mail archive of the barebox mailing list
 help / color / mirror / Atom feed
From: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
To: Gregory Hermant <gregory.hermant@calao-systems.com>
Cc: barebox@lists.infradead.org
Subject: Re: [PATCH] add support for the haba-knx-lite controller
Date: Sun, 18 Jan 2015 05:51:42 +0800	[thread overview]
Message-ID: <6FA9453A-61C8-4761-9637-9597D1287377@jcrosoft.com> (raw)
In-Reply-To: <1421320118-31779-1-git-send-email-gregory.hermant@calao-systems.com>


> On Jan 15, 2015, at 7:08 PM, Gregory Hermant <gregory.hermant@calao-systems.com> wrote:
> 
> 
> Signed-off-by: Gregory Hermant <gregory.hermant@calao-systems.com>
> ---
> arch/arm/boards/Makefile                    |    1 +
> arch/arm/boards/haba-knx/Makefile           |    1 +
> arch/arm/boards/haba-knx/env/bin/init_board |   49 ++++
> arch/arm/boards/haba-knx/env/config         |   40 +++
> arch/arm/boards/haba-knx/init.c             |  348 +++++++++++++++++++++++++++
> arch/arm/configs/haba_knx_lite_defconfig    |   89 +++++++
> arch/arm/mach-at91/Kconfig                  |    5 +
> 7 files changed, 533 insertions(+)
> create mode 100644 arch/arm/boards/haba-knx/Makefile
> create mode 100644 arch/arm/boards/haba-knx/env/bin/init_board
> create mode 100644 arch/arm/boards/haba-knx/env/config
> create mode 100644 arch/arm/boards/haba-knx/init.c
> create mode 100644 arch/arm/configs/haba_knx_lite_defconfig
> 
> diff --git a/arch/arm/boards/Makefile b/arch/arm/boards/Makefile
> index 9961ca8..bf04f38 100644
> --- a/arch/arm/boards/Makefile
> +++ b/arch/arm/boards/Makefile
> @@ -50,6 +50,7 @@ obj-$(CONFIG_MACH_GUF_CUPID)			+= guf-cupid/
> obj-$(CONFIG_MACH_GUF_SANTARO)			+= guf-santaro/
> obj-$(CONFIG_MACH_GUF_VINCELL)			+= guf-vincell/
> obj-$(CONFIG_MACH_GW_VENTANA)			+= gateworks-ventana/
> +obj-$(CONFIG_MACH_HABA_KNX_LITE)		+= haba-knx/
> obj-$(CONFIG_MACH_HIGHBANK)			+= highbank/
> obj-$(CONFIG_MACH_IMX21ADS)			+= freescale-mx21-ads/
> obj-$(CONFIG_MACH_IMX233_OLINUXINO)		+= imx233-olinuxino/
> diff --git a/arch/arm/boards/haba-knx/Makefile b/arch/arm/boards/haba-knx/Makefile
> new file mode 100644
> index 0000000..eb072c0
> --- /dev/null
> +++ b/arch/arm/boards/haba-knx/Makefile
> @@ -0,0 +1 @@
> +obj-y += init.o
> diff --git a/arch/arm/boards/haba-knx/env/bin/init_board b/arch/arm/boards/haba-knx/env/bin/init_board
> new file mode 100644
> index 0000000..0a6baf7
> --- /dev/null
> +++ b/arch/arm/boards/haba-knx/env/bin/init_board
> @@ -0,0 +1,49 @@
> +#!/bin/sh
> +
> +button_name="dfu_bp"
> +button_wait=5
> +
> +product_id=0x1234
> +vendor_id=0x4321
> +
> +dfu_config="/dev/nand0.barebox.bb(barebox)sr,/dev/nand0.kernel.bb(kernel)r,/dev/nand0.rootfs.bb(rootfs)r"
> +
> +if [ $at91_udc0.vbus != 1 ]
> +then
> +	echo "No USB Device cable plugged, normal boot"
> +	exit
> +fi
> +
> +gpio_get_value ${dfu_button}
> +if [ $? != 0 ]
> +then
> +	autoboot_timeout=16
> +	echo "enable tty over USB Device, increase the boot delay to ${autoboot_timeout}s"
> +	usbserial
> +	exit
> +fi
> +
> +echo "${button_name} pressed detected wait ${button_wait}s"
> +timeout -s -a ${button_wait}
> +
> +if [ $at91_udc0.vbus != 1 ]
> +then
> +	echo "No USB Device cable plugged, normal boot"
> +	exit
> +fi
> +
> +gpio_get_value ${dfu_button}
> +if [ $? != 0 ]
> +then
> +	echo "${button_name} released, normal boot"
> +	autoboot_timeout=16
> +	echo "enable tty over USB Device, increase the boot delay to ${autoboot_timeout}s"
> +	usbserial
> +	exit
> +fi
> +
> +echo ""
> +echo "Start DFU Mode"
> +echo ""
> +
> +dfu ${dfu_config} -P ${product_id} -V ${vendor_id}
> diff --git a/arch/arm/boards/haba-knx/env/config b/arch/arm/boards/haba-knx/env/config
> new file mode 100644
> index 0000000..d1dca10
> --- /dev/null
> +++ b/arch/arm/boards/haba-knx/env/config
> @@ -0,0 +1,40 @@
> +#!/bin/sh
> +
> +# use 'dhcp' to do dhcp in barebox and in kernel
> +# use 'none' if you want to skip kernel ip autoconfiguration
> +ip=none
> +#ip=dhcp-barebox
> +[ x$armlinux_architecture = x4310 ] && dhcp_vendor_id=barebox-haba-knx-lite
> +
> +# or set your networking parameters here
> +#eth0.ipaddr=a.b.c.d
> +#eth0.netmask=a.b.c.d
> +#eth0.gateway=a.b.c.d
> +#eth0.serverip=a.b.c.d
> +
> +# can be either 'nfs', 'tftp', 'nor' or 'nand'
> +kernel_loc=nand
> +# can be either 'net', 'nor', 'nand' or 'initrd'
> +rootfs_loc=nand
> +# can be either 'nfs', 'tftp', 'nor', 'nand' or empty
> +oftree_loc=nand
> +
> +# can be either 'jffs2' or 'ubifs'
> +rootfs_type=ubifs
> +rootfsimage=root.$rootfs_type
> +
> +kernelimage=zImage
> +#kernelimage=uImage
> +#kernelimage=Image
> +#kernelimage=Image.lzo
> +
> +nand_device=atmel_nand
> +nand_parts="128k(at91bootstrap),256k(barebox)ro,128k(bareboxenv),128k(bareboxenv2),128k(oftree),4M(kernel),120M(rootfs),-(data)"
> +rootfs_mtdblock_nand=6
> +
> +autoboot_timeout=3
> +
> +bootargs="console=ttyS0,115200"
> +
> +# set a fancy prompt (if support is compiled in)
> +PS1="\e[1;32mbarebox@\e[1;31m\h:\w\e[0m\n# "
> diff --git a/arch/arm/boards/haba-knx/init.c b/arch/arm/boards/haba-knx/init.c
> new file mode 100644
> index 0000000..f9d8f0f
> --- /dev/null
> +++ b/arch/arm/boards/haba-knx/init.c
> @@ -0,0 +1,348 @@
> +/*
> + * Copyright (C) 2011-2012 Jean-Christophe PLAGNIOL-VILLARD
> + * Copyright (C) 2014 Gregory Hermant <gregory.hermant@calao-systems.com>
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + *
> + */
> +
> +#include <common.h>
> +#include <net.h>
> +#include <init.h>
> +#include <environment.h>
> +#include <asm/armlinux.h>
> +#include <generated/mach-types.h>
> +#include <partition.h>
> +#include <fs.h>
> +#include <fcntl.h>
> +#include <io.h>
> +#include <mach/hardware.h>
> +#include <nand.h>
> +#include <linux/sizes.h>
> +#include <linux/mtd/nand.h>
> +#include <linux/clk.h>
> +#include <mach/board.h>
> +#include <mach/at91sam9_smc.h>
> +#include <gpio.h>
> +#include <led.h>
> +#include <mach/io.h>
> +#include <mach/iomux.h>
> +#include <mach/at91_pmc.h>
> +#include <mach/at91_rstc.h>
> +#include <spi/spi.h>
> +#include <i2c/i2c.h>
> +#include <libfile.h>
> +
> +#if defined(CONFIG_NAND_ATMEL)
> +static struct atmel_nand_data nand_pdata = {
> +	.ale		= 21,
> +	.cle		= 22,
> +	.det_pin	= -EINVAL,
> +	.rdy_pin	= AT91_PIN_PC13,
> +	.enable_pin	= AT91_PIN_PC14,
> +	.ecc_mode	= NAND_ECC_SOFT,
> +	.on_flash_bbt	= 1,
> +};
> +
> +static struct sam9_smc_config haba_knx_nand_smc_config = {
> +	.ncs_read_setup		= 0,
> +	.nrd_setup		= 2,
> +	.ncs_write_setup	= 0,
> +	.nwe_setup		= 2,
> +
> +	.ncs_read_pulse		= 4,
> +	.nrd_pulse		= 4,
> +	.ncs_write_pulse	= 4,
> +	.nwe_pulse		= 4,
> +
> +	.read_cycle		= 7,
> +	.write_cycle		= 7,
> +
> +	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
> +				  AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
> +	.tdf_cycles		= 3,
> +};
> +
> +static void haba_knx_add_device_nand(void)
> +{
> +	/* configure chip-select 3 (NAND) */
> +	sam9_smc_configure(0, 3, &haba_knx_nand_smc_config);
> +	at91_add_device_nand(&nand_pdata);
> +}
> +#else
> +static void haba_knx_add_device_nand(void) {}
> +#endif
> +
> +#if defined(CONFIG_DRIVER_NET_MACB)
> +static struct macb_platform_data macb_pdata = {
> +	.phy_interface	= PHY_INTERFACE_MODE_RMII,
> +	.phy_addr	= -1,
> +};
> +
> +static void haba_knx_phy_reset(void)
> +{
> +	unsigned long rstc;
> +	struct clk *clk = clk_get(NULL, "macb_clk");
> +
> +	clk_enable(clk);
> +
> +	at91_set_gpio_input(AT91_PIN_PA14, 0);
> +	at91_set_gpio_input(AT91_PIN_PA15, 0);
> +	at91_set_gpio_input(AT91_PIN_PA17, 0);
> +	at91_set_gpio_input(AT91_PIN_PA18, 0);
> +
> +	rstc = at91_sys_read(AT91_RSTC_MR) & AT91_RSTC_ERSTL;
> +
> +	/* Need to reset PHY -> 500ms reset */
> +	at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
> +				     (AT91_RSTC_ERSTL & (0x0d << 8)) |
> +				     AT91_RSTC_URSTEN);
> +
> +	at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_EXTRST);
> +
> +	/* Wait for end hardware reset */
> +	while (!(at91_sys_read(AT91_RSTC_SR) & AT91_RSTC_NRSTL))
> +		;
> +
> +	/* Restore NRST value */
> +	at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
> +				     (rstc) |
> +				     AT91_RSTC_URSTEN);
> +}
> +
> +#define MACB_SA1B	0x0098
> +#define MACB_SA1T	0x009c
> +
> +static int haba_ip_get_macb_ethaddr(u8 *addr)
> +{[
> +	u32 top, bottom;
> +	void __iomem *base = IOMEM(AT91SAM9260_BASE_EMAC);
> +
> +	bottom = readl(base + MACB_SA1B);
> +	top = readl(base + MACB_SA1T);
> +	addr[0] = bottom & 0xff;
> +	addr[1] = (bottom >> 8) & 0xff;
> +	addr[2] = (bottom >> 16) & 0xff;
> +	addr[3] = (bottom >> 24) & 0xff;
> +	addr[4] = top & 0xff;
> +	addr[5] = (top >> 8) & 0xff;
> +
> +	/* valid and not private */
> +	if (is_valid_ether_addr(addr) && !(addr[0] & 0x02))
> +		return 0;
> +
> +	return -EINVAL;
> +}
> +
> +#define EEPROM_OFFSET 250
> +#define EEPROM_SIZE 256
> +
> +static int haba_set_ethaddr(void)
> +{
> +	char addr[6];
> +	char eep_data[256];
> +	int i, fd, ret;
> +
> +	fd = open("/dev/eeprom0", O_RDONLY);
> +	if (fd < 0) {
> +		ret = fd;
> +		goto err;
> +	}
> +
> +	ret = read_full(fd, eep_data, EEPROM_SIZE);
> +	if (ret < 0)
> +		goto err_open;
> +
> +	for (i = 0; i < 6; i++)
> +		addr[i] = eep_data[EEPROM_OFFSET+i];
> +
> +	eth_register_ethaddr(0, addr);
> +
> +	ret = 0;
> +
> +err_open:
> +	close(fd);
> +err:
> +	if (ret)
> +		pr_err("can't read eeprom /dev/eeprom0 (%s)\n", strerror(ret));
> +
> +	return ret;
> +}
Generic should no be in board file
> +
> +static void haba_knx_add_device_eth(void)
> +{
> +	u8 enetaddr[6];
> +
> +	if (!haba_ip_get_macb_ethaddr(enetaddr))
	Do you really need to check I do remember when I work on this patch that I
	put it in case you re-run barebox for ram
	and do not want to overwrite the mac

	But as it’s macb related the code to retrieve the mac should be move to a inline
	in the macb header (as this code is used by the driver too)
	

> +		eth_register_ethaddr(0, enetaddr);
		no need this register it will be handle by the macb driver
> +	else
> +		haba_set_ethaddr();
> +
> +	haba_knx_phy_reset();
> +	at91_add_device_eth(0, &macb_pdata);
> +}
> +#else
> +static void haba_knx_add_device_eth(void) {}
> +#endif
> +
> +/*
> + * USB Device port
> + */
> +static struct at91_udc_data __initdata ek_udc_data = {
> +	.vbus_pin	= AT91_PIN_PB2,
> +	.pullup_pin	= 0,		/* pull-up driven by UDC */
> +};
> +
> +static struct i2c_board_info i2c_devices[] = {
> +	{
> +		I2C_BOARD_INFO("24c02", 0x50)
> +	}
> +};
> +
> +static const struct spi_board_info ek_spi_devices[] = {
> +	{
> +		.name		= "m25p16",
> +		.max_speed_hz	= 30 * 1000 * 1000,
> +		.bus_num	= 0,
> +		.chip_select	= 0,
> +	},
> +	{
> +		.name		= "spi_mci",
> +		.max_speed_hz	= 25 * 1000 * 1000,
> +		.bus_num	= 0,
> +		.chip_select	= 1,
> +	}
> +};
> +
> +static unsigned spi0_standard_cs[] = { AT91_PIN_PA3, AT91_PIN_PA27 };
> +static struct at91_spi_platform_data spi_pdata = {
> +	.chipselect = spi0_standard_cs,
> +	.num_chipselect = ARRAY_SIZE(spi0_standard_cs),
> +};
I’ll drop this soon, and instead pass the cs gpio via board_info as done on linux
> +
> +static void haba_knx_add_device_spi(void)
> +{
> +	if (machine_is_haba_knx_lite()) {
> +		spi_register_board_info(ek_spi_devices,
> +					ARRAY_SIZE(ek_spi_devices));
> +		at91_add_device_spi(0, &spi_pdata);
> +	}
> +}
> +
> +static struct at91_usbh_data haba_knx_usbh_data = {
> +	.ports		= 2,
> +	.vbus_pin	= { -EINVAL, -EINVAL },
> +};
> +
> +static void haba_knx_add_device_usb(void)
> +{
> +	at91_add_device_usbh_ohci(&haba_knx_usbh_data);
> +}
> +
> +struct gpio_led led = {
> +	.gpio = AT91_PIN_PA28,
> +	.led = {
> +		.name = "user_led",
> +	},
> +};
> +
> +static void __init ek_add_led(void)
> +{
> +	if (!machine_is_haba_knx_lite())
> +		return;

you only add the lite version in this patch
> +	at91_set_gpio_output(led.gpio, led.active_low);
> +	led_gpio_register(&led);
> +}
> +
> +static int haba_knx_mem_init(void)
> +{
> +	at91_add_device_sdram(0);
> +	return 0;
> +}
> +mem_initcall(haba_knx_mem_init);
> +
> +static void __init ek_add_device_button(void)
> +{
> +	at91_set_GPIO_periph(AT91_PIN_PC3, 1);	/* user btn, pull up enabled */
> +	at91_set_deglitch(AT91_PIN_PC3, 1);
> +	export_env_ull("dfu_button", AT91_PIN_PC3);
> +}
> +
> +static const struct devfs_partition haba_knx_nand0_partitions[] = {
> +	{
> +		.offset = 0x00000,
> +		.size = SZ_128K,
> +		.flags = DEVFS_PARTITION_FIXED,
> +		.name = "at91bootstrap_raw",
> +		.bbname = "at91bootstrap",
> +	}, {
> +		.offset = DEVFS_PARTITION_APPEND,
> +		.size = SZ_256K,
> +		.flags = DEVFS_PARTITION_FIXED,
> +		.name = "self_raw",
> +		.bbname = "self0",
> +	}, {
> +		.offset = DEVFS_PARTITION_APPEND,
> +		.size = SZ_128K,
> +		.flags = DEVFS_PARTITION_FIXED,
> +		.name = "env_raw",
> +		.bbname = "env0",
> +	}, {
> +		.offset = DEVFS_PARTITION_APPEND,
> +		.size = SZ_128K,
> +		.flags = DEVFS_PARTITION_FIXED,
> +		.name = "env_raw1",
> +		.bbname = "env1",
> +	}, {
> +		/* sentinel */
> +	}
> +};
> +
> +static int haba_knx_devices_init(void)
> +{
> +	at91_add_device_i2c(0, i2c_devices, ARRAY_SIZE(i2c_devices));
> +	haba_knx_add_device_nand();
> +	haba_knx_add_device_eth();
> +	haba_knx_add_device_spi();
> +	haba_knx_add_device_usb();
> +	at91_add_device_udc(&ek_udc_data);
> +	ek_add_led();
> +	ek_add_device_button();
> +
> +	armlinux_set_bootparams((void *)(AT91_CHIPSELECT_1 + 0x100));
> +	armlinux_set_architecture(MACH_TYPE_HABA_KNX_LITE);
> +
> +	devfs_create_partitions("nand0", haba_knx_nand0_partitions);
> +
> +	return 0;
> +}
> +device_initcall(haba_knx_devices_init);
> +
> +static int haba_knx_console_init(void)
> +{
> +	barebox_set_model("CALAO HABA-KNX-LITE");
> +	barebox_set_hostname("haba-knx-lite");
> +
> +	at91_register_uart(0, 0);
> +	at91_set_A_periph(AT91_PIN_PB14, 1);    /* Enable pull-up on DRXD */
> +
> +	at91_set_gpio_input(AT91_PIN_PB0, 1);	/* Enable pull-up on usd CD */
> +	return 0;
> +}
> +console_initcall(haba_knx_console_init);
> +
> +static int haba_knx_main_clock(void)
> +{
> +	at91_set_main_clock(12000000);
> +	return 0;
> +}
> +pure_initcall(haba_knx_main_clock);
> diff --git a/arch/arm/configs/haba_knx_lite_defconfig b/arch/arm/configs/haba_knx_lite_defconfig
> new file mode 100644
> index 0000000..62d66bc
> --- /dev/null
> +++ b/arch/arm/configs/haba_knx_lite_defconfig
> @@ -0,0 +1,89 @@
> +CONFIG_ARCH_AT91SAM9G20=y
> +CONFIG_MACH_HABA_KNX_LITE=y
> +CONFIG_BAREBOX_MAX_IMAGE_SIZE=0x40000
> +CONFIG_AEABI=y
> +CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y
> +CONFIG_PBL_IMAGE=y
> +CONFIG_MMU=y
> +CONFIG_TEXT_BASE=0x27f00000
> +CONFIG_EXPERIMENTAL=y
> +CONFIG_MALLOC_TLSF=y
> +CONFIG_PROMPT="HABA-KNX-LITE:"
> +CONFIG_GLOB=y
> +CONFIG_PROMPT_HUSH_PS2="y"
> +CONFIG_HUSH_FANCY_PROMPT=y
> +CONFIG_CMDLINE_EDITING=y
> +CONFIG_AUTO_COMPLETE=y
> +CONFIG_MENU=y
> +CONFIG_CONSOLE_ACTIVATE_ALL=y
> +CONFIG_DEFAULT_ENVIRONMENT_GENERIC=y
> +CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/haba-knx/env”
please use defaultenv2 now
> +# CONFIG_CMD_ARM_CPUINFO is not set
> +CONFIG_LONGHELP=y
> +CONFIG_CMD_MEMINFO=y
> +CONFIG_CMD_BOOTM_SHOW_TYPE=y
> +CONFIG_CMD_BOOTM_VERBOSE=y
> +CONFIG_CMD_BOOTM_INITRD=y
> +CONFIG_CMD_BOOTM_OFTREE=y
> +CONFIG_CMD_BOOTM_OFTREE_UIMAGE=y
> +# CONFIG_CMD_BOOTU is not set
> +CONFIG_CMD_GO=y
> +CONFIG_CMD_LOADB=y
> +CONFIG_CMD_RESET=y
> +CONFIG_CMD_UIMAGE=y
> +CONFIG_CMD_PARTITION=y
> +CONFIG_CMD_EXPORT=y
> +CONFIG_CMD_PRINTENV=y
> +CONFIG_CMD_SAVEENV=y
> +CONFIG_CMD_MD5SUM=y
> +CONFIG_CMD_SHA1SUM=y
> +CONFIG_CMD_SLEEP=y
> +CONFIG_CMD_TFTP=y
> +CONFIG_CMD_ECHO_E=y
> +CONFIG_CMD_EDIT=y
> +CONFIG_CMD_MENU=y
> +CONFIG_CMD_MENU_MANAGEMENT=y
> +CONFIG_CMD_READLINE=y
> +CONFIG_CMD_TIMEOUT=y
> +CONFIG_CMD_FLASH=y
> +CONFIG_CMD_GPIO=y
> +CONFIG_CMD_I2C=y
> +CONFIG_CMD_LED=y
> +CONFIG_CMD_SPI=y
> +CONFIG_CMD_LED_TRIGGER=y
> +CONFIG_CMD_BAREBOX_UPDATE=y
> +CONFIG_CMD_OFTREE=y
> +CONFIG_NET=y
> +CONFIG_NET_NFS=y
> +CONFIG_NET_NETCONSOLE=y
> +CONFIG_DRIVER_NET_MACB=y
> +CONFIG_DRIVER_SPI_ATMEL=y
> +CONFIG_I2C=y
> +CONFIG_I2C_GPIO=y
> +CONFIG_MTD=y
> +# CONFIG_MTD_OOB_DEVICE is not set
> +CONFIG_MTD_M25P80=y
> +CONFIG_NAND=y
> +# CONFIG_NAND_ECC_HW is not set
> +# CONFIG_NAND_ECC_HW_SYNDROME is not set
> +# CONFIG_NAND_ECC_HW_NONE is not set
> +CONFIG_NAND_ATMEL=y
> +CONFIG_MTD_UBI=y
> +CONFIG_USB_GADGET=y
> +CONFIG_USB_GADGET_SERIAL=y
> +CONFIG_MCI=y
> +# CONFIG_MCI_INFO is not set
> +# CONFIG_MCI_WRITE is not set
> +CONFIG_MCI_SPI=y
> +CONFIG_MMC_SPI_CRC_ON=y
> +CONFIG_LED=y
> +CONFIG_LED_GPIO=y
> +CONFIG_LED_TRIGGERS=y
> +CONFIG_EEPROM_AT24=y
> +CONFIG_FS_TFTP=y
> +CONFIG_FS_FAT=y
> +CONFIG_FS_FAT_WRITE=y
> +CONFIG_FS_FAT_LFN=y
> +CONFIG_FS_UBIFS=y
> +CONFIG_ZLIB=y
> +CONFIG_LZO_DECOMPRESS=y
> diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
> index 9ee4f30..b85e6fa 100644
> --- a/arch/arm/mach-at91/Kconfig
> +++ b/arch/arm/mach-at91/Kconfig
> @@ -352,6 +352,11 @@ config MACH_QIL_A9G20
> 	  Select this if you are using a Calao Systems QIL-A9G20 Board.
> 	  <http://www.calao-systems.com>
> 
> +config MACH_HABA_KNX_LITE
> +	bool "CALAO HABA-KNX-LITE"
> +	help
> +	  Select this if you are using a Calao Systems HABA-KNX-LITE.
> +	  <http://www.calao-systems.com>
> endchoice
> 
> endif
> -- 
> 1.7.9.5
> 
> 
> _______________________________________________
> barebox mailing list
> barebox@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

      parent reply	other threads:[~2015-01-17 21:52 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2015-01-15 11:08 Gregory Hermant
2015-01-16  7:09 ` Sascha Hauer
2015-01-17 21:51 ` Jean-Christophe PLAGNIOL-VILLARD [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=6FA9453A-61C8-4761-9637-9597D1287377@jcrosoft.com \
    --to=plagnioj@jcrosoft.com \
    --cc=barebox@lists.infradead.org \
    --cc=gregory.hermant@calao-systems.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox