Re: MFGTools from NXP

[Ahmad Fatoum <a.fatoum@pengutronix.de>]

On 10/16/19 1:28 PM, Mihaita Ivascu wrote:
> On Wed, Oct 16, 2019 at 11:53 AM Ahmad Fatoum <a.fatoum@pengutronix.de>
> wrote:
>>
>>
>> On 10/16/19 11:48 AM, Mihaita Ivascu wrote:
>>> On Wed, Oct 16, 2019 at 11:26 AM Ahmad Fatoum <a.fatoum@pengutronix.de>
> wrote:
>>>>
>>>> On 10/16/19 11:21 AM, Mihaita Ivascu wrote:
>>>>> Hello,
>>>>>
>>>>>    Thanks for your answer. Yes i am able to connect via PUTTY to the
> target.
>>>>>    Then I should use some adb commands in order to push the new
>>>>> barebox/firmware ? do you know where I could find some examples?
>>>>
>>>> fastboot device -l works normally on Linux. You need to check what you
> need
>>>> to do on Windows to do the same. You should only need the Fastboot
> utility
>>>> for this.
>>>>
>>> [mi] Yes I have both fastboot and adb installed on both Windows and
>>> Linux machines. In both cases it does not list any device.
>>>        The board is detected as fastboot android is windows device
>>> manager. But the fastboot and adb does not list it. same for Linux.
>>> Please see attachment
>>
>> Let's focus on Linux. You don't see a device there?
>> What does barebox say? Does it say 'multi_bind: creating Fastboot
> function'?
>> What does you Linux host's dmesg say?
>>
> 
> barebox@Phytec phyCORE-i.MX6 Ultra Lite SOM:/ usbgadget -aA
> udc0: registering UDC driver [g_multi]
> multi_bind: creating Fastboot function
> multi_bind: creating ACM function
> g_multi usbgadget: Multifunction Composite Gadget
> g_multi usbgadget: userspace failed to provide iSerialNumber
> g_multi usbgadget: g_multi ready
> barebox@Phytec phyCORE-i.MX6 Ultra Lite SOM:/ g_multi usbgadget: high-speed
> config #1: Multifunction Composite Gadget
> 
> dmesg:
> 
> [   25.602275] usb 1-1.3: USB disconnect, device number 3
> [   28.359930] usb 1-1.3: new high-speed USB device number 5 using ehci-pci
> [   28.452971] usb 1-1.3: New USB device found, idVendor=1d6b,
> idProduct=0104
> [   28.452976] usb 1-1.3: New USB device strings: Mfr=0, Product=2,
> SerialNumber=0
> [   28.452980] usb 1-1.3: Product: Phytec phyCORE-i.MX6 Ultra Lite SOM
> [   28.457925] cdc_acm 1-1.3:1.1: ttyACM0: USB ACM device
> 
> 
> So I see the device on Linux. But fastboot does not list any device on
> Linux.

sudo doesn't change this?

> 
>>  >
>>>>>
>>>>>    Also I have a question: purpose of this activity is for me to be
>>>>> able to flash some imx6ul boards that have no firmware: no barebox.
>>>>>    So I know hardware config for the port is otg mode but as I have no
>>>>> barebox running them before I am wondering if I will be able to
>>>>> connect via PUTTY if I do not set the ACM gadget from barebox?
>>>>
>>>> Check the Embest MarS board's environment in barebox master. It sets up
>>>> a fastboot gadget automatically on boot from imx-usb-loader.
>>>> You can adjust it to your liking.
>>>
>>>   [mi] I was not able to find any docs about this board. I will keep
>>> searching/asking in the nxp community. If you have already ahve any
>>> files related to it would be helpful. Thanks
>>
>> It's in the barebox next branch (not master, sorry), see here:
>>
> https://github.com/saschahauer/barebox/blob/next/arch/arm/boards/embest-marsboard/defaultenv-mars/init/fastboot
>>
>> You can copy and adjust the environment setup for your board.
>>
>>>>
>>>> Cheers
>>>> Ahmad
>>>>
>>>>>
>>>>> Thanks,
>>>>>       Mihaita
>>>>>
>>>>> On Wed, Oct 16, 2019 at 10:51 AM Ahmad Fatoum <a.fatoum@pengutronix.de>
> wrote:
>>>>>>
>>>>>> On 10/16/19 10:40 AM, Mihaita Ivascu wrote:
>>>>>>> Hello again,
>>>>>>>
>>>>>>>    I have the target in otg peripheral mode, ADB and fastboot
> drivers
>>>>>>> installed but fastboot does not list any device. The board is
> detected
>>>>>>> in device manager
>>>>>>
>>>>>> Try enabling the ACM gadget in barebox and connect with PuTTY and
> see if
>>>>>> at least that works. It worked for me on Windows with another i.MX
> board
>>>>>> a month ago.
>>>>>>
>>>>>> As for fastboot, I don't know how to configure it on Windows, but
> surely
>>>>>> Android Modding boards will have you covered there.
>>>>>>
>>>>>>>    Please see attachment. Any ideas how should I proceed? Thanks for
>>>>>>> the support.
>>>>>>
>>>>>> You can enable the ACM gadget in barebox and see if that works, I
> tested
>>>>>> it on Windows with an i.MX board a month ago
>>>>>>
>>>>>> Cheers
>>>>>> Ahmad
>>>>>>
>>>>>>>
>>>>>>> Thanks,
>>>>>>>       Mihaita
>>>>>>>
>>>>>>> On Wed, Oct 16, 2019 at 9:32 AM Mihaita Ivascu
>>>>>>> <mihaita_ivascu@trimble.com> wrote:
>>>>>>>>
>>>>>>>> Thanks. I have installed ADB and fastboot drivers for Win from
>>>>>>>>
> https://www.getdroidtips.com/how-to-install-adb-and-fastboot-on-windows/
>>>>>>>> I have installed according to the attachment.
>>>>>>>> But is not recognized in Windows. I did reboot the system after
>>>>>>>> installation but did not add any new env variable.
>>>>>>>>
>>>>>>>> H:\>fastboot devices -l
>>>>>>>> 'fastboot' is not recognized as an internal or external command,
>>>>>>>> operable program or batch file.
>>>>>>>>
>>>>>>>> Thanks,
>>>>>>>>       Mihaita
>>>>>>>>
>>>>>>>>
>>>>>>>> On Tue, Oct 15, 2019 at 4:44 PM Ahmad Fatoum <
> a.fatoum@pengutronix.de> wrote:
>>>>>>>>>
>>>>>>>>> On 10/15/19 4:41 PM, Mihaita Ivascu wrote:
>>>>>>>>>> barebox@Phytec phyCORE-i.MX6 Ultra Lite SOM:/ fastboot devices -l
>>>>>>>>> That's what you run on your host system, not on the target.
>>>>>>>>> --
>>>>>>>>> Pengutronix e.K.                           |
>         |
>>>>>>>>> Industrial Linux Solutions                 |
> http://www.pengutronix.de/  |
>>>>>>>>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone:
> +49-5121-206917-0    |
>>>>>>>>> Amtsgericht Hildesheim, HRA 2686           | Fax:
> +49-5121-206917-5555 |
>>>>>>
>>>>>>
>>>>>> --
>>>>>> Pengutronix e.K.                           |
>     |
>>>>>> Industrial Linux Solutions                 |
> http://www.pengutronix.de/  |
>>>>>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone:
> +49-5121-206917-0    |
>>>>>> Amtsgericht Hildesheim, HRA 2686           | Fax:
> +49-5121-206917-5555 |
>>>>>
>>>>
>>>>
>>>> --
>>>> Pengutronix e.K.                           |
>   |
>>>> Industrial Linux Solutions                 | http://www.pengutronix.de/
>  |
>>>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0
>    |
>>>> Amtsgericht Hildesheim, HRA 2686           | Fax:
> +49-5121-206917-5555 |
>>
>> --
>> Pengutronix e.K.                           |                             |
>> Industrial Linux Solutions                 | http://www.pengutronix.de/  |
>> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
>> Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
> 

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox