[PATCH v5 12/14] net: dsa: add KSZ9477 switch SPI driver

[Oleksij Rempel <o.rempel@pengutronix.de>]

Add support for Microchip KSZ9477 switch.

With this driver we will be able to use KSZ9477 switch as port
multiplexer.

This driver is partially based on u-boot v2022.04-rc5:
  drivers/net/ksz9477.c
and on the kernel v5.17 code:
  drivers/net/dsa/microchip/ksz9477.c

Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 drivers/net/Kconfig                 |    7 +
 drivers/net/Makefile                |    1 +
 drivers/net/ksz9477.c               |  566 +++++++++
 include/platform_data/ksz9477_reg.h | 1665 +++++++++++++++++++++++++++
 4 files changed, 2239 insertions(+)
 create mode 100644 drivers/net/ksz9477.c
 create mode 100644 include/platform_data/ksz9477_reg.h

diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index ae043d5934..803444cc44 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -306,6 +306,13 @@ menuconfig DSA
 
 if DSA
 
+config DRIVER_NET_KSZ9477
+	bool "KSZ9477 switch driver"
+	depends on SPI
+	help
+	  This option enables support for the Microchip KSZ9477
+	  switch chip.
+
 config DRIVER_NET_SJA1105
 	bool "NXP SJA1105 Ethernet switch family driver"
 	depends on SPI
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 1c979047d9..fa3d4583a0 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -26,6 +26,7 @@ obj-$(CONFIG_DRIVER_NET_FEC_IMX)	+= fec_imx.o
 obj-$(CONFIG_DRIVER_NET_FSL_FMAN)	+= fsl-fman.o
 obj-$(CONFIG_DRIVER_NET_GIANFAR)	+= gianfar.o
 obj-$(CONFIG_DRIVER_NET_KS8851_MLL)	+= ks8851_mll.o
+obj-$(CONFIG_DRIVER_NET_KSZ9477)	+= ksz9477.o
 obj-$(CONFIG_DRIVER_NET_MACB)		+= macb.o
 obj-$(CONFIG_DRIVER_NET_MICREL)		+= ksz8864rmn.o
 obj-$(CONFIG_DRIVER_NET_MPC5200)	+= fec_mpc5200.o
diff --git a/drivers/net/ksz9477.c b/drivers/net/ksz9477.c
new file mode 100644
index 0000000000..779762fad5
--- /dev/null
+++ b/drivers/net/ksz9477.c
@@ -0,0 +1,566 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include <common.h>
+#include <complete.h>
+#include <dsa.h>
+#include <gpiod.h>
+#include <net.h>
+#include <platform_data/ksz9477_reg.h>
+#include <spi/spi.h>
+
+/* SPI frame opcodes */
+#define KS_SPIOP_RD			3
+#define KS_SPIOP_WR			2
+
+#define SPI_ADDR_SHIFT			24
+#define SPI_ADDR_MASK			(BIT(SPI_ADDR_SHIFT) - 1)
+#define SPI_TURNAROUND_SHIFT		5
+
+#define GBIT_SUPPORT			BIT(0)
+#define NEW_XMII			BIT(1)
+#define IS_9893				BIT(2)
+#define KSZ9477_PHY_ERRATA		BIT(3)
+
+struct ksz_switch {
+	struct spi_device *spi;
+	struct dsa_switch ds;
+	struct device_d *dev;
+	int phy_port_cnt;
+	u32 chip_id;
+	u8 features;
+};
+
+static int ksz9477_spi_read_reg(struct spi_device *spi, u32 reg, u8 *val,
+				unsigned int len)
+{
+	u32 txbuf;
+	int ret;
+
+	txbuf = reg & SPI_ADDR_MASK;
+	txbuf |= KS_SPIOP_RD << SPI_ADDR_SHIFT;
+	txbuf <<= SPI_TURNAROUND_SHIFT;
+	txbuf = cpu_to_be32(txbuf);
+
+	ret = spi_write_then_read(spi, &txbuf, 4, val, len);
+
+	return ret;
+}
+
+static int ksz9477_spi_write_reg(struct spi_device *spi, u32 reg, u8 *val,
+				 unsigned int len)
+{
+	u32 txbuf[2];
+
+	txbuf[0] = reg & SPI_ADDR_MASK;
+	txbuf[0] |= (KS_SPIOP_WR << SPI_ADDR_SHIFT);
+	txbuf[0] <<= SPI_TURNAROUND_SHIFT;
+	txbuf[0] = cpu_to_be32(*txbuf);
+	memcpy(&txbuf[1], val, len);
+
+	return spi_write(spi, txbuf, 4 + len);
+}
+
+static int ksz_read8(struct ksz_switch *priv, u32 reg, u8 *val)
+{
+	return ksz9477_spi_read_reg(priv->spi, reg, val, 1);
+}
+
+static int ksz_write8(struct ksz_switch *priv, u32 reg, u8 value)
+{
+	return ksz9477_spi_write_reg(priv->spi, reg, &value, 1);
+}
+
+static int ksz_read16(struct ksz_switch *priv, u32 reg, u16 *val)
+{
+	int ret = ksz9477_spi_read_reg(priv->spi, reg, (u8 *)val, 2);
+
+	if (!ret)
+		*val = be16_to_cpu(*val);
+
+	return ret;
+}
+
+static int ksz_write16(struct ksz_switch *priv, u32 reg, u16 value)
+{
+	struct spi_device *spi = priv->spi;
+
+	value = cpu_to_be16(value);
+	return ksz9477_spi_write_reg(spi, reg, (u8 *)&value, 2);
+}
+
+static int ksz_read32(struct ksz_switch *priv, u32 reg, u32 *val)
+{
+	int ret = ksz9477_spi_read_reg(priv->spi, reg, (u8 *)val, 4);
+
+	if (!ret)
+		*val = be32_to_cpu(*val);
+
+	return ret;
+}
+
+static int ksz_write32(struct ksz_switch *priv, u32 reg, u32 value)
+{
+	struct spi_device *spi = priv->spi;
+
+	value = cpu_to_be32(value);
+	return ksz9477_spi_write_reg(spi, reg, (u8 *)&value, 4);
+}
+
+static void ksz_cfg(struct ksz_switch *priv, u32 addr, u8 bits, bool set)
+{
+	u8 data;
+
+	ksz_read8(priv, addr, &data);
+	if (set)
+		data |= bits;
+	else
+		data &= ~bits;
+	ksz_write8(priv, addr, data);
+}
+
+static int ksz_pread8(struct ksz_switch *priv, int port, int reg, u8 *val)
+{
+	return ksz_read8(priv, PORT_CTRL_ADDR(port, reg), val);
+}
+
+static int ksz_pwrite8(struct ksz_switch *priv, int port, int reg, u8 val)
+{
+	return ksz_write8(priv, PORT_CTRL_ADDR(port, reg), val);
+}
+
+static int ksz_pread16(struct ksz_switch *priv, int port, int reg, u16 *val)
+{
+	return ksz_read16(priv, PORT_CTRL_ADDR(port, reg), val);
+}
+
+static int ksz_pwrite16(struct ksz_switch *priv, int port, int reg, u16 val)
+{
+	return ksz_write16(priv, PORT_CTRL_ADDR(port, reg), val);
+}
+
+static int ksz_pwrite32(struct ksz_switch *priv, int port, int reg, u32 val)
+{
+	return ksz_write32(priv, PORT_CTRL_ADDR(port, reg), val);
+}
+
+static int ksz9477_phy_read16(struct dsa_switch *ds, int addr, int reg)
+{
+	struct device_d *dev = ds->dev;
+	struct ksz_switch *priv = dev_get_priv(dev);
+	u16 val = 0xffff;
+
+	if (addr >= priv->phy_port_cnt)
+		return val;
+
+	ksz_pread16(priv, addr, 0x100 + (reg << 1), &val);
+
+	return val;
+}
+
+static int ksz9477_phy_write16(struct dsa_switch *ds, int addr, int reg,
+			       u16 val)
+{
+	struct device_d *dev = ds->dev;
+	struct ksz_switch *priv = dev_get_priv(dev);
+
+	/* No real PHY after this. */
+	if (addr >= priv->phy_port_cnt)
+		return 0;
+
+	/* No gigabit support.  Do not write to this register. */
+	if (!(priv->features & GBIT_SUPPORT) && reg == MII_CTRL1000)
+		return 0;
+	ksz_pwrite16(priv, addr, 0x100 + (reg << 1), val);
+
+	return 0;
+}
+
+static int ksz9477_switch_detect(struct ksz_switch *priv)
+{
+	u8 id_hi, id_lo;
+	u8 data8;
+	u32 id32;
+	int ret;
+
+	/* read chip id */
+	ret = ksz_read32(priv, REG_CHIP_ID0__1, &id32);
+	if (ret)
+		return ret;
+
+	ret = ksz_read8(priv, REG_GLOBAL_OPTIONS, &data8);
+	if (ret)
+		return ret;
+
+	priv->chip_id = id32;
+
+	priv->phy_port_cnt = 5;
+	priv->features = GBIT_SUPPORT | KSZ9477_PHY_ERRATA;
+
+	id_hi = (u8)(id32 >> 16);
+	id_lo = (u8)(id32 >> 8);
+	if ((id_lo & 0xf) == 3) {
+		/* Chip is from KSZ9893 design. */
+		dev_info(priv->dev, "Found KSZ9893\n");
+		priv->features |= IS_9893;
+		priv->features &= ~KSZ9477_PHY_ERRATA;
+
+		/* Chip does not support gigabit. */
+		if (data8 & SW_QW_ABLE)
+			priv->features &= ~GBIT_SUPPORT;
+		priv->phy_port_cnt = 2;
+	} else {
+		dev_info(priv->dev, "Found KSZ9477 or compatible\n");
+		/* Chip uses new XMII register definitions. */
+		priv->features |= NEW_XMII;
+
+		/* Chip does not support gigabit. */
+		if (!(data8 & SW_GIGABIT_ABLE))
+			priv->features &= ~GBIT_SUPPORT;
+	}
+
+	return 0;
+}
+
+static int ksz_reset_switch(struct ksz_switch *priv)
+{
+	u8 data8;
+	u16 data16;
+	u32 data32;
+
+	/* reset switch */
+	ksz_cfg(priv, REG_SW_OPERATION, SW_RESET, true);
+
+	/* turn off SPI DO Edge select */
+	ksz_read8(priv, REG_SW_GLOBAL_SERIAL_CTRL_0, &data8);
+	data8 &= ~SPI_AUTO_EDGE_DETECTION;
+	ksz_write8(priv, REG_SW_GLOBAL_SERIAL_CTRL_0, data8);
+
+	/* default configuration */
+	ksz_read8(priv, REG_SW_LUE_CTRL_1, &data8);
+	data8 = SW_AGING_ENABLE | SW_LINK_AUTO_AGING |
+	      SW_SRC_ADDR_FILTER | SW_FLUSH_STP_TABLE | SW_FLUSH_MSTP_TABLE;
+	ksz_write8(priv, REG_SW_LUE_CTRL_1, data8);
+
+	/* disable interrupts */
+	ksz_write32(priv, REG_SW_INT_MASK__4, SWITCH_INT_MASK);
+	ksz_write32(priv, REG_SW_PORT_INT_MASK__4, 0x7F);
+	ksz_read32(priv, REG_SW_PORT_INT_STATUS__4, &data32);
+
+	/* set broadcast storm protection 10% rate */
+	ksz_read16(priv, REG_SW_MAC_CTRL_2, &data16);
+	data16 &= ~BROADCAST_STORM_RATE;
+	data16 |= (BROADCAST_STORM_VALUE * BROADCAST_STORM_PROT_RATE) / 100;
+	ksz_write16(priv, REG_SW_MAC_CTRL_2, data16);
+
+	return 0;
+}
+
+static void ksz9477_cfg_port_member(struct ksz_switch *priv, int port,
+				    u8 member)
+{
+	ksz_pwrite32(priv, port, REG_PORT_VLAN_MEMBERSHIP__4, member);
+}
+
+static void ksz9477_port_mmd_write(struct ksz_switch *priv, int port,
+				   u8 dev_addr, u16 reg_addr, u16 val)
+{
+	ksz_pwrite16(priv, port, REG_PORT_PHY_MMD_SETUP,
+		     MMD_SETUP(PORT_MMD_OP_INDEX, dev_addr));
+	ksz_pwrite16(priv, port, REG_PORT_PHY_MMD_INDEX_DATA, reg_addr);
+	ksz_pwrite16(priv, port, REG_PORT_PHY_MMD_SETUP,
+		     MMD_SETUP(PORT_MMD_OP_DATA_NO_INCR, dev_addr));
+	ksz_pwrite16(priv, port, REG_PORT_PHY_MMD_INDEX_DATA, val);
+}
+
+static void ksz9477_phy_errata_setup(struct ksz_switch *priv, int port)
+{
+	/* Apply PHY settings to address errata listed in
+	 * KSZ9477, KSZ9897, KSZ9896, KSZ9567, KSZ8565
+	 * Silicon Errata and Data Sheet Clarification documents:
+	 *
+	 * Register settings are needed to improve PHY receive performance
+	 */
+	ksz9477_port_mmd_write(priv, port, 0x01, 0x6f, 0xdd0b);
+	ksz9477_port_mmd_write(priv, port, 0x01, 0x8f, 0x6032);
+	ksz9477_port_mmd_write(priv, port, 0x01, 0x9d, 0x248c);
+	ksz9477_port_mmd_write(priv, port, 0x01, 0x75, 0x0060);
+	ksz9477_port_mmd_write(priv, port, 0x01, 0xd3, 0x7777);
+	ksz9477_port_mmd_write(priv, port, 0x1c, 0x06, 0x3008);
+	ksz9477_port_mmd_write(priv, port, 0x1c, 0x08, 0x2001);
+
+	/* Transmit waveform amplitude can be improved
+	 * (1000BASE-T, 100BASE-TX, 10BASE-Te)
+	 */
+	ksz9477_port_mmd_write(priv, port, 0x1c, 0x04, 0x00d0);
+
+	/* Energy Efficient Ethernet (EEE) feature select must
+	 * be manually disabled (except on KSZ8565 which is 100Mbit)
+	 */
+	if (priv->features & GBIT_SUPPORT)
+		ksz9477_port_mmd_write(priv, port, 0x07, 0x3c, 0x0000);
+
+	/* Register settings are required to meet data sheet
+	 * supply current specifications
+	 */
+	ksz9477_port_mmd_write(priv, port, 0x1c, 0x13, 0x6eff);
+	ksz9477_port_mmd_write(priv, port, 0x1c, 0x14, 0xe6ff);
+	ksz9477_port_mmd_write(priv, port, 0x1c, 0x15, 0x6eff);
+	ksz9477_port_mmd_write(priv, port, 0x1c, 0x16, 0xe6ff);
+	ksz9477_port_mmd_write(priv, port, 0x1c, 0x17, 0x00ff);
+	ksz9477_port_mmd_write(priv, port, 0x1c, 0x18, 0x43ff);
+	ksz9477_port_mmd_write(priv, port, 0x1c, 0x19, 0xc3ff);
+	ksz9477_port_mmd_write(priv, port, 0x1c, 0x1a, 0x6fff);
+	ksz9477_port_mmd_write(priv, port, 0x1c, 0x1b, 0x07ff);
+	ksz9477_port_mmd_write(priv, port, 0x1c, 0x1c, 0x0fff);
+	ksz9477_port_mmd_write(priv, port, 0x1c, 0x1d, 0xe7ff);
+	ksz9477_port_mmd_write(priv, port, 0x1c, 0x1e, 0xefff);
+	ksz9477_port_mmd_write(priv, port, 0x1c, 0x20, 0xeeee);
+}
+
+static void ksz9477_set_xmii(struct ksz_switch *priv, int mode, u8 *data)
+{
+	u8 xmii;
+
+	if (priv->features & NEW_XMII) {
+		switch (mode) {
+		case 0:
+			xmii = PORT_MII_SEL;
+			break;
+		case 1:
+			xmii = PORT_RMII_SEL;
+			break;
+		case 2:
+			xmii = PORT_GMII_SEL;
+			break;
+		default:
+			xmii = PORT_RGMII_SEL;
+			break;
+		}
+	} else {
+		switch (mode) {
+		case 0:
+			xmii = PORT_MII_SEL_S1;
+			break;
+		case 1:
+			xmii = PORT_RMII_SEL_S1;
+			break;
+		case 2:
+			xmii = PORT_GMII_SEL_S1;
+			break;
+		default:
+			xmii = PORT_RGMII_SEL_S1;
+			break;
+		}
+	}
+	*data &= ~PORT_MII_SEL_M;
+	*data |= xmii;
+}
+
+static void ksz9477_set_gbit(struct ksz_switch *priv, bool gbit, u8 *data)
+{
+	if (priv->features & NEW_XMII) {
+		if (gbit)
+			*data &= ~PORT_MII_NOT_1GBIT;
+		else
+			*data |= PORT_MII_NOT_1GBIT;
+	} else {
+		if (gbit)
+			*data |= PORT_MII_1000MBIT_S1;
+		else
+			*data &= ~PORT_MII_1000MBIT_S1;
+	}
+}
+
+static int ksz_port_setup(struct ksz_switch *priv, int port,
+			  phy_interface_t interface)
+{
+	u8 data8, member;
+
+	if (port != priv->ds.cpu_port) {
+		ksz_pwrite8(priv, port, REG_PORT_CTRL_0, 0);
+		member = BIT(priv->ds.cpu_port);
+		ksz9477_cfg_port_member(priv, port, member);
+
+		member = dsa_user_ports(&priv->ds);
+		ksz9477_cfg_port_member(priv, priv->ds.cpu_port, member);
+
+		if (priv->features & KSZ9477_PHY_ERRATA)
+			ksz9477_phy_errata_setup(priv, port);
+
+		ksz_pwrite16(priv, port, 0x100 + (MII_BMCR << 1),
+			     BMCR_ANENABLE | BMCR_ANRESTART | BMCR_RESET);
+	} else {
+		ksz_pwrite8(priv, port, REG_PORT_CTRL_0, PORT_TAIL_TAG_ENABLE);
+		/* cpu port: configure MAC interface mode */
+		ksz_pread8(priv, port, REG_PORT_XMII_CTRL_1, &data8);
+		switch (interface) {
+		case PHY_INTERFACE_MODE_MII:
+			ksz9477_set_xmii(priv, 0, &data8);
+			ksz9477_set_gbit(priv, false, &data8);
+			break;
+		case PHY_INTERFACE_MODE_RMII:
+			ksz9477_set_xmii(priv, 1, &data8);
+			ksz9477_set_gbit(priv, false, &data8);
+			break;
+		case PHY_INTERFACE_MODE_GMII:
+			ksz9477_set_xmii(priv, 2, &data8);
+			ksz9477_set_gbit(priv, true, &data8);
+			break;
+		default:
+			ksz9477_set_xmii(priv, 3, &data8);
+			ksz9477_set_gbit(priv, true, &data8);
+			data8 &= ~PORT_RGMII_ID_IG_ENABLE;
+			data8 &= ~PORT_RGMII_ID_EG_ENABLE;
+			if (interface == PHY_INTERFACE_MODE_RGMII_ID ||
+			    interface == PHY_INTERFACE_MODE_RGMII_RXID)
+				data8 |= PORT_RGMII_ID_IG_ENABLE;
+			if (interface == PHY_INTERFACE_MODE_RGMII_ID ||
+			    interface == PHY_INTERFACE_MODE_RGMII_TXID)
+				data8 |= PORT_RGMII_ID_EG_ENABLE;
+			/* On KSZ9893, disable RGMII in-band status support */
+			if (priv->features & IS_9893)
+				data8 &= ~PORT_MII_MAC_MODE;
+			break;
+		}
+		ksz_pwrite8(priv, port, REG_PORT_XMII_CTRL_1, data8);
+	}
+
+	return 0;
+}
+
+static int ksz_port_enable(struct dsa_port *dp, int port,
+			   struct phy_device *phy)
+{
+	struct device_d *dev = dp->ds->dev;
+	struct ksz_switch *priv = dev_get_priv(dev);
+	u8 data8;
+	int ret;
+
+	/* setup this port */
+	ret = ksz_port_setup(priv, port, phy->interface);
+	if (ret) {
+		dev_err(dev, "port setup failed: %d\n", ret);
+		return ret;
+	}
+
+	/* enable port forwarding for this port */
+	ksz_pread8(priv, port, REG_PORT_LUE_MSTP_STATE, &data8);
+	data8 &= ~PORT_LEARN_DISABLE;
+	data8 |= (PORT_TX_ENABLE | PORT_RX_ENABLE);
+	ksz_pwrite8(priv, port, REG_PORT_LUE_MSTP_STATE, data8);
+
+	/* if cpu master we are done */
+	if (port == dp->ds->cpu_port)
+		return 0;
+
+	/* start switch */
+	ksz_read8(priv, REG_SW_OPERATION, &data8);
+	data8 |= SW_START;
+	ksz_write8(priv, REG_SW_OPERATION, data8);
+
+	return 0;
+}
+
+static int ksz_xmit(struct dsa_port *dp, int port, void *packet, int length)
+{
+	u16 *tag = packet + length - dp->ds->needed_tx_tailroom;
+
+	*tag = cpu_to_be16(BIT(dp->index));
+
+	return 0;
+}
+
+static int ksz_recv(struct dsa_switch *ds, int *port, void *packet, int length)
+{
+	u8 *tag = packet + length - ds->needed_rx_tailroom;
+
+	*port = *tag & 7;
+
+	return 0;
+};
+
+static const struct dsa_ops ksz_dsa_ops = {
+	.port_enable = ksz_port_enable,
+	.xmit = ksz_xmit,
+	.rcv = ksz_recv,
+	.phy_read = ksz9477_phy_read16,
+	.phy_write = ksz9477_phy_write16,
+};
+
+static int ksz_default_setup(struct ksz_switch *priv)
+{
+	int i;
+
+	for (i = 0; i < priv->ds.num_ports; i++) {
+		/* isolate all ports by default */
+		ksz9477_cfg_port_member(priv, i, 0);
+		/* and suspend ports with integrated PHYs */
+		if (i < priv->phy_port_cnt)
+			ksz_pwrite16(priv, i, 0x100 + (MII_BMCR << 1),
+				     BMCR_PDOWN);
+	}
+
+	return 0;
+}
+
+static int microchip_switch_probe(struct device_d *dev)
+{
+	struct ksz_switch *priv;
+	int ret = 0, gpio;
+	struct dsa_switch *ds;
+
+	priv = xzalloc(sizeof(*priv));
+
+	dev->priv = priv;
+	priv->dev = dev;
+
+	priv->spi = (struct spi_device *)dev->type_data;
+	priv->spi->mode = SPI_MODE_0;
+	priv->spi->bits_per_word = 8;
+
+	gpio = gpiod_get(dev, "reset", GPIOF_OUT_INIT_ACTIVE);
+	if (gpio_is_valid(gpio)) {
+		mdelay(1);
+		gpio_set_active(gpio, false);
+	}
+
+	ksz_reset_switch(dev->priv);
+
+	ret = ksz9477_switch_detect(dev->priv);
+	if (ret) {
+		dev_err(&priv->spi->dev, "error detecting KSZ9477: %s\n",
+			strerror(-ret));
+		return -ENODEV;
+	}
+
+	dev_info(dev, "chip id: 0x%08x\n", priv->chip_id);
+
+	ds = &priv->ds;
+	ds->dev = dev;
+	ds->num_ports = 7;
+	ds->ops = &ksz_dsa_ops;
+	ds->needed_rx_tailroom = 1;
+	ds->needed_tx_tailroom = 2;
+	if (priv->phy_port_cnt == 5)
+		ds->phys_mii_mask = 0x1f;
+	else
+		ds->phys_mii_mask = 0x03;
+
+	ksz_default_setup(priv);
+
+	return dsa_register_switch(ds);
+}
+
+static const struct of_device_id microchip_switch_dt_ids[] = {
+	{ .compatible = "microchip,ksz9477" },
+	{ .compatible = "microchip,ksz9563" },
+	{ }
+};
+
+static struct driver_d microchip_switch_driver = {
+	.name		= "ksz9477",
+	.probe		= microchip_switch_probe,
+	.of_compatible	= DRV_OF_COMPAT(microchip_switch_dt_ids),
+};
+
+device_spi_driver(microchip_switch_driver);
diff --git a/include/platform_data/ksz9477_reg.h b/include/platform_data/ksz9477_reg.h
new file mode 100644
index 0000000000..2938e892b6
--- /dev/null
+++ b/include/platform_data/ksz9477_reg.h
@@ -0,0 +1,1665 @@
+/* SPDX-License-Identifier: GPL-2.0
+ *
+ * Microchip KSZ9477 register definitions
+ *
+ * Copyright (C) 2017-2018 Microchip Technology Inc.
+ */
+
+#ifndef __KSZ9477_REGS_H
+#define __KSZ9477_REGS_H
+
+#define KS_PRIO_M			0x7
+#define KS_PRIO_S			4
+
+/* 0 - Operation */
+#define REG_CHIP_ID0__1			0x0000
+
+#define REG_CHIP_ID1__1			0x0001
+
+#define FAMILY_ID			0x95
+#define FAMILY_ID_94			0x94
+#define FAMILY_ID_95			0x95
+#define FAMILY_ID_85			0x85
+#define FAMILY_ID_98			0x98
+#define FAMILY_ID_88			0x88
+
+#define REG_CHIP_ID2__1			0x0002
+
+#define CHIP_ID_63			0x63
+#define CHIP_ID_66			0x66
+#define CHIP_ID_67			0x67
+#define CHIP_ID_77			0x77
+#define CHIP_ID_93			0x93
+#define CHIP_ID_96			0x96
+#define CHIP_ID_97			0x97
+
+#define REG_CHIP_ID3__1			0x0003
+
+#define SWITCH_REVISION_M		0x0F
+#define SWITCH_REVISION_S		4
+#define SWITCH_RESET			0x01
+
+#define REG_SW_PME_CTRL			0x0006
+
+#define PME_ENABLE			BIT(1)
+#define PME_POLARITY			BIT(0)
+
+#define REG_GLOBAL_OPTIONS		0x000F
+
+#define SW_GIGABIT_ABLE			BIT(6)
+#define SW_REDUNDANCY_ABLE		BIT(5)
+#define SW_AVB_ABLE			BIT(4)
+#define SW_9567_RL_5_2			0xC
+#define SW_9477_SL_5_2			0xD
+
+#define SW_9896_GL_5_1			0xB
+#define SW_9896_RL_5_1			0x8
+#define SW_9896_SL_5_1			0x9
+
+#define SW_9895_GL_4_1			0x7
+#define SW_9895_RL_4_1			0x4
+#define SW_9895_SL_4_1			0x5
+
+#define SW_9896_RL_4_2			0x6
+
+#define SW_9893_RL_2_1			0x0
+#define SW_9893_SL_2_1			0x1
+#define SW_9893_GL_2_1			0x3
+
+#define SW_QW_ABLE			BIT(5)
+#define SW_9893_RN_2_1			0xC
+
+#define REG_SW_INT_STATUS__4		0x0010
+#define REG_SW_INT_MASK__4		0x0014
+
+#define LUE_INT				BIT(31)
+#define TRIG_TS_INT			BIT(30)
+#define APB_TIMEOUT_INT			BIT(29)
+
+#define SWITCH_INT_MASK			(TRIG_TS_INT | APB_TIMEOUT_INT)
+
+#define REG_SW_PORT_INT_STATUS__4	0x0018
+#define REG_SW_PORT_INT_MASK__4		0x001C
+#define REG_SW_PHY_INT_STATUS		0x0020
+#define REG_SW_PHY_INT_ENABLE		0x0024
+
+/* 1 - Global */
+#define REG_SW_GLOBAL_SERIAL_CTRL_0	0x0100
+#define SW_SPARE_REG_2			BIT(7)
+#define SW_SPARE_REG_1			BIT(6)
+#define SW_SPARE_REG_0			BIT(5)
+#define SW_BIG_ENDIAN			BIT(4)
+#define SPI_AUTO_EDGE_DETECTION		BIT(1)
+#define SPI_CLOCK_OUT_RISING_EDGE	BIT(0)
+
+#define REG_SW_GLOBAL_OUTPUT_CTRL__1	0x0103
+#define SW_ENABLE_REFCLKO		BIT(1)
+#define SW_REFCLKO_IS_125MHZ		BIT(0)
+
+#define REG_SW_IBA__4			0x0104
+
+#define SW_IBA_ENABLE			BIT(31)
+#define SW_IBA_DA_MATCH			BIT(30)
+#define SW_IBA_INIT			BIT(29)
+#define SW_IBA_QID_M			0xF
+#define SW_IBA_QID_S			22
+#define SW_IBA_PORT_M			0x2F
+#define SW_IBA_PORT_S			16
+#define SW_IBA_FRAME_TPID_M		0xFFFF
+
+#define REG_SW_APB_TIMEOUT_ADDR__4	0x0108
+
+#define APB_TIMEOUT_ACKNOWLEDGE		BIT(31)
+
+#define REG_SW_IBA_SYNC__1		0x010C
+
+#define REG_SW_IO_STRENGTH__1		0x010D
+#define SW_DRIVE_STRENGTH_M		0x7
+#define SW_DRIVE_STRENGTH_2MA		0
+#define SW_DRIVE_STRENGTH_4MA		1
+#define SW_DRIVE_STRENGTH_8MA		2
+#define SW_DRIVE_STRENGTH_12MA		3
+#define SW_DRIVE_STRENGTH_16MA		4
+#define SW_DRIVE_STRENGTH_20MA		5
+#define SW_DRIVE_STRENGTH_24MA		6
+#define SW_DRIVE_STRENGTH_28MA		7
+#define SW_HI_SPEED_DRIVE_STRENGTH_S	4
+#define SW_LO_SPEED_DRIVE_STRENGTH_S	0
+
+#define REG_SW_IBA_STATUS__4		0x0110
+
+#define SW_IBA_REQ			BIT(31)
+#define SW_IBA_RESP			BIT(30)
+#define SW_IBA_DA_MISMATCH		BIT(14)
+#define SW_IBA_FMT_MISMATCH		BIT(13)
+#define SW_IBA_CODE_ERROR		BIT(12)
+#define SW_IBA_CMD_ERROR		BIT(11)
+#define SW_IBA_CMD_LOC_M		(BIT(6) - 1)
+
+#define REG_SW_IBA_STATES__4		0x0114
+
+#define SW_IBA_BUF_STATE_S		30
+#define SW_IBA_CMD_STATE_S		28
+#define SW_IBA_RESP_STATE_S		26
+#define SW_IBA_STATE_M			0x3
+#define SW_IBA_PACKET_SIZE_M		0x7F
+#define SW_IBA_PACKET_SIZE_S		16
+#define SW_IBA_FMT_ID_M			0xFFFF
+
+#define REG_SW_IBA_RESULT__4		0x0118
+
+#define SW_IBA_SIZE_S			24
+
+#define SW_IBA_RETRY_CNT_M		(BIT(5) - 1)
+
+/* 2 - PHY */
+#define REG_SW_POWER_MANAGEMENT_CTRL	0x0201
+
+#define SW_PLL_POWER_DOWN		BIT(5)
+#define SW_POWER_DOWN_MODE		0x3
+#define SW_ENERGY_DETECTION		1
+#define SW_SOFT_POWER_DOWN		2
+#define SW_POWER_SAVING			3
+
+/* 3 - Operation Control */
+#define REG_SW_OPERATION		0x0300
+
+#define SW_DOUBLE_TAG			BIT(7)
+#define SW_RESET			BIT(1)
+#define SW_START			BIT(0)
+
+#define REG_SW_MAC_ADDR_0		0x0302
+#define REG_SW_MAC_ADDR_1		0x0303
+#define REG_SW_MAC_ADDR_2		0x0304
+#define REG_SW_MAC_ADDR_3		0x0305
+#define REG_SW_MAC_ADDR_4		0x0306
+#define REG_SW_MAC_ADDR_5		0x0307
+
+#define REG_SW_MTU__2			0x0308
+
+#define REG_SW_ISP_TPID__2		0x030A
+
+#define REG_SW_HSR_TPID__2		0x030C
+
+#define REG_AVB_STRATEGY__2		0x030E
+
+#define SW_SHAPING_CREDIT_ACCT		BIT(1)
+#define SW_POLICING_CREDIT_ACCT		BIT(0)
+
+#define REG_SW_LUE_CTRL_0		0x0310
+
+#define SW_VLAN_ENABLE			BIT(7)
+#define SW_DROP_INVALID_VID		BIT(6)
+#define SW_AGE_CNT_M			0x7
+#define SW_AGE_CNT_S			3
+#define SW_RESV_MCAST_ENABLE		BIT(2)
+#define SW_HASH_OPTION_M		0x03
+#define SW_HASH_OPTION_CRC		1
+#define SW_HASH_OPTION_XOR		2
+#define SW_HASH_OPTION_DIRECT		3
+
+#define REG_SW_LUE_CTRL_1		0x0311
+
+#define UNICAST_LEARN_DISABLE		BIT(7)
+#define SW_SRC_ADDR_FILTER		BIT(6)
+#define SW_FLUSH_STP_TABLE		BIT(5)
+#define SW_FLUSH_MSTP_TABLE		BIT(4)
+#define SW_FWD_MCAST_SRC_ADDR		BIT(3)
+#define SW_AGING_ENABLE			BIT(2)
+#define SW_FAST_AGING			BIT(1)
+#define SW_LINK_AUTO_AGING		BIT(0)
+
+#define REG_SW_LUE_CTRL_2		0x0312
+
+#define SW_TRAP_DOUBLE_TAG		BIT(6)
+#define SW_EGRESS_VLAN_FILTER_DYN	BIT(5)
+#define SW_EGRESS_VLAN_FILTER_STA	BIT(4)
+#define SW_FLUSH_OPTION_M		0x3
+#define SW_FLUSH_OPTION_S		2
+#define SW_FLUSH_OPTION_DYN_MAC		1
+#define SW_FLUSH_OPTION_STA_MAC		2
+#define SW_FLUSH_OPTION_BOTH		3
+#define SW_PRIO_M			0x3
+#define SW_PRIO_DA			0
+#define SW_PRIO_SA			1
+#define SW_PRIO_HIGHEST_DA_SA		2
+#define SW_PRIO_LOWEST_DA_SA		3
+
+#define REG_SW_LUE_CTRL_3		0x0313
+
+#define REG_SW_LUE_INT_STATUS		0x0314
+#define REG_SW_LUE_INT_ENABLE		0x0315
+
+#define LEARN_FAIL_INT			BIT(2)
+#define ALMOST_FULL_INT			BIT(1)
+#define WRITE_FAIL_INT			BIT(0)
+
+#define REG_SW_LUE_INDEX_0__2		0x0316
+
+#define ENTRY_INDEX_M			0x0FFF
+
+#define REG_SW_LUE_INDEX_1__2		0x0318
+
+#define FAIL_INDEX_M			0x03FF
+
+#define REG_SW_LUE_INDEX_2__2		0x031A
+
+#define REG_SW_LUE_UNK_UCAST_CTRL__4	0x0320
+
+#define SW_UNK_UCAST_ENABLE		BIT(31)
+
+#define REG_SW_LUE_UNK_MCAST_CTRL__4	0x0324
+
+#define SW_UNK_MCAST_ENABLE		BIT(31)
+
+#define REG_SW_LUE_UNK_VID_CTRL__4	0x0328
+
+#define SW_UNK_VID_ENABLE		BIT(31)
+
+#define REG_SW_MAC_CTRL_0		0x0330
+
+#define SW_NEW_BACKOFF			BIT(7)
+#define SW_CHECK_LENGTH			BIT(3)
+#define SW_PAUSE_UNH_MODE		BIT(1)
+#define SW_AGGR_BACKOFF			BIT(0)
+
+#define REG_SW_MAC_CTRL_1		0x0331
+
+#define MULTICAST_STORM_DISABLE		BIT(6)
+#define SW_BACK_PRESSURE		BIT(5)
+#define FAIR_FLOW_CTRL			BIT(4)
+#define NO_EXC_COLLISION_DROP		BIT(3)
+#define SW_JUMBO_PACKET			BIT(2)
+#define SW_LEGAL_PACKET_DISABLE		BIT(1)
+#define SW_PASS_SHORT_FRAME		BIT(0)
+
+#define REG_SW_MAC_CTRL_2		0x0332
+
+#define SW_REPLACE_VID			BIT(3)
+#define BROADCAST_STORM_RATE_HI		0x07
+
+#define REG_SW_MAC_CTRL_3		0x0333
+
+#define BROADCAST_STORM_RATE_LO		0xFF
+#define BROADCAST_STORM_RATE		0x07FF
+
+#define REG_SW_MAC_CTRL_4		0x0334
+
+#define SW_PASS_PAUSE			BIT(3)
+
+#define REG_SW_MAC_CTRL_5		0x0335
+
+#define SW_OUT_RATE_LIMIT_QUEUE_BASED	BIT(3)
+
+#define REG_SW_MAC_CTRL_6		0x0336
+
+#define SW_MIB_COUNTER_FLUSH		BIT(7)
+#define SW_MIB_COUNTER_FREEZE		BIT(6)
+
+#define REG_SW_MAC_802_1P_MAP_0		0x0338
+#define REG_SW_MAC_802_1P_MAP_1		0x0339
+#define REG_SW_MAC_802_1P_MAP_2		0x033A
+#define REG_SW_MAC_802_1P_MAP_3		0x033B
+
+#define SW_802_1P_MAP_M			KS_PRIO_M
+#define SW_802_1P_MAP_S			KS_PRIO_S
+
+#define REG_SW_MAC_ISP_CTRL		0x033C
+
+#define REG_SW_MAC_TOS_CTRL		0x033E
+
+#define SW_TOS_DSCP_REMARK		BIT(1)
+#define SW_TOS_DSCP_REMAP		BIT(0)
+
+#define REG_SW_MAC_TOS_PRIO_0		0x0340
+#define REG_SW_MAC_TOS_PRIO_1		0x0341
+#define REG_SW_MAC_TOS_PRIO_2		0x0342
+#define REG_SW_MAC_TOS_PRIO_3		0x0343
+#define REG_SW_MAC_TOS_PRIO_4		0x0344
+#define REG_SW_MAC_TOS_PRIO_5		0x0345
+#define REG_SW_MAC_TOS_PRIO_6		0x0346
+#define REG_SW_MAC_TOS_PRIO_7		0x0347
+#define REG_SW_MAC_TOS_PRIO_8		0x0348
+#define REG_SW_MAC_TOS_PRIO_9		0x0349
+#define REG_SW_MAC_TOS_PRIO_10		0x034A
+#define REG_SW_MAC_TOS_PRIO_11		0x034B
+#define REG_SW_MAC_TOS_PRIO_12		0x034C
+#define REG_SW_MAC_TOS_PRIO_13		0x034D
+#define REG_SW_MAC_TOS_PRIO_14		0x034E
+#define REG_SW_MAC_TOS_PRIO_15		0x034F
+#define REG_SW_MAC_TOS_PRIO_16		0x0350
+#define REG_SW_MAC_TOS_PRIO_17		0x0351
+#define REG_SW_MAC_TOS_PRIO_18		0x0352
+#define REG_SW_MAC_TOS_PRIO_19		0x0353
+#define REG_SW_MAC_TOS_PRIO_20		0x0354
+#define REG_SW_MAC_TOS_PRIO_21		0x0355
+#define REG_SW_MAC_TOS_PRIO_22		0x0356
+#define REG_SW_MAC_TOS_PRIO_23		0x0357
+#define REG_SW_MAC_TOS_PRIO_24		0x0358
+#define REG_SW_MAC_TOS_PRIO_25		0x0359
+#define REG_SW_MAC_TOS_PRIO_26		0x035A
+#define REG_SW_MAC_TOS_PRIO_27		0x035B
+#define REG_SW_MAC_TOS_PRIO_28		0x035C
+#define REG_SW_MAC_TOS_PRIO_29		0x035D
+#define REG_SW_MAC_TOS_PRIO_30		0x035E
+#define REG_SW_MAC_TOS_PRIO_31		0x035F
+
+#define REG_SW_MRI_CTRL_0		0x0370
+
+#define SW_IGMP_SNOOP			BIT(6)
+#define SW_IPV6_MLD_OPTION		BIT(3)
+#define SW_IPV6_MLD_SNOOP		BIT(2)
+#define SW_MIRROR_RX_TX			BIT(0)
+
+#define REG_SW_CLASS_D_IP_CTRL__4	0x0374
+
+#define SW_CLASS_D_IP_ENABLE		BIT(31)
+
+#define REG_SW_MRI_CTRL_8		0x0378
+
+#define SW_NO_COLOR_S			6
+#define SW_RED_COLOR_S			4
+#define SW_YELLOW_COLOR_S		2
+#define SW_GREEN_COLOR_S		0
+#define SW_COLOR_M			0x3
+
+#define REG_SW_QM_CTRL__4		0x0390
+
+#define PRIO_SCHEME_SELECT_M		KS_PRIO_M
+#define PRIO_SCHEME_SELECT_S		6
+#define PRIO_MAP_3_HI			0
+#define PRIO_MAP_2_HI			2
+#define PRIO_MAP_0_LO			3
+#define UNICAST_VLAN_BOUNDARY		BIT(1)
+
+#define REG_SW_EEE_QM_CTRL__2		0x03C0
+
+#define REG_SW_EEE_TXQ_WAIT_TIME__2	0x03C2
+
+/* 4 - */
+#define REG_SW_VLAN_ENTRY__4		0x0400
+
+#define VLAN_VALID			BIT(31)
+#define VLAN_FORWARD_OPTION		BIT(27)
+#define VLAN_PRIO_M			KS_PRIO_M
+#define VLAN_PRIO_S			24
+#define VLAN_MSTP_M			0x7
+#define VLAN_MSTP_S			12
+#define VLAN_FID_M			0x7F
+
+#define REG_SW_VLAN_ENTRY_UNTAG__4	0x0404
+#define REG_SW_VLAN_ENTRY_PORTS__4	0x0408
+
+#define REG_SW_VLAN_ENTRY_INDEX__2	0x040C
+
+#define VLAN_INDEX_M			0x0FFF
+
+#define REG_SW_VLAN_CTRL		0x040E
+
+#define VLAN_START			BIT(7)
+#define VLAN_ACTION			0x3
+#define VLAN_WRITE			1
+#define VLAN_READ			2
+#define VLAN_CLEAR			3
+
+#define REG_SW_ALU_INDEX_0		0x0410
+
+#define ALU_FID_INDEX_S			16
+#define ALU_MAC_ADDR_HI			0xFFFF
+
+#define REG_SW_ALU_INDEX_1		0x0414
+
+#define ALU_DIRECT_INDEX_M		(BIT(12) - 1)
+
+#define REG_SW_ALU_CTRL__4		0x0418
+
+#define ALU_VALID_CNT_M			(BIT(14) - 1)
+#define ALU_VALID_CNT_S			16
+#define ALU_START			BIT(7)
+#define ALU_VALID			BIT(6)
+#define ALU_DIRECT			BIT(2)
+#define ALU_ACTION			0x3
+#define ALU_WRITE			1
+#define ALU_READ			2
+#define ALU_SEARCH			3
+
+#define REG_SW_ALU_STAT_CTRL__4		0x041C
+
+#define ALU_STAT_INDEX_M		(BIT(4) - 1)
+#define ALU_STAT_INDEX_S		16
+#define ALU_RESV_MCAST_INDEX_M		(BIT(6) - 1)
+#define ALU_STAT_START			BIT(7)
+#define ALU_RESV_MCAST_ADDR		BIT(1)
+#define ALU_STAT_READ			BIT(0)
+
+#define REG_SW_ALU_VAL_A		0x0420
+
+#define ALU_V_STATIC_VALID		BIT(31)
+#define ALU_V_SRC_FILTER		BIT(30)
+#define ALU_V_DST_FILTER		BIT(29)
+#define ALU_V_PRIO_AGE_CNT_M		(BIT(3) - 1)
+#define ALU_V_PRIO_AGE_CNT_S		26
+#define ALU_V_MSTP_M			0x7
+
+#define REG_SW_ALU_VAL_B		0x0424
+
+#define ALU_V_OVERRIDE			BIT(31)
+#define ALU_V_USE_FID			BIT(30)
+#define ALU_V_PORT_MAP			(BIT(24) - 1)
+
+#define REG_SW_ALU_VAL_C		0x0428
+
+#define ALU_V_FID_M			(BIT(16) - 1)
+#define ALU_V_FID_S			16
+#define ALU_V_MAC_ADDR_HI		0xFFFF
+
+#define REG_SW_ALU_VAL_D		0x042C
+
+#define REG_HSR_ALU_INDEX_0		0x0440
+
+#define REG_HSR_ALU_INDEX_1		0x0444
+
+#define HSR_DST_MAC_INDEX_LO_S		16
+#define HSR_SRC_MAC_INDEX_HI		0xFFFF
+
+#define REG_HSR_ALU_INDEX_2		0x0448
+
+#define HSR_INDEX_MAX			BIT(9)
+#define HSR_DIRECT_INDEX_M		(HSR_INDEX_MAX - 1)
+
+#define REG_HSR_ALU_INDEX_3		0x044C
+
+#define HSR_PATH_INDEX_M		(BIT(4) - 1)
+
+#define REG_HSR_ALU_CTRL__4		0x0450
+
+#define HSR_VALID_CNT_M			(BIT(14) - 1)
+#define HSR_VALID_CNT_S			16
+#define HSR_START			BIT(7)
+#define HSR_VALID			BIT(6)
+#define HSR_SEARCH_END			BIT(5)
+#define HSR_DIRECT			BIT(2)
+#define HSR_ACTION			0x3
+#define HSR_WRITE			1
+#define HSR_READ			2
+#define HSR_SEARCH			3
+
+#define REG_HSR_ALU_VAL_A		0x0454
+
+#define HSR_V_STATIC_VALID		BIT(31)
+#define HSR_V_AGE_CNT_M			(BIT(3) - 1)
+#define HSR_V_AGE_CNT_S			26
+#define HSR_V_PATH_ID_M			(BIT(4) - 1)
+
+#define REG_HSR_ALU_VAL_B		0x0458
+
+#define REG_HSR_ALU_VAL_C		0x045C
+
+#define HSR_V_DST_MAC_ADDR_LO_S		16
+#define HSR_V_SRC_MAC_ADDR_HI		0xFFFF
+
+#define REG_HSR_ALU_VAL_D		0x0460
+
+#define REG_HSR_ALU_VAL_E		0x0464
+
+#define HSR_V_START_SEQ_1_S		16
+#define HSR_V_START_SEQ_2_S		0
+
+#define REG_HSR_ALU_VAL_F		0x0468
+
+#define HSR_V_EXP_SEQ_1_S		16
+#define HSR_V_EXP_SEQ_2_S		0
+
+#define REG_HSR_ALU_VAL_G		0x046C
+
+#define HSR_V_SEQ_CNT_1_S		16
+#define HSR_V_SEQ_CNT_2_S		0
+
+#define HSR_V_SEQ_M			(BIT(16) - 1)
+
+/* 5 - PTP Clock */
+#define REG_PTP_CLK_CTRL		0x0500
+
+#define PTP_STEP_ADJ			BIT(6)
+#define PTP_STEP_DIR			BIT(5)
+#define PTP_READ_TIME			BIT(4)
+#define PTP_LOAD_TIME			BIT(3)
+#define PTP_CLK_ADJ_ENABLE		BIT(2)
+#define PTP_CLK_ENABLE			BIT(1)
+#define PTP_CLK_RESET			BIT(0)
+
+#define REG_PTP_RTC_SUB_NANOSEC__2	0x0502
+
+#define PTP_RTC_SUB_NANOSEC_M		0x0007
+
+#define REG_PTP_RTC_NANOSEC		0x0504
+#define REG_PTP_RTC_NANOSEC_H		0x0504
+#define REG_PTP_RTC_NANOSEC_L		0x0506
+
+#define REG_PTP_RTC_SEC			0x0508
+#define REG_PTP_RTC_SEC_H		0x0508
+#define REG_PTP_RTC_SEC_L		0x050A
+
+#define REG_PTP_SUBNANOSEC_RATE		0x050C
+#define REG_PTP_SUBNANOSEC_RATE_H	0x050C
+
+#define PTP_RATE_DIR			BIT(31)
+#define PTP_TMP_RATE_ENABLE		BIT(30)
+
+#define REG_PTP_SUBNANOSEC_RATE_L	0x050E
+
+#define REG_PTP_RATE_DURATION		0x0510
+#define REG_PTP_RATE_DURATION_H		0x0510
+#define REG_PTP_RATE_DURATION_L		0x0512
+
+#define REG_PTP_MSG_CONF1		0x0514
+
+#define PTP_802_1AS			BIT(7)
+#define PTP_ENABLE			BIT(6)
+#define PTP_ETH_ENABLE			BIT(5)
+#define PTP_IPV4_UDP_ENABLE		BIT(4)
+#define PTP_IPV6_UDP_ENABLE		BIT(3)
+#define PTP_TC_P2P			BIT(2)
+#define PTP_MASTER			BIT(1)
+#define PTP_1STEP			BIT(0)
+
+#define REG_PTP_MSG_CONF2		0x0516
+
+#define PTP_UNICAST_ENABLE		BIT(12)
+#define PTP_ALTERNATE_MASTER		BIT(11)
+#define PTP_ALL_HIGH_PRIO		BIT(10)
+#define PTP_SYNC_CHECK			BIT(9)
+#define PTP_DELAY_CHECK			BIT(8)
+#define PTP_PDELAY_CHECK		BIT(7)
+#define PTP_DROP_SYNC_DELAY_REQ		BIT(5)
+#define PTP_DOMAIN_CHECK		BIT(4)
+#define PTP_UDP_CHECKSUM		BIT(2)
+
+#define REG_PTP_DOMAIN_VERSION		0x0518
+#define PTP_VERSION_M			0xFF00
+#define PTP_DOMAIN_M			0x00FF
+
+#define REG_PTP_UNIT_INDEX__4		0x0520
+
+#define PTP_UNIT_M			0xF
+
+#define PTP_GPIO_INDEX_S		16
+#define PTP_TSI_INDEX_S			8
+#define PTP_TOU_INDEX_S			0
+
+#define REG_PTP_TRIG_STATUS__4		0x0524
+
+#define TRIG_ERROR_S			16
+#define TRIG_DONE_S			0
+
+#define REG_PTP_INT_STATUS__4		0x0528
+
+#define TRIG_INT_S			16
+#define TS_INT_S			0
+
+#define TRIG_UNIT_M			0x7
+#define TS_UNIT_M			0x3
+
+#define REG_PTP_CTRL_STAT__4		0x052C
+
+#define GPIO_IN				BIT(7)
+#define GPIO_OUT			BIT(6)
+#define TS_INT_ENABLE			BIT(5)
+#define TRIG_ACTIVE			BIT(4)
+#define TRIG_ENABLE			BIT(3)
+#define TRIG_RESET			BIT(2)
+#define TS_ENABLE			BIT(1)
+#define TS_RESET			BIT(0)
+
+#define GPIO_CTRL_M			(GPIO_IN | GPIO_OUT)
+
+#define TRIG_CTRL_M			\
+	(TRIG_ACTIVE | TRIG_ENABLE | TRIG_RESET)
+
+#define TS_CTRL_M			\
+	(TS_INT_ENABLE | TS_ENABLE | TS_RESET)
+
+#define REG_TRIG_TARGET_NANOSEC		0x0530
+#define REG_TRIG_TARGET_SEC		0x0534
+
+#define REG_TRIG_CTRL__4		0x0538
+
+#define TRIG_CASCADE_ENABLE		BIT(31)
+#define TRIG_CASCADE_TAIL		BIT(30)
+#define TRIG_CASCADE_UPS_M		0xF
+#define TRIG_CASCADE_UPS_S		26
+#define TRIG_NOW			BIT(25)
+#define TRIG_NOTIFY			BIT(24)
+#define TRIG_EDGE			BIT(23)
+#define TRIG_PATTERN_S			20
+#define TRIG_PATTERN_M			0x7
+#define TRIG_NEG_EDGE			0
+#define TRIG_POS_EDGE			1
+#define TRIG_NEG_PULSE			2
+#define TRIG_POS_PULSE			3
+#define TRIG_NEG_PERIOD			4
+#define TRIG_POS_PERIOD			5
+#define TRIG_REG_OUTPUT			6
+#define TRIG_GPO_S			16
+#define TRIG_GPO_M			0xF
+#define TRIG_CASCADE_ITERATE_CNT_M	0xFFFF
+
+#define REG_TRIG_CYCLE_WIDTH		0x053C
+
+#define REG_TRIG_CYCLE_CNT		0x0540
+
+#define TRIG_CYCLE_CNT_M		0xFFFF
+#define TRIG_CYCLE_CNT_S		16
+#define TRIG_BIT_PATTERN_M		0xFFFF
+
+#define REG_TRIG_ITERATE_TIME		0x0544
+
+#define REG_TRIG_PULSE_WIDTH__4		0x0548
+
+#define TRIG_PULSE_WIDTH_M		0x00FFFFFF
+
+#define REG_TS_CTRL_STAT__4		0x0550
+
+#define TS_EVENT_DETECT_M		0xF
+#define TS_EVENT_DETECT_S		17
+#define TS_EVENT_OVERFLOW		BIT(16)
+#define TS_GPI_M			0xF
+#define TS_GPI_S			8
+#define TS_DETECT_RISE			BIT(7)
+#define TS_DETECT_FALL			BIT(6)
+#define TS_DETECT_S			6
+#define TS_CASCADE_TAIL			BIT(5)
+#define TS_CASCADE_UPS_M		0xF
+#define TS_CASCADE_UPS_S		1
+#define TS_CASCADE_ENABLE		BIT(0)
+
+#define DETECT_RISE			(TS_DETECT_RISE >> TS_DETECT_S)
+#define DETECT_FALL			(TS_DETECT_FALL >> TS_DETECT_S)
+
+#define REG_TS_EVENT_0_NANOSEC		0x0554
+#define REG_TS_EVENT_0_SEC		0x0558
+#define REG_TS_EVENT_0_SUB_NANOSEC	0x055C
+
+#define REG_TS_EVENT_1_NANOSEC		0x0560
+#define REG_TS_EVENT_1_SEC		0x0564
+#define REG_TS_EVENT_1_SUB_NANOSEC	0x0568
+
+#define REG_TS_EVENT_2_NANOSEC		0x056C
+#define REG_TS_EVENT_2_SEC		0x0570
+#define REG_TS_EVENT_2_SUB_NANOSEC	0x0574
+
+#define REG_TS_EVENT_3_NANOSEC		0x0578
+#define REG_TS_EVENT_3_SEC		0x057C
+#define REG_TS_EVENT_3_SUB_NANOSEC	0x0580
+
+#define REG_TS_EVENT_4_NANOSEC		0x0584
+#define REG_TS_EVENT_4_SEC		0x0588
+#define REG_TS_EVENT_4_SUB_NANOSEC	0x058C
+
+#define REG_TS_EVENT_5_NANOSEC		0x0590
+#define REG_TS_EVENT_5_SEC		0x0594
+#define REG_TS_EVENT_5_SUB_NANOSEC	0x0598
+
+#define REG_TS_EVENT_6_NANOSEC		0x059C
+#define REG_TS_EVENT_6_SEC		0x05A0
+#define REG_TS_EVENT_6_SUB_NANOSEC	0x05A4
+
+#define REG_TS_EVENT_7_NANOSEC		0x05A8
+#define REG_TS_EVENT_7_SEC		0x05AC
+#define REG_TS_EVENT_7_SUB_NANOSEC	0x05B0
+
+#define TS_EVENT_EDGE_M			0x1
+#define TS_EVENT_EDGE_S			30
+#define TS_EVENT_NANOSEC_M		(BIT(30) - 1)
+
+#define TS_EVENT_SUB_NANOSEC_M		0x7
+
+#define TS_EVENT_SAMPLE			\
+	(REG_TS_EVENT_1_NANOSEC - REG_TS_EVENT_0_NANOSEC)
+
+#define PORT_CTRL_ADDR(port, addr)	((addr) | (((port) + 1) << 12))
+
+#define REG_GLOBAL_RR_INDEX__1		0x0600
+
+/* DLR */
+#define REG_DLR_SRC_PORT__4		0x0604
+
+#define DLR_SRC_PORT_UNICAST		BIT(31)
+#define DLR_SRC_PORT_M			0x3
+#define DLR_SRC_PORT_BOTH		0
+#define DLR_SRC_PORT_EACH		1
+
+#define REG_DLR_IP_ADDR__4		0x0608
+
+#define REG_DLR_CTRL__1			0x0610
+
+#define DLR_RESET_SEQ_ID		BIT(3)
+#define DLR_BACKUP_AUTO_ON		BIT(2)
+#define DLR_BEACON_TX_ENABLE		BIT(1)
+#define DLR_ASSIST_ENABLE		BIT(0)
+
+#define REG_DLR_STATE__1		0x0611
+
+#define DLR_NODE_STATE_M		0x3
+#define DLR_NODE_STATE_S		1
+#define DLR_NODE_STATE_IDLE		0
+#define DLR_NODE_STATE_FAULT		1
+#define DLR_NODE_STATE_NORMAL		2
+#define DLR_RING_STATE_FAULT		0
+#define DLR_RING_STATE_NORMAL		1
+
+#define REG_DLR_PRECEDENCE__1		0x0612
+
+#define REG_DLR_BEACON_INTERVAL__4	0x0614
+
+#define REG_DLR_BEACON_TIMEOUT__4	0x0618
+
+#define REG_DLR_TIMEOUT_WINDOW__4	0x061C
+
+#define DLR_TIMEOUT_WINDOW_M		(BIT(22) - 1)
+
+#define REG_DLR_VLAN_ID__2		0x0620
+
+#define DLR_VLAN_ID_M			(BIT(12) - 1)
+
+#define REG_DLR_DEST_ADDR_0		0x0622
+#define REG_DLR_DEST_ADDR_1		0x0623
+#define REG_DLR_DEST_ADDR_2		0x0624
+#define REG_DLR_DEST_ADDR_3		0x0625
+#define REG_DLR_DEST_ADDR_4		0x0626
+#define REG_DLR_DEST_ADDR_5		0x0627
+
+#define REG_DLR_PORT_MAP__4		0x0628
+
+#define REG_DLR_CLASS__1		0x062C
+
+#define DLR_FRAME_QID_M			0x3
+
+/* HSR */
+#define REG_HSR_PORT_MAP__4		0x0640
+
+#define REG_HSR_ALU_CTRL_0__1		0x0644
+
+#define HSR_DUPLICATE_DISCARD		BIT(7)
+#define HSR_NODE_UNICAST		BIT(6)
+#define HSR_AGE_CNT_DEFAULT_M		0x7
+#define HSR_AGE_CNT_DEFAULT_S		3
+#define HSR_LEARN_MCAST_DISABLE		BIT(2)
+#define HSR_HASH_OPTION_M		0x3
+#define HSR_HASH_DISABLE		0
+#define HSR_HASH_UPPER_BITS		1
+#define HSR_HASH_LOWER_BITS		2
+#define HSR_HASH_XOR_BOTH_BITS		3
+
+#define REG_HSR_ALU_CTRL_1__1		0x0645
+
+#define HSR_LEARN_UCAST_DISABLE		BIT(7)
+#define HSR_FLUSH_TABLE			BIT(5)
+#define HSR_PROC_MCAST_SRC		BIT(3)
+#define HSR_AGING_ENABLE		BIT(2)
+
+#define REG_HSR_ALU_CTRL_2__2		0x0646
+
+#define REG_HSR_ALU_AGE_PERIOD__4	0x0648
+
+#define REG_HSR_ALU_INT_STATUS__1	0x064C
+#define REG_HSR_ALU_INT_MASK__1		0x064D
+
+#define HSR_WINDOW_OVERFLOW_INT		BIT(3)
+#define HSR_LEARN_FAIL_INT		BIT(2)
+#define HSR_ALMOST_FULL_INT		BIT(1)
+#define HSR_WRITE_FAIL_INT		BIT(0)
+
+#define REG_HSR_ALU_ENTRY_0__2		0x0650
+
+#define HSR_ENTRY_INDEX_M		(BIT(10) - 1)
+#define HSR_FAIL_INDEX_M		(BIT(8) - 1)
+
+#define REG_HSR_ALU_ENTRY_1__2		0x0652
+
+#define HSR_FAIL_LEARN_INDEX_M		(BIT(8) - 1)
+
+#define REG_HSR_ALU_ENTRY_3__2		0x0654
+
+#define HSR_CPU_ACCESS_ENTRY_INDEX_M	(BIT(8) - 1)
+
+/* 0 - Operation */
+#define REG_PORT_DEFAULT_VID		0x0000
+
+#define REG_PORT_CUSTOM_VID		0x0002
+#define REG_PORT_AVB_SR_1_VID		0x0004
+#define REG_PORT_AVB_SR_2_VID		0x0006
+
+#define REG_PORT_AVB_SR_1_TYPE		0x0008
+#define REG_PORT_AVB_SR_2_TYPE		0x000A
+
+#define REG_PORT_PME_STATUS		0x0013
+#define REG_PORT_PME_CTRL		0x0017
+
+#define PME_WOL_MAGICPKT		BIT(2)
+#define PME_WOL_LINKUP			BIT(1)
+#define PME_WOL_ENERGY			BIT(0)
+
+#define REG_PORT_INT_STATUS		0x001B
+#define REG_PORT_INT_MASK		0x001F
+
+#define PORT_SGMII_INT			BIT(3)
+#define PORT_PTP_INT			BIT(2)
+#define PORT_PHY_INT			BIT(1)
+#define PORT_ACL_INT			BIT(0)
+
+#define PORT_INT_MASK			\
+	(PORT_SGMII_INT | PORT_PTP_INT | PORT_PHY_INT | PORT_ACL_INT)
+
+#define REG_PORT_CTRL_0			0x0020
+
+#define PORT_MAC_LOOPBACK		BIT(7)
+#define PORT_FORCE_TX_FLOW_CTRL		BIT(4)
+#define PORT_FORCE_RX_FLOW_CTRL		BIT(3)
+#define PORT_TAIL_TAG_ENABLE		BIT(2)
+#define PORT_QUEUE_SPLIT_ENABLE		0x3
+
+#define REG_PORT_CTRL_1			0x0021
+
+#define PORT_SRP_ENABLE			0x3
+
+#define REG_PORT_STATUS_0		0x0030
+
+#define PORT_INTF_SPEED_M		0x3
+#define PORT_INTF_SPEED_S		3
+#define PORT_INTF_FULL_DUPLEX		BIT(2)
+#define PORT_TX_FLOW_CTRL		BIT(1)
+#define PORT_RX_FLOW_CTRL		BIT(0)
+
+#define REG_PORT_STATUS_1		0x0034
+
+/* 1 - PHY */
+#define REG_PORT_PHY_CTRL		0x0100
+
+#define PORT_PHY_RESET			BIT(15)
+#define PORT_PHY_LOOPBACK		BIT(14)
+#define PORT_SPEED_100MBIT		BIT(13)
+#define PORT_AUTO_NEG_ENABLE		BIT(12)
+#define PORT_POWER_DOWN			BIT(11)
+#define PORT_ISOLATE			BIT(10)
+#define PORT_AUTO_NEG_RESTART		BIT(9)
+#define PORT_FULL_DUPLEX		BIT(8)
+#define PORT_COLLISION_TEST		BIT(7)
+#define PORT_SPEED_1000MBIT		BIT(6)
+
+#define REG_PORT_PHY_STATUS		0x0102
+
+#define PORT_100BT4_CAPABLE		BIT(15)
+#define PORT_100BTX_FD_CAPABLE		BIT(14)
+#define PORT_100BTX_CAPABLE		BIT(13)
+#define PORT_10BT_FD_CAPABLE		BIT(12)
+#define PORT_10BT_CAPABLE		BIT(11)
+#define PORT_EXTENDED_STATUS		BIT(8)
+#define PORT_MII_SUPPRESS_CAPABLE	BIT(6)
+#define PORT_AUTO_NEG_ACKNOWLEDGE	BIT(5)
+#define PORT_REMOTE_FAULT		BIT(4)
+#define PORT_AUTO_NEG_CAPABLE		BIT(3)
+#define PORT_LINK_STATUS		BIT(2)
+#define PORT_JABBER_DETECT		BIT(1)
+#define PORT_EXTENDED_CAPABILITY	BIT(0)
+
+#define REG_PORT_PHY_ID_HI		0x0104
+#define REG_PORT_PHY_ID_LO		0x0106
+
+#define KSZ9477_ID_HI			0x0022
+#define KSZ9477_ID_LO			0x1622
+
+#define REG_PORT_PHY_AUTO_NEGOTIATION	0x0108
+
+#define PORT_AUTO_NEG_NEXT_PAGE		BIT(15)
+#define PORT_AUTO_NEG_REMOTE_FAULT	BIT(13)
+#define PORT_AUTO_NEG_ASYM_PAUSE	BIT(11)
+#define PORT_AUTO_NEG_SYM_PAUSE		BIT(10)
+#define PORT_AUTO_NEG_100BT4		BIT(9)
+#define PORT_AUTO_NEG_100BTX_FD		BIT(8)
+#define PORT_AUTO_NEG_100BTX		BIT(7)
+#define PORT_AUTO_NEG_10BT_FD		BIT(6)
+#define PORT_AUTO_NEG_10BT		BIT(5)
+#define PORT_AUTO_NEG_SELECTOR		0x001F
+#define PORT_AUTO_NEG_802_3		0x0001
+
+#define PORT_AUTO_NEG_PAUSE		\
+	(PORT_AUTO_NEG_ASYM_PAUSE | PORT_AUTO_NEG_SYM_PAUSE)
+
+#define REG_PORT_PHY_REMOTE_CAPABILITY	0x010A
+
+#define PORT_REMOTE_NEXT_PAGE		BIT(15)
+#define PORT_REMOTE_ACKNOWLEDGE		BIT(14)
+#define PORT_REMOTE_REMOTE_FAULT	BIT(13)
+#define PORT_REMOTE_ASYM_PAUSE		BIT(11)
+#define PORT_REMOTE_SYM_PAUSE		BIT(10)
+#define PORT_REMOTE_100BTX_FD		BIT(8)
+#define PORT_REMOTE_100BTX		BIT(7)
+#define PORT_REMOTE_10BT_FD		BIT(6)
+#define PORT_REMOTE_10BT		BIT(5)
+
+#define REG_PORT_PHY_1000_CTRL		0x0112
+
+#define PORT_AUTO_NEG_MANUAL		BIT(12)
+#define PORT_AUTO_NEG_MASTER		BIT(11)
+#define PORT_AUTO_NEG_MASTER_PREFERRED	BIT(10)
+#define PORT_AUTO_NEG_1000BT_FD		BIT(9)
+#define PORT_AUTO_NEG_1000BT		BIT(8)
+
+#define REG_PORT_PHY_1000_STATUS	0x0114
+
+#define PORT_MASTER_FAULT		BIT(15)
+#define PORT_LOCAL_MASTER		BIT(14)
+#define PORT_LOCAL_RX_OK		BIT(13)
+#define PORT_REMOTE_RX_OK		BIT(12)
+#define PORT_REMOTE_1000BT_FD		BIT(11)
+#define PORT_REMOTE_1000BT		BIT(10)
+#define PORT_REMOTE_IDLE_CNT_M		0x0F
+
+#define PORT_PHY_1000_STATIC_STATUS	\
+	(PORT_LOCAL_RX_OK |		\
+	PORT_REMOTE_RX_OK |		\
+	PORT_REMOTE_1000BT_FD |		\
+	PORT_REMOTE_1000BT)
+
+#define REG_PORT_PHY_MMD_SETUP		0x011A
+
+#define PORT_MMD_OP_MODE_M		0x3
+#define PORT_MMD_OP_MODE_S		14
+#define PORT_MMD_OP_INDEX		0
+#define PORT_MMD_OP_DATA_NO_INCR	1
+#define PORT_MMD_OP_DATA_INCR_RW	2
+#define PORT_MMD_OP_DATA_INCR_W		3
+#define PORT_MMD_DEVICE_ID_M		0x1F
+
+#define MMD_SETUP(mode, dev)		\
+	(((u16)(mode) << PORT_MMD_OP_MODE_S) | (dev))
+
+#define REG_PORT_PHY_MMD_INDEX_DATA	0x011C
+
+#define MMD_DEVICE_ID_DSP		1
+
+#define MMD_DSP_SQI_CHAN_A		0xAC
+#define MMD_DSP_SQI_CHAN_B		0xAD
+#define MMD_DSP_SQI_CHAN_C		0xAE
+#define MMD_DSP_SQI_CHAN_D		0xAF
+
+#define DSP_SQI_ERR_DETECTED		BIT(15)
+#define DSP_SQI_AVG_ERR			0x7FFF
+
+#define MMD_DEVICE_ID_COMMON		2
+
+#define MMD_DEVICE_ID_EEE_ADV		7
+
+#define MMD_EEE_ADV			0x3C
+#define EEE_ADV_100MBIT			BIT(1)
+#define EEE_ADV_1GBIT			BIT(2)
+
+#define MMD_EEE_LP_ADV			0x3D
+#define MMD_EEE_MSG_CODE		0x3F
+
+#define MMD_DEVICE_ID_AFED		0x1C
+
+#define REG_PORT_PHY_EXTENDED_STATUS	0x011E
+
+#define PORT_100BTX_FD_ABLE		BIT(15)
+#define PORT_100BTX_ABLE		BIT(14)
+#define PORT_10BT_FD_ABLE		BIT(13)
+#define PORT_10BT_ABLE			BIT(12)
+
+#define REG_PORT_SGMII_ADDR__4		0x0200
+#define PORT_SGMII_AUTO_INCR		BIT(23)
+#define PORT_SGMII_DEVICE_ID_M		0x1F
+#define PORT_SGMII_DEVICE_ID_S		16
+#define PORT_SGMII_ADDR_M		(BIT(21) - 1)
+
+#define REG_PORT_SGMII_DATA__4		0x0204
+#define PORT_SGMII_DATA_M		(BIT(16) - 1)
+
+#define MMD_DEVICE_ID_PMA		0x01
+#define MMD_DEVICE_ID_PCS		0x03
+#define MMD_DEVICE_ID_PHY_XS		0x04
+#define MMD_DEVICE_ID_DTE_XS		0x05
+#define MMD_DEVICE_ID_AN		0x07
+#define MMD_DEVICE_ID_VENDOR_CTRL	0x1E
+#define MMD_DEVICE_ID_VENDOR_MII	0x1F
+
+#define SR_MII				MMD_DEVICE_ID_VENDOR_MII
+
+#define MMD_SR_MII_CTRL			0x0000
+
+#define SR_MII_RESET			BIT(15)
+#define SR_MII_LOOPBACK			BIT(14)
+#define SR_MII_SPEED_100MBIT		BIT(13)
+#define SR_MII_AUTO_NEG_ENABLE		BIT(12)
+#define SR_MII_POWER_DOWN		BIT(11)
+#define SR_MII_AUTO_NEG_RESTART		BIT(9)
+#define SR_MII_FULL_DUPLEX		BIT(8)
+#define SR_MII_SPEED_1000MBIT		BIT(6)
+
+#define MMD_SR_MII_STATUS		0x0001
+#define MMD_SR_MII_ID_1			0x0002
+#define MMD_SR_MII_ID_2			0x0003
+#define MMD_SR_MII_AUTO_NEGOTIATION	0x0004
+
+#define SR_MII_AUTO_NEG_NEXT_PAGE	BIT(15)
+#define SR_MII_AUTO_NEG_REMOTE_FAULT_M	0x3
+#define SR_MII_AUTO_NEG_REMOTE_FAULT_S	12
+#define SR_MII_AUTO_NEG_NO_ERROR	0
+#define SR_MII_AUTO_NEG_OFFLINE		1
+#define SR_MII_AUTO_NEG_LINK_FAILURE	2
+#define SR_MII_AUTO_NEG_ERROR		3
+#define SR_MII_AUTO_NEG_PAUSE_M		0x3
+#define SR_MII_AUTO_NEG_PAUSE_S		7
+#define SR_MII_AUTO_NEG_NO_PAUSE	0
+#define SR_MII_AUTO_NEG_ASYM_PAUSE_TX	1
+#define SR_MII_AUTO_NEG_SYM_PAUSE	2
+#define SR_MII_AUTO_NEG_ASYM_PAUSE_RX	3
+#define SR_MII_AUTO_NEG_HALF_DUPLEX	BIT(6)
+#define SR_MII_AUTO_NEG_FULL_DUPLEX	BIT(5)
+
+#define MMD_SR_MII_REMOTE_CAPABILITY	0x0005
+#define MMD_SR_MII_AUTO_NEG_EXP		0x0006
+#define MMD_SR_MII_AUTO_NEG_EXT		0x000F
+
+#define MMD_SR_MII_DIGITAL_CTRL_1	0x8000
+
+#define MMD_SR_MII_AUTO_NEG_CTRL	0x8001
+
+#define SR_MII_8_BIT			BIT(8)
+#define SR_MII_SGMII_LINK_UP		BIT(4)
+#define SR_MII_TX_CFG_PHY_MASTER	BIT(3)
+#define SR_MII_PCS_MODE_M		0x3
+#define SR_MII_PCS_MODE_S		1
+#define SR_MII_PCS_SGMII		2
+#define SR_MII_AUTO_NEG_COMPLETE_INTR	BIT(0)
+
+#define MMD_SR_MII_AUTO_NEG_STATUS	0x8002
+
+#define SR_MII_STAT_LINK_UP		BIT(4)
+#define SR_MII_STAT_M			0x3
+#define SR_MII_STAT_S			2
+#define SR_MII_STAT_10_MBPS		0
+#define SR_MII_STAT_100_MBPS		1
+#define SR_MII_STAT_1000_MBPS		2
+#define SR_MII_STAT_FULL_DUPLEX		BIT(1)
+
+#define MMD_SR_MII_PHY_CTRL		0x80A0
+
+#define SR_MII_PHY_LANE_SEL_M		0xF
+#define SR_MII_PHY_LANE_SEL_S		8
+#define SR_MII_PHY_WRITE		BIT(1)
+#define SR_MII_PHY_START_BUSY		BIT(0)
+
+#define MMD_SR_MII_PHY_ADDR		0x80A1
+
+#define SR_MII_PHY_ADDR_M		(BIT(16) - 1)
+
+#define MMD_SR_MII_PHY_DATA		0x80A2
+
+#define SR_MII_PHY_DATA_M		(BIT(16) - 1)
+
+#define SR_MII_PHY_JTAG_CHIP_ID_HI	0x000C
+#define SR_MII_PHY_JTAG_CHIP_ID_LO	0x000D
+
+#define REG_PORT_PHY_REMOTE_LB_LED	0x0122
+
+#define PORT_REMOTE_LOOPBACK		BIT(8)
+#define PORT_LED_SELECT			(3 << 6)
+#define PORT_LED_CTRL			(3 << 4)
+#define PORT_LED_CTRL_TEST		BIT(3)
+#define PORT_10BT_PREAMBLE		BIT(2)
+#define PORT_LINK_MD_10BT_ENABLE	BIT(1)
+#define PORT_LINK_MD_PASS		BIT(0)
+
+#define REG_PORT_PHY_LINK_MD		0x0124
+
+#define PORT_START_CABLE_DIAG		BIT(15)
+#define PORT_TX_DISABLE			BIT(14)
+#define PORT_CABLE_DIAG_PAIR_M		0x3
+#define PORT_CABLE_DIAG_PAIR_S		12
+#define PORT_CABLE_DIAG_SELECT_M	0x3
+#define PORT_CABLE_DIAG_SELECT_S	10
+#define PORT_CABLE_DIAG_RESULT_M	0x3
+#define PORT_CABLE_DIAG_RESULT_S	8
+#define PORT_CABLE_STAT_NORMAL		0
+#define PORT_CABLE_STAT_OPEN		1
+#define PORT_CABLE_STAT_SHORT		2
+#define PORT_CABLE_STAT_FAILED		3
+#define PORT_CABLE_FAULT_COUNTER	0x00FF
+
+#define REG_PORT_PHY_PMA_STATUS		0x0126
+
+#define PORT_1000_LINK_GOOD		BIT(1)
+#define PORT_100_LINK_GOOD		BIT(0)
+
+#define REG_PORT_PHY_DIGITAL_STATUS	0x0128
+
+#define PORT_LINK_DETECT		BIT(14)
+#define PORT_SIGNAL_DETECT		BIT(13)
+#define PORT_PHY_STAT_MDI		BIT(12)
+#define PORT_PHY_STAT_MASTER		BIT(11)
+
+#define REG_PORT_PHY_RXER_COUNTER	0x012A
+
+#define REG_PORT_PHY_INT_ENABLE		0x0136
+#define REG_PORT_PHY_INT_STATUS		0x0137
+
+#define JABBER_INT			BIT(7)
+#define RX_ERR_INT			BIT(6)
+#define PAGE_RX_INT			BIT(5)
+#define PARALLEL_DETECT_FAULT_INT	BIT(4)
+#define LINK_PARTNER_ACK_INT		BIT(3)
+#define LINK_DOWN_INT			BIT(2)
+#define REMOTE_FAULT_INT		BIT(1)
+#define LINK_UP_INT			BIT(0)
+
+#define REG_PORT_PHY_DIGITAL_DEBUG_1	0x0138
+
+#define PORT_REG_CLK_SPEED_25_MHZ	BIT(14)
+#define PORT_PHY_FORCE_MDI		BIT(7)
+#define PORT_PHY_AUTO_MDIX_DISABLE	BIT(6)
+
+/* Same as PORT_PHY_LOOPBACK */
+#define PORT_PHY_PCS_LOOPBACK		BIT(0)
+
+#define REG_PORT_PHY_DIGITAL_DEBUG_2	0x013A
+
+#define REG_PORT_PHY_DIGITAL_DEBUG_3	0x013C
+
+#define PORT_100BT_FIXED_LATENCY	BIT(15)
+
+#define REG_PORT_PHY_PHY_CTRL		0x013E
+
+#define PORT_INT_PIN_HIGH		BIT(14)
+#define PORT_ENABLE_JABBER		BIT(9)
+#define PORT_STAT_SPEED_1000MBIT	BIT(6)
+#define PORT_STAT_SPEED_100MBIT		BIT(5)
+#define PORT_STAT_SPEED_10MBIT		BIT(4)
+#define PORT_STAT_FULL_DUPLEX		BIT(3)
+
+/* Same as PORT_PHY_STAT_MASTER */
+#define PORT_STAT_MASTER		BIT(2)
+#define PORT_RESET			BIT(1)
+#define PORT_LINK_STATUS_FAIL		BIT(0)
+
+/* 3 - xMII */
+#define REG_PORT_XMII_CTRL_0		0x0300
+
+#define PORT_SGMII_SEL			BIT(7)
+#define PORT_MII_FULL_DUPLEX		BIT(6)
+#define PORT_MII_100MBIT		BIT(4)
+#define PORT_GRXC_ENABLE		BIT(0)
+
+#define REG_PORT_XMII_CTRL_1		0x0301
+
+#define PORT_RMII_CLK_SEL		BIT(7)
+/* S1 */
+#define PORT_MII_1000MBIT_S1		BIT(6)
+/* S2 */
+#define PORT_MII_NOT_1GBIT		BIT(6)
+#define PORT_MII_SEL_EDGE		BIT(5)
+#define PORT_RGMII_ID_IG_ENABLE		BIT(4)
+#define PORT_RGMII_ID_EG_ENABLE		BIT(3)
+#define PORT_MII_MAC_MODE		BIT(2)
+#define PORT_MII_SEL_M			0x3
+/* S1 */
+#define PORT_MII_SEL_S1			0x0
+#define PORT_RMII_SEL_S1		0x1
+#define PORT_GMII_SEL_S1		0x2
+#define PORT_RGMII_SEL_S1		0x3
+/* S2 */
+#define PORT_RGMII_SEL			0x0
+#define PORT_RMII_SEL			0x1
+#define PORT_GMII_SEL			0x2
+#define PORT_MII_SEL			0x3
+
+/* 4 - MAC */
+#define REG_PORT_MAC_CTRL_0		0x0400
+
+#define PORT_BROADCAST_STORM		BIT(1)
+#define PORT_JUMBO_FRAME		BIT(0)
+
+#define REG_PORT_MAC_CTRL_1		0x0401
+
+#define PORT_BACK_PRESSURE		BIT(3)
+#define PORT_PASS_ALL			BIT(0)
+
+#define REG_PORT_MAC_CTRL_2		0x0402
+
+#define PORT_100BT_EEE_DISABLE		BIT(7)
+#define PORT_1000BT_EEE_DISABLE		BIT(6)
+
+#define REG_PORT_MAC_IN_RATE_LIMIT	0x0403
+
+#define PORT_IN_PORT_BASED_S		6
+#define PORT_RATE_PACKET_BASED_S	5
+#define PORT_IN_FLOW_CTRL_S		4
+#define PORT_COUNT_IFG_S		1
+#define PORT_COUNT_PREAMBLE_S		0
+#define PORT_IN_PORT_BASED		BIT(6)
+#define PORT_IN_PACKET_BASED		BIT(5)
+#define PORT_IN_FLOW_CTRL		BIT(4)
+#define PORT_IN_LIMIT_MODE_M		0x3
+#define PORT_IN_LIMIT_MODE_S		2
+#define PORT_IN_ALL			0
+#define PORT_IN_UNICAST			1
+#define PORT_IN_MULTICAST		2
+#define PORT_IN_BROADCAST		3
+#define PORT_COUNT_IFG			BIT(1)
+#define PORT_COUNT_PREAMBLE		BIT(0)
+
+#define REG_PORT_IN_RATE_0		0x0410
+#define REG_PORT_IN_RATE_1		0x0411
+#define REG_PORT_IN_RATE_2		0x0412
+#define REG_PORT_IN_RATE_3		0x0413
+#define REG_PORT_IN_RATE_4		0x0414
+#define REG_PORT_IN_RATE_5		0x0415
+#define REG_PORT_IN_RATE_6		0x0416
+#define REG_PORT_IN_RATE_7		0x0417
+
+#define REG_PORT_OUT_RATE_0		0x0420
+#define REG_PORT_OUT_RATE_1		0x0421
+#define REG_PORT_OUT_RATE_2		0x0422
+#define REG_PORT_OUT_RATE_3		0x0423
+
+#define PORT_RATE_LIMIT_M		(BIT(7) - 1)
+
+/* 5 - MIB Counters */
+#define REG_PORT_MIB_CTRL_STAT__4	0x0500
+
+#define MIB_COUNTER_OVERFLOW		BIT(31)
+#define MIB_COUNTER_VALID		BIT(30)
+#define MIB_COUNTER_READ		BIT(25)
+#define MIB_COUNTER_FLUSH_FREEZE	BIT(24)
+#define MIB_COUNTER_INDEX_M		(BIT(8) - 1)
+#define MIB_COUNTER_INDEX_S		16
+#define MIB_COUNTER_DATA_HI_M		0xF
+
+#define REG_PORT_MIB_DATA		0x0504
+
+/* 6 - ACL */
+#define REG_PORT_ACL_0			0x0600
+
+#define ACL_FIRST_RULE_M		0xF
+
+#define REG_PORT_ACL_1			0x0601
+
+#define ACL_MODE_M			0x3
+#define ACL_MODE_S			4
+#define ACL_MODE_DISABLE		0
+#define ACL_MODE_LAYER_2		1
+#define ACL_MODE_LAYER_3		2
+#define ACL_MODE_LAYER_4		3
+#define ACL_ENABLE_M			0x3
+#define ACL_ENABLE_S			2
+#define ACL_ENABLE_2_COUNT		0
+#define ACL_ENABLE_2_TYPE		1
+#define ACL_ENABLE_2_MAC		2
+#define ACL_ENABLE_2_BOTH		3
+#define ACL_ENABLE_3_IP			1
+#define ACL_ENABLE_3_SRC_DST_COMP	2
+#define ACL_ENABLE_4_PROTOCOL		0
+#define ACL_ENABLE_4_TCP_PORT_COMP	1
+#define ACL_ENABLE_4_UDP_PORT_COMP	2
+#define ACL_ENABLE_4_TCP_SEQN_COMP	3
+#define ACL_SRC				BIT(1)
+#define ACL_EQUAL			BIT(0)
+
+#define REG_PORT_ACL_2			0x0602
+#define REG_PORT_ACL_3			0x0603
+
+#define ACL_MAX_PORT			0xFFFF
+
+#define REG_PORT_ACL_4			0x0604
+#define REG_PORT_ACL_5			0x0605
+
+#define ACL_MIN_PORT			0xFFFF
+#define ACL_IP_ADDR			0xFFFFFFFF
+#define ACL_TCP_SEQNUM			0xFFFFFFFF
+
+#define REG_PORT_ACL_6			0x0606
+
+#define ACL_RESERVED			0xF8
+#define ACL_PORT_MODE_M			0x3
+#define ACL_PORT_MODE_S			1
+#define ACL_PORT_MODE_DISABLE		0
+#define ACL_PORT_MODE_EITHER		1
+#define ACL_PORT_MODE_IN_RANGE		2
+#define ACL_PORT_MODE_OUT_OF_RANGE	3
+
+#define REG_PORT_ACL_7			0x0607
+
+#define ACL_TCP_FLAG_ENABLE		BIT(0)
+
+#define REG_PORT_ACL_8			0x0608
+
+#define ACL_TCP_FLAG_M			0xFF
+
+#define REG_PORT_ACL_9			0x0609
+
+#define ACL_TCP_FLAG			0xFF
+#define ACL_ETH_TYPE			0xFFFF
+#define ACL_IP_M			0xFFFFFFFF
+
+#define REG_PORT_ACL_A			0x060A
+
+#define ACL_PRIO_MODE_M			0x3
+#define ACL_PRIO_MODE_S			6
+#define ACL_PRIO_MODE_DISABLE		0
+#define ACL_PRIO_MODE_HIGHER		1
+#define ACL_PRIO_MODE_LOWER		2
+#define ACL_PRIO_MODE_REPLACE		3
+#define ACL_PRIO_M			KS_PRIO_M
+#define ACL_PRIO_S			3
+#define ACL_VLAN_PRIO_REPLACE		BIT(2)
+#define ACL_VLAN_PRIO_M			KS_PRIO_M
+#define ACL_VLAN_PRIO_HI_M		0x3
+
+#define REG_PORT_ACL_B			0x060B
+
+#define ACL_VLAN_PRIO_LO_M		0x8
+#define ACL_VLAN_PRIO_S			7
+#define ACL_MAP_MODE_M			0x3
+#define ACL_MAP_MODE_S			5
+#define ACL_MAP_MODE_DISABLE		0
+#define ACL_MAP_MODE_OR			1
+#define ACL_MAP_MODE_AND		2
+#define ACL_MAP_MODE_REPLACE		3
+
+#define ACL_CNT_M			(BIT(11) - 1)
+#define ACL_CNT_S			5
+
+#define REG_PORT_ACL_C			0x060C
+
+#define REG_PORT_ACL_D			0x060D
+#define ACL_MSEC_UNIT			BIT(6)
+#define ACL_INTR_MODE			BIT(5)
+#define ACL_PORT_MAP			0x7F
+
+#define REG_PORT_ACL_E			0x060E
+#define REG_PORT_ACL_F			0x060F
+
+#define REG_PORT_ACL_BYTE_EN_MSB	0x0610
+#define REG_PORT_ACL_BYTE_EN_LSB	0x0611
+
+#define ACL_ACTION_START		0xA
+#define ACL_ACTION_LEN			4
+#define ACL_INTR_CNT_START		0xD
+#define ACL_RULESET_START		0xE
+#define ACL_RULESET_LEN			2
+#define ACL_TABLE_LEN			16
+
+#define ACL_ACTION_ENABLE		0x003C
+#define ACL_MATCH_ENABLE		0x7FC3
+#define ACL_RULESET_ENABLE		0x8003
+#define ACL_BYTE_ENABLE			0xFFFF
+
+#define REG_PORT_ACL_CTRL_0		0x0612
+
+#define PORT_ACL_WRITE_DONE		BIT(6)
+#define PORT_ACL_READ_DONE		BIT(5)
+#define PORT_ACL_WRITE			BIT(4)
+#define PORT_ACL_INDEX_M		0xF
+
+#define REG_PORT_ACL_CTRL_1		0x0613
+
+/* 8 - Classification and Policing */
+#define REG_PORT_MRI_MIRROR_CTRL	0x0800
+
+#define PORT_MIRROR_RX			BIT(6)
+#define PORT_MIRROR_TX			BIT(5)
+#define PORT_MIRROR_SNIFFER		BIT(1)
+
+#define REG_PORT_MRI_PRIO_CTRL		0x0801
+
+#define PORT_HIGHEST_PRIO		BIT(7)
+#define PORT_OR_PRIO			BIT(6)
+#define PORT_MAC_PRIO_ENABLE		BIT(4)
+#define PORT_VLAN_PRIO_ENABLE		BIT(3)
+#define PORT_802_1P_PRIO_ENABLE		BIT(2)
+#define PORT_DIFFSERV_PRIO_ENABLE	BIT(1)
+#define PORT_ACL_PRIO_ENABLE		BIT(0)
+
+#define REG_PORT_MRI_MAC_CTRL		0x0802
+
+#define PORT_USER_PRIO_CEILING		BIT(7)
+#define PORT_DROP_NON_VLAN		BIT(4)
+#define PORT_DROP_TAG			BIT(3)
+#define PORT_BASED_PRIO_M		KS_PRIO_M
+#define PORT_BASED_PRIO_S		0
+
+#define REG_PORT_MRI_AUTHEN_CTRL	0x0803
+
+#define PORT_ACL_ENABLE			BIT(2)
+#define PORT_AUTHEN_MODE		0x3
+#define PORT_AUTHEN_PASS		0
+#define PORT_AUTHEN_BLOCK		1
+#define PORT_AUTHEN_TRAP		2
+
+#define REG_PORT_MRI_INDEX__4		0x0804
+
+#define MRI_INDEX_P_M			0x7
+#define MRI_INDEX_P_S			16
+#define MRI_INDEX_Q_M			0x3
+#define MRI_INDEX_Q_S			0
+
+#define REG_PORT_MRI_TC_MAP__4		0x0808
+
+#define PORT_TC_MAP_M			0xf
+#define PORT_TC_MAP_S			4
+
+#define REG_PORT_MRI_POLICE_CTRL__4	0x080C
+
+#define POLICE_DROP_ALL			BIT(10)
+#define POLICE_PACKET_TYPE_M		0x3
+#define POLICE_PACKET_TYPE_S		8
+#define POLICE_PACKET_DROPPED		0
+#define POLICE_PACKET_GREEN		1
+#define POLICE_PACKET_YELLOW		2
+#define POLICE_PACKET_RED		3
+#define PORT_BASED_POLICING		BIT(7)
+#define NON_DSCP_COLOR_M		0x3
+#define NON_DSCP_COLOR_S		5
+#define COLOR_MARK_ENABLE		BIT(4)
+#define COLOR_REMAP_ENABLE		BIT(3)
+#define POLICE_DROP_SRP			BIT(2)
+#define POLICE_COLOR_NOT_AWARE		BIT(1)
+#define POLICE_ENABLE			BIT(0)
+
+#define REG_PORT_POLICE_COLOR_0__4	0x0810
+#define REG_PORT_POLICE_COLOR_1__4	0x0814
+#define REG_PORT_POLICE_COLOR_2__4	0x0818
+#define REG_PORT_POLICE_COLOR_3__4	0x081C
+
+#define POLICE_COLOR_MAP_S		2
+#define POLICE_COLOR_MAP_M		(BIT(POLICE_COLOR_MAP_S) - 1)
+
+#define REG_PORT_POLICE_RATE__4		0x0820
+
+#define POLICE_CIR_S			16
+#define POLICE_PIR_S			0
+
+#define REG_PORT_POLICE_BURST_SIZE__4	0x0824
+
+#define POLICE_BURST_SIZE_M		0x3FFF
+#define POLICE_CBS_S			16
+#define POLICE_PBS_S			0
+
+#define REG_PORT_WRED_PM_CTRL_0__4	0x0830
+
+#define WRED_PM_CTRL_M			(BIT(11) - 1)
+
+#define WRED_PM_MAX_THRESHOLD_S		16
+#define WRED_PM_MIN_THRESHOLD_S		0
+
+#define REG_PORT_WRED_PM_CTRL_1__4	0x0834
+
+#define WRED_PM_MULTIPLIER_S		16
+#define WRED_PM_AVG_QUEUE_SIZE_S	0
+
+#define REG_PORT_WRED_QUEUE_CTRL_0__4	0x0840
+#define REG_PORT_WRED_QUEUE_CTRL_1__4	0x0844
+
+#define REG_PORT_WRED_QUEUE_PMON__4	0x0848
+
+#define WRED_RANDOM_DROP_ENABLE		BIT(31)
+#define WRED_PMON_FLUSH			BIT(30)
+#define WRED_DROP_GYR_DISABLE		BIT(29)
+#define WRED_DROP_YR_DISABLE		BIT(28)
+#define WRED_DROP_R_DISABLE		BIT(27)
+#define WRED_DROP_ALL			BIT(26)
+#define WRED_PMON_M			(BIT(24) - 1)
+
+/* 9 - Shaping */
+
+#define REG_PORT_MTI_QUEUE_INDEX__4	0x0900
+
+#define REG_PORT_MTI_QUEUE_CTRL_0__4	0x0904
+
+#define MTI_PVID_REPLACE		BIT(0)
+
+#define REG_PORT_MTI_QUEUE_CTRL_0	0x0914
+
+#define MTI_SCHEDULE_MODE_M		0x3
+#define MTI_SCHEDULE_MODE_S		6
+#define MTI_SCHEDULE_STRICT_PRIO	0
+#define MTI_SCHEDULE_WRR		2
+#define MTI_SHAPING_M			0x3
+#define MTI_SHAPING_S			4
+#define MTI_SHAPING_OFF			0
+#define MTI_SHAPING_SRP			1
+#define MTI_SHAPING_TIME_AWARE		2
+
+#define REG_PORT_MTI_QUEUE_CTRL_1	0x0915
+
+#define MTI_TX_RATIO_M			(BIT(7) - 1)
+
+#define REG_PORT_MTI_QUEUE_CTRL_2__2	0x0916
+#define REG_PORT_MTI_HI_WATER_MARK	0x0916
+#define REG_PORT_MTI_QUEUE_CTRL_3__2	0x0918
+#define REG_PORT_MTI_LO_WATER_MARK	0x0918
+#define REG_PORT_MTI_QUEUE_CTRL_4__2	0x091A
+#define REG_PORT_MTI_CREDIT_INCREMENT	0x091A
+
+/* A - QM */
+
+#define REG_PORT_QM_CTRL__4		0x0A00
+
+#define PORT_QM_DROP_PRIO_M		0x3
+
+#define REG_PORT_VLAN_MEMBERSHIP__4	0x0A04
+
+#define REG_PORT_QM_QUEUE_INDEX__4	0x0A08
+
+#define PORT_QM_QUEUE_INDEX_S		24
+#define PORT_QM_BURST_SIZE_S		16
+#define PORT_QM_MIN_RESV_SPACE_M	(BIT(11) - 1)
+
+#define REG_PORT_QM_WATER_MARK__4	0x0A0C
+
+#define PORT_QM_HI_WATER_MARK_S		16
+#define PORT_QM_LO_WATER_MARK_S		0
+#define PORT_QM_WATER_MARK_M		(BIT(11) - 1)
+
+#define REG_PORT_QM_TX_CNT_0__4		0x0A10
+
+#define PORT_QM_TX_CNT_USED_S		0
+#define PORT_QM_TX_CNT_M		(BIT(11) - 1)
+
+#define REG_PORT_QM_TX_CNT_1__4		0x0A14
+
+#define PORT_QM_TX_CNT_CALCULATED_S	16
+#define PORT_QM_TX_CNT_AVAIL_S		0
+
+/* B - LUE */
+#define REG_PORT_LUE_CTRL		0x0B00
+
+#define PORT_VLAN_LOOKUP_VID_0		BIT(7)
+#define PORT_INGRESS_FILTER		BIT(6)
+#define PORT_DISCARD_NON_VID		BIT(5)
+#define PORT_MAC_BASED_802_1X		BIT(4)
+#define PORT_SRC_ADDR_FILTER		BIT(3)
+
+#define REG_PORT_LUE_MSTP_INDEX		0x0B01
+
+#define REG_PORT_LUE_MSTP_STATE		0x0B04
+
+#define PORT_TX_ENABLE			BIT(2)
+#define PORT_RX_ENABLE			BIT(1)
+#define PORT_LEARN_DISABLE		BIT(0)
+
+/* C - PTP */
+
+#define REG_PTP_PORT_RX_DELAY__2	0x0C00
+#define REG_PTP_PORT_TX_DELAY__2	0x0C02
+#define REG_PTP_PORT_ASYM_DELAY__2	0x0C04
+
+#define REG_PTP_PORT_XDELAY_TS		0x0C08
+#define REG_PTP_PORT_XDELAY_TS_H	0x0C08
+#define REG_PTP_PORT_XDELAY_TS_L	0x0C0A
+
+#define REG_PTP_PORT_SYNC_TS		0x0C0C
+#define REG_PTP_PORT_SYNC_TS_H		0x0C0C
+#define REG_PTP_PORT_SYNC_TS_L		0x0C0E
+
+#define REG_PTP_PORT_PDRESP_TS		0x0C10
+#define REG_PTP_PORT_PDRESP_TS_H	0x0C10
+#define REG_PTP_PORT_PDRESP_TS_L	0x0C12
+
+#define REG_PTP_PORT_TX_INT_STATUS__2	0x0C14
+#define REG_PTP_PORT_TX_INT_ENABLE__2	0x0C16
+
+#define PTP_PORT_SYNC_INT		BIT(15)
+#define PTP_PORT_XDELAY_REQ_INT		BIT(14)
+#define PTP_PORT_PDELAY_RESP_INT	BIT(13)
+
+#define REG_PTP_PORT_LINK_DELAY__4	0x0C18
+
+#define PRIO_QUEUES			4
+#define RX_PRIO_QUEUES			8
+
+#define KS_PRIO_IN_REG			2
+
+#define TOTAL_PORT_NUM			7
+
+#define KSZ9477_COUNTER_NUM		0x20
+#define TOTAL_KSZ9477_COUNTER_NUM	(KSZ9477_COUNTER_NUM + 2 + 2)
+
+#define SWITCH_COUNTER_NUM		KSZ9477_COUNTER_NUM
+#define TOTAL_SWITCH_COUNTER_NUM	TOTAL_KSZ9477_COUNTER_NUM
+
+#define P_BCAST_STORM_CTRL		REG_PORT_MAC_CTRL_0
+#define P_PRIO_CTRL			REG_PORT_MRI_PRIO_CTRL
+#define P_MIRROR_CTRL			REG_PORT_MRI_MIRROR_CTRL
+#define P_STP_CTRL			REG_PORT_LUE_MSTP_STATE
+#define P_PHY_CTRL			REG_PORT_PHY_CTRL
+#define P_NEG_RESTART_CTRL		REG_PORT_PHY_CTRL
+#define P_LINK_STATUS			REG_PORT_PHY_STATUS
+#define P_SPEED_STATUS			REG_PORT_PHY_PHY_CTRL
+#define P_RATE_LIMIT_CTRL		REG_PORT_MAC_IN_RATE_LIMIT
+
+#define S_LINK_AGING_CTRL		REG_SW_LUE_CTRL_1
+#define S_MIRROR_CTRL			REG_SW_MRI_CTRL_0
+#define S_REPLACE_VID_CTRL		REG_SW_MAC_CTRL_2
+#define S_802_1P_PRIO_CTRL		REG_SW_MAC_802_1P_MAP_0
+#define S_TOS_PRIO_CTRL			REG_SW_MAC_TOS_PRIO_0
+#define S_FLUSH_TABLE_CTRL		REG_SW_LUE_CTRL_1
+
+#define SW_FLUSH_DYN_MAC_TABLE		SW_FLUSH_MSTP_TABLE
+
+#define MAX_TIMESTAMP_UNIT		2
+#define MAX_TRIG_UNIT			3
+#define MAX_TIMESTAMP_EVENT_UNIT	8
+#define MAX_GPIO			4
+
+#define PTP_TRIG_UNIT_M			(BIT(MAX_TRIG_UNIT) - 1)
+#define PTP_TS_UNIT_M			(BIT(MAX_TIMESTAMP_UNIT) - 1)
+
+/* Driver set switch broadcast storm protection at 10% rate. */
+#define BROADCAST_STORM_PROT_RATE	10
+
+/* 148,800 frames * 67 ms / 100 */
+#define BROADCAST_STORM_VALUE		9969
+
+#endif /* KSZ9477_REGS_H */
-- 
2.30.2


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox