From: John Watts <contact@jookia.org>
To: barebox@lists.infradead.org
Cc: John Watts <contact@jookia.org>
Subject: [PATCH 2/5] ARM: novena: Setup RAM using static configuration
Date: Mon, 23 Jan 2023 04:51:38 +1100 [thread overview]
Message-ID: <20230122175141.119834-3-contact@jookia.org> (raw)
In-Reply-To: <20230122175141.119834-1-contact@jookia.org>
The Novena laptops were shipped with a 4GB stick that can be set up
using this DDR3 configuration.
This isn't ideal as the stick is swappable, but it will work for
most people.
The DDR registers are copied from /board/kosagi/novena/novena_spl.c
from the Novena U-Boot fork (tag novena-r2) with two changes:
- Bank interleaving is disabled: The Novena U-Boot code disables it
unconditionally during execution anyway
- Page size is set to 1KB: I'm not sure the hardware supports x16 DIMMs
Mainline U-Boot has similar code, but the timing differences don't work
on my board so I'm unable to test or port that code over.
Signed-off-by: John Watts <contact@jookia.org>
---
arch/arm/boards/novena/ddr_regs.h | 119 ++++++++++++++++++++++++++++++
arch/arm/boards/novena/lowlevel.c | 9 +++
2 files changed, 128 insertions(+)
create mode 100644 arch/arm/boards/novena/ddr_regs.h
diff --git a/arch/arm/boards/novena/ddr_regs.h b/arch/arm/boards/novena/ddr_regs.h
new file mode 100644
index 0000000000..5f18d5e0e4
--- /dev/null
+++ b/arch/arm/boards/novena/ddr_regs.h
@@ -0,0 +1,119 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/* SPDX-FileCopyrightText: 2014 Marek Vasut <marex@denx.de> */
+
+#ifndef NOVENA_DDR_REGS_H
+#define NOVENA_DDR_REGS_H
+
+/* MEMORY CONTROLLER CONFIGURATION */
+
+static struct mx6dq_iomux_ddr_regs novena_ddr_regs = {
+ /* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */
+ .dram_sdclk_0 = 0x00020038,
+ .dram_sdclk_1 = 0x00020038,
+ .dram_cas = 0x00000038,
+ .dram_ras = 0x00000038,
+ .dram_reset = 0x00000038,
+ /* SDCKE[0:1]: 100k pull-up */
+ .dram_sdcke0 = 0x00003000,
+ .dram_sdcke1 = 0x00003000,
+ /* SDBA2: pull-up disabled */
+ .dram_sdba2 = 0x00000000,
+ /* SDODT[0:1]: 100k pull-up, 40 ohm */
+ .dram_sdodt0 = 0x00000038,
+ .dram_sdodt1 = 0x00000038,
+ /* SDQS[0:7]: Differential input, 40 ohm */
+ .dram_sdqs0 = 0x00000038,
+ .dram_sdqs1 = 0x00000038,
+ .dram_sdqs2 = 0x00000038,
+ .dram_sdqs3 = 0x00000038,
+ .dram_sdqs4 = 0x00000038,
+ .dram_sdqs5 = 0x00000038,
+ .dram_sdqs6 = 0x00000038,
+ .dram_sdqs7 = 0x00000038,
+
+ /* DQM[0:7]: Differential input, 40 ohm */
+ .dram_dqm0 = 0x00000038,
+ .dram_dqm1 = 0x00000038,
+ .dram_dqm2 = 0x00000038,
+ .dram_dqm3 = 0x00000038,
+ .dram_dqm4 = 0x00000038,
+ .dram_dqm5 = 0x00000038,
+ .dram_dqm6 = 0x00000038,
+ .dram_dqm7 = 0x00000038,
+};
+
+static struct mx6dq_iomux_grp_regs novena_grp_regs = {
+ /* DDR3 */
+ .grp_ddr_type = 0x000c0000,
+ .grp_ddrmode_ctl = 0x00020000,
+ /* Disable DDR pullups */
+ .grp_ddrpke = 0x00000000,
+ /* ADDR[00:16], SDBA[0:1]: 40 ohm */
+ .grp_addds = 0x00000038,
+ /* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */
+ .grp_ctlds = 0x00000038,
+ /* DATA[00:63]: Differential input, 40 ohm */
+ .grp_ddrmode = 0x00020000,
+ .grp_b0ds = 0x00000038,
+ .grp_b1ds = 0x00000038,
+ .grp_b2ds = 0x00000038,
+ .grp_b3ds = 0x00000038,
+ .grp_b4ds = 0x00000038,
+ .grp_b5ds = 0x00000038,
+ .grp_b6ds = 0x00000038,
+ .grp_b7ds = 0x00000038,
+};
+
+/* MEMORY STICK CONFIGURATION */
+
+static struct mx6_mmdc_calibration novena_mmdc_calib = {
+ /* write leveling calibration determine */
+ .p0_mpwldectrl0 = 0x00420048,
+ .p0_mpwldectrl1 = 0x006f0059,
+ .p1_mpwldectrl0 = 0x005a0104,
+ .p1_mpwldectrl1 = 0x01070113,
+ /* Read DQS Gating calibration */
+ .p0_mpdgctrl0 = 0x437c040b,
+ .p0_mpdgctrl1 = 0x0413040e,
+ .p1_mpdgctrl0 = 0x444f0446,
+ .p1_mpdgctrl1 = 0x044d0422,
+ /* Read Calibration: DQS delay relative to DQ read access */
+ .p0_mprddlctl = 0x4c424249,
+ .p1_mprddlctl = 0x4e48414f,
+ /* Write Calibration: DQ/DM delay relative to DQS write access */
+ .p0_mpwrdlctl = 0x42414641,
+ .p1_mpwrdlctl = 0x46374b43,
+};
+
+static struct mx6_ddr_sysinfo novena_ddr_info = {
+ /* Width of data bus: 0=16, 1=32, 2=64 */
+ .dsize = 2,
+ /* Config for full 4GB range so that get_mem_size() works */
+ .cs_density = 32, /* 32Gb per CS */
+ /* Single chip select */
+ .ncs = 1,
+ .cs1_mirror = 0,
+ .rtt_wr = 1, /* RTT_Wr = RZQ/4 */
+ .rtt_nom = 2, /* RTT_Nom = RZQ/2 */
+ .walat = 3, /* Write additional latency */
+ .ralat = 7, /* Read additional latency */
+ .mif3_mode = 3, /* Command prediction working mode */
+ .bi_on = 0, /* Bank interleaving disabled */
+ .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
+ .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
+};
+
+static struct mx6_ddr3_cfg novena_ddr_cfg = {
+ .mem_speed = 1600,
+ .density = 4,
+ .width = 64,
+ .banks = 8,
+ .rowaddr = 16,
+ .coladdr = 10,
+ .pagesz = 1,
+ .trcd = 1300,
+ .trcmin = 4900,
+ .trasmin = 3590,
+};
+
+#endif
diff --git a/arch/arm/boards/novena/lowlevel.c b/arch/arm/boards/novena/lowlevel.c
index 855855c6b9..ee71d9edd6 100644
--- a/arch/arm/boards/novena/lowlevel.c
+++ b/arch/arm/boards/novena/lowlevel.c
@@ -7,9 +7,11 @@
#include <mach/esdctl.h>
#include <mach/generic.h>
#include <mach/imx6.h>
+#include <mach/imx6-mmdc.h>
#include <mach/iomux-mx6.h>
#include <mach/xload.h>
#include <soc/fsl/fsl_udc.h>
+#include "ddr_regs.h"
#define MX6_OCRAM_BASE_ADDR 0x00900000
#define STACK_TOP (MX6_OCRAM_BASE_ADDR + SZ_128K)
@@ -31,6 +33,12 @@ static void setup_uart(void)
pr_debug(">");
}
+static void setup_ram(void)
+{
+ mx6dq_dram_iocfg(64, &novena_ddr_regs, &novena_grp_regs);
+ mx6_dram_cfg(&novena_ddr_info, &novena_mmdc_calib, &novena_ddr_cfg);
+}
+
static void load_barebox(void)
{
enum bootsource bootsrc;
@@ -66,6 +74,7 @@ ENTRY_FUNCTION_WITHSTACK(start_imx6q_novena, STACK_TOP, r0, r1, r2)
if (!running_from_ram()) {
imx6_ungate_all_peripherals();
setup_uart();
+ setup_ram();
load_barebox();
} else {
boot_barebox();
--
2.39.0
next prev parent reply other threads:[~2023-01-22 17:53 UTC|newest]
Thread overview: 52+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-01-22 17:51 [PATCH 0/5] Add support for the Kosagi Novena board John Watts
2023-01-22 17:51 ` [PATCH 1/5] ARM: novena: Add " John Watts
2023-01-23 9:20 ` Sascha Hauer
2023-01-22 17:51 ` John Watts [this message]
2023-01-22 17:51 ` [PATCH 3/5] ARM: novena: Require the PFUZE regulator John Watts
2023-01-22 17:51 ` [PATCH 4/5] ARM: novena: Read Ethernet MAC address from EEPROM John Watts
2023-01-23 9:33 ` Sascha Hauer
2023-01-23 9:55 ` John Watts
2023-01-24 18:35 ` John Watts
2023-01-25 8:04 ` Sascha Hauer
2023-01-25 8:11 ` John Watts
2023-01-25 8:19 ` Sascha Hauer
2023-01-25 13:31 ` John Watts
2023-01-25 13:48 ` Ahmad Fatoum
2023-01-25 14:04 ` John Watts
2023-01-25 14:16 ` Ahmad Fatoum
2023-01-25 14:28 ` John Watts
2023-01-25 14:33 ` Ahmad Fatoum
2023-01-25 14:50 ` John Watts
2023-01-25 15:42 ` Sascha Hauer
2023-01-25 16:13 ` John Watts
2023-01-22 17:51 ` [PATCH 5/5] ARM: novena: Use DDR3 information from SPD EEPROM John Watts
2023-01-22 23:20 ` John Watts
2023-01-25 16:42 ` [PATCH v2 0/4] Add support for the Kosagi Novena board John Watts
2023-01-25 16:42 ` [PATCH v2 1/4] ARM: novena: Add " John Watts
2023-01-25 19:33 ` Marco Felsch
2023-01-26 7:25 ` Sascha Hauer
2023-01-26 7:50 ` John Watts
2023-01-26 9:13 ` Marco Felsch
2023-01-25 16:42 ` [PATCH v2 2/4] ARM: novena: Setup RAM using static configuration John Watts
2023-01-25 19:39 ` Marco Felsch
2023-01-26 7:54 ` John Watts
2023-01-26 8:11 ` Sascha Hauer
2023-01-26 9:14 ` Marco Felsch
2023-01-25 16:42 ` [PATCH v2 3/4] ARM: novena: Read Ethernet MAC address from EEPROM John Watts
2023-01-25 20:07 ` Marco Felsch
2023-01-26 8:05 ` John Watts
2023-01-26 9:07 ` Marco Felsch
2023-01-25 16:42 ` [PATCH v2 4/4] ARM: novena: Use DDR3 information from SPD EEPROM John Watts
2023-01-29 23:27 ` [PATCH v3 0/4] Add support for the Kosagi Novena board John Watts
2023-01-29 23:27 ` [PATCH v3 1/4] ARM: novena: Add " John Watts
2023-01-30 20:13 ` Marco Felsch
2023-01-30 20:26 ` John Watts
2023-01-31 9:45 ` Marco Felsch
2023-01-29 23:27 ` [PATCH v3 2/4] ARM: novena: Setup RAM using static configuration John Watts
2023-01-29 23:27 ` [PATCH v3 3/4] ARM: novena: Read Ethernet MAC address from EEPROM John Watts
2023-01-30 20:04 ` Marco Felsch
2023-01-30 20:25 ` John Watts
2023-01-31 9:29 ` Marco Felsch
2023-01-29 23:28 ` [PATCH v3 4/4] ARM: novena: Use DDR3 information from SPD EEPROM John Watts
2023-01-30 20:18 ` Marco Felsch
2023-01-30 20:41 ` John Watts
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230122175141.119834-3-contact@jookia.org \
--to=contact@jookia.org \
--cc=barebox@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox