Re: MFGTools from NXP

[Ahmad Fatoum <a.fatoum@pengutronix.de>]

On 10/16/19 11:21 AM, Mihaita Ivascu wrote:
> Hello,
> 
>    Thanks for your answer. Yes i am able to connect via PUTTY to the target.
>    Then I should use some adb commands in order to push the new
> barebox/firmware ? do you know where I could find some examples?

fastboot device -l works normally on Linux. You need to check what you need
to do on Windows to do the same. You should only need the Fastboot utility
for this.

> 
>    Also I have a question: purpose of this activity is for me to be
> able to flash some imx6ul boards that have no firmware: no barebox.
>    So I know hardware config for the port is otg mode but as I have no
> barebox running them before I am wondering if I will be able to
> connect via PUTTY if I do not set the ACM gadget from barebox?

Check the Embest MarS board's environment in barebox master. It sets up
a fastboot gadget automatically on boot from imx-usb-loader.
You can adjust it to your liking.

Cheers
Ahmad

> 
> Thanks,
>       Mihaita
> 
> On Wed, Oct 16, 2019 at 10:51 AM Ahmad Fatoum <a.fatoum@pengutronix.de> wrote:
>>
>> On 10/16/19 10:40 AM, Mihaita Ivascu wrote:
>>> Hello again,
>>>
>>>    I have the target in otg peripheral mode, ADB and fastboot drivers
>>> installed but fastboot does not list any device. The board is detected
>>> in device manager
>>
>> Try enabling the ACM gadget in barebox and connect with PuTTY and see if
>> at least that works. It worked for me on Windows with another i.MX board
>> a month ago.
>>
>> As for fastboot, I don't know how to configure it on Windows, but surely
>> Android Modding boards will have you covered there.
>>
>>>    Please see attachment. Any ideas how should I proceed? Thanks for
>>> the support.
>>
>> You can enable the ACM gadget in barebox and see if that works, I tested
>> it on Windows with an i.MX board a month ago
>>
>> Cheers
>> Ahmad
>>
>>>
>>> Thanks,
>>>       Mihaita
>>>
>>> On Wed, Oct 16, 2019 at 9:32 AM Mihaita Ivascu
>>> <mihaita_ivascu@trimble.com> wrote:
>>>>
>>>> Thanks. I have installed ADB and fastboot drivers for Win from
>>>> https://www.getdroidtips.com/how-to-install-adb-and-fastboot-on-windows/
>>>> I have installed according to the attachment.
>>>> But is not recognized in Windows. I did reboot the system after
>>>> installation but did not add any new env variable.
>>>>
>>>> H:\>fastboot devices -l
>>>> 'fastboot' is not recognized as an internal or external command,
>>>> operable program or batch file.
>>>>
>>>> Thanks,
>>>>       Mihaita
>>>>
>>>>
>>>> On Tue, Oct 15, 2019 at 4:44 PM Ahmad Fatoum <a.fatoum@pengutronix.de> wrote:
>>>>>
>>>>> On 10/15/19 4:41 PM, Mihaita Ivascu wrote:
>>>>>> barebox@Phytec phyCORE-i.MX6 Ultra Lite SOM:/ fastboot devices -l
>>>>> That's what you run on your host system, not on the target.
>>>>> --
>>>>> Pengutronix e.K.                           |                             |
>>>>> Industrial Linux Solutions                 | http://www.pengutronix.de/  |
>>>>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
>>>>> Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
>>
>>
>> --
>> Pengutronix e.K.                           |                             |
>> Industrial Linux Solutions                 | http://www.pengutronix.de/  |
>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
>> Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
> 


-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox