From: David Picard <david.picard@clermont.in2p3.fr>
To: Sascha Hauer <s.hauer@pengutronix.de>,
BAREBOX <barebox@lists.infradead.org>
Cc: David Picard <david.picard@clermont.in2p3.fr>,
Ahmad Fatoum <ahmad@a3f.at>,
Ahmad Fatoum <a.fatoum@pengutronix.de>
Subject: [PATCH 00/11] ARM: boards: add support for Enclustra Mercury SA2
Date: Wed, 17 Sep 2025 17:22:03 +0200 [thread overview]
Message-ID: <20250917-boards-enclustra-sa2-add-support-v1-0-2de8f69107a1@clermont.in2p3.fr> (raw)
Add support for the Enclustra Mercury+ SA2, a Cyclone V based
SoC FPGA.
https://www.enclustra.com/en/products/system-on-chip-modules/mercury-sa2/
The SoM provides a 64MiB NOR QSPI flash, DDR3, Ethernet PHY, RTC.
The Cyclone V features a hardware ARM core (aka HPS) that can boot
from SD card (MMC), QSPI flash. This patch series focusses on MMC.
Signed-off-by: David Picard <david.picard@clermont.in2p3.fr>
---
Ahmad Fatoum (3):
ARM: dts: socfpga: use upstream SA2 device tree
gpio: dw: support numbering via aliases
gpio: dw: make deep probe compatible
David Picard (8):
Add handoff files
Add Enclustra Mercury+ SA2 module
Add Enclustra devicetree files
ARM: dts: socfpga: adapt upstream SA2 device tree
boards: enclustra-sa2: read MAC address from EEPROM
boards: enclustra-sa2: enable bridges
boards: enclustra-sa2: configure SI5338
boards: enclustra-sa2: enable SI5338
arch/arm/boards/Makefile | 1 +
arch/arm/boards/enclustra-sa2/Makefile | 2 +
.../boards/enclustra-sa2/Si5338-RevB-Registers.h | 433 +++++++++++++
arch/arm/boards/enclustra-sa2/atsha204a.c | 436 +++++++++++++
arch/arm/boards/enclustra-sa2/atsha204a.h | 19 +
arch/arm/boards/enclustra-sa2/board.c | 83 +++
arch/arm/boards/enclustra-sa2/crc16.c | 65 ++
arch/arm/boards/enclustra-sa2/crc16.h | 28 +
.../boards/enclustra-sa2/iocsr_config_cyclone5.c | 678 +++++++++++++++++++++
arch/arm/boards/enclustra-sa2/lowlevel.c | 13 +
arch/arm/boards/enclustra-sa2/pinmux_config.c | 241 ++++++++
arch/arm/boards/enclustra-sa2/pll_config.h | 107 ++++
arch/arm/boards/enclustra-sa2/sdram_config.h | 112 ++++
arch/arm/boards/enclustra-sa2/sequencer_auto.h | 225 +++++++
.../boards/enclustra-sa2/sequencer_auto_ac_init.c | 67 ++
.../enclustra-sa2/sequencer_auto_inst_init.c | 158 +++++
arch/arm/boards/enclustra-sa2/sequencer_defines.h | 165 +++++
arch/arm/boards/enclustra-sa2/si5338_config.c | 326 ++++++++++
arch/arm/boards/enclustra-sa2/si5338_config.h | 22 +
arch/arm/configs/socfpga-xload_defconfig | 1 +
arch/arm/configs/socfpga_defconfig | 3 +-
arch/arm/dts/Makefile | 1 +
arch/arm/dts/socfpga_cyclone5_mercury_sa2.dts | 17 +
arch/arm/dts/socfpga_cyclone5_mercury_sa2.dtsi | 187 ++++++
arch/arm/mach-socfpga/Kconfig | 9 +
drivers/gpio/Kconfig | 1 +
drivers/gpio/gpio-dw.c | 48 +-
images/Makefile.socfpga | 8 +
28 files changed, 3434 insertions(+), 22 deletions(-)
---
base-commit: 89bf1fcc998fc5fea0ce613d9930dd9ee39c0fb2
change-id: 20250916-boards-enclustra-sa2-add-support-4704233a6861
Best regards,
--
David Picard <david.picard@clermont.in2p3.fr>
next reply other threads:[~2025-09-17 15:52 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-09-17 15:22 David Picard [this message]
2025-09-17 15:22 ` [PATCH 01/11] Add handoff files David Picard
2025-09-17 15:22 ` [PATCH 02/11] Add Enclustra Mercury+ SA2 module David Picard
2025-09-18 6:21 ` Sascha Hauer
2025-09-17 15:22 ` [PATCH 03/11] Add Enclustra devicetree files David Picard
2025-09-17 15:22 ` [PATCH 04/11] ARM: dts: socfpga: use upstream SA2 device tree David Picard
2025-09-18 6:32 ` Sascha Hauer
2025-09-18 10:09 ` David Picard
2025-09-18 10:20 ` Ahmad Fatoum
2025-09-17 15:22 ` [PATCH 05/11] ARM: dts: socfpga: adapt " David Picard
2025-09-17 15:22 ` [PATCH 06/11] boards: enclustra-sa2: read MAC address from EEPROM David Picard
2025-09-17 17:06 ` Alexander Shiyan
2025-09-18 6:18 ` Sascha Hauer
2025-09-18 14:01 ` David Picard
2025-09-18 14:12 ` Sascha Hauer
2025-09-18 15:07 ` David Picard
2025-09-22 13:15 ` Sascha Hauer
2025-09-23 9:07 ` David Picard
2025-09-23 9:40 ` Sascha Hauer
2025-09-23 11:50 ` David Picard
2025-09-23 15:31 ` David Picard
2025-09-17 15:22 ` [PATCH 07/11] gpio: dw: support numbering via aliases David Picard
2025-09-18 6:35 ` Sascha Hauer
2025-09-17 15:22 ` [PATCH 08/11] gpio: dw: make deep probe compatible David Picard
2025-09-17 15:22 ` [PATCH 09/11] boards: enclustra-sa2: enable bridges David Picard
2025-09-18 6:37 ` Sascha Hauer
2025-09-17 15:22 ` [PATCH 10/11] boards: enclustra-sa2: configure SI5338 David Picard
2025-09-18 7:09 ` Sascha Hauer
2025-09-18 13:23 ` David Picard
2025-09-17 15:22 ` [PATCH 11/11] boards: enclustra-sa2: enable SI5338 David Picard
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250917-boards-enclustra-sa2-add-support-v1-0-2de8f69107a1@clermont.in2p3.fr \
--to=david.picard@clermont.in2p3.fr \
--cc=a.fatoum@pengutronix.de \
--cc=ahmad@a3f.at \
--cc=barebox@lists.infradead.org \
--cc=s.hauer@pengutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox