicetree, but
+	 * may be as soon as needed.
+	 */
+	hub->bat_charge_en = USB251XB_DEF_BATTERY_CHARGING_ENABLE;
+	hub->boost_up = USB251XB_DEF_BOOST_UP;
+	hub->boost_57 = USB251XB_DEF_BOOST_57;
+	hub->boost_14 = USB251XB_DEF_BOOST_14;
+	hub->port_swap = USB251XB_DEF_PORT_SWAP;
+	hub->port_map12 = USB251XB_DEF_PORT_MAP_12;
+	hub->port_map34 = USB251XB_DEF_PORT_MAP_34;
+	hub->port_map56 = USB251XB_DEF_PORT_MAP_56;
+	hub->port_map7  = USB251XB_DEF_PORT_MAP_7;
+
+	return 0;
+}
+
+static const struct of_device_id usb251xb_of_match[] = {
+	{
+		.compatible = "microchip,usb2512b",
+		.data = &usb2512b_data,
+	}, {
+		.compatible = "microchip,usb2512bi",
+		.data = &usb2512bi_data,
+	}, {
+		.compatible = "microchip,usb2513b",
+		.data = &usb2513b_data,
+	}, {
+		.compatible = "microchip,usb2513bi",
+		.data = &usb2513bi_data,
+	}, {
+		.compatible = "microchip,usb2514b",
+		.data = &usb2514b_data,
+	}, {
+		.compatible = "microchip,usb2514bi",
+		.data = &usb2514bi_data,
+	}, {
+		.compatible = "microchip,usb2517",
+		.data = &usb2517_data,
+	}, {
+		.compatible = "microchip,usb2517i",
+		.data = &usb2517i_data,
+	}, {
+		/* sentinel */
+	}
+};
+#else /* CONFIG_OF */
+static int usb251xb_get_ofdata(struct usb251xb *hub,
+			       struct usb251xb_data *data)
+{
+	return 0;
+}
+#endif /* CONFIG_OF */
+
+static int usb251xb_probe(struct usb251xb *hub)
+{
+	struct device_d *dev = hub->dev;
+	struct device_node *np = dev->device_node;
+	const struct of_device_id *of_id = of_match_device(usb251xb_of_match,
+							   dev);
+	int err;
+
+	if (np) {
+		err = usb251xb_get_ofdata(hub,
+					  (struct usb251xb_data *)of_id->data);
+		if (err) {
+			dev_err(dev, "failed to get ofdata: %d\n", err);
+			return err;
+		}
+	}
+
+	err = usb251xb_connect(hub);
+	if (err) {
+		dev_err(dev, "Failed to connect hub (%d)\n", err);
+		return err;
+	}
+
+	dev_info(dev, "Hub probed successfully\n");
+
+	return 0;
+}
+
+static int usb251xb_i2c_probe(struct device_d *dev)
+{
+	struct i2c_client *i2c = to_i2c_client(dev);
+	struct usb251xb *hub;
+
+	hub = xzalloc(sizeof(struct usb251xb));
+
+	i2c_set_clientdata(i2c, hub);
+	hub->dev = &i2c->dev;
+	hub->i2c = i2c;
+
+	return usb251xb_probe(hub);
+}
+
+static const struct platform_device_id usb251xb_id[] = {
+	{ "usb2512b", 0 },
+	{ "usb2512bi", 0 },
+	{ "usb2513b", 0 },
+	{ "usb2513bi", 0 },
+	{ "usb2514b", 0 },
+	{ "usb2514bi", 0 },
+	{ "usb2517", 0 },
+	{ "usb2517i", 0 },
+	{ /* sentinel */ }
+};
+
+static struct driver_d usb251xb_i2c_driver = {
+	.name = DRIVER_NAME,
+	.probe    = usb251xb_i2c_probe,
+	.id_table = usb251xb_id,
+	.of_compatible = DRV_OF_COMPAT(usb251xb_of_match),
+};
+device_i2c_driver(usb251xb_i2c_driver);
-- 
2.20.1


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

  parent reply	other threads:[~2019-02-20  7:30 UTC|newest]

Thread overview: 30+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-02-20  7:29 [PATCH 00/25] i.MX8MQ USB support Andrey Smirnov
2019-02-20  7:29 ` [PATCH 01/25] usb: xhci-hcd: Tabify the file Andrey Smirnov
2019-02-20  7:29 ` [PATCH 02/25] usb: xhci-hcd: Do not zero out DMA coherent memory Andrey Smirnov
2019-02-20  9:29   ` Yann Sionneau
2019-02-20 18:54     ` Andrey Smirnov
2019-02-23 10:16     ` Sam Ravnborg
2019-02-20  7:29 ` [PATCH 03/25] usb: xhci-hcd: Cast ~XHCI_IRQS to u32 Andrey Smirnov
2019-02-20  7:29 ` [PATCH 04/25] usb: xhci-hcd: Make sure to initialize xhci->rings_list Andrey Smirnov
2019-02-20  7:29 ` [PATCH 05/25] usb: xhci-hcd: Drop pointless bitwise or Andrey Smirnov
2019-02-20  7:29 ` [PATCH 06/25] usb: xhci-hcd: Add support for 64-byte context size Andrey Smirnov
2019-02-20  7:29 ` [PATCH 07/25] usb: xhci-hcd: Don't try to DMA sync if buffer is NULL Andrey Smirnov
2019-02-20  7:29 ` [PATCH 08/25] usb: xhci-hcd: Always wait for "Response Data" completion Andrey Smirnov
2019-02-20  7:29 ` [PATCH 09/25] usb: xhci-hcd: Convert xhci_submit_normal() to use dma_map_single() Andrey Smirnov
2019-02-20  7:29 ` [PATCH 10/25] usb: xhci-hcd: Convert xhci_submit_control() " Andrey Smirnov
2019-02-20  7:29 ` [PATCH 11/25] usb: xhci-hcd: Simplify TRB initialization code Andrey Smirnov
2019-02-20  7:29 ` [PATCH 12/25] usb: xhci-hcd: Drop 'dma' field from struct xhci_hcd Andrey Smirnov
2019-02-20  7:29 ` [PATCH 13/25] usb: xhci-hcd: Check usb_pipein(pipe) only once in xhci_submit_normal() Andrey Smirnov
2019-02-20  7:29 ` [PATCH 14/25] usb: xhci-hcd: Initialize TRT flag for xHCI >= 1.0 Andrey Smirnov
2019-02-20  7:29 ` [PATCH 15/25] usb: xhci-hcd: Simplify route string building loop Andrey Smirnov
2019-02-20  7:29 ` [PATCH 16/25] usb: xhci-hcd: Make use of lo_hi_readq/writeq() Andrey Smirnov
2019-02-20  7:29 ` [PATCH 17/25] phy: core: Assume EPROBE_DEFER in of_phy_provider_lookup() Andrey Smirnov
2019-02-20  7:29 ` [PATCH 18/25] phy: Port i.MX8MQ USB PHY driver from Linux Andrey Smirnov
2019-02-20  7:29 ` [PATCH 19/25] clk: Drop separate definitions of clk_put() Andrey Smirnov
2019-02-20  7:29 ` [PATCH 20/25] include/usb: Import USB_SPEED_SUPER_PLUS from Linux Andrey Smirnov
2019-02-20  7:29 ` [PATCH 21/25] clk: Import a subset of clk_bulk API " Andrey Smirnov
2019-02-20  7:29 ` [PATCH 22/25] usb: Import DWC3 USB controller driver " Andrey Smirnov
2019-02-20  7:29 ` [PATCH 23/25] lib: Port basic Linux kernel NLS functions Andrey Smirnov
2019-02-20  7:29 ` Andrey Smirnov [this message]
2019-02-20  7:29 ` [PATCH 25/25] usb: usb251xb: add usb data lane port swap feature Andrey Smirnov
2019-02-22  7:27 ` [PATCH 00/25] i.MX8MQ USB support Sascha Hauer

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190220072930.14300-25-andrew.smirnov@gmail.com \
    --to=andrew.smirnov@gmail.com \
    --cc=barebox@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox