mail archive of the barebox mailing list
 help / color / mirror / Atom feed
From: Ahmad Fatoum <a.fatoum@pengutronix.de>
To: Antony Pavlov <antonynpavlov@gmail.com>
Cc: barebox@lists.infradead.org, rcz@pengutronix.de
Subject: Re: [PATCH v2 14/20] RISC-V: erizo: migrate to PBL
Date: Tue, 16 Mar 2021 19:38:48 +0100	[thread overview]
Message-ID: <33c77bd7-e4c3-e258-b47b-84bdce1c00ee@pengutronix.de> (raw)
In-Reply-To: <20210316171221.d9f38875021a468efdf41dc5@gmail.com>

Hello Antony,

On 16.03.21 15:12, Antony Pavlov wrote:
> On Tue, 16 Mar 2021 09:04:59 +0100
> Ahmad Fatoum <a.fatoum@pengutronix.de> wrote:
> 
>> We now have everything in place to migrate erizo to PBL.
>> As currently, this is the only board, we can drop all non-PBL support
>> in the same go.
>>
>> The board still throws TLSF errors on startup, but that was the case
>> before the rework as well. Tested with qemu as described in the docs.
>>
>> Cc: Antony Pavlov <antonynpavlov@gmail.com>
>> Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
>> ---
>> I assume some memory corruption is happening due to the minimal malloc
>> area size?
> 
> There is no problem with 1M malloc area size.
> 
> I succesfully run virt64_defconfig barebox with CONFIG_MALLOC_SIZE=0x100000 and CONFIG_DISK=n.
> 
> Moreover, it's possible to run very minimum mips barebox with 128K tlfs malloc area.
> 
> I suppose I can make bisection after rebuild old fashion rv32 toolchain
> (alas! 3 year old rv32 toolchain binaries do not work on my current Debian configuration).

I used riscv64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110 for everything.
barebox already takes care to pass the correct options to build for 32-bit.

> 
>> It doesn't happen with dlmalloc. It doesn't happen on riscv
>> virt added later on, so I will likely not pursue this further.
>> ---
>>  Documentation/boards/riscv.rst             | 13 +++--
>>  Makefile                                   |  1 +
>>  arch/riscv/Kconfig                         | 15 ++---
>>  arch/riscv/Makefile                        | 25 +++-----
>>  arch/riscv/boards/erizo/Makefile           |  4 +-
>>  arch/riscv/boards/erizo/board.c            | 25 --------
>>  arch/riscv/boards/erizo/lowlevel.c         | 37 ++++--------
>>  arch/riscv/boards/erizo/start.S            | 68 ----------------------
>>  arch/riscv/configs/erizo_generic_defconfig |  5 --
>>  arch/riscv/dts/Makefile                    |  9 +--
>>  arch/riscv/lib/Makefile                    |  2 +-
>>  arch/riscv/lib/barebox.lds.S               | 36 ++++++++----
>>  arch/riscv/lib/dtb.c                       | 26 +++++++++
>>  common/Kconfig                             |  4 +-
>>  images/Makefile                            |  4 ++
>>  images/Makefile.riscv                      | 12 ++++
>>  pbl/Kconfig                                |  2 +-
>>  17 files changed, 107 insertions(+), 181 deletions(-)
>>  delete mode 100644 arch/riscv/boards/erizo/board.c
>>  delete mode 100644 arch/riscv/boards/erizo/start.S
>>  create mode 100644 arch/riscv/lib/dtb.c
>>  create mode 100644 images/Makefile.riscv
>>
>> diff --git a/Documentation/boards/riscv.rst b/Documentation/boards/riscv.rst
>> index c7fa52aadbee..a1f7e30531ee 100644
>> --- a/Documentation/boards/riscv.rst
>> +++ b/Documentation/boards/riscv.rst
>> @@ -1,8 +1,11 @@
>>  RISC-V
>>  ======
>>  
>> -Running RISC-V barebox on qemu
>> -------------------------------
>> +Erizo
>> +-----
>> +
>> +Running on qemu
>> +~~~~~~~~~~~~~~~
>>  
>>  Obtain RISC-V GCC/Newlib Toolchain,
>>  see https://github.com/riscv/riscv-tools/blob/master/README.md
>> @@ -44,7 +47,7 @@ Next compile barebox::
>>  Run barebox::
>>  
>>    $ <path to riscv-qemu source>/riscv32-softmmu/qemu-system-riscv32 \
>> -      -nographic -M erizo -bios <path to barebox sources >/barebox.bin \
>> +      -nographic -M erizo -bios ./images/barebox-erizo-generic.img \
>>        -serial stdio -monitor none -trace file=/dev/null
>>    Switch to console [cs0]
>>    
>> @@ -59,8 +62,8 @@ Run barebox::
>>    barebox:/
>>  
>>  
>> -Running RISC-V barebox on DE0-Nano FPGA board
>> ----------------------------------------------
>> +Running on DE0-Nano FPGA board
>> +------------------------------
>>  
>>  See https://github.com/open-design/riscv-soc-cores/ for instructions
>>  on DE0-Nano bitstream generation and loading.
>> diff --git a/Makefile b/Makefile
>> index 6d44314f0a7e..4cc7bef2bd42 100644
>> --- a/Makefile
>> +++ b/Makefile
>> @@ -776,6 +776,7 @@ define rule_barebox__
>>  	$(if $(CONFIG_KALLSYMS),,+$(call cmd,barebox_version))
>>  	$(call cmd,barebox__)
>>  	$(Q)echo 'cmd_$@ := $(cmd_barebox__)' > $(@D)/.$(@F).cmd
>> +	$(call cmd,prelink__)
>>  	$(call cmd,sysmap)
>>  endef
>>  
>> diff --git a/arch/riscv/Kconfig b/arch/riscv/Kconfig
>> index b1b24f2e5764..4a2a547a7b35 100644
>> --- a/arch/riscv/Kconfig
>> +++ b/arch/riscv/Kconfig
>> @@ -1,14 +1,16 @@
>>  config RISCV
>>  	def_bool y
>>  	select GENERIC_FIND_NEXT_BIT
>> -	select HAVE_CONFIGURABLE_MEMORY_LAYOUT
>> -	select HAVE_CONFIGURABLE_TEXT_BASE
>>  	select GPIOLIB
>>  	select OFTREE
>> +	select OFDEVICE
>>  	select COMMON_CLK
>>  	select COMMON_CLK_OF_PROVIDER
>>  	select CLKDEV_LOOKUP
>>  	select HAS_DMA
>> +	select HAVE_PBL_IMAGE
>> +	select HAVE_PBL_MULTI_IMAGES
>> +	select HAVE_IMAGE_COMPRESSION
>>  
>>  config ARCH_TEXT_BASE
>>  	hex
>> @@ -24,6 +26,7 @@ config MACH_ERIZO
>>  	bool "erizo family"
>>  	select HAS_DEBUG_LL
>>  	select HAS_NMON
>> +	select USE_COMPRESSED_DTB
>>  
>>  endchoice
>>  
>> @@ -56,14 +59,6 @@ config 32BIT
>>  
>>  endchoice
>>  
>> -config BUILTIN_DTB
>> -	bool "link a DTB into the barebox image"
>> -	depends on OFTREE
>> -
>> -config BUILTIN_DTB_NAME
>> -	string "DTB to build into the barebox image"
>> -	depends on BUILTIN_DTB
>> -
>>  source "arch/riscv/mach-erizo/Kconfig"
>>  
>>  endmenu
>> diff --git a/arch/riscv/Makefile b/arch/riscv/Makefile
>> index df2b5bb681a4..00456ed02ce1 100644
>> --- a/arch/riscv/Makefile
>> +++ b/arch/riscv/Makefile
>> @@ -3,21 +3,23 @@ KBUILD_DEFCONFIG := erizo_generic_defconfig
>>  KBUILD_CPPFLAGS += -fno-strict-aliasing
>>  
>>  ifeq ($(CONFIG_ARCH_RV32I),y)
>> -	cflags-y += -march=rv32im -mabi=ilp32
>> -	riscv-ldflags-y += -melf32lriscv
>> +	riscv-cflags-y := -march=rv32im -mabi=ilp32
>> +	riscv-ldflags-y := -melf32lriscv
>>  endif
>>  
>> -cflags-y += -fno-pic -Wstrict-prototypes -mcmodel=medany
>> +riscv-cflags-y += -Wstrict-prototypes -mcmodel=medany -fpic
>> +riscv-ldflags-y += -pie -static
>>  
>> +PBL_CPPFLAGS += $(riscv-cflags-y)
>> +LDFLAGS_pbl += $(riscv-ldflags-y)
>> +
>> +cflags-y += $(riscv-cflags-y)
>>  LDFLAGS_barebox += -nostdlib
>>  
>>  machine-$(CONFIG_MACH_ERIZO)	:= erizo
>>  
>>  LDFLAGS_barebox += $(riscv-ldflags-y)
>>  
>> -TEXT_BASE = $(CONFIG_TEXT_BASE)
>> -KBUILD_CPPFLAGS += -DTEXT_BASE=$(CONFIG_TEXT_BASE)
>> -
>>  ifndef CONFIG_MODULES
>>  # Add cleanup flags
>>  KBUILD_CPPFLAGS += -fdata-sections -ffunction-sections
>> @@ -54,13 +56,4 @@ lds-y	:= arch/riscv/lib/barebox.lds
>>  
>>  CLEAN_FILES += arch/riscv/lib/barebox.lds
>>  
>> -ifeq ($(CONFIG_MACH_ERIZO),y)
>> -KBUILD_IMAGE := barebox.erizo.nmon
>> -endif
>> -
>> -quiet_cmd_erizo_nmon_image = MKIMAGE $@
>> -      cmd_erizo_nmon_image = $(srctree)/scripts/erizo-nmon-image $< $@ || \
>> -	echo "WARNING: Couldn't create erizo nmon image due to previous errors."
>> -
>> -barebox.erizo.nmon: $(KBUILD_BINARY) FORCE
>> -	$(call if_changed,erizo_nmon_image)
>> +KBUILD_IMAGE := $(KBUILD_BINARY)
>> diff --git a/arch/riscv/boards/erizo/Makefile b/arch/riscv/boards/erizo/Makefile
>> index 72b9a13ba73f..3d217ffe0b93 100644
>> --- a/arch/riscv/boards/erizo/Makefile
>> +++ b/arch/riscv/boards/erizo/Makefile
>> @@ -1,5 +1,3 @@
>>  # SPDX-License-Identifier: GPL-2.0
>>  
>> -obj-y += lowlevel.o
>> -obj-y += start.o
>> -obj-y += board.o
>> +pbl-y += lowlevel.o
>> diff --git a/arch/riscv/boards/erizo/board.c b/arch/riscv/boards/erizo/board.c
>> deleted file mode 100644
>> index b9b68fc7f254..000000000000
>> --- a/arch/riscv/boards/erizo/board.c
>> +++ /dev/null
>> @@ -1,25 +0,0 @@
>> -// SPDX-License-Identifier: GPL-2.0-only
>> -/*
>> - * Copyright (C) 2016, 2018 Antony Pavlov <antonynpavlov@gmail.com>
>> - *
>> - * This file is part of barebox.
>> - *
>> - * This program is distributed in the hope that it will be useful,
>> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> - * GNU General Public License for more details.
>> - *
>> - */
>> -#include <common.h>
>> -#include <init.h>
>> -#include <of.h>
>> -
>> -extern char __dtb_start[];
>> -
>> -static int of_riscv_init(void)
>> -{
>> -	barebox_register_fdt(__dtb_start);
>> -
>> -	return 0;
>> -}
>> -core_initcall(of_riscv_init);
>> diff --git a/arch/riscv/boards/erizo/lowlevel.c b/arch/riscv/boards/erizo/lowlevel.c
>> index f9c640c1123f..d9edb530b746 100644
>> --- a/arch/riscv/boards/erizo/lowlevel.c
>> +++ b/arch/riscv/boards/erizo/lowlevel.c
>> @@ -1,35 +1,18 @@
>>  // SPDX-License-Identifier: GPL-2.0-only
>> -/*
>> - * Copyright (C) 2016 Antony Pavlov <antonynpavlov@gmail.com>
>> - *
>> - * This file is part of barebox.
>> - *
>> - * This program is distributed in the hope that it will be useful,
>> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> - * GNU General Public License for more details.
>> - *
>> - */
>>  
>>  #include <common.h>
>> -#include <memory.h>
>> -#include <asm-generic/memory_layout.h>
>> -#include <asm/sections.h>
>> +#include <asm/barebox-riscv.h>
>> +#include <debug_ll.h>
>>  
>> -void main_entry(void);
>> -
>> -/**
>> - * Called plainly from assembler code
>> - *
>> - * @note The C environment isn't initialized yet
>> - */
>> -void main_entry(void)
>> +ENTRY_FUNCTION(start_erizo_generic, a0, a1, a2)
>>  {
>> -	/* clear the BSS first */
>> -	memset(__bss_start, 0x00, __bss_stop - __bss_start);
>> +	extern char __dtb_z_erizo_generic_start[];
>> +
>> +	debug_ll_ns16550_init();
>> +	putc_ll('>');
>>  
>> -	mem_malloc_init((void *)MALLOC_BASE,
>> -			(void *)(MALLOC_BASE + MALLOC_SIZE - 1));
>> +	/* On POR, we are running from read-only memory here. */
>>  
>> -	start_barebox();
>> +	barebox_riscv_entry(0x80000000, SZ_8M,
>> +			    __dtb_z_erizo_generic_start + get_runtime_offset());
>>  }
>> diff --git a/arch/riscv/boards/erizo/start.S b/arch/riscv/boards/erizo/start.S
>> deleted file mode 100644
>> index d1dbe48b7bd6..000000000000
>> --- a/arch/riscv/boards/erizo/start.S
>> +++ /dev/null
>> @@ -1,68 +0,0 @@
>> -/* SPDX-License-Identifier: GPL-2.0-only */
>> -/*
>> - * Startup Code for RISC-V CPU
>> - *
>> - * Copyright (C) 2016 Antony Pavlov <antonynpavlov@gmail.com>
>> - *
>> - * based on coreboot/src/arch/riscv/bootblock.S
>> - *      and barebox/arch/mips/boot/start.S
>> - *
>> - * This file is part of barebox.
>> - *
>> - * This program is distributed in the hope that it will be useful,
>> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> - * GNU General Public License for more details.
>> - *
>> - */
>> -
>> -#include <asm-generic/memory_layout.h>
>> -
>> -#include "mach/debug_ll.h"
>> -
>> -#include "asm/riscv_nmon.h"
>> -
>> -	.text
>> -	.section ".text_entry"
>> -	.align 2
>> -
>> -.globl _start
>> -_start:
>> -	debug_ll_ns16550_init
>> -
>> -	riscv_nmon
>> -
>> -	li	sp, STACK_BASE + STACK_SIZE
>> -
>> -	/* copy barebox to link location */
>> -
>> -	la	a0, _start	/* a0 <- _start actual address */
>> -	li	a1, CONFIG_TEXT_BASE	/* a1 <- _start link address */
>> -
>> -	beq	a0, a1, main_entry
>> -
>> -	la	a2, __bss_start
>> -
>> -#define LONGSIZE 4
>> -
>> -copy_loop:
>> -	/* copy from source address [a0] */
>> -	lw	t0, LONGSIZE * 0(a0)
>> -	lw	t1, LONGSIZE * 1(a0)
>> -	lw	t2, LONGSIZE * 2(a0)
>> -	lw	t3, LONGSIZE * 3(a0)
>> -	/* copy to target address [a1] */
>> -	sw	t0, LONGSIZE * 0(a1)
>> -	sw	t1, LONGSIZE * 1(a1)
>> -	sw	t2, LONGSIZE * 2(a1)
>> -	sw	t3, LONGSIZE * 3(a1)
>> -	addi	a0, a0, LONGSIZE * 4
>> -	addi	a1, a1, LONGSIZE * 4
>> -	bgeu	a2, a0, copy_loop
>> -
>> -	/* Alas! At the moment I can't load main_entry __link__ address
>> -	   into a0 with la. Use CONFIG_TEXT_BASE instead. This solution
>> -	   leads to extra cycles for repeat sp initialization. */
>> -
>> -	li	a0, CONFIG_TEXT_BASE
>> -	jalr	a0
>> diff --git a/arch/riscv/configs/erizo_generic_defconfig b/arch/riscv/configs/erizo_generic_defconfig
>> index 2ea1e46cc960..839b652ab53d 100644
>> --- a/arch/riscv/configs/erizo_generic_defconfig
>> +++ b/arch/riscv/configs/erizo_generic_defconfig
>> @@ -1,9 +1,5 @@
>>  # CONFIG_GLOBALVAR is not set
>> -CONFIG_TEXT_BASE=0x80000000
>> -CONFIG_MEMORY_LAYOUT_FIXED=y
>> -CONFIG_STACK_BASE=0x800e0000
>>  CONFIG_STACK_SIZE=0x20000
>> -CONFIG_MALLOC_BASE=0x80100000
>>  CONFIG_MALLOC_SIZE=0x100000
>>  CONFIG_MALLOC_TLSF=y
>>  CONFIG_PANIC_HANG=y
>> @@ -36,7 +32,6 @@ CONFIG_CMD_SPI=y
>>  CONFIG_CMD_OF_DUMP=y
>>  CONFIG_CMD_TIME=y
>>  CONFIG_CMD_DHRYSTONE=y
>> -CONFIG_OFDEVICE=y
>>  CONFIG_DRIVER_SERIAL_NS16550=y
>>  CONFIG_DRIVER_SPI_GPIO=y
>>  CONFIG_I2C=y
>> diff --git a/arch/riscv/dts/Makefile b/arch/riscv/dts/Makefile
>> index 6bd4e5a9250c..4041c34e0c45 100644
>> --- a/arch/riscv/dts/Makefile
>> +++ b/arch/riscv/dts/Makefile
>> @@ -1,12 +1,9 @@
>> -BUILTIN_DTB := $(patsubst "%",%,$(CONFIG_BUILTIN_DTB_NAME))
>> -ifneq ($(BUILTIN_DTB),)
>> -obj-$(CONFIG_BUILTIN_DTB) += $(BUILTIN_DTB).dtb.o
>> -endif
>> -
>> -obj-$(CONFIG_BOARD_ERIZO_GENERIC) += erizo-generic.dtb.o
>> +# SPDX-License-Identifier: GPL-2.0
>>  
>>  # just to build a built-in.o. Otherwise compilation fails when no devicetree is
>>  # created.
>>  obj- += dummy.o
>>  
>> +pbl-$(CONFIG_BOARD_ERIZO_GENERIC) += erizo-generic.dtb.o
>> +
>>  clean-files := *.dtb *.dtb.S .*.dtc .*.pre .*.dts
>> diff --git a/arch/riscv/lib/Makefile b/arch/riscv/lib/Makefile
>> index 5f57d9fcd2e2..a9bf68bca597 100644
>> --- a/arch/riscv/lib/Makefile
>> +++ b/arch/riscv/lib/Makefile
>> @@ -2,7 +2,7 @@
>>  
>>  extra-y += barebox.lds
>>  
>> -obj-y += riscv_timer.o
>> +obj-y += riscv_timer.o dtb.o
>>  obj-pbl-y += sections.o setupc.o reloc.o sections.o runtime-offset.o
>>  obj-$(CONFIG_HAS_ARCH_SJLJ) += setjmp.o longjmp.o
>>  obj-$(CONFIG_RISCV_OPTIMZED_STRING_FUNCTIONS) += memcpy.o memset.o memmove.o
>> diff --git a/arch/riscv/lib/barebox.lds.S b/arch/riscv/lib/barebox.lds.S
>> index c8a331c577cf..562ad5dc6662 100644
>> --- a/arch/riscv/lib/barebox.lds.S
>> +++ b/arch/riscv/lib/barebox.lds.S
>> @@ -14,22 +14,30 @@
>>  #include <asm-generic/barebox.lds.h>
>>  
>>  OUTPUT_ARCH(riscv)
>> -ENTRY(_start)
>> +ENTRY(start)
>>  SECTIONS
>>  {
>> -	. = TEXT_BASE;
>> +	. = 0x0;
>>  
>> -	. = ALIGN(8);
>> +	.image_start : { *(.__image_start) }
>> +
>> +	. = ALIGN(4);
>> +	._text : { *(._text) }
>>  	.text      :
>>  	{
>>  		_stext = .;
>> -		_start = .;
>> -		KEEP(*(.text_entry*))
>> -		_text = .;
>> +		*(.text_entry*)
>> +		__bare_init_start = .;
>> +		*(.text_bare_init*)
>> +		__bare_init_end = .;
>> +		__exceptions_start = .;
>> +		KEEP(*(.text_exceptions*))
>> +		__exceptions_stop = .;
>>  		*(.text*)
>>  	}
>> +	BAREBOX_BARE_INIT_SIZE
>>  
>> -	. = ALIGN(8);
>> +	. = ALIGN(4);
>>  	.rodata : {
>>  		*(.rodata*)
>>  		RO_DATA_SECTION
>> @@ -38,7 +46,7 @@ SECTIONS
>>  	_etext = .;			/* End of text and rodata section */
>>  	_sdata = .;
>>  
>> -	. = ALIGN(8);
>> +	. = ALIGN(4);
>>  	.data : { *(.data*) }
>>  
>>  	.barebox_imd : { BAREBOX_IMD }
>> @@ -57,9 +65,13 @@ SECTIONS
>>  	}
>>  
>>  	_edata = .;
>> -	. = ALIGN(8);
>> -	__bss_start = .;
>> -	.bss : { *(.bss*) *(.sbss*) }
>> -	__bss_stop = .;
>> +
>> +	.image_end : { *(.__image_end) }
>> +
>> +	. = ALIGN(4);
>> +	.__bss_start :  { *(.__bss_start) }
>> +	.bss : { *(.bss*) }
>> +	.__bss_stop :  { *(.__bss_stop) }
>>  	_end = .;
>> +	_barebox_image_size = __bss_start;
>>  }
>> diff --git a/arch/riscv/lib/dtb.c b/arch/riscv/lib/dtb.c
>> new file mode 100644
>> index 000000000000..c7fa6b0c31ca
>> --- /dev/null
>> +++ b/arch/riscv/lib/dtb.c
>> @@ -0,0 +1,26 @@
>> +// SPDX-License-Identifier: GPL-2.0-only
>> +// SPDX-FileCopyrightText: 2013 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
>> +#include <common.h>
>> +#include <init.h>
>> +#include <of.h>
>> +#include <asm/barebox-riscv.h>
>> +
>> +static int of_riscv_init(void)
>> +{
>> +	void *fdt;
>> +
>> +	/* See if we are provided a dtb in boarddata */
>> +	fdt = barebox_riscv_boot_dtb();
>> +	if (!fdt) {
>> +		pr_err("No DTB found\n");
>> +		return -ENODATA;
>> +	}
>> +
>> +	pr_debug("using boarddata provided DTB\n");
>> +
>> +
>> +	barebox_register_fdt(fdt);
>> +
>> +	return 0;
>> +}
>> +core_initcall(of_riscv_init);
>> diff --git a/common/Kconfig b/common/Kconfig
>> index 36207274f07f..37204fb40a44 100644
>> --- a/common/Kconfig
>> +++ b/common/Kconfig
>> @@ -44,7 +44,7 @@ config BLOCK_WRITE
>>  
>>  config USE_COMPRESSED_DTB
>>  	bool
>> -	depends on ARM
>> +	depends on ARM || RISCV
>>  	select UNCOMPRESS
>>  	select LZO_DECOMPRESS
>>  
>> @@ -358,7 +358,7 @@ config KALLSYMS
>>  	  This is useful to print a nice backtrace when an exception occurs.
>>  
>>  config RELOCATABLE
>> -	depends on PPC || ARM
>> +	depends on PPC || ARM || RISCV
>>  	bool "generate relocatable barebox binary"
>>  	help
>>  	  A non relocatable barebox binary will run at it's compiled in
>> diff --git a/images/Makefile b/images/Makefile
>> index 84492a154d16..ee1347f6b6bd 100644
>> --- a/images/Makefile
>> +++ b/images/Makefile
>> @@ -42,6 +42,8 @@
>>  # both as entrypoint and as filename
>>  #
>>  
>> +include scripts/Makefile.lib
>> +
>>  quiet_cmd_objcopy_bin = OBJCOPYB $@
>>        cmd_objcopy_bin = \
>>  		$(OBJCOPY) -O binary $(OBJCOPYFLAGS) $(OBJCOPYFLAGS_$(@F)) $< $@ && \
>> @@ -64,6 +66,7 @@ PBL_CPPFLAGS	+= -fdata-sections -ffunction-sections
>>  
>>  $(obj)/%.pbl: $(pbl-lds) $(BAREBOX_PBL_OBJS) $(obj)/piggy.o $(obj)/sha_sum.o FORCE
>>  	$(call if_changed,elf__,$(*F))
>> +	$(call cmd,prelink__)
>>  
>>  $(obj)/%.pblb: $(obj)/%.pbl FORCE
>>  	$(call if_changed,objcopy_bin,$(*F))
>> @@ -164,6 +167,7 @@ include $(srctree)/images/Makefile.at91
>>  include $(srctree)/images/Makefile.zynq
>>  include $(srctree)/images/Makefile.zynqmp
>>  include $(srctree)/images/Makefile.layerscape
>> +include $(srctree)/images/Makefile.riscv
>>  
>>  
>>  pblb-$(CONFIG_BOARD_GENERIC_DT) += start_dt_2nd
>> diff --git a/images/Makefile.riscv b/images/Makefile.riscv
>> new file mode 100644
>> index 000000000000..463c6ce4400d
>> --- /dev/null
>> +++ b/images/Makefile.riscv
>> @@ -0,0 +1,12 @@
>> +# SPDX-License-Identifier: GPL-2.0-or-later
>> +
>> +quiet_cmd_erizo_nmon_image = MKIMAGE $@
>> +      cmd_erizo_nmon_image = $(srctree)/scripts/erizo-nmon-image $< $@ || \
>> +	echo "WARNING: Couldn't create erizo nmon image due to previous errors."
>> +
>> +$(obj)/%.nmon: $(obj)/%.img FORCE
>> +	$(call if_changed,erizo_nmon_image)
>> +
>> +pblb-$(CONFIG_BOARD_ERIZO_GENERIC) += start_erizo_generic
>> +FILE_barebox-erizo-generic.img = start_erizo_generic.pblb
>> +image-$(CONFIG_BOARD_ERIZO_GENERIC) += barebox-erizo-generic.img barebox-erizo-generic.nmon
>> diff --git a/pbl/Kconfig b/pbl/Kconfig
>> index 2eea5aef7a30..451a278c4088 100644
>> --- a/pbl/Kconfig
>> +++ b/pbl/Kconfig
>> @@ -27,7 +27,7 @@ config PBL_SINGLE_IMAGE
>>  if PBL_IMAGE
>>  
>>  config PBL_RELOCATABLE
>> -	depends on ARM || MIPS
>> +	depends on ARM || MIPS || RISCV
>>  	bool "relocatable pbl image"
>>  	help
>>  	  Generate a pbl binary which can relocate itself during startup to run
>> -- 
>> 2.29.2
>>
> 
> 

-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox


  reply	other threads:[~2021-03-16 18:40 UTC|newest]

Thread overview: 29+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-03-16  8:04 [PATCH v2 00/20] RISC-V: rework for PBL, VIRT and 64-Bit support Ahmad Fatoum
2021-03-16  8:04 ` [PATCH v2 01/20] partitions: don't allocate dma capable memory Ahmad Fatoum
2021-03-16  8:04 ` [PATCH v2 02/20] images: make BOARD_ARM_GENERIC_DT available for other arches Ahmad Fatoum
2021-03-16  8:04 ` [PATCH v2 03/20] ARM: make ARM_USE_COMPRESSED_DTB " Ahmad Fatoum
2021-03-16  8:04 ` [PATCH v2 04/20] ARM: aarch64: ommit unused label in assembly Ahmad Fatoum
2021-03-16  8:04 ` [PATCH v2 05/20] serial: virtio-console: depend on, but don't select VIRTIO Ahmad Fatoum
2021-03-16  8:04 ` [PATCH v2 06/20] filetype: detect RISC-V Linux kernel image Ahmad Fatoum
2021-03-16  8:04 ` [PATCH v2 07/20] asm: unaligned: don't do unaligned accesses Ahmad Fatoum
2021-03-16  8:04 ` [PATCH v2 08/20] RISC-V: debug_ll: ns16550: align C access size with assembly's Ahmad Fatoum
2021-03-16  8:04 ` [PATCH v2 09/20] RISC-V: drop duplicate or unneeded cflags Ahmad Fatoum
2021-03-16  8:04 ` [PATCH v2 10/20] RISC-V: add cacheless HAS_DMA support Ahmad Fatoum
2021-03-16  8:04 ` [PATCH v2 11/20] RISC-V: erizo: move to arch/riscv/boards/erizo Ahmad Fatoum
2021-03-16  8:04 ` [PATCH v2 12/20] RISC-V: import Linux' optimized string functions Ahmad Fatoum
2021-03-16  8:04 ` [PATCH v2 13/20] RISC-V: implement PBL and relocation support Ahmad Fatoum
2021-03-16  8:04 ` [PATCH v2 14/20] RISC-V: erizo: migrate to PBL Ahmad Fatoum
2021-03-16 14:12   ` Antony Pavlov
2021-03-16 18:38     ` Ahmad Fatoum [this message]
2021-03-19 15:37       ` Antony Pavlov
2021-03-19 18:28         ` Ahmad Fatoum
2021-03-20  5:55           ` Antony Pavlov
2021-03-21 15:14             ` Ahmad Fatoum
2021-03-20  7:49   ` Antony Pavlov
2021-03-21 15:16     ` Ahmad Fatoum
2021-03-16  8:05 ` [PATCH v2 15/20] RISC-V: support symbol names in barebox image Ahmad Fatoum
2021-03-16  8:05 ` [PATCH v2 16/20] RISC-V: add 64-bit support Ahmad Fatoum
2021-03-16  8:05 ` [PATCH v2 17/20] RISC-V: add generic DT image Ahmad Fatoum
2021-03-16  8:05 ` [PATCH v2 18/20] clocksource: add driver for RISC-V and CLINT timers Ahmad Fatoum
2021-03-16  8:05 ` [PATCH v2 19/20] power: reset: add drivers for generic syscon reset and poweroff Ahmad Fatoum
2021-03-16  8:05 ` [PATCH v2 20/20] RISC-V: add Qemu virt support Ahmad Fatoum

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=33c77bd7-e4c3-e258-b47b-84bdce1c00ee@pengutronix.de \
    --to=a.fatoum@pengutronix.de \
    --cc=antonynpavlov@gmail.com \
    --cc=barebox@lists.infradead.org \
    --cc=rcz@pengutronix.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox