mail archive of the barebox mailing list
 help / color / mirror / Atom feed
From: Sascha Hauer <sha@pengutronix.de>
To: Ahmad Fatoum <a.fatoum@pengutronix.de>
Cc: barebox@lists.infradead.org
Subject: Re: [PATCH] ARM: i.MX8MM: innocomm-wb15: use revised PMIC settings
Date: Tue, 31 Jan 2023 09:20:37 +0100	[thread overview]
Message-ID: <20230131082037.GA13319@pengutronix.de> (raw)
In-Reply-To: <20230130072157.34711-1-a.fatoum@pengutronix.de>

On Mon, Jan 30, 2023 at 08:21:57AM +0100, Ahmad Fatoum wrote:
> Original values used when WB15 support was upstreamed were taken from
> EVK, but original U-Boot port, we had been running for years now, is
> configured differently and is known to be stable. Revert to those values.
> 
> Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
> ---
>  .../arm/boards/innocomm-imx8mm-wb15/lowlevel.c | 18 ++++++++++++++----
>  1 file changed, 14 insertions(+), 4 deletions(-)

Applied, thanks

Sascha

> 
> diff --git a/arch/arm/boards/innocomm-imx8mm-wb15/lowlevel.c b/arch/arm/boards/innocomm-imx8mm-wb15/lowlevel.c
> index 2077d3c88eb2..f7753bd32671 100644
> --- a/arch/arm/boards/innocomm-imx8mm-wb15/lowlevel.c
> +++ b/arch/arm/boards/innocomm-imx8mm-wb15/lowlevel.c
> @@ -35,14 +35,24 @@ static void setup_uart(void)
>  }
>  
>  static struct pmic_config bd71837_cfg[] = {
> +	/* unlock the PMIC regs */
> +	{ BD718XX_REGLOCK, 0x0 },
> +	/* retry powering up indefinitely every 250ms after VR fault */
> +	{ BD718XX_RCVCFG, 0xfc },
>  	/* decrease RESET key long push time from the default 10s to 10ms */
>  	{ BD718XX_PWRONCONFIG1, 0x0 },
> -	/* unlock the PMIC regs */
> -	{ BD718XX_REGLOCK, 0x1 },
> +	/* WDOG_B: Warm Reset */
> +	{ BD718XX_PWRCTRL0, 0xa3 },
> +	/* READY=>SNVS on PMIC_ON_REQ, SNVS=>RUN on VSYS_UVLO */
> +	{ BD718XX_TRANS_COND0, 0x48 },
> +	/* WDOG_B: Go to SNVS power state after deassert */
> +	{ BD718XX_TRANS_COND1, 0xc0 },
>  	/* Set VDD_SOC/VDD_DRAM to typical value 0.85v for nominal mode */
>  	{ BD718XX_BUCK1_VOLT_RUN, 0xf },
> -	/* increase VDD_DRAM to 0.975v for 3Ghz DDR */
> -	{ BD718XX_1ST_NODVS_BUCK_VOLT, 0x83 },
> +	/* increase VDD_DRAM to 0.900v for 2400MT/s DDR */
> +	{ BD718XX_1ST_NODVS_BUCK_VOLT, 0x02 },
> +	/* set BUCK8 to 1.10v */
> +	{ BD718XX_4TH_NODVS_BUCK_VOLT, 0x1e },
>  	/* lock the PMIC regs */
>  	{ BD718XX_REGLOCK, 0x11 },
>  };
> -- 
> 2.30.2
> 
> 
> 

-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |



      reply	other threads:[~2023-01-31  8:21 UTC|newest]

Thread overview: 2+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-01-30  7:21 Ahmad Fatoum
2023-01-31  8:20 ` Sascha Hauer [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20230131082037.GA13319@pengutronix.de \
    --to=sha@pengutronix.de \
    --cc=a.fatoum@pengutronix.de \
    --cc=barebox@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox