mail archive of the barebox mailing list
 help / color / mirror / Atom feed
From: Sascha Hauer <sha@pengutronix.de>
To: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: barebox@lists.infradead.org, Oleksij Rempel <linux@rempel-privat.de>
Subject: Re: [PATCH v1] net: phy: add TI DP83TG720 1000BaseT1 PHY support
Date: Wed, 13 Dec 2023 07:52:43 +0100	[thread overview]
Message-ID: <20231213065243.GI1318922@pengutronix.de> (raw)
In-Reply-To: <20231206111118.1338567-1-o.rempel@pengutronix.de>

On Wed, Dec 06, 2023 at 12:11:18PM +0100, Oleksij Rempel wrote:
> From: Oleksij Rempel <linux@rempel-privat.de>
> 
> Add driver for TI DP83TG720 driver support.
> 
> Even if the PHY is capable of creating a link on it's own. It needs
> proper RGMII configuration and HW reset on link loss.
> 
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  drivers/net/phy/Kconfig     |   6 +++
>  drivers/net/phy/Makefile    |   1 +
>  drivers/net/phy/dp83tg720.c | 102 ++++++++++++++++++++++++++++++++++++
>  3 files changed, 109 insertions(+)
>  create mode 100644 drivers/net/phy/dp83tg720.c

Applied, thanks

Sascha

> 
> diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
> index e95e2a3228..8e12671801 100644
> --- a/drivers/net/phy/Kconfig
> +++ b/drivers/net/phy/Kconfig
> @@ -35,6 +35,12 @@ config DP83TD510_PHY
>  	  Support for the DP83TD510 Ethernet 10Base-T1L PHY. This PHY supports
>  	  a 10M single pair Ethernet connection for up to 1000 meter cable.
>  
> +config DP83TG720_PHY
> +	tristate "Texas Instruments DP83TG720 Ethernet 1000Base-T1 PHY"
> +	help
> +	  Support for the DP83TG720 Ethernet 10000Base-T1 PHY. This PHY supports
> +	  a 1000M single pair Ethernet.
> +
>  config LXT_PHY
>  	bool "Driver for the Intel LXT PHYs"
>  	help
> diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
> index 26e4ad884d..ce15e1bab7 100644
> --- a/drivers/net/phy/Makefile
> +++ b/drivers/net/phy/Makefile
> @@ -19,4 +19,5 @@ obj-$(CONFIG_MDIO_BUS_MUX)	+= mdio-mux.o
>  obj-$(CONFIG_MDIO_BUS_MUX_GPIO)	+= mdio-mux-gpio.o
>  obj-$(CONFIG_DP83867_PHY)	+= dp83867.o
>  obj-$(CONFIG_DP83TD510_PHY)	+= dp83td510.o
> +obj-$(CONFIG_DP83TG720_PHY)	+= dp83tg720.o
>  
> diff --git a/drivers/net/phy/dp83tg720.c b/drivers/net/phy/dp83tg720.c
> new file mode 100644
> index 0000000000..f0c6e29489
> --- /dev/null
> +++ b/drivers/net/phy/dp83tg720.c
> @@ -0,0 +1,102 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/* Driver for the Texas Instruments DP83TG720 PHY
> + * Copyright (c) 2023 Pengutronix, Oleksij Rempel <kernel@pengutronix.de>
> + */
> +#include <common.h>
> +#include <linux/mdio.h>
> +#include <linux/phy.h>
> +
> +#define DP83TG720S_PHY_ID			0x2000a284
> +
> +/* MDIO_MMD_VEND2 registers */
> +#define DP83TG720S_MII_REG_10			0x10
> +#define DP83TG720S_LINK_STATUS			BIT(0)
> +
> +#define DP83TG720S_RGMII_DELAY_CTRL		0x602
> +/* In RGMII mode, Enable or disable the internal delay for RXD */
> +#define DP83TG720S_RGMII_RX_CLK_SEL		BIT(1)
> +/* In RGMII mode, Enable or disable the internal delay for TXD */
> +#define DP83TG720S_RGMII_TX_CLK_SEL		BIT(0)
> +
> +#define DP83TG720S_PHY_RESET			0x1f
> +#define DP83TG720S_HW_RESET			BIT(15)
> +
> +static int dp83tg720_config_rgmii_delay(struct phy_device *phydev)
> +{
> +	u16 rgmii_delay_mask;
> +	u16 rgmii_delay = 0;
> +
> +	switch (phydev->interface) {
> +	case PHY_INTERFACE_MODE_RGMII:
> +		rgmii_delay = 0;
> +		break;
> +	case PHY_INTERFACE_MODE_RGMII_ID:
> +		rgmii_delay = DP83TG720S_RGMII_RX_CLK_SEL |
> +				DP83TG720S_RGMII_TX_CLK_SEL;
> +		break;
> +	case PHY_INTERFACE_MODE_RGMII_RXID:
> +		rgmii_delay = DP83TG720S_RGMII_RX_CLK_SEL;
> +		break;
> +	case PHY_INTERFACE_MODE_RGMII_TXID:
> +		rgmii_delay = DP83TG720S_RGMII_TX_CLK_SEL;
> +		break;
> +	default:
> +		return 0;
> +	}
> +
> +	rgmii_delay_mask = DP83TG720S_RGMII_RX_CLK_SEL |
> +			   DP83TG720S_RGMII_TX_CLK_SEL;
> +
> +	return phy_modify_mmd(phydev, MDIO_MMD_VEND2,
> +			      DP83TG720S_RGMII_DELAY_CTRL, rgmii_delay_mask,
> +			      rgmii_delay);
> +}
> +
> +static int dp83tg720_phy_init(struct phy_device *phydev)
> +{
> +	/* HW reset is needed to recover link if previous link was lost. SW
> +	 * reset is not enough.
> +	 */
> +	phy_write(phydev, DP83TG720S_PHY_RESET, DP83TG720S_HW_RESET);
> +
> +	phydev->supported = SUPPORTED_1000baseT_Full;
> +	phydev->advertising = SUPPORTED_1000baseT_Full;
> +
> +	if (phy_interface_is_rgmii(phydev))
> +		return dp83tg720_config_rgmii_delay(phydev);
> +
> +	return 0;
> +}
> +
> +static int dp83tg720_read_status(struct phy_device *phydev)
> +{
> +	u16 phy_sts;
> +
> +	phy_sts = phy_read(phydev, DP83TG720S_MII_REG_10);
> +	phydev->link = !!(phy_sts & DP83TG720S_LINK_STATUS);
> +	if (!phydev->link) {
> +		phydev->speed = SPEED_UNKNOWN;
> +		phydev->duplex = DUPLEX_UNKNOWN;
> +
> +		/* According to the "DP83TC81x, DP83TG72x Software
> +		 * Implementation Guide", the PHY needs to be reset after a
> +		 * link loss or if no link is created after at least 100ms.
> +		 */
> +		dp83tg720_phy_init(phydev);
> +		return 0;
> +	}
> +
> +	phydev->duplex = DUPLEX_FULL;
> +	phydev->speed = SPEED_1000;
> +
> +	return 0;
> +}
> +
> +static struct phy_driver dp83tg720_driver[] = {
> +{
> +	PHY_ID_MATCH_MODEL(DP83TG720S_PHY_ID),
> +	.drv.name	= "TI DP83TG720S",
> +	.read_status	= dp83tg720_read_status,
> +	.config_init	= dp83tg720_phy_init,
> +} };
> +device_phy_drivers(dp83tg720_driver);
> -- 
> 2.39.2
> 
> 
> 

-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |



      reply	other threads:[~2023-12-13  6:53 UTC|newest]

Thread overview: 2+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-12-06 11:11 Oleksij Rempel
2023-12-13  6:52 ` Sascha Hauer [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20231213065243.GI1318922@pengutronix.de \
    --to=sha@pengutronix.de \
    --cc=barebox@lists.infradead.org \
    --cc=linux@rempel-privat.de \
    --cc=o.rempel@pengutronix.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox