* [PATCH 1/7] ARM: socfpga: rename socfpga->cyclone5
2017-04-03 10:55 [PATCH 0/7] SoCFPGA: add support for Arria10 Steffen Trumtrar
@ 2017-04-03 10:55 ` Steffen Trumtrar
2017-04-03 10:55 ` [PATCH 2/7] clk: socfpga: move driver to subdirectory Steffen Trumtrar
` (6 subsequent siblings)
7 siblings, 0 replies; 12+ messages in thread
From: Steffen Trumtrar @ 2017-04-03 10:55 UTC (permalink / raw)
To: barebox; +Cc: Steffen Trumtrar
Prepare the SoCFPGA code base for different system types
(Arria10, Stratix10,...).
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
---
arch/arm/boards/altera-socdk/board.c | 2 +-
.../boards/altera-socdk/iocsr_config_cyclone5.c | 2 +-
arch/arm/boards/altera-socdk/lowlevel.c | 4 +-
arch/arm/boards/ebv-socrates/board.c | 2 +-
.../boards/ebv-socrates/iocsr_config_cyclone5.c | 2 +-
arch/arm/boards/ebv-socrates/lowlevel.c | 4 +-
arch/arm/boards/terasic-de0-nano-soc/board.c | 2 +-
.../terasic-de0-nano-soc/iocsr_config_cyclone5.c | 2 +-
arch/arm/boards/terasic-de0-nano-soc/lowlevel.c | 4 +-
arch/arm/boards/terasic-sockit/board.c | 1 -
.../boards/terasic-sockit/iocsr_config_cyclone5.c | 2 +-
arch/arm/boards/terasic-sockit/lowlevel.c | 4 +-
arch/arm/mach-socfpga/Makefile | 6 +-
.../{bootsource.c => cyclone5-bootsource.c} | 12 +-
.../{clock-manager.c => cyclone5-clock-manager.c} | 4 +-
...e-controller.c => cyclone5-freeze-controller.c} | 2 +-
arch/arm/mach-socfpga/cyclone5-generic.c | 210 +++++++++++++++++++++
arch/arm/mach-socfpga/{init.c => cyclone5-init.c} | 10 +-
.../{reset-manager.c => cyclone5-reset-manager.c} | 4 +-
.../{scan-manager.c => cyclone5-scan-manager.c} | 4 +-
...{system-manager.c => cyclone5-system-manager.c} | 4 +-
.../{clock-manager.h => cyclone5-clock-manager.h} | 6 +-
...e-controller.h => cyclone5-freeze-controller.h} | 6 +-
.../mach/{socfpga-regs.h => cyclone5-regs.h} | 0
.../{reset-manager.h => cyclone5-reset-manager.h} | 0
.../{scan-manager.h => cyclone5-scan-manager.h} | 2 +-
.../{sdram_config.h => cyclone5-sdram-config.h} | 6 +-
.../include/mach/{sdram.h => cyclone5-sdram.h} | 0
.../mach/{sequencer.c => cyclone5-sequencer.c} | 6 +-
.../mach/{sequencer.h => cyclone5-sequencer.h} | 0
...{system-manager.h => cyclone5-system-manager.h} | 0
arch/arm/mach-socfpga/include/mach/pll_config.h | 2 +-
arch/arm/mach-socfpga/include/mach/sdram_io.h | 2 +-
.../mach-socfpga/include/mach/sequencer_defines.h | 6 -
arch/arm/mach-socfpga/include/mach/system.h | 0
arch/arm/mach-socfpga/include/mach/tclrpt.h | 2 +-
arch/arm/mach-socfpga/nic301.c | 2 +-
arch/arm/mach-socfpga/xload.c | 4 +-
drivers/firmware/socfpga.c | 8 +-
scripts/socfpga_import_preloader | 2 +-
40 files changed, 271 insertions(+), 70 deletions(-)
rename arch/arm/mach-socfpga/{bootsource.c => cyclone5-bootsource.c} (79%)
rename arch/arm/mach-socfpga/{clock-manager.c => cyclone5-clock-manager.c} (99%)
rename arch/arm/mach-socfpga/{freeze-controller.c => cyclone5-freeze-controller.c} (99%)
create mode 100644 arch/arm/mach-socfpga/cyclone5-generic.c
rename arch/arm/mach-socfpga/{init.c => cyclone5-init.c} (89%)
rename arch/arm/mach-socfpga/{reset-manager.c => cyclone5-reset-manager.c} (96%)
rename arch/arm/mach-socfpga/{scan-manager.c => cyclone5-scan-manager.c} (98%)
rename arch/arm/mach-socfpga/{system-manager.c => cyclone5-system-manager.c} (93%)
rename arch/arm/mach-socfpga/include/mach/{clock-manager.h => cyclone5-clock-manager.h} (99%)
rename arch/arm/mach-socfpga/include/mach/{freeze-controller.h => cyclone5-freeze-controller.h} (96%)
rename arch/arm/mach-socfpga/include/mach/{socfpga-regs.h => cyclone5-regs.h} (100%)
rename arch/arm/mach-socfpga/include/mach/{reset-manager.h => cyclone5-reset-manager.h} (100%)
rename arch/arm/mach-socfpga/include/mach/{scan-manager.h => cyclone5-scan-manager.h} (99%)
rename arch/arm/mach-socfpga/include/mach/{sdram_config.h => cyclone5-sdram-config.h} (98%)
rename arch/arm/mach-socfpga/include/mach/{sdram.h => cyclone5-sdram.h} (100%)
rename arch/arm/mach-socfpga/include/mach/{sequencer.c => cyclone5-sequencer.c} (99%)
rename arch/arm/mach-socfpga/include/mach/{sequencer.h => cyclone5-sequencer.h} (100%)
rename arch/arm/mach-socfpga/include/mach/{system-manager.h => cyclone5-system-manager.h} (100%)
mode change 100755 => 100644 arch/arm/mach-socfpga/include/mach/sdram_io.h
delete mode 100644 arch/arm/mach-socfpga/include/mach/sequencer_defines.h
mode change 100755 => 100644 arch/arm/mach-socfpga/include/mach/system.h
mode change 100755 => 100644 arch/arm/mach-socfpga/include/mach/tclrpt.h
diff --git a/arch/arm/boards/altera-socdk/board.c b/arch/arm/boards/altera-socdk/board.c
index d7fb923a043b..f4b1dcd3249f 100644
--- a/arch/arm/boards/altera-socdk/board.c
+++ b/arch/arm/boards/altera-socdk/board.c
@@ -8,7 +8,7 @@
#include <linux/sizes.h>
#include <fcntl.h>
#include <fs.h>
-#include <mach/socfpga-regs.h>
+#include <mach/cyclone5-regs.h>
static int ksz9021rn_phy_fixup(struct phy_device *dev)
{
diff --git a/arch/arm/boards/altera-socdk/iocsr_config_cyclone5.c b/arch/arm/boards/altera-socdk/iocsr_config_cyclone5.c
index 07a4485f1fe6..9777d15dfebf 100644
--- a/arch/arm/boards/altera-socdk/iocsr_config_cyclone5.c
+++ b/arch/arm/boards/altera-socdk/iocsr_config_cyclone5.c
@@ -27,7 +27,7 @@
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
-#include <mach/scan-manager.h>
+#include <mach/cyclone5-scan-manager.h>
static const unsigned long iocsr_scan_chain0_table[((CONFIG_HPS_IOCSR_SCANCHAIN0_LENGTH / 32) + 1)]
= {
diff --git a/arch/arm/boards/altera-socdk/lowlevel.c b/arch/arm/boards/altera-socdk/lowlevel.c
index 02c995fe4522..8cfe8391596d 100644
--- a/arch/arm/boards/altera-socdk/lowlevel.c
+++ b/arch/arm/boards/altera-socdk/lowlevel.c
@@ -7,13 +7,13 @@
#include <debug_ll.h>
#include <asm/cache.h>
#include "sdram_config.h"
-#include <mach/sdram_config.h>
+#include <mach/cyclone5-sdram-config.h>
#include "pinmux_config.c"
#include "pll_config.h"
#include <mach/pll_config.h>
#include "sequencer_defines.h"
#include "sequencer_auto.h"
-#include <mach/sequencer.c>
+#include <mach/cyclone5-sequencer.c>
#include "sequencer_auto_inst_init.c"
#include "sequencer_auto_ac_init.c"
#include "iocsr_config_cyclone5.c"
diff --git a/arch/arm/boards/ebv-socrates/board.c b/arch/arm/boards/ebv-socrates/board.c
index f3207b88efdf..965150f9a3be 100644
--- a/arch/arm/boards/ebv-socrates/board.c
+++ b/arch/arm/boards/ebv-socrates/board.c
@@ -11,7 +11,7 @@
#include <linux/sizes.h>
#include <fcntl.h>
#include <fs.h>
-#include <mach/socfpga-regs.h>
+#include <mach/cyclone5-regs.h>
static int phy_fixup(struct phy_device *dev)
{
diff --git a/arch/arm/boards/ebv-socrates/iocsr_config_cyclone5.c b/arch/arm/boards/ebv-socrates/iocsr_config_cyclone5.c
index ab6733f92bcf..9a814cba796c 100644
--- a/arch/arm/boards/ebv-socrates/iocsr_config_cyclone5.c
+++ b/arch/arm/boards/ebv-socrates/iocsr_config_cyclone5.c
@@ -27,7 +27,7 @@
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
-#include <mach/scan-manager.h>
+#include <mach/cyclone5-scan-manager.h>
static const unsigned long iocsr_scan_chain0_table[((CONFIG_HPS_IOCSR_SCANCHAIN0_LENGTH / 32) + 1)] = {
0x00000000,
diff --git a/arch/arm/boards/ebv-socrates/lowlevel.c b/arch/arm/boards/ebv-socrates/lowlevel.c
index ea4e1d746a95..9643269f8e16 100644
--- a/arch/arm/boards/ebv-socrates/lowlevel.c
+++ b/arch/arm/boards/ebv-socrates/lowlevel.c
@@ -7,13 +7,13 @@
#include <mach/generic.h>
#include <debug_ll.h>
#include "sdram_config.h"
-#include <mach/sdram_config.h>
+#include <mach/cyclone5-sdram-config.h>
#include "pinmux_config.c"
#include "pll_config.h"
#include <mach/pll_config.h>
#include "sequencer_defines.h"
#include "sequencer_auto.h"
-#include <mach/sequencer.c>
+#include <mach/cyclone5-sequencer.c>
#include "sequencer_auto_inst_init.c"
#include "sequencer_auto_ac_init.c"
#include "iocsr_config_cyclone5.c"
diff --git a/arch/arm/boards/terasic-de0-nano-soc/board.c b/arch/arm/boards/terasic-de0-nano-soc/board.c
index 919bfc8c543a..8e69319d17b8 100644
--- a/arch/arm/boards/terasic-de0-nano-soc/board.c
+++ b/arch/arm/boards/terasic-de0-nano-soc/board.c
@@ -8,7 +8,7 @@
#include <linux/sizes.h>
#include <fcntl.h>
#include <fs.h>
-#include <mach/socfpga-regs.h>
+#include <mach/cyclone5-regs.h>
static int phy_fixup(struct phy_device *dev)
{
diff --git a/arch/arm/boards/terasic-de0-nano-soc/iocsr_config_cyclone5.c b/arch/arm/boards/terasic-de0-nano-soc/iocsr_config_cyclone5.c
index 4e9ac7fb7721..d5098055ff63 100644
--- a/arch/arm/boards/terasic-de0-nano-soc/iocsr_config_cyclone5.c
+++ b/arch/arm/boards/terasic-de0-nano-soc/iocsr_config_cyclone5.c
@@ -27,7 +27,7 @@
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
-#include <mach/scan-manager.h>
+#include <mach/cyclone5-scan-manager.h>
static const unsigned long iocsr_scan_chain0_table[((CONFIG_HPS_IOCSR_SCANCHAIN0_LENGTH / 32) + 1)] = {
0x00000000,
diff --git a/arch/arm/boards/terasic-de0-nano-soc/lowlevel.c b/arch/arm/boards/terasic-de0-nano-soc/lowlevel.c
index 6d937abda589..1d5ea6b12a52 100644
--- a/arch/arm/boards/terasic-de0-nano-soc/lowlevel.c
+++ b/arch/arm/boards/terasic-de0-nano-soc/lowlevel.c
@@ -7,13 +7,13 @@
#include <debug_ll.h>
#include <asm/cache.h>
#include "sdram_config.h"
-#include <mach/sdram_config.h>
+#include <mach/cyclone5-sdram-config.h>
#include "pinmux_config.c"
#include "pll_config.h"
#include <mach/pll_config.h>
#include "sequencer_defines.h"
#include "sequencer_auto.h"
-#include <mach/sequencer.c>
+#include <mach/cyclone5-sequencer.c>
#include "sequencer_auto_inst_init.c"
#include "sequencer_auto_ac_init.c"
#include "iocsr_config_cyclone5.c"
diff --git a/arch/arm/boards/terasic-sockit/board.c b/arch/arm/boards/terasic-sockit/board.c
index 53cd36834fc1..ec6831599803 100644
--- a/arch/arm/boards/terasic-sockit/board.c
+++ b/arch/arm/boards/terasic-sockit/board.c
@@ -8,7 +8,6 @@
#include <linux/sizes.h>
#include <fcntl.h>
#include <fs.h>
-#include <mach/socfpga-regs.h>
static int phy_fixup(struct phy_device *dev)
{
diff --git a/arch/arm/boards/terasic-sockit/iocsr_config_cyclone5.c b/arch/arm/boards/terasic-sockit/iocsr_config_cyclone5.c
index 117d7f4ebcc9..9367b0d11072 100644
--- a/arch/arm/boards/terasic-sockit/iocsr_config_cyclone5.c
+++ b/arch/arm/boards/terasic-sockit/iocsr_config_cyclone5.c
@@ -27,7 +27,7 @@
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
-#include <mach/scan-manager.h>
+#include <mach/cyclone5-scan-manager.h>
static const unsigned long iocsr_scan_chain0_table[((CONFIG_HPS_IOCSR_SCANCHAIN0_LENGTH / 32) + 1)] = {
0x00000000,
diff --git a/arch/arm/boards/terasic-sockit/lowlevel.c b/arch/arm/boards/terasic-sockit/lowlevel.c
index 8012783df3f8..0a6eb2136517 100644
--- a/arch/arm/boards/terasic-sockit/lowlevel.c
+++ b/arch/arm/boards/terasic-sockit/lowlevel.c
@@ -7,13 +7,13 @@
#include <debug_ll.h>
#include <asm/cache.h>
#include "sdram_config.h"
-#include <mach/sdram_config.h>
+#include <mach/cyclone5-sdram-config.h>
#include "pinmux_config.c"
#include "pll_config.h"
#include <mach/pll_config.h>
#include "sequencer_defines.h"
#include "sequencer_auto.h"
-#include <mach/sequencer.c>
+#include <mach/cyclone5-sequencer.c>
#include "sequencer_auto_inst_init.c"
#include "sequencer_auto_ac_init.c"
#include "iocsr_config_cyclone5.c"
diff --git a/arch/arm/mach-socfpga/Makefile b/arch/arm/mach-socfpga/Makefile
index dea0e075d145..30b796dd3b4f 100644
--- a/arch/arm/mach-socfpga/Makefile
+++ b/arch/arm/mach-socfpga/Makefile
@@ -1,4 +1,4 @@
-obj-y += generic.o nic301.o bootsource.o reset-manager.o
-pbl-y += init.o freeze-controller.o scan-manager.o system-manager.o
-pbl-y += clock-manager.o
+pbl-y += cyclone5-init.o cyclone5-freeze-controller.o cyclone5-scan-manager.o cyclone5-system-manager.o
+pbl-y += cyclone5-clock-manager.o
+obj-y += cyclone5-generic.o nic301.o cyclone5-bootsource.o cyclone5-reset-manager.o
obj-$(CONFIG_ARCH_SOCFPGA_XLOAD) += xload.o
diff --git a/arch/arm/mach-socfpga/bootsource.c b/arch/arm/mach-socfpga/cyclone5-bootsource.c
similarity index 79%
rename from arch/arm/mach-socfpga/bootsource.c
rename to arch/arm/mach-socfpga/cyclone5-bootsource.c
index 739f0b5c0e94..da4102c4f531 100644
--- a/arch/arm/mach-socfpga/bootsource.c
+++ b/arch/arm/mach-socfpga/cyclone5-bootsource.c
@@ -16,17 +16,17 @@
#include <environment.h>
#include <init.h>
#include <io.h>
-#include <mach/socfpga-regs.h>
-#include <mach/system-manager.h>
+#include <mach/cyclone5-system-manager.h>
+#include <mach/cyclone5-regs.h>
-#define SYSMGR_BOOTINFO 0x14
+#define CYCLONE5_SYSMGR_BOOTINFO 0x14
-static int socfpga_boot_save_loc(void)
+static int cyclone5_boot_save_loc(void)
{
enum bootsource src = BOOTSOURCE_UNKNOWN;
uint32_t val;
- val = readl(CYCLONE5_SYSMGR_ADDRESS + SYSMGR_BOOTINFO);
+ val = readl(CYCLONE5_SYSMGR_ADDRESS + CYCLONE5_SYSMGR_BOOTINFO);
switch (val & 0x7) {
case 0:
@@ -54,4 +54,4 @@ static int socfpga_boot_save_loc(void)
return 0;
}
-core_initcall(socfpga_boot_save_loc);
+core_initcall(cyclone5_boot_save_loc);
diff --git a/arch/arm/mach-socfpga/clock-manager.c b/arch/arm/mach-socfpga/cyclone5-clock-manager.c
similarity index 99%
rename from arch/arm/mach-socfpga/clock-manager.c
rename to arch/arm/mach-socfpga/cyclone5-clock-manager.c
index f17371365fe4..79c8b6bf2874 100644
--- a/arch/arm/mach-socfpga/clock-manager.c
+++ b/arch/arm/mach-socfpga/cyclone5-clock-manager.c
@@ -17,8 +17,8 @@
#include <common.h>
#include <io.h>
-#include <mach/clock-manager.h>
-#include <mach/socfpga-regs.h>
+#include <mach/cyclone5-clock-manager.h>
+#include <mach/cyclone5-regs.h>
#include <mach/generic.h>
static inline void cm_wait_for_lock(void __iomem *cm, uint32_t mask)
diff --git a/arch/arm/mach-socfpga/freeze-controller.c b/arch/arm/mach-socfpga/cyclone5-freeze-controller.c
similarity index 99%
rename from arch/arm/mach-socfpga/freeze-controller.c
rename to arch/arm/mach-socfpga/cyclone5-freeze-controller.c
index 570bdeb7353f..87160161b0e6 100644
--- a/arch/arm/mach-socfpga/freeze-controller.c
+++ b/arch/arm/mach-socfpga/cyclone5-freeze-controller.c
@@ -18,7 +18,7 @@
#include <common.h>
#include <io.h>
#include <mach/generic.h>
-#include <mach/freeze-controller.h>
+#include <mach/cyclone5-freeze-controller.h>
#define SYSMGR_FRZCTRL_LOOP_PARAM (1000)
#define SYSMGR_FRZCTRL_DELAY_LOOP_PARAM (10)
diff --git a/arch/arm/mach-socfpga/cyclone5-generic.c b/arch/arm/mach-socfpga/cyclone5-generic.c
new file mode 100644
index 000000000000..3f49a9a542eb
--- /dev/null
+++ b/arch/arm/mach-socfpga/cyclone5-generic.c
@@ -0,0 +1,210 @@
+#include <common.h>
+#include <malloc.h>
+#include <envfs.h>
+#include <init.h>
+#include <io.h>
+#include <fs.h>
+#include <mci.h>
+#include <linux/clkdev.h>
+#include <linux/clk.h>
+#include <linux/stat.h>
+#include <linux/sizes.h>
+#include <asm/memory.h>
+#include <mach/cyclone5-system-manager.h>
+#include <mach/cyclone5-reset-manager.h>
+#include <mach/cyclone5-regs.h>
+#include <mach/generic.h>
+#include <mach/nic301.h>
+#include <platform_data/dw_mmc.h>
+#include <platform_data/serial-ns16550.h>
+#include <platform_data/cadence_qspi.h>
+
+#define SYSMGR_SDMMCGRP_CTRL_REG (CYCLONE5_SYSMGR_ADDRESS + 0x108)
+#define SYSMGR_SDMMC_CTRL_SMPLSEL(smplsel) (((smplsel) & 0x7) << 3)
+#define SYSMGR_SDMMC_CTRL_DRVSEL(drvsel) ((drvsel) & 0x7)
+
+enum socfpga_clks {
+ timer, mmc, qspi_clk, uart, clk_max
+};
+
+static struct clk *clks[clk_max];
+
+#if defined(CONFIG_MCI_DW)
+static struct dw_mmc_platform_data mmc_pdata = {
+ .bus_width_caps = MMC_CAP_4_BIT_DATA,
+ .ciu_div = 3,
+};
+
+void socfpga_cyclone5_mmc_init(void)
+{
+ clks[mmc] = clk_fixed("mmc", 400000000);
+ clkdev_add_physbase(clks[mmc], CYCLONE5_SDMMC_ADDRESS, NULL);
+ add_generic_device("dw_mmc", 0, NULL, CYCLONE5_SDMMC_ADDRESS, SZ_4K,
+ IORESOURCE_MEM, &mmc_pdata);
+}
+#else
+void socfpga_cyclone5_mmc_init(void)
+{
+ pr_debug("%s: MMC support not compiled in!\n", __func__);
+
+ return;
+}
+#endif
+
+#if defined(CONFIG_SPI_CADENCE_QUADSPI)
+static struct cadence_qspi_platform_data qspi_pdata = {
+ .ext_decoder = 0,
+ .fifo_depth = 128,
+};
+
+static void add_cadence_qspi_device(int id, resource_size_t ctrl,
+ resource_size_t data, void *pdata)
+{
+ struct device_d *dev;
+ struct resource *res;
+
+ res = xzalloc(sizeof(struct resource) * 2);
+ res[0].start = ctrl;
+ res[0].end = ctrl + 0x100 - 1;
+ res[0].flags = IORESOURCE_MEM;
+ res[1].start = data;
+ res[1].end = data + 0x100 - 1;
+ res[1].flags = IORESOURCE_MEM;
+
+ dev = add_generic_device_res("cadence_qspi", id, res, 2, pdata);
+
+ dev_dbg(dev, "added resource\n");
+}
+
+void socfpga_cyclone5_qspi_init(void)
+{
+ clks[qspi_clk] = clk_fixed("qspi_clk", 370000000);
+ clkdev_add_physbase(clks[qspi_clk], CYCLONE5_QSPI_CTRL_ADDRESS, NULL);
+ clkdev_add_physbase(clks[qspi_clk], CYCLONE5_QSPI_DATA_ADDRESS, NULL);
+ add_cadence_qspi_device(0, CYCLONE5_QSPI_CTRL_ADDRESS,
+ CYCLONE5_QSPI_DATA_ADDRESS, &qspi_pdata);
+}
+#else
+void socfpga_cyclone5_qspi_init(void)
+{
+ pr_debug("%s: QSPI support not compiled in!\n", __func__);
+
+ return;
+}
+#endif
+
+static struct NS16550_plat uart_pdata = {
+ .clock = 100000000,
+ .shift = 2,
+};
+
+void socfpga_cyclone5_uart_init(void)
+{
+ struct device_d *dev;
+
+ clks[uart] = clk_fixed("uart", 100000000);
+ clkdev_add_physbase(clks[uart], CYCLONE5_UART0_ADDRESS, NULL);
+ clkdev_add_physbase(clks[uart], CYCLONE5_UART1_ADDRESS, NULL);
+ dev = add_ns16550_device(0, 0xffc02000, 1024, IORESOURCE_MEM |
+ IORESOURCE_MEM_8BIT, &uart_pdata);
+
+ dev_dbg(dev, "initialized\n");
+}
+
+void socfpga_cyclone5_timer_init(void)
+{
+ struct device_d *dev;
+
+ clks[timer] = clk_fixed("timer", 200000000);
+ clkdev_add_physbase(clks[timer], CYCLONE5_SMP_TWD_ADDRESS, NULL);
+ dev = add_generic_device("smp_twd", 0, NULL, CYCLONE5_SMP_TWD_ADDRESS, 0x100,
+ IORESOURCE_MEM, NULL);
+
+ dev_dbg(dev, "added smp_twd\n");
+}
+
+static int socfpga_detect_sdram(void)
+{
+ void __iomem *base = (void *)CYCLONE5_SDR_ADDRESS;
+ uint32_t dramaddrw, ctrlwidth, memsize;
+ int colbits, rowbits, bankbits;
+ int width_bytes;
+
+ dramaddrw = readl(base + 0x5000 + 0x2c);
+
+ colbits = dramaddrw & 0x1f;
+ rowbits = (dramaddrw >> 5) & 0x1f;
+ bankbits = (dramaddrw >> 10) & 0x7;
+
+ ctrlwidth = readl(base + 0x5000 + 0x60);
+
+ switch (ctrlwidth & 0x3) {
+ default:
+ case 0:
+ width_bytes = 1;
+ break;
+ case 1:
+ width_bytes = 2;
+ break;
+ case 2:
+ width_bytes = 4;
+ break;
+ }
+
+ memsize = (1 << colbits) * (1 << rowbits) * (1 << bankbits) * width_bytes;
+
+ pr_debug("%s: colbits: %d rowbits: %d bankbits: %d width: %d => memsize: 0x%08x\n",
+ __func__, colbits, rowbits, bankbits, width_bytes, memsize);
+
+ arm_add_mem_device("ram0", 0x0, memsize);
+
+ return 0;
+}
+
+/* Some initialization for the EMAC */
+static void socfpga_init_emac(void)
+{
+ uint32_t rst, val;
+
+ /* No need for this without network support, e.g. xloader build */
+ if (!IS_ENABLED(CONFIG_NET))
+ return;
+
+ /* According to Cyclone V datasheet, 17-60 "EMAC HPS Interface
+ * Initialization", changing PHYSEL should be done with EMAC in reset
+ * via permodrst. */
+
+ /* Everything, except L4WD0/1, is out of reset via socfpga_lowlevel_init() */
+ rst = readl(CYCLONE5_RSTMGR_ADDRESS + RESET_MGR_PER_MOD_RESET_OFS);
+ rst |= RSTMGR_PERMODRST_EMAC0 | RSTMGR_PERMODRST_EMAC1;
+ writel(rst, CYCLONE5_RSTMGR_ADDRESS + RESET_MGR_PER_MOD_RESET_OFS);
+
+ /* Set emac0/1 PHY interface select to RGMII. We could read phy-mode
+ * from the device tree, if it was desired to support interfaces other
+ * than RGMII. */
+ val = readl(CONFIG_SYSMGR_EMAC_CTRL);
+ val &= ~(SYSMGR_EMACGRP_CTRL_PHYSEL_MASK << SYSMGR_EMACGRP_CTRL_PHYSEL0_LSB);
+ val &= ~(SYSMGR_EMACGRP_CTRL_PHYSEL_MASK << SYSMGR_EMACGRP_CTRL_PHYSEL1_LSB);
+ val |= SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_RGMII << SYSMGR_EMACGRP_CTRL_PHYSEL0_LSB;
+ val |= SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_RGMII << SYSMGR_EMACGRP_CTRL_PHYSEL1_LSB;
+ writel(val, CONFIG_SYSMGR_EMAC_CTRL);
+
+ /* Take emac0 and emac1 out of reset */
+ rst &= ~(RSTMGR_PERMODRST_EMAC0 | RSTMGR_PERMODRST_EMAC1);
+ writel(rst, CYCLONE5_RSTMGR_ADDRESS + RESET_MGR_PER_MOD_RESET_OFS);
+}
+
+static int socfpga_init(void)
+{
+ socfpga_init_emac();
+
+ writel(SYSMGR_SDMMC_CTRL_DRVSEL(3) | SYSMGR_SDMMC_CTRL_SMPLSEL(0),
+ SYSMGR_SDMMCGRP_CTRL_REG);
+
+ nic301_slave_ns();
+
+ socfpga_detect_sdram();
+
+ return 0;
+}
+core_initcall(socfpga_init);
diff --git a/arch/arm/mach-socfpga/init.c b/arch/arm/mach-socfpga/cyclone5-init.c
similarity index 89%
rename from arch/arm/mach-socfpga/init.c
rename to arch/arm/mach-socfpga/cyclone5-init.c
index 0c679e3d2dac..412808b8416f 100644
--- a/arch/arm/mach-socfpga/init.c
+++ b/arch/arm/mach-socfpga/cyclone5-init.c
@@ -2,11 +2,11 @@
#include <common.h>
#include <init.h>
#include <io.h>
-#include <mach/freeze-controller.h>
-#include <mach/system-manager.h>
-#include <mach/clock-manager.h>
-#include <mach/reset-manager.h>
-#include <mach/scan-manager.h>
+#include <mach/cyclone5-freeze-controller.h>
+#include <mach/cyclone5-system-manager.h>
+#include <mach/cyclone5-clock-manager.h>
+#include <mach/cyclone5-reset-manager.h>
+#include <mach/cyclone5-scan-manager.h>
#include <mach/generic.h>
void socfpga_lowlevel_init(struct socfpga_cm_config *cm_config,
diff --git a/arch/arm/mach-socfpga/reset-manager.c b/arch/arm/mach-socfpga/cyclone5-reset-manager.c
similarity index 96%
rename from arch/arm/mach-socfpga/reset-manager.c
rename to arch/arm/mach-socfpga/cyclone5-reset-manager.c
index 04522da4d1ae..4bbe1a8101f1 100644
--- a/arch/arm/mach-socfpga/reset-manager.c
+++ b/arch/arm/mach-socfpga/cyclone5-reset-manager.c
@@ -19,8 +19,8 @@
#include <io.h>
#include <init.h>
#include <restart.h>
-#include <mach/socfpga-regs.h>
-#include <mach/reset-manager.h>
+#include <mach/cyclone5-regs.h>
+#include <mach/cyclone5-reset-manager.h>
/* Disable the watchdog (toggle reset to watchdog) */
void watchdog_disable(void)
diff --git a/arch/arm/mach-socfpga/scan-manager.c b/arch/arm/mach-socfpga/cyclone5-scan-manager.c
similarity index 98%
rename from arch/arm/mach-socfpga/scan-manager.c
rename to arch/arm/mach-socfpga/cyclone5-scan-manager.c
index 57979b90a208..cf076c3885b3 100644
--- a/arch/arm/mach-socfpga/scan-manager.c
+++ b/arch/arm/mach-socfpga/cyclone5-scan-manager.c
@@ -17,8 +17,8 @@
#include <common.h>
#include <io.h>
-#include <mach/freeze-controller.h>
-#include <mach/scan-manager.h>
+#include <mach/cyclone5-freeze-controller.h>
+#include <mach/cyclone5-scan-manager.h>
/*
* @fn scan_mgr_io_scan_chain_engine_is_idle
diff --git a/arch/arm/mach-socfpga/system-manager.c b/arch/arm/mach-socfpga/cyclone5-system-manager.c
similarity index 93%
rename from arch/arm/mach-socfpga/system-manager.c
rename to arch/arm/mach-socfpga/cyclone5-system-manager.c
index 45db921f1a02..7e86692c397e 100644
--- a/arch/arm/mach-socfpga/system-manager.c
+++ b/arch/arm/mach-socfpga/cyclone5-system-manager.c
@@ -17,8 +17,8 @@
#include <common.h>
#include <io.h>
-#include <mach/system-manager.h>
-#include <mach/socfpga-regs.h>
+#include <mach/cyclone5-system-manager.h>
+#include <mach/cyclone5-regs.h>
void socfpga_sysmgr_pinmux_init(unsigned long *sys_mgr_init_table, int num)
{
diff --git a/arch/arm/mach-socfpga/include/mach/clock-manager.h b/arch/arm/mach-socfpga/include/mach/cyclone5-clock-manager.h
similarity index 99%
rename from arch/arm/mach-socfpga/include/mach/clock-manager.h
rename to arch/arm/mach-socfpga/include/mach/cyclone5-clock-manager.h
index 45800de79a7a..797aa5d3cfe8 100644
--- a/arch/arm/mach-socfpga/include/mach/clock-manager.h
+++ b/arch/arm/mach-socfpga/include/mach/cyclone5-clock-manager.h
@@ -15,8 +15,8 @@
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
-#ifndef _CLOCK_MANAGER_H_
-#define _CLOCK_MANAGER_H_
+#ifndef _CLOCK_MANAGER_CYCLONE5_H_
+#define _CLOCK_MANAGER_CYCLONE5_H_
struct socfpga_cm_config {
/* main group */
@@ -197,4 +197,4 @@ void socfpga_cm_basic_init(const struct socfpga_cm_config *cfg);
CLKMGR_MAINPLLGRP_VCO_EN_SET(0)| \
CLKMGR_MAINPLLGRP_VCO_BGPWRDN_SET(0))
-#endif /* _CLOCK_MANAGER_H_ */
+#endif
diff --git a/arch/arm/mach-socfpga/include/mach/freeze-controller.h b/arch/arm/mach-socfpga/include/mach/cyclone5-freeze-controller.h
similarity index 96%
rename from arch/arm/mach-socfpga/include/mach/freeze-controller.h
rename to arch/arm/mach-socfpga/include/mach/cyclone5-freeze-controller.h
index 4253f5b38f92..93ce5152eda9 100644
--- a/arch/arm/mach-socfpga/include/mach/freeze-controller.h
+++ b/arch/arm/mach-socfpga/include/mach/cyclone5-freeze-controller.h
@@ -15,10 +15,10 @@
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
-#ifndef _FREEZE_CONTROLLER_H_
-#define _FREEZE_CONTROLLER_H_
+#ifndef _CYCLONE5_FREEZE_CONTROLLER_H_
+#define _CYCLONE5_FREEZE_CONTROLLER_H_
-#include <mach/socfpga-regs.h>
+#include <mach/cyclone5-regs.h>
#define SYSMGR_FRZCTRL_ADDRESS 0x40
#define SYSMGR_FRZCTRL_VIOCTRL_ADDRESS 0x40
diff --git a/arch/arm/mach-socfpga/include/mach/socfpga-regs.h b/arch/arm/mach-socfpga/include/mach/cyclone5-regs.h
similarity index 100%
rename from arch/arm/mach-socfpga/include/mach/socfpga-regs.h
rename to arch/arm/mach-socfpga/include/mach/cyclone5-regs.h
diff --git a/arch/arm/mach-socfpga/include/mach/reset-manager.h b/arch/arm/mach-socfpga/include/mach/cyclone5-reset-manager.h
similarity index 100%
rename from arch/arm/mach-socfpga/include/mach/reset-manager.h
rename to arch/arm/mach-socfpga/include/mach/cyclone5-reset-manager.h
diff --git a/arch/arm/mach-socfpga/include/mach/scan-manager.h b/arch/arm/mach-socfpga/include/mach/cyclone5-scan-manager.h
similarity index 99%
rename from arch/arm/mach-socfpga/include/mach/scan-manager.h
rename to arch/arm/mach-socfpga/include/mach/cyclone5-scan-manager.h
index 568bedfde13c..df720a7e086c 100644
--- a/arch/arm/mach-socfpga/include/mach/scan-manager.h
+++ b/arch/arm/mach-socfpga/include/mach/cyclone5-scan-manager.h
@@ -19,7 +19,7 @@
#define _SCAN_MANAGER_H_
#include <io.h>
-#include <mach/socfpga-regs.h>
+#include <mach/cyclone5-regs.h>
/***********************************************************
* *
diff --git a/arch/arm/mach-socfpga/include/mach/sdram_config.h b/arch/arm/mach-socfpga/include/mach/cyclone5-sdram-config.h
similarity index 98%
rename from arch/arm/mach-socfpga/include/mach/sdram_config.h
rename to arch/arm/mach-socfpga/include/mach/cyclone5-sdram-config.h
index 2af797a920d9..a19a837994e2 100644
--- a/arch/arm/mach-socfpga/include/mach/sdram_config.h
+++ b/arch/arm/mach-socfpga/include/mach/cyclone5-sdram-config.h
@@ -1,9 +1,9 @@
#ifndef __MACH_SDRAM_CONFIG_H
#define __MACH_SDRAM_CONFIG_H
-#include <mach/sdram.h>
-#include <mach/socfpga-regs.h>
-#include <mach/system-manager.h>
+#include <mach/cyclone5-sdram.h>
+#include <mach/cyclone5-regs.h>
+#include <mach/cyclone5-system-manager.h>
static inline void sdram_write(unsigned register_offset, unsigned val)
{
diff --git a/arch/arm/mach-socfpga/include/mach/sdram.h b/arch/arm/mach-socfpga/include/mach/cyclone5-sdram.h
similarity index 100%
rename from arch/arm/mach-socfpga/include/mach/sdram.h
rename to arch/arm/mach-socfpga/include/mach/cyclone5-sdram.h
diff --git a/arch/arm/mach-socfpga/include/mach/sequencer.c b/arch/arm/mach-socfpga/include/mach/cyclone5-sequencer.c
similarity index 99%
rename from arch/arm/mach-socfpga/include/mach/sequencer.c
rename to arch/arm/mach-socfpga/include/mach/cyclone5-sequencer.c
index d2338e640686..e5ecb0f1b8b5 100644
--- a/arch/arm/mach-socfpga/include/mach/sequencer.c
+++ b/arch/arm/mach-socfpga/include/mach/cyclone5-sequencer.c
@@ -26,11 +26,9 @@
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
-#include "sequencer_defines.h"
-
#include "system.h"
#include "sdram_io.h"
-#include "sequencer.h"
+#include "cyclone5-sequencer.h"
#include "tclrpt.h"
/******************************************************************************
@@ -57,7 +55,7 @@ asm(".global __alt_stack_pointer");
asm("__alt_stack_pointer = " STRINGIFY(STACK_POINTER));
#endif
-#include <mach/sdram.h>
+#include <mach/cyclone5-sdram.h>
#define NEWVERSION_RDDESKEW 1
#define NEWVERSION_WRDESKEW 1
diff --git a/arch/arm/mach-socfpga/include/mach/sequencer.h b/arch/arm/mach-socfpga/include/mach/cyclone5-sequencer.h
similarity index 100%
rename from arch/arm/mach-socfpga/include/mach/sequencer.h
rename to arch/arm/mach-socfpga/include/mach/cyclone5-sequencer.h
diff --git a/arch/arm/mach-socfpga/include/mach/system-manager.h b/arch/arm/mach-socfpga/include/mach/cyclone5-system-manager.h
similarity index 100%
rename from arch/arm/mach-socfpga/include/mach/system-manager.h
rename to arch/arm/mach-socfpga/include/mach/cyclone5-system-manager.h
diff --git a/arch/arm/mach-socfpga/include/mach/pll_config.h b/arch/arm/mach-socfpga/include/mach/pll_config.h
index bb491d82f12c..1a7e851eda43 100644
--- a/arch/arm/mach-socfpga/include/mach/pll_config.h
+++ b/arch/arm/mach-socfpga/include/mach/pll_config.h
@@ -1,5 +1,5 @@
-#include <mach/clock-manager.h>
+#include <mach/cyclone5-clock-manager.h>
static struct socfpga_cm_config cm_default_cfg = {
/* main group */
diff --git a/arch/arm/mach-socfpga/include/mach/sdram_io.h b/arch/arm/mach-socfpga/include/mach/sdram_io.h
old mode 100755
new mode 100644
index 62698000f6d8..ef87bdaf63b3
--- a/arch/arm/mach-socfpga/include/mach/sdram_io.h
+++ b/arch/arm/mach-socfpga/include/mach/sdram_io.h
@@ -26,7 +26,7 @@
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
-#include <mach/sdram.h>
+#include <mach/cyclone5-sdram.h>
#define MGR_SELECT_MASK 0xf8000
diff --git a/arch/arm/mach-socfpga/include/mach/sequencer_defines.h b/arch/arm/mach-socfpga/include/mach/sequencer_defines.h
deleted file mode 100644
index 50598441069d..000000000000
--- a/arch/arm/mach-socfpga/include/mach/sequencer_defines.h
+++ /dev/null
@@ -1,6 +0,0 @@
-#define TINIT_CNTR1_VAL 32
-#define TINIT_CNTR2_VAL 32
-#define TINIT_CNTR0_VAL 99
-#define TRESET_CNTR1_VAL 99
-#define TRESET_CNTR2_VAL 10
-#define TRESET_CNTR0_VAL 99
diff --git a/arch/arm/mach-socfpga/include/mach/system.h b/arch/arm/mach-socfpga/include/mach/system.h
old mode 100755
new mode 100644
diff --git a/arch/arm/mach-socfpga/include/mach/tclrpt.h b/arch/arm/mach-socfpga/include/mach/tclrpt.h
old mode 100755
new mode 100644
index 4345b23ba65c..6b332c875412
--- a/arch/arm/mach-socfpga/include/mach/tclrpt.h
+++ b/arch/arm/mach-socfpga/include/mach/tclrpt.h
@@ -28,7 +28,7 @@
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
-#include "sequencer.h"
+#include "cyclone5-sequencer.h"
#define TCLRPT_SET(item, value)
diff --git a/arch/arm/mach-socfpga/nic301.c b/arch/arm/mach-socfpga/nic301.c
index 206dd48ff911..7069c6e5b9ae 100644
--- a/arch/arm/mach-socfpga/nic301.c
+++ b/arch/arm/mach-socfpga/nic301.c
@@ -18,7 +18,7 @@
#include <common.h>
#include <io.h>
#include <mach/nic301.h>
-#include <mach/socfpga-regs.h>
+#include <mach/cyclone5-regs.h>
/*
* Convert all slave from secure to non secure
diff --git a/arch/arm/mach-socfpga/xload.c b/arch/arm/mach-socfpga/xload.c
index d24944bbb85e..5d47bb9d3ea2 100644
--- a/arch/arm/mach-socfpga/xload.c
+++ b/arch/arm/mach-socfpga/xload.c
@@ -17,8 +17,8 @@
#include <linux/clk.h>
#include <mach/generic.h>
-#include <mach/system-manager.h>
-#include <mach/socfpga-regs.h>
+#include <mach/cyclone5-system-manager.h>
+#include <mach/cyclone5-regs.h>
static struct socfpga_barebox_part default_parts[] = {
{
diff --git a/drivers/firmware/socfpga.c b/drivers/firmware/socfpga.c
index a0cd2011cbce..c1eae98acc91 100644
--- a/drivers/firmware/socfpga.c
+++ b/drivers/firmware/socfpga.c
@@ -34,10 +34,10 @@
#include <fcntl.h>
#include <init.h>
#include <io.h>
-#include <mach/system-manager.h>
-#include <mach/reset-manager.h>
-#include <mach/socfpga-regs.h>
-#include <mach/sdram.h>
+#include <mach/cyclone5-system-manager.h>
+#include <mach/cyclone5-reset-manager.h>
+#include <mach/cyclone5-regs.h>
+#include <mach/cyclone5-sdram.h>
#define FPGAMGRREGS_STAT 0x0
#define FPGAMGRREGS_CTRL 0x4
diff --git a/scripts/socfpga_import_preloader b/scripts/socfpga_import_preloader
index b08262cb6c83..63ff30ec2a21 100755
--- a/scripts/socfpga_import_preloader
+++ b/scripts/socfpga_import_preloader
@@ -46,7 +46,7 @@ copy_source() {
echo " Fixing include pathes..."
# Fix include pathes
- sed -i 's/#include <iocsr_config_cyclone5.h>/#include <mach\/scan-manager.h>/g' $tgt
+ sed -i 's/#include <iocsr_config_cyclone5.h>/#include <mach\/cyclone5-scan-manager.h>/g' $tgt
sed -i 's/#include <pinmux_config.h>/#include <common.h>/g' $tgt
sed -i 's/#include "sequencer_auto.h"//g' $tgt
sed -i 's/#include "sequencer_defines.h"//g' $tgt
--
2.11.0
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 12+ messages in thread* [PATCH 4/7] ARM: socfpga: add arria10 support
2017-04-03 10:55 [PATCH 0/7] SoCFPGA: add support for Arria10 Steffen Trumtrar
` (2 preceding siblings ...)
2017-04-03 10:55 ` [PATCH 3/7] net: designware: add dwmac-3.72a compatible Steffen Trumtrar
@ 2017-04-03 10:55 ` Steffen Trumtrar
2017-04-04 18:58 ` Trent Piepho
2017-04-03 10:55 ` [PATCH 5/7] clk: socfpga: add arria10 clk drivers Steffen Trumtrar
` (3 subsequent siblings)
7 siblings, 1 reply; 12+ messages in thread
From: Steffen Trumtrar @ 2017-04-03 10:55 UTC (permalink / raw)
To: barebox; +Cc: Steffen Trumtrar
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
---
arch/arm/Kconfig | 6 +-
arch/arm/mach-socfpga/Kconfig | 18 +
arch/arm/mach-socfpga/Makefile | 10 +-
arch/arm/mach-socfpga/arria10-bootsource.c | 53 ++
arch/arm/mach-socfpga/arria10-clock-manager.c | 807 +++++++++++++++++++++
arch/arm/mach-socfpga/arria10-generic.c | 85 +++
arch/arm/mach-socfpga/arria10-init.c | 275 +++++++
arch/arm/mach-socfpga/arria10-reset-manager.c | 422 +++++++++++
arch/arm/mach-socfpga/arria10-sdram.c | 557 ++++++++++++++
arch/arm/mach-socfpga/cyclone5-bootsource.c | 45 +-
arch/arm/mach-socfpga/generic.c | 104 ---
.../include/mach/arria10-clock-manager.h | 249 +++++++
.../arm/mach-socfpga/include/mach/arria10-pinmux.h | 128 ++++
arch/arm/mach-socfpga/include/mach/arria10-regs.h | 114 +++
.../include/mach/arria10-reset-manager.h | 119 +++
arch/arm/mach-socfpga/include/mach/arria10-sdram.h | 353 +++++++++
.../include/mach/arria10-system-manager.h | 97 +++
arch/arm/mach-socfpga/include/mach/generic.h | 35 +
arch/arm/mach-socfpga/xload.c | 92 +--
images/Makefile.socfpga | 8 +
scripts/socfpga_mkimage.c | 1 +
scripts/socfpga_xml_to_config.sh | 86 +++
22 files changed, 3465 insertions(+), 199 deletions(-)
create mode 100644 arch/arm/mach-socfpga/arria10-bootsource.c
create mode 100644 arch/arm/mach-socfpga/arria10-clock-manager.c
create mode 100644 arch/arm/mach-socfpga/arria10-generic.c
create mode 100644 arch/arm/mach-socfpga/arria10-init.c
create mode 100644 arch/arm/mach-socfpga/arria10-reset-manager.c
create mode 100644 arch/arm/mach-socfpga/arria10-sdram.c
delete mode 100644 arch/arm/mach-socfpga/generic.c
create mode 100644 arch/arm/mach-socfpga/include/mach/arria10-clock-manager.h
create mode 100644 arch/arm/mach-socfpga/include/mach/arria10-pinmux.h
create mode 100644 arch/arm/mach-socfpga/include/mach/arria10-regs.h
create mode 100644 arch/arm/mach-socfpga/include/mach/arria10-reset-manager.h
create mode 100644 arch/arm/mach-socfpga/include/mach/arria10-sdram.h
create mode 100644 arch/arm/mach-socfpga/include/mach/arria10-system-manager.h
create mode 100755 scripts/socfpga_xml_to_config.sh
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index e4663ea26872..61c7d6c275f8 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -176,7 +176,7 @@ config ARCH_ROCKCHIP
select ARCH_HAS_L2X0
config ARCH_SOCFPGA
- bool "Altera SOCFPGA cyclone5"
+ bool "Altera SOCFPGA"
select HAS_DEBUG_LL
select ARM_SMP_TWD
select CPU_V7
@@ -184,8 +184,8 @@ config ARCH_SOCFPGA
select CLKDEV_LOOKUP
select GPIOLIB
select HAVE_PBL_MULTI_IMAGES
- select OFDEVICE if !ARCH_SOCFPGA_XLOAD
- select OFTREE if !ARCH_SOCFPGA_XLOAD
+ select OFDEVICE if !(ARCH_SOCFPGA_XLOAD && ARCH_SOCFPGA_CYCLONE5)
+ select OFTREE if !(ARCH_SOCFPGA_XLOAD && ARCH_SOCFPGA_CYCLONE5)
config ARCH_S3C24xx
bool "Samsung S3C2410, S3C2440"
diff --git a/arch/arm/mach-socfpga/Kconfig b/arch/arm/mach-socfpga/Kconfig
index 04b5416b6452..003574ba8d65 100644
--- a/arch/arm/mach-socfpga/Kconfig
+++ b/arch/arm/mach-socfpga/Kconfig
@@ -12,16 +12,34 @@ config ARCH_TEXT_BASE
hex
default 0x00100000 if MACH_SOCFPGA_CYCLONE5
+comment "Altera SoCFPGA System-on-Chip"
+
+config ARCH_SOCFPGA_CYCLONE5
+ bool
+ select CPU_V7
+
+config ARCH_SOCFPGA_ARRIA10
+ bool
+ select CPU_V7
+
config MACH_SOCFPGA_ALTERA_SOCDK
+ select HAVE_DEFAULT_ENVIRONMENT_NEW
+ select ARCH_SOCFPGA_CYCLONE5
bool "Altera SoCFPGA Development Kit"
config MACH_SOCFPGA_EBV_SOCRATES
+ select HAVE_DEFAULT_ENVIRONMENT_NEW
+ select ARCH_SOCFPGA_CYCLONE5
bool "EBV Socrates"
config MACH_SOCFPGA_TERASIC_DE0_NANO_SOC
+ select HAVE_DEFAULT_ENVIRONMENT_NEW
+ select ARCH_SOCFPGA_CYCLONE5
bool "Terasic DE0-NANO-SoC aka Atlas"
config MACH_SOCFPGA_TERASIC_SOCKIT
+ select HAVE_DEFAULT_ENVIRONMENT_NEW
+ select ARCH_SOCFPGA_CYCLONE5
bool "Terasic SoCKit"
endif
diff --git a/arch/arm/mach-socfpga/Makefile b/arch/arm/mach-socfpga/Makefile
index 30b796dd3b4f..cbb47fa206f2 100644
--- a/arch/arm/mach-socfpga/Makefile
+++ b/arch/arm/mach-socfpga/Makefile
@@ -1,4 +1,8 @@
-pbl-y += cyclone5-init.o cyclone5-freeze-controller.o cyclone5-scan-manager.o cyclone5-system-manager.o
-pbl-y += cyclone5-clock-manager.o
-obj-y += cyclone5-generic.o nic301.o cyclone5-bootsource.o cyclone5-reset-manager.o
+pbl-$(CONFIG_ARCH_SOCFPGA_CYCLONE5) += cyclone5-init.o cyclone5-freeze-controller.o cyclone5-scan-manager.o cyclone5-system-manager.o
+pbl-$(CONFIG_ARCH_SOCFPGA_CYCLONE5) += cyclone5-clock-manager.o
+obj-$(CONFIG_ARCH_SOCFPGA_CYCLONE5) += cyclone5-generic.o nic301.o cyclone5-bootsource.o cyclone5-reset-manager.o
+
+pbl-$(CONFIG_ARCH_SOCFPGA_ARRIA10) += arria10-init.o arria10-clock-manager.o arria10-sdram.o arria10-reset-manager.o arria10-bootsource.o
+obj-$(CONFIG_ARCH_SOCFPGA_ARRIA10) += arria10-bootsource.o arria10-generic.o arria10-reset-manager.o
+
obj-$(CONFIG_ARCH_SOCFPGA_XLOAD) += xload.o
diff --git a/arch/arm/mach-socfpga/arria10-bootsource.c b/arch/arm/mach-socfpga/arria10-bootsource.c
new file mode 100644
index 000000000000..26af64a1a408
--- /dev/null
+++ b/arch/arm/mach-socfpga/arria10-bootsource.c
@@ -0,0 +1,53 @@
+/*
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <common.h>
+#include <bootsource.h>
+#include <init.h>
+#include <io.h>
+#include <mach/arria10-system-manager.h>
+
+static int arria10_boot_save_loc(void)
+{
+ enum bootsource src = BOOTSOURCE_UNKNOWN;
+ uint32_t val;
+
+ val = readl(ARRIA10_SYSMGR_BOOTINFO);
+
+ switch ((val & 0x7000) >> 12) {
+ case 0:
+ /* reserved */
+ break;
+ case 1:
+ /* FPGA, currently not decoded */
+ break;
+ case 2:
+ case 3:
+ src = BOOTSOURCE_NAND;
+ break;
+ case 4:
+ case 5:
+ src = BOOTSOURCE_MMC;
+ break;
+ case 6:
+ case 7:
+ src = BOOTSOURCE_SPI;
+ break;
+ }
+
+ bootsource_set(src);
+ bootsource_set_instance(0);
+
+ return 0;
+}
+core_initcall(arria10_boot_save_loc);
diff --git a/arch/arm/mach-socfpga/arria10-clock-manager.c b/arch/arm/mach-socfpga/arria10-clock-manager.c
new file mode 100644
index 000000000000..d0c442ad1bf5
--- /dev/null
+++ b/arch/arm/mach-socfpga/arria10-clock-manager.c
@@ -0,0 +1,807 @@
+/*
+ * Copyright (C) 2014 Altera Corporation <www.altera.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <mach/arria10-regs.h>
+#include <mach/arria10-clock-manager.h>
+
+static const struct arria10_clock_manager *arria10_clkmgr_base =
+ (void *)ARRIA10_CLKMGR_ADDR;
+
+static uint32_t eosc1_hz;
+static uint32_t cb_intosc_hz;
+static uint32_t f2s_free_hz;
+#define LOCKED_MASK (ARRIA10_CLKMGR_CLKMGR_STAT_MAINPLLLOCKED_SET_MSK | \
+ ARRIA10_CLKMGR_CLKMGR_STAT_PERPLLLOCKED_SET_MSK)
+
+static inline void arria10_cm_wait_for_lock(uint32_t mask)
+{
+ register uint32_t inter_val;
+
+ do {
+ inter_val = readl(&arria10_clkmgr_base->stat) & mask;
+ } while (inter_val != mask);
+}
+
+/* function to poll in the fsm busy bit */
+static inline void arria10_cm_wait4fsm(void)
+{
+ register uint32_t inter_val;
+
+ do {
+ inter_val = readl(&arria10_clkmgr_base->stat) &
+ ARRIA10_CLKMGR_CLKMGR_STAT_BUSY_SET_MSK;
+ } while (inter_val);
+}
+
+static uint32_t arria10_cm_get_main_vco(void)
+{
+ uint32_t vco1, src_hz, numer, denom, vco;
+ uint32_t clk_src = readl(&arria10_clkmgr_base->main_pll_vco0);
+
+ clk_src = (clk_src >> ARRIA10_CLKMGR_MAINPLL_VCO0_PSRC_LSB) &
+ ARRIA10_CLKMGR_MAINPLL_VCO0_PSRC_MSK;
+
+ if (clk_src == ARRIA10_CLKMGR_MAINPLL_VCO0_PSRC_EOSC) {
+ src_hz = eosc1_hz;
+ } else if (clk_src == ARRIA10_CLKMGR_MAINPLL_VCO0_PSRC_E_INTOSC) {
+ src_hz = cb_intosc_hz;
+ } else if (clk_src == ARRIA10_CLKMGR_MAINPLL_VCO0_PSRC_F2S) {
+ src_hz = f2s_free_hz;
+ } else {
+ pr_err("arria10_cm_get_main_vco invalid clk_src %d\n", clk_src);
+ return 0;
+ }
+
+ vco1 = readl(&arria10_clkmgr_base->main_pll_vco1);
+ numer = vco1 & ARRIA10_CLKMGR_MAINPLL_VCO1_NUMER_MSK;
+ denom = (vco1 >> ARRIA10_CLKMGR_MAINPLL_VCO1_DENOM_LSB) &
+ ARRIA10_CLKMGR_MAINPLL_VCO1_DENOM_MSK;
+ vco = src_hz;
+ vco /= (1 + denom);
+ vco *= (1 + numer);
+
+ return vco;
+}
+
+static uint32_t arria10_cm_get_peri_vco(void)
+{
+ uint32_t vco1, src_hz, numer, denom, vco;
+ uint32_t clk_src = readl(&arria10_clkmgr_base->per_pll_vco0);
+
+ clk_src = (clk_src >> ARRIA10_CLKMGR_PERPLL_VCO0_PSRC_LSB) &
+ ARRIA10_CLKMGR_PERPLL_VCO0_PSRC_MSK;
+
+ if (clk_src == ARRIA10_CLKMGR_PERPLL_VCO0_PSRC_EOSC) {
+ src_hz = eosc1_hz;
+ } else if (clk_src == ARRIA10_CLKMGR_PERPLL_VCO0_PSRC_E_INTOSC) {
+ src_hz = cb_intosc_hz;
+ } else if (clk_src == ARRIA10_CLKMGR_PERPLL_VCO0_PSRC_F2S) {
+ src_hz = f2s_free_hz;
+ } else if (clk_src == ARRIA10_CLKMGR_PERPLL_VCO0_PSRC_MAIN) {
+ src_hz = arria10_cm_get_main_vco();
+ src_hz /= (readl(&arria10_clkmgr_base->main_pll_cntr15clk) &
+ ARRIA10_CLKMGR_MAINPLL_CNTRCLK_MSK) + 1;
+ } else {
+ pr_err("arria10_cm_get_peri_vco invalid clk_src %d\n", clk_src);
+ return 0;
+ }
+
+ vco1 = readl(&arria10_clkmgr_base->per_pll_vco1);
+ numer = vco1 & ARRIA10_CLKMGR_PERPLL_VCO1_NUMER_MSK;
+ denom = (vco1 >> ARRIA10_CLKMGR_PERPLL_VCO1_DENOM_LSB) &
+ ARRIA10_CLKMGR_PERPLL_VCO1_DENOM_MSK;
+ vco = src_hz;
+ vco /= (1 + denom);
+ vco *= (1 + numer);
+
+ return vco;
+}
+
+unsigned int arria10_cm_get_mmc_controller_clk_hz(void)
+{
+ uint32_t clk_hz = 0;
+ uint32_t clk_input = readl(&arria10_clkmgr_base->per_pll_cntr6clk);
+ clk_input = (clk_input >> ARRIA10_CLKMGR_PERPLL_CNTR6CLK_SRC_LSB) &
+ ARRIA10_CLKMGR_PERPLLGRP_SRC_MSK;
+
+ switch (clk_input) {
+ case ARRIA10_CLKMGR_PERPLLGRP_SRC_MAIN:
+ clk_hz = arria10_cm_get_main_vco();
+ clk_hz /= 1 + (readl(&arria10_clkmgr_base->main_pll_cntr6clk) &
+ ARRIA10_CLKMGR_MAINPLL_CNTRCLK_MSK);
+ break;
+
+ case ARRIA10_CLKMGR_PERPLLGRP_SRC_PERI:
+ clk_hz = arria10_cm_get_peri_vco();
+ clk_hz /= 1 + (readl(&arria10_clkmgr_base->per_pll_cntr6clk) &
+ ARRIA10_CLKMGR_PERPLL_CNTRCLK_MSK);
+ break;
+
+ case ARRIA10_CLKMGR_PERPLLGRP_SRC_OSC1:
+ clk_hz = eosc1_hz;
+ break;
+
+ case ARRIA10_CLKMGR_PERPLLGRP_SRC_INTOSC:
+ clk_hz = cb_intosc_hz;
+ break;
+
+ case ARRIA10_CLKMGR_PERPLLGRP_SRC_FPGA:
+ clk_hz = f2s_free_hz;
+ break;
+ }
+
+ return clk_hz/4;
+}
+
+/* calculate the intended main VCO frequency based on handoff */
+static uint32_t arria10_cm_calc_handoff_main_vco_clk_hz(struct arria10_mainpll_cfg *main_cfg)
+{
+ uint32_t clk_hz;
+
+ /* Check main VCO clock source: eosc, intosc or f2s? */
+ switch (main_cfg->vco0_psrc) {
+ case ARRIA10_CLKMGR_MAINPLL_VCO0_PSRC_EOSC:
+ clk_hz = eosc1_hz;
+ break;
+ case ARRIA10_CLKMGR_MAINPLL_VCO0_PSRC_E_INTOSC:
+ clk_hz = cb_intosc_hz;
+ break;
+ case ARRIA10_CLKMGR_MAINPLL_VCO0_PSRC_F2S:
+ clk_hz = f2s_free_hz;
+ break;
+ default:
+ return 0;
+ }
+
+ /* calculate the VCO frequency */
+ clk_hz /= (1 + main_cfg->vco1_denom);
+ clk_hz *= (1 + main_cfg->vco1_numer);
+
+ return clk_hz;
+}
+
+/* calculate the intended periph VCO frequency based on handoff */
+static uint32_t arria10_cm_calc_handoff_periph_vco_clk_hz(struct arria10_mainpll_cfg *main_cfg,
+ struct arria10_perpll_cfg *per_cfg)
+{
+ uint32_t clk_hz;
+
+ /* Check periph VCO clock source: eosc, intosc, f2s or mainpll? */
+ switch (per_cfg->vco0_psrc) {
+ case ARRIA10_CLKMGR_PERPLL_VCO0_PSRC_EOSC:
+ clk_hz = eosc1_hz;
+ break;
+ case ARRIA10_CLKMGR_PERPLL_VCO0_PSRC_E_INTOSC:
+ clk_hz = cb_intosc_hz;
+ break;
+ case ARRIA10_CLKMGR_PERPLL_VCO0_PSRC_F2S:
+ clk_hz = f2s_free_hz;
+ break;
+ case ARRIA10_CLKMGR_PERPLL_VCO0_PSRC_MAIN:
+ clk_hz = arria10_cm_calc_handoff_main_vco_clk_hz(main_cfg);
+ clk_hz /= main_cfg->cntr15clk_cnt;
+ break;
+ default:
+ return 0;
+ }
+
+ /* calculate the VCO frequency */
+ clk_hz /= (1 + per_cfg->vco1_denom);
+ clk_hz *= (1 + per_cfg->vco1_numer);
+
+ return clk_hz;
+}
+
+/* calculate the intended MPU clock frequency based on handoff */
+static uint32_t arria10_cm_calc_handoff_mpu_clk_hz(struct arria10_mainpll_cfg *main_cfg,
+ struct arria10_perpll_cfg *per_cfg)
+{
+ uint32_t clk_hz;
+
+ /* Check MPU clock source: main, periph, osc1, intosc or f2s? */
+ switch (main_cfg->mpuclk_src) {
+ case ARRIA10_CLKMGR_MAINPLL_MPUCLK_SRC_MAIN:
+ clk_hz = arria10_cm_calc_handoff_main_vco_clk_hz(main_cfg);
+ clk_hz /= ((main_cfg->mpuclk & ARRIA10_CLKMGR_MAINPLL_MPUCLK_CNT_MSK)
+ + 1);
+ break;
+ case ARRIA10_CLKMGR_MAINPLL_MPUCLK_SRC_PERI:
+ clk_hz = arria10_cm_calc_handoff_periph_vco_clk_hz(main_cfg, per_cfg);
+ clk_hz /= (((main_cfg->mpuclk >>
+ ARRIA10_CLKMGR_MAINPLL_MPUCLK_PERICNT_LSB) &
+ ARRIA10_CLKMGR_MAINPLL_MPUCLK_CNT_MSK) + 1);
+ break;
+ case ARRIA10_CLKMGR_MAINPLL_MPUCLK_SRC_OSC1:
+ clk_hz = eosc1_hz;
+ break;
+ case ARRIA10_CLKMGR_MAINPLL_MPUCLK_SRC_INTOSC:
+ clk_hz = cb_intosc_hz;
+ break;
+ case ARRIA10_CLKMGR_MAINPLL_MPUCLK_SRC_FPGA:
+ clk_hz = f2s_free_hz;
+ break;
+ default:
+ return 0;
+ }
+
+ clk_hz /= (main_cfg->mpuclk_cnt + 1);
+
+ return clk_hz;
+}
+
+/* calculate the intended NOC clock frequency based on handoff */
+static uint32_t arria10_cm_calc_handoff_noc_clk_hz(struct arria10_mainpll_cfg *main_cfg,
+ struct arria10_perpll_cfg *per_cfg)
+{
+ uint32_t clk_hz;
+
+ /* Check MPU clock source: main, periph, osc1, intosc or f2s? */
+ switch (main_cfg->nocclk_src) {
+ case ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_MAIN:
+ clk_hz = arria10_cm_calc_handoff_main_vco_clk_hz(main_cfg);
+ clk_hz /= ((main_cfg->nocclk & ARRIA10_CLKMGR_MAINPLL_NOCCLK_CNT_MSK)
+ + 1);
+ break;
+ case ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_PERI:
+ clk_hz = arria10_cm_calc_handoff_periph_vco_clk_hz(main_cfg, per_cfg);
+ clk_hz /= (((main_cfg->nocclk >>
+ ARRIA10_CLKMGR_MAINPLL_NOCCLK_PERICNT_LSB) &
+ ARRIA10_CLKMGR_MAINPLL_NOCCLK_CNT_MSK) + 1);
+ break;
+ case ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_OSC1:
+ clk_hz = eosc1_hz;
+ break;
+ case ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_INTOSC:
+ clk_hz = cb_intosc_hz;
+ break;
+ case ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_FPGA:
+ clk_hz = f2s_free_hz;
+ break;
+ default:
+ return 0;
+ }
+
+ clk_hz /= (main_cfg->nocclk_cnt + 1);
+
+ return clk_hz;
+}
+
+/* return 1 if PLL ramp is required */
+static int arria10_cm_is_pll_ramp_required(int main0periph1,
+ struct arria10_mainpll_cfg *main_cfg,
+ struct arria10_perpll_cfg *per_cfg)
+{
+
+ /* Check for main PLL */
+ if (main0periph1 == 0) {
+ /*
+ * PLL ramp is not required if both MPU clock and NOC clock are
+ * not sourced from main PLL
+ */
+ if (main_cfg->mpuclk_src != ARRIA10_CLKMGR_MAINPLL_MPUCLK_SRC_MAIN &&
+ main_cfg->nocclk_src != ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_MAIN)
+ return 0;
+
+ /*
+ * PLL ramp is required if MPU clock is sourced from main PLL
+ * and MPU clock is over 900MHz (as advised by HW team)
+ */
+ if (main_cfg->mpuclk_src == ARRIA10_CLKMGR_MAINPLL_MPUCLK_SRC_MAIN &&
+ (arria10_cm_calc_handoff_mpu_clk_hz(main_cfg, per_cfg) >
+ ARRIA10_CLKMGR_PLL_RAMP_MPUCLK_THRESHOLD_HZ))
+ return 1;
+
+ /*
+ * PLL ramp is required if NOC clock is sourced from main PLL
+ * and NOC clock is over 300MHz (as advised by HW team)
+ */
+ if (main_cfg->nocclk_src == ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_MAIN &&
+ (arria10_cm_calc_handoff_noc_clk_hz(main_cfg, per_cfg) >
+ ARRIA10_CLKMGR_PLL_RAMP_NOCCLK_THRESHOLD_HZ))
+ return 1;
+
+ } else if (main0periph1 == 1) {
+ /*
+ * PLL ramp is not required if both MPU clock and NOC clock are
+ * not sourced from periph PLL
+ */
+ if (main_cfg->mpuclk_src != ARRIA10_CLKMGR_MAINPLL_MPUCLK_SRC_PERI &&
+ main_cfg->nocclk_src != ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_PERI)
+ return 0;
+
+ /*
+ * PLL ramp is required if MPU clock are source from periph PLL
+ * and MPU clock is over 900MHz (as advised by HW team)
+ */
+ if (main_cfg->mpuclk_src == ARRIA10_CLKMGR_MAINPLL_MPUCLK_SRC_PERI &&
+ (arria10_cm_calc_handoff_mpu_clk_hz(main_cfg, per_cfg) >
+ ARRIA10_CLKMGR_PLL_RAMP_MPUCLK_THRESHOLD_HZ))
+ return 1;
+
+ /*
+ * PLL ramp is required if NOC clock are source from periph PLL
+ * and NOC clock is over 300MHz (as advised by HW team)
+ */
+ if (main_cfg->nocclk_src == ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_PERI &&
+ (arria10_cm_calc_handoff_noc_clk_hz(main_cfg, per_cfg) >
+ ARRIA10_CLKMGR_PLL_RAMP_NOCCLK_THRESHOLD_HZ))
+ return 1;
+ }
+
+ return 0;
+}
+
+/*
+ * Calculate the new PLL numerator which is based on existing DTS hand off and
+ * intended safe frequency (safe_hz). Note that PLL ramp is only modifying the
+ * numerator while maintaining denominator as denominator will influence the
+ * jitter condition. Please refer A10 HPS TRM for the jitter guide. Note final
+ * value for numerator is minus with 1 to cater our register value
+ * representation.
+ */
+static uint32_t arria10_cm_calc_safe_pll_numer(int main0periph1,
+ struct arria10_mainpll_cfg *main_cfg,
+ struct arria10_perpll_cfg *per_cfg,
+ uint32_t safe_hz)
+{
+ uint32_t clk_hz = 0;
+
+ /* Check for main PLL */
+ if (main0periph1 == 0) {
+ /* Check main VCO clock source: eosc, intosc or f2s? */
+ switch (main_cfg->vco0_psrc) {
+ case ARRIA10_CLKMGR_MAINPLL_VCO0_PSRC_EOSC:
+ clk_hz = eosc1_hz;
+ break;
+ case ARRIA10_CLKMGR_MAINPLL_VCO0_PSRC_E_INTOSC:
+ clk_hz = cb_intosc_hz;
+ break;
+ case ARRIA10_CLKMGR_MAINPLL_VCO0_PSRC_F2S:
+ clk_hz = f2s_free_hz;
+ break;
+ default:
+ return 0;
+ }
+
+ /* Applicable if MPU clock is from main PLL */
+ if (main_cfg->mpuclk_src == ARRIA10_CLKMGR_MAINPLL_MPUCLK_SRC_MAIN) {
+ /* calculate the safe numer value */
+ clk_hz = (safe_hz / clk_hz) *
+ (main_cfg->mpuclk_cnt + 1) *
+ ((main_cfg->mpuclk &
+ ARRIA10_CLKMGR_MAINPLL_MPUCLK_CNT_MSK) + 1) *
+ (1 + main_cfg->vco1_denom) - 1;
+ }
+ /* Reach here if MPU clk not from main PLL but NOC clk is */
+ else if (main_cfg->nocclk_src ==
+ ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_MAIN) {
+ /* calculate the safe numer value */
+ clk_hz = (safe_hz / clk_hz) *
+ (main_cfg->nocclk_cnt + 1) *
+ ((main_cfg->nocclk &
+ ARRIA10_CLKMGR_MAINPLL_NOCCLK_CNT_MSK) + 1) *
+ (1 + main_cfg->vco1_denom) - 1;
+ } else {
+ clk_hz = 0;
+ }
+
+ } else if (main0periph1 == 1) {
+ /* Check periph VCO clock source: eosc, intosc, f2s, mainpll */
+ switch (per_cfg->vco0_psrc) {
+ case ARRIA10_CLKMGR_PERPLL_VCO0_PSRC_EOSC:
+ clk_hz = eosc1_hz;
+ break;
+ case ARRIA10_CLKMGR_PERPLL_VCO0_PSRC_E_INTOSC:
+ clk_hz = cb_intosc_hz;
+ break;
+ case ARRIA10_CLKMGR_PERPLL_VCO0_PSRC_F2S:
+ clk_hz = f2s_free_hz;
+ break;
+ case ARRIA10_CLKMGR_PERPLL_VCO0_PSRC_MAIN:
+ clk_hz = arria10_cm_calc_handoff_main_vco_clk_hz(
+ main_cfg);
+ clk_hz /= main_cfg->cntr15clk_cnt;
+ break;
+ default:
+ return 0;
+ }
+ /* Applicable if MPU clock is from periph PLL */
+ if (main_cfg->mpuclk_src == ARRIA10_CLKMGR_MAINPLL_MPUCLK_SRC_PERI) {
+ /* calculate the safe numer value */
+ clk_hz = (safe_hz / clk_hz) *
+ (main_cfg->mpuclk_cnt + 1) *
+ (((main_cfg->mpuclk >>
+ ARRIA10_CLKMGR_MAINPLL_MPUCLK_PERICNT_LSB) &
+ ARRIA10_CLKMGR_MAINPLL_MPUCLK_CNT_MSK) + 1) *
+ (1 + per_cfg->vco1_denom) - 1;
+ }
+ /* Reach here if MPU clk not from periph PLL but NOC clk is */
+ else if (main_cfg->nocclk_src ==
+ ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_PERI) {
+ /* calculate the safe numer value */
+ clk_hz = (safe_hz / clk_hz) *
+ (main_cfg->nocclk_cnt + 1) *
+ (((main_cfg->nocclk >>
+ ARRIA10_CLKMGR_MAINPLL_NOCCLK_PERICNT_LSB) &
+ ARRIA10_CLKMGR_MAINPLL_NOCCLK_CNT_MSK) + 1) *
+ (1 + per_cfg->vco1_denom) - 1;
+ } else {
+ clk_hz = 0;
+ }
+ }
+
+ return clk_hz;
+}
+
+/* ramping the main PLL to final value */
+static void arria10_cm_pll_ramp_main(struct arria10_mainpll_cfg *main_cfg,
+ struct arria10_perpll_cfg *per_cfg,
+ uint32_t pll_ramp_main_hz)
+{
+ uint32_t clk_hz = 0;
+ uint32_t clk_incr_hz = 0;
+ uint32_t clk_final_hz = 0;
+
+ /* find out the increment value */
+ if (main_cfg->mpuclk_src == ARRIA10_CLKMGR_MAINPLL_MPUCLK_SRC_MAIN) {
+ clk_incr_hz = ARRIA10_CLKMGR_PLL_RAMP_MPUCLK_INCREMENT_HZ;
+ clk_final_hz = arria10_cm_calc_handoff_mpu_clk_hz(main_cfg, per_cfg);
+ } else if (main_cfg->nocclk_src == ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_MAIN) {
+ clk_incr_hz = ARRIA10_CLKMGR_PLL_RAMP_NOCCLK_INCREMENT_HZ;
+ clk_final_hz = arria10_cm_calc_handoff_noc_clk_hz(main_cfg, per_cfg);
+ }
+
+ /* execute the ramping here */
+ for (clk_hz = pll_ramp_main_hz + clk_incr_hz;
+ clk_hz < clk_final_hz; clk_hz += clk_incr_hz) {
+ writel((main_cfg->vco1_denom << ARRIA10_CLKMGR_MAINPLL_VCO1_DENOM_LSB) |
+ arria10_cm_calc_safe_pll_numer(0, main_cfg, per_cfg, clk_hz),
+ &arria10_clkmgr_base->main_pll_vco1);
+ udelay(1000);
+ arria10_cm_wait_for_lock(LOCKED_MASK);
+ }
+
+ writel((main_cfg->vco1_denom << ARRIA10_CLKMGR_MAINPLL_VCO1_DENOM_LSB) |
+ main_cfg->vco1_numer, &arria10_clkmgr_base->main_pll_vco1);
+
+ udelay(1000);
+ arria10_cm_wait_for_lock(LOCKED_MASK);
+}
+
+/* ramping the periph PLL to final value */
+static void arria10_cm_pll_ramp_periph(struct arria10_mainpll_cfg *main_cfg,
+ struct arria10_perpll_cfg *per_cfg,
+ uint32_t pll_ramp_periph_hz)
+{
+ uint32_t clk_hz = 0;
+ uint32_t clk_incr_hz = 0;
+ uint32_t clk_final_hz = 0;
+
+ /* find out the increment value */
+ if (main_cfg->mpuclk_src == ARRIA10_CLKMGR_MAINPLL_MPUCLK_SRC_PERI) {
+ clk_incr_hz = ARRIA10_CLKMGR_PLL_RAMP_MPUCLK_INCREMENT_HZ;
+ clk_final_hz = arria10_cm_calc_handoff_mpu_clk_hz(main_cfg, per_cfg);
+ } else if (main_cfg->nocclk_src == ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_PERI) {
+ clk_incr_hz = ARRIA10_CLKMGR_PLL_RAMP_NOCCLK_INCREMENT_HZ;
+ clk_final_hz = arria10_cm_calc_handoff_noc_clk_hz(main_cfg, per_cfg);
+ }
+
+ /* execute the ramping here */
+ for (clk_hz = pll_ramp_periph_hz + clk_incr_hz;
+ clk_hz < clk_final_hz; clk_hz += clk_incr_hz) {
+ writel((per_cfg->vco1_denom << ARRIA10_CLKMGR_PERPLL_VCO1_DENOM_LSB) |
+ arria10_cm_calc_safe_pll_numer(1, main_cfg, per_cfg, clk_hz),
+ &arria10_clkmgr_base->per_pll_vco1);
+ udelay(1000);
+ arria10_cm_wait_for_lock(LOCKED_MASK);
+ }
+
+ writel((per_cfg->vco1_denom << ARRIA10_CLKMGR_PERPLL_VCO1_DENOM_LSB) |
+ per_cfg->vco1_numer, &arria10_clkmgr_base->per_pll_vco1);
+ udelay(1000);
+ arria10_cm_wait_for_lock(LOCKED_MASK);
+}
+
+/*
+ * Setup clocks while making no assumptions of the
+ * previous state of the clocks.
+ *
+ * - Start by being paranoid and gate all sw managed clocks
+ * - Put all plls in bypass
+ * - Put all plls VCO registers back to reset value (bgpwr dwn).
+ * - Put peripheral and main pll src to reset value to avoid glitch.
+ * - Delay 5 us.
+ * - Deassert bg pwr dn and set numerator and denominator
+ * - Start 7 us timer.
+ * - set internal dividers
+ * - Wait for 7 us timer.
+ * - Enable plls
+ * - Set external dividers while plls are locking
+ * - Wait for pll lock
+ * - Assert/deassert outreset all.
+ * - Take all pll's out of bypass
+ * - Clear safe mode
+ * - set source main and peripheral clocks
+ * - Ungate clocks
+ */
+static int arria10_cm_full_cfg(struct arria10_mainpll_cfg *main_cfg,
+ struct arria10_perpll_cfg *per_cfg)
+{
+ uint32_t pll_ramp_main_hz = 0;
+ uint32_t pll_ramp_periph_hz = 0;
+
+ /* gate off all mainpll clock excpet HW managed clock */
+ writel(ARRIA10_CLKMGR_MAINPLL_EN_S2FUSER0CLKEN_SET_MSK |
+ ARRIA10_CLKMGR_MAINPLL_EN_HMCPLLREFCLKEN_SET_MSK,
+ &arria10_clkmgr_base->main_pll_enr);
+
+ /* now we can gate off the rest of the peripheral clocks */
+ writel(0, &arria10_clkmgr_base->per_pll_en);
+
+ /* Put all plls in external bypass */
+ writel(ARRIA10_CLKMGR_MAINPLL_BYPASS_RESET,
+ &arria10_clkmgr_base->main_pll_bypasss);
+ writel(ARRIA10_CLKMGR_PERPLL_BYPASS_RESET,
+ &arria10_clkmgr_base->per_pll_bypasss);
+
+ /*
+ * Put all plls VCO registers back to reset value.
+ * Some code might have messed with them. At same time set the
+ * desired clock source
+ */
+ writel(ARRIA10_CLKMGR_MAINPLL_VCO0_RESET |
+ ARRIA10_CLKMGR_MAINPLL_VCO0_REGEXTSEL_SET_MSK |
+ (main_cfg->vco0_psrc << ARRIA10_CLKMGR_MAINPLL_VCO0_PSRC_LSB),
+ &arria10_clkmgr_base->main_pll_vco0);
+
+ writel(ARRIA10_CLKMGR_PERPLL_VCO0_RESET |
+ ARRIA10_CLKMGR_PERPLL_VCO0_REGEXTSEL_SET_MSK |
+ (per_cfg->vco0_psrc << ARRIA10_CLKMGR_PERPLL_VCO0_PSRC_LSB),
+ &arria10_clkmgr_base->per_pll_vco0);
+
+ writel(ARRIA10_CLKMGR_MAINPLL_VCO1_RESET,
+ &arria10_clkmgr_base->main_pll_vco1);
+ writel(ARRIA10_CLKMGR_PERPLL_VCO1_RESET,
+ &arria10_clkmgr_base->per_pll_vco1);
+
+ /* clear the interrupt register status register */
+ writel(ARRIA10_CLKMGR_CLKMGR_INTR_MAINPLLLOST_SET_MSK |
+ ARRIA10_CLKMGR_CLKMGR_INTR_PERPLLLOST_SET_MSK |
+ ARRIA10_CLKMGR_CLKMGR_INTR_MAINPLLRFSLIP_SET_MSK |
+ ARRIA10_CLKMGR_CLKMGR_INTR_PERPLLRFSLIP_SET_MSK |
+ ARRIA10_CLKMGR_CLKMGR_INTR_MAINPLLFBSLIP_SET_MSK |
+ ARRIA10_CLKMGR_CLKMGR_INTR_PERPLLFBSLIP_SET_MSK |
+ ARRIA10_CLKMGR_CLKMGR_INTR_MAINPLLACHIEVED_SET_MSK |
+ ARRIA10_CLKMGR_CLKMGR_INTR_PERPLLACHIEVED_SET_MSK,
+ &arria10_clkmgr_base->intr);
+
+ /* Program VCO “Numerator” and “Denominator” for main PLL */
+ if (arria10_cm_is_pll_ramp_required(0, main_cfg, per_cfg)) {
+ /* set main PLL to safe starting threshold frequency */
+ if (main_cfg->mpuclk_src == ARRIA10_CLKMGR_MAINPLL_MPUCLK_SRC_MAIN)
+ pll_ramp_main_hz = ARRIA10_CLKMGR_PLL_RAMP_MPUCLK_THRESHOLD_HZ;
+ else if (main_cfg->nocclk_src == ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_MAIN)
+ pll_ramp_main_hz = ARRIA10_CLKMGR_PLL_RAMP_NOCCLK_THRESHOLD_HZ;
+
+ writel((main_cfg->vco1_denom << ARRIA10_CLKMGR_MAINPLL_VCO1_DENOM_LSB) |
+ arria10_cm_calc_safe_pll_numer(0, main_cfg, per_cfg,
+ pll_ramp_main_hz),
+ &arria10_clkmgr_base->main_pll_vco1);
+ } else {
+ writel((main_cfg->vco1_denom << ARRIA10_CLKMGR_MAINPLL_VCO1_DENOM_LSB) |
+ main_cfg->vco1_numer,
+ &arria10_clkmgr_base->main_pll_vco1);
+ }
+
+ /* Program VCO “Numerator” and “Denominator” for periph PLL */
+ if (arria10_cm_is_pll_ramp_required(1, main_cfg, per_cfg)) {
+ /* set periph PLL to safe starting threshold frequency */
+ if (main_cfg->mpuclk_src == ARRIA10_CLKMGR_MAINPLL_MPUCLK_SRC_PERI)
+ pll_ramp_periph_hz = ARRIA10_CLKMGR_PLL_RAMP_MPUCLK_THRESHOLD_HZ;
+ else if (main_cfg->nocclk_src == ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_PERI)
+ pll_ramp_periph_hz = ARRIA10_CLKMGR_PLL_RAMP_NOCCLK_THRESHOLD_HZ;
+
+ writel((per_cfg->vco1_denom << ARRIA10_CLKMGR_PERPLL_VCO1_DENOM_LSB) |
+ arria10_cm_calc_safe_pll_numer(1, main_cfg, per_cfg,
+ pll_ramp_periph_hz),
+ &arria10_clkmgr_base->per_pll_vco1);
+ } else {
+ writel((per_cfg->vco1_denom << ARRIA10_CLKMGR_PERPLL_VCO1_DENOM_LSB) |
+ per_cfg->vco1_numer, &arria10_clkmgr_base->per_pll_vco1);
+ }
+
+ /* Wait for at least 5 us */
+ udelay(5);
+
+ /* Now deassert BGPWRDN and PWRDN */
+ clrbits_le32(&arria10_clkmgr_base->main_pll_vco0,
+ ARRIA10_CLKMGR_MAINPLL_VCO0_BGPWRDN_SET_MSK |
+ ARRIA10_CLKMGR_MAINPLL_VCO0_PWRDN_SET_MSK);
+ clrbits_le32(&arria10_clkmgr_base->per_pll_vco0,
+ ARRIA10_CLKMGR_PERPLL_VCO0_BGPWRDN_SET_MSK |
+ ARRIA10_CLKMGR_PERPLL_VCO0_PWRDN_SET_MSK);
+
+ /* Wait for at least 7 us */
+ udelay(7);
+
+ /* enable the VCO and disable the external regulator to PLL */
+ writel((readl(&arria10_clkmgr_base->main_pll_vco0) &
+ ~ARRIA10_CLKMGR_MAINPLL_VCO0_REGEXTSEL_SET_MSK) |
+ ARRIA10_CLKMGR_MAINPLL_VCO0_EN_SET_MSK,
+ &arria10_clkmgr_base->main_pll_vco0);
+ writel((readl(&arria10_clkmgr_base->per_pll_vco0) &
+ ~ARRIA10_CLKMGR_PERPLL_VCO0_REGEXTSEL_SET_MSK) |
+ ARRIA10_CLKMGR_PERPLL_VCO0_EN_SET_MSK,
+ &arria10_clkmgr_base->per_pll_vco0);
+
+ /* setup all the main PLL counter and clock source */
+ writel(main_cfg->nocclk,
+ ARRIA10_CLKMGR_ADDR + ARRIA10_CLKMGR_MAINPLL_NOC_CLK_OFFSET);
+ writel(main_cfg->mpuclk,
+ ARRIA10_CLKMGR_ADDR + ARRIA10_CLKMGR_ALTERAGRP_MPU_CLK_OFFSET);
+
+ /* main_emaca_clk divider */
+ writel(main_cfg->cntr2clk_cnt, &arria10_clkmgr_base->main_pll_cntr2clk);
+ /* main_emacb_clk divider */
+ writel(main_cfg->cntr3clk_cnt, &arria10_clkmgr_base->main_pll_cntr3clk);
+ /* main_emac_ptp_clk divider */
+ writel(main_cfg->cntr4clk_cnt, &arria10_clkmgr_base->main_pll_cntr4clk);
+ /* main_gpio_db_clk divider */
+ writel(main_cfg->cntr5clk_cnt, &arria10_clkmgr_base->main_pll_cntr5clk);
+ /* main_sdmmc_clk divider */
+ writel(main_cfg->cntr6clk_cnt, &arria10_clkmgr_base->main_pll_cntr6clk);
+ /* main_s2f_user0_clk divider */
+ writel(main_cfg->cntr7clk_cnt |
+ (main_cfg->cntr7clk_src << ARRIA10_CLKMGR_MAINPLL_CNTR7CLK_SRC_LSB),
+ &arria10_clkmgr_base->main_pll_cntr7clk);
+ /* main_s2f_user1_clk divider */
+ writel(main_cfg->cntr8clk_cnt, &arria10_clkmgr_base->main_pll_cntr8clk);
+ /* main_hmc_pll_clk divider */
+ writel(main_cfg->cntr9clk_cnt |
+ (main_cfg->cntr9clk_src << ARRIA10_CLKMGR_MAINPLL_CNTR9CLK_SRC_LSB),
+ &arria10_clkmgr_base->main_pll_cntr9clk);
+ /* main_periph_ref_clk divider */
+ writel(main_cfg->cntr15clk_cnt, &arria10_clkmgr_base->main_pll_cntr15clk);
+
+ /* setup all the peripheral PLL counter and clock source */
+ /* peri_emaca_clk divider */
+ writel(per_cfg->cntr2clk_cnt |
+ (per_cfg->cntr2clk_src << ARRIA10_CLKMGR_PERPLL_CNTR2CLK_SRC_LSB),
+ &arria10_clkmgr_base->per_pll_cntr2clk);
+ /* peri_emacb_clk divider */
+ writel(per_cfg->cntr3clk_cnt |
+ (per_cfg->cntr3clk_src << ARRIA10_CLKMGR_PERPLL_CNTR3CLK_SRC_LSB),
+ &arria10_clkmgr_base->per_pll_cntr3clk);
+ /* peri_emac_ptp_clk divider */
+ writel(per_cfg->cntr4clk_cnt |
+ (per_cfg->cntr4clk_src << ARRIA10_CLKMGR_PERPLL_CNTR4CLK_SRC_LSB),
+ &arria10_clkmgr_base->per_pll_cntr4clk);
+ /* peri_gpio_db_clk divider */
+ writel(per_cfg->cntr5clk_cnt |
+ (per_cfg->cntr5clk_src << ARRIA10_CLKMGR_PERPLL_CNTR5CLK_SRC_LSB),
+ &arria10_clkmgr_base->per_pll_cntr5clk);
+ /* peri_sdmmc_clk divider */
+ writel(per_cfg->cntr6clk_cnt |
+ (per_cfg->cntr6clk_src << ARRIA10_CLKMGR_PERPLL_CNTR6CLK_SRC_LSB),
+ &arria10_clkmgr_base->per_pll_cntr6clk);
+ /* peri_s2f_user0_clk divider */
+ writel(per_cfg->cntr7clk_cnt, &arria10_clkmgr_base->per_pll_cntr7clk);
+ /* peri_s2f_user1_clk divider */
+ writel(per_cfg->cntr8clk_cnt |
+ (per_cfg->cntr8clk_src << ARRIA10_CLKMGR_PERPLL_CNTR8CLK_SRC_LSB),
+ &arria10_clkmgr_base->per_pll_cntr8clk);
+ /* peri_hmc_pll_clk divider */
+ writel(per_cfg->cntr9clk_cnt, &arria10_clkmgr_base->per_pll_cntr9clk);
+
+ /* setup all the external PLL counter */
+ /* mpu wrapper / external divider */
+ writel(main_cfg->mpuclk_cnt |
+ (main_cfg->mpuclk_src << ARRIA10_CLKMGR_MAINPLL_MPUCLK_SRC_LSB),
+ &arria10_clkmgr_base->main_pll_mpuclk);
+ /* NOC wrapper / external divider */
+ writel(main_cfg->nocclk_cnt |
+ (main_cfg->nocclk_src << ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_LSB),
+ &arria10_clkmgr_base->main_pll_nocclk);
+ /* NOC subclock divider such as l4 */
+ writel(main_cfg->nocdiv_l4mainclk |
+ (main_cfg->nocdiv_l4mpclk << ARRIA10_CLKMGR_MAINPLL_NOCDIV_L4MPCLK_LSB) |
+ (main_cfg->nocdiv_l4spclk << ARRIA10_CLKMGR_MAINPLL_NOCDIV_L4SPCLK_LSB) |
+ (main_cfg->nocdiv_csatclk << ARRIA10_CLKMGR_MAINPLL_NOCDIV_CSATCLK_LSB) |
+ (main_cfg->nocdiv_cstraceclk << ARRIA10_CLKMGR_MAINPLL_NOCDIV_CSTRACECLK_LSB) |
+ (main_cfg->nocdiv_cspdbgclk << ARRIA10_CLKMGR_MAINPLL_NOCDIV_CSPDBGCLK_LSB),
+ &arria10_clkmgr_base->main_pll_nocdiv);
+ /* gpio_db external divider */
+ writel(per_cfg->gpiodiv_gpiodbclk, &arria10_clkmgr_base->per_pll_gpiodiv);
+
+ /* setup the EMAC clock mux select */
+ writel((per_cfg->emacctl_emac0sel < ARRIA10_CLKMGR_PERPLL_EMACCTL_EMAC0SEL_LSB) |
+ (per_cfg->emacctl_emac1sel << ARRIA10_CLKMGR_PERPLL_EMACCTL_EMAC1SEL_LSB) |
+ (per_cfg->emacctl_emac2sel << ARRIA10_CLKMGR_PERPLL_EMACCTL_EMAC2SEL_LSB),
+ &arria10_clkmgr_base->per_pll_emacctl);
+
+ /* at this stage, check for PLL lock status */
+ arria10_cm_wait_for_lock(LOCKED_MASK);
+
+ /*
+ * after locking, but before taking out of bypass,
+ * assert/deassert outresetall
+ */
+
+ /* assert mainpll outresetall */
+ setbits_le32(&arria10_clkmgr_base->main_pll_vco0,
+ ARRIA10_CLKMGR_MAINPLL_VCO0_OUTRSTALL_SET_MSK);
+ /* assert perpll outresetall */
+ setbits_le32(&arria10_clkmgr_base->per_pll_vco0,
+ ARRIA10_CLKMGR_PERPLL_VCO0_OUTRSTALL_SET_MSK);
+ /* de-assert mainpll outresetall */
+ clrbits_le32(&arria10_clkmgr_base->main_pll_vco0,
+ ARRIA10_CLKMGR_MAINPLL_VCO0_OUTRSTALL_SET_MSK);
+ /* de-assert perpll outresetall */
+ clrbits_le32(&arria10_clkmgr_base->per_pll_vco0,
+ ARRIA10_CLKMGR_PERPLL_VCO0_OUTRSTALL_SET_MSK);
+
+ /*
+ * Take all PLLs out of bypass when boot mode is cleared.
+ * release mainpll from bypass
+ */
+ writel(ARRIA10_CLKMGR_MAINPLL_BYPASS_RESET,
+ &arria10_clkmgr_base->main_pll_bypassr);
+ /* wait till Clock Manager is not busy */
+ arria10_cm_wait4fsm();
+
+ /* release perpll from bypass */
+ writel(ARRIA10_CLKMGR_PERPLL_BYPASS_RESET,
+ &arria10_clkmgr_base->per_pll_bypassr);
+ /* wait till Clock Manager is not busy */
+ arria10_cm_wait4fsm();
+
+ /* clear boot mode */
+ clrbits_le32(&arria10_clkmgr_base->ctrl,
+ ARRIA10_CLKMGR_CLKMGR_CTL_BOOTMOD_SET_MSK);
+ /* wait till Clock Manager is not busy */
+ arria10_cm_wait4fsm();
+
+ /* At here, we need to ramp to final value if needed */
+ if (pll_ramp_main_hz != 0)
+ arria10_cm_pll_ramp_main(main_cfg, per_cfg, pll_ramp_main_hz);
+ if (pll_ramp_periph_hz != 0)
+ arria10_cm_pll_ramp_periph(main_cfg, per_cfg, pll_ramp_periph_hz);
+
+ /* Now ungate non-hw-managed clocks */
+ writel(ARRIA10_CLKMGR_MAINPLL_EN_S2FUSER0CLKEN_SET_MSK |
+ ARRIA10_CLKMGR_MAINPLL_EN_HMCPLLREFCLKEN_SET_MSK,
+ &arria10_clkmgr_base->main_pll_ens);
+ writel(ARRIA10_CLKMGR_PERPLL_EN_RESET,
+ &arria10_clkmgr_base->per_pll_ens);
+
+ /*
+ * Clear the loss lock and slip bits as they might set during
+ * clock reconfiguration
+ */
+ writel(ARRIA10_CLKMGR_CLKMGR_INTR_MAINPLLLOST_SET_MSK |
+ ARRIA10_CLKMGR_CLKMGR_INTR_PERPLLLOST_SET_MSK |
+ ARRIA10_CLKMGR_CLKMGR_INTR_MAINPLLRFSLIP_SET_MSK |
+ ARRIA10_CLKMGR_CLKMGR_INTR_PERPLLRFSLIP_SET_MSK |
+ ARRIA10_CLKMGR_CLKMGR_INTR_MAINPLLFBSLIP_SET_MSK |
+ ARRIA10_CLKMGR_CLKMGR_INTR_PERPLLFBSLIP_SET_MSK,
+ &arria10_clkmgr_base->intr);
+
+ return 0;
+}
+
+int arria10_cm_basic_init(struct arria10_mainpll_cfg *mainpll,
+ struct arria10_perpll_cfg *perpll)
+{
+ return arria10_cm_full_cfg(mainpll, perpll);
+}
+
+void arria10_cm_use_intosc(void)
+{
+ setbits_le32(&arria10_clkmgr_base->ctrl,
+ ARRIA10_CLKMGR_CLKMGR_CTL_BOOTCLK_INTOSC_SET_MSK);
+}
diff --git a/arch/arm/mach-socfpga/arria10-generic.c b/arch/arm/mach-socfpga/arria10-generic.c
new file mode 100644
index 000000000000..b8129eaf23ff
--- /dev/null
+++ b/arch/arm/mach-socfpga/arria10-generic.c
@@ -0,0 +1,85 @@
+#include <common.h>
+#include <io.h>
+#include <init.h>
+#include <restart.h>
+#include <mach/generic.h>
+#include <mach/arria10-reset-manager.h>
+#include <mach/arria10-system-manager.h>
+#include <mach/arria10-regs.h>
+
+/* Some initialization for the EMAC */
+static void arria10_init_emac(void)
+{
+ uint32_t rst, val;
+
+ /* No need for this without network support, e.g. xloader build */
+ if (!IS_ENABLED(CONFIG_NET))
+ return;
+
+ rst = readl(ARRIA10_RSTMGR_ADDR + ARRIA10_RSTMGR_PER0MODRST);
+ rst |= ARRIA10_RSTMGR_PER0MODRST_EMAC0 |
+ ARRIA10_RSTMGR_PER0MODRST_EMAC1 |
+ ARRIA10_RSTMGR_PER0MODRST_EMAC2;
+
+ writel(rst, ARRIA10_RSTMGR_ADDR + ARRIA10_RSTMGR_PER0MODRST);
+ val = readl(ARRIA10_SYSMGR_EMAC0);
+ val &= ~(ARRIA10_SYSMGR_EMACGRP_CTRL_PHYSEL_MASK);
+ val |= ARRIA10_SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_RGMII;
+ writel(val, ARRIA10_SYSMGR_EMAC0);
+
+ val = readl(ARRIA10_SYSMGR_EMAC1);
+ val &= ~(ARRIA10_SYSMGR_EMACGRP_CTRL_PHYSEL_MASK);
+ val |= ARRIA10_SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_RGMII;
+ writel(val, ARRIA10_SYSMGR_EMAC1);
+
+ val = readl(ARRIA10_SYSMGR_EMAC2);
+ val &= ~(ARRIA10_SYSMGR_EMACGRP_CTRL_PHYSEL_MASK);
+ val |= ARRIA10_SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_RGMII;
+ writel(val, ARRIA10_SYSMGR_EMAC2);
+
+ val = readl(ARRIA10_SYSMGR_FPGAINTF_EN_3);
+ val &= ~(ARRIA10_SYSMGR_FPGAINTF_EN3_EMAC0 |
+ ARRIA10_SYSMGR_FPGAINTF_EN3_EMAC0_SW |
+ ARRIA10_SYSMGR_FPGAINTF_EN3_EMAC1 |
+ ARRIA10_SYSMGR_FPGAINTF_EN3_EMAC1_SW |
+ ARRIA10_SYSMGR_FPGAINTF_EN3_EMAC2 |
+ ARRIA10_SYSMGR_FPGAINTF_EN3_EMAC2_SW);
+
+ rst = readl(ARRIA10_RSTMGR_ADDR + ARRIA10_RSTMGR_PER0MODRST);
+ rst &= ~(ARRIA10_RSTMGR_PER0MODRST_EMAC0 |
+ ARRIA10_RSTMGR_PER0MODRST_EMAC1 |
+ ARRIA10_RSTMGR_PER0MODRST_EMAC2);
+ writel(rst, ARRIA10_RSTMGR_ADDR + ARRIA10_RSTMGR_PER0MODRST);
+}
+
+/* Write the reset manager register to cause reset */
+static void __noreturn arria10_restart_soc(struct restart_handler *rst)
+{
+ /* request a warm reset */
+ writel(ARRIA10_RSTMGR_CTL_SWWARMRSTREQ,
+ ARRIA10_RSTMGR_ADDR + ARRIA10_RSTMGR_CTRL);
+ /*
+ * infinite loop here as watchdog will trigger and reset
+ * the processor
+ */
+ hang();
+}
+
+static int arria10_generic_init(void)
+{
+ barebox_set_model("SoCFPGA Arria10");
+
+ pr_debug("Setting SDMMC phase shifts for Arria10\n");
+ writel(ARRIA10_SYSMGR_SDMMC_DRVSEL(3) |
+ ARRIA10_SYSMGR_SDMMC_SMPLSEL(0),
+ ARRIA10_SYSMGR_SDMMC);
+
+ pr_debug("Initialize EMACs\n");
+ arria10_init_emac();
+
+ pr_debug("Register restart handler\n");
+ restart_handler_register_fn(arria10_restart_soc);
+
+ return 0;
+}
+postcore_initcall(arria10_generic_init);
diff --git a/arch/arm/mach-socfpga/arria10-init.c b/arch/arm/mach-socfpga/arria10-init.c
new file mode 100644
index 000000000000..9bf986f398e9
--- /dev/null
+++ b/arch/arm/mach-socfpga/arria10-init.c
@@ -0,0 +1,275 @@
+/*
+ * Copyright (C) 2014 Altera Corporation <www.altera.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+#include <common.h>
+#include <debug_ll.h>
+#include <mach/arria10-regs.h>
+#include <mach/arria10-clock-manager.h>
+#include <mach/arria10-pinmux.h>
+#include <mach/arria10-reset-manager.h>
+#include <mach/arria10-system-manager.h>
+#include <mach/generic.h>
+#include <asm/io.h>
+#include <asm/cache-l2x0.h>
+#include <asm/system.h>
+
+#define L310_AUX_CTRL_EARLY_BRESP BIT(30) /* R2P0+ */
+#define L310_AUX_CTRL_NS_LOCKDOWN BIT(26)
+#define L310_AUX_CTRL_FULL_LINE_ZERO BIT(0) /* R2P0+ */
+
+static inline void set_auxcr(unsigned int val)
+{
+ asm volatile("mcr p15, 0, %0, c1, c0, 1 @ set AUXCR"
+ : : "r" (val));
+ isb();
+}
+
+static inline unsigned int get_auxcr(void)
+{
+ unsigned int val;
+
+ asm("mrc p15, 0, %0, c1, c0, 1 @ get AUXCR" : "=r" (val));
+ return val;
+}
+
+static void l2c310_disable(void __iomem *base)
+{
+ u32 aux;
+ int ways = 8;
+
+ aux = readl(base + L2X0_AUX_CTRL);
+
+ /*
+ * If full-line-of-zeros is enabled, we must first disable it in the
+ * Cortex-A9 auxiliary control register before disabling the L2 cache.
+ */
+ if (aux & L310_AUX_CTRL_FULL_LINE_ZERO)
+ set_auxcr(get_auxcr() & ~(BIT(3) | BIT(2) | BIT(1)));
+
+ /* flush all ways */
+ writel((1 << ways) - 1, base + L2X0_INV_WAY);
+
+ while (readl(base + L2X0_INV_WAY) & ways)
+ ;
+
+ /* sync */
+ writel(0, base + L2X0_CACHE_SYNC);
+
+ /* disable */
+ writel(0, base + L2X0_CTRL);
+ dsb();
+}
+
+static void arria10_initialize_security_policies(void)
+{
+ void __iomem *l2x0_base = (void __iomem *) 0xfffff000;
+
+ /* BootROM leaves the L2X0 in a weird state. Always disable L2X0 for now. */
+ l2c310_disable(l2x0_base);
+
+ /* Put OCRAM in non-secure */
+ writel(0x003f0000, ARRIA10_NOC_FW_OCRAM_OCRAM_SCR_REGION0);
+ writel(0x1, ARRIA10_NOC_FW_OCRAM_OCRAM_SCR_EN);
+
+ /* Put DDR in non-secure */
+ writel(0xffff0000, ARRIA10_NOC_FW_DDR_L3_DDR_SCR_REGION0);
+ writel(0x1, ARRIA10_NOC_FW_DDR_L3_DDR_SCR_EN);
+
+ /* Enable priviledge and non priviledge access to L4 peripherals */
+ writel(0xffffffff, ARRIA10_NOC_L4_PRIV_L4_PRIV_L4_PRIV);
+
+ /* Enable secure and non secure transaction to bridges */
+ writel(0xffffffff, ARRIA10_NOC_FW_SOC2FPGA_SOC2FPGA_SCR_LWSOC2FPGA);
+ writel(0xffffffff, ARRIA10_NOC_FW_SOC2FPGA_SOC2FPGA_SCR_SOC2FPGA);
+
+ /* allow non-secure and secure transaction from/to all peripherals */
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_NAND_REG);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_NAND_DATA);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_QSPI_DATA);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_USB0_REG);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_USB1_REG);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_SPIM0);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_SPIM1);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_SPIS0);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_SPIS1);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_EMAC0);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_EMAC1);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_EMAC2);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_EMAC3);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_QSPI);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_SDMMC);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_GPIO0);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_GPIO1);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_GPIO2);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_I2C0);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_I2C1);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_I2C2);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_I2C3);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_I2C4);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_SPTIMER0);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_SPTIMER1);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_UART0);
+ writel(0xffffffff, ARRIA10_NOC_FW_L4_PER_SCR_UART1);
+
+ /* Return error instead of random data */
+ writel(0x1, ARRIA10_NOC_FW_DDR_L3_DDR_SCR_GLOBAL);
+}
+
+static void arria10_mask_ecc_errors(void)
+{
+ writel(0x0007FFFF, ARRIA10_SYSMGR_ADDR + 0x94);
+}
+
+/*
+ * First C function to initialize the critical hardware early
+ */
+void arria10_init(struct arria10_mainpll_cfg *mainpll,
+ struct arria10_perpll_cfg *perpll,
+ struct arria10_pinmux_cfg *pinmux)
+{
+ arria10_cm_use_intosc();
+
+ arria10_initialize_security_policies();
+
+ arria10_mask_ecc_errors();
+
+ /*
+ * Configure the L2 controller to make SDRAM start at 0.
+ * Set address filtering start to 0x0 (Bits [31:20]),
+ * Enable address filtering (Bit[0])
+ */
+ writel(0x00000001, ARRIA10_MPUL2_ADRFLTR_START);
+ writel(0x00000002, ARRIA10_SYSMGR_NOC_ADDR_REMAP_VALUE);
+
+ arria10_reset_peripherals();
+
+ /* timer init */
+ writel(0xffffffff, ARRIA10_OSC1TIMER0_ADDR);
+ writel(0xffffffff, ARRIA10_OSC1TIMER0_ADDR + 0x4);
+ writel(0x00000003, ARRIA10_OSC1TIMER0_ADDR + 0x8);
+
+ /* configuring the clock based on handoff */
+ arria10_cm_basic_init(mainpll, perpll);
+
+ /* dedicated pins */
+ writel(pinmux->dedicated_io_4, ARRIA10_PINMUX_DEDICATED_IO_ADDR + 0x0c);
+ writel(pinmux->dedicated_io_5, ARRIA10_PINMUX_DEDICATED_IO_ADDR + 0x10);
+ writel(pinmux->dedicated_io_6, ARRIA10_PINMUX_DEDICATED_IO_ADDR + 0x14);
+ writel(pinmux->dedicated_io_7, ARRIA10_PINMUX_DEDICATED_IO_ADDR + 0x18);
+ writel(pinmux->dedicated_io_8, ARRIA10_PINMUX_DEDICATED_IO_ADDR + 0x1c);
+ writel(pinmux->dedicated_io_9, ARRIA10_PINMUX_DEDICATED_IO_ADDR + 0x20);
+ writel(pinmux->dedicated_io_10, ARRIA10_PINMUX_DEDICATED_IO_ADDR + 0x24);
+ writel(pinmux->dedicated_io_11, ARRIA10_PINMUX_DEDICATED_IO_ADDR + 0x28);
+ writel(pinmux->dedicated_io_12, ARRIA10_PINMUX_DEDICATED_IO_ADDR + 0x2c);
+ writel(pinmux->dedicated_io_13, ARRIA10_PINMUX_DEDICATED_IO_ADDR + 0x30);
+ writel(pinmux->dedicated_io_14, ARRIA10_PINMUX_DEDICATED_IO_ADDR + 0x34);
+ writel(pinmux->dedicated_io_15, ARRIA10_PINMUX_DEDICATED_IO_ADDR + 0x38);
+ writel(pinmux->dedicated_io_16, ARRIA10_PINMUX_DEDICATED_IO_ADDR + 0x3c);
+ writel(pinmux->dedicated_io_17, ARRIA10_PINMUX_DEDICATED_IO_ADDR + 0x40);
+
+ writel(pinmux->cfg_dedicated_io_bank, ARRIA10_PINMUX_DEDICATED_IO_CFG_ADDR + 0x00);
+ writel(pinmux->cfg_dedicated_io_1, ARRIA10_PINMUX_DEDICATED_IO_CFG_ADDR + 0x04);
+ writel(pinmux->cfg_dedicated_io_2, ARRIA10_PINMUX_DEDICATED_IO_CFG_ADDR + 0x08);
+ writel(pinmux->cfg_dedicated_io_3, ARRIA10_PINMUX_DEDICATED_IO_CFG_ADDR + 0x0c);
+ writel(pinmux->cfg_dedicated_io_4, ARRIA10_PINMUX_DEDICATED_IO_CFG_ADDR + 0x10);
+ writel(pinmux->cfg_dedicated_io_5, ARRIA10_PINMUX_DEDICATED_IO_CFG_ADDR + 0x14);
+ writel(pinmux->cfg_dedicated_io_6, ARRIA10_PINMUX_DEDICATED_IO_CFG_ADDR + 0x18);
+ writel(pinmux->cfg_dedicated_io_7, ARRIA10_PINMUX_DEDICATED_IO_CFG_ADDR + 0x1c);
+ writel(pinmux->cfg_dedicated_io_8, ARRIA10_PINMUX_DEDICATED_IO_CFG_ADDR + 0x20);
+ writel(pinmux->cfg_dedicated_io_9, ARRIA10_PINMUX_DEDICATED_IO_CFG_ADDR + 0x24);
+ writel(pinmux->cfg_dedicated_io_10, ARRIA10_PINMUX_DEDICATED_IO_CFG_ADDR + 0x28);
+ writel(pinmux->cfg_dedicated_io_11, ARRIA10_PINMUX_DEDICATED_IO_CFG_ADDR + 0x2c);
+ writel(pinmux->cfg_dedicated_io_12, ARRIA10_PINMUX_DEDICATED_IO_CFG_ADDR + 0x30);
+ writel(pinmux->cfg_dedicated_io_13, ARRIA10_PINMUX_DEDICATED_IO_CFG_ADDR + 0x3c);
+ writel(pinmux->cfg_dedicated_io_14, ARRIA10_PINMUX_DEDICATED_IO_CFG_ADDR + 0x38);
+ writel(pinmux->cfg_dedicated_io_15, ARRIA10_PINMUX_DEDICATED_IO_CFG_ADDR + 0x3c);
+ writel(pinmux->cfg_dedicated_io_16, ARRIA10_PINMUX_DEDICATED_IO_CFG_ADDR + 0x40);
+ writel(pinmux->cfg_dedicated_io_17, ARRIA10_PINMUX_DEDICATED_IO_CFG_ADDR + 0x44);
+
+ /* deassert peripheral resets */
+ arria10_reset_deassert_dedicated_peripherals();
+
+ /* wait for fpga_usermode */
+ while ((readl(0xffd03080) & 0x6) == 0);
+
+ /* shared pins */
+ writel(pinmux->shared_io_q1_1, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x00);
+ writel(pinmux->shared_io_q1_2, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x04);
+ writel(pinmux->shared_io_q1_3, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x08);
+ writel(pinmux->shared_io_q1_4, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x0c);
+ writel(pinmux->shared_io_q1_5, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x10);
+ writel(pinmux->shared_io_q1_6, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x14);
+ writel(pinmux->shared_io_q1_7, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x18);
+ writel(pinmux->shared_io_q1_8, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x1c);
+ writel(pinmux->shared_io_q1_9, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x20);
+ writel(pinmux->shared_io_q1_10, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x24);
+ writel(pinmux->shared_io_q1_11, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x28);
+ writel(pinmux->shared_io_q1_12, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x2c);
+
+ writel(pinmux->shared_io_q2_1, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x30);
+ writel(pinmux->shared_io_q2_2, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x34);
+ writel(pinmux->shared_io_q2_3, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x38);
+ writel(pinmux->shared_io_q2_4, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x3c);
+ writel(pinmux->shared_io_q2_5, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x40);
+ writel(pinmux->shared_io_q2_6, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x44);
+ writel(pinmux->shared_io_q2_7, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x48);
+ writel(pinmux->shared_io_q2_8, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x4c);
+ writel(pinmux->shared_io_q2_9, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x50);
+ writel(pinmux->shared_io_q2_10, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x54);
+ writel(pinmux->shared_io_q2_11, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x58);
+ writel(pinmux->shared_io_q2_12, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x5c);
+
+ writel(pinmux->shared_io_q3_1, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x60);
+ writel(pinmux->shared_io_q3_2, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x64);
+ writel(pinmux->shared_io_q3_3, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x68);
+ writel(pinmux->shared_io_q3_4, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x6c);
+ writel(pinmux->shared_io_q3_5, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x70);
+ writel(pinmux->shared_io_q3_6, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x74);
+ writel(pinmux->shared_io_q3_7, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x78);
+ writel(pinmux->shared_io_q3_8, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x7c);
+ writel(pinmux->shared_io_q3_9, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x80);
+ writel(pinmux->shared_io_q3_10, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x84);
+ writel(pinmux->shared_io_q3_11, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x88);
+ writel(pinmux->shared_io_q3_12, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x8c);
+
+ writel(pinmux->shared_io_q4_1, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x90);
+ writel(pinmux->shared_io_q4_2, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x94);
+ writel(pinmux->shared_io_q4_3, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x98);
+ writel(pinmux->shared_io_q4_4, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0x9c);
+ writel(pinmux->shared_io_q4_5, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0xa0);
+ writel(pinmux->shared_io_q4_6, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0xa4);
+ writel(pinmux->shared_io_q4_7, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0xa8);
+ writel(pinmux->shared_io_q4_8, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0xac);
+ writel(pinmux->shared_io_q4_9, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0xb0);
+ writel(pinmux->shared_io_q4_10, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0xb4);
+ writel(pinmux->shared_io_q4_11, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0xb8);
+ writel(pinmux->shared_io_q4_12, ARRIA10_PINMUX_SHARED_3V_IO_ADDR + 0xbc);
+
+ arria10_reset_deassert_shared_peripherals();
+
+ /* usefpga: select source for signals: hps or fpga */
+ writel(pinmux->rgmii0_usefpga, ARRIA10_PINMUX_FPGA_INTERFACE_ADDR + 0x00);
+ writel(pinmux->rgmii1_usefpga, ARRIA10_PINMUX_FPGA_INTERFACE_ADDR + 0x04);
+ writel(pinmux->rgmii2_usefpga, ARRIA10_PINMUX_FPGA_INTERFACE_ADDR + 0x08);
+ writel(pinmux->i2c0_usefpga, ARRIA10_PINMUX_FPGA_INTERFACE_ADDR + 0x0c);
+ writel(pinmux->i2c1_usefpga, ARRIA10_PINMUX_FPGA_INTERFACE_ADDR + 0x10);
+ writel(pinmux->i2cemac0_usefpga, ARRIA10_PINMUX_FPGA_INTERFACE_ADDR + 0x14);
+ writel(pinmux->i2cemac1_usefpga, ARRIA10_PINMUX_FPGA_INTERFACE_ADDR + 0x18);
+ writel(pinmux->i2cemac2_usefpga, ARRIA10_PINMUX_FPGA_INTERFACE_ADDR + 0x1c);
+ writel(pinmux->nand_usefpga, ARRIA10_PINMUX_FPGA_INTERFACE_ADDR + 0x20);
+ writel(pinmux->qspi_usefpga, ARRIA10_PINMUX_FPGA_INTERFACE_ADDR + 0x24);
+ writel(pinmux->sdmmc_usefpga, ARRIA10_PINMUX_FPGA_INTERFACE_ADDR + 0x28);
+ writel(pinmux->spim0_usefpga, ARRIA10_PINMUX_FPGA_INTERFACE_ADDR + 0x2c);
+ writel(pinmux->spim1_usefpga, ARRIA10_PINMUX_FPGA_INTERFACE_ADDR + 0x30);
+ writel(pinmux->spis0_usefpga, ARRIA10_PINMUX_FPGA_INTERFACE_ADDR + 0x34);
+ writel(pinmux->spis1_usefpga, ARRIA10_PINMUX_FPGA_INTERFACE_ADDR + 0x38);
+ writel(pinmux->uart0_usefpga, ARRIA10_PINMUX_FPGA_INTERFACE_ADDR + 0x3c);
+ writel(pinmux->uart1_usefpga, ARRIA10_PINMUX_FPGA_INTERFACE_ADDR + 0x40);
+
+ arria10_reset_deassert_fpga_peripherals();
+
+ INIT_LL();
+}
diff --git a/arch/arm/mach-socfpga/arria10-reset-manager.c b/arch/arm/mach-socfpga/arria10-reset-manager.c
new file mode 100644
index 000000000000..7a7c224e9989
--- /dev/null
+++ b/arch/arm/mach-socfpga/arria10-reset-manager.c
@@ -0,0 +1,422 @@
+/*
+ * Copyright (C) 2014-2016 Altera Corporation <www.altera.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <io.h>
+#include <mach/arria10-regs.h>
+#include <mach/arria10-reset-manager.h>
+#include <mach/arria10-system-manager.h>
+
+void arria10_reset_peripherals(void)
+{
+ unsigned mask_ecc_ocp = ARRIA10_RSTMGR_PER0MODRST_EMACECC0 |
+ ARRIA10_RSTMGR_PER0MODRST_EMACECC1 |
+ ARRIA10_RSTMGR_PER0MODRST_EMACECC2 |
+ ARRIA10_RSTMGR_PER0MODRST_USBECC0 |
+ ARRIA10_RSTMGR_PER0MODRST_USBECC1 |
+ ARRIA10_RSTMGR_PER0MODRST_NANDECC |
+ ARRIA10_RSTMGR_PER0MODRST_QSPIECC |
+ ARRIA10_RSTMGR_PER0MODRST_SDMMCECC;
+
+ /* disable all components except ECC_OCP, L4 Timer0 and L4 WD0 */
+ writel(0xffffffff, ARRIA10_RSTMGR_ADDR + ARRIA10_RSTMGR_PER1MODRST);
+ setbits_le32(ARRIA10_RSTMGR_ADDR + ARRIA10_RSTMGR_PER0MODRST,
+ ~mask_ecc_ocp);
+
+ /* Finally disable the ECC_OCP */
+ setbits_le32(ARRIA10_RSTMGR_ADDR + ARRIA10_RSTMGR_PER0MODRST,
+ mask_ecc_ocp);
+}
+
+void arria10_reset_deassert_dedicated_peripherals(void)
+{
+ uint32_t mask0 = 0;
+ uint32_t mask1 = 0;
+ uint32_t mask = 0;
+
+ mask |= ARRIA10_RSTMGR_PER0MODRST_SDMMCECC;
+ mask |= ARRIA10_RSTMGR_PER0MODRST_QSPIECC;
+ mask |= ARRIA10_RSTMGR_PER0MODRST_NANDECC;
+ mask |= ARRIA10_RSTMGR_PER0MODRST_DMAECC;
+
+ /* enable ECC OCP first */
+ clrbits_le32(ARRIA10_RSTMGR_ADDR + ARRIA10_RSTMGR_PER0MODRST, mask);
+
+ mask = 0;
+ mask |= ARRIA10_RSTMGR_PER0MODRST_SDMMC;
+ mask |= ARRIA10_RSTMGR_PER0MODRST_QSPI;
+ mask |= ARRIA10_RSTMGR_PER0MODRST_NAND;
+ mask |= ARRIA10_RSTMGR_PER0MODRST_DMA;
+
+ clrbits_le32(ARRIA10_RSTMGR_ADDR + ARRIA10_RSTMGR_PER0MODRST, mask);
+
+ mask = ARRIA10_RSTMGR_PER1MODRST_L4SYSTMR0;
+
+ mask |= ARRIA10_RSTMGR_PER1MODRST_UART1;
+ mask |= ARRIA10_RSTMGR_PER1MODRST_UART0;
+
+ clrbits_le32(ARRIA10_RSTMGR_ADDR + ARRIA10_RSTMGR_PER1MODRST, mask);
+
+ mask1 |= ARRIA10_RSTMGR_PER1MODRST_I2C3;
+ mask1 |= ARRIA10_RSTMGR_PER1MODRST_I2C4;
+ mask1 |= ARRIA10_RSTMGR_PER1MODRST_I2C2;
+ mask0 |= ARRIA10_RSTMGR_PER0MODRST_EMACECC1 |
+ ARRIA10_RSTMGR_PER0MODRST_EMAC1;
+ mask0 |= ARRIA10_RSTMGR_PER0MODRST_EMACECC2 |
+ ARRIA10_RSTMGR_PER0MODRST_EMAC2;
+ mask0 |= ARRIA10_RSTMGR_PER0MODRST_EMACECC0 |
+ ARRIA10_RSTMGR_PER0MODRST_EMAC0;
+ mask0 |= ARRIA10_RSTMGR_PER0MODRST_SPIS0;
+ mask0 |= ARRIA10_RSTMGR_PER0MODRST_SPIM0;
+ mask1 |= ARRIA10_RSTMGR_PER1MODRST_UART1;
+ mask1 |= ARRIA10_RSTMGR_PER1MODRST_GPIO2;
+
+ clrbits_le32(ARRIA10_RSTMGR_ADDR + ARRIA10_RSTMGR_PER0MODRST,
+ mask & ECC_MASK);
+ clrbits_le32(ARRIA10_RSTMGR_ADDR + ARRIA10_RSTMGR_PER1MODRST, mask1);
+ clrbits_le32(ARRIA10_RSTMGR_ADDR + ARRIA10_RSTMGR_PER0MODRST, mask0);
+}
+
+static const uint32_t per0fpgamasks[] = {
+ ARRIA10_RSTMGR_PER0MODRST_EMACECC0 |
+ ARRIA10_RSTMGR_PER0MODRST_EMAC0,
+ ARRIA10_RSTMGR_PER0MODRST_EMACECC1 |
+ ARRIA10_RSTMGR_PER0MODRST_EMAC1,
+ ARRIA10_RSTMGR_PER0MODRST_EMACECC2 |
+ ARRIA10_RSTMGR_PER0MODRST_EMAC2,
+ 0, /* i2c0 per1mod */
+ 0, /* i2c1 per1mod */
+ 0, /* i2c0_emac */
+ 0, /* i2c1_emac */
+ 0, /* i2c2_emac */
+ ARRIA10_RSTMGR_PER0MODRST_NANDECC |
+ ARRIA10_RSTMGR_PER0MODRST_NAND,
+ ARRIA10_RSTMGR_PER0MODRST_QSPIECC |
+ ARRIA10_RSTMGR_PER0MODRST_QSPI,
+ ARRIA10_RSTMGR_PER0MODRST_SDMMCECC |
+ ARRIA10_RSTMGR_PER0MODRST_SDMMC,
+ ARRIA10_RSTMGR_PER0MODRST_SPIM0,
+ ARRIA10_RSTMGR_PER0MODRST_SPIM1,
+ ARRIA10_RSTMGR_PER0MODRST_SPIS0,
+ ARRIA10_RSTMGR_PER0MODRST_SPIS1,
+ 0, /* uart0 per1mod */
+ 0, /* uart1 per1mod */
+};
+
+static const uint32_t per1fpgamasks[] = {
+ 0, /* emac0 per0mod */
+ 0, /* emac1 per0mod */
+ 0, /* emac2 per0mod */
+ ARRIA10_RSTMGR_PER1MODRST_I2C0,
+ ARRIA10_RSTMGR_PER1MODRST_I2C1,
+ ARRIA10_RSTMGR_PER1MODRST_I2C2, /* i2c0_emac */
+ ARRIA10_RSTMGR_PER1MODRST_I2C3, /* i2c1_emac */
+ ARRIA10_RSTMGR_PER1MODRST_I2C4, /* i2c2_emac */
+ 0, /* nand per0mod */
+ 0, /* qspi per0mod */
+ 0, /* sdmmc per0mod */
+ 0, /* spim0 per0mod */
+ 0, /* spim1 per0mod */
+ 0, /* spis0 per0mod */
+ 0, /* spis1 per0mod */
+ ARRIA10_RSTMGR_PER1MODRST_UART0,
+ ARRIA10_RSTMGR_PER1MODRST_UART1,
+};
+
+void arria10_reset_deassert_fpga_peripherals(void)
+{
+ uint32_t mask0 = 0;
+ uint32_t mask1 = 0;
+ uint32_t fpga_pinux_addr = ARRIA10_PINMUX_FPGA_INTERFACE_ADDR;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(per1fpgamasks); i++) {
+ if (readl(fpga_pinux_addr)) {
+ mask0 |= per0fpgamasks[i];
+ mask1 |= per1fpgamasks[i];
+ }
+ fpga_pinux_addr += sizeof(uint32_t);
+ }
+
+ clrbits_le32(ARRIA10_RSTMGR_ADDR + ARRIA10_RSTMGR_PER0MODRST,
+ mask0 & ECC_MASK);
+ clrbits_le32(ARRIA10_RSTMGR_ADDR + ARRIA10_RSTMGR_PER1MODRST, mask1);
+ clrbits_le32(ARRIA10_RSTMGR_ADDR + ARRIA10_RSTMGR_PER0MODRST, mask0);
+}
+
+void arria10_reset_deassert_shared_peripherals_q1(uint32_t *mask0,
+ uint32_t *mask1,
+ uint32_t *pinmux_addr)
+{
+ int i;
+
+ for (i = 1; i <= 12; i++, *pinmux_addr += sizeof(uint32_t)) {
+ switch (readl(*pinmux_addr)) {
+ case 15:
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_GPIO0;
+ break;
+ case 14:
+ *mask0 |= ARRIA10_RSTMGR_PER0MODRST_NANDECC|
+ ARRIA10_RSTMGR_PER0MODRST_NAND;
+ break;
+ case 13:
+ if ((i >= 1) && (i <= 4))
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_UART0;
+ else if ((i >= 5) && (i <= 8))
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_UART1;
+ break;
+ case 12:
+ if ((i >= 5) && (i <= 6))
+ *mask0 |=
+ ARRIA10_RSTMGR_PER0MODRST_QSPIECC |
+ ARRIA10_RSTMGR_PER0MODRST_QSPI;
+ break;
+ case 8:
+ *mask0 |= ARRIA10_RSTMGR_PER0MODRST_USBECC0 |
+ ARRIA10_RSTMGR_PER0MODRST_USB0;
+ break;
+ case 4:
+ if ((i >= 1) && (i <= 10))
+ *mask0 |=
+ ARRIA10_RSTMGR_PER0MODRST_SDMMCECC |
+ ARRIA10_RSTMGR_PER0MODRST_SDMMC;
+ break;
+ case 3:
+ if ((i == 1) || ((i >= 5) && (i <= 8)))
+ *mask0 |= ARRIA10_RSTMGR_PER0MODRST_SPIM0;
+ else if ((i == 2) || ((i >= 9) && (i <= 12)))
+ *mask0 |= ARRIA10_RSTMGR_PER0MODRST_SPIM1;
+ break;
+ case 2:
+ if ((i >= 1) && (i <= 4))
+ *mask0 |= ARRIA10_RSTMGR_PER0MODRST_SPIS0;
+ else if ((i >= 9) && (i <= 12))
+ *mask0 |= ARRIA10_RSTMGR_PER0MODRST_SPIS1;
+ break;
+ case 1:
+ if ((i == 7) || (i == 8))
+ *mask0 |=
+ ARRIA10_RSTMGR_PER0MODRST_EMACECC2 |
+ ARRIA10_RSTMGR_PER0MODRST_EMAC2;
+ else if ((i == 9) || (i == 10))
+ *mask0 |=
+ ARRIA10_RSTMGR_PER0MODRST_EMACECC1 |
+ ARRIA10_RSTMGR_PER0MODRST_EMAC1;
+ else if ((i == 11) || (1 == 12))
+ *mask0 |=
+ ARRIA10_RSTMGR_PER0MODRST_EMACECC0 |
+ ARRIA10_RSTMGR_PER0MODRST_EMAC0;
+ break;
+ case 0:
+ if ((i == 3) || (i == 4))
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_I2C1;
+ else if ((i == 5) || (i == 6))
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_I2C0;
+ else if ((i == 7) || (i == 8))
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_I2C4;
+ else if ((i == 9) || (i == 10))
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_I2C3;
+ else if ((i == 11) || (i == 12))
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_I2C2;
+ break;
+ }
+ }
+}
+
+void arria10_reset_deassert_shared_peripherals_q2(uint32_t *mask0,
+ uint32_t *mask1,
+ uint32_t *pinmux_addr)
+{
+ int i;
+
+ for (i = 1; i <= 12; i++, *pinmux_addr += sizeof(uint32_t)) {
+ switch (readl(*pinmux_addr)) {
+ case 15:
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_GPIO0;
+ break;
+ case 14:
+ if ((i != 4) && (i != 5))
+ *mask0 |=
+ ARRIA10_RSTMGR_PER0MODRST_NANDECC |
+ ARRIA10_RSTMGR_PER0MODRST_NAND;
+ break;
+ case 13:
+ if ((i >= 9) && (i <= 12))
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_UART0;
+ break;
+ case 8:
+ *mask0 |= ARRIA10_RSTMGR_PER0MODRST_USBECC1 |
+ ARRIA10_RSTMGR_PER0MODRST_USB1;
+ break;
+ case 4:
+ *mask0 |= ARRIA10_RSTMGR_PER0MODRST_EMACECC0 |
+ ARRIA10_RSTMGR_PER0MODRST_EMAC0;
+ break;
+ case 3:
+ if ((i >= 8) && (i <= 12))
+ *mask0 |= ARRIA10_RSTMGR_PER0MODRST_SPIM1;
+ break;
+ case 2:
+ if ((i >= 9) && (i <= 12))
+ *mask0 |= ARRIA10_RSTMGR_PER0MODRST_SPIS0;
+ break;
+ case 0:
+ if ((i == 9) || (i == 10))
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_I2C1;
+ else if ((i == 11) || (i == 12))
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_I2C0;
+ break;
+ }
+ }
+}
+
+void arria10_reset_deassert_shared_peripherals_q3(uint32_t *mask0,
+ uint32_t *mask1,
+ uint32_t *pinmux_addr)
+{
+ int i;
+
+ for (i = 1; i <= 12; i++, *pinmux_addr += sizeof(uint32_t)) {
+ switch (readl(*pinmux_addr)) {
+ case 15:
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_GPIO1;
+ break;
+ case 14:
+ *mask0 |= ARRIA10_RSTMGR_PER0MODRST_NANDECC |
+ ARRIA10_RSTMGR_PER0MODRST_NAND;
+ break;
+ case 13:
+ if ((i >= 1) && (i <= 4))
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_UART0;
+ else if ((i >= 5) && (i <= 8))
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_UART1;
+ break;
+ case 8:
+ *mask0 |= ARRIA10_RSTMGR_PER0MODRST_EMACECC1 |
+ ARRIA10_RSTMGR_PER0MODRST_EMAC1;
+ break;
+ case 3:
+ if ((i >= 1) && (i <= 5))
+ *mask0 |= ARRIA10_RSTMGR_PER0MODRST_SPIM1;
+ break;
+ case 2:
+ if ((i >= 5) && (i <= 8))
+ *mask0 |= ARRIA10_RSTMGR_PER0MODRST_SPIS1;
+ else if ((i >= 9) && (i <= 12))
+ *mask0 |= ARRIA10_RSTMGR_PER0MODRST_SPIS0;
+ break;
+ case 1:
+ if ((i == 9) || (i == 10))
+ *mask0 |=
+ ARRIA10_RSTMGR_PER0MODRST_EMACECC2 |
+ ARRIA10_RSTMGR_PER0MODRST_EMAC2;
+ else if ((i == 11) || (i == 12))
+ *mask0 |=
+ ARRIA10_RSTMGR_PER0MODRST_EMACECC0 |
+ ARRIA10_RSTMGR_PER0MODRST_EMAC0;
+ break;
+ case 0:
+ if ((i == 7) || (i == 8))
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_I2C1;
+ else if ((i == 3) || (i == 4))
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_I2C0;
+ else if ((i == 9) || (i == 10))
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_I2C4;
+ else if ((i == 11) || (i == 12))
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_I2C2;
+ break;
+ }
+ }
+}
+
+void arria10_reset_deassert_shared_peripherals_q4(uint32_t *mask0, uint32_t *mask1,
+ uint32_t *pinmux_addr)
+{
+ int i;
+
+ for (i = 1; i <= 12; i++, *pinmux_addr += sizeof(uint32_t)) {
+ switch (readl(*pinmux_addr)) {
+ case 15:
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_GPIO1;
+ break;
+ case 14:
+ if (i != 4)
+ *mask0 |= ARRIA10_RSTMGR_PER0MODRST_NANDECC |
+ ARRIA10_RSTMGR_PER0MODRST_NAND;
+ break;
+ case 13:
+ if ((i >= 3) && (i <= 6))
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_UART1;
+ break;
+ case 12:
+ if ((i == 5) || (i == 6))
+ *mask0 |= ARRIA10_RSTMGR_PER0MODRST_QSPIECC |
+ ARRIA10_RSTMGR_PER0MODRST_QSPI;
+ break;
+ case 8:
+ *mask0 |= ARRIA10_RSTMGR_PER0MODRST_EMACECC2 |
+ ARRIA10_RSTMGR_PER0MODRST_EMAC2;
+ break;
+ case 4:
+ if ((i >= 1) && (i <= 6))
+ *mask0 |= ARRIA10_RSTMGR_PER0MODRST_SDMMCECC |
+ ARRIA10_RSTMGR_PER0MODRST_SDMMC;
+ break;
+ case 3:
+ if ((i >= 6) && (i <= 12))
+ *mask0 |= ARRIA10_RSTMGR_PER0MODRST_SPIM0;
+ break;
+ case 2:
+ if ((i >= 9) && (i <= 12))
+ *mask0 |= ARRIA10_RSTMGR_PER0MODRST_SPIS1;
+ break;
+ case 1:
+ if ((i == 7) || (i == 8))
+ *mask0 |= ARRIA10_RSTMGR_PER0MODRST_EMACECC1 |
+ ARRIA10_RSTMGR_PER0MODRST_EMAC1;
+ else if ((i == 11) || (i == 12))
+ *mask0 |= ARRIA10_RSTMGR_PER0MODRST_EMACECC0 |
+ ARRIA10_RSTMGR_PER0MODRST_EMAC0;
+ break;
+ case 0:
+ if ((i == 1) || (i == 2))
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_I2C1;
+ else if ((i == 7) || (i == 8))
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_I2C3;
+ else if ((i == 9) || (i == 10))
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_I2C4;
+ else if ((i == 11) || (i == 12))
+ *mask1 |= ARRIA10_RSTMGR_PER1MODRST_I2C2;
+ break;
+ }
+ }
+}
+
+void arria10_reset_deassert_shared_peripherals(void)
+{
+ uint32_t mask0 = 0;
+ uint32_t mask1 = 0;
+ uint32_t pinmux_addr = ARRIA10_PINMUX_SHARED_3V_IO_ADDR;
+
+ arria10_reset_deassert_shared_peripherals_q1(&mask0, &mask1,
+ &pinmux_addr);
+ arria10_reset_deassert_shared_peripherals_q2(&mask0, &mask1,
+ &pinmux_addr);
+ arria10_reset_deassert_shared_peripherals_q3(&mask0, &mask1,
+ &pinmux_addr);
+ arria10_reset_deassert_shared_peripherals_q4(&mask0, &mask1,
+ &pinmux_addr);
+ mask1 |= ARRIA10_RSTMGR_PER1MODRST_L4WD1 |
+ ARRIA10_RSTMGR_PER1MODRST_L4SYSTMR1 |
+ ARRIA10_RSTMGR_PER1MODRST_SPTMR0 |
+ ARRIA10_RSTMGR_PER1MODRST_SPTMR1;
+
+ clrbits_le32(ARRIA10_RSTMGR_ADDR + ARRIA10_RSTMGR_PER0MODRST,
+ mask0 & ECC_MASK);
+ clrbits_le32(ARRIA10_RSTMGR_ADDR + ARRIA10_RSTMGR_PER1MODRST, mask1);
+ clrbits_le32(ARRIA10_RSTMGR_ADDR + ARRIA10_RSTMGR_PER0MODRST, mask0);
+}
diff --git a/arch/arm/mach-socfpga/arria10-sdram.c b/arch/arm/mach-socfpga/arria10-sdram.c
new file mode 100644
index 000000000000..a18a0abf14bf
--- /dev/null
+++ b/arch/arm/mach-socfpga/arria10-sdram.c
@@ -0,0 +1,557 @@
+/*
+ * Copyright (C) 2014-2016 Altera Corporation <www.altera.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+#include <common.h>
+#include <io.h>
+#include <debug_ll.h>
+#include <mach/arria10-sdram.h>
+#include <mach/arria10-regs.h>
+#include <mach/arria10-reset-manager.h>
+
+
+/* FAWBANK - Number of Bank of a given device involved in the FAW period. */
+#define ARRIA10_SDR_ACTIVATE_FAWBANK (0x1)
+
+#define ARRIA10_EMIF_RST 31
+#define ARRIA10_OCT_CAL_REQ 30
+#define ARRIA10_OCT_CAL_ACK 31
+
+#define ARRIA10_NIOS_OCT_DONE 7
+#define ARRIA10_NIOS_OCT_ACK 7
+
+/* Engineering sample silicon */
+#define ARRIA10_ES_SILICON_VER 0x00010001
+
+#define DDR_REG_SEQ2CORE 0xFFD0507C
+#define DDR_REG_CORE2SEQ 0xFFD05078
+#define DDR_REG_GPOUT 0xFFD03010
+#define DDR_REG_GPIN 0xFFD03014
+#define DDR_MAX_TRIES 0x00100000
+#define IO48_MMR_DRAMSTS 0xFFCFA0EC
+#define IO48_MMR_NIOS2_RESERVE0 0xFFCFA110
+#define IO48_MMR_NIOS2_RESERVE1 0xFFCFA114
+#define IO48_MMR_NIOS2_RESERVE2 0xFFCFA118
+
+#define SEQ2CORE_MASK 0xF
+#define CORE2SEQ_INT_REQ 0xF
+#define SEQ2CORE_INT_RESP_BIT 3
+
+#define DDR_ECC_DMA_SIZE 1500
+#define DDR_READ_LATENCY_DELAY 40
+
+#define ARRIA_DDR_CONFIG(A, B, C, R) ((A<<24)|(B<<16)|(C<<8)|R)
+/* The followring are the supported configurations */
+uint32_t ddr_config[] = {
+ /* Chip - Row - Bank - Column Style */
+ /* All Types */
+ ARRIA_DDR_CONFIG(0, 3, 10, 12),
+ ARRIA_DDR_CONFIG(0, 3, 10, 13),
+ ARRIA_DDR_CONFIG(0, 3, 10, 14),
+ ARRIA_DDR_CONFIG(0, 3, 10, 15),
+ ARRIA_DDR_CONFIG(0, 3, 10, 16),
+ ARRIA_DDR_CONFIG(0, 3, 10, 17),
+ /* LPDDR x16 */
+ ARRIA_DDR_CONFIG(0, 3, 11, 14),
+ ARRIA_DDR_CONFIG(0, 3, 11, 15),
+ ARRIA_DDR_CONFIG(0, 3, 11, 16),
+ ARRIA_DDR_CONFIG(0, 3, 12, 15),
+ /* DDR4 Only */
+ ARRIA_DDR_CONFIG(0, 4, 10, 14),
+ ARRIA_DDR_CONFIG(0, 4, 10, 15),
+ ARRIA_DDR_CONFIG(0, 4, 10, 16),
+ ARRIA_DDR_CONFIG(0, 4, 10, 17), /* 14 */
+ /* Chip - Bank - Row - Column Style */
+ ARRIA_DDR_CONFIG(1, 3, 10, 12),
+ ARRIA_DDR_CONFIG(1, 3, 10, 13),
+ ARRIA_DDR_CONFIG(1, 3, 10, 14),
+ ARRIA_DDR_CONFIG(1, 3, 10, 15),
+ ARRIA_DDR_CONFIG(1, 3, 10, 16),
+ ARRIA_DDR_CONFIG(1, 3, 10, 17),
+ ARRIA_DDR_CONFIG(1, 3, 11, 14),
+ ARRIA_DDR_CONFIG(1, 3, 11, 15),
+ ARRIA_DDR_CONFIG(1, 3, 11, 16),
+ ARRIA_DDR_CONFIG(1, 3, 12, 15),
+ /* DDR4 Only */
+ ARRIA_DDR_CONFIG(1, 4, 10, 14),
+ ARRIA_DDR_CONFIG(1, 4, 10, 15),
+ ARRIA_DDR_CONFIG(1, 4, 10, 16),
+ ARRIA_DDR_CONFIG(1, 4, 10, 17),
+};
+#define DDR_CONFIG_ELEMENTS (sizeof(ddr_config)/sizeof(uint32_t))
+
+void udelay(unsigned long time)
+{
+ unsigned long i = 1000 * time;
+
+ while (i--)
+ ;
+}
+
+static int match_ddr_conf(uint32_t ddr_conf)
+{
+ int i;
+
+ for (i = 0; i < DDR_CONFIG_ELEMENTS; i++) {
+ if (ddr_conf == ddr_config[i])
+ return i;
+ }
+ return 0;
+}
+
+/* Check whether SDRAM is successfully Calibrated */
+static int is_sdram_cal_success(void)
+{
+ return readl(ARRIA10_ECC_HMC_OCP_DDRCALSTAT);
+}
+
+static unsigned char ddr_get_bit(uint32_t ereg, unsigned char bit)
+{
+ unsigned int reg = readl(ereg);
+
+ return (reg & (1 << bit)) ? 1 : 0;
+}
+
+static unsigned char ddr_wait_bit(uint32_t ereg, uint32_t bit,
+ uint32_t expected, uint32_t timeout_usec)
+{
+ unsigned int tmr;
+
+ for (tmr = 0; tmr < timeout_usec; tmr += 100) {
+ udelay(100);
+ if (ddr_get_bit(ereg, bit) == expected)
+ return 0;
+ }
+
+ return 1;
+}
+
+static void ddr_set_bit(uint32_t ereg, uint32_t bit)
+{
+ unsigned int tmp = readl(ereg);
+
+ tmp |= (1 << bit);
+ writel(tmp, ereg);
+}
+
+static void ddr_clr_bit(uint32_t ereg, uint32_t bit)
+{
+ unsigned int tmp = readl(ereg);
+
+ tmp &= ~(1 << bit);
+ writel(tmp, ereg);
+}
+
+static void ddr_delay(uint32_t delay)
+{
+ int tmr;
+
+ for (tmr = 0; tmr < delay; tmr++)
+ udelay(1000);
+}
+
+/*
+ * Diagram of OCT Workaround:
+ *
+ * EMIF Core HPS Processor OCT FSM
+ * =================================================================
+ *
+ * seq2core ==============>
+ * [0x?????????] OCT Request [0xFFD0507C]
+ *
+ * core2seq
+ * [0x?????????] <==============
+ * OCT Ready [0xFFD05078]
+ *
+ * [0xFFD03010] ============> Request
+ * OCT Request
+ *
+ * [0xFFD03014] <============ Ready
+ * OCT Ready
+ * Signal definitions:
+ *
+ * seq2core[7] - OCT calibration request (act-high)
+ * core2seq[7] - Signals OCT FSM is ready (active high)
+ * gpout[31] - EMIF Reset override (active low)
+ * gpout[30] - OCT calibration request (act-high)
+ * gpin[31] - OCT calibration ready (act-high)
+ */
+
+static int ddr_calibration_es_workaround(void)
+{
+ ddr_delay(500);
+ /* Step 1 - Initiating Reset Sequence */
+ ddr_clr_bit(DDR_REG_GPOUT, ARRIA10_EMIF_RST); /* Reset EMIF */
+ ddr_delay(10);
+
+ /* Step 2 - Clearing registers to EMIF core */
+ writel(0, DDR_REG_CORE2SEQ); /*Clear the HPS->NIOS COM reg.*/
+
+ /* Step 3 - Clearing registers to OCT core */
+ ddr_clr_bit(DDR_REG_GPOUT, ARRIA10_OCT_CAL_REQ); /* OCT Cal Request */
+ ddr_delay(5);
+
+ /* Step 4 - Taking EMIF out of reset */
+ ddr_set_bit(DDR_REG_GPOUT, ARRIA10_EMIF_RST);
+ ddr_delay(10);
+
+ /* Step 5 - Waiting for OCT circuitry to come out of reset */
+ if (ddr_wait_bit(DDR_REG_GPIN, ARRIA10_OCT_CAL_ACK, 1, 1000000))
+ return -1;
+
+ /* Step 6 - Allowing EMIF to proceed with OCT calibration */
+ ddr_set_bit(DDR_REG_CORE2SEQ, ARRIA10_NIOS_OCT_DONE);
+
+ /* Step 7 - Waiting for EMIF request */
+ if (ddr_wait_bit(DDR_REG_SEQ2CORE, ARRIA10_NIOS_OCT_ACK, 1, 2000000))
+ return -2;
+
+ /* Step 8 - Acknowledging EMIF OCT request */
+ ddr_clr_bit(DDR_REG_CORE2SEQ, ARRIA10_NIOS_OCT_DONE);
+
+ /* Step 9 - Waiting for EMIF response */
+ if (ddr_wait_bit(DDR_REG_SEQ2CORE, ARRIA10_NIOS_OCT_ACK, 0, 2000000))
+ return -3;
+
+ /* Step 10 - Triggering OCT Calibration */
+ ddr_set_bit(DDR_REG_GPOUT, ARRIA10_OCT_CAL_REQ);
+
+ /* Step 11 - Waiting for OCT response */
+ if (ddr_wait_bit(DDR_REG_GPIN, ARRIA10_OCT_CAL_ACK, 0, 1000))
+ return -4;
+
+ /* Step 12 - Clearing OCT Request bit */
+ ddr_clr_bit(DDR_REG_GPOUT, ARRIA10_OCT_CAL_REQ);
+
+ /* Step 13 - Waiting for OCT Engine */
+ if (ddr_wait_bit(DDR_REG_GPIN, ARRIA10_OCT_CAL_ACK, 1, 200000))
+ return -5;
+
+ /* Step 14 - Proceeding with EMIF calibration */
+ ddr_set_bit(DDR_REG_CORE2SEQ, ARRIA10_NIOS_OCT_DONE);
+
+ ddr_delay(100);
+
+ return 0;
+}
+
+static int emif_clear(void)
+{
+ uint32_t s2c;
+ uint32_t i = DDR_MAX_TRIES;
+
+ writel(0, DDR_REG_CORE2SEQ);
+ do {
+ ddr_delay(50);
+ s2c = readl(DDR_REG_SEQ2CORE);
+ } while ((s2c & SEQ2CORE_MASK) && (--i > 0));
+
+ return !i;
+}
+static int emif_reset(void)
+{
+ uint32_t c2s, s2c;
+
+ c2s = readl(DDR_REG_CORE2SEQ);
+ s2c = readl(DDR_REG_SEQ2CORE);
+
+ pr_debug("c2s=%08x s2c=%08x nr0=%08x nr1=%08x nr2=%08x dst=%08x\n",
+ c2s, s2c, readl(IO48_MMR_NIOS2_RESERVE0),
+ readl(IO48_MMR_NIOS2_RESERVE1),
+ readl(IO48_MMR_NIOS2_RESERVE2),
+ readl(IO48_MMR_DRAMSTS));
+
+ if ((s2c & SEQ2CORE_MASK) && emif_clear()) {
+ printf("failed emif_clear()\n");
+ return -1;
+ }
+
+ writel(CORE2SEQ_INT_REQ, DDR_REG_CORE2SEQ);
+
+ if (ddr_wait_bit(DDR_REG_SEQ2CORE, SEQ2CORE_INT_RESP_BIT, 0, 1000000)) {
+ printf("emif_reset failed to see interrupt acknowledge\n");
+ return -2;
+ } else {
+ printf("emif_reset interrupt acknowledged\n");
+ }
+
+ if (emif_clear()) {
+ printf("emif_clear() failed\n");
+ return -3;
+ }
+ pr_debug("emif_reset interrupt cleared\n");
+
+ pr_debug("nr0=%08x nr1=%08x nr2=%08x\n",
+ readl(IO48_MMR_NIOS2_RESERVE0),
+ readl(IO48_MMR_NIOS2_RESERVE1),
+ readl(IO48_MMR_NIOS2_RESERVE2));
+
+ return 0;
+}
+
+static int arria10_ddr_setup(void)
+{
+ int i, j, retcode, ddr_setup_complete = 0;
+ int chip_version = readl(ARRIA10_SYSMGR_SILICONID1);
+
+ /* Try 3 times to do a calibration */
+ for (i = 0; (i < 3) && !ddr_setup_complete; i++) {
+ /* Only engineering sample needs calibration workaround */
+ if (ARRIA10_ES_SILICON_VER == chip_version) {
+ retcode = ddr_calibration_es_workaround();
+ if (retcode) {
+ printf("DDRCAL: Failure: %d\n", retcode);
+ continue;
+ }
+ }
+
+ /* A delay to wait for calibration bit to set */
+ for (j = 0; (j < 10) && !ddr_setup_complete; j++) {
+ ddr_delay(500);
+ ddr_setup_complete = is_sdram_cal_success();
+ }
+
+ if (!ddr_setup_complete &&
+ (ARRIA10_ES_SILICON_VER != chip_version)) {
+ emif_reset();
+ }
+ }
+
+ if (!ddr_setup_complete) {
+ puts_ll("Error: Could Not Calibrate SDRAM\n");
+ return -1;
+ }
+
+ return 0;
+}
+
+/* Function to startup the SDRAM*/
+static int arria10_sdram_startup(void)
+{
+ uint32_t val;
+ /* Release NOC ddr scheduler from reset */
+ val = readl(ARRIA10_RSTMGR_ADDR + ARRIA10_RSTMGR_BRGMODRST);
+ val &= ~ARRIA10_RSTMGR_BRGMODRST_DDRSCH;
+ writel(val, ARRIA10_RSTMGR_ADDR + ARRIA10_RSTMGR_BRGMODRST);
+
+ /* Bringup the DDR (calibration and configuration) */
+ return arria10_ddr_setup();
+}
+
+/* Function to initialize SDRAM MMR and NOC DDR scheduler*/
+static void arria10_sdram_mmr_init(void)
+{
+ uint32_t update_value, io48_value;
+ union ctrlcfg0_reg ctrlcfg0 =
+ (union ctrlcfg0_reg)readl(ARRIA10_IO48_HMC_MMR_CTRLCFG0);
+ union ctrlcfg1_reg ctrlcfg1 =
+ (union ctrlcfg1_reg)readl(ARRIA10_IO48_HMC_MMR_CTRLCFG1);
+ union dramaddrw_reg dramaddrw =
+ (union dramaddrw_reg)readl(ARRIA10_IO48_HMC_MMR_DRAMADDRW);
+ union caltiming0_reg caltim0 =
+ (union caltiming0_reg)readl(ARRIA10_IO48_HMC_MMR_CALTIMING0);
+ union caltiming1_reg caltim1 =
+ (union caltiming1_reg)readl(ARRIA10_IO48_HMC_MMR_CALTIMING1);
+ union caltiming2_reg caltim2 =
+ (union caltiming2_reg)readl(ARRIA10_IO48_HMC_MMR_CALTIMING2);
+ union caltiming3_reg caltim3 =
+ (union caltiming3_reg)readl(ARRIA10_IO48_HMC_MMR_CALTIMING3);
+ union caltiming4_reg caltim4 =
+ (union caltiming4_reg)readl(ARRIA10_IO48_HMC_MMR_CALTIMING4);
+ union caltiming9_reg caltim9 =
+ (union caltiming9_reg)readl(ARRIA10_IO48_HMC_MMR_CALTIMING9);
+ uint32_t ddrioctl;
+
+ /*
+ * Configure the DDR IO size [0xFFCFB008]
+ * niosreserve0: Used to indicate DDR width &
+ * bit[7:0] = Number of data bits (0x20 for 32bit)
+ * bit[8] = 1 if user-mode OCT is present
+ * bit[9] = 1 if warm reset compiled into EMIF Cal Code
+ * bit[10] = 1 if warm reset is on during generation in EMIF Cal
+ * niosreserve1: IP ADCDS version encoded as 16 bit value
+ * bit[2:0] = Variant (0=not special,1=FAE beta, 2=Customer beta,
+ * 3=EAP, 4-6 are reserved)
+ * bit[5:3] = Service Pack # (e.g. 1)
+ * bit[9:6] = Minor Release #
+ * bit[14:10] = Major Release #
+ */
+ if ((readl(ARRIA10_IO48_HMC_MMR_NIOSRESERVE1) >> 6) & 0x1FF) {
+ update_value = readl(ARRIA10_IO48_HMC_MMR_NIOSRESERVE0);
+ writel(((update_value & 0xFF) >> 5),
+ ARRIA10_ECC_HMC_OCP_DDRIOCTRL);
+ }
+
+ ddrioctl = readl(ARRIA10_ECC_HMC_OCP_DDRIOCTRL);
+
+ /* Set the DDR Configuration [0xFFD12400] */
+ io48_value = ARRIA_DDR_CONFIG(ctrlcfg1.cfg_addr_order,
+ (dramaddrw.cfg_bank_addr_width +
+ dramaddrw.cfg_bank_group_addr_width),
+ dramaddrw.cfg_col_addr_width,
+ dramaddrw.cfg_row_addr_width);
+
+ update_value = match_ddr_conf(io48_value);
+ if (update_value)
+ writel(update_value, ARRIA10_NOC_DDR_T_MAIN_SCHEDULER_DDRCONF);
+
+ /*
+ * Configure DDR timing [0xFFD1240C]
+ * RDTOMISS = tRTP + tRP + tRCD - BL/2
+ * WRTOMISS = WL + tWR + tRP + tRCD and
+ * WL = RL + BL/2 + 2 - rd-to-wr ; tWR = 15ns so...
+ * First part of equation is in memory clock units so divide by 2
+ * for HMC clock units. 1066MHz is close to 1ns so use 15 directly.
+ * WRTOMISS = ((RL + BL/2 + 2 + tWR) >> 1)- rd-to-wr + tRP + tRCD
+ */
+ update_value = (caltim2.cfg_rd_to_pch + caltim4.cfg_pch_to_valid +
+ caltim0.cfg_act_to_rdwr -
+ (ctrlcfg0.cfg_ctrl_burst_len >> 2));
+ io48_value = ((((readl(ARRIA10_IO48_HMC_MMR_DRAMTIMING0) &
+ ARRIA10_IO48_DRAMTIME_MEM_READ_LATENCY) + 2 + 15 +
+ (ctrlcfg0.cfg_ctrl_burst_len >> 1)) >> 1) -
+ /* Up to here was in memory cycles so divide by 2 */
+ caltim1.cfg_rd_to_wr + caltim0.cfg_act_to_rdwr +
+ caltim4.cfg_pch_to_valid);
+
+ writel(((caltim0.cfg_act_to_act <<
+ ARRIA10_NOC_MPU_DDR_T_SCHED_DDRTIMING_ACTTOACT_LSB) |
+ (update_value <<
+ ARRIA10_NOC_MPU_DDR_T_SCHED_DDRTIMING_RDTOMISS_LSB) |
+ (io48_value <<
+ ARRIA10_NOC_MPU_DDR_T_SCHED_DDRTIMING_WRTOMISS_LSB) |
+ ((ctrlcfg0.cfg_ctrl_burst_len >> 2) <<
+ ARRIA10_NOC_MPU_DDR_T_SCHED_DDRTIMING_BURSTLEN_LSB) |
+ (caltim1.cfg_rd_to_wr <<
+ ARRIA10_NOC_MPU_DDR_T_SCHED_DDRTIMING_RDTOWR_LSB) |
+ (caltim3.cfg_wr_to_rd <<
+ ARRIA10_NOC_MPU_DDR_T_SCHED_DDRTIMING_WRTORD_LSB) |
+ (((ddrioctl == 1) ? 1 : 0) <<
+ ARRIA10_NOC_MPU_DDR_T_SCHED_DDRTIMING_BWRATIO_LSB)),
+ ARRIA10_NOC_DDR_T_MAIN_SCHEDULER_DDRTIMING);
+
+ /* Configure DDR mode [0xFFD12410] [precharge = 0] */
+ writel(((ddrioctl ? 0 : 1) <<
+ ARRIA10_NOC_MPU_DDR_T_SCHED_DDRMOD_BWRATIOEXTENDED_LSB),
+ ARRIA10_NOC_DDR_T_MAIN_SCHEDULER_DDRMODE);
+
+ /* Configure the read latency [0xFFD12414] */
+ writel(((readl(ARRIA10_IO48_HMC_MMR_DRAMTIMING0) &
+ ARRIA10_IO48_DRAMTIME_MEM_READ_LATENCY) >> 1) +
+ DDR_READ_LATENCY_DELAY,
+ ARRIA10_NOC_DDR_T_MAIN_SCHEDULER_READLATENCY);
+
+ /*
+ * Configuring timing values concerning activate commands
+ * [0xFFD12438] [FAWBANK alway 1 because always 4 bank DDR]
+ */
+ writel(((caltim0.cfg_act_to_act_db <<
+ ARRIA10_NOC_MPU_DDR_T_SCHED_ACTIVATE_RRD_LSB) |
+ (caltim9.cfg_4_act_to_act <<
+ ARRIA10_NOC_MPU_DDR_T_SCHED_ACTIVATE_FAW_LSB) |
+ (ARRIA10_SDR_ACTIVATE_FAWBANK <<
+ ARRIA10_NOC_MPU_DDR_T_SCHED_ACTIVATE_FAWBANK_LSB)),
+ ARRIA10_NOC_DDR_T_MAIN_SCHEDULER_ACTIVATE);
+
+ /*
+ * Configuring timing values concerning device to device data bus
+ * ownership change [0xFFD1243C]
+ */
+ writel(((caltim1.cfg_rd_to_rd_dc <<
+ ARRIA10_NOC_MPU_DDR_T_SCHED_DEVTODEV_BUSRDTORD_LSB) |
+ (caltim1.cfg_rd_to_wr_dc <<
+ ARRIA10_NOC_MPU_DDR_T_SCHED_DEVTODEV_BUSRDTOWR_LSB) |
+ (caltim3.cfg_wr_to_rd_dc <<
+ ARRIA10_NOC_MPU_DDR_T_SCHED_DEVTODEV_BUSWRTORD_LSB)),
+ ARRIA10_NOC_DDR_T_MAIN_SCHEDULER_DEVTODEV);
+
+ /* Enable or disable the SDRAM ECC */
+ if (ctrlcfg1.cfg_ctrl_enable_ecc) {
+ setbits_le32(ARRIA10_ECC_HMC_OCP_MPR_ECCCTRL1,
+ (ARRIA10_ECC_HMC_OCP_ECCCTL_AWB_CNT_RST |
+ ARRIA10_ECC_HMC_OCP_ECCCTL_CNT_RST |
+ ARRIA10_ECC_HMC_OCP_ECCCTL_ECC_EN));
+ clrbits_le32(ARRIA10_ECC_HMC_OCP_MPR_ECCCTRL1,
+ (ARRIA10_ECC_HMC_OCP_ECCCTL_AWB_CNT_RST |
+ ARRIA10_ECC_HMC_OCP_ECCCTL_CNT_RST));
+ setbits_le32(ARRIA10_ECC_HMC_OCP_MPR_ECCCTRL2,
+ (ARRIA10_ECC_HMC_OCP_ECCCTL2_RMW_EN |
+ ARRIA10_ECC_HMC_OCP_ECCCTL2_AWB_EN));
+ } else {
+ clrbits_le32(ARRIA10_ECC_HMC_OCP_MPR_ECCCTRL1,
+ (ARRIA10_ECC_HMC_OCP_ECCCTL_AWB_CNT_RST |
+ ARRIA10_ECC_HMC_OCP_ECCCTL_CNT_RST |
+ ARRIA10_ECC_HMC_OCP_ECCCTL_ECC_EN));
+ clrbits_le32(ARRIA10_ECC_HMC_OCP_MPR_ECCCTRL2,
+ (ARRIA10_ECC_HMC_OCP_ECCCTL2_RMW_EN |
+ ARRIA10_ECC_HMC_OCP_ECCCTL2_AWB_EN));
+ }
+}
+
+static int arria10_sdram_firewall_setup(void)
+{
+ uint32_t mpu_en = 0;
+
+ /* set to default state */
+ writel(0x00000000, ARRIA10_SDR_FW_MPU_FPGA_EN);
+ writel(0x00000000, ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x00);
+
+ writel(0xffff0000, ARRIA10_SDR_FW_MPU_FPGA_MPUREGION0ADDR);
+
+ mpu_en |= ARRIA10_NOC_FW_DDR_MPU_MPUREG0EN;
+
+ writel(mpu_en, ARRIA10_SDR_FW_MPU_FPGA_EN);
+ writel(0x00000000, ARRIA10_SDR_FW_MPU_FPGA_MPUREGION1ADDR);
+ writel(0x00000000, ARRIA10_SDR_FW_MPU_FPGA_MPUREGION2ADDR);
+ writel(0x00000000, ARRIA10_SDR_FW_MPU_FPGA_MPUREGION3ADDR);
+ writel(0xffff0000, ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM0REGION0ADDR);
+
+ mpu_en |= ARRIA10_NOC_FW_DDR_MPU_MPUREG1EN;
+ writel(mpu_en, ARRIA10_SDR_FW_MPU_FPGA_EN);
+
+ writel(0x00000000, ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM0REGION1ADDR);
+ writel(0x00000000, ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM0REGION2ADDR);
+ writel(0x00000000, ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM0REGION3ADDR);
+ writel(0xffff0000, ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM1REGION0ADDR);
+
+ mpu_en |= ARRIA10_NOC_FW_DDR_MPU_MPUREG2EN;
+ writel(mpu_en, ARRIA10_SDR_FW_MPU_FPGA_EN);
+
+ writel(0x00000000, ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM1REGION1ADDR);
+ writel(0x00000000, ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM1REGION2ADDR);
+ writel(0x00000000, ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM1REGION3ADDR);
+ writel(0xffff0000, ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM2REGION0ADDR);
+
+ mpu_en |= ARRIA10_NOC_FW_DDR_MPU_MPUREG3EN;
+ writel(mpu_en, ARRIA10_SDR_FW_MPU_FPGA_EN);
+
+ writel(0x00000000, ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM2REGION1ADDR);
+ writel(0x00000000, ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM2REGION2ADDR);
+ writel(0x00000000, ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM2REGION3ADDR);
+
+ writel(0xffff0000, ARRIA10_NOC_FW_DDR_L3_HPSREGION0ADDR);
+ writel(ARRIA10_NOC_FW_DDR_L3_HPSREG0EN, ARRIA10_NOC_FW_DDR_L3_EN);
+
+ return 0;
+}
+
+int arria10_ddr_calibration_sequence(void)
+{
+ /* Check to see if SDRAM cal was success */
+ if (arria10_sdram_startup()) {
+ puts_ll("DDRCAL: Failed\n");
+ return -1;
+ }
+
+ puts_ll("DDRCAL: Success\n");
+
+ /* initialize the MMR register */
+ arria10_sdram_mmr_init();
+
+ if (arria10_sdram_firewall_setup())
+ puts_ll("FW: Error Configuring Firewall\n");
+
+ return 0;
+}
diff --git a/arch/arm/mach-socfpga/cyclone5-bootsource.c b/arch/arm/mach-socfpga/cyclone5-bootsource.c
index da4102c4f531..717a00342506 100644
--- a/arch/arm/mach-socfpga/cyclone5-bootsource.c
+++ b/arch/arm/mach-socfpga/cyclone5-bootsource.c
@@ -18,6 +18,7 @@
#include <io.h>
#include <mach/cyclone5-system-manager.h>
#include <mach/cyclone5-regs.h>
+#include <mach/arria10-system-manager.h>
#define CYCLONE5_SYSMGR_BOOTINFO 0x14
@@ -54,4 +55,46 @@ static int cyclone5_boot_save_loc(void)
return 0;
}
-core_initcall(cyclone5_boot_save_loc);
+
+static int arria10_boot_save_loc(void)
+{
+ enum bootsource src = BOOTSOURCE_UNKNOWN;
+ uint32_t val;
+
+ val = readl(ARRIA10_SYSMGR_BOOTINFO);
+
+ switch ((val & 0x7000) >> 12) {
+ case 0:
+ /* reserved */
+ break;
+ case 1:
+ /* FPGA, currently not decoded */
+ break;
+ case 2:
+ case 3:
+ src = BOOTSOURCE_NAND;
+ break;
+ case 4:
+ case 5:
+ src = BOOTSOURCE_MMC;
+ break;
+ case 6:
+ case 7:
+ src = BOOTSOURCE_SPI;
+ break;
+ }
+
+ bootsource_set(src);
+ bootsource_set_instance(0);
+
+ return 0;
+}
+
+static int socfpga_boot_save_loc(void)
+{
+ if (IS_ENABLED(CONFIG_ARCH_SOCFPGA_ARRIA10))
+ return arria10_boot_save_loc();
+ else
+ return cyclone5_boot_save_loc();
+}
+core_initcall(socfpga_boot_save_loc);
diff --git a/arch/arm/mach-socfpga/generic.c b/arch/arm/mach-socfpga/generic.c
deleted file mode 100644
index c920bd658fd7..000000000000
--- a/arch/arm/mach-socfpga/generic.c
+++ /dev/null
@@ -1,104 +0,0 @@
-#include <common.h>
-#include <malloc.h>
-#include <envfs.h>
-#include <init.h>
-#include <io.h>
-#include <fs.h>
-#include <linux/clkdev.h>
-#include <linux/clk.h>
-#include <linux/stat.h>
-#include <asm/memory.h>
-#include <mach/system-manager.h>
-#include <mach/reset-manager.h>
-#include <mach/socfpga-regs.h>
-#include <mach/nic301.h>
-
-#define SYSMGR_SDMMCGRP_CTRL_REG (CYCLONE5_SYSMGR_ADDRESS + 0x108)
-#define SYSMGR_SDMMC_CTRL_SMPLSEL(smplsel) (((smplsel) & 0x7) << 3)
-#define SYSMGR_SDMMC_CTRL_DRVSEL(drvsel) ((drvsel) & 0x7)
-
-static int socfpga_detect_sdram(void)
-{
- void __iomem *base = (void *)CYCLONE5_SDR_ADDRESS;
- uint32_t dramaddrw, ctrlwidth, memsize;
- int colbits, rowbits, bankbits;
- int width_bytes;
-
- dramaddrw = readl(base + 0x5000 + 0x2c);
-
- colbits = dramaddrw & 0x1f;
- rowbits = (dramaddrw >> 5) & 0x1f;
- bankbits = (dramaddrw >> 10) & 0x7;
-
- ctrlwidth = readl(base + 0x5000 + 0x60);
-
- switch (ctrlwidth & 0x3) {
- default:
- case 0:
- width_bytes = 1;
- break;
- case 1:
- width_bytes = 2;
- break;
- case 2:
- width_bytes = 4;
- break;
- }
-
- memsize = (1 << colbits) * (1 << rowbits) * (1 << bankbits) * width_bytes;
-
- pr_debug("%s: colbits: %d rowbits: %d bankbits: %d width: %d => memsize: 0x%08x\n",
- __func__, colbits, rowbits, bankbits, width_bytes, memsize);
-
- arm_add_mem_device("ram0", 0x0, memsize);
-
- return 0;
-}
-
-/* Some initialization for the EMAC */
-static void socfpga_init_emac(void)
-{
- uint32_t rst, val;
-
- /* No need for this without network support, e.g. xloader build */
- if (!IS_ENABLED(CONFIG_NET))
- return;
-
- /* According to Cyclone V datasheet, 17-60 "EMAC HPS Interface
- * Initialization", changing PHYSEL should be done with EMAC in reset
- * via permodrst. */
-
- /* Everything, except L4WD0/1, is out of reset via socfpga_lowlevel_init() */
- rst = readl(CYCLONE5_RSTMGR_ADDRESS + RESET_MGR_PER_MOD_RESET_OFS);
- rst |= RSTMGR_PERMODRST_EMAC0 | RSTMGR_PERMODRST_EMAC1;
- writel(rst, CYCLONE5_RSTMGR_ADDRESS + RESET_MGR_PER_MOD_RESET_OFS);
-
- /* Set emac0/1 PHY interface select to RGMII. We could read phy-mode
- * from the device tree, if it was desired to support interfaces other
- * than RGMII. */
- val = readl(CONFIG_SYSMGR_EMAC_CTRL);
- val &= ~(SYSMGR_EMACGRP_CTRL_PHYSEL_MASK << SYSMGR_EMACGRP_CTRL_PHYSEL0_LSB);
- val &= ~(SYSMGR_EMACGRP_CTRL_PHYSEL_MASK << SYSMGR_EMACGRP_CTRL_PHYSEL1_LSB);
- val |= SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_RGMII << SYSMGR_EMACGRP_CTRL_PHYSEL0_LSB;
- val |= SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_RGMII << SYSMGR_EMACGRP_CTRL_PHYSEL1_LSB;
- writel(val, CONFIG_SYSMGR_EMAC_CTRL);
-
- /* Take emac0 and emac1 out of reset */
- rst &= ~(RSTMGR_PERMODRST_EMAC0 | RSTMGR_PERMODRST_EMAC1);
- writel(rst, CYCLONE5_RSTMGR_ADDRESS + RESET_MGR_PER_MOD_RESET_OFS);
-}
-
-static int socfpga_init(void)
-{
- socfpga_init_emac();
-
- writel(SYSMGR_SDMMC_CTRL_DRVSEL(3) | SYSMGR_SDMMC_CTRL_SMPLSEL(0),
- SYSMGR_SDMMCGRP_CTRL_REG);
-
- nic301_slave_ns();
-
- socfpga_detect_sdram();
-
- return 0;
-}
-core_initcall(socfpga_init);
diff --git a/arch/arm/mach-socfpga/include/mach/arria10-clock-manager.h b/arch/arm/mach-socfpga/include/mach/arria10-clock-manager.h
new file mode 100644
index 000000000000..ee2b9b3c5ec1
--- /dev/null
+++ b/arch/arm/mach-socfpga/include/mach/arria10-clock-manager.h
@@ -0,0 +1,249 @@
+/*
+ * Copyright (C) 2014 Altera Corporation <www.altera.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _ARRIA10_CLOCK_MANAGER_H_
+#define _ARRIA10_CLOCK_MANAGER_H_
+
+struct arria10_clock_manager {
+ /* clkmgr */
+ volatile uint32_t ctrl;
+ volatile uint32_t intr;
+ volatile uint32_t intrs;
+ volatile uint32_t intrr;
+ volatile uint32_t intren;
+ volatile uint32_t intrens;
+ volatile uint32_t intrenr;
+ volatile uint32_t stat;
+ volatile uint32_t testioctrl;
+ volatile uint32_t _pad_0x24_0x40[7];
+
+ /* mainpllgrp*/
+ volatile uint32_t main_pll_vco0;
+ volatile uint32_t main_pll_vco1;
+ volatile uint32_t main_pll_en;
+ volatile uint32_t main_pll_ens;
+ volatile uint32_t main_pll_enr;
+ volatile uint32_t main_pll_bypass;
+ volatile uint32_t main_pll_bypasss;
+ volatile uint32_t main_pll_bypassr;
+ volatile uint32_t main_pll_mpuclk;
+ volatile uint32_t main_pll_nocclk;
+ volatile uint32_t main_pll_cntr2clk;
+ volatile uint32_t main_pll_cntr3clk;
+ volatile uint32_t main_pll_cntr4clk;
+ volatile uint32_t main_pll_cntr5clk;
+ volatile uint32_t main_pll_cntr6clk;
+ volatile uint32_t main_pll_cntr7clk;
+ volatile uint32_t main_pll_cntr8clk;
+ volatile uint32_t main_pll_cntr9clk;
+ volatile uint32_t main_pll__pad_0x48_0x5b[5];
+ volatile uint32_t main_pll_cntr15clk;
+ volatile uint32_t main_pll_outrst;
+ volatile uint32_t main_pll_outrststat;
+ volatile uint32_t main_pll_nocdiv;
+ volatile uint32_t main_pll__pad_0x6c_0x80[5];
+
+ /* perpllgrp*/
+ volatile uint32_t per_pll_vco0;
+ volatile uint32_t per_pll_vco1;
+ volatile uint32_t per_pll_en;
+ volatile uint32_t per_pll_ens;
+ volatile uint32_t per_pll_enr;
+ volatile uint32_t per_pll_bypass;
+ volatile uint32_t per_pll_bypasss;
+ volatile uint32_t per_pll_bypassr;
+ volatile uint32_t per_pll__pad_0x20_0x27[2];
+ volatile uint32_t per_pll_cntr2clk;
+ volatile uint32_t per_pll_cntr3clk;
+ volatile uint32_t per_pll_cntr4clk;
+ volatile uint32_t per_pll_cntr5clk;
+ volatile uint32_t per_pll_cntr6clk;
+ volatile uint32_t per_pll_cntr7clk;
+ volatile uint32_t per_pll_cntr8clk;
+ volatile uint32_t per_pll_cntr9clk;
+ volatile uint32_t per_pll__pad_0x48_0x5f[6];
+ volatile uint32_t per_pll_outrst;
+ volatile uint32_t per_pll_outrststat;
+ volatile uint32_t per_pll_emacctl;
+ volatile uint32_t per_pll_gpiodiv;
+ volatile uint32_t per_pll__pad_0x70_0x80[4];
+};
+
+struct arria10_mainpll_cfg {
+ uint32_t vco0_psrc;
+ uint32_t vco1_denom;
+ uint32_t vco1_numer;
+ uint32_t mpuclk;
+ uint32_t mpuclk_cnt;
+ uint32_t mpuclk_src;
+ uint32_t nocclk;
+ uint32_t nocclk_cnt;
+ uint32_t nocclk_src;
+ uint32_t cntr2clk_cnt;
+ uint32_t cntr3clk_cnt;
+ uint32_t cntr4clk_cnt;
+ uint32_t cntr5clk_cnt;
+ uint32_t cntr6clk_cnt;
+ uint32_t cntr7clk_cnt;
+ uint32_t cntr7clk_src;
+ uint32_t cntr8clk_cnt;
+ uint32_t cntr9clk_cnt;
+ uint32_t cntr9clk_src;
+ uint32_t cntr15clk_cnt;
+ uint32_t nocdiv_l4mainclk;
+ uint32_t nocdiv_l4mpclk;
+ uint32_t nocdiv_l4spclk;
+ uint32_t nocdiv_csatclk;
+ uint32_t nocdiv_cstraceclk;
+ uint32_t nocdiv_cspdbgclk;
+};
+
+struct arria10_perpll_cfg {
+ uint32_t vco0_psrc;
+ uint32_t vco1_denom;
+ uint32_t vco1_numer;
+ uint32_t cntr2clk_cnt;
+ uint32_t cntr2clk_src;
+ uint32_t cntr3clk_cnt;
+ uint32_t cntr3clk_src;
+ uint32_t cntr4clk_cnt;
+ uint32_t cntr4clk_src;
+ uint32_t cntr5clk_cnt;
+ uint32_t cntr5clk_src;
+ uint32_t cntr6clk_cnt;
+ uint32_t cntr6clk_src;
+ uint32_t cntr7clk_cnt;
+ uint32_t cntr8clk_cnt;
+ uint32_t cntr8clk_src;
+ uint32_t cntr9clk_cnt;
+ uint32_t cntr9clk_src;
+ uint32_t emacctl_emac0sel;
+ uint32_t emacctl_emac1sel;
+ uint32_t emacctl_emac2sel;
+ uint32_t gpiodiv_gpiodbclk;
+};
+
+extern int arria10_cm_basic_init(struct arria10_mainpll_cfg *mainpll_cfg,
+ struct arria10_perpll_cfg *perpll_cfg);
+extern unsigned int cm_get_mmc_controller_clk_hz(void);
+extern void arria10_cm_use_intosc(void);
+extern uint32_t cm_l4_main_clk_hz;
+extern uint32_t cm_l4_sp_clk_hz;
+extern uint32_t cm_l4_mp_clk_hz;
+extern uint32_t cm_l4_sys_free_clk_hz;
+
+#define ARRIA10_CLKMGR_ALTERAGRP_MPU_CLK_OFFSET 0x140
+#define ARRIA10_CLKMGR_MAINPLL_NOC_CLK_OFFSET 0x144
+
+/* value */
+#define ARRIA10_CLKMGR_MAINPLL_BYPASS_RESET 0x0000003f
+#define ARRIA10_CLKMGR_MAINPLL_VCO0_RESET 0x00010053
+#define ARRIA10_CLKMGR_MAINPLL_VCO1_RESET 0x00010001
+#define ARRIA10_CLKMGR_MAINPLL_VCO0_PSRC_EOSC 0x0
+#define ARRIA10_CLKMGR_MAINPLL_VCO0_PSRC_E_INTOSC 0x1
+#define ARRIA10_CLKMGR_MAINPLL_VCO0_PSRC_F2S 0x2
+#define ARRIA10_CLKMGR_PERPLL_BYPASS_RESET 0x000000ff
+#define ARRIA10_CLKMGR_PERPLL_VCO0_RESET 0x00010053
+#define ARRIA10_CLKMGR_PERPLL_VCO1_RESET 0x00010001
+#define ARRIA10_CLKMGR_PERPLL_VCO0_PSRC_EOSC 0x0
+#define ARRIA10_CLKMGR_PERPLL_VCO0_PSRC_E_INTOSC 0x1
+#define ARRIA10_CLKMGR_PERPLL_VCO0_PSRC_F2S 0x2
+#define ARRIA10_CLKMGR_PERPLL_VCO0_PSRC_MAIN 0x3
+
+/* mask */
+#define ARRIA10_CLKMGR_MAINPLL_EN_S2FUSER0CLKEN_SET_MSK 0x00000040
+#define ARRIA10_CLKMGR_MAINPLL_EN_HMCPLLREFCLKEN_SET_MSK 0x00000080
+#define ARRIA10_CLKMGR_MAINPLL_VCO0_BGPWRDN_SET_MSK 0x00000001
+#define ARRIA10_CLKMGR_MAINPLL_VCO0_PWRDN_SET_MSK 0x00000002
+#define ARRIA10_CLKMGR_MAINPLL_VCO0_EN_SET_MSK 0x00000004
+#define ARRIA10_CLKMGR_MAINPLL_VCO0_OUTRSTALL_SET_MSK 0x00000008
+#define ARRIA10_CLKMGR_MAINPLL_VCO0_REGEXTSEL_SET_MSK 0x00000010
+#define ARRIA10_CLKMGR_MAINPLL_VCO0_PSRC_MSK 0x00000003
+#define ARRIA10_CLKMGR_MAINPLL_VCO1_NUMER_MSK 0x00001fff
+#define ARRIA10_CLKMGR_MAINPLL_VCO1_DENOM_MSK 0x0000003f
+#define ARRIA10_CLKMGR_MAINPLL_CNTRCLK_MSK 0x000003ff
+#define ARRIA10_CLKMGR_MAINPLL_MPUCLK_CNT_MSK 0x000003ff
+#define ARRIA10_CLKMGR_MAINPLL_MPUCLK_SRC_MAIN 0
+#define ARRIA10_CLKMGR_MAINPLL_MPUCLK_SRC_PERI 1
+#define ARRIA10_CLKMGR_MAINPLL_MPUCLK_SRC_OSC1 2
+#define ARRIA10_CLKMGR_MAINPLL_MPUCLK_SRC_INTOSC 3
+#define ARRIA10_CLKMGR_MAINPLL_MPUCLK_SRC_FPGA 4
+#define ARRIA10_CLKMGR_MAINPLL_NOCDIV_MSK 0x00000003
+#define ARRIA10_CLKMGR_MAINPLL_NOCCLK_CNT_MSK 0x000003ff
+#define ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_MSK 0x00000007
+#define ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_MAIN 0
+#define ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_PERI 1
+#define ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_OSC1 2
+#define ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_INTOSC 3
+#define ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_FPGA 4
+#define ARRIA10_CLKMGR_CLKMGR_STAT_BUSY_SET_MSK 0x00000001
+#define ARRIA10_CLKMGR_CLKMGR_STAT_MAINPLLLOCKED_SET_MSK 0x00000100
+#define ARRIA10_CLKMGR_CLKMGR_STAT_PERPLLLOCKED_SET_MSK 0x00000200
+#define ARRIA10_CLKMGR_CLKMGR_STAT_BOOTCLKSRC_SET_MSK 0x00020000
+#define ARRIA10_CLKMGR_CLKMGR_INTR_PERPLLFBSLIP_SET_MSK 0x00000800
+#define ARRIA10_CLKMGR_CLKMGR_INTR_MAINPLLFBSLIP_SET_MSK 0x00000400
+#define ARRIA10_CLKMGR_CLKMGR_INTR_PERPLLRFSLIP_SET_MSK 0x00000200
+#define ARRIA10_CLKMGR_CLKMGR_INTR_MAINPLLRFSLIP_SET_MSK 0x00000100
+#define ARRIA10_CLKMGR_CLKMGR_INTR_PERPLLLOST_SET_MSK 0x00000008
+#define ARRIA10_CLKMGR_CLKMGR_INTR_MAINPLLLOST_SET_MSK 0x00000004
+#define ARRIA10_CLKMGR_CLKMGR_INTR_MAINPLLACHIEVED_SET_MSK 0x00000001
+#define ARRIA10_CLKMGR_CLKMGR_INTR_PERPLLACHIEVED_SET_MSK 0x00000002
+#define ARRIA10_CLKMGR_CLKMGR_CTL_BOOTMOD_SET_MSK 0x00000001
+#define ARRIA10_CLKMGR_CLKMGR_CTL_BOOTCLK_INTOSC_SET_MSK 0x00000300
+#define ARRIA10_CLKMGR_PERPLL_VCO0_BGPWRDN_SET_MSK 0x00000001
+#define ARRIA10_CLKMGR_PERPLL_VCO0_PWRDN_SET_MSK 0x00000002
+#define ARRIA10_CLKMGR_PERPLL_VCO0_EN_SET_MSK 0x00000004
+#define ARRIA10_CLKMGR_PERPLL_VCO0_OUTRSTALL_SET_MSK 0x00000008
+#define ARRIA10_CLKMGR_PERPLL_VCO0_REGEXTSEL_SET_MSK 0x00000010
+#define ARRIA10_CLKMGR_PERPLL_EN_RESET 0x00000f7f
+#define ARRIA10_CLKMGR_PERPLL_VCO0_PSRC_MSK 0x00000003
+#define ARRIA10_CLKMGR_PERPLL_VCO1_NUMER_MSK 0x00001fff
+#define ARRIA10_CLKMGR_PERPLL_VCO1_DENOM_MSK 0x0000003f
+#define ARRIA10_CLKMGR_PERPLL_CNTRCLK_MSK 0x000003ff
+
+#define ARRIA10_CLKMGR_PERPLLGRP_EN_SDMMCCLK_MASK 0x00000020
+#define ARRIA10_CLKMGR_PERPLLGRP_SRC_MSK 0x00000007
+#define ARRIA10_CLKMGR_PERPLLGRP_SRC_MAIN 0
+#define ARRIA10_CLKMGR_PERPLLGRP_SRC_PERI 1
+#define ARRIA10_CLKMGR_PERPLLGRP_SRC_OSC1 2
+#define ARRIA10_CLKMGR_PERPLLGRP_SRC_INTOSC 3
+#define ARRIA10_CLKMGR_PERPLLGRP_SRC_FPGA 4
+
+/* bit shifting macro */
+#define ARRIA10_CLKMGR_MAINPLL_VCO0_PSRC_LSB 8
+#define ARRIA10_CLKMGR_MAINPLL_VCO1_DENOM_LSB 16
+#define ARRIA10_CLKMGR_MAINPLL_NOCCLK_PERICNT_LSB 16
+#define ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_LSB 16
+#define ARRIA10_CLKMGR_MAINPLL_NOCDIV_L4MAINCLK_LSB 0
+#define ARRIA10_CLKMGR_MAINPLL_NOCDIV_L4MPCLK_LSB 8
+#define ARRIA10_CLKMGR_MAINPLL_NOCDIV_L4SPCLK_LSB 16
+#define ARRIA10_CLKMGR_MAINPLL_NOCDIV_CSATCLK_LSB 24
+#define ARRIA10_CLKMGR_MAINPLL_NOCDIV_CSTRACECLK_LSB 26
+#define ARRIA10_CLKMGR_MAINPLL_NOCDIV_CSPDBGCLK_LSB 28
+#define ARRIA10_CLKMGR_MAINPLL_MPUCLK_SRC_LSB 16
+#define ARRIA10_CLKMGR_MAINPLL_MPUCLK_PERICNT_LSB 16
+#define ARRIA10_CLKMGR_MAINPLL_NOCCLK_SRC_LSB 16
+#define ARRIA10_CLKMGR_MAINPLL_CNTR7CLK_SRC_LSB 16
+#define ARRIA10_CLKMGR_MAINPLL_CNTR9CLK_SRC_LSB 16
+#define ARRIA10_CLKMGR_PERPLL_VCO1_DENOM_LSB 16
+#define ARRIA10_CLKMGR_PERPLL_VCO0_PSRC_LSB 8
+#define ARRIA10_CLKMGR_PERPLL_CNTR2CLK_SRC_LSB 16
+#define ARRIA10_CLKMGR_PERPLL_CNTR3CLK_SRC_LSB 16
+#define ARRIA10_CLKMGR_PERPLL_CNTR4CLK_SRC_LSB 16
+#define ARRIA10_CLKMGR_PERPLL_CNTR5CLK_SRC_LSB 16
+#define ARRIA10_CLKMGR_PERPLL_CNTR6CLK_SRC_LSB 16
+#define ARRIA10_CLKMGR_PERPLL_CNTR8CLK_SRC_LSB 16
+#define ARRIA10_CLKMGR_PERPLL_EMACCTL_EMAC0SEL_LSB 26
+#define ARRIA10_CLKMGR_PERPLL_EMACCTL_EMAC1SEL_LSB 27
+#define ARRIA10_CLKMGR_PERPLL_EMACCTL_EMAC2SEL_LSB 28
+
+/* PLL ramping work around */
+#define ARRIA10_CLKMGR_PLL_RAMP_MPUCLK_THRESHOLD_HZ 900000000
+#define ARRIA10_CLKMGR_PLL_RAMP_NOCCLK_THRESHOLD_HZ 300000000
+#define ARRIA10_CLKMGR_PLL_RAMP_MPUCLK_INCREMENT_HZ 100000000
+#define ARRIA10_CLKMGR_PLL_RAMP_NOCCLK_INCREMENT_HZ 33000000
+
+#endif /* _ARRIA10_CLOCK_MANAGER_H_ */
diff --git a/arch/arm/mach-socfpga/include/mach/arria10-pinmux.h b/arch/arm/mach-socfpga/include/mach/arria10-pinmux.h
new file mode 100644
index 000000000000..804fae0309be
--- /dev/null
+++ b/arch/arm/mach-socfpga/include/mach/arria10-pinmux.h
@@ -0,0 +1,128 @@
+/*
+ * Copyright (C) 2017 Pengutronix, Steffen Trumtrar <kernel@pengutronix.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef _ARRIA10_PINMUX_H_
+#define _ARRIA10_PINMUX_H_
+
+struct arria10_pinmux_cfg {
+ uint32_t shared_io_q1_1;
+ uint32_t shared_io_q1_2;
+ uint32_t shared_io_q1_3;
+ uint32_t shared_io_q1_4;
+ uint32_t shared_io_q1_5;
+ uint32_t shared_io_q1_6;
+ uint32_t shared_io_q1_7;
+ uint32_t shared_io_q1_8;
+ uint32_t shared_io_q1_9;
+ uint32_t shared_io_q1_10;
+ uint32_t shared_io_q1_11;
+ uint32_t shared_io_q1_12;
+
+ uint32_t shared_io_q2_1;
+ uint32_t shared_io_q2_2;
+ uint32_t shared_io_q2_3;
+ uint32_t shared_io_q2_4;
+ uint32_t shared_io_q2_5;
+ uint32_t shared_io_q2_6;
+ uint32_t shared_io_q2_7;
+ uint32_t shared_io_q2_8;
+ uint32_t shared_io_q2_9;
+ uint32_t shared_io_q2_10;
+ uint32_t shared_io_q2_11;
+ uint32_t shared_io_q2_12;
+
+ uint32_t shared_io_q3_1;
+ uint32_t shared_io_q3_2;
+ uint32_t shared_io_q3_3;
+ uint32_t shared_io_q3_4;
+ uint32_t shared_io_q3_5;
+ uint32_t shared_io_q3_6;
+ uint32_t shared_io_q3_7;
+ uint32_t shared_io_q3_8;
+ uint32_t shared_io_q3_9;
+ uint32_t shared_io_q3_10;
+ uint32_t shared_io_q3_11;
+ uint32_t shared_io_q3_12;
+
+ uint32_t shared_io_q4_1;
+ uint32_t shared_io_q4_2;
+ uint32_t shared_io_q4_3;
+ uint32_t shared_io_q4_4;
+ uint32_t shared_io_q4_5;
+ uint32_t shared_io_q4_6;
+ uint32_t shared_io_q4_7;
+ uint32_t shared_io_q4_8;
+ uint32_t shared_io_q4_9;
+ uint32_t shared_io_q4_10;
+ uint32_t shared_io_q4_11;
+ uint32_t shared_io_q4_12;
+
+ uint32_t dedicated_io_4;
+ uint32_t dedicated_io_5;
+ uint32_t dedicated_io_6;
+ uint32_t dedicated_io_7;
+ uint32_t dedicated_io_8;
+ uint32_t dedicated_io_9;
+ uint32_t dedicated_io_10;
+ uint32_t dedicated_io_11;
+ uint32_t dedicated_io_12;
+ uint32_t dedicated_io_13;
+ uint32_t dedicated_io_14;
+ uint32_t dedicated_io_15;
+ uint32_t dedicated_io_16;
+ uint32_t dedicated_io_17;
+
+ uint32_t cfg_dedicated_io_bank;
+ uint32_t cfg_dedicated_io_1;
+ uint32_t cfg_dedicated_io_2;
+ uint32_t cfg_dedicated_io_3;
+ uint32_t cfg_dedicated_io_4;
+ uint32_t cfg_dedicated_io_5;
+ uint32_t cfg_dedicated_io_6;
+ uint32_t cfg_dedicated_io_7;
+ uint32_t cfg_dedicated_io_8;
+ uint32_t cfg_dedicated_io_9;
+ uint32_t cfg_dedicated_io_10;
+ uint32_t cfg_dedicated_io_11;
+ uint32_t cfg_dedicated_io_12;
+ uint32_t cfg_dedicated_io_13;
+ uint32_t cfg_dedicated_io_14;
+ uint32_t cfg_dedicated_io_15;
+ uint32_t cfg_dedicated_io_16;
+ uint32_t cfg_dedicated_io_17;
+
+ bool rgmii0_usefpga;
+ bool rgmii1_usefpga;
+ bool rgmii2_usefpga;
+ bool nand_usefpga;
+ bool qspi_usefpga;
+ bool sdmmc_usefpga;
+ bool usb0_usefpga;
+ bool usb1_usefpga;
+ bool spim0_usefpga;
+ bool spim1_usefpga;
+ bool spis0_usefpga;
+ bool spis1_usefpga;
+ bool uart0_usefpga;
+ bool uart1_usefpga;
+ bool i2c0_usefpga;
+ bool i2c1_usefpga;
+ bool i2cemac0_usefpga;
+ bool i2cemac1_usefpga;
+ bool i2cemac2_usefpga;
+ bool pll_clock_out_usefpga;
+};
+
+#endif
diff --git a/arch/arm/mach-socfpga/include/mach/arria10-regs.h b/arch/arm/mach-socfpga/include/mach/arria10-regs.h
new file mode 100644
index 000000000000..44a3f69c24c9
--- /dev/null
+++ b/arch/arm/mach-socfpga/include/mach/arria10-regs.h
@@ -0,0 +1,114 @@
+/*
+ * Copyright (C) 2014 Altera Corporation <www.altera.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _ARRIA10_HARDWARE_H_
+#define _ARRIA10_HARDWARE_H_
+
+#define ARRIA10_EMAC0_ADDR (0xff800000)
+#define ARRIA10_EMAC1_ADDR (0xff802000)
+#define ARRIA10_EMAC2_ADDR (0xff804000)
+#define ARRIA10_SDMMC_ADDR (0xff808000)
+#define ARRIA10_QSPIREGS_ADDR (0xff809000)
+#define ARRIA10_ECC_OCRAM_ADDR (0xff8c3000)
+#define ARRIA10_QSPIDATA_ADDR (0xffa00000)
+#define ARRIA10_UART0_ADDR (0xffc02000)
+#define ARRIA10_UART1_ADDR (0xffc02100)
+#define ARRIA10_I2C0_ADDR (0xffc02200)
+#define ARRIA10_I2C1_ADDR (0xffc02300)
+#define ARRIA10_GPIO0_ADDR (0xffc02900)
+#define ARRIA10_GPIO1_ADDR (0xffc02a00)
+#define ARRIA10_GPIO2_ADDR (0xffc02b00)
+#define ARRIA10_HMC_MMR_IO48_ADDR (0xffcfa000)
+#define ARRIA10_SDR_ADDR (0xffcfb000)
+#define ARRIA10_FPGAMGRDATA_ADDR (0xffcfe400)
+#define ARRIA10_OSC1TIMER0_ADDR (0xffd00000)
+#define ARRIA10_L4WD0_ADDR (0xffd00200)
+#define ARRIA10_FPGAMGRREGS_ADDR (0xffd03000)
+#define ARRIA10_CLKMGR_ADDR (0xffd04000)
+#define ARRIA10_RSTMGR_ADDR (0xffd05000)
+#define ARRIA10_SYSMGR_ADDR (0xffd06000)
+#define ARRIA10_PINMUX_SHARED_3V_IO_ADDR (0xffd07000)
+#define ARRIA10_PINMUX_DEDICATED_IO_ADDR (0xffd07200)
+#define ARRIA10_PINMUX_DEDICATED_IO_CFG_ADDR (0xffd07300)
+#define ARRIA10_PINMUX_FPGA_INTERFACE_ADDR (0xffd07400)
+#define ARRIA10_NOC_L4_PRIV_L4_PRIV_FILTER_ADDR (0xffd11000)
+#define ARRIA10_SDR_SCHEDULER_ADDR (0xffd12400)
+#define ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR (0xffd13000)
+#define ARRIA10_NOC_FW_OCRAM_OCRAM_SCR_ADDR (0xffd13200)
+#define ARRIA10_SDR_FW_MPU_FPGA_ADDR (0xffd13300)
+#define ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR (0xffd13400)
+#define ARRIA10_NOC_FW_SOC2FPGA_SOC2FPGA_SCR_ADDR (0xffd13500)
+#define ARRIA10_DMANONSECURE_ADDR (0xffda0000)
+#define ARRIA10_DMASECURE_ADDR (0xffda1000)
+#define ARRIA10_MPUSCU_ADDR (0xffffc000)
+#define ARRIA10_MPUL2_ADDR (0xfffff000)
+
+/* L2 cache controller */
+#define ARRIA10_MPUL2_ADRFLTR_START (ARRIA10_MPUL2_ADDR + 0xC00)
+
+/* NOC L4 Priv */
+#define ARRIA10_NOC_L4_PRIV_L4_PRIV_L4_PRIV (ARRIA10_NOC_L4_PRIV_L4_PRIV_FILTER_ADDR + 0x00)
+#define ARRIA10_NOC_L4_PRIV_L4_PRIV_L4_PRIV_SET (ARRIA10_NOC_L4_PRIV_L4_PRIV_FILTER_ADDR + 0x04)
+#define ARRIA10_NOC_L4_PRIV_L4_PRIV_L4_PRIV_CLR (ARRIA10_NOC_L4_PRIV_L4_PRIV_FILTER_ADDR + 0x08)
+
+/* NOC L4 Permissions */
+#define ARRIA10_NOC_FW_L4_PER_SCR_NAND_REG (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x00)
+#define ARRIA10_NOC_FW_L4_PER_SCR_NAND_DATA (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x04)
+#define ARRIA10_NOC_FW_L4_PER_SCR_QSPI_DATA (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x08)
+#define ARRIA10_NOC_FW_L4_PER_SCR_USB0_REG (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x0c)
+#define ARRIA10_NOC_FW_L4_PER_SCR_USB1_REG (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x10)
+#define ARRIA10_NOC_FW_L4_PER_SCR_DMA_NONSECURE (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x14)
+#define ARRIA10_NOC_FW_L4_PER_SCR_DMA_SECURE (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x18)
+#define ARRIA10_NOC_FW_L4_PER_SCR_SPIM0 (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x1c)
+#define ARRIA10_NOC_FW_L4_PER_SCR_SPIM1 (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x20)
+#define ARRIA10_NOC_FW_L4_PER_SCR_SPIS0 (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x24)
+#define ARRIA10_NOC_FW_L4_PER_SCR_SPIS1 (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x28)
+#define ARRIA10_NOC_FW_L4_PER_SCR_EMAC0 (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x2c)
+#define ARRIA10_NOC_FW_L4_PER_SCR_EMAC1 (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x30)
+#define ARRIA10_NOC_FW_L4_PER_SCR_EMAC2 (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x34)
+#define ARRIA10_NOC_FW_L4_PER_SCR_EMAC3 (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x38)
+#define ARRIA10_NOC_FW_L4_PER_SCR_QSPI (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x3c)
+#define ARRIA10_NOC_FW_L4_PER_SCR_SDMMC (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x40)
+#define ARRIA10_NOC_FW_L4_PER_SCR_GPIO0 (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x44)
+#define ARRIA10_NOC_FW_L4_PER_SCR_GPIO1 (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x48)
+#define ARRIA10_NOC_FW_L4_PER_SCR_GPIO2 (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x4c)
+#define ARRIA10_NOC_FW_L4_PER_SCR_I2C0 (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x50)
+#define ARRIA10_NOC_FW_L4_PER_SCR_I2C1 (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x54)
+#define ARRIA10_NOC_FW_L4_PER_SCR_I2C2 (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x58)
+#define ARRIA10_NOC_FW_L4_PER_SCR_I2C3 (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x5c)
+#define ARRIA10_NOC_FW_L4_PER_SCR_I2C4 (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x60)
+#define ARRIA10_NOC_FW_L4_PER_SCR_SPTIMER0 (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x64)
+#define ARRIA10_NOC_FW_L4_PER_SCR_SPTIMER1 (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x68)
+#define ARRIA10_NOC_FW_L4_PER_SCR_UART0 (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x6c)
+#define ARRIA10_NOC_FW_L4_PER_SCR_UART1 (ARRIA10_NOC_L4_PER_L4_PER_SCR_ADDR + 0x70)
+
+#define ARRIA10_NOC_FW_OCRAM_OCRAM_SCR_EN (ARRIA10_NOC_FW_OCRAM_OCRAM_SCR_ADDR + 0x00)
+#define ARRIA10_NOC_FW_OCRAM_OCRAM_SCR_EN_SET (ARRIA10_NOC_FW_OCRAM_OCRAM_SCR_ADDR + 0x04)
+#define ARRIA10_NOC_FW_OCRAM_OCRAM_SCR_EN_CLR (ARRIA10_NOC_FW_OCRAM_OCRAM_SCR_ADDR + 0x08)
+#define ARRIA10_NOC_FW_OCRAM_OCRAM_SCR_REGION0 (ARRIA10_NOC_FW_OCRAM_OCRAM_SCR_ADDR + 0x0c)
+#define ARRIA10_NOC_FW_OCRAM_OCRAM_SCR_REGION1 (ARRIA10_NOC_FW_OCRAM_OCRAM_SCR_ADDR + 0x10)
+#define ARRIA10_NOC_FW_OCRAM_OCRAM_SCR_REGION2 (ARRIA10_NOC_FW_OCRAM_OCRAM_SCR_ADDR + 0x14)
+#define ARRIA10_NOC_FW_OCRAM_OCRAM_SCR_REGION3 (ARRIA10_NOC_FW_OCRAM_OCRAM_SCR_ADDR + 0x18)
+#define ARRIA10_NOC_FW_OCRAM_OCRAM_SCR_REGION4 (ARRIA10_NOC_FW_OCRAM_OCRAM_SCR_ADDR + 0x1c)
+#define ARRIA10_NOC_FW_OCRAM_OCRAM_SCR_REGION5 (ARRIA10_NOC_FW_OCRAM_OCRAM_SCR_ADDR + 0x20)
+
+#define ARRIA10_NOC_FW_DDR_L3_DDR_SCR_EN (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x00)
+#define ARRIA10_NOC_FW_DDR_L3_DDR_SCR_EN_SET (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x04)
+#define ARRIA10_NOC_FW_DDR_L3_DDR_SCR_EN_CLR (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x08)
+#define ARRIA10_NOC_FW_DDR_L3_DDR_SCR_REGION0 (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x0c)
+#define ARRIA10_NOC_FW_DDR_L3_DDR_SCR_REGION1 (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x10)
+#define ARRIA10_NOC_FW_DDR_L3_DDR_SCR_REGION2 (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x14)
+#define ARRIA10_NOC_FW_DDR_L3_DDR_SCR_REGION3 (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x18)
+#define ARRIA10_NOC_FW_DDR_L3_DDR_SCR_REGION4 (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x1c)
+#define ARRIA10_NOC_FW_DDR_L3_DDR_SCR_REGION5 (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x20)
+#define ARRIA10_NOC_FW_DDR_L3_DDR_SCR_REGION6 (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x24)
+#define ARRIA10_NOC_FW_DDR_L3_DDR_SCR_REGION7 (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x28)
+#define ARRIA10_NOC_FW_DDR_L3_DDR_SCR_GLOBAL (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x2c)
+
+#define ARRIA10_NOC_FW_SOC2FPGA_SOC2FPGA_SCR_LWSOC2FPGA (ARRIA10_NOC_FW_SOC2FPGA_SOC2FPGA_SCR_ADDR + 0x00)
+#define ARRIA10_NOC_FW_SOC2FPGA_SOC2FPGA_SCR_SOC2FPGA (ARRIA10_NOC_FW_SOC2FPGA_SOC2FPGA_SCR_ADDR + 0x04)
+
+#endif
diff --git a/arch/arm/mach-socfpga/include/mach/arria10-reset-manager.h b/arch/arm/mach-socfpga/include/mach/arria10-reset-manager.h
new file mode 100644
index 000000000000..9814d18d5547
--- /dev/null
+++ b/arch/arm/mach-socfpga/include/mach/arria10-reset-manager.h
@@ -0,0 +1,119 @@
+/*
+ * Copyright (C) 2014-2016 Altera Corporation <www.altera.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+#ifndef _ARRIA10_RESET_MANAGER_H_
+#define _ARRIA10_RESET_MANAGER_H_
+
+#define ARRIA10_RSTMGR_STATUS 0x0
+#define ARRIA10_RSTMGR_RAMSTAT 0x4
+#define ARRIA10_RSTMGR_MISCSTAT 0x8
+#define ARRIA10_RSTMGR_CTRL 0xc
+#define ARRIA10_RSTMGR_HDSKEN 0x10
+#define ARRIA10_RSTMGR_HDSKREQ 0x14
+#define ARRIA10_RSTMGR_HDSKACK 0x18
+#define ARRIA10_RSTMGR_COUNTS 0x1c
+#define ARRIA10_RSTMGR_MPUMODRST 0x20
+#define ARRIA10_RSTMGR_PER0MODRST 0x24
+#define ARRIA10_RSTMGR_PER1MODRST 0x28
+#define ARRIA10_RSTMGR_BRGMODRST 0x2c
+#define ARRIA10_RSTMGR_SYSMODRST 0x30
+#define ARRIA10_RSTMGR_COLDMODRST 0x34
+#define ARRIA10_RSTMGR_NRSTMODRST 0x38
+#define ARRIA10_RSTMGR_DBGMODRST 0x3c
+#define ARRIA10_RSTMGR_MPUWARMMASK 0x40
+#define ARRIA10_RSTMGR_PER0WARMMASK 0x44
+#define ARRIA10_RSTMGR_PER1WARMMASK 0x48
+#define ARRIA10_RSTMGR_BRGWARMMASK 0x4c
+#define ARRIA10_RSTMGR_SYSWARMMASK 0x50
+#define ARRIA10_RSTMGR_NRSTWARMMASK 0x54
+#define ARRIA10_RSTMGR_L3WARMMASK 0x58
+#define ARRIA10_RSTMGR_TSTSTA 0x5c
+#define ARRIA10_RSTMGR_TSTSCRATCH 0x60
+#define ARRIA10_RSTMGR_HDSKTIMEOUT 0x64
+#define ARRIA10_RSTMGR_HMCINTR 0x68
+#define ARRIA10_RSTMGR_HMCINTREN 0x6c
+#define ARRIA10_RSTMGR_HMCINTRENS 0x70
+#define ARRIA10_RSTMGR_HMCINTRENR 0x74
+#define ARRIA10_RSTMGR_HMCGPOUT 0x78
+#define ARRIA10_RSTMGR_HMCGPIN 0x7c
+
+#define ARRIA10_RSTMGR_CTL_SWWARMRSTREQ 0x00000002
+#define ARRIA10_RSTMGR_PER0MODRST_EMAC0 0x00000001
+#define ARRIA10_RSTMGR_PER0MODRST_EMAC1 0x00000002
+#define ARRIA10_RSTMGR_PER0MODRST_EMAC2 0x00000004
+#define ARRIA10_RSTMGR_PER0MODRST_USB0 0x00000008
+#define ARRIA10_RSTMGR_PER0MODRST_USB1 0x00000010
+#define ARRIA10_RSTMGR_PER0MODRST_NAND 0x00000020
+#define ARRIA10_RSTMGR_PER0MODRST_QSPI 0x00000040
+#define ARRIA10_RSTMGR_PER0MODRST_SDMMC 0x00000080
+#define ARRIA10_RSTMGR_PER0MODRST_EMACECC0 0x00000100
+#define ARRIA10_RSTMGR_PER0MODRST_EMACECC1 0x00000200
+#define ARRIA10_RSTMGR_PER0MODRST_EMACECC2 0x00000400
+#define ARRIA10_RSTMGR_PER0MODRST_USBECC0 0x00000800
+#define ARRIA10_RSTMGR_PER0MODRST_USBECC1 0x00001000
+#define ARRIA10_RSTMGR_PER0MODRST_NANDECC 0x00002000
+#define ARRIA10_RSTMGR_PER0MODRST_QSPIECC 0x00004000
+#define ARRIA10_RSTMGR_PER0MODRST_SDMMCECC 0x00008000
+#define ARRIA10_RSTMGR_PER0MODRST_DMA 0x00010000
+#define ARRIA10_RSTMGR_PER0MODRST_SPIM0 0x00020000
+#define ARRIA10_RSTMGR_PER0MODRST_SPIM1 0x00040000
+#define ARRIA10_RSTMGR_PER0MODRST_SPIS0 0x00080000
+#define ARRIA10_RSTMGR_PER0MODRST_SPIS1 0x00100000
+#define ARRIA10_RSTMGR_PER0MODRST_DMAECC 0x00200000
+#define ARRIA10_RSTMGR_PER0MODRST_EMACPTP 0x00400000
+#define ARRIA10_RSTMGR_PER0MODRST_DMAIF0 0x01000000
+#define ARRIA10_RSTMGR_PER0MODRST_DMAIF1 0x02000000
+#define ARRIA10_RSTMGR_PER0MODRST_DMAIF2 0x04000000
+#define ARRIA10_RSTMGR_PER0MODRST_DMAIF3 0x08000000
+#define ARRIA10_RSTMGR_PER0MODRST_DMAIF4 0x10000000
+#define ARRIA10_RSTMGR_PER0MODRST_DMAIF5 0x20000000
+#define ARRIA10_RSTMGR_PER0MODRST_DMAIF6 0x40000000
+#define ARRIA10_RSTMGR_PER0MODRST_DMAIF7 0x80000000
+
+#define ARRIA10_RSTMGR_PER1MODRST_L4WD0 0x00000001
+#define ARRIA10_RSTMGR_PER1MODRST_L4WD1 0x00000002
+#define ARRIA10_RSTMGR_PER1MODRST_L4SYSTMR0 0x00000004
+#define ARRIA10_RSTMGR_PER1MODRST_L4SYSTMR1 0x00000008
+#define ARRIA10_RSTMGR_PER1MODRST_SPTMR0 0x00000010
+#define ARRIA10_RSTMGR_PER1MODRST_SPTMR1 0x00000020
+#define ARRIA10_RSTMGR_PER1MODRST_I2C0 0x00000100
+#define ARRIA10_RSTMGR_PER1MODRST_I2C1 0x00000200
+#define ARRIA10_RSTMGR_PER1MODRST_I2C2 0x00000400
+#define ARRIA10_RSTMGR_PER1MODRST_I2C3 0x00000800
+#define ARRIA10_RSTMGR_PER1MODRST_I2C4 0x00001000
+#define ARRIA10_RSTMGR_PER1MODRST_UART0 0x00010000
+#define ARRIA10_RSTMGR_PER1MODRST_UART1 0x00020000
+#define ARRIA10_RSTMGR_PER1MODRST_GPIO0 0x01000000
+#define ARRIA10_RSTMGR_PER1MODRST_GPIO1 0x02000000
+#define ARRIA10_RSTMGR_PER1MODRST_GPIO2 0x04000000
+
+#define ARRIA10_RSTMGR_BRGMODRST_H2F 0x00000001
+#define ARRIA10_RSTMGR_BRGMODRST_LWH2F 0x00000002
+#define ARRIA10_RSTMGR_BRGMODRST_F2H 0x00000004
+#define ARRIA10_RSTMGR_BRGMODRST_F2SSDRAM0 0x00000008
+#define ARRIA10_RSTMGR_BRGMODRST_F2SSDRAM1 0x00000010
+#define ARRIA10_RSTMGR_BRGMODRST_F2SSDRAM2 0x00000020
+#define ARRIA10_RSTMGR_BRGMODRST_DDRSCH 0x00000040
+
+#define ARRIA10_RSTMGR_HDSKEN_SDRSELFREFEN 0x00000001
+#define ARRIA10_RSTMGR_HDSKEN_FPGAMGRHSEN 0x00000002
+#define ARRIA10_RSTMGR_HDSKEN_FPGAHSEN 0x00000004
+#define ARRIA10_RSTMGR_HDSKEN_ETRSTALLEN 0x00000008
+
+#define ECC_MASK (ARRIA10_RSTMGR_PER0MODRST_EMACECC0 | \
+ ARRIA10_RSTMGR_PER0MODRST_EMACECC1 | \
+ ARRIA10_RSTMGR_PER0MODRST_EMACECC2 | \
+ ARRIA10_RSTMGR_PER0MODRST_NANDECC | \
+ ARRIA10_RSTMGR_PER0MODRST_QSPIECC | \
+ ARRIA10_RSTMGR_PER0MODRST_SDMMCECC)
+
+void arria10_reset_peripherals(void);
+void arria10_reset_deassert_dedicated_peripherals(void);
+void arria10_reset_deassert_shared_peripherals(void);
+void arria10_reset_deassert_fpga_peripherals(void);
+
+#endif
+
diff --git a/arch/arm/mach-socfpga/include/mach/arria10-sdram.h b/arch/arm/mach-socfpga/include/mach/arria10-sdram.h
new file mode 100644
index 000000000000..07e4dd013089
--- /dev/null
+++ b/arch/arm/mach-socfpga/include/mach/arria10-sdram.h
@@ -0,0 +1,353 @@
+/*
+ * Copyright (C) 2014 Altera Corporation <www.altera.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+#include <mach/arria10-system-manager.h>
+
+#ifndef _ARRIA10_SDRAM_H_
+#define _ARRIA10_SDRAM_H_
+
+#define ARRIA10_ECC_HMC_OCP_IP_REV_ID (ARRIA10_SDR_ADDR + 0x00)
+#define ARRIA10_ECC_HMC_OCP_DDRIOCTRL (ARRIA10_SDR_ADDR + 0x08)
+#define ARRIA10_ECC_HMC_OCP_DDRCALSTAT (ARRIA10_SDR_ADDR + 0x0c)
+#define ARRIA10_ECC_HMC_OCP_MPR_OBEAT1 (ARRIA10_SDR_ADDR + 0x10)
+#define ARRIA10_ECC_HMC_OCP_MPR_1BEAT1 (ARRIA10_SDR_ADDR + 0x14)
+#define ARRIA10_ECC_HMC_OCP_MPR_2BEAT1 (ARRIA10_SDR_ADDR + 0x18)
+#define ARRIA10_ECC_HMC_OCP_MPR_3BEAT1 (ARRIA10_SDR_ADDR + 0x1c)
+#define ARRIA10_ECC_HMC_OCP_MPR_4BEAT1 (ARRIA10_SDR_ADDR + 0x20)
+#define ARRIA10_ECC_HMC_OCP_MPR_5BEAT1 (ARRIA10_SDR_ADDR + 0x24)
+#define ARRIA10_ECC_HMC_OCP_MPR_6BEAT1 (ARRIA10_SDR_ADDR + 0x28)
+#define ARRIA10_ECC_HMC_OCP_MPR_7BEAT1 (ARRIA10_SDR_ADDR + 0x2c)
+#define ARRIA10_ECC_HMC_OCP_MPR_8BEAT1 (ARRIA10_SDR_ADDR + 0x30)
+#define ARRIA10_ECC_HMC_OCP_MPR_OBEAT2 (ARRIA10_SDR_ADDR + 0x34)
+#define ARRIA10_ECC_HMC_OCP_MPR_1BEAT2 (ARRIA10_SDR_ADDR + 0x38)
+#define ARRIA10_ECC_HMC_OCP_MPR_2BEAT2 (ARRIA10_SDR_ADDR + 0x3c)
+#define ARRIA10_ECC_HMC_OCP_MPR_3BEAT2 (ARRIA10_SDR_ADDR + 0x40)
+#define ARRIA10_ECC_HMC_OCP_MPR_4BEAT2 (ARRIA10_SDR_ADDR + 0x44)
+#define ARRIA10_ECC_HMC_OCP_MPR_5BEAT2 (ARRIA10_SDR_ADDR + 0x48)
+#define ARRIA10_ECC_HMC_OCP_MPR_6BEAT2 (ARRIA10_SDR_ADDR + 0x4c)
+#define ARRIA10_ECC_HMC_OCP_MPR_7BEAT2 (ARRIA10_SDR_ADDR + 0x50)
+#define ARRIA10_ECC_HMC_OCP_MPR_8BEAT2 (ARRIA10_SDR_ADDR + 0x54)
+#define ARRIA10_ECC_HMC_OCP_MPR_AUTO_PRECHARGE (ARRIA10_SDR_ADDR + 0x60)
+#define ARRIA10_ECC_HMC_OCP_MPR_ECCCTRL1 (ARRIA10_SDR_ADDR + 0x100)
+#define ARRIA10_ECC_HMC_OCP_MPR_ECCCTRL2 (ARRIA10_SDR_ADDR + 0x104)
+#define ARRIA10_ECC_HMC_OCP_MPR_ERRINTEN (ARRIA10_SDR_ADDR + 0x110)
+#define ARRIA10_ECC_HMC_OCP_MPR_ERRINTENS (ARRIA10_SDR_ADDR + 0x114)
+#define ARRIA10_ECC_HMC_OCP_MPR_ERRINTENR (ARRIA10_SDR_ADDR + 0x118)
+#define ARRIA10_ECC_HMC_OCP_MPR_INTMODE (ARRIA10_SDR_ADDR + 0x11c)
+#define ARRIA10_ECC_HMC_OCP_MPR_INTSTAT (ARRIA10_SDR_ADDR + 0x120)
+#define ARRIA10_ECC_HMC_OCP_MPR_DIAGINTTEST (ARRIA10_SDR_ADDR + 0x124)
+#define ARRIA10_ECC_HMC_OCP_MPR_MODSTAT (ARRIA10_SDR_ADDR + 0x128)
+#define ARRIA10_ECC_HMC_OCP_MPR_DERRADDRA (ARRIA10_SDR_ADDR + 0x12c)
+#define ARRIA10_ECC_HMC_OCP_MPR_SERRADDRA (ARRIA10_SDR_ADDR + 0x130)
+#define ARRIA10_ECC_HMC_OCP_MPR_AUTOWB_CORRADDR (ARRIA10_SDR_ADDR + 0x138)
+#define ARRIA10_ECC_HMC_OCP_MPR_SERRCNTREG (ARRIA10_SDR_ADDR + 0x13c)
+#define ARRIA10_ECC_HMC_OCP_MPR_AUTOWB_DROP_CNTREG (ARRIA10_SDR_ADDR + 0x140)
+#define ARRIA10_ECC_HMC_OCP_MPR_ECC_REG2WRECCDATABUS (ARRIA10_SDR_ADDR + 0x144)
+#define ARRIA10_ECC_HMC_OCP_MPR_ECC_RDECCDATA2REGBUS (ARRIA10_SDR_ADDR + 0x148)
+#define ARRIA10_ECC_HMC_OCP_MPR_ECC_REG2RDECCDATABUS (ARRIA10_SDR_ADDR + 0x14c)
+#define ARRIA10_ECC_HMC_OCP_MPR_ECC_DIAGON (ARRIA10_SDR_ADDR + 0x150)
+#define ARRIA10_ECC_HMC_OCP_MPR_ECC_DECSTAT (ARRIA10_SDR_ADDR + 0x154)
+#define ARRIA10_ECC_HMC_OCP_MPR_ECC_ERRGENADDR_0 (ARRIA10_SDR_ADDR + 0x160)
+#define ARRIA10_ECC_HMC_OCP_MPR_ECC_ERRGENADDR_1 (ARRIA10_SDR_ADDR + 0x164)
+#define ARRIA10_ECC_HMC_OCP_MPR_ECC_ERRGENADDR_2 (ARRIA10_SDR_ADDR + 0x168)
+#define ARRIA10_ECC_HMC_OCP_MPR_ECC_ERRGENADDR_3 (ARRIA10_SDR_ADDR + 0x16c)
+#define ARRIA10_ECC_HMC_OCP_MPR_ECC_REG2RDDATABUS_BEAT0 (ARRIA10_SDR_ADDR + 0x170)
+#define ARRIA10_ECC_HMC_OCP_MPR_ECC_REG2RDDATABUS_BEAT1 (ARRIA10_SDR_ADDR + 0x174)
+#define ARRIA10_ECC_HMC_OCP_MPR_ECC_REG2RDDATABUS_BEAT2 (ARRIA10_SDR_ADDR + 0x178)
+#define ARRIA10_ECC_HMC_OCP_MPR_ECC_REG2RDDATABUS_BEAT3 (ARRIA10_SDR_ADDR + 0x17c)
+
+#define ARRIA10_NOC_DDR_T_MAIN_SCHEDULER_ID_COREID (ARRIA10_SDR_SCHEDULER_ADDR + 0x00)
+#define ARRIA10_NOC_DDR_T_MAIN_SCHEDULER_ID_REVISIONID (ARRIA10_SDR_SCHEDULER_ADDR + 0x04)
+#define ARRIA10_NOC_DDR_T_MAIN_SCHEDULER_DDRCONF (ARRIA10_SDR_SCHEDULER_ADDR + 0x08)
+#define ARRIA10_NOC_DDR_T_MAIN_SCHEDULER_DDRTIMING (ARRIA10_SDR_SCHEDULER_ADDR + 0x0c)
+#define ARRIA10_NOC_DDR_T_MAIN_SCHEDULER_DDRMODE (ARRIA10_SDR_SCHEDULER_ADDR + 0x10)
+#define ARRIA10_NOC_DDR_T_MAIN_SCHEDULER_READLATENCY (ARRIA10_SDR_SCHEDULER_ADDR + 0x14)
+#define ARRIA10_NOC_DDR_T_MAIN_SCHEDULER_ACTIVATE (ARRIA10_SDR_SCHEDULER_ADDR + 0x38)
+#define ARRIA10_NOC_DDR_T_MAIN_SCHEDULER_DEVTODEV (ARRIA10_SDR_SCHEDULER_ADDR + 0x3c)
+
+#define ARRIA10_IO48_HMC_MMR_DBGCFG0 (ARRIA10_HMC_MMR_IO48_ADDR + 0x00)
+#define ARRIA10_IO48_HMC_MMR_DBGCFG1 (ARRIA10_HMC_MMR_IO48_ADDR + 0x04)
+#define ARRIA10_IO48_HMC_MMR_DBGCFG2 (ARRIA10_HMC_MMR_IO48_ADDR + 0x08)
+#define ARRIA10_IO48_HMC_MMR_DBGCFG3 (ARRIA10_HMC_MMR_IO48_ADDR + 0x0c)
+#define ARRIA10_IO48_HMC_MMR_DBGCFG4 (ARRIA10_HMC_MMR_IO48_ADDR + 0x10)
+#define ARRIA10_IO48_HMC_MMR_DBGCFG5 (ARRIA10_HMC_MMR_IO48_ADDR + 0x14)
+#define ARRIA10_IO48_HMC_MMR_DBGCFG6 (ARRIA10_HMC_MMR_IO48_ADDR + 0x18)
+#define ARRIA10_IO48_HMC_MMR_RESERVE0 (ARRIA10_HMC_MMR_IO48_ADDR + 0x1c)
+#define ARRIA10_IO48_HMC_MMR_RESERVE1 (ARRIA10_HMC_MMR_IO48_ADDR + 0x20)
+#define ARRIA10_IO48_HMC_MMR_RESERVE2 (ARRIA10_HMC_MMR_IO48_ADDR + 0x24)
+#define ARRIA10_IO48_HMC_MMR_CTRLCFG0 (ARRIA10_HMC_MMR_IO48_ADDR + 0x28)
+#define ARRIA10_IO48_HMC_MMR_CTRLCFG1 (ARRIA10_HMC_MMR_IO48_ADDR + 0x2c)
+#define ARRIA10_IO48_HMC_MMR_CTRLCFG2 (ARRIA10_HMC_MMR_IO48_ADDR + 0x30)
+#define ARRIA10_IO48_HMC_MMR_CTRLCFG3 (ARRIA10_HMC_MMR_IO48_ADDR + 0x34)
+#define ARRIA10_IO48_HMC_MMR_CTRLCFG4 (ARRIA10_HMC_MMR_IO48_ADDR + 0x38)
+#define ARRIA10_IO48_HMC_MMR_CTRLCFG5 (ARRIA10_HMC_MMR_IO48_ADDR + 0x3c)
+#define ARRIA10_IO48_HMC_MMR_CTRLCFG6 (ARRIA10_HMC_MMR_IO48_ADDR + 0x40)
+#define ARRIA10_IO48_HMC_MMR_CTRLCFG7 (ARRIA10_HMC_MMR_IO48_ADDR + 0x44)
+#define ARRIA10_IO48_HMC_MMR_CTRLCFG8 (ARRIA10_HMC_MMR_IO48_ADDR + 0x48)
+#define ARRIA10_IO48_HMC_MMR_CTRLCFG9 (ARRIA10_HMC_MMR_IO48_ADDR + 0x4c)
+#define ARRIA10_IO48_HMC_MMR_DRAMTIMING0 (ARRIA10_HMC_MMR_IO48_ADDR + 0x50)
+#define ARRIA10_IO48_HMC_MMR_DRAMODT0 (ARRIA10_HMC_MMR_IO48_ADDR + 0x54)
+#define ARRIA10_IO48_HMC_MMR_DRAMODT1 (ARRIA10_HMC_MMR_IO48_ADDR + 0x58)
+#define ARRIA10_IO48_HMC_MMR_SBCFG0 (ARRIA10_HMC_MMR_IO48_ADDR + 0x5c)
+#define ARRIA10_IO48_HMC_MMR_SBCFG1 (ARRIA10_HMC_MMR_IO48_ADDR + 0x60)
+#define ARRIA10_IO48_HMC_MMR_SBCFG2 (ARRIA10_HMC_MMR_IO48_ADDR + 0x64)
+#define ARRIA10_IO48_HMC_MMR_SBCFG3 (ARRIA10_HMC_MMR_IO48_ADDR + 0x68)
+#define ARRIA10_IO48_HMC_MMR_SBCFG4 (ARRIA10_HMC_MMR_IO48_ADDR + 0x6c)
+#define ARRIA10_IO48_HMC_MMR_SBCFG5 (ARRIA10_HMC_MMR_IO48_ADDR + 0x70)
+#define ARRIA10_IO48_HMC_MMR_SBCFG6 (ARRIA10_HMC_MMR_IO48_ADDR + 0x74)
+#define ARRIA10_IO48_HMC_MMR_SBCFG7 (ARRIA10_HMC_MMR_IO48_ADDR + 0x78)
+#define ARRIA10_IO48_HMC_MMR_CALTIMING0 (ARRIA10_HMC_MMR_IO48_ADDR + 0x7c)
+#define ARRIA10_IO48_HMC_MMR_CALTIMING1 (ARRIA10_HMC_MMR_IO48_ADDR + 0x80)
+#define ARRIA10_IO48_HMC_MMR_CALTIMING2 (ARRIA10_HMC_MMR_IO48_ADDR + 0x84)
+#define ARRIA10_IO48_HMC_MMR_CALTIMING3 (ARRIA10_HMC_MMR_IO48_ADDR + 0x88)
+#define ARRIA10_IO48_HMC_MMR_CALTIMING4 (ARRIA10_HMC_MMR_IO48_ADDR + 0x8c)
+#define ARRIA10_IO48_HMC_MMR_CALTIMING5 (ARRIA10_HMC_MMR_IO48_ADDR + 0x90)
+#define ARRIA10_IO48_HMC_MMR_CALTIMING6 (ARRIA10_HMC_MMR_IO48_ADDR + 0x94)
+#define ARRIA10_IO48_HMC_MMR_CALTIMING7 (ARRIA10_HMC_MMR_IO48_ADDR + 0x98)
+#define ARRIA10_IO48_HMC_MMR_CALTIMING8 (ARRIA10_HMC_MMR_IO48_ADDR + 0x9c)
+#define ARRIA10_IO48_HMC_MMR_CALTIMING9 (ARRIA10_HMC_MMR_IO48_ADDR + 0xa0)
+#define ARRIA10_IO48_HMC_MMR_CALTIMING10 (ARRIA10_HMC_MMR_IO48_ADDR + 0xa4)
+#define ARRIA10_IO48_HMC_MMR_DRAMADDRW (ARRIA10_HMC_MMR_IO48_ADDR + 0xa8)
+#define ARRIA10_IO48_HMC_MMR_SIDEBAND0 (ARRIA10_HMC_MMR_IO48_ADDR + 0xac)
+#define ARRIA10_IO48_HMC_MMR_SIDEBAND1 (ARRIA10_HMC_MMR_IO48_ADDR + 0xb0)
+#define ARRIA10_IO48_HMC_MMR_SIDEBAND2 (ARRIA10_HMC_MMR_IO48_ADDR + 0xb4)
+#define ARRIA10_IO48_HMC_MMR_SIDEBAND3 (ARRIA10_HMC_MMR_IO48_ADDR + 0xb8)
+#define ARRIA10_IO48_HMC_MMR_SIDEBAND4 (ARRIA10_HMC_MMR_IO48_ADDR + 0xbc)
+#define ARRIA10_IO48_HMC_MMR_SIDEBAND5 (ARRIA10_HMC_MMR_IO48_ADDR + 0xc0)
+#define ARRIA10_IO48_HMC_MMR_SIDEBAND6 (ARRIA10_HMC_MMR_IO48_ADDR + 0xc4)
+#define ARRIA10_IO48_HMC_MMR_SIDEBAND7 (ARRIA10_HMC_MMR_IO48_ADDR + 0xc8)
+#define ARRIA10_IO48_HMC_MMR_SIDEBAND8 (ARRIA10_HMC_MMR_IO48_ADDR + 0xcc)
+#define ARRIA10_IO48_HMC_MMR_SIDEBAND9 (ARRIA10_HMC_MMR_IO48_ADDR + 0xd0)
+#define ARRIA10_IO48_HMC_MMR_SIDEBAND10 (ARRIA10_HMC_MMR_IO48_ADDR + 0xd4)
+#define ARRIA10_IO48_HMC_MMR_SIDEBAND11 (ARRIA10_HMC_MMR_IO48_ADDR + 0xd8)
+#define ARRIA10_IO48_HMC_MMR_SIDEBAND12 (ARRIA10_HMC_MMR_IO48_ADDR + 0xdc)
+#define ARRIA10_IO48_HMC_MMR_SIDEBANB13 (ARRIA10_HMC_MMR_IO48_ADDR + 0xe0)
+#define ARRIA10_IO48_HMC_MMR_SIDEBAND14 (ARRIA10_HMC_MMR_IO48_ADDR + 0xe4)
+#define ARRIA10_IO48_HMC_MMR_SIDEBAND15 (ARRIA10_HMC_MMR_IO48_ADDR + 0xe8)
+#define ARRIA10_IO48_HMC_MMR_DRAMSTS (ARRIA10_HMC_MMR_IO48_ADDR + 0xec)
+#define ARRIA10_IO48_HMC_MMR_DBGDONE (ARRIA10_HMC_MMR_IO48_ADDR + 0xf0)
+#define ARRIA10_IO48_HMC_MMR_DBGSIGNALS (ARRIA10_HMC_MMR_IO48_ADDR + 0xf4)
+#define ARRIA10_IO48_HMC_MMR_DBGRESET (ARRIA10_HMC_MMR_IO48_ADDR + 0xf8)
+#define ARRIA10_IO48_HMC_MMR_DBGMATCH (ARRIA10_HMC_MMR_IO48_ADDR + 0xfc)
+#define ARRIA10_IO48_HMC_MMR_COUNTER0MASK (ARRIA10_HMC_MMR_IO48_ADDR + 0x100)
+#define ARRIA10_IO48_HMC_MMR_COUNTER1MASK (ARRIA10_HMC_MMR_IO48_ADDR + 0x104)
+#define ARRIA10_IO48_HMC_MMR_COUNTER0MATCH (ARRIA10_HMC_MMR_IO48_ADDR + 0x108)
+#define ARRIA10_IO48_HMC_MMR_COUNTER1MATCH (ARRIA10_HMC_MMR_IO48_ADDR + 0x10c)
+#define ARRIA10_IO48_HMC_MMR_NIOSRESERVE0 (ARRIA10_HMC_MMR_IO48_ADDR + 0x110)
+#define ARRIA10_IO48_HMC_MMR_NIOSRESERVE1 (ARRIA10_HMC_MMR_IO48_ADDR + 0x114)
+#define ARRIA10_IO48_HMC_MMR_NIOSRESERVE2 (ARRIA10_HMC_MMR_IO48_ADDR + 0x118)
+
+union dramaddrw_reg {
+ struct {
+ u32 cfg_col_addr_width:5;
+ u32 cfg_row_addr_width:5;
+ u32 cfg_bank_addr_width:4;
+ u32 cfg_bank_group_addr_width:2;
+ u32 cfg_cs_addr_width:3;
+ u32 reserved:13;
+ };
+ u32 word;
+};
+
+union ctrlcfg0_reg {
+ struct {
+ u32 cfg_mem_type:4;
+ u32 cfg_dimm_type:3;
+ u32 cfg_ac_pos:2;
+ u32 cfg_ctrl_burst_len:5;
+ u32 reserved:18; /* Other fields unused */
+ };
+ u32 word;
+};
+
+union ctrlcfg1_reg {
+ struct {
+ u32 cfg_dbc3_burst_len:5;
+ u32 cfg_addr_order:2;
+ u32 cfg_ctrl_enable_ecc:1;
+ u32 reserved:24; /* Other fields unused */
+ };
+ u32 word;
+};
+
+union caltiming0_reg {
+ struct {
+ u32 cfg_act_to_rdwr:6;
+ u32 cfg_act_to_pch:6;
+ u32 cfg_act_to_act:6;
+ u32 cfg_act_to_act_db:6;
+ u32 reserved:8; /* Other fields unused */
+ };
+ u32 word;
+};
+
+union caltiming1_reg {
+ struct {
+ u32 cfg_rd_to_rd:6;
+ u32 cfg_rd_to_rd_dc:6;
+ u32 cfg_rd_to_rd_db:6;
+ u32 cfg_rd_to_wr:6;
+ u32 cfg_rd_to_wr_dc:6;
+ u32 reserved:2;
+ };
+ u32 word;
+};
+
+union caltiming2_reg {
+ struct {
+ u32 cfg_rd_to_wr_db:6;
+ u32 cfg_rd_to_pch:6;
+ u32 cfg_rd_ap_to_valid:6;
+ u32 cfg_wr_to_wr:6;
+ u32 cfg_wr_to_wr_dc:6;
+ u32 reserved:2;
+ };
+ u32 word;
+};
+
+union caltiming3_reg {
+ struct {
+ u32 cfg_wr_to_wr_db:6;
+ u32 cfg_wr_to_rd:6;
+ u32 cfg_wr_to_rd_dc:6;
+ u32 cfg_wr_to_rd_db:6;
+ u32 cfg_wr_to_pch:6;
+ u32 reserved:2;
+ };
+ u32 word;
+};
+
+union caltiming4_reg {
+ struct {
+ u32 cfg_wr_ap_to_valid:6;
+ u32 cfg_pch_to_valid:6;
+ u32 cfg_pch_all_to_valid:6;
+ u32 cfg_arf_to_valid:8;
+ u32 cfg_pdn_to_valid:6;
+ };
+ u32 word;
+};
+
+union caltiming9_reg {
+ struct {
+ u32 cfg_4_act_to_act:8;
+ u32 reserved:24;
+ };
+ u32 word;
+};
+
+#define IRQ_ECC_SERR 34
+#define IRQ_ECC_DERR 32
+
+#define ARRIA10_ECC_HMC_OCP_DDRIOCTRL_IO_SIZE 0x00000001
+
+#define ARRIA10_ECC_HMC_OCP_INTSTAT_SERRPENA 0x00000001
+#define ARRIA10_ECC_HMC_OCP_INTSTAT_DERRPENA 0x00000002
+#define ARRIA10_ECC_HMC_OCP_ERRINTEN_SERRINTEN 0x00000001
+#define ARRIA10_ECC_HMC_OCP_ERRINTEN_DERRINTEN 0x00000002
+#define ARRIA10_ECC_HMC_OCP_INTMOD_INTONCMP 0x00010000
+#define ARRIA10_ECC_HMC_OCP_INTMOD_SERR 0x00000001
+#define ARRIA10_ECC_HMC_OCP_INTMOD_EXT_ADDRPARITY 0x00000100
+#define ARRIA10_ECC_HMC_OCP_ECCCTL_AWB_CNT_RST 0x00010000
+#define ARRIA10_ECC_HMC_OCP_ECCCTL_CNT_RST 0x00000100
+#define ARRIA10_ECC_HMC_OCP_ECCCTL_ECC_EN 0x00000000
+#define ARRIA10_ECC_HMC_OCP_ECCCTL2_RMW_EN 0x00000100
+#define ARRIA10_ECC_HMC_OCP_ECCCTL2_AWB_EN 0x00000001
+#define ARRIA10_ECC_HMC_OCP_ERRINTEN_SERR 0x00000001
+#define ARRIA10_ECC_HMC_OCP_ERRINTEN_DERR 0x00000002
+#define ARRIA10_ECC_HMC_OCP_ERRINTEN_HMI 0x00000004
+#define ARRIA10_ECC_HMC_OCP_INTSTAT_SERR 0x00000001
+#define ARRIA10_ECC_HMC_OCP_INTSTAT_DERR 0x00000002
+#define ARRIA10_ECC_HMC_OCP_INTSTAT_HMI 0x00000004
+#define ARRIA10_ECC_HMC_OCP_INTSTAT_ADDRMTCFLG 0x00010000
+#define ARRIA10_ECC_HMC_OCP_INTSTAT_ADDRPARFLG 0x00020000
+#define ARRIA10_ECC_HMC_OCP_INTSTAT_DERRBUSFLG 0x00040000
+
+#define ARRIA10_ECC_HMC_OCP_SERRCNTREG_VALUE 8
+
+#define ARRIA10_NOC_MPU_DDR_T_SCHED_DDRTIMING_ACTTOACT_LSB 22
+#define ARRIA10_NOC_MPU_DDR_T_SCHED_DDRTIMING_RDTOMISS_LSB 0
+#define ARRIA10_NOC_MPU_DDR_T_SCHED_DDRTIMING_WRTOMISS_LSB 0
+#define ARRIA10_NOC_MPU_DDR_T_SCHED_DDRTIMING_BURSTLEN_LSB 2
+#define ARRIA10_NOC_MPU_DDR_T_SCHED_DDRTIMING_RDTOWR_LSB 6
+#define ARRIA10_NOC_MPU_DDR_T_SCHED_DDRTIMING_WRTORD_LSB 15
+#define ARRIA10_NOC_MPU_DDR_T_SCHED_DDRTIMING_BWRATIO_LSB 0
+
+#define ARRIA10_NOC_MPU_DDR_T_SCHED_DDRMOD_AUTOPRECHARGE_LSB 0
+#define ARRIA10_NOC_MPU_DDR_T_SCHED_DDRMOD_BWRATIOEXTENDED_LSB 0
+
+#define ARRIA10_NOC_MPU_DDR_T_SCHED_ACTIVATE_RRD_LSB 4
+#define ARRIA10_NOC_MPU_DDR_T_SCHED_ACTIVATE_FAW_LSB 13
+#define ARRIA10_NOC_MPU_DDR_T_SCHED_ACTIVATE_FAWBANK_LSB 4
+
+#define ARRIA10_NOC_MPU_DDR_T_SCHED_DEVTODEV_BUSRDTORD_LSB 4
+#define ARRIA10_NOC_MPU_DDR_T_SCHED_DEVTODEV_BUSRDTOWR_LSB 6
+#define ARRIA10_NOC_MPU_DDR_T_SCHED_DEVTODEV_BUSWRTORD_LSB 6
+
+#define ARRIA10_SDR_FW_MPU_FPGA_EN (ARRIA10_SDR_FW_MPU_FPGA_ADDR + 0x00)
+#define ARRIA10_SDR_FW_MPU_FPGA_EN_SET (ARRIA10_SDR_FW_MPU_FPGA_ADDR + 0x04)
+#define ARRIA10_SDR_FW_MPU_FPGA_EN_CLR (ARRIA10_SDR_FW_MPU_FPGA_ADDR + 0x08)
+#define ARRIA10_SDR_FW_MPU_FPGA_MPUREGION0ADDR (ARRIA10_SDR_FW_MPU_FPGA_ADDR + 0x10)
+#define ARRIA10_SDR_FW_MPU_FPGA_MPUREGION1ADDR (ARRIA10_SDR_FW_MPU_FPGA_ADDR + 0x14)
+#define ARRIA10_SDR_FW_MPU_FPGA_MPUREGION2ADDR (ARRIA10_SDR_FW_MPU_FPGA_ADDR + 0x18)
+#define ARRIA10_SDR_FW_MPU_FPGA_MPUREGION3ADDR (ARRIA10_SDR_FW_MPU_FPGA_ADDR + 0x1c)
+#define ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM0REGION0ADDR (ARRIA10_SDR_FW_MPU_FPGA_ADDR + 0x20)
+#define ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM0REGION1ADDR (ARRIA10_SDR_FW_MPU_FPGA_ADDR + 0x24)
+#define ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM0REGION2ADDR (ARRIA10_SDR_FW_MPU_FPGA_ADDR + 0x28)
+#define ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM0REGION3ADDR (ARRIA10_SDR_FW_MPU_FPGA_ADDR + 0x2c)
+#define ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM1REGION0ADDR (ARRIA10_SDR_FW_MPU_FPGA_ADDR + 0x30)
+#define ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM1REGION1ADDR (ARRIA10_SDR_FW_MPU_FPGA_ADDR + 0x34)
+#define ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM1REGION2ADDR (ARRIA10_SDR_FW_MPU_FPGA_ADDR + 0x38)
+#define ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM1REGION3ADDR (ARRIA10_SDR_FW_MPU_FPGA_ADDR + 0x3c)
+#define ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM2REGION0ADDR (ARRIA10_SDR_FW_MPU_FPGA_ADDR + 0x40)
+#define ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM2REGION1ADDR (ARRIA10_SDR_FW_MPU_FPGA_ADDR + 0x44)
+#define ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM2REGION2ADDR (ARRIA10_SDR_FW_MPU_FPGA_ADDR + 0x48)
+#define ARRIA10_SDR_FW_MPU_FPGA_FPGA2SDRAM2REGION3ADDR (ARRIA10_SDR_FW_MPU_FPGA_ADDR + 0x4c)
+
+#define ARRIA10_NOC_FW_DDR_MPU_MPUREG0EN BIT(0)
+#define ARRIA10_NOC_FW_DDR_MPU_MPUREG1EN BIT(1)
+#define ARRIA10_NOC_FW_DDR_MPU_MPUREG2EN BIT(2)
+#define ARRIA10_NOC_FW_DDR_MPU_MPUREG3EN BIT(3)
+#define ARRIA10_NOC_FW_DDR_MPU_F2SDR0REG0EN BIT(4)
+#define ARRIA10_NOC_FW_DDR_MPU_F2SDR0REG1EN BIT(5)
+#define ARRIA10_NOC_FW_DDR_MPU_F2SDR0REG2EN BIT(6)
+#define ARRIA10_NOC_FW_DDR_MPU_F2SDR0REG3EN BIT(7)
+#define ARRIA10_NOC_FW_DDR_MPU_F2SDR1REG0EN BIT(8)
+#define ARRIA10_NOC_FW_DDR_MPU_F2SDR1REG1EN BIT(9)
+#define ARRIA10_NOC_FW_DDR_MPU_F2SDR1REG2EN BIT(10)
+#define ARRIA10_NOC_FW_DDR_MPU_F2SDR1REG3EN BIT(11)
+#define ARRIA10_NOC_FW_DDR_MPU_F2SDR2REG0EN BIT(12)
+#define ARRIA10_NOC_FW_DDR_MPU_F2SDR2REG1EN BIT(13)
+#define ARRIA10_NOC_FW_DDR_MPU_F2SDR2REG2EN BIT(14)
+#define ARRIA10_NOC_FW_DDR_MPU_F2SDR2REG3EN BIT(15)
+
+#define ARRIA10_NOC_FW_DDR_L3_EN (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x00)
+#define ARRIA10_NOC_FW_DDR_L3_EN_SET (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x04)
+#define ARRIA10_NOC_FW_DDR_L3_EN_CLR (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x08)
+#define ARRIA10_NOC_FW_DDR_L3_HPSREGION0ADDR (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x0c)
+#define ARRIA10_NOC_FW_DDR_L3_HPSREGION1ADDR (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x10)
+#define ARRIA10_NOC_FW_DDR_L3_HPSREGION2ADDR (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x14)
+#define ARRIA10_NOC_FW_DDR_L3_HPSREGION3ADDR (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x18)
+#define ARRIA10_NOC_FW_DDR_L3_HPSREGION4ADDR (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x1c)
+#define ARRIA10_NOC_FW_DDR_L3_HPSREGION5ADDR (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x20)
+#define ARRIA10_NOC_FW_DDR_L3_HPSREGION6ADDR (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x24)
+#define ARRIA10_NOC_FW_DDR_L3_HPSREGION7ADDR (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x28)
+#define ARRIA10_NOC_FW_DDR_L3_GLOBAL (ARRIA10_NOC_FW_DDR_L3_DDR_SCR_ADDR + 0x2c)
+
+#define ARRIA10_NOC_FW_DDR_L3_HPSREG0EN BIT(0)
+#define ARRIA10_NOC_FW_DDR_L3_HPSREG1EN BIT(1)
+#define ARRIA10_NOC_FW_DDR_L3_HPSREG2EN BIT(2)
+#define ARRIA10_NOC_FW_DDR_L3_HPSREG3EN BIT(3)
+#define ARRIA10_NOC_FW_DDR_L3_HPSREG4EN BIT(4)
+#define ARRIA10_NOC_FW_DDR_L3_HPSREG5EN BIT(5)
+#define ARRIA10_NOC_FW_DDR_L3_HPSREG6EN BIT(6)
+#define ARRIA10_NOC_FW_DDR_L3_HPSREG7EN BIT(7)
+
+#define ARRIA10_IO48_DRAMTIME_MEM_READ_LATENCY 0x0000003f
+
+int arria10_ddr_calibration_sequence(void);
+
+#endif
diff --git a/arch/arm/mach-socfpga/include/mach/arria10-system-manager.h b/arch/arm/mach-socfpga/include/mach/arria10-system-manager.h
new file mode 100644
index 000000000000..f98cc36c7664
--- /dev/null
+++ b/arch/arm/mach-socfpga/include/mach/arria10-system-manager.h
@@ -0,0 +1,97 @@
+/*
+ * Copyright (C) 2014-2016 Altera Corporation <www.altera.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+#ifndef _ARRIA10_SYSTEM_MANAGER_H_
+#define _ARRIA10_SYSTEM_MANAGER_H_
+
+#include <mach/arria10-regs.h>
+
+#define ARRIA10_SYSMGR_SILICONID1 (ARRIA10_SYSMGR_ADDR + 0x00)
+#define ARRIA10_SYSMGR_SILICONID2 (ARRIA10_SYSMGR_ADDR + 0x04)
+#define ARRIA10_SYSMGR_WDDBG (ARRIA10_SYSMGR_ADDR + 0x08)
+#define ARRIA10_SYSMGR_BOOTINFO (ARRIA10_SYSMGR_ADDR + 0x0c)
+#define ARRIA10_SYSMGR_MPU_CTRL_L2_ECC (ARRIA10_SYSMGR_ADDR + 0x10)
+#define ARRIA10_SYSMGR_DMA (ARRIA10_SYSMGR_ADDR + 0x20)
+#define ARRIA10_SYSMGR_DMA_PERIPH (ARRIA10_SYSMGR_ADDR + 0x24)
+#define ARRIA10_SYSMGR_SDMMC (ARRIA10_SYSMGR_ADDR + 0x28)
+#define ARRIA10_SYSMGR_SDMMC_L3MASTER (ARRIA10_SYSMGR_ADDR + 0x2c)
+#define ARRIA10_SYSMGR_NAND_BOOTSTRAP (ARRIA10_SYSMGR_ADDR + 0x30)
+#define ARRIA10_SYSMGR_NAND_L3MASTER (ARRIA10_SYSMGR_ADDR + 0x34)
+#define ARRIA10_SYSMGR_USB0_L3MASTER (ARRIA10_SYSMGR_ADDR + 0x38)
+#define ARRIA10_SYSMGR_USB1_L3MASTER (ARRIA10_SYSMGR_ADDR + 0x3c)
+#define ARRIA10_SYSMGR_EMAC_GLOBAL (ARRIA10_SYSMGR_ADDR + 0x40)
+#define ARRIA10_SYSMGR_EMAC0 (ARRIA10_SYSMGR_ADDR + 0x44)
+#define ARRIA10_SYSMGR_EMAC1 (ARRIA10_SYSMGR_ADDR + 0x48)
+#define ARRIA10_SYSMGR_EMAC2 (ARRIA10_SYSMGR_ADDR + 0x4c)
+#define ARRIA10_SYSMGR_FPGAINTF_GLOBAL (ARRIA10_SYSMGR_ADDR + 0x60)
+#define ARRIA10_SYSMGR_FPGAINTF_EN_0 (ARRIA10_SYSMGR_ADDR + 0x64)
+#define ARRIA10_SYSMGR_FPGAINTF_EN_1 (ARRIA10_SYSMGR_ADDR + 0x68)
+#define ARRIA10_SYSMGR_FPGAINTF_EN_2 (ARRIA10_SYSMGR_ADDR + 0x6c)
+#define ARRIA10_SYSMGR_FPGAINTF_EN_3 (ARRIA10_SYSMGR_ADDR + 0x70)
+#define ARRIA10_SYSMGR_NOC_ADDR_REMAP_VALUE (ARRIA10_SYSMGR_ADDR + 0x80)
+#define ARRIA10_SYSMGR_NOC_ADDR_REMAP_SET (ARRIA10_SYSMGR_ADDR + 0x84)
+#define ARRIA10_SYSMGR_NOC_ADDR_REMAP_CLEAR (ARRIA10_SYSMGR_ADDR + 0x88)
+#define ARRIA10_SYSMGR_ECC_INTMASK_VALUE (ARRIA10_SYSMGR_ADDR + 0x90)
+#define ARRIA10_SYSMGR_ECC_INTMASK_SET (ARRIA10_SYSMGR_ADDR + 0x94)
+#define ARRIA10_SYSMGR_ECC_INTMASK_CLR (ARRIA10_SYSMGR_ADDR + 0x98)
+#define ARRIA10_SYSMGR_ECC_INTSTATUS_SERR (ARRIA10_SYSMGR_ADDR + 0x9c)
+#define ARRIA10_SYSMGR_ECC_INTSTATUS_DERR (ARRIA10_SYSMGR_ADDR + 0xa0)
+#define ARRIA10_SYSMGR_MPU_STATUS_L2_ECC (ARRIA10_SYSMGR_ADDR + 0xa4)
+#define ARRIA10_SYSMGR_MPU_CLEAR_L2_ECC (ARRIA10_SYSMGR_ADDR + 0xa8)
+#define ARRIA10_SYSMGR_MPU_STATUS_L1_PARITY (ARRIA10_SYSMGR_ADDR + 0xac)
+#define ARRIA10_SYSMGR_MPU_CLEAR_L1_PARITY (ARRIA10_SYSMGR_ADDR + 0xb0)
+#define ARRIA10_SYSMGR_MPU_SET_L1_PARITY (ARRIA10_SYSMGR_ADDR + 0xb4)
+#define ARRIA10_SYSMGR_NOC_TIMEOUT (ARRIA10_SYSMGR_ADDR + 0xc0)
+#define ARRIA10_SYSMGR_NOC_IDLEREQ_SET (ARRIA10_SYSMGR_ADDR + 0xc4)
+#define ARRIA10_SYSMGR_NOC_IDLEREQ_CLR (ARRIA10_SYSMGR_ADDR + 0xc8)
+#define ARRIA10_SYSMGR_NOC_IDLEREQ_VALUE (ARRIA10_SYSMGR_ADDR + 0xcc)
+#define ARRIA10_SYSMGR_NOC_IDLEACK (ARRIA10_SYSMGR_ADDR + 0xd0)
+#define ARRIA10_SYSMGR_NOC_IDLESTATUS (ARRIA10_SYSMGR_ADDR + 0xd4)
+#define ARRIA10_SYSMGR_FPGA2SOC_CTRL (ARRIA10_SYSMGR_ADDR + 0xd8)
+
+/* pin mux */
+#define ARRIA10_SYSMGR_PINMUXGRP (ARRIA10_SYSMGR_ADDR + 0x400)
+#define ARRIA10_SYSMGR_PINMUXGRP_NANDUSEFPGA (ARRIA10_SYSMGR_PINMUXGRP + 0x2F0)
+#define ARRIA10_SYSMGR_PINMUXGRP_EMAC1USEFPGA (ARRIA10_SYSMGR_PINMUXGRP + 0x2F8)
+#define ARRIA10_SYSMGR_PINMUXGRP_SDMMCUSEFPGA (ARRIA10_SYSMGR_PINMUXGRP + 0x308)
+#define ARRIA10_SYSMGR_PINMUXGRP_EMAC0USEFPGA (ARRIA10_SYSMGR_PINMUXGRP + 0x314)
+#define ARRIA10_SYSMGR_PINMUXGRP_SPIM1USEFPGA (ARRIA10_SYSMGR_PINMUXGRP + 0x330)
+#define ARRIA10_SYSMGR_PINMUXGRP_SPIM0USEFPGA (ARRIA10_SYSMGR_PINMUXGRP + 0x338)
+
+/* bit fields */
+#define ARRIA10_SYSMGR_ROMCODEGRP_CTRL_WARMRSTCFGPINMUX BIT(0)
+#define ARRIA10_SYSMGR_ROMCODEGRP_CTRL_WARMRSTCFGIO BIT(1)
+#define ARRIA10_SYSMGR_ECC_OCRAM_EN BIT(0)
+#define ARRIA10_SYSMGR_ECC_OCRAM_SERR BIT(3)
+#define ARRIA10_SYSMGR_ECC_OCRAM_DERR BIT(4)
+#define ARRIA10_SYSMGR_FPGAINTF_USEFPGA BIT(1)
+#define ARRIA10_SYSMGR_FPGAINTF_SPIM0 BIT(0)
+#define ARRIA10_SYSMGR_FPGAINTF_SPIM1 BIT(1)
+#define ARRIA10_SYSMGR_FPGAINTF_EMAC0 BIT(2)
+#define ARRIA10_SYSMGR_FPGAINTF_EMAC1 BIT(3)
+#define ARRIA10_SYSMGR_FPGAINTF_NAND BIT(4)
+#define ARRIA10_SYSMGR_FPGAINTF_SDMMC BIT(5)
+
+#define ARRIA10_SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_GMII_MII 0x0
+#define ARRIA10_SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_RGMII 0x1
+#define ARRIA10_SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_RMII 0x2
+#define ARRIA10_SYSMGR_EMACGRP_CTRL_PHYSEL_LSB 0
+#define ARRIA10_SYSMGR_EMACGRP_CTRL_PHYSEL_MASK 0x00000003
+
+#define ARRIA10_SYSMGR_FPGAINTF_EN3_EMAC0 BIT(0)
+#define ARRIA10_SYSMGR_FPGAINTF_EN3_EMAC0_SW BIT(4)
+#define ARRIA10_SYSMGR_FPGAINTF_EN3_EMAC1 BIT(8)
+#define ARRIA10_SYSMGR_FPGAINTF_EN3_EMAC1_SW BIT(12)
+#define ARRIA10_SYSMGR_FPGAINTF_EN3_EMAC2 BIT(16)
+#define ARRIA10_SYSMGR_FPGAINTF_EN3_EMAC2_SW BIT(20)
+
+#define ARRIA10_SYSMGR_SDMMC_SMPLSEL(smplsel) (((smplsel) & 0x7) << 4)
+#define ARRIA10_SYSMGR_SDMMC_DRVSEL(drvsel) ((drvsel) & 0x7)
+
+#define SYSMGR_SDMMC_CTRL_SET(smplsel, drvsel) \
+ ((drvsel << 0) & 0x7) | ((smplsel << 4) & 0x70)
+
+#endif
diff --git a/arch/arm/mach-socfpga/include/mach/generic.h b/arch/arm/mach-socfpga/include/mach/generic.h
index 2a7e0ea499af..4a5b1bbc2843 100644
--- a/arch/arm/mach-socfpga/include/mach/generic.h
+++ b/arch/arm/mach-socfpga/include/mach/generic.h
@@ -5,9 +5,44 @@ struct socfpga_cm_config;
struct socfpga_io_config;
+struct arria10_mainpll_cfg;
+struct arria10_perpll_cfg;
+struct arria10_pinmux_cfg;
+
+void arria10_init(struct arria10_mainpll_cfg *mainpll,
+ struct arria10_perpll_cfg *perpll,
+ struct arria10_pinmux_cfg *pinmux);
+
void socfpga_lowlevel_init(struct socfpga_cm_config *cm_config,
struct socfpga_io_config *io_config);
+#if defined(CONFIG_ARCH_SOCFPGA_CYCLONE5)
+void socfpga_cyclone5_mmc_init(void);
+void socfpga_cyclone5_uart_init(void);
+void socfpga_cyclone5_timer_init(void);
+void socfpga_cyclone5_qspi_init(void);
+#else
+static inline void socfpga_cyclone5_mmc_init(void)
+{
+ return;
+}
+
+static inline void socfpga_cyclone5_uart_init(void)
+{
+ return;
+}
+
+static inline void socfpga_cyclone5_timer_init(void)
+{
+ return;
+}
+
+static inline void socfpga_cyclone5_qspi_init(void)
+{
+ return;
+}
+#endif
+
static inline void __udelay(unsigned us)
{
volatile unsigned int i;
diff --git a/arch/arm/mach-socfpga/xload.c b/arch/arm/mach-socfpga/xload.c
index 5d47bb9d3ea2..ee7d194427ec 100644
--- a/arch/arm/mach-socfpga/xload.c
+++ b/arch/arm/mach-socfpga/xload.c
@@ -1,8 +1,5 @@
-#include <platform_data/cadence_qspi.h>
-#include <platform_data/dw_mmc.h>
#include <bootsource.h>
#include <bootstrap.h>
-#include <platform_data/serial-ns16550.h>
#include <common.h>
#include <malloc.h>
#include <init.h>
@@ -10,7 +7,6 @@
#include <linux/sizes.h>
#include <fs.h>
#include <io.h>
-#include <mci.h>
#include <linux/clkdev.h>
#include <linux/stat.h>
@@ -30,84 +26,6 @@ static struct socfpga_barebox_part default_parts[] = {
};
const struct socfpga_barebox_part *barebox_parts = default_parts;
-enum socfpga_clks {
- timer, mmc, qspi_clk, uart, clk_max
-};
-
-static struct clk *clks[clk_max];
-
-static struct dw_mmc_platform_data mmc_pdata = {
- .bus_width_caps = MMC_CAP_4_BIT_DATA,
- .ciu_div = 3,
-};
-
-static void socfpga_mmc_init(void)
-{
- clks[mmc] = clk_fixed("mmc", 400000000);
- clkdev_add_physbase(clks[mmc], CYCLONE5_SDMMC_ADDRESS, NULL);
- add_generic_device("dw_mmc", 0, NULL, CYCLONE5_SDMMC_ADDRESS, SZ_4K,
- IORESOURCE_MEM, &mmc_pdata);
-}
-
-#if defined(CONFIG_SPI_CADENCE_QUADSPI)
-static struct cadence_qspi_platform_data qspi_pdata = {
- .ext_decoder = 0,
- .fifo_depth = 128,
-};
-
-static __maybe_unused void add_cadence_qspi_device(int id, resource_size_t ctrl,
- resource_size_t data, void *pdata)
-{
- struct resource *res;
-
- res = xzalloc(sizeof(struct resource) * 2);
- res[0].start = ctrl;
- res[0].end = ctrl + 0x100 - 1;
- res[0].flags = IORESOURCE_MEM;
- res[1].start = data;
- res[1].end = data + 0x100 - 1;
- res[1].flags = IORESOURCE_MEM;
-
- add_generic_device_res("cadence_qspi", id, res, 2, pdata);
-}
-
-static __maybe_unused void socfpga_qspi_init(void)
-{
- clks[qspi_clk] = clk_fixed("qspi_clk", 370000000);
- clkdev_add_physbase(clks[qspi_clk], CYCLONE5_QSPI_CTRL_ADDRESS, NULL);
- clkdev_add_physbase(clks[qspi_clk], CYCLONE5_QSPI_DATA_ADDRESS, NULL);
- add_cadence_qspi_device(0, CYCLONE5_QSPI_CTRL_ADDRESS,
- CYCLONE5_QSPI_DATA_ADDRESS, &qspi_pdata);
-}
-#else
-static void socfpga_qspi_init(void)
-{
- return;
-}
-#endif
-
-static struct NS16550_plat uart_pdata = {
- .clock = 100000000,
- .shift = 2,
-};
-
-static void socfpga_uart_init(void)
-{
- clks[uart] = clk_fixed("uart", 100000000);
- clkdev_add_physbase(clks[uart], CYCLONE5_UART0_ADDRESS, NULL);
- clkdev_add_physbase(clks[uart], CYCLONE5_UART1_ADDRESS, NULL);
- add_ns16550_device(0, 0xffc02000, 1024, IORESOURCE_MEM |
- IORESOURCE_MEM_8BIT, &uart_pdata);
-}
-
-static void socfpga_timer_init(void)
-{
- clks[timer] = clk_fixed("timer", 200000000);
- clkdev_add_physbase(clks[timer], CYCLONE5_SMP_TWD_ADDRESS, NULL);
- add_generic_device("smp_twd", 0, NULL, CYCLONE5_SMP_TWD_ADDRESS, 0x100,
- IORESOURCE_MEM, NULL);
-}
-
static __noreturn int socfpga_xload(void)
{
enum bootsource bootsource = bootsource_get();
@@ -116,7 +34,7 @@ static __noreturn int socfpga_xload(void)
switch (bootsource) {
case BOOTSOURCE_MMC:
- socfpga_mmc_init();
+ socfpga_cyclone5_mmc_init();
for (part = barebox_parts; part->mmc_disk; part++) {
buf = bootstrap_read_disk(barebox_parts->mmc_disk, "fat");
@@ -132,8 +50,7 @@ static __noreturn int socfpga_xload(void)
}
break;
case BOOTSOURCE_SPI:
- socfpga_qspi_init();
-
+ socfpga_cyclone5_qspi_init();
for (part = barebox_parts; part->nor_size; part++) {
buf = bootstrap_read_devfs("mtd0", false,
part->nor_offset, part->nor_size, SZ_1M);
@@ -142,7 +59,6 @@ static __noreturn int socfpga_xload(void)
part->nor_offset);
continue;
}
-
break;
}
@@ -167,8 +83,8 @@ static __noreturn int socfpga_xload(void)
static int socfpga_devices_init(void)
{
barebox_set_model("SoCFPGA");
- socfpga_timer_init();
- socfpga_uart_init();
+ socfpga_cyclone5_timer_init();
+ socfpga_cyclone5_uart_init();
barebox_main = socfpga_xload;
diff --git a/images/Makefile.socfpga b/images/Makefile.socfpga
index 21804d93df72..d210a6cc2318 100644
--- a/images/Makefile.socfpga
+++ b/images/Makefile.socfpga
@@ -4,11 +4,19 @@
# %.socfpgaimg - convert into socfpga image
# ----------------------------------------------------------------
+ifdef CONFIG_ARCH_SOCFPGA_ARRIA10
+quiet_cmd_socfpga_image = SOCFPGA-IMG $@
+ cmd_socfpga_image = scripts/socfpga_mkimage -o $@ -b -v1 $<
+
+$(obj)/%.socfpgaimg: $(obj)/% FORCE
+ $(call if_changed,socfpga_image)
+else
quiet_cmd_socfpga_image = SOCFPGA-IMG $@
cmd_socfpga_image = scripts/socfpga_mkimage -o $@ $<
$(obj)/%.socfpgaimg: $(obj)/% FORCE
$(call if_changed,socfpga_image)
+endif
# ----------------------- Cyclone5 based boards ---------------------------
pblx-$(CONFIG_MACH_SOCFPGA_ALTERA_SOCDK) += start_socfpga_socdk_xload
diff --git a/scripts/socfpga_mkimage.c b/scripts/socfpga_mkimage.c
index d7fe1b1b69f7..3763044aacab 100644
--- a/scripts/socfpga_mkimage.c
+++ b/scripts/socfpga_mkimage.c
@@ -62,6 +62,7 @@ static uint32_t bb_header[] = {
0x00000000, /* socfpga header */
0x00000000, /* socfpga header */
0x00000000, /* socfpga header */
+ 0x00000000, /* socfpga header */
0xea00006b, /* entry. b 0x200 (offset may be adjusted) */
};
diff --git a/scripts/socfpga_xml_to_config.sh b/scripts/socfpga_xml_to_config.sh
new file mode 100755
index 000000000000..154ddda720f9
--- /dev/null
+++ b/scripts/socfpga_xml_to_config.sh
@@ -0,0 +1,86 @@
+#!/bin/bash
+
+## TODO:
+## - read in mpuclk and nocclk, must be calculated by hand at the moment
+## - read in cfg_dedicated_io_*, must be calculated by hand at the moment
+
+if [ "$#" -lt "2" ]
+then
+ echo "USAGE: $0 <boarddir> <HPS.xml>"
+ exit 1
+fi
+
+dir=$1
+xml=$2
+
+pll_config() {
+ local src
+ local tgt
+ src=$1
+ tgt=$2
+
+ MAINPLL=`grep mainpll "$src" | \
+ sed -e 's/^.*mainpllgrp\.//g' | \
+ sed -e 's/\./_/g' | \
+ sed -e "s/' value/ /g" | \
+ sed -e "s/'/ /g" | \
+ sed -e "s# />#,#g" | \
+ sed -e "s/^/./g"`
+
+ PERPLL=`grep perpll "$src" | \
+ sed -e 's/^.*perpllgrp\.//g' | \
+ sed -e 's/\./_/g' | \
+ sed -e "s/' value/ /g" | \
+ sed -e "s/'/ /g" | \
+ sed -e "s# />#,#g" | \
+ sed -e "s/^/./g"`
+
+ echo "#include <mach/clock-manager-arria10.h>" > $tgt
+ echo >> $tgt
+ echo "static struct arria10_mainpll_cfg mainpll_cfg = {" >> $tgt
+ echo "$MAINPLL" >> $tgt
+ echo "};" >> $tgt
+ echo >> $tgt
+ echo "static struct arria10_perpll_cfg perpll_cfg = {" >> $tgt
+ echo "$PERPLL" >> $tgt
+ echo "};" >> $tgt
+
+ dos2unix $tgt
+}
+
+pinmux_config() {
+ local src
+ local tgt
+ src=$1
+ tgt=$2
+
+ SHARED=`grep pinmux_shared "$src" | \
+ sed -e 's/^.*pinmux_/\./g' | \
+ sed -e "s/\.sel' value='/=/g" | \
+ sed -e "s/' \/>/,/g"`
+
+ DEDICATED=`grep pinmux_dedicated "$src" | \
+ sed -e 's/^.*pinmux_/\./g' | \
+ sed -e "s/\.sel' value='/=/g" | \
+ sed -e "s/' \/>/,/g"`
+
+ FPGA=`grep _fpga_interface_ "$src" | \
+ sed -e 's/^.*pinmux_/\./g' | \
+ sed -e "s/\.sel' value='/=/g" | \
+ sed -e "s/' \/>/,/g"`
+
+ echo "#include <mach/arria10-pinmux.h>" > $tgt
+ echo >> $tgt
+ echo "static struct arria10_pinmux_cfg pinmux = {" >> $tgt
+ echo "$SHARED" >> $tgt
+ echo "$DEDICATED" >> $tgt
+ echo "$FPGA" >> $tgt
+ echo "};" >> $tgt
+ echo >> $tgt
+
+ dos2unix $tgt
+}
+
+pll_config $xml $dir/pll-config-arria10.c
+
+pinmux_config $xml $dir/pinmux-config-arria10.c
--
2.11.0
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 12+ messages in thread* [PATCH 6/7] ARM: socfpga: add support for reflex achilles board
2017-04-03 10:55 [PATCH 0/7] SoCFPGA: add support for Arria10 Steffen Trumtrar
` (4 preceding siblings ...)
2017-04-03 10:55 ` [PATCH 5/7] clk: socfpga: add arria10 clk drivers Steffen Trumtrar
@ 2017-04-03 10:55 ` Steffen Trumtrar
2017-04-03 10:55 ` [PATCH 7/7] ARM: socfpga: add arria10 defconfig Steffen Trumtrar
2017-04-04 17:52 ` [PATCH 0/7] SoCFPGA: add support for Arria10 Trent Piepho
7 siblings, 0 replies; 12+ messages in thread
From: Steffen Trumtrar @ 2017-04-03 10:55 UTC (permalink / raw)
To: barebox; +Cc: Steffen Trumtrar
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
---
arch/arm/boards/Makefile | 1 +
arch/arm/boards/reflex-achilles/Makefile | 2 +
arch/arm/boards/reflex-achilles/hps.xml | 351 +++++++++++++++++++++
arch/arm/boards/reflex-achilles/lowlevel.c | 48 +++
.../boards/reflex-achilles/pinmux-config-arria10.c | 105 ++++++
.../boards/reflex-achilles/pll-config-arria10.c | 55 ++++
arch/arm/dts/Makefile | 1 +
arch/arm/dts/socfpga_arria10_achilles.dts | 124 ++++++++
arch/arm/mach-socfpga/Kconfig | 5 +
images/Makefile.socfpga | 4 +
10 files changed, 696 insertions(+)
create mode 100644 arch/arm/boards/reflex-achilles/Makefile
create mode 100644 arch/arm/boards/reflex-achilles/hps.xml
create mode 100644 arch/arm/boards/reflex-achilles/lowlevel.c
create mode 100644 arch/arm/boards/reflex-achilles/pinmux-config-arria10.c
create mode 100644 arch/arm/boards/reflex-achilles/pll-config-arria10.c
create mode 100644 arch/arm/dts/socfpga_arria10_achilles.dts
diff --git a/arch/arm/boards/Makefile b/arch/arm/boards/Makefile
index 250ccb88896f..bcd94a05694e 100644
--- a/arch/arm/boards/Makefile
+++ b/arch/arm/boards/Makefile
@@ -110,6 +110,7 @@ obj-$(CONFIG_MACH_SAMA5D4EK) += sama5d4ek/
obj-$(CONFIG_MACH_SCB9328) += scb9328/
obj-$(CONFIG_MACH_SOCFPGA_ALTERA_SOCDK) += altera-socdk/
obj-$(CONFIG_MACH_SOCFPGA_EBV_SOCRATES) += ebv-socrates/
+obj-$(CONFIG_MACH_SOCFPGA_REFLEX_ACHILLES) += reflex-achilles/
obj-$(CONFIG_MACH_SOCFPGA_TERASIC_DE0_NANO_SOC) += terasic-de0-nano-soc/
obj-$(CONFIG_MACH_SOCFPGA_TERASIC_SOCKIT) += terasic-sockit/
obj-$(CONFIG_MACH_SOLIDRUN_CUBOX) += solidrun-cubox/
diff --git a/arch/arm/boards/reflex-achilles/Makefile b/arch/arm/boards/reflex-achilles/Makefile
new file mode 100644
index 000000000000..6b4214115300
--- /dev/null
+++ b/arch/arm/boards/reflex-achilles/Makefile
@@ -0,0 +1,2 @@
+obj-y += lowlevel.o
+pbl-y += lowlevel.o
diff --git a/arch/arm/boards/reflex-achilles/hps.xml b/arch/arm/boards/reflex-achilles/hps.xml
new file mode 100644
index 000000000000..d719ca00587c
--- /dev/null
+++ b/arch/arm/boards/reflex-achilles/hps.xml
@@ -0,0 +1,351 @@
+<hps>
+ <system>
+ <config name='VERSION' value='16.1' />
+ <config name='DEVICE_FAMILY' value='Arria 10' />
+ <config name='TIME_AND_DATE' value='Tuesday December, 06, 2016 - 03:45:21 PM CET' />
+ <config name='DMA_Enable' value='No No No No No No No No' />
+ <config name='eosc1_clk_hz' value='25000000.0' />
+ <config name='emac0_clk_hz' value='250000000' />
+ <config name='emac1_clk_hz' value='250000000' />
+ <config name='emac2_clk_hz' value='250000000' />
+ <config name='sdmmc_clk_hz' value='200000000' />
+ <config name='l3_main_free_clk_hz' value='400000000' />
+ <config name='h2f_user0_clk_hz' value='100000000' />
+ <config name='h2f_user1_clk_hz' value='100000000' />
+ <config name='tpiu_clk_hz' value='100000000' />
+ <config name='f2h_free_clk_hz' value='200000000' />
+ <config name='cb_intosc_ls_clk_hz' value='60000000' />
+ </system>
+ <fpga_interfaces>
+ <config name='F2H_AXI_SLAVE' used='false' />
+ <config name='H2F_AXI_MASTER' used='false' />
+ <config name='LWH2F_AXI_MASTER' used='true' />
+ <config name='F2SDRAM0_AXI_SLAVE' used='false' />
+ <config name='F2SDRAM1_AXI_SLAVE' used='false' />
+ <config name='F2SDRAM2_AXI_SLAVE' used='false' />
+ </fpga_interfaces>
+ <peripherals>
+ <peripheral name='rgmii0' used='false' />
+ <peripheral name='rgmii1' used='true' />
+ <peripheral name='rgmii2' used='true' />
+ <peripheral name='nand' used='false' />
+ <peripheral name='qspi' used='false'>
+ <config name='CONFIG_HPS_QSPI_CS2' value='0' />
+ <config name='CONFIG_HPS_QSPI_CS3' value='0' />
+ <config name='CONFIG_HPS_QSPI_CS4' value='0' />
+ <config name='CONFIG_HPS_QSPI_CS0' value='0' />
+ <config name='CONFIG_HPS_QSPI_CS1' value='0' />
+ </peripheral>
+ <peripheral name='sdmmc' used='true'>
+ <config name='CONFIG_HPS_SDMMC_BUSWIDTH' value='8' />
+ </peripheral>
+ <peripheral name='usb0' used='false' />
+ <peripheral name='usb1' used='true' />
+ <peripheral name='spim0' used='true' />
+ <peripheral name='spim1' used='false' />
+ <peripheral name='spis0' used='false' />
+ <peripheral name='spis1' used='false' />
+ <peripheral name='uart0' used='true'>
+ <config name='CONFIG_HPS_UART0_TX' value='1' />
+ <config name='CONFIG_HPS_UART0_RTS' value='1' />
+ <config name='CONFIG_HPS_UART0_CTS' value='1' />
+ <config name='CONFIG_HPS_UART0_RX' value='1' />
+ </peripheral>
+ <peripheral name='uart1' used='false'>
+ <config name='CONFIG_HPS_UART1_TX' value='0' />
+ <config name='CONFIG_HPS_UART1_RTS' value='0' />
+ <config name='CONFIG_HPS_UART1_CTS' value='0' />
+ <config name='CONFIG_HPS_UART1_RX' value='0' />
+ </peripheral>
+ <peripheral name='i2c0' used='true' />
+ <peripheral name='i2c1' used='false' />
+ <peripheral name='i2cemac0' used='false' />
+ <peripheral name='i2cemac1' used='false' />
+ <peripheral name='i2cemac2' used='false' />
+ <peripheral name='trace' used='false' />
+ <peripheral name='pll_clock_out' used='false' />
+ </peripherals>
+ <csr>
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q4_12.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q4_11.sel' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.pinmux_dedicated_io_4.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q4_10.sel' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.pinmux_dedicated_io_5.sel' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.pinmux_dedicated_io_6.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q4_9.sel' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.pinmux_dedicated_io_7.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q4_8.sel' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.pinmux_dedicated_io_8.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q4_6.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q4_7.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q4_5.sel' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.pinmux_dedicated_io_9.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q4_4.sel' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.pinmux_dedicated_io_10.sel' value='10' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q4_3.sel' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.pinmux_dedicated_io_11.sel' value='10' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q4_2.sel' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.pinmux_dedicated_io_12.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q4_1.sel' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.pinmux_dedicated_io_13.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q3_12.sel' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.pinmux_dedicated_io_14.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q3_11.sel' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.pinmux_dedicated_io_15.sel' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.pinmux_dedicated_io_16.sel' value='15' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.pinmux_dedicated_io_17.sel' value='15' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q3_10.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q3_8.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q3_9.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q3_7.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q3_6.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q3_5.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q3_4.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q3_3.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q3_2.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q3_1.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q2_12.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q2_10.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q2_11.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q2_9.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q2_8.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q2_7.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q2_6.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q2_5.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q2_4.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q2_3.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q2_2.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q2_1.sel' value='8' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q1_12.sel' value='10' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q1_11.sel' value='10' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q1_10.sel' value='1' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q1_9.sel' value='1' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q1_8.sel' value='1' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q1_7.sel' value='1' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q1_6.sel' value='0' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q1_5.sel' value='0' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q1_4.sel' value='13' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q1_3.sel' value='13' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q1_2.sel' value='13' />
+ <config name='i_io48_pin_mux_shared_3v_io_grp.pinmux_shared_io_q1_1.sel' value='13' />
+ <config name='i_io48_pin_mux_fpga_interface_grp.pinmux_rgmii0_usefpga.sel' value='0' />
+ <config name='i_io48_pin_mux_fpga_interface_grp.pinmux_rgmii1_usefpga.sel' value='0' />
+ <config name='i_io48_pin_mux_fpga_interface_grp.pinmux_rgmii2_usefpga.sel' value='0' />
+ <config name='i_io48_pin_mux_fpga_interface_grp.pinmux_nand_usefpga.sel' value='0' />
+ <config name='i_io48_pin_mux_fpga_interface_grp.pinmux_qspi_usefpga.sel' value='0' />
+ <config name='i_io48_pin_mux_fpga_interface_grp.pinmux_sdmmc_usefpga.sel' value='0' />
+ <config name='i_io48_pin_mux_fpga_interface_grp.pinmux_usb0_usefpga.sel' value='0' />
+ <config name='i_io48_pin_mux_fpga_interface_grp.pinmux_usb1_usefpga.sel' value='0' />
+ <config name='i_io48_pin_mux_fpga_interface_grp.pinmux_spim0_usefpga.sel' value='1' />
+ <config name='i_io48_pin_mux_fpga_interface_grp.pinmux_spim1_usefpga.sel' value='0' />
+ <config name='i_io48_pin_mux_fpga_interface_grp.pinmux_spis0_usefpga.sel' value='0' />
+ <config name='i_io48_pin_mux_fpga_interface_grp.pinmux_spis1_usefpga.sel' value='0' />
+ <config name='i_io48_pin_mux_fpga_interface_grp.pinmux_uart0_usefpga.sel' value='0' />
+ <config name='i_io48_pin_mux_fpga_interface_grp.pinmux_uart1_usefpga.sel' value='0' />
+ <config name='i_io48_pin_mux_fpga_interface_grp.pinmux_i2c0_usefpga.sel' value='0' />
+ <config name='i_io48_pin_mux_fpga_interface_grp.pinmux_i2c1_usefpga.sel' value='0' />
+ <config name='i_io48_pin_mux_fpga_interface_grp.pinmux_i2cemac0_usefpga.sel' value='0' />
+ <config name='i_io48_pin_mux_fpga_interface_grp.pinmux_i2cemac1_usefpga.sel' value='0' />
+ <config name='i_io48_pin_mux_fpga_interface_grp.pinmux_i2cemac2_usefpga.sel' value='0' />
+ <config name='i_io48_pin_mux_fpga_interface_grp.pinmux_pll_clock_out_usefpga.sel' value='0' />
+ <config name='i_clk_mgr_alteragrp.nocclk.maincnt' value='3' />
+ <config name='i_clk_mgr_perpllgrp.vco1.denom' value='1' />
+ <config name='i_clk_mgr_mainpllgrp.cntr8clk.cnt' value='900' />
+ <config name='i_clk_mgr_perpllgrp.emacctl.emac2sel' value='0' />
+ <config name='i_clk_mgr_mainpllgrp.cntr9clk.cnt' value='900' />
+ <config name='i_clk_mgr_mainpllgrp.cntr6clk.cnt' value='7' />
+ <config name='i_clk_mgr_alteragrp.mpuclk.pericnt' value='900' />
+ <config name='i_clk_mgr_alteragrp.mpuclk.maincnt' value='1' />
+ <config name='i_clk_mgr_perpllgrp.cntr3clk.cnt' value='900' />
+ <config name='i_clk_mgr_perpllgrp.cntr6clk.src' value='0' />
+ <config name='i_clk_mgr_mainpllgrp.cntr2clk.cnt' value='900' />
+ <config name='i_clk_mgr_mainpllgrp.nocdiv.l4mpclk' value='2' />
+ <config name='i_clk_mgr_perpllgrp.cntr4clk.src' value='1' />
+ <config name='i_clk_mgr_perpllgrp.emacctl.emac0sel' value='0' />
+ <config name='i_clk_mgr_mainpllgrp.nocclk.cnt' value='0' />
+ <config name='i_clk_mgr_mainpllgrp.nocdiv.l4spclk' value='2' />
+ <config name='i_clk_mgr_perpllgrp.gpiodiv.gpiodbclk' value='32000' />
+ <config name='i_clk_mgr_perpllgrp.cntr3clk.src' value='1' />
+ <config name='i_clk_mgr_perpllgrp.cntr8clk.src' value='0' />
+ <config name='i_clk_mgr_mainpllgrp.vco1.numer' value='127' />
+ <config name='i_clk_mgr_perpllgrp.cntr8clk.cnt' value='900' />
+ <config name='i_clk_mgr_mainpllgrp.nocdiv.csatclk' value='2' />
+ <config name='i_clk_mgr_mainpllgrp.nocdiv.cspdbgclk' value='0' />
+ <config name='i_clk_mgr_mainpllgrp.mpuclk.cnt' value='0' />
+ <config name='i_clk_mgr_perpllgrp.cntr5clk.cnt' value='374' />
+ <config name='i_clk_mgr_perpllgrp.cntr6clk.cnt' value='900' />
+ <config name='i_clk_mgr_perpllgrp.cntr5clk.src' value='1' />
+ <config name='i_clk_mgr_perpllgrp.cntr2clk.src' value='1' />
+ <config name='i_clk_mgr_mainpllgrp.nocdiv.cstraceclk' value='0' />
+ <config name='i_clk_mgr_mainpllgrp.nocdiv.l4mainclk' value='2' />
+ <config name='i_clk_mgr_clkmgr.testioctrl.periclksel' value='8' />
+ <config name='i_clk_mgr_mainpllgrp.cntr7clk.src' value='0' />
+ <config name='i_clk_mgr_mainpllgrp.cntr7clk.cnt' value='900' />
+ <config name='i_clk_mgr_mainpllgrp.mpuclk.src' value='0' />
+ <config name='i_clk_mgr_mainpllgrp.cntr5clk.cnt' value='900' />
+ <config name='i_clk_mgr_mainpllgrp.vco1.denom' value='1' />
+ <config name='i_clk_mgr_mainpllgrp.cntr9clk.src' value='0' />
+ <config name='i_clk_mgr_clkmgr.testioctrl.debugclksel' value='16' />
+ <config name='i_clk_mgr_mainpllgrp.nocclk.src' value='0' />
+ <config name='i_clk_mgr_perpllgrp.cntr2clk.cnt' value='5' />
+ <config name='i_clk_mgr_perpllgrp.emacctl.emac1sel' value='0' />
+ <config name='i_clk_mgr_mainpllgrp.cntr3clk.cnt' value='900' />
+ <config name='i_clk_mgr_perpllgrp.vco0.psrc' value='0' />
+ <config name='i_clk_mgr_mainpllgrp.cntr4clk.cnt' value='900' />
+ <config name='i_clk_mgr_mainpllgrp.cntr15clk.cnt' value='900' />
+ <config name='i_clk_mgr_perpllgrp.vco1.numer' value='119' />
+ <config name='i_clk_mgr_clkmgr.testioctrl.mainclksel' value='8' />
+ <config name='i_clk_mgr_mainpllgrp.vco0.psrc' value='0' />
+ <config name='i_clk_mgr_alteragrp.nocclk.pericnt' value='900' />
+ <config name='i_clk_mgr_perpllgrp.cntr4clk.cnt' value='14' />
+ <config name='i_clk_mgr_perpllgrp.cntr7clk.cnt' value='900' />
+ <config name='i_clk_mgr_perpllgrp.cntr9clk.cnt' value='900' />
+ </csr>
+ <csr />
+ <!-- This section was added by Quartus Prime Version 16.1.0 Build 196 10/24/2016 SJ Standard Edition -->
+ <!-- Generated on Tue Dec 13 10:34:43 2016 -->
+ <csr>
+ <!-- OSC_CLK_1_HPS -->
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_1.rtrim' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_1.input_buf_en' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_1.wk_pu_en' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_1.pu_slw_rt' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_1.pd_slw_rt' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_1.pu_drv_strg' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_1.pd_drv_strg' value='10' />
+ <!-- nPOR_HPS -->
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_2.rtrim' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_2.input_buf_en' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_2.wk_pu_en' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_2.pu_slw_rt' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_2.pd_slw_rt' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_2.pu_drv_strg' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_2.pd_drv_strg' value='10' />
+ <!-- nRST_HPS -->
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_3.rtrim' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_3.input_buf_en' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_3.wk_pu_en' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_3.pu_slw_rt' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_3.pd_slw_rt' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_3.pu_drv_strg' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_3.pd_drv_strg' value='10' />
+ <!-- hps_io_phery_sdmmc_D0, HPS_DEDICATED_4, input, weak pull up disable, is output, Fast Slew, 1_8 -->
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_4.rtrim' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_4.input_buf_en' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_4.wk_pu_en' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_4.pu_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_4.pd_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_4.pu_drv_strg' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_4.pd_drv_strg' value='10' />
+ <!-- hps_io_phery_sdmmc_CMD, HPS_DEDICATED_5, input, weak pull up disable, is output, Fast Slew, 1_8 -->
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_5.rtrim' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_5.input_buf_en' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_5.wk_pu_en' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_5.pu_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_5.pd_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_5.pu_drv_strg' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_5.pd_drv_strg' value='10' />
+ <!-- hps_io_phery_sdmmc_CCLK, BOOTSEL2/HPS_DEDICATED_6, NOT input, weak pull up disable, is output, Fast Slew, 1_8 -->
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_6.rtrim' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_6.input_buf_en' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_6.wk_pu_en' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_6.pu_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_6.pd_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_6.pu_drv_strg' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_6.pd_drv_strg' value='10' />
+ <!-- hps_io_phery_sdmmc_D1, HPS_DEDICATED_7, input, weak pull up disable, is output, Fast Slew, 1_8 -->
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_7.rtrim' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_7.input_buf_en' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_7.wk_pu_en' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_7.pu_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_7.pd_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_7.pu_drv_strg' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_7.pd_drv_strg' value='10' />
+ <!-- hps_io_phery_sdmmc_D2, HPS_DEDICATED_8, input, weak pull up disable, is output, Fast Slew, 1_8 -->
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_8.rtrim' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_8.input_buf_en' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_8.wk_pu_en' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_8.pu_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_8.pd_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_8.pu_drv_strg' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_8.pd_drv_strg' value='10' />
+ <!-- hps_io_phery_sdmmc_D3, HPS_DEDICATED_9, input, weak pull up disable, is output, Fast Slew, 1_8 -->
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_9.rtrim' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_9.input_buf_en' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_9.wk_pu_en' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_9.pu_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_9.pd_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_9.pu_drv_strg' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_9.pd_drv_strg' value='10' />
+ <!-- Unused pin 10 -->
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_10.rtrim' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_10.input_buf_en' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_10.wk_pu_en' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_10.pu_slw_rt' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_10.pd_slw_rt' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_10.pu_drv_strg' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_10.pd_drv_strg' value='0' />
+ <!-- Unused pin 11 -->
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_11.rtrim' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_11.input_buf_en' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_11.wk_pu_en' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_11.pu_slw_rt' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_11.pd_slw_rt' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_11.pu_drv_strg' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_11.pd_drv_strg' value='0' />
+ <!-- hps_io_phery_sdmmc_D4, HPS_DEDICATED_12, input, weak pull up disable, is output, Fast Slew, 1_8 -->
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_12.rtrim' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_12.input_buf_en' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_12.wk_pu_en' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_12.pu_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_12.pd_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_12.pu_drv_strg' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_12.pd_drv_strg' value='10' />
+ <!-- hps_io_phery_sdmmc_D5, HPS_DEDICATED_13, input, weak pull up disable, is output, Fast Slew, 1_8 -->
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_13.rtrim' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_13.input_buf_en' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_13.wk_pu_en' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_13.pu_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_13.pd_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_13.pu_drv_strg' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_13.pd_drv_strg' value='10' />
+ <!-- hps_io_phery_sdmmc_D6, HPS_DEDICATED_14, input, weak pull up disable, is output, Fast Slew, 1_8 -->
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_14.rtrim' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_14.input_buf_en' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_14.wk_pu_en' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_14.pu_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_14.pd_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_14.pu_drv_strg' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_14.pd_drv_strg' value='10' />
+ <!-- hps_io_phery_sdmmc_D7, HPS_DEDICATED_15, input, weak pull up disable, is output, Fast Slew, 1_8 -->
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_15.rtrim' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_15.input_buf_en' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_15.wk_pu_en' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_15.pu_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_15.pd_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_15.pu_drv_strg' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_15.pd_drv_strg' value='10' />
+ <!-- hps_usr_led_g, HPS_DEDICATED_16, input, weak pull up disable, is output, Fast Slew, 1_8 -->
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_16.rtrim' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_16.input_buf_en' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_16.wk_pu_en' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_16.pu_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_16.pd_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_16.pu_drv_strg' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_16.pd_drv_strg' value='10' />
+ <!-- hps_usr_led_r, HPS_DEDICATED_17, input, weak pull up disable, is output, Fast Slew, 1_8 -->
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_17.rtrim' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_17.input_buf_en' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_17.wk_pu_en' value='0' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_17.pu_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_17.pd_slw_rt' value='1' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_17.pu_drv_strg' value='8' />
+ <config name='i_io48_pin_mux_dedicated_io_grp.configuration_dedicated_io_17.pd_drv_strg' value='10' />
+ <config name='i_io48_pin_mux.configuration_dedicated_io_bank.voltage_sel_clkrst_io' value='1' />
+ <config name='i_io48_pin_mux.configuration_dedicated_io_bank.voltage_sel_peri_io' value='1' />
+ </csr>
+ <option_flags>
+ <config name='chosen.early-release-fpga-config' value='0' />
+ </option_flags>
+ <!-- End of the section generated by Quartus Prime -->
+</hps>
diff --git a/arch/arm/boards/reflex-achilles/lowlevel.c b/arch/arm/boards/reflex-achilles/lowlevel.c
new file mode 100644
index 000000000000..52ecb919e5a2
--- /dev/null
+++ b/arch/arm/boards/reflex-achilles/lowlevel.c
@@ -0,0 +1,48 @@
+#include <common.h>
+#include <linux/sizes.h>
+#include <io.h>
+#include <asm/barebox-arm-head.h>
+#include <asm/barebox-arm.h>
+#include <asm/cache.h>
+#include <debug_ll.h>
+#include <mach/arria10-sdram.h>
+#include <mach/arria10-regs.h>
+#include <mach/arria10-reset-manager.h>
+#include <mach/arria10-clock-manager.h>
+#include <mach/arria10-pinmux.h>
+#include "pll-config-arria10.c"
+#include "pinmux-config-arria10.c"
+#include <mach/generic.h>
+
+extern char __dtb_socfpga_arria10_achilles_start[];
+
+static noinline void achilles_entry(void)
+{
+ void *fdt;
+
+ arm_early_mmu_cache_invalidate();
+
+ relocate_to_current_adr();
+ setup_c();
+
+ arria10_init(&mainpll_cfg, &perpll_cfg, &pinmux);
+
+ puts_ll("lowlevel init done\n");
+
+ arria10_ddr_calibration_sequence();
+
+ puts_ll("SDRAM setup done\n");
+
+ fdt = __dtb_socfpga_arria10_achilles_start - get_runtime_offset();
+
+ barebox_arm_entry(0x0, SZ_2G + SZ_1G, fdt);
+}
+
+ENTRY_FUNCTION(start_socfpga_achilles, r0, r1, r2)
+{
+ arm_cpu_lowlevel_init();
+
+ arm_setup_stack(0xffe00000 + SZ_256K - SZ_32K - SZ_4K - 16);
+
+ achilles_entry();
+}
diff --git a/arch/arm/boards/reflex-achilles/pinmux-config-arria10.c b/arch/arm/boards/reflex-achilles/pinmux-config-arria10.c
new file mode 100644
index 000000000000..58b1a1ebc1fd
--- /dev/null
+++ b/arch/arm/boards/reflex-achilles/pinmux-config-arria10.c
@@ -0,0 +1,105 @@
+#include <mach/arria10-pinmux.h>
+
+static struct arria10_pinmux_cfg pinmux = {
+.shared_io_q4_12=8,
+.shared_io_q4_11=8,
+.shared_io_q4_10=8,
+.shared_io_q4_9=8,
+.shared_io_q4_8=8,
+.shared_io_q4_6=8,
+.shared_io_q4_7=8,
+.shared_io_q4_5=8,
+.shared_io_q4_4=8,
+.shared_io_q4_3=8,
+.shared_io_q4_2=8,
+.shared_io_q4_1=8,
+.shared_io_q3_12=8,
+.shared_io_q3_11=8,
+.shared_io_q3_10=8,
+.shared_io_q3_8=8,
+.shared_io_q3_9=8,
+.shared_io_q3_7=8,
+.shared_io_q3_6=8,
+.shared_io_q3_5=8,
+.shared_io_q3_4=8,
+.shared_io_q3_3=8,
+.shared_io_q3_2=8,
+.shared_io_q3_1=8,
+.shared_io_q2_12=8,
+.shared_io_q2_10=8,
+.shared_io_q2_11=8,
+.shared_io_q2_9=8,
+.shared_io_q2_8=8,
+.shared_io_q2_7=8,
+.shared_io_q2_6=8,
+.shared_io_q2_5=8,
+.shared_io_q2_4=8,
+.shared_io_q2_3=8,
+.shared_io_q2_2=8,
+.shared_io_q2_1=8,
+.shared_io_q1_12=10,
+.shared_io_q1_11=10,
+.shared_io_q1_10=1,
+.shared_io_q1_9=1,
+.shared_io_q1_8=1,
+.shared_io_q1_7=1,
+.shared_io_q1_6=0,
+.shared_io_q1_5=0,
+.shared_io_q1_4=13,
+.shared_io_q1_3=13,
+.shared_io_q1_2=13,
+.shared_io_q1_1=13,
+.dedicated_io_4=8,
+.dedicated_io_5=8,
+.dedicated_io_6=8,
+.dedicated_io_7=8,
+.dedicated_io_8=8,
+.dedicated_io_9=8,
+.dedicated_io_10=10,
+.dedicated_io_11=10,
+.dedicated_io_12=8,
+.dedicated_io_13=8,
+.dedicated_io_14=8,
+.dedicated_io_15=8,
+.dedicated_io_16=15,
+.dedicated_io_17=15,
+.cfg_dedicated_io_bank=0x00000101,
+.cfg_dedicated_io_1=0x000b080a,
+.cfg_dedicated_io_2=0x000b080a,
+.cfg_dedicated_io_3=0x000b080a,
+.cfg_dedicated_io_4=0x000a282a,
+.cfg_dedicated_io_5=0x000a282a,
+.cfg_dedicated_io_6=0x000a282a,
+.cfg_dedicated_io_7=0x000a282a,
+.cfg_dedicated_io_8=0x000a282a,
+.cfg_dedicated_io_9=0x000a282a,
+.cfg_dedicated_io_10=0x00090000,
+.cfg_dedicated_io_11=0x00090000,
+.cfg_dedicated_io_12=0x000a282a,
+.cfg_dedicated_io_13=0x000a282a,
+.cfg_dedicated_io_14=0x000a282a,
+.cfg_dedicated_io_15=0x000a282a,
+.cfg_dedicated_io_16=0x000a282a,
+.cfg_dedicated_io_17=0x000a282a,
+.rgmii0_usefpga=0,
+.rgmii1_usefpga=0,
+.rgmii2_usefpga=0,
+.nand_usefpga=0,
+.qspi_usefpga=0,
+.sdmmc_usefpga=0,
+.usb0_usefpga=0,
+.usb1_usefpga=0,
+.spim0_usefpga=1,
+.spim1_usefpga=0,
+.spis0_usefpga=0,
+.spis1_usefpga=0,
+.uart0_usefpga=0,
+.uart1_usefpga=0,
+.i2c0_usefpga=0,
+.i2c1_usefpga=0,
+.i2cemac0_usefpga=0,
+.i2cemac1_usefpga=0,
+.i2cemac2_usefpga=0,
+.pll_clock_out_usefpga=0,
+};
+
diff --git a/arch/arm/boards/reflex-achilles/pll-config-arria10.c b/arch/arm/boards/reflex-achilles/pll-config-arria10.c
new file mode 100644
index 000000000000..f4b10c956a22
--- /dev/null
+++ b/arch/arm/boards/reflex-achilles/pll-config-arria10.c
@@ -0,0 +1,55 @@
+#include <mach/arria10-clock-manager.h>
+
+static struct arria10_mainpll_cfg mainpll_cfg = {
+ .vco0_psrc = 0,
+ .vco1_numer = 127,
+ .vco1_denom = 1,
+ .mpuclk_cnt = 0,
+ .mpuclk_src = 0,
+ .nocclk_cnt = 0,
+ .nocclk_src = 0,
+ .cntr2clk_cnt = 900,
+ .cntr3clk_cnt = 900,
+ .cntr4clk_cnt = 900,
+ .cntr5clk_cnt = 900,
+ .cntr6clk_cnt = 7,
+ .cntr7clk_cnt = 900,
+ .cntr7clk_src = 0,
+ .cntr8clk_cnt = 900,
+ .cntr9clk_cnt = 900,
+ .cntr9clk_src = 0,
+ .cntr15clk_cnt = 900,
+ .nocdiv_l4mainclk = 2,
+ .nocdiv_l4mpclk = 2,
+ .nocdiv_l4spclk = 2,
+ .nocdiv_csatclk = 2,
+ .nocdiv_cstraceclk = 0,
+ .nocdiv_cspdbgclk = 0,
+ .mpuclk = 0x3840001,
+ .nocclk = 0x3840003,
+};
+
+static struct arria10_perpll_cfg perpll_cfg = {
+ .vco0_psrc = 0,
+ .vco1_denom = 1,
+ .vco1_numer = 119,
+ .cntr2clk_cnt = 5,
+ .cntr2clk_src = 1,
+ .cntr3clk_cnt = 900,
+ .cntr3clk_src = 1,
+ .cntr4clk_cnt = 14,
+ .cntr4clk_src = 1,
+ .cntr5clk_cnt = 374,
+ .cntr5clk_src = 1,
+ .cntr6clk_cnt = 900,
+ .cntr6clk_src = 0,
+ .cntr7clk_cnt = 900,
+ .cntr8clk_cnt = 900,
+ .cntr8clk_src = 0,
+ .cntr9clk_cnt = 900,
+ .cntr9clk_src = 0,
+ .emacctl_emac0sel = 0,
+ .emacctl_emac1sel = 0,
+ .emacctl_emac2sel = 0,
+ .gpiodiv_gpiodbclk = 32000,
+};
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 70359d8242a5..68fa18055a78 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -63,6 +63,7 @@ pbl-dtb-$(CONFIG_MACH_SABRESD) += imx6q-sabresd.dtb.o
pbl-dtb-$(CONFIG_MACH_FREESCALE_IMX6SX_SABRESDB) += imx6sx-sdb.dtb.o
pbl-dtb-$(CONFIG_MACH_SOCFPGA_ALTERA_SOCDK) += socfpga_cyclone5_socdk.dtb.o
pbl-dtb-$(CONFIG_MACH_SOCFPGA_EBV_SOCRATES) += socfpga_cyclone5_socrates.dtb.o
+pbl-dtb-$(CONFIG_MACH_SOCFPGA_REFLEX_ACHILLES) += socfpga_arria10_achilles.dtb.o
pbl-dtb-$(CONFIG_MACH_SOCFPGA_TERASIC_DE0_NANO_SOC) += socfpga_cyclone5_de0_nano_soc.dtb.o
pbl-dtb-$(CONFIG_MACH_SOCFPGA_TERASIC_SOCKIT) += socfpga_cyclone5_sockit.dtb.o
pbl-dtb-$(CONFIG_MACH_SOLIDRUN_CUBOX) += dove-cubox-bb.dtb.o
diff --git a/arch/arm/dts/socfpga_arria10_achilles.dts b/arch/arm/dts/socfpga_arria10_achilles.dts
new file mode 100644
index 000000000000..dd991318e249
--- /dev/null
+++ b/arch/arm/dts/socfpga_arria10_achilles.dts
@@ -0,0 +1,124 @@
+/*
+ * Copyright (C) 2015 Altera Corporation <www.altera.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+/dts-v1/;
+#include <arm/socfpga_arria10.dtsi>
+
+/ {
+ model = "Reflex SOCFPGA Arria 10 Achilles";
+ compatible = "reflex,achilles", "altr,socfpga-arria10", "altr,socfpga";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ linux,stdout-path = &uart0;
+
+ environment@0 {
+ compatible = "barebox,environment";
+ device-path = &mmc, "partname:1";
+ file-path = "barebox.env";
+ };
+ };
+
+ memory {
+ name = "memory";
+ device_type = "memory";
+ reg = <0x0 0xc0000000>;
+ };
+
+ soc {
+ clkmgr@ffd04000 {
+ clocks {
+ osc1 {
+ clock-frequency = <25000000>;
+ };
+
+ cb_intosc_hs_div2_clk {
+ clock-frequency = <0>;
+ };
+ cb_intosc_ls_clk {
+ clock-frequency = <60000000>;
+ };
+ f2s_free_clk {
+ clock-frequency = <200000000>;
+ };
+ };
+ };
+ };
+};
+
+&gmac1 {
+ phy-mode = "rgmii";
+ phy-addr = <0x00fffff0>; /* probe for phy addr */
+
+ /*
+ * These skews assume the user's FPGA design is adding 600ps of delay
+ * for TX_CLK on Arria 10.
+ *
+ * All skews are offset since hardware skew values for the ksz9031
+ * range from a negative skew to a positive skew.
+ * See the micrel-ksz90x1.txt Documentation file for details.
+ */
+ txd0-skew-ps = <0>; /* -420ps */
+ txd1-skew-ps = <0>; /* -420ps */
+ txd2-skew-ps = <0>; /* -420ps */
+ txd3-skew-ps = <0>; /* -420ps */
+ rxd0-skew-ps = <420>; /* 0ps */
+ rxd1-skew-ps = <420>; /* 0ps */
+ rxd2-skew-ps = <420>; /* 0ps */
+ rxd3-skew-ps = <420>; /* 0ps */
+ txen-skew-ps = <0>; /* -420ps */
+ txc-skew-ps = <1860>; /* 960ps */
+ rxdv-skew-ps = <420>; /* 0ps */
+ rxc-skew-ps = <1680>; /* 780ps */
+ max-frame-size = <3800>;
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ tempsensor: ti,tmp102@0x48 {
+ compatible = "ti,tmp102";
+ reg = <0x48>;
+ };
+
+ rtc: nxp,pcf8563@0x51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+
+ eeprom: at24@0x54 {
+ compatible = "at24";
+ reg = <0x54>;
+ bytelen = <256>;
+ pagesize = <16>;
+ };
+};
+
+&mmc {
+ supports-highspeed;
+ broken-cd;
+ bus-width = <1>;
+ status = "okay";
+};
+
+&uart0 {
+ reg-io-width = <4>;
+ status = "okay";
+};
diff --git a/arch/arm/mach-socfpga/Kconfig b/arch/arm/mach-socfpga/Kconfig
index 003574ba8d65..9bdcd7fec56f 100644
--- a/arch/arm/mach-socfpga/Kconfig
+++ b/arch/arm/mach-socfpga/Kconfig
@@ -32,6 +32,11 @@ config MACH_SOCFPGA_EBV_SOCRATES
select ARCH_SOCFPGA_CYCLONE5
bool "EBV Socrates"
+config MACH_SOCFPGA_REFLEX_ACHILLES
+ select HAVE_DEFAULT_ENVIRONMENT_NEW
+ select ARCH_SOCFPGA_ARRIA10
+ bool "Reflex Achilles"
+
config MACH_SOCFPGA_TERASIC_DE0_NANO_SOC
select HAVE_DEFAULT_ENVIRONMENT_NEW
select ARCH_SOCFPGA_CYCLONE5
diff --git a/images/Makefile.socfpga b/images/Makefile.socfpga
index d210a6cc2318..2d4b91dada3c 100644
--- a/images/Makefile.socfpga
+++ b/images/Makefile.socfpga
@@ -35,6 +35,10 @@ pblx-$(CONFIG_MACH_SOCFPGA_TERASIC_DE0_NANO_SOC) += start_socfpga_de0_nano_soc
FILE_barebox-socfpga-de0_nano_soc.img = start_socfpga_de0_nano_soc.pblx
socfpga-barebox-$(CONFIG_MACH_SOCFPGA_TERASIC_DE0_NANO_SOC) += barebox-socfpga-de0_nano_soc.img
+pblx-$(CONFIG_MACH_SOCFPGA_REFLEX_ACHILLES) += start_socfpga_achilles
+FILE_barebox-socfpga-achilles.img = start_socfpga_achilles.pblx.socfpgaimg
+socfpga-barebox-$(CONFIG_MACH_SOCFPGA_REFLEX_ACHILLES) += barebox-socfpga-achilles.img
+
pblx-$(CONFIG_MACH_SOCFPGA_TERASIC_SOCKIT) += start_socfpga_sockit_xload
FILE_barebox-socfpga-sockit-xload.img = start_socfpga_sockit_xload.pblx.socfpgaimg
socfpga-xload-$(CONFIG_MACH_SOCFPGA_TERASIC_SOCKIT) += barebox-socfpga-sockit-xload.img
--
2.11.0
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 12+ messages in thread