Re: [PATCH] fixup! ARM: i.MX7: add 96Boards Meerkat96 support

[Sascha Hauer <sha@pengutronix.de>]

Hi Johannes,

On Tue, Jul 12, 2022 at 07:04:49AM +0200, Johannes Zink wrote:
> This is a fixup for the documentation: fixed line breaks, whitespace changes 
> and typos as requested.
> 
> Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
> ---
>  Documentation/boards/imx/meerkat96.rst | 28 ++++++++++++++++++--------
>  1 file changed, 20 insertions(+), 8 deletions(-)

Still many trailing whitespaces with this fixup. I fixed it up locally
and applied, thanks

Sascha

> 
> diff --git a/Documentation/boards/imx/meerkat96.rst b/Documentation/boards/imx/meerkat96.rst
> index 3cdb1beaf..3a51b9144 100644
> --- a/Documentation/boards/imx/meerkat96.rst
> +++ b/Documentation/boards/imx/meerkat96.rst
> @@ -1,28 +1,40 @@
>  Meerkat 96
>  ==========
>  
> -The Meerkat96 is a single board computer based on an i.MX7D SoC by NXP, featuring a dual core ARM Cortex-A7 at 1 GHz and a Cortex-M4 at 266MHz and 512 MB DRAM. For further details on the board's features check the manufacturers page at https://www.96boards.org/product/imx7-96
> +The Meerkat96 is a single board computer based on an i.MX7D SoC by NXP, 
> +featuring a dual core ARM Cortex-A7 at 1 GHz and a Cortex-M4 at 266MHz 
> +and 512 MB DRAM. For further details on the board's features check the 
> +manufacturers page at https://www.96boards.org/product/imx7-96
>  
>  Serial console
>  --------------
>  
> -UART6 of the i.MX7D is broken out to Pinheader J3, on the Silkscreen the Pins are labeled with B (Ground), W (UART 6 TX) and G (UART 6 RX). If you use the UART-To-Serial-Converter provided with the board, you can just connect the Black jumper to B, the White to W and the Green to G. The UART uses 3.3V levels. 
> +UART6 of the i.MX7D is broken out to Pinheader J3, on the Silkscreen 
> +the Pins are labeled with B (Ground), W (UART 6 TX) and G (UART 6 RX). 
> +If you use the UART-To-USB-Converter provided with the board, you can 
> +just connect the Black jumper to B, the White to W and the Green to G. 
> +
> +The UART uses 3.3V levels. 
>  
>  Building Barebox                                                        
>  ----------------                                                        
>                                                                          
> -To build Barebox for ZII i.MX7 based boards do the following:           
> -                                                                        
> -.. code-block:: sh                                                      
> -           
> -  make ARCH=arm CROSS_COMPILE=<ARM toolchain prefix> mrproper   
> +To build Barebox for the meerkat96 board do the following:
> +
> +.. code-block:: sh
> +
> +  make ARCH=arm CROSS_COMPILE=<ARM toolchain prefix> mrproper
>    make ARCH=arm CROSS_COMPILE=<ARM toolchain prefix> imx_v7_defconfig
>    make ARCH=arm CROSS_COMPILE=<ARM toolchain prefix>
>  
>  Bringup
>  -------
>  
> -flash the resulting barebox-meerkat96.img to an sdcard at address 0. Make sure the pmic is set to power-on state by setting the dipswitch SW3 on the boards bottom side to 1-1 (i.e. all switches on, which is the factory default).
> +flash the resulting barebox-meerkat96.img to an sdcard at address 0. 
> +
> +Make sure the pmic is set to power-on state by setting the dipswitch 
> +SW3 on the boards bottom side to 1-1 (i.e. all switches on, which is 
> +the factory default).
>  
>  Schematics
>  ----------
> -- 
> 2.30.2
> 
> 
> 

-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |