* [PATCH v2 2/2] ARM: i.MX7: add 96Boards Meerkat96 support
2022-07-11 14:12 [PATCH v2 1/2] ARM: i.MX: configs: add recent boards to imx_v7_defconfig Johannes Zink
@ 2022-07-11 14:12 ` Johannes Zink
2022-07-11 14:21 ` Ahmad Fatoum
2022-07-12 5:04 ` [PATCH] fixup! " Johannes Zink
0 siblings, 2 replies; 5+ messages in thread
From: Johannes Zink @ 2022-07-11 14:12 UTC (permalink / raw)
To: barebox; +Cc: Johannes Zink
This is a i.MX7D-based board with an upstream device tree.
Add the necessary boilerplate to have barebox create an image.
The memory settings are taken from U-Boot v2022.07-rc6.
System reset requires pmic driver which is not available yet in barebox.
Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
---
v1 -> v2:
- added meerkat96 board to imx_v7_defconfig
- added Documentation for meerkat96 board
---
Documentation/boards/imx/meerkat96.rst | 31 ++++++
arch/arm/boards/Makefile | 1 +
arch/arm/boards/meerkat96/Makefile | 4 +
arch/arm/boards/meerkat96/board.c | 10 ++
| 105 ++++++++++++++++++
arch/arm/boards/meerkat96/lowlevel.c | 34 ++++++
arch/arm/configs/imx_v7_defconfig | 1 +
arch/arm/dts/Makefile | 1 +
arch/arm/dts/imx7d-meerkat96.dts | 42 +++++++
arch/arm/mach-imx/Kconfig | 5 +
images/Makefile.imx | 5 +
11 files changed, 239 insertions(+)
create mode 100644 Documentation/boards/imx/meerkat96.rst
create mode 100644 arch/arm/boards/meerkat96/Makefile
create mode 100644 arch/arm/boards/meerkat96/board.c
create mode 100644 arch/arm/boards/meerkat96/flash-header-mx7-meerkat96.imxcfg
create mode 100644 arch/arm/boards/meerkat96/lowlevel.c
create mode 100644 arch/arm/dts/imx7d-meerkat96.dts
diff --git a/Documentation/boards/imx/meerkat96.rst b/Documentation/boards/imx/meerkat96.rst
new file mode 100644
index 000000000..3cdb1beaf
--- /dev/null
+++ b/Documentation/boards/imx/meerkat96.rst
@@ -0,0 +1,31 @@
+Meerkat 96
+==========
+
+The Meerkat96 is a single board computer based on an i.MX7D SoC by NXP, featuring a dual core ARM Cortex-A7 at 1 GHz and a Cortex-M4 at 266MHz and 512 MB DRAM. For further details on the board's features check the manufacturers page at https://www.96boards.org/product/imx7-96
+
+Serial console
+--------------
+
+UART6 of the i.MX7D is broken out to Pinheader J3, on the Silkscreen the Pins are labeled with B (Ground), W (UART 6 TX) and G (UART 6 RX). If you use the UART-To-Serial-Converter provided with the board, you can just connect the Black jumper to B, the White to W and the Green to G. The UART uses 3.3V levels.
+
+Building Barebox
+----------------
+
+To build Barebox for ZII i.MX7 based boards do the following:
+
+.. code-block:: sh
+
+ make ARCH=arm CROSS_COMPILE=<ARM toolchain prefix> mrproper
+ make ARCH=arm CROSS_COMPILE=<ARM toolchain prefix> imx_v7_defconfig
+ make ARCH=arm CROSS_COMPILE=<ARM toolchain prefix>
+
+Bringup
+-------
+
+flash the resulting barebox-meerkat96.img to an sdcard at address 0. Make sure the pmic is set to power-on state by setting the dipswitch SW3 on the boards bottom side to 1-1 (i.e. all switches on, which is the factory default).
+
+Schematics
+----------
+
+Schematics are available at https://github.com/96boards/documentation/blob/master/consumer/imx7-96/hardware-docs/files/iMX7-96-schematics.pdf
+
diff --git a/arch/arm/boards/Makefile b/arch/arm/boards/Makefile
index 3ccde26f1..96f81a32d 100644
--- a/arch/arm/boards/Makefile
+++ b/arch/arm/boards/Makefile
@@ -52,6 +52,7 @@ obj-$(CONFIG_MACH_FREESCALE_MX53_LOCO) += freescale-mx53-qsb/
obj-$(CONFIG_MACH_FREESCALE_MX53_SMD) += freescale-mx53-smd/
obj-$(CONFIG_MACH_FREESCALE_MX53_VMX53) += freescale-mx53-vmx53/
obj-$(CONFIG_MACH_FREESCALE_MX7_SABRESD) += freescale-mx7-sabresd/
+obj-$(CONFIG_MACH_MEERKAT96) += meerkat96/
obj-$(CONFIG_MACH_GE863) += telit-evk-pro3/
obj-$(CONFIG_MACH_GK802) += gk802/
obj-$(CONFIG_MACH_GLOBALSCALE_GURUPLUG) += globalscale-guruplug/
diff --git a/arch/arm/boards/meerkat96/Makefile b/arch/arm/boards/meerkat96/Makefile
new file mode 100644
index 000000000..567871818
--- /dev/null
+++ b/arch/arm/boards/meerkat96/Makefile
@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0-only
+
+lwl-y += lowlevel.o
+obj-y += board.o
diff --git a/arch/arm/boards/meerkat96/board.c b/arch/arm/boards/meerkat96/board.c
new file mode 100644
index 000000000..49e9c06f7
--- /dev/null
+++ b/arch/arm/boards/meerkat96/board.c
@@ -0,0 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include <of.h>
+#include <deep-probe.h>
+
+static const struct of_device_id meerkat96_match[] = {
+ { .compatible = "novtech,imx7d-meerkat96" },
+ { /* Sentinel */ },
+};
+BAREBOX_DEEP_PROBE_ENABLE(meerkat96_match);
--git a/arch/arm/boards/meerkat96/flash-header-mx7-meerkat96.imxcfg b/arch/arm/boards/meerkat96/flash-header-mx7-meerkat96.imxcfg
new file mode 100644
index 000000000..a49b81617
--- /dev/null
+++ b/arch/arm/boards/meerkat96/flash-header-mx7-meerkat96.imxcfg
@@ -0,0 +1,105 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2014 Freescale Semiconductor, Inc.
+ */
+
+soc imx7
+loadaddr 0x80000000
+ivtofs 0x400
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type Address Value
+ *
+ * where:
+ * Addr-type register length (1,2 or 4 bytes)
+ * Address absolute address of the register
+ * value value to be stored in the register
+ */
+
+/* Enable OCRAM EPDC */
+wm 32 0x30340004 0x4F400005
+
+/* =============================================================================
+ * DDR Controller Registers
+ * =============================================================================
+ * Memory type: DDR3
+ * Manufacturer: ISSI
+ * Device Part Number: IS43TR16256AL-125KBL
+ * Clock Freq.: 533MHz
+ * Density per CS in Gb: 4
+ * Chip Selects used: 1
+ * Number of Banks: 8
+ * Row address: 15
+ * Column address: 10
+ * Data bus width: 16
+ * ROW-BANK interleave: ENABLED
+ * =============================================================================
+ */
+
+wm 32 0x30391000 0x00000002 // deassert presetn
+wm 32 0x307A0000 0x01041001 // DDRC_MSTR
+wm 32 0x307A0064 0x00400046 // DDRC_RFSHTMG
+wm 32 0x307a0490 0x00000001 // DDRC_PCTRL_0
+wm 32 0x307A00D4 0x00690000 // DDRC_INIT1
+wm 32 0x307A00D0 0x00020083 // DDRC_INIT0
+wm 32 0x307A00DC 0x09300004 // DDRC_INIT3
+wm 32 0x307A00E0 0x04080000 // DDRC_INIT4
+wm 32 0x307A00E4 0x00100004 // DDRC_INIT5
+wm 32 0x307A00F4 0x0000033F // DDRC_RANKCTL
+wm 32 0x307A0100 0x090B1109 // DDRC_DRAMTMG0
+wm 32 0x307A0104 0x0007020D // DDRC_DRAMTMG1
+wm 32 0x307A0108 0x03040407 // DDRC_DRAMTMG2
+wm 32 0x307A010C 0x00002006 // DDRC_DRAMTMG3
+wm 32 0x307A0110 0x04020205 // DDRC_DRAMTMG4
+wm 32 0x307A0114 0x03030202 // DDRC_DRAMTMG5
+wm 32 0x307A0120 0x00000803 // DDRC_DRAMTMG8
+wm 32 0x307A0180 0x00800020 // DDRC_ZQCTL0
+wm 32 0x307A0190 0x02098204 // DDRC_DFITMG0
+wm 32 0x307A0194 0x00030303 // DDRC_DFITMG1
+wm 32 0x307A01A0 0x80400003 // DDRC_DFIUPD0
+wm 32 0x307A01A4 0x00100020 // DDRC_DFIUPD1
+wm 32 0x307A01A8 0x80100004 // DDRC_DFIUPD2
+wm 32 0x307A0200 0x00000015 // DDRC_ADDRMAP0
+wm 32 0x307A0204 0x00070707 // DDRC_ADDRMAP1
+wm 32 0x307A0210 0x00000F0F // DDRC_ADDRMAP4
+wm 32 0x307A0214 0x06060606 // DDRC_ADDRMAP5
+wm 32 0x307A0218 0x0F060606 // DDRC_ADDRMAP6
+wm 32 0x307A0240 0x06000604 // DDRC_ODTCFG
+wm 32 0x307A0244 0x00000001 // DDRC_ODTMAP
+
+
+/* =============================================================================
+ * PHY Control Register
+ * =============================================================================
+ */
+
+wm 32 0x30391000 0x00000000 // deassert presetn
+wm 32 0x30790000 0x17420F40 // DDR_PHY_PHY_CON0
+wm 32 0x30790004 0x10210100 // DDR_PHY_PHY_CON1
+wm 32 0x30790010 0x00060807 // DDR_PHY_PHY_CON4
+wm 32 0x307900B0 0x1010007E // DDR_PHY_MDLL_CON0
+wm 32 0x3079009C 0x00000D6E // DDR_PHY_DRVDS_CON0
+wm 32 0x30790030 0x08080808 // DDR_PHY_OFFSET_WR_CON0
+wm 32 0x30790020 0x08080808 // DDR_PHY_OFFSET_RD_CON0
+wm 32 0x30790050 0x01000010 // DDR_PHY_OFFSETD_CON0
+wm 32 0x30790050 0x00000010 // DDR_PHY_OFFSETD_CON0
+wm 32 0x30790018 0x0000000F // DDR_PHY_LP_CON0
+wm 32 0x307900C0 0x0E407304 // DDR_PHY_ZQ_CON0 - Start Manual ZQ
+wm 32 0x307900C0 0x0E447304
+wm 32 0x307900C0 0x0E447306
+wm 32 0x307900C0 0x0E447304 // <= NOTE: Depending on JTAG device used, may need ~ 7 us pause at this point.
+wm 32 0x307900C0 0x0E407304 // DDR_PHY_ZQ_CON0 - End Manual ZQ
+
+
+/* =============================================================================
+ * Final Initialization start sequence
+ * =============================================================================
+ */
+
+wm 32 0x30384130 0x00000000 // Disable Clock
+wm 32 0x30340020 0x00000178 // IOMUX_GRP_GRP8 - Start input to PHY
+wm 32 0x30384130 0x00000002 // Enable Clock
+/* <= NOTE: Depending on JTAG device used, may need ~ 250 us pause at this point. */
diff --git a/arch/arm/boards/meerkat96/lowlevel.c b/arch/arm/boards/meerkat96/lowlevel.c
new file mode 100644
index 000000000..1c9baeacf
--- /dev/null
+++ b/arch/arm/boards/meerkat96/lowlevel.c
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <debug_ll.h>
+#include <io.h>
+#include <linux/sizes.h>
+#include <mach/debug_ll.h>
+#include <mach/iomux-mx7.h>
+#include <mach/imx7-ccm-regs.h>
+#include <mach/generic.h>
+#include <asm/barebox-arm-head.h>
+#include <asm/barebox-arm.h>
+#include <asm/cache.h>
+extern char __dtb_z_imx7d_meerkat96_start[];
+
+static void setup_uart(void)
+{
+ imx7_early_setup_uart_clock();
+ imx7_setup_pad(MX7D_PAD_SD1_WP__UART6_DCE_TX);
+ imx7_uart_setup_ll();
+ putc_ll('>');
+}
+
+ENTRY_FUNCTION_WITHSTACK(start_imx7d_meerkat96, 0, r0, r1, r2)
+{
+ void *fdt;
+
+ imx7_cpu_lowlevel_init();
+
+ setup_uart();
+
+ fdt = __dtb_z_imx7d_meerkat96_start + get_runtime_offset();
+
+ barebox_arm_entry(0x80000000, SZ_512M, fdt);
+}
diff --git a/arch/arm/configs/imx_v7_defconfig b/arch/arm/configs/imx_v7_defconfig
index 8ae515ae7..df2304eae 100644
--- a/arch/arm/configs/imx_v7_defconfig
+++ b/arch/arm/configs/imx_v7_defconfig
@@ -38,6 +38,7 @@ CONFIG_MACH_CM_FX6=y
CONFIG_MACH_ADVANTECH_ROM_742X=y
CONFIG_MACH_WARP7=y
CONFIG_MACH_AC_SXB=y
+CONFIG_MACH_MEERKAT96=y
CONFIG_MACH_VF610_TWR=y
CONFIG_MACH_ZII_RDU1=y
CONFIG_MACH_ZII_RDU2=y
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 0c7e43e22..8cd994cf0 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -26,6 +26,7 @@ lwl-$(CONFIG_MACH_CCMX53) += imx53-ccxmx53.dtb.o
lwl-$(CONFIG_MACH_DIGI_CCIMX6ULSBCPRO) += imx6ul-ccimx6ulsbcpro.dtb.o
lwl-$(CONFIG_MACH_FREESCALE_MX53_VMX53) += imx53-voipac-bsb.dtb.o
lwl-$(CONFIG_MACH_FREESCALE_MX7_SABRESD) += imx7d-sdb.dtb.o
+lwl-$(CONFIG_MACH_MEERKAT96) += imx7d-meerkat96.dtb.o
lwl-$(CONFIG_MACH_GK802) += imx6q-gk802.dtb.o
lwl-$(CONFIG_MACH_GLOBALSCALE_GURUPLUG) += kirkwood-guruplug-server-plus-bb.dtb.o
lwl-$(CONFIG_MACH_GLOBALSCALE_MIRABOX) += armada-370-mirabox-bb.dtb.o
diff --git a/arch/arm/dts/imx7d-meerkat96.dts b/arch/arm/dts/imx7d-meerkat96.dts
new file mode 100644
index 000000000..f9d18f355
--- /dev/null
+++ b/arch/arm/dts/imx7d-meerkat96.dts
@@ -0,0 +1,42 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+#include <arm/imx7d-meerkat96.dts>
+
+/ {
+ chosen {
+ environment {
+ compatible = "barebox,environment";
+ device-path = &bareboxenv;
+ };
+ };
+};
+
+&usdhc1 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ barebox@0 {
+ label = "barebox";
+ reg = <0x0 0x180000>;
+ };
+
+ bareboxenv: bareboxenv@180000 {
+ label = "bareboxenv";
+ reg = <0x180000 0x80000>;
+ };
+};
+
+/* FIXME: barebox serial is broken when barebox applies requested reparenting */
+&uart1 {
+ /delete-property/ assigned-clocks;
+ /delete-property/ assigned-clock-parents;
+};
+
+&uart3 {
+ /delete-property/ assigned-clocks;
+ /delete-property/ assigned-clock-parents;
+};
+
+&uart6 {
+ /delete-property/ assigned-clocks;
+ /delete-property/ assigned-clock-parents;
+};
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index 9ff549ac8..c10b09a12 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -485,6 +485,11 @@ config MACH_AC_SXB
select MCI_IMX_ESDHC_PBL
select ARM_USE_COMPRESSED_DTB
+config MACH_MEERKAT96
+ bool "96Boards: i.MX7 Meerkat96"
+ select ARCH_IMX7
+ select ARM_USE_COMPRESSED_DTB
+
config MACH_VF610_TWR
bool "Freescale VF610 Tower Board"
select ARCH_VF610
diff --git a/images/Makefile.imx b/images/Makefile.imx
index 62549ab75..a19e0ff1c 100644
--- a/images/Makefile.imx
+++ b/images/Makefile.imx
@@ -418,6 +418,11 @@ CFG_start_zii_imx7d_dev.pblb.imximg = $(board)/zii-imx7d-dev/flash-header-zii-im
FILE_barebox-zii-imx7d-dev.img = start_zii_imx7d_dev.pblb.imximg
image-$(CONFIG_MACH_ZII_IMX7D_DEV) += barebox-zii-imx7d-dev.img
+pblb-$(CONFIG_MACH_MEERKAT96) += start_imx7d_meerkat96
+CFG_start_imx7d_meerkat96.pblb.imximg = $(board)/meerkat96/flash-header-mx7-meerkat96.imxcfg
+FILE_barebox-meerkat96.img = start_imx7d_meerkat96.pblb.imximg
+image-$(CONFIG_MACH_MEERKAT96) += barebox-meerkat96.img
+
pblb-$(CONFIG_MACH_KAMSTRUP_MX7_CONCENTRATOR) += start_kamstrup_mx7_concentrator
CFG_start_kamstrup_mx7_concentrator.pblb.imximg = $(board)/kamstrup-mx7-concentrator/flash-header-tqma7d.imxcfg
FILE_barebox-kamstrup-mx7-concentrator.img = start_kamstrup_mx7_concentrator.pblb.imximg
--
2.30.2
^ permalink raw reply [flat|nested] 5+ messages in thread