mail archive of the barebox mailing list
 help / color / mirror / Atom feed
From: Hubert Feurstein <h.feurstein@gmail.com>
To: franck.jullien@gmail.com
Cc: barebox@lists.infradead.org
Subject: Re: [PATCH] [RFC] nor: Add SPI flash chips driver
Date: Sun, 31 Jul 2011 17:46:34 +0200	[thread overview]
Message-ID: <CAFfN3gUyF-ptBO7y4P2pufYoVrF=eArZaQT5JFEgC3S3Otjw=Q@mail.gmail.com> (raw)
In-Reply-To: <1312057472-31809-1-git-send-email-franck.jullien@gmail.com>

Hi Franck,

please fix the errors reported by ./scripts/checkpatch.pl.

Regards
Hubert

2011/7/30  <franck.jullien@gmail.com>:
> From: Franck Jullien <franck.jullien@gmail.com>
>
> This patch adds the m25p80 driver. It has been ported from
> Linux. MTD code has been removed. It has been tested with
> a m25p40 chip and the Altera SPI master driver.
>
> This driver has been placed in drivers/nor and CFI config
> has been moved to a submenu in Kconfig. Should I create a CFI
> folder in drivers/nor ?
>
> Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
> ---
>  drivers/nor/Kconfig  |   41 +++-
>  drivers/nor/Makefile |    1 +
>  drivers/nor/m25p80.c |  829 ++++++++++++++++++++++++++++++++++++++++++++++++++
>  drivers/nor/m25p80.h |   90 ++++++
>  include/spi/flash.h  |   30 ++
>  5 files changed, 986 insertions(+), 5 deletions(-)
>  create mode 100644 drivers/nor/m25p80.c
>  create mode 100644 drivers/nor/m25p80.h
>  create mode 100644 include/spi/flash.h
>
> diff --git a/drivers/nor/Kconfig b/drivers/nor/Kconfig
> index 43a6b84..84ce0d0 100644
> --- a/drivers/nor/Kconfig
> +++ b/drivers/nor/Kconfig
> @@ -1,14 +1,16 @@
>  menu "flash drivers                 "
>
> -config HAS_CFI
> -       bool
> -
> -config DRIVER_CFI
> -       bool "cfi flash driver"
> +menuconfig DRIVER_CFI
> +       bool "CFI            "
>        help
>          If you have NOR Flash devices connected to your system and wish
>          to use them say yes here.
>
> +if DRIVER_CFI
> +
> +config HAS_CFI
> +       bool
> +
>  config DRIVER_CFI_INTEL
>        default y
>        depends on DRIVER_CFI
> @@ -55,4 +57,33 @@ config CFI_BUFFER_WRITE
>        bool "use cfi driver with buffer write"
>        depends on DRIVER_CFI || DRIVER_CFI
>
> +endif
> +
> +config MTD_M25P80
> +       tristate "SPI Flash chips (AT26DF, M25P, W25X, ...)"
> +       depends on SPI
> +       help
> +         This enables access to most modern SPI flash chips, used for
> +         program and data storage.   Series supported include Atmel AT26DF,
> +         Spansion S25SL, SST 25VF, ST M25P, and Winbond W25X.  Other chips
> +         are supported as well.  See the driver source for the current list,
> +         or to add other chips.
> +
> +         Note that the original DataFlash chips (AT45 series, not AT26DF),
> +         need an entirely different driver.
> +
> +         Set up your spi devices with the right board-specific platform data,
> +         if you want to specify device partitioning or to use a device which
> +         doesn't support the JEDEC ID instruction.
> +
> +config MTD_SST25L
> +       tristate "Support SST25L (non JEDEC) SPI Flash chips"
> +       depends on MTD_M25P80
> +       help
> +         This enables access to the non JEDEC SST25L SPI flash chips, used
> +         for program and data storage.
> +
> +         Set up your spi devices with the right board-specific platform data,
> +         if you want to specify device partitioning.
> +
>  endmenu
> diff --git a/drivers/nor/Makefile b/drivers/nor/Makefile
> index d255043..d676c55 100644
> --- a/drivers/nor/Makefile
> +++ b/drivers/nor/Makefile
> @@ -1,4 +1,5 @@
>  obj-$(CONFIG_DRIVER_CFI) += cfi_flash.o
>  obj-$(CONFIG_DRIVER_CFI_INTEL) += cfi_flash_intel.o
>  obj-$(CONFIG_DRIVER_CFI_AMD) += cfi_flash_amd.o
> +obj-$(CONFIG_MTD_M25P80) += m25p80.o
>
> diff --git a/drivers/nor/m25p80.c b/drivers/nor/m25p80.c
> new file mode 100644
> index 0000000..9c57f16
> --- /dev/null
> +++ b/drivers/nor/m25p80.c
> @@ -0,0 +1,829 @@
> +/*
> + * MTD SPI driver for ST M25Pxx (and similar) serial flash chips
> + *
> + * Author: Mike Lavender, mike@steroidmicros.com
> + * Adapted to barebox :  Franck JULLIEN <elec4fun@gmail.com>
> + *
> + * Copyright (c) 2005, Intec Automation Inc.
> + *
> + * Some parts are based on lart.c by Abraham Van Der Merwe
> + *
> + * Cleaned up and generalized based on mtd_dataflash.c
> + *
> + * This code is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + */
> +
> +#include <common.h>
> +#include <init.h>
> +#include <driver.h>
> +#include <spi/spi.h>
> +#include <spi/flash.h>
> +#include <xfuncs.h>
> +#include <malloc.h>
> +#include <errno.h>
> +#include <linux/err.h>
> +#include <clock.h>
> +#include <linux/mtd/mtd.h>
> +#include <progress.h>
> +#include "m25p80.h"
> +
> +/****************************************************************************/
> +
> +/*
> + * Internal helper functions
> + */
> +
> +/*
> + * Read the status register, returning its value in the location
> + * Return the status register value.
> + * Returns negative if error occurred.
> + */
> +static int read_sr(struct m25p *flash)
> +{
> +       ssize_t retval;
> +       u8 code = OPCODE_RDSR;
> +       u8 val;
> +
> +       retval = spi_write_then_read(flash->spi, &code, 1, &val, 1);
> +
> +       if (retval < 0) {
> +               dev_err(&flash->spi->dev, "error %d reading SR\n",
> +                               (int) retval);
> +               return retval;
> +       }
> +
> +       return val;
> +}
> +
> +/*
> + * Write status register 1 byte
> + * Returns negative if error occurred.
> + */
> +static int write_sr(struct m25p *flash, u8 val)
> +{
> +       flash->command[0] = OPCODE_WRSR;
> +       flash->command[1] = val;
> +
> +       return spi_write(flash->spi, flash->command, 2);
> +}
> +
> +/*
> + * Set write enable latch with Write Enable command.
> + * Returns negative if error occurred.
> + */
> +static inline int write_enable(struct m25p *flash)
> +{
> +       u8      code = OPCODE_WREN;
> +
> +       return spi_write_then_read(flash->spi, &code, 1, NULL, 0);
> +}
> +
> +/*
> + * Send write disble instruction to the chip.
> + */
> +static inline int write_disable(struct m25p *flash)
> +{
> +       u8      code = OPCODE_WRDI;
> +
> +       return spi_write_then_read(flash->spi, &code, 1, NULL, 0);
> +}
> +
> +/*
> + * Enable/disable 4-byte addressing mode.
> + */
> +static inline int set_4byte(struct m25p *flash, int enable)
> +{
> +       u8      code = enable ? OPCODE_EN4B : OPCODE_EX4B;
> +
> +       return spi_write_then_read(flash->spi, &code, 1, NULL, 0);
> +}
> +
> +/*
> + * Service routine to read status register until ready, or timeout occurs.
> + * Returns non-zero if error.
> + */
> +static int wait_till_ready(struct m25p *flash)
> +{
> +       int sr;
> +       uint64_t timer_start;
> +
> +       timer_start = get_time_ns();
> +
> +       do {
> +               if ((sr = read_sr(flash)) < 0)
> +                       break;
> +               else if (!(sr & SR_WIP))
> +                       return 0;
> +
> +       } while (!(is_timeout(timer_start, MAX_READY_WAIT * SECOND)));
> +
> +       return 1;
> +}
> +
> +/*
> + * Erase the whole flash memory
> + *
> + * Returns 0 if successful, non-zero otherwise.
> + */
> +static int erase_chip(struct m25p *flash)
> +{
> +       debug("%s: %s %lldKiB\n",
> +               dev_name(&flash->spi->dev), __func__,
> +               (long long)(flash->size >> 10));
> +
> +       /* Wait until finished previous write command. */
> +       if (wait_till_ready(flash))
> +               return 1;
> +
> +       /* Send write enable, then erase commands. */
> +       write_enable(flash);
> +
> +       /* Set up command buffer. */
> +       flash->command[0] = OPCODE_CHIP_ERASE;
> +
> +       spi_write(flash->spi, flash->command, 1);
> +
> +       return 0;
> +}
> +
> +static void m25p_addr2cmd(struct m25p *flash, unsigned int addr, u8 *cmd)
> +{
> +       /* opcode is in cmd[0] */
> +       cmd[1] = addr >> (flash->addr_width * 8 -  8);
> +       cmd[2] = addr >> (flash->addr_width * 8 - 16);
> +       cmd[3] = addr >> (flash->addr_width * 8 - 24);
> +       cmd[4] = addr >> (flash->addr_width * 8 - 32);
> +}
> +
> +static int m25p_cmdsz(struct m25p *flash)
> +{
> +       return 1 + flash->addr_width;
> +}
> +
> +/*
> + * Erase one sector of flash memory at offset ``offset'' which is any
> + * address within the sector which should be erased.
> + *
> + * Returns 0 if successful, non-zero otherwise.
> + */
> +static int erase_sector(struct m25p *flash, u32 offset)
> +{
> +       debug("%s: %s %dKiB at 0x%08x\n",
> +               dev_name(&flash->spi->dev), __func__,
> +               flash->erasesize / 1024, offset);
> +
> +       /* Wait until finished previous write command. */
> +       if (wait_till_ready(flash))
> +               return 1;
> +
> +       /* Send write enable, then erase commands. */
> +       write_enable(flash);
> +
> +       /* Set up command buffer. */
> +       flash->command[0] = flash->erase_opcode;
> +       m25p_addr2cmd(flash, offset, flash->command);
> +
> +       spi_write(flash->spi, flash->command, m25p_cmdsz(flash));
> +
> +       return 0;
> +}
> +
> +/*
> + * Erase an address range on the flash chip.  The address range may extend
> + * one or more erase sectors.  Return an error is there is a problem erasing.
> + */
> +static ssize_t m25p80_erase(struct cdev *cdev, size_t count, unsigned long offset)
> +{
> +       struct m25p *flash = cdev->priv;
> +       u32 addr, len;
> +       u32 start_sector;
> +       u32 end_sector;
> +       u32 progress = 0;
> +
> +       debug("%s: %s %s 0x%llx, len %lld\n",
> +               dev_name(&flash->spi->dev), __func__, "at",
> +             (long long)offset, (long long)count);
> +
> +       /* sanity checks */
> +       if (offset + count > flash->size)
> +               return -EINVAL;
> +
> +       addr = offset;
> +       len = count;
> +
> +       start_sector = offset / flash->erasesize;
> +       end_sector = (offset + count - 1) / flash->erasesize;
> +       init_progression_bar(end_sector - start_sector);
> +
> +       /* whole-chip erase? */
> +       if (len == flash->size) {
> +
> +               show_progress(start_sector);
> +               if (erase_chip(flash))
> +                       return -EIO;
> +               show_progress(end_sector);
> +
> +       /* REVISIT in some cases we could speed up erasing large regions
> +        * by using OPCODE_SE instead of OPCODE_BE_4K.  We may have set up
> +        * to use "small sector erase", but that's not always optimal.
> +        */
> +
> +       /* "sector"-at-a-time erase */
> +       } else {
> +               while (len) {
> +                       if (erase_sector(flash, addr))
> +                               return -EIO;
> +
> +                       addr += flash->erasesize;
> +                       len -= flash->erasesize;
> +                       show_progress(progress++);
> +               }
> +       }
> +
> +       printf("\n");
> +
> +       return 0;
> +}
> +
> +ssize_t m25p80_read(struct cdev *cdev, void *buf, size_t count, ulong offset, ulong flags)
> +{
> +       struct m25p *flash = cdev->priv;
> +       struct spi_transfer t[2];
> +       struct spi_message m;
> +       ssize_t retlen;
> +
> +       /* sanity checks */
> +       if (!count)
> +               return 0;
> +
> +       if (offset + count > flash->size)
> +               return -EINVAL;
> +
> +       spi_message_init(&m);
> +       memset(t, 0, (sizeof t));
> +
> +       /* NOTE:
> +        * OPCODE_FAST_READ (if available) is faster.
> +        * Should add 1 byte DUMMY_BYTE.
> +        */
> +       t[0].tx_buf = flash->command;
> +       t[0].len = m25p_cmdsz(flash) + FAST_READ_DUMMY_BYTE;
> +       spi_message_add_tail(&t[0], &m);
> +
> +       t[1].rx_buf = buf;
> +       t[1].len = count;
> +       spi_message_add_tail(&t[1], &m);
> +
> +       /* Byte count starts at zero. */
> +       retlen = 0;
> +
> +       /* Wait till previous write/erase is done. */
> +       if (wait_till_ready(flash))
> +               return -ETIME;
> +
> +       /* FIXME switch to OPCODE_FAST_READ.  It's required for higher
> +        * clocks; and at this writing, every chip this driver handles
> +        * supports that opcode.
> +        */
> +
> +       /* Set up the write data buffer. */
> +       flash->command[0] = OPCODE_READ;
> +       m25p_addr2cmd(flash, offset, flash->command);
> +
> +       spi_sync(flash->spi, &m);
> +
> +       retlen = m.actual_length - m25p_cmdsz(flash) - FAST_READ_DUMMY_BYTE;
> +
> +       return retlen;
> +}
> +
> +ssize_t m25p80_write(struct cdev *cdev, const void *buf, size_t count, ulong offset, ulong flags)
> +{
> +       struct m25p *flash = cdev->priv;
> +       struct spi_transfer t[2];
> +       struct spi_message m;
> +       ssize_t retlen = 0;
> +       u32 page_offset, page_size;
> +
> +       debug("m25p80_write %ld bytes at 0x%08lX\n", (unsigned long)count, offset);
> +
> +       if (offset + count > flash->size)
> +               return -EINVAL;
> +
> +       spi_message_init(&m);
> +       memset(t, 0, (sizeof t));
> +
> +       t[0].tx_buf = flash->command;
> +       t[0].len = m25p_cmdsz(flash);
> +       spi_message_add_tail(&t[0], &m);
> +
> +       t[1].tx_buf = buf;
> +       spi_message_add_tail(&t[1], &m);
> +
> +       /* Wait until finished previous write command. */
> +       if (wait_till_ready(flash))
> +               return -ETIME;
> +
> +       write_enable(flash);
> +
> +       /* Set up the opcode in the write buffer. */
> +       flash->command[0] = OPCODE_PP;
> +       m25p_addr2cmd(flash, offset, flash->command);
> +
> +       page_offset = offset & (flash->page_size - 1);
> +
> +       /* do all the bytes fit onto one page? */
> +       if (page_offset + count <= flash->page_size) {
> +               t[1].len = count;
> +
> +               spi_sync(flash->spi, &m);
> +
> +               retlen = m.actual_length - m25p_cmdsz(flash);
> +       } else {
> +               u32 i;
> +
> +               /* the size of data remaining on the first page */
> +               page_size = flash->page_size - page_offset;
> +
> +               t[1].len = page_size;
> +               spi_sync(flash->spi, &m);
> +
> +               retlen = m.actual_length - m25p_cmdsz(flash);
> +
> +               /* write everything in flash->page_size chunks */
> +               for (i = page_size; i < count; i += page_size) {
> +                       page_size = count - i;
> +                       if (page_size > flash->page_size)
> +                               page_size = flash->page_size;
> +
> +                       /* write the next page to flash */
> +                       m25p_addr2cmd(flash, offset + i, flash->command);
> +
> +                       t[1].tx_buf = buf + i;
> +                       t[1].len = page_size;
> +
> +                       wait_till_ready(flash);
> +
> +                       write_enable(flash);
> +
> +                       spi_sync(flash->spi, &m);
> +
> +                       retlen += m.actual_length - m25p_cmdsz(flash);
> +
> +               }
> +       }
> +
> +       return retlen;
> +}
> +#ifdef CONFIG_MTD_SST25L
> +ssize_t sst_write(struct cdev *cdev, const void *buf, size_t count, ulong offset, ulong flags)
> +{
> +       struct m25p *flash = cdev->priv;
> +       struct spi_transfer t[2];
> +       struct spi_message m;
> +       size_t actual;
> +       ssize_t retlen;
> +       int cmd_sz, ret;
> +
> +       debug("sst_write %ld bytes at 0x%08lX\n", (unsigned long)count, offset);
> +
> +       retlen = 0;
> +
> +       /* sanity checks */
> +       if (!count)
> +               return 0;
> +
> +       if (offset + count > flash->size)
> +               return -EINVAL;
> +
> +       spi_message_init(&m);
> +       memset(t, 0, (sizeof t));
> +
> +       t[0].tx_buf = flash->command;
> +       t[0].len = m25p_cmdsz(flash);
> +       spi_message_add_tail(&t[0], &m);
> +
> +       t[1].tx_buf = buf;
> +       spi_message_add_tail(&t[1], &m);
> +
> +       /* Wait until finished previous write command. */
> +       ret = wait_till_ready(flash);
> +       if (ret)
> +               goto time_out;
> +
> +       write_enable(flash);
> +
> +       actual = offset % 2;
> +       /* Start write from odd address. */
> +       if (actual) {
> +               flash->command[0] = OPCODE_BP;
> +               m25p_addr2cmd(flash, offset, flash->command);
> +
> +               /* write one byte. */
> +               t[1].len = 1;
> +               spi_sync(flash->spi, &m);
> +               ret = wait_till_ready(flash);
> +               if (ret)
> +                       goto time_out;
> +               retlen += m.actual_length - m25p_cmdsz(flash);
> +       }
> +       offset += actual;
> +
> +       flash->command[0] = OPCODE_AAI_WP;
> +       m25p_addr2cmd(flash, offset, flash->command);
> +
> +       /* Write out most of the data here. */
> +       cmd_sz = m25p_cmdsz(flash);
> +       for (; actual < count - 1; actual += 2) {
> +               t[0].len = cmd_sz;
> +               /* write two bytes. */
> +               t[1].len = 2;
> +               t[1].tx_buf = buf + actual;
> +
> +               spi_sync(flash->spi, &m);
> +               ret = wait_till_ready(flash);
> +               if (ret)
> +                       goto time_out;
> +               retlen += m.actual_length - cmd_sz;
> +               cmd_sz = 1;
> +               offset += 2;
> +       }
> +       write_disable(flash);
> +       ret = wait_till_ready(flash);
> +       if (ret)
> +               goto time_out;
> +
> +       /* Write out trailing byte if it exists. */
> +       if (actual != count) {
> +               write_enable(flash);
> +               flash->command[0] = OPCODE_BP;
> +               m25p_addr2cmd(flash, offset, flash->command);
> +               t[0].len = m25p_cmdsz(flash);
> +               t[1].len = 1;
> +               t[1].tx_buf = buf + actual;
> +
> +               spi_sync(flash->spi, &m);
> +               ret = wait_till_ready(flash);
> +               if (ret)
> +                       goto time_out;
> +               retlen += m.actual_length - m25p_cmdsz(flash);
> +               write_disable(flash);
> +       }
> +
> +time_out:
> +       return retlen;
> +}
> +#endif
> +
> +static void m25p80_info(struct device_d *dev)
> +{
> +       struct m25p             *flash = dev->priv;
> +       struct flash_info       *info = flash->info;
> +
> +       printf("Flash type        : %s\n", flash->name);
> +       printf("Size              : %lldKiB\n", (long long)flash->size / 1024);
> +       printf("Number of sectors : %d\n", info->n_sectors);
> +       printf("Sector size       : %dKiB\n", info->sector_size / 1024);
> +       printf("\n");
> +}
> +
> +
> +/****************************************************************************/
> +
> +/*
> + * SPI device driver setup and teardown
> + */
> +
> +#define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags)     \
> +       ((unsigned long)&(struct flash_info) {                          \
> +               .jedec_id = (_jedec_id),                                \
> +               .ext_id = (_ext_id),                                    \
> +               .sector_size = (_sector_size),                          \
> +               .n_sectors = (_n_sectors),                              \
> +               .page_size = 256,                                       \
> +               .flags = (_flags),                                      \
> +       })
> +
> +#define CAT25_INFO(_sector_size, _n_sectors, _page_size, _addr_width)  \
> +       ((unsigned long)&(struct flash_info) {                          \
> +               .sector_size = (_sector_size),                          \
> +               .n_sectors = (_n_sectors),                              \
> +               .page_size = (_page_size),                              \
> +               .addr_width = (_addr_width),                            \
> +               .flags = M25P_NO_ERASE,                                 \
> +       })
> +
> +/* NOTE: double check command sets and memory organization when you add
> + * more flash chips.  This current list focusses on newer chips, which
> + * have been converging on command sets which including JEDEC ID.
> + */
> +static const struct spi_device_id m25p_ids[] = {
> +       /* Atmel -- some are (confusingly) marketed as "DataFlash" */
> +       { "at25fs010",  INFO(0x1f6601, 0, 32 * 1024,   4, SECT_4K) },
> +       { "at25fs040",  INFO(0x1f6604, 0, 64 * 1024,   8, SECT_4K) },
> +
> +       { "at25df041a", INFO(0x1f4401, 0, 64 * 1024,   8, SECT_4K) },
> +       { "at25df641",  INFO(0x1f4800, 0, 64 * 1024, 128, SECT_4K) },
> +
> +       { "at26f004",   INFO(0x1f0400, 0, 64 * 1024,  8, SECT_4K) },
> +       { "at26df081a", INFO(0x1f4501, 0, 64 * 1024, 16, SECT_4K) },
> +       { "at26df161a", INFO(0x1f4601, 0, 64 * 1024, 32, SECT_4K) },
> +       { "at26df321",  INFO(0x1f4700, 0, 64 * 1024, 64, SECT_4K) },
> +
> +       /* EON -- en25xxx */
> +       { "en25f32", INFO(0x1c3116, 0, 64 * 1024,  64, SECT_4K) },
> +       { "en25p32", INFO(0x1c2016, 0, 64 * 1024,  64, 0) },
> +       { "en25p64", INFO(0x1c2017, 0, 64 * 1024, 128, 0) },
> +
> +       /* Intel/Numonyx -- xxxs33b */
> +       { "160s33b",  INFO(0x898911, 0, 64 * 1024,  32, 0) },
> +       { "320s33b",  INFO(0x898912, 0, 64 * 1024,  64, 0) },
> +       { "640s33b",  INFO(0x898913, 0, 64 * 1024, 128, 0) },
> +
> +       /* Macronix */
> +       { "mx25l4005a",  INFO(0xc22013, 0, 64 * 1024,   8, SECT_4K) },
> +       { "mx25l8005",   INFO(0xc22014, 0, 64 * 1024,  16, 0) },
> +       { "mx25l3205d",  INFO(0xc22016, 0, 64 * 1024,  64, 0) },
> +       { "mx25l6405d",  INFO(0xc22017, 0, 64 * 1024, 128, 0) },
> +       { "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, 0) },
> +       { "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) },
> +       { "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, 0) },
> +       { "mx25l25655e", INFO(0xc22619, 0, 64 * 1024, 512, 0) },
> +
> +       /* Spansion -- single (large) sector size only, at least
> +        * for the chips listed here (without boot sectors).
> +        */
> +       { "s25sl004a",  INFO(0x010212,      0,  64 * 1024,   8, 0) },
> +       { "s25sl008a",  INFO(0x010213,      0,  64 * 1024,  16, 0) },
> +       { "s25sl016a",  INFO(0x010214,      0,  64 * 1024,  32, 0) },
> +       { "s25sl032a",  INFO(0x010215,      0,  64 * 1024,  64, 0) },
> +       { "s25sl032p",  INFO(0x010215, 0x4d00,  64 * 1024,  64, SECT_4K) },
> +       { "s25sl064a",  INFO(0x010216,      0,  64 * 1024, 128, 0) },
> +       { "s25sl12800", INFO(0x012018, 0x0300, 256 * 1024,  64, 0) },
> +       { "s25sl12801", INFO(0x012018, 0x0301,  64 * 1024, 256, 0) },
> +       { "s25fl129p0", INFO(0x012018, 0x4d00, 256 * 1024,  64, 0) },
> +       { "s25fl129p1", INFO(0x012018, 0x4d01,  64 * 1024, 256, 0) },
> +       { "s25fl016k",  INFO(0xef4015,      0,  64 * 1024,  32, SECT_4K) },
> +       { "s25fl064k",  INFO(0xef4017,      0,  64 * 1024, 128, SECT_4K) },
> +
> +       /* SST -- large erase sizes are "overlays", "sectors" are 4K */
> +       { "sst25vf040b", INFO(0xbf258d, 0, 64 * 1024,  8, SECT_4K) },
> +       { "sst25vf080b", INFO(0xbf258e, 0, 64 * 1024, 16, SECT_4K) },
> +       { "sst25vf016b", INFO(0xbf2541, 0, 64 * 1024, 32, SECT_4K) },
> +       { "sst25vf032b", INFO(0xbf254a, 0, 64 * 1024, 64, SECT_4K) },
> +       { "sst25wf512",  INFO(0xbf2501, 0, 64 * 1024,  1, SECT_4K) },
> +       { "sst25wf010",  INFO(0xbf2502, 0, 64 * 1024,  2, SECT_4K) },
> +       { "sst25wf020",  INFO(0xbf2503, 0, 64 * 1024,  4, SECT_4K) },
> +       { "sst25wf040",  INFO(0xbf2504, 0, 64 * 1024,  8, SECT_4K) },
> +
> +       /* ST Microelectronics -- newer production may have feature updates */
> +       { "m25p05",  INFO(0x202010,  0,  32 * 1024,   2, 0) },
> +       { "m25p10",  INFO(0x202011,  0,  32 * 1024,   4, 0) },
> +       { "m25p20",  INFO(0x202012,  0,  64 * 1024,   4, 0) },
> +       { "m25p40",  INFO(0x202013,  0,  64 * 1024,   8, 0) },
> +       { "m25p80",  INFO(0x202014,  0,  64 * 1024,  16, 0) },
> +       { "m25p16",  INFO(0x202015,  0,  64 * 1024,  32, 0) },
> +       { "m25p32",  INFO(0x202016,  0,  64 * 1024,  64, 0) },
> +       { "m25p64",  INFO(0x202017,  0,  64 * 1024, 128, 0) },
> +       { "m25p128", INFO(0x202018,  0, 256 * 1024,  64, 0) },
> +
> +       { "m25p05-nonjedec",  INFO(0, 0,  32 * 1024,   2, 0) },
> +       { "m25p10-nonjedec",  INFO(0, 0,  32 * 1024,   4, 0) },
> +       { "m25p20-nonjedec",  INFO(0, 0,  64 * 1024,   4, 0) },
> +       { "m25p40-nonjedec",  INFO(0, 0,  64 * 1024,   8, 0) },
> +       { "m25p80-nonjedec",  INFO(0, 0,  64 * 1024,  16, 0) },
> +       { "m25p16-nonjedec",  INFO(0, 0,  64 * 1024,  32, 0) },
> +       { "m25p32-nonjedec",  INFO(0, 0,  64 * 1024,  64, 0) },
> +       { "m25p64-nonjedec",  INFO(0, 0,  64 * 1024, 128, 0) },
> +       { "m25p128-nonjedec", INFO(0, 0, 256 * 1024,  64, 0) },
> +
> +       { "m45pe10", INFO(0x204011,  0, 64 * 1024,    2, 0) },
> +       { "m45pe80", INFO(0x204014,  0, 64 * 1024,   16, 0) },
> +       { "m45pe16", INFO(0x204015,  0, 64 * 1024,   32, 0) },
> +
> +       { "m25pe80", INFO(0x208014,  0, 64 * 1024, 16,       0) },
> +       { "m25pe16", INFO(0x208015,  0, 64 * 1024, 32, SECT_4K) },
> +
> +       { "m25px64", INFO(0x207117,  0, 64 * 1024, 128, 0) },
> +
> +       /* Winbond -- w25x "blocks" are 64K, "sectors" are 4KiB */
> +       { "w25x10", INFO(0xef3011, 0, 64 * 1024,  2,  SECT_4K) },
> +       { "w25x20", INFO(0xef3012, 0, 64 * 1024,  4,  SECT_4K) },
> +       { "w25x40", INFO(0xef3013, 0, 64 * 1024,  8,  SECT_4K) },
> +       { "w25x80", INFO(0xef3014, 0, 64 * 1024,  16, SECT_4K) },
> +       { "w25x16", INFO(0xef3015, 0, 64 * 1024,  32, SECT_4K) },
> +       { "w25x32", INFO(0xef3016, 0, 64 * 1024,  64, SECT_4K) },
> +       { "w25q32", INFO(0xef4016, 0, 64 * 1024,  64, SECT_4K) },
> +       { "w25x64", INFO(0xef3017, 0, 64 * 1024, 128, SECT_4K) },
> +       { "w25q64", INFO(0xef4017, 0, 64 * 1024, 128, SECT_4K) },
> +
> +       /* Catalyst / On Semiconductor -- non-JEDEC */
> +       { "cat25c11", CAT25_INFO(  16, 8, 16, 1) },
> +       { "cat25c03", CAT25_INFO(  32, 8, 16, 2) },
> +       { "cat25c09", CAT25_INFO( 128, 8, 32, 2) },
> +       { "cat25c17", CAT25_INFO( 256, 8, 32, 2) },
> +       { "cat25128", CAT25_INFO(2048, 8, 64, 2) },
> +       { },
> +};
> +
> +static const struct spi_device_id *jedec_probe(struct spi_device *spi)
> +{
> +       int                     tmp;
> +       u8                      code = OPCODE_RDID;
> +       u8                      id[5];
> +       u32                     jedec;
> +       u16                     ext_jedec;
> +       struct flash_info       *info;
> +
> +       /* JEDEC also defines an optional "extended device information"
> +        * string for after vendor-specific data, after the three bytes
> +        * we use here.  Supporting some chips might require using it.
> +        */
> +       spi_write_then_read(spi, &code, 1, id, 5);
> +
> +       jedec = id[0];
> +       jedec = jedec << 8;
> +       jedec |= id[1];
> +       jedec = jedec << 8;
> +       jedec |= id[2];
> +
> +       ext_jedec = id[3] << 8 | id[4];
> +
> +       for (tmp = 0; tmp < ARRAY_SIZE(m25p_ids) - 1; tmp++) {
> +               info = (void *)m25p_ids[tmp].driver_data;
> +               if (info->jedec_id == jedec) {
> +                       if (info->ext_id != 0 && info->ext_id != ext_jedec)
> +                               continue;
> +                       return &m25p_ids[tmp];
> +               }
> +       }
> +       debug("unrecognized JEDEC id %06x\n", jedec);
> +
> +       return NULL;
> +}
> +
> +
> +static struct file_operations m25p80_ops = {
> +       .read   = m25p80_read,
> +       .write  = m25p80_write,
> +       .erase  = m25p80_erase,
> +       .lseek  = dev_lseek_default,
> +};
> +
> +/*
> + * board specific setup should have ensured the SPI clock used here
> + * matches what the READ command supports, at least until this driver
> + * understands FAST_READ (for clocks over 25 MHz).
> + */
> +static int m25p_probe(struct device_d *dev)
> +{
> +       struct spi_device *spi = (struct spi_device *)dev->type_data;
> +       const struct spi_device_id      *id = NULL;
> +       struct flash_info               *info = NULL;
> +       struct flash_platform_data      *data;
> +       struct m25p                     *flash;
> +       unsigned                        i;
> +       unsigned                        do_jdec_probe = 1;
> +
> +       /* Platform data helps sort out which chip type we have, as
> +        * well as how this board partitions it.  If we don't have
> +        * a chip ID, try the JEDEC id commands; they'll work for most
> +        * newer chips, even if we don't recognize the particular chip.
> +        */
> +       data = dev->platform_data;
> +
> +       if (data && data->type) {
> +               const struct spi_device_id *plat_id;
> +
> +               for (i = 0; i < ARRAY_SIZE(m25p_ids) - 1; i++) {
> +                       plat_id = &m25p_ids[i];
> +                       if (strcmp(data->type, plat_id->name))
> +                               continue;
> +                       break;
> +               }
> +
> +               if (i < ARRAY_SIZE(m25p_ids) - 1) {
> +                       id = plat_id;
> +                       info = (void *)id->driver_data;
> +                       /* If flash type is provided but the memory is not
> +                        * JEDEC compliant, don't try to probe the JEDEC id */
> +                       if (!info->jedec_id)
> +                               do_jdec_probe = 0;
> +               } else
> +                       dev_warn(&spi->dev, "unrecognized id %s\n", data->type);
> +       }
> +
> +       if (do_jdec_probe) {
> +               const struct spi_device_id *jid;
> +
> +               jid = jedec_probe(spi);
> +               if (!jid) {
> +                       return -ENODEV;
> +               } else if (jid != id) {
> +
> +                       /*
> +                        * JEDEC knows better, so overwrite platform ID. We
> +                        * can't trust partitions any longer, but we'll let
> +                        * mtd apply them anyway, since some partitions may be
> +                        * marked read-only, and we don't want to lose that
> +                        * information, even if it's not 100% accurate.
> +                        */
> +                       if (id)
> +                               printf("%s: found %s, expected %s\n", dev->name,
> +                                        jid->name, id->name);
> +
> +                       id = jid;
> +                       info = (void *)jid->driver_data;
> +               }
> +       }
> +
> +       flash = xzalloc(sizeof *flash);
> +       if (!flash)
> +               return -ENOMEM;
> +
> +       flash->command = xmalloc(MAX_CMD_SIZE + FAST_READ_DUMMY_BYTE);
> +       if (!flash->command) {
> +               free(flash);
> +               return -ENOMEM;
> +       }
> +
> +       flash->spi = spi;
> +       dev->priv = (void *)flash;
> +       /*
> +        * Atmel, SST and Intel/Numonyx serial flash tend to power
> +        * up with the software protection bits set
> +        */
> +
> +       if (info->jedec_id >> 16 == 0x1f ||
> +           info->jedec_id >> 16 == 0x89 ||
> +           info->jedec_id >> 16 == 0xbf) {
> +               write_enable(flash);
> +               write_sr(flash, 0);
> +       }
> +
> +       flash->name = (char *)id->name;
> +       flash->info = info;
> +       flash->size = info->sector_size * info->n_sectors;
> +       flash->erasesize = info->sector_size;
> +       flash->cdev.size = info->sector_size * info->n_sectors;
> +       flash->cdev.dev = dev;
> +       flash->cdev.ops = &m25p80_ops;
> +       flash->cdev.priv = flash;
> +
> +       if (data && data->name)
> +               flash->cdev.name = asprintf("%s%d", data->name, dev->id);
> +       else
> +               flash->cdev.name = asprintf("%s", (char *)dev_name(&spi->dev));
> +
> +#ifdef CONFIG_MTD_SST25L
> +       /* sst flash chips use AAI word program */
> +       if (info->jedec_id >> 16 == 0xbf)
> +               m25p80_ops.write = sst_write;
> +       else
> +#endif
> +               m25p80_ops.write = m25p80_write;
> +
> +       /* prefer "small sector" erase if possible */
> +       if (info->flags & SECT_4K)
> +               flash->erase_opcode = OPCODE_BE_4K;
> +       else
> +               flash->erase_opcode = OPCODE_SE;
> +
> +       flash->page_size = info->page_size;
> +
> +       if (info->addr_width)
> +               flash->addr_width = info->addr_width;
> +       else {
> +               /* enable 4-byte addressing if the device exceeds 16MiB */
> +               if (flash->size > 0x1000000) {
> +                       flash->addr_width = 4;
> +                       set_4byte(flash, 1);
> +               } else
> +                       flash->addr_width = 3;
> +       }
> +
> +       printf("%s: %s (%lld Kbytes)\n", flash->cdev.name, id->name,
> +                       (long long)flash->size >> 10);
> +
> +       devfs_create(&flash->cdev);
> +
> +       return 0;
> +}
> +
> +static struct driver_d epcs_flash_driver = {
> +       .name  = "m25p",
> +       .probe = m25p_probe,
> +       .info = m25p80_info,
> +};
> +
> +static int epcs_init(void)
> +{
> +       register_driver(&epcs_flash_driver);
> +       return 0;
> +}
> +
> +device_initcall(epcs_init);
> +
> diff --git a/drivers/nor/m25p80.h b/drivers/nor/m25p80.h
> new file mode 100644
> index 0000000..3f9dd9c
> --- /dev/null
> +++ b/drivers/nor/m25p80.h
> @@ -0,0 +1,90 @@
> +#ifndef _M25P80_H_
> +#define _M25P80_H_
> +
> +/* Flash opcodes. */
> +#define        OPCODE_WREN             0x06    /* Write enable */
> +#define        OPCODE_RDSR             0x05    /* Read status register */
> +#define        OPCODE_WRSR             0x01    /* Write status register 1 byte */
> +#define        OPCODE_NORM_READ        0x03    /* Read data bytes (low frequency) */
> +#define        OPCODE_FAST_READ        0x0b    /* Read data bytes (high frequency) */
> +#define        OPCODE_PP               0x02    /* Page program (up to 256 bytes) */
> +#define        OPCODE_BE_4K            0x20    /* Erase 4KiB block */
> +#define        OPCODE_BE_32K           0x52    /* Erase 32KiB block */
> +#define        OPCODE_CHIP_ERASE       0xc7    /* Erase whole flash chip */
> +#define        OPCODE_SE               0xd8    /* Sector erase (usually 64KiB) */
> +#define        OPCODE_RDID             0x9f    /* Read JEDEC ID */
> +
> +/* Used for SST flashes only. */
> +#define        OPCODE_BP               0x02    /* Byte program */
> +#define        OPCODE_WRDI             0x04    /* Write disable */
> +#define        OPCODE_AAI_WP           0xad    /* Auto address increment word program */
> +
> +/* Used for Macronix flashes only. */
> +#define        OPCODE_EN4B             0xb7    /* Enter 4-byte mode */
> +#define        OPCODE_EX4B             0xe9    /* Exit 4-byte mode */
> +
> +/* Status Register bits. */
> +#define        SR_WIP                  1       /* Write in progress */
> +#define        SR_WEL                  2       /* Write enable latch */
> +/* meaning of other SR_* bits may differ between vendors */
> +#define        SR_BP0                  4       /* Block protect 0 */
> +#define        SR_BP1                  8       /* Block protect 1 */
> +#define        SR_BP2                  0x10    /* Block protect 2 */
> +#define        SR_SRWD                 0x80    /* SR write protect */
> +
> +/* Define max times to check status register before we give up. */
> +#define        MAX_READY_WAIT          40      /* M25P16 specs 40s max chip erase */
> +#define MAX_CMD_SIZE           5
> +
> +#ifdef CONFIG_M25PXX_USE_FAST_READ
> +#define OPCODE_READ            OPCODE_FAST_READ
> +#define FAST_READ_DUMMY_BYTE   1
> +#else
> +#define OPCODE_READ            OPCODE_NORM_READ
> +#define FAST_READ_DUMMY_BYTE   0
> +#endif
> +
> +#define SPI_NAME_SIZE   32
> +
> +struct spi_device_id {
> +       char name[SPI_NAME_SIZE];
> +       unsigned long driver_data;
> +};
> +
> +struct m25p {
> +       struct spi_device       *spi;
> +       struct flash_info       *info;
> +       struct mtd_info mtd;
> +       struct cdev             cdev;
> +       char                    *name;
> +       u32                     erasesize;
> +       u16                     page_size;
> +       u16                     addr_width;
> +       u8                      erase_opcode;
> +       u8                      *command;
> +       u32                     size;
> +};
> +
> +struct flash_info {
> +       /* JEDEC id zero means "no ID" (most older chips); otherwise it has
> +        * a high byte of zero plus three data bytes: the manufacturer id,
> +        * then a two byte device id.
> +        */
> +       u32             jedec_id;
> +       u16             ext_id;
> +
> +       /* The size listed here is what works with OPCODE_SE, which isn't
> +        * necessarily called a "sector" by the vendor.
> +        */
> +       unsigned        sector_size;
> +       u16             n_sectors;
> +
> +       u16             page_size;
> +       u16             addr_width;
> +
> +       u16             flags;
> +#define        SECT_4K         0x01            /* OPCODE_BE_4K works uniformly */
> +#define        M25P_NO_ERASE   0x02            /* No erase command needed */
> +};
> +
> +#endif
> diff --git a/include/spi/flash.h b/include/spi/flash.h
> new file mode 100644
> index 0000000..cbd0203
> --- /dev/null
> +++ b/include/spi/flash.h
> @@ -0,0 +1,30 @@
> +#ifndef LINUX_SPI_FLASH_H
> +#define LINUX_SPI_FLASH_H
> +
> +struct mtd_partition;
> +
> +/**
> + * struct flash_platform_data: board-specific flash data
> + * @name: optional flash device name (eg, as used with mtdparts=)
> + * @parts: optional array of mtd_partitions for static partitioning
> + * @nr_parts: number of mtd_partitions for static partitoning
> + * @type: optional flash device type (e.g. m25p80 vs m25p64), for use
> + *     with chips that can't be queried for JEDEC or other IDs
> + *
> + * Board init code (in arch/.../mach-xxx/board-yyy.c files) can
> + * provide information about SPI flash parts (such as DataFlash) to
> + * help set up the device and its appropriate default partitioning.
> + *
> + * Note that for DataFlash, sizes for pages, blocks, and sectors are
> + * rarely powers of two; and partitions should be sector-aligned.
> + */
> +struct flash_platform_data {
> +       char                    *name;
> +       struct mtd_partition    *parts;
> +       unsigned int            nr_parts;
> +       char                    *type;
> +
> +       /* we'll likely add more ... use JEDEC IDs, etc */
> +};
> +
> +#endif
> --
> 1.7.6
>
>
> _______________________________________________
> barebox mailing list
> barebox@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
>

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

  reply	other threads:[~2011-07-31 15:46 UTC|newest]

Thread overview: 4+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2011-07-30 20:24 franck.jullien
2011-07-31 15:46 ` Hubert Feurstein [this message]
2011-07-31 17:06   ` Franck JULLIEN
2011-08-01  8:52 ` Sascha Hauer

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to='CAFfN3gUyF-ptBO7y4P2pufYoVrF=eArZaQT5JFEgC3S3Otjw=Q@mail.gmail.com' \
    --to=h.feurstein@gmail.com \
    --cc=barebox@lists.infradead.org \
    --cc=franck.jullien@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox