From: Sascha Hauer <s.hauer@pengutronix.de>
To: David Picard <david.picard@clermont.in2p3.fr>
Cc: BAREBOX <barebox@lists.infradead.org>, Ahmad Fatoum <ahmad@a3f.at>
Subject: Re: [PATCH v2 00/10] ARM: boards: add support for Enclustra Mercury SA2
Date: Fri, 26 Sep 2025 14:47:05 +0200 [thread overview]
Message-ID: <aNaLSRX9xUz6GEEK@pengutronix.de> (raw)
In-Reply-To: <20250925-boards-enclustra-sa2-add-support-v2-0-6820ad6c6256@clermont.in2p3.fr>
Hi David,
Please squash patches 2, 3, 4, 5, 6, 7 and 10 into one patch.
It's easier to review the end result rather than development steps.
The handoff files should stay a separate commit though because they are
quite big and only contain autogenerated stuff.
Sascha
On Thu, Sep 25, 2025 at 01:59:07PM +0200, David Picard wrote:
> Add support for the Enclustra Mercury+ SA2, a Cyclone V based
> SoC FPGA.
> https://www.enclustra.com/en/products/system-on-chip-modules/mercury-sa2/
>
> The SoM provides a 64MiB NOR QSPI flash, DDR3, Ethernet PHY, RTC.
>
> The Cyclone V features a hardware ARM core (aka HPS) that can boot
> from SD card (MMC), QSPI flash. This patch series focusses on MMC.
>
> Signed-off-by: David Picard <david.picard@clermont.in2p3.fr>
> ---
> Changes in v2:
> - EDITME: describe what is new in this series revision.
> - EDITME: use bulletpoints and terse descriptions.
> - Link to v1: https://lore.kernel.org/r/20250917-boards-enclustra-sa2-add-support-v1-0-2de8f69107a1@clermont.in2p3.fr
>
> ---
> David Picard (8):
> Add handoff files
> Add Enclustra Mercury+ SA2 module
> ARM: dts: socfpga: use upstream SA2 device tree
> ARM: dts: socfpga: adapt upstream SA2 device tree
> boards: enclustra-sa2: read MAC address from EEPROM
> boards: enclustra-sa2: configure SI5338
> boards: enclustra-sa2: enable SI5338
> boards: enclustra-sa2: read S/N from EEPROM
>
> Sascha Hauer (2):
> lib: add crc16 support
> nvmem: add support for Atmel sha204(a)
>
> arch/arm/boards/Makefile | 1 +
> arch/arm/boards/enclustra-sa2/Makefile | 2 +
> .../boards/enclustra-sa2/Si5338-RevB-Registers.h | 433 +++++++++++++
> arch/arm/boards/enclustra-sa2/board.c | 148 +++++
> .../boards/enclustra-sa2/iocsr_config_cyclone5.c | 678 +++++++++++++++++++++
> arch/arm/boards/enclustra-sa2/lowlevel.c | 15 +
> arch/arm/boards/enclustra-sa2/pinmux_config.c | 241 ++++++++
> arch/arm/boards/enclustra-sa2/pll_config.h | 107 ++++
> arch/arm/boards/enclustra-sa2/sdram_config.h | 112 ++++
> arch/arm/boards/enclustra-sa2/sequencer_auto.h | 225 +++++++
> .../boards/enclustra-sa2/sequencer_auto_ac_init.c | 67 ++
> .../enclustra-sa2/sequencer_auto_inst_init.c | 158 +++++
> arch/arm/boards/enclustra-sa2/sequencer_defines.h | 165 +++++
> arch/arm/boards/enclustra-sa2/si5338_config.c | 252 ++++++++
> arch/arm/boards/enclustra-sa2/si5338_config.h | 22 +
> arch/arm/configs/socfpga-xload_defconfig | 1 +
> arch/arm/configs/socfpga_defconfig | 3 +-
> arch/arm/dts/Makefile | 1 +
> arch/arm/dts/socfpga_cyclone5_mercury_sa2.dts | 17 +
> arch/arm/dts/socfpga_cyclone5_mercury_sa2.dtsi | 213 +++++++
> arch/arm/mach-socfpga/Kconfig | 8 +
> drivers/nvmem/Kconfig | 15 +
> drivers/nvmem/Makefile | 2 +
> drivers/nvmem/atmel-i2c.c | 302 +++++++++
> drivers/nvmem/atmel-i2c.h | 180 ++++++
> drivers/nvmem/atmel-sha204a.c | 114 ++++
> images/Makefile.socfpga | 8 +
> include/linux/crc16.h | 21 +
> lib/Kconfig | 3 +
> lib/Makefile | 1 +
> lib/crc16.c | 69 +++
> 31 files changed, 3582 insertions(+), 2 deletions(-)
> ---
> base-commit: 85c11b44889eb73921b2095f2c42492ac3d686a0
> change-id: 20250916-boards-enclustra-sa2-add-support-4704233a6861
>
> Best regards,
> --
> David Picard <david.picard@clermont.in2p3.fr>
>
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
next prev parent reply other threads:[~2025-09-26 12:47 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-09-25 11:59 David Picard
2025-09-25 11:59 ` [PATCH v2 01/10] Add handoff files David Picard
2025-09-25 11:59 ` [PATCH v2 02/10] Add Enclustra Mercury+ SA2 module David Picard
2025-09-25 11:59 ` [PATCH v2 03/10] ARM: dts: socfpga: use upstream SA2 device tree David Picard
2025-09-25 11:59 ` [PATCH v2 04/10] ARM: dts: socfpga: adapt " David Picard
2025-09-25 11:59 ` [PATCH v2 05/10] boards: enclustra-sa2: read MAC address from EEPROM David Picard
2025-09-26 12:40 ` Sascha Hauer
2025-09-26 12:57 ` David Picard
2025-09-29 8:04 ` David Picard
2025-09-25 11:59 ` [PATCH v2 06/10] boards: enclustra-sa2: configure SI5338 David Picard
2025-09-25 11:59 ` [PATCH v2 07/10] boards: enclustra-sa2: enable SI5338 David Picard
2025-09-25 11:59 ` [PATCH v2 08/10] lib: add crc16 support David Picard
2025-09-26 12:43 ` Sascha Hauer
2025-09-25 11:59 ` [PATCH v2 09/10] nvmem: add support for Atmel sha204(a) David Picard
2025-09-25 11:59 ` [PATCH v2 10/10] boards: enclustra-sa2: read S/N from EEPROM David Picard
2025-09-26 12:47 ` Sascha Hauer [this message]
2025-09-30 10:40 ` [PATCH v2 00/10] ARM: boards: add support for Enclustra Mercury SA2 Sascha Hauer
2025-09-30 11:47 ` David Picard
2025-09-30 11:49 ` David Picard
[not found] ` <aade6cdb-3244-4468-8bab-215a54fdef15@clermont.in2p3.fr>
2025-10-01 8:29 ` Sascha Hauer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=aNaLSRX9xUz6GEEK@pengutronix.de \
--to=s.hauer@pengutronix.de \
--cc=ahmad@a3f.at \
--cc=barebox@lists.infradead.org \
--cc=david.picard@clermont.in2p3.fr \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox