* Re: Problems with pyhBoard-Wega-AM335x
@ 2014-07-04 13:26 Rolf Evers-Fischer
[not found] ` <53BA5442.6020708@ma-info.de>
0 siblings, 1 reply; 15+ messages in thread
From: Rolf Evers-Fischer @ 2014-07-04 13:26 UTC (permalink / raw)
To: florian.frede; +Cc: barebox
Hi Florian,
On Fri, Jul 04, 2014 at 12:12, Florian Wrede wrote:
> I like to update from barebox 2013.11 to barebox 2014.06.0 with the
> phyBoard-Wega-AM335x. After reconfigure the barebox I get the error:
>
> LD images/start_am33xx_phytec_phycore_sram.pbl
> arch/arm/boards/built-in-pbl.o: In function `pcm051_board_init':
> :(.text.pcm051_board_init+0x94): undefined reference to
> `__dtb_am335x_phytec_phycore_start'
> make[2]: *** [images/start_am33xx_phytec_phycore_sram.pbl] Error 1
> make[1]: *** [images] Error 2
I've had the same problem after updating my beaglebone project to a newer
barebox version.
Could you please check your barebox configuration?
The new config item "Allow multiple boards to be selected" in "System
Type"->"OMAP Features" needs to be selected. After that you should be able to select the "Phytec
phyCORE pcm051" board.
A rebuild will create a file called "am335x-phytec-phycore-dtb.S" in the
folder arch/arm/dts. This file contains the missing symbols.
Best regards,
Rolf
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Problems with pyhBoard-Wega-AM335x
[not found] ` <53BA5442.6020708@ma-info.de>
@ 2014-07-07 8:04 ` Frede Florian
2014-07-07 10:05 ` Rolf Evers-Fischer
1 sibling, 0 replies; 15+ messages in thread
From: Frede Florian @ 2014-07-07 8:04 UTC (permalink / raw)
To: barebox
[-- Attachment #1: Type: text/plain, Size: 1513 bytes --]
Hello Rolf,
I used this Option already, but to be sure that there is no mistake I
reconfigured the Barebox and Barebox_MLO again and use the new Version
2014.07.0. The result is the same.
LD images/start_am33xx_phytec_phycore_sram.pbl
arch/arm/boards/built-in-pbl.o: In function `pcm051_board_init':
:(.text.pcm051_board_init+0x94): undefined reference to
`__dtb_am335x_phytec_phycore_start'
make[2]: *** [images/start_am33xx_phytec_phycore_sram.pbl] Error 1
make[2]: *** Waiting for unfinished jobs....
make[1]: Leaving directory
`/phytec/phyBOARD-WEGA-AM335x-PD13.0.0/platform-phyBOARD-WEGA-AM335x/build-target/barebox_mlo-2014.07.0'
make[1]: *** [images] Error 2
make: ***
[/phytec/phyBOARD-WEGA-AM335x-PD13.0.0/platform-phyBOARD-WEGA-AM335x/state/barebox_mlo.compile]
Error 2
I also attached the config files may be there is an other error?
Regards
Florian
Am 04.07.2014 15:26, schrieb Rolf Evers-Fischer:
> Hi Florian,
>
> [...]
>
> I've had the same problem after updating my beaglebone project to a newer
> barebox version.
>
> Could you please check your barebox configuration?
> The new config item "Allow multiple boards to be selected" in "System
> Type"->"OMAP Features" needs to be selected. After that you should be able to select the "Phytec
> phyCORE pcm051" board.
>
> A rebuild will create a file called "am335x-phytec-phycore-dtb.S" in the
> folder arch/arm/dts. This file contains the missing symbols.
>
> Best regards,
> Rolf
>
[-- Attachment #2: barebox.config --]
[-- Type: text/plain, Size: 11645 bytes --]
#
# Automatically generated file; DO NOT EDIT.
# Barebox/arm 2014.07.0 Configuration
#
CONFIG_ARM=y
CONFIG_ARM_LINUX=y
#
# System Type
#
# CONFIG_ARCH_AT91 is not set
# CONFIG_ARCH_BCM2835 is not set
# CONFIG_ARCH_CLPS711X is not set
# CONFIG_ARCH_DAVINCI is not set
# CONFIG_ARCH_EP93XX is not set
# CONFIG_ARCH_HIGHBANK is not set
# CONFIG_ARCH_IMX is not set
# CONFIG_ARCH_MVEBU is not set
# CONFIG_ARCH_MXS is not set
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_NOMADIK is not set
CONFIG_ARCH_OMAP=y
# CONFIG_ARCH_PXA is not set
# CONFIG_ARCH_ROCKCHIP is not set
# CONFIG_ARCH_SOCFPGA is not set
# CONFIG_ARCH_S3C24xx is not set
# CONFIG_ARCH_S5PCxx is not set
# CONFIG_ARCH_S3C64xx is not set
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_VEXPRESS is not set
# CONFIG_ARCH_TEGRA is not set
# CONFIG_ARCH_UEMD is not set
# CONFIG_ARCH_ZYNQ is not set
#
# Processor Type
#
CONFIG_CPU_32=y
CONFIG_CPU_V7=y
CONFIG_CPU_32v7=y
#
# processor features
#
# CONFIG_BOOT_ENDIANNESS_SWITCH is not set
CONFIG_BAREBOX_MAX_IMAGE_SIZE=0xffffffff
#
# OMAP Features
#
CONFIG_ARCH_AM33XX=y
CONFIG_OMAP_CLOCK_SOURCE_DMTIMER0=y
CONFIG_OMAP_GPMC=y
# CONFIG_OMAP_BUILD_IFT is not set
# CONFIG_OMAP_BUILD_SPI is not set
# CONFIG_BAREBOX_UPDATE_AM33XX_SPI_NOR_MLO is not set
# CONFIG_BAREBOX_UPDATE_AM33XX_NAND_XLOADSLOTS is not set
CONFIG_OMAP_MULTI_BOARDS=y
# CONFIG_MACH_BEAGLEBONE is not set
CONFIG_MACH_PCM051=y
CONFIG_AEABI=y
# CONFIG_THUMB2_BAREBOX is not set
CONFIG_ARM_BOARD_APPEND_ATAG=y
#
# ARM specific settings
#
# CONFIG_CPU_V7_DCACHE_SKIP is not set
CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y
CONFIG_ARM_EXCEPTIONS=y
CONFIG_ARM_UNWIND=y
CONFIG_DEFCONFIG_LIST="$ARCH_DEFCONFIG"
CONFIG_HAS_KALLSYMS=y
CONFIG_HAS_MODULES=y
CONFIG_ENV_HANDLING=y
CONFIG_GENERIC_GPIO=y
CONFIG_BOOTM=y
CONFIG_BLOCK=y
CONFIG_BLOCK_WRITE=y
CONFIG_FILETYPE=y
CONFIG_BINFMT=y
CONFIG_UIMAGE=y
CONFIG_GLOBALVAR=y
CONFIG_STDDEV=y
CONFIG_BAREBOX_UPDATE=y
#
# General Settings
#
CONFIG_LOCALVERSION="LC"
CONFIG_LOCALVERSION_AUTO=y
CONFIG_BANNER=y
CONFIG_MEMINFO=y
CONFIG_ENVIRONMENT_VARIABLES=y
#
# memory layout
#
CONFIG_HAVE_PBL_IMAGE=y
CONFIG_HAVE_PBL_MULTI_IMAGES=y
CONFIG_HAVE_IMAGE_COMPRESSION=y
CONFIG_PBL_IMAGE=y
CONFIG_PBL_MULTI_IMAGES=y
CONFIG_PBL_RELOCATABLE=y
CONFIG_IMAGE_COMPRESSION=y
# CONFIG_IMAGE_COMPRESSION_LZ4 is not set
CONFIG_IMAGE_COMPRESSION_LZO=y
# CONFIG_IMAGE_COMPRESSION_GZIP is not set
# CONFIG_IMAGE_COMPRESSION_NONE is not set
CONFIG_MMU=y
CONFIG_MMU_EARLY=y
CONFIG_HAVE_CONFIGURABLE_TEXT_BASE=y
CONFIG_TEXT_BASE=0x8f000000
CONFIG_BAREBOX_MAX_PBL_SIZE=0xffffffff
CONFIG_BAREBOX_MAX_BARE_INIT_SIZE=0xffffffff
CONFIG_STACK_SIZE=0x8000
CONFIG_MALLOC_SIZE=0x4000000
# CONFIG_BROKEN is not set
# CONFIG_EXPERIMENTAL is not set
CONFIG_MALLOC_DLMALLOC=y
# CONFIG_MALLOC_TLSF is not set
# CONFIG_KALLSYMS is not set
# CONFIG_RELOCATABLE is not set
# CONFIG_PANIC_HANG is not set
CONFIG_PROMPT="barebox@pcm051>"
CONFIG_BAUDRATE=115200
CONFIG_CBSIZE=1024
CONFIG_SHELL_HUSH=y
# CONFIG_SHELL_SIMPLE is not set
# CONFIG_SHELL_NONE is not set
CONFIG_GLOB=y
CONFIG_GLOB_SORT=y
CONFIG_PROMPT_HUSH_PS2="> "
CONFIG_HUSH_FANCY_PROMPT=y
CONFIG_CMDLINE_EDITING=y
CONFIG_AUTO_COMPLETE=y
CONFIG_MENU=y
# CONFIG_PASSWORD is not set
CONFIG_DYNAMIC_CRC_TABLE=y
CONFIG_ERRNO_MESSAGES=y
# CONFIG_TIMESTAMP is not set
# CONFIG_BLSPEC is not set
# CONFIG_KERNEL_INSTALL_TARGET is not set
CONFIG_CONSOLE_FULL=y
# CONFIG_CONSOLE_SIMPLE is not set
# CONFIG_CONSOLE_NONE is not set
CONFIG_CONSOLE_ACTIVATE_FIRST=y
# CONFIG_CONSOLE_ACTIVATE_ALL is not set
# CONFIG_CONSOLE_ACTIVATE_NONE is not set
CONFIG_PARTITION=y
CONFIG_PARTITION_DISK=y
CONFIG_PARTITION_DISK_DOS=y
# CONFIG_PARTITION_DISK_EFI is not set
CONFIG_DEFAULT_ENVIRONMENT=y
# CONFIG_DEFAULT_COMPRESSION_GZIP is not set
# CONFIG_DEFAULT_COMPRESSION_LZO is not set
CONFIG_DEFAULT_COMPRESSION_NONE=y
CONFIG_HAVE_DEFAULT_ENVIRONMENT_NEW=y
CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW=y
CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/pcm051/env"
# CONFIG_BAREBOXENV_TARGET is not set
# CONFIG_BAREBOXCRC32_TARGET is not set
# CONFIG_POLLER is not set
# CONFIG_RESET_SOURCE is not set
#
# Debugging
#
CONFIG_COMPILE_LOGLEVEL=6
CONFIG_DEFAULT_LOGLEVEL=7
CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_LL is not set
CONFIG_DEBUG_OMAP_UART_PORT=1
# CONFIG_DEBUG_INITCALLS is not set
CONFIG_HAS_DEBUG_LL=y
CONFIG_COMMAND_SUPPORT=y
# CONFIG_HAS_POWEROFF is not set
CONFIG_COMPILE_DIGEST=y
CONFIG_COMPILE_MEMORY=y
#
# Commands
#
#
# Information
#
CONFIG_CMD_ARM_CPUINFO=y
CONFIG_CMD_DEVINFO=y
CONFIG_CMD_DRVINFO=y
CONFIG_CMD_HELP=y
CONFIG_LONGHELP=y
# CONFIG_CMD_IOMEM is not set
CONFIG_CMD_MEMINFO=y
CONFIG_CMD_ARM_MMUINFO=y
CONFIG_CMD_VERSION=y
#
# Boot
#
CONFIG_FLEXIBLE_BOOTARGS=y
CONFIG_CMD_BOOT=y
CONFIG_CMD_BOOTM=y
CONFIG_CMD_BOOTM_SHOW_TYPE=y
# CONFIG_CMD_BOOTM_VERBOSE is not set
# CONFIG_CMD_BOOTM_INITRD is not set
# CONFIG_CMD_BOOTM_OFTREE is not set
# CONFIG_CMD_BOOTM_AIMAGE is not set
CONFIG_CMD_BOOTU=y
CONFIG_CMD_BOOTZ=y
CONFIG_CMD_GO=y
CONFIG_CMD_LOADB=y
# CONFIG_CMD_LOADS is not set
# CONFIG_CMD_LOADY is not set
CONFIG_CMD_RESET=y
CONFIG_CMD_UIMAGE=y
#
# Partition
#
CONFIG_CMD_PARTITION=y
CONFIG_CMD_AUTOMOUNT=y
CONFIG_CMD_MOUNT=y
CONFIG_CMD_UBI=y
CONFIG_CMD_UBIFORMAT=y
CONFIG_CMD_UMOUNT=y
#
# Environment
#
CONFIG_CMD_EXPORT=y
CONFIG_CMD_GLOBAL=y
CONFIG_CMD_LOADENV=y
CONFIG_CMD_PRINTENV=y
# CONFIG_CMD_MAGICVAR is not set
CONFIG_CMD_SAVEENV=y
#
# File
#
CONFIG_CMD_BASENAME=y
CONFIG_CMD_CAT=y
CONFIG_CMD_CD=y
CONFIG_CMD_CP=y
CONFIG_CMD_DIRNAME=y
# CONFIG_CMD_FILETYPE is not set
# CONFIG_CMD_LN is not set
CONFIG_CMD_LS=y
CONFIG_CMD_MD5SUM=y
CONFIG_CMD_MKDIR=y
CONFIG_CMD_PWD=y
CONFIG_CMD_READLINK=y
CONFIG_CMD_RM=y
CONFIG_CMD_RMDIR=y
# CONFIG_CMD_SHA1SUM is not set
# CONFIG_CMD_SHA224SUM is not set
# CONFIG_CMD_SHA256SUM is not set
CONFIG_CMD_UNCOMPRESS=y
#
# Shell scripting
#
CONFIG_CMD_FALSE=y
CONFIG_CMD_GETOPT=y
# CONFIG_CMD_LET is not set
# CONFIG_CMD_MSLEEP is not set
# CONFIG_CMD_READF is not set
CONFIG_CMD_SLEEP=y
CONFIG_CMD_TEST=y
CONFIG_CMD_TRUE=y
#
# Network
#
# CONFIG_CMD_DHCP is not set
# CONFIG_CMD_HOST is not set
CONFIG_NET_CMD_IFUP=y
CONFIG_CMD_MIITOOL=y
# CONFIG_CMD_PING is not set
CONFIG_CMD_TFTP=y
#
# Console and Framebuffer interaction
#
CONFIG_CMD_CLEAR=y
CONFIG_CMD_ECHO=y
CONFIG_CMD_ECHO_E=y
CONFIG_CMD_EDIT=y
# CONFIG_CMD_LOGIN is not set
CONFIG_CMD_MENU=y
CONFIG_CMD_MENU_MANAGEMENT=y
# CONFIG_CMD_MENUTREE is not set
# CONFIG_CMD_PASSWD is not set
# CONFIG_CMD_SPLASH is not set
CONFIG_CMD_READLINE=y
CONFIG_CMD_TIMEOUT=y
#
# Memory
#
CONFIG_CMD_CRC=y
CONFIG_CMD_CRC_CMP=y
CONFIG_CMD_MD=y
CONFIG_CMD_MEMCMP=y
CONFIG_CMD_MEMCPY=y
CONFIG_CMD_MEMSET=y
CONFIG_CMD_MEMTEST=y
# CONFIG_CMD_MM is not set
CONFIG_CMD_MW=y
#
# Hardware manipulation
#
# CONFIG_CMD_DETECT is not set
CONFIG_CMD_FLASH=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_I2C=y
CONFIG_CMD_NAND=y
CONFIG_CMD_NANDTEST=y
CONFIG_CMD_USB=y
#
# Miscelleanous
#
# CONFIG_CMD_2048 is not set
CONFIG_CMD_BAREBOX_UPDATE=y
# CONFIG_CMD_OF_DUMP is not set
# CONFIG_CMD_OF_NODE is not set
# CONFIG_CMD_OF_PROPERTY is not set
# CONFIG_CMD_OFTREE is not set
CONFIG_CMD_TIME=y
CONFIG_NET=y
CONFIG_NET_NFS=y
# CONFIG_NET_NETCONSOLE is not set
# CONFIG_NET_RESOLV is not set
CONFIG_NET_IFUP=y
#
# Drivers
#
# CONFIG_OFDEVICE is not set
CONFIG_OF_NET=y
#
# serial drivers
#
# CONFIG_DRIVER_SERIAL_ARM_DCC is not set
CONFIG_DRIVER_SERIAL_NS16550=y
CONFIG_DRIVER_SERIAL_NS16550_OMAP_EXTENSIONS=y
# CONFIG_DRIVER_SERIAL_CADENCE is not set
CONFIG_PHYLIB=y
#
# Network drivers
#
# CONFIG_DRIVER_NET_ARC_EMAC is not set
# CONFIG_DRIVER_NET_CALXEDA_XGMAC is not set
CONFIG_DRIVER_NET_CPSW=y
# CONFIG_DRIVER_NET_DESIGNWARE is not set
# CONFIG_DRIVER_NET_ETHOC is not set
# CONFIG_DRIVER_NET_KS8851_MLL is not set
# CONFIG_DRIVER_NET_SMC911X is not set
# CONFIG_DRIVER_NET_SMC91111 is not set
#
# phylib
#
#
# MII PHY device drivers
#
# CONFIG_AT803X_PHY is not set
# CONFIG_LXT_PHY is not set
# CONFIG_MICREL_PHY is not set
# CONFIG_NATIONAL_PHY is not set
CONFIG_SMSC_PHY=y
#
# MII bus device drivers
#
# CONFIG_NET_USB is not set
#
# SPI drivers
#
# CONFIG_SPI is not set
CONFIG_I2C=y
#
# I2C Hardware Bus support
#
# CONFIG_I2C_GPIO is not set
CONFIG_I2C_OMAP=y
CONFIG_MTD=y
CONFIG_MTD_WRITE=y
CONFIG_MTD_OOB_DEVICE=y
# CONFIG_MTD_RAW_DEVICE is not set
#
# Self contained MTD devices
#
# CONFIG_MTD_DOCG3 is not set
# CONFIG_DRIVER_CFI is not set
CONFIG_NAND=y
CONFIG_NAND_ECC_SOFT=y
# CONFIG_NAND_ECC_BCH is not set
CONFIG_NAND_ECC_HW=y
# CONFIG_NAND_ECC_HW_OOB_FIRST is not set
CONFIG_NAND_ECC_HW_SYNDROME=y
CONFIG_NAND_ECC_HW_NONE=y
CONFIG_NAND_INFO=y
CONFIG_NAND_READ_OOB=y
CONFIG_NAND_BBT=y
# CONFIG_NAND_ALLOW_ERASE_BAD is not set
CONFIG_NAND_OMAP_GPMC=y
# CONFIG_MTD_NAND_ECC_SMC is not set
CONFIG_MTD_NAND_IDS=y
CONFIG_MTD_UBI=y
CONFIG_MTD_UBI_WL_THRESHOLD=4096
CONFIG_MTD_UBI_BEB_LIMIT=20
# CONFIG_MTD_UBI_FASTMAP is not set
CONFIG_DISK=y
CONFIG_DISK_WRITE=y
#
# drive types
#
# CONFIG_DISK_ATA is not set
# CONFIG_DISK_AHCI is not set
#
# interface types
#
# CONFIG_DISK_INTF_PLATFORM_IDE is not set
CONFIG_USB=y
# CONFIG_USB_EHCI is not set
# CONFIG_USB_ULPI is not set
# CONFIG_USB_STORAGE is not set
# CONFIG_VIDEO is not set
CONFIG_MCI=y
#
# --- Feature list ---
#
CONFIG_MCI_STARTUP=y
CONFIG_MCI_INFO=y
CONFIG_MCI_WRITE=y
# CONFIG_MCI_MMC_BOOT_PARTITIONS is not set
#
# --- MCI host drivers ---
#
# CONFIG_MCI_DW is not set
CONFIG_MCI_OMAP_HSMMC=y
# CONFIG_CLOCKSOURCE_DUMMY is not set
#
# MFD
#
# CONFIG_MFD_ACT8846 is not set
# CONFIG_MFD_LP3972 is not set
# CONFIG_MFD_MC13XXX is not set
# CONFIG_MFD_MC34704 is not set
# CONFIG_MFD_MC9SDZ60 is not set
# CONFIG_MFD_STMPE is not set
# CONFIG_MFD_SYSCON is not set
# CONFIG_MFD_TWL4030 is not set
# CONFIG_MFD_TWL6030 is not set
#
# Misc devices
#
# CONFIG_JTAG is not set
# CONFIG_SRAM is not set
# CONFIG_LED is not set
#
# EEPROM support
#
CONFIG_EEPROM_AT24=y
#
# Input device support
#
# CONFIG_KEYBOARD_GPIO is not set
# CONFIG_KEYBOARD_QT1070 is not set
# CONFIG_WATCHDOG is not set
# CONFIG_PWM is not set
#
# DMA support
#
CONFIG_GPIOLIB=y
#
# GPIO
#
CONFIG_GPIO_GENERIC=y
CONFIG_GPIO_GENERIC_PLATFORM=y
# CONFIG_GPIO_IMX is not set
CONFIG_GPIO_OMAP=y
# CONFIG_GPIO_DESIGNWARE is not set
# CONFIG_W1 is not set
# CONFIG_PINCTRL_SINGLE is not set
#
# Bus devices
#
# CONFIG_RESET_CONTROLLER is not set
#
# Filesystem support
#
CONFIG_FS=y
CONFIG_FS_AUTOMOUNT=y
# CONFIG_FS_CRAMFS is not set
CONFIG_FS_EXT4=y
CONFIG_FS_RAMFS=y
CONFIG_FS_DEVFS=y
CONFIG_FS_TFTP=y
CONFIG_FS_NFS=y
CONFIG_FS_FAT=y
CONFIG_FS_FAT_WRITE=y
CONFIG_FS_FAT_LFN=y
# CONFIG_FS_UBIFS is not set
# CONFIG_FS_BPKFS is not set
# CONFIG_FS_UIMAGEFS is not set
#
# Library routines
#
CONFIG_PARAMETER=y
CONFIG_UNCOMPRESS=y
CONFIG_ZLIB=y
# CONFIG_BZLIB is not set
# CONFIG_LZ4_DECOMPRESS is not set
# CONFIG_GENERIC_FIND_NEXT_BIT is not set
CONFIG_PROCESS_ESCAPE_SEQUENCE=y
CONFIG_LZO_DECOMPRESS=y
CONFIG_QSORT=y
CONFIG_LIBSCAN=y
CONFIG_LIBUBIGEN=y
CONFIG_LIBMTD=y
#
# Library gui routines
#
CONFIG_CRC32=y
CONFIG_CRC16=y
CONFIG_DIGEST=y
CONFIG_MD5=y
# CONFIG_SHA1 is not set
# CONFIG_SHA224 is not set
# CONFIG_SHA256 is not set
[-- Attachment #3: barebox_mlo.config --]
[-- Type: text/plain, Size: 6594 bytes --]
#
# Automatically generated file; DO NOT EDIT.
# Barebox/arm 2014.07.0 Configuration
#
CONFIG_ARM=y
#
# System Type
#
# CONFIG_ARCH_AT91 is not set
# CONFIG_ARCH_BCM2835 is not set
# CONFIG_ARCH_CLPS711X is not set
# CONFIG_ARCH_DAVINCI is not set
# CONFIG_ARCH_EP93XX is not set
# CONFIG_ARCH_HIGHBANK is not set
# CONFIG_ARCH_IMX is not set
# CONFIG_ARCH_MVEBU is not set
# CONFIG_ARCH_MXS is not set
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_NOMADIK is not set
CONFIG_ARCH_OMAP=y
# CONFIG_ARCH_PXA is not set
# CONFIG_ARCH_ROCKCHIP is not set
# CONFIG_ARCH_SOCFPGA is not set
# CONFIG_ARCH_S3C24xx is not set
# CONFIG_ARCH_S5PCxx is not set
# CONFIG_ARCH_S3C64xx is not set
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_VEXPRESS is not set
# CONFIG_ARCH_TEGRA is not set
# CONFIG_ARCH_UEMD is not set
# CONFIG_ARCH_ZYNQ is not set
#
# Processor Type
#
CONFIG_CPU_32=y
CONFIG_CPU_V7=y
CONFIG_CPU_32v7=y
#
# processor features
#
# CONFIG_BOOT_ENDIANNESS_SWITCH is not set
CONFIG_BAREBOX_MAX_IMAGE_SIZE=0xffffffff
#
# OMAP Features
#
CONFIG_ARCH_AM33XX=y
CONFIG_OMAP_CLOCK_SOURCE_DMTIMER0=y
CONFIG_OMAP_GPMC=y
CONFIG_OMAP_BUILD_IFT=y
# CONFIG_OMAP_BUILD_SPI is not set
CONFIG_OMAP_MULTI_BOARDS=y
# CONFIG_MACH_BEAGLEBONE is not set
CONFIG_MACH_PCM051=y
CONFIG_ARM_ASM_UNIFIED=y
CONFIG_AEABI=y
CONFIG_THUMB2_BAREBOX=y
#
# ARM specific settings
#
# CONFIG_CPU_V7_DCACHE_SKIP is not set
# CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS is not set
CONFIG_ARM_EXCEPTIONS=y
# CONFIG_ARM_UNWIND is not set
CONFIG_DEFCONFIG_LIST="$ARCH_DEFCONFIG"
CONFIG_HAS_KALLSYMS=y
CONFIG_HAS_MODULES=y
CONFIG_GENERIC_GPIO=y
CONFIG_BLOCK=y
CONFIG_BLOCK_WRITE=y
CONFIG_FILETYPE=y
#
# General Settings
#
CONFIG_LOCALVERSION="-PD13.0.0 phyBOARD-WEGA MLO"
CONFIG_LOCALVERSION_AUTO=y
CONFIG_BANNER=y
# CONFIG_MEMINFO is not set
CONFIG_ENVIRONMENT_VARIABLES=y
#
# memory layout
#
CONFIG_HAVE_PBL_IMAGE=y
CONFIG_HAVE_PBL_MULTI_IMAGES=y
CONFIG_HAVE_IMAGE_COMPRESSION=y
CONFIG_PBL_IMAGE=y
CONFIG_PBL_MULTI_IMAGES=y
CONFIG_PBL_RELOCATABLE=y
CONFIG_IMAGE_COMPRESSION=y
# CONFIG_IMAGE_COMPRESSION_LZ4 is not set
CONFIG_IMAGE_COMPRESSION_LZO=y
# CONFIG_IMAGE_COMPRESSION_GZIP is not set
# CONFIG_IMAGE_COMPRESSION_NONE is not set
CONFIG_MMU=y
CONFIG_MMU_EARLY=y
CONFIG_HAVE_CONFIGURABLE_TEXT_BASE=y
CONFIG_TEXT_BASE=0x402F0400
CONFIG_BAREBOX_MAX_PBL_SIZE=0xffffffff
CONFIG_BAREBOX_MAX_BARE_INIT_SIZE=0xffffffff
CONFIG_STACK_SIZE=0x1600
CONFIG_MALLOC_SIZE=0x1000000
# CONFIG_BROKEN is not set
# CONFIG_EXPERIMENTAL is not set
CONFIG_MALLOC_DLMALLOC=y
# CONFIG_MALLOC_TLSF is not set
# CONFIG_MALLOC_DUMMY is not set
# CONFIG_KALLSYMS is not set
# CONFIG_RELOCATABLE is not set
# CONFIG_PANIC_HANG is not set
CONFIG_PROMPT="MLO>"
CONFIG_BAUDRATE=115200
CONFIG_SIMPLE_READLINE=y
CONFIG_CBSIZE=1024
# CONFIG_SHELL_HUSH is not set
# CONFIG_SHELL_SIMPLE is not set
CONFIG_SHELL_NONE=y
# CONFIG_GLOB is not set
# CONFIG_MENU is not set
# CONFIG_PASSWORD is not set
# CONFIG_ERRNO_MESSAGES is not set
# CONFIG_TIMESTAMP is not set
# CONFIG_BLSPEC is not set
# CONFIG_KERNEL_INSTALL_TARGET is not set
# CONFIG_CONSOLE_FULL is not set
CONFIG_CONSOLE_SIMPLE=y
# CONFIG_CONSOLE_NONE is not set
CONFIG_PARTITION=y
CONFIG_PARTITION_DISK=y
CONFIG_PARTITION_DISK_DOS=y
# CONFIG_PARTITION_DISK_EFI is not set
# CONFIG_DEFAULT_ENVIRONMENT is not set
CONFIG_DEFAULT_COMPRESSION_NONE=y
CONFIG_HAVE_DEFAULT_ENVIRONMENT_NEW=y
# CONFIG_BAREBOXENV_TARGET is not set
# CONFIG_BAREBOXCRC32_TARGET is not set
# CONFIG_POLLER is not set
#
# Debugging
#
CONFIG_COMPILE_LOGLEVEL=6
CONFIG_DEFAULT_LOGLEVEL=7
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_LL is not set
CONFIG_DEBUG_OMAP_UART_PORT=1
# CONFIG_DEBUG_INITCALLS is not set
CONFIG_HAS_DEBUG_LL=y
# CONFIG_HAS_POWEROFF is not set
# CONFIG_NET is not set
#
# Drivers
#
# CONFIG_OFDEVICE is not set
#
# serial drivers
#
# CONFIG_DRIVER_SERIAL_ARM_DCC is not set
CONFIG_DRIVER_SERIAL_NS16550=y
CONFIG_DRIVER_SERIAL_NS16550_OMAP_EXTENSIONS=y
# CONFIG_DRIVER_SERIAL_CADENCE is not set
#
# SPI drivers
#
# CONFIG_SPI is not set
# CONFIG_I2C is not set
CONFIG_MTD=y
CONFIG_MTD_WRITE=y
CONFIG_MTD_OOB_DEVICE=y
# CONFIG_MTD_RAW_DEVICE is not set
#
# Self contained MTD devices
#
# CONFIG_MTD_DOCG3 is not set
# CONFIG_DRIVER_CFI is not set
CONFIG_NAND=y
CONFIG_NAND_ECC_SOFT=y
# CONFIG_NAND_ECC_BCH is not set
CONFIG_NAND_ECC_HW=y
# CONFIG_NAND_ECC_HW_OOB_FIRST is not set
CONFIG_NAND_ECC_HW_SYNDROME=y
# CONFIG_NAND_ECC_HW_NONE is not set
CONFIG_NAND_INFO=y
CONFIG_NAND_READ_OOB=y
CONFIG_NAND_BBT=y
# CONFIG_NAND_ALLOW_ERASE_BAD is not set
CONFIG_NAND_OMAP_GPMC=y
# CONFIG_MTD_NAND_ECC_SMC is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_UBI is not set
CONFIG_DISK=y
CONFIG_DISK_WRITE=y
#
# drive types
#
# CONFIG_DISK_ATA is not set
# CONFIG_DISK_AHCI is not set
#
# interface types
#
# CONFIG_DISK_INTF_PLATFORM_IDE is not set
# CONFIG_USB is not set
# CONFIG_VIDEO is not set
CONFIG_MCI=y
#
# --- Feature list ---
#
CONFIG_MCI_STARTUP=y
# CONFIG_MCI_WRITE is not set
# CONFIG_MCI_MMC_BOOT_PARTITIONS is not set
#
# --- MCI host drivers ---
#
# CONFIG_MCI_DW is not set
CONFIG_MCI_OMAP_HSMMC=y
# CONFIG_CLOCKSOURCE_DUMMY is not set
#
# MFD
#
# CONFIG_MFD_SYSCON is not set
#
# Misc devices
#
# CONFIG_JTAG is not set
# CONFIG_SRAM is not set
# CONFIG_LED is not set
#
# EEPROM support
#
#
# Input device support
#
# CONFIG_KEYBOARD_GPIO is not set
# CONFIG_WATCHDOG is not set
# CONFIG_PWM is not set
#
# DMA support
#
CONFIG_GPIOLIB=y
#
# GPIO
#
# CONFIG_GPIO_GENERIC_PLATFORM is not set
# CONFIG_GPIO_IMX is not set
CONFIG_GPIO_OMAP=y
# CONFIG_GPIO_DESIGNWARE is not set
# CONFIG_W1 is not set
# CONFIG_PINCTRL_SINGLE is not set
#
# Bus devices
#
# CONFIG_RESET_CONTROLLER is not set
#
# Filesystem support
#
CONFIG_FS=y
# CONFIG_FS_CRAMFS is not set
# CONFIG_FS_EXT4 is not set
# CONFIG_FS_RAMFS is not set
# CONFIG_FS_DEVFS is not set
CONFIG_FS_FAT=y
# CONFIG_FS_FAT_WRITE is not set
CONFIG_FS_FAT_LFN=y
# CONFIG_FS_BPKFS is not set
# CONFIG_FS_UIMAGEFS is not set
#
# Library routines
#
# CONFIG_ZLIB is not set
# CONFIG_BZLIB is not set
# CONFIG_LZ4_DECOMPRESS is not set
# CONFIG_GENERIC_FIND_NEXT_BIT is not set
# CONFIG_PROCESS_ESCAPE_SEQUENCE is not set
# CONFIG_LZO_DECOMPRESS is not set
#
# Library gui routines
#
# CONFIG_BOOTSTRAP is not set
# CONFIG_DIGEST is not set
[-- Attachment #4: Type: text/plain, Size: 149 bytes --]
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Problems with pyhBoard-Wega-AM335x
[not found] ` <53BA5442.6020708@ma-info.de>
2014-07-07 8:04 ` Frede Florian
@ 2014-07-07 10:05 ` Rolf Evers-Fischer
2014-07-07 11:14 ` Frede Florian
1 sibling, 1 reply; 15+ messages in thread
From: Rolf Evers-Fischer @ 2014-07-07 10:05 UTC (permalink / raw)
To: Florian Frede; +Cc: barebox, Rolf Evers-Fischer
Hello Florian,
On Mon, 7 Jul 2014, Florian Frede wrote:
> Hello Rolf,
>
> I used this Option already, but to be sure that there is no mistake I
> reconfigured the Barebox and Barebox_MLO again and use the new Version
> 2014.07.0. The result is the same.
>
>
> I also attached the config files may be there is an other error?
>
thank you for the config files.
Please enable in both configs (barebox and barebox_mlo):
"Drivers" -> "Enable probing of devices from the devicetree".
Kind regards,
Rolf
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Problems with pyhBoard-Wega-AM335x
2014-07-07 10:05 ` Rolf Evers-Fischer
@ 2014-07-07 11:14 ` Frede Florian
2014-07-07 12:00 ` Sascha Hauer
0 siblings, 1 reply; 15+ messages in thread
From: Frede Florian @ 2014-07-07 11:14 UTC (permalink / raw)
To: Rolf Evers-Fischer; +Cc: barebox
Hello Rolf,
thank you very much...
after I selected the mentioned entry in the menu the problem was solved...
but the board do not prompt any thing on the UART1... so I do not know
if barebox is loaded
from the sd-card or not...
Regards Florian
Am 07.07.2014 12:05, schrieb Rolf Evers-Fischer:
> Hello Florian,
>
> On Mon, 7 Jul 2014, Florian Frede wrote:
>
>> [...]
> thank you for the config files.
>
> Please enable in both configs (barebox and barebox_mlo):
> "Drivers" -> "Enable probing of devices from the devicetree".
>
> Kind regards,
> Rolf
>
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Problems with pyhBoard-Wega-AM335x
2014-07-07 11:14 ` Frede Florian
@ 2014-07-07 12:00 ` Sascha Hauer
2014-07-07 12:04 ` Robert P. J. Day
2014-07-07 12:29 ` Rolf Evers-Fischer
0 siblings, 2 replies; 15+ messages in thread
From: Sascha Hauer @ 2014-07-07 12:00 UTC (permalink / raw)
To: Frede Florian; +Cc: barebox, Rolf Evers-Fischer
On Mon, Jul 07, 2014 at 01:14:35PM +0200, Frede Florian wrote:
> Hello Rolf,
>
> thank you very much...
> after I selected the mentioned entry in the menu the problem was solved...
> but the board do not prompt any thing on the UART1... so I do not
> know if barebox is loaded
When using mainline barebox please build the am335x_mlo_defconfig for
the MLO and the am335x_defconfig for the main binary. The images
are then found under:
images/barebox-am33xx-phytec-phycore-mlo.img
images/barebox-am33xx-phytec-phycore.img
I diffed you config against the mainline config and the following
options are really crucial to let the binary work correctly:
-CONFIG_TEXT_BASE=0x0
-CONFIG_MALLOC_SIZE=0x0
-CONFIG_MALLOC_TLSF=y
-CONFIG_RELOCATABLE=y
+CONFIG_TEXT_BASE=0x402F0400
+CONFIG_STACK_SIZE=0x1600
+CONFIG_MALLOC_SIZE=0x1000000
Sascha
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Problems with pyhBoard-Wega-AM335x
2014-07-07 12:00 ` Sascha Hauer
@ 2014-07-07 12:04 ` Robert P. J. Day
2014-07-07 12:16 ` Sascha Hauer
2014-07-07 12:29 ` Rolf Evers-Fischer
1 sibling, 1 reply; 15+ messages in thread
From: Robert P. J. Day @ 2014-07-07 12:04 UTC (permalink / raw)
To: Sascha Hauer; +Cc: Rolf Evers-Fischer, barebox
On Mon, 7 Jul 2014, Sascha Hauer wrote:
> On Mon, Jul 07, 2014 at 01:14:35PM +0200, Frede Florian wrote:
> > Hello Rolf,
> >
> > thank you very much...
> > after I selected the mentioned entry in the menu the problem was solved...
> > but the board do not prompt any thing on the UART1... so I do not
> > know if barebox is loaded
>
> When using mainline barebox please build the am335x_mlo_defconfig for
> the MLO and the am335x_defconfig for the main binary. The images
> are then found under:
from memory, i noticed earlier that when i configured for
am335x_defconfig, then did "make menuconfig", i was asked whether i
wanted to build the MLO file as well. does that mean i can generate
both the MLO and second stage from a single build? or am i
misunderstanding what i saw?
rday
--
========================================================================
Robert P. J. Day Ottawa, Ontario, CANADA
http://crashcourse.ca
Twitter: http://twitter.com/rpjday
LinkedIn: http://ca.linkedin.com/in/rpjday
========================================================================
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Problems with pyhBoard-Wega-AM335x
2014-07-07 12:04 ` Robert P. J. Day
@ 2014-07-07 12:16 ` Sascha Hauer
0 siblings, 0 replies; 15+ messages in thread
From: Sascha Hauer @ 2014-07-07 12:16 UTC (permalink / raw)
To: Robert P. J. Day; +Cc: Rolf Evers-Fischer, barebox
On Mon, Jul 07, 2014 at 08:04:55AM -0400, Robert P. J. Day wrote:
> On Mon, 7 Jul 2014, Sascha Hauer wrote:
>
> > On Mon, Jul 07, 2014 at 01:14:35PM +0200, Frede Florian wrote:
> > > Hello Rolf,
> > >
> > > thank you very much...
> > > after I selected the mentioned entry in the menu the problem was solved...
> > > but the board do not prompt any thing on the UART1... so I do not
> > > know if barebox is loaded
> >
> > When using mainline barebox please build the am335x_mlo_defconfig for
> > the MLO and the am335x_defconfig for the main binary. The images
> > are then found under:
>
> from memory, i noticed earlier that when i configured for
> am335x_defconfig, then did "make menuconfig", i was asked whether i
> wanted to build the MLO file as well. does that mean i can generate
> both the MLO and second stage from a single build? or am i
> misunderstanding what i saw?
The option has no effect when OMAP_MULTI_BOARDS is enabled which is the
case for the am335x boards. I just sent out a patch to hide the options.
Sascha
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Problems with pyhBoard-Wega-AM335x
2014-07-07 12:00 ` Sascha Hauer
2014-07-07 12:04 ` Robert P. J. Day
@ 2014-07-07 12:29 ` Rolf Evers-Fischer
2014-07-08 9:29 ` Frede Florian
1 sibling, 1 reply; 15+ messages in thread
From: Rolf Evers-Fischer @ 2014-07-07 12:29 UTC (permalink / raw)
To: florian.frede; +Cc: barebox
Hello Florian,
> Sascha Hauer <s.hauer@pengutronix.de> hat am 7. Juli 2014 um 14:00
> geschrieben:
>
>
> On Mon, Jul 07, 2014 at 01:14:35PM +0200, Frede Florian wrote:
> > Hello Rolf,
> >
> > thank you very much...
> > after I selected the mentioned entry in the menu the problem was solved...
> > but the board do not prompt any thing on the UART1... so I do not
> > know if barebox is loaded
>
> When using mainline barebox please build the am335x_mlo_defconfig for
> the MLO and the am335x_defconfig for the main binary. The images
> are then found under:
>
> images/barebox-am33xx-phytec-phycore-mlo.img
> images/barebox-am33xx-phytec-phycore.img
>
> I diffed you config against the mainline config and the following
> options are really crucial to let the binary work correctly:
>
> -CONFIG_TEXT_BASE=0x0
> -CONFIG_MALLOC_SIZE=0x0
> -CONFIG_MALLOC_TLSF=y
> -CONFIG_RELOCATABLE=y
> +CONFIG_TEXT_BASE=0x402F0400
> +CONFIG_STACK_SIZE=0x1600
> +CONFIG_MALLOC_SIZE=0x1000000
>
in fact, these settings are essential.
If you still can't see anything, you can also enable the config item "Debugging"
-> "low level debug messages". With this option enabled, you should at least see
a '>' on UART1 right after power-on. This character will be output at the end of
function pcm051_board_init().
If you like to debug the further startup, you could also enable the "Debugging"
-> "Trace initcalls" option in barebox_mlo config.
Best regards,
Rolf
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Problems with pyhBoard-Wega-AM335x
2014-07-07 12:29 ` Rolf Evers-Fischer
@ 2014-07-08 9:29 ` Frede Florian
2014-07-08 10:01 ` Teresa Gamez
0 siblings, 1 reply; 15+ messages in thread
From: Frede Florian @ 2014-07-08 9:29 UTC (permalink / raw)
To: Rolf Evers-Fischer; +Cc: barebox
Hello Rolf,
Hello Sascha,
I tried your hints... but I don't get the prompt ">" after a while my
Desktop-PC say that a Ethernet connection is established thats all I can
not ping or connect to the pyhBoard-Wega-AM335x. But nothing is
transmitted on the Evaluation Board (PEB-EVAL-01). Do I need some
patches or something else?
Sorry but I have no idea which information I can send you to help me
with my problem...
Thanks again
Florian
Am 07.07.2014 14:29, schrieb Rolf Evers-Fischer:
> Hello Florian,
>
>> Sascha Hauer <s.hauer@pengutronix.de> hat am 7. Juli 2014 um 14:00
>> geschrieben:
>>
>>
>> On Mon, Jul 07, 2014 at 01:14:35PM +0200, Frede Florian wrote:
>>> Hello Rolf,
>>>
>>> thank you very much...
>>> after I selected the mentioned entry in the menu the problem was solved...
>>> but the board do not prompt any thing on the UART1... so I do not
>>> know if barebox is loaded
>> When using mainline barebox please build the am335x_mlo_defconfig for
>> the MLO and the am335x_defconfig for the main binary. The images
>> are then found under:
>>
>> images/barebox-am33xx-phytec-phycore-mlo.img
>> images/barebox-am33xx-phytec-phycore.img
>>
>> I diffed you config against the mainline config and the following
>> options are really crucial to let the binary work correctly:
>>
>> -CONFIG_TEXT_BASE=0x0
>> -CONFIG_MALLOC_SIZE=0x0
>> -CONFIG_MALLOC_TLSF=y
>> -CONFIG_RELOCATABLE=y
>> +CONFIG_TEXT_BASE=0x402F0400
>> +CONFIG_STACK_SIZE=0x1600
>> +CONFIG_MALLOC_SIZE=0x1000000
>>
> in fact, these settings are essential.
> If you still can't see anything, you can also enable the config item "Debugging"
> -> "low level debug messages". With this option enabled, you should at least see
> a '>' on UART1 right after power-on. This character will be output at the end of
> function pcm051_board_init().
> If you like to debug the further startup, you could also enable the "Debugging"
> -> "Trace initcalls" option in barebox_mlo config.
>
> Best regards,
> Rolf
>
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Problems with pyhBoard-Wega-AM335x
2014-07-08 9:29 ` Frede Florian
@ 2014-07-08 10:01 ` Teresa Gamez
2014-07-09 6:47 ` Rolf Evers-Fischer
0 siblings, 1 reply; 15+ messages in thread
From: Teresa Gamez @ 2014-07-08 10:01 UTC (permalink / raw)
To: Frede Florian; +Cc: barebox, Rolf Evers-Fischer
Hello Florian,
I guess you having the default kit WEGA, which does have 256MB RAM. The mainline supported
phyCORE Kit does have 512MB. Thats probably why it does not start up.
I'll have a look at it.
Teresa
Am Dienstag, den 08.07.2014, 11:29 +0200 schrieb Frede Florian:
> Hello Rolf,
> Hello Sascha,
>
> I tried your hints... but I don't get the prompt ">" after a while my
> Desktop-PC say that a Ethernet connection is established thats all I can
> not ping or connect to the pyhBoard-Wega-AM335x. But nothing is
> transmitted on the Evaluation Board (PEB-EVAL-01). Do I need some
> patches or something else?
>
> Sorry but I have no idea which information I can send you to help me
> with my problem...
>
> Thanks again
>
> Florian
>
> Am 07.07.2014 14:29, schrieb Rolf Evers-Fischer:
> > Hello Florian,
> >
> >> Sascha Hauer <s.hauer@pengutronix.de> hat am 7. Juli 2014 um 14:00
> >> geschrieben:
> >>
> >>
> >> On Mon, Jul 07, 2014 at 01:14:35PM +0200, Frede Florian wrote:
> >>> Hello Rolf,
> >>>
> >>> thank you very much...
> >>> after I selected the mentioned entry in the menu the problem was solved...
> >>> but the board do not prompt any thing on the UART1... so I do not
> >>> know if barebox is loaded
> >> When using mainline barebox please build the am335x_mlo_defconfig for
> >> the MLO and the am335x_defconfig for the main binary. The images
> >> are then found under:
> >>
> >> images/barebox-am33xx-phytec-phycore-mlo.img
> >> images/barebox-am33xx-phytec-phycore.img
> >>
> >> I diffed you config against the mainline config and the following
> >> options are really crucial to let the binary work correctly:
> >>
> >> -CONFIG_TEXT_BASE=0x0
> >> -CONFIG_MALLOC_SIZE=0x0
> >> -CONFIG_MALLOC_TLSF=y
> >> -CONFIG_RELOCATABLE=y
> >> +CONFIG_TEXT_BASE=0x402F0400
> >> +CONFIG_STACK_SIZE=0x1600
> >> +CONFIG_MALLOC_SIZE=0x1000000
> >>
> > in fact, these settings are essential.
> > If you still can't see anything, you can also enable the config item "Debugging"
> > -> "low level debug messages". With this option enabled, you should at least see
> > a '>' on UART1 right after power-on. This character will be output at the end of
> > function pcm051_board_init().
> > If you like to debug the further startup, you could also enable the "Debugging"
> > -> "Trace initcalls" option in barebox_mlo config.
> >
> > Best regards,
> > Rolf
> >
>
>
> _______________________________________________
> barebox mailing list
> barebox@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Problems with pyhBoard-Wega-AM335x
2014-07-08 10:01 ` Teresa Gamez
@ 2014-07-09 6:47 ` Rolf Evers-Fischer
2014-07-09 12:32 ` Frede Florian
0 siblings, 1 reply; 15+ messages in thread
From: Rolf Evers-Fischer @ 2014-07-09 6:47 UTC (permalink / raw)
To: Teresa Gamez; +Cc: Rolf Evers-Fischer, barebox
Hello Florian,
On Tue, 8 Jul 2014, Teresa Gamez wrote:
> Hello Florian,
>
> I guess you having the default kit WEGA, which does have 256MB RAM. The mainline supported
> phyCORE Kit does have 512MB. Thats probably why it does not start up.
>
> I'll have a look at it.
>
> Teresa
>
I'm not 100% sure, but I can imagine that the ">" should also appear when
the SDRAM configuration is not correct. But nevertheless the correct
SDRAM setting is important. Maybe, you can check the SDRAM setting of your
previous barebox-2013.11. I assume, the old barebox was running properly,
wasn't it?
> > Sorry but I have no idea which information I can send you to help me
> > with my problem...
> >
Florian, could you please check the size of your 1st stage bootloader
(MLO) binary?
It must not exceed 111616 byte! Otherwise it will not boot.
You can shrink the size by removing all unnecessary stuff from the
barebox_mlo configuration.
Best regards,
Rolf
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Problems with pyhBoard-Wega-AM335x
2014-07-09 6:47 ` Rolf Evers-Fischer
@ 2014-07-09 12:32 ` Frede Florian
2014-07-21 9:34 ` Frede Florian
0 siblings, 1 reply; 15+ messages in thread
From: Frede Florian @ 2014-07-09 12:32 UTC (permalink / raw)
To: Rolf Evers-Fischer, Teresa Gamez; +Cc: barebox
Hello Rolf,
after I apply the Patch from Teresa I got the ">".
Yes the last barebox worked. Yesterday I configured the new barebox in
the same way as the old one and got the ">" the size of my image is only
93260 bytes so it should work but it do not work. So I will spend no
more time with the phyWega and wait for the phyCore Kit and start there
my next try.
Thanks for your helping
Florian
Am 09.07.2014 08:47, schrieb Rolf Evers-Fischer:
> Hello Florian,
>
> On Tue, 8 Jul 2014, Teresa Gamez wrote:
>
>> Hello Florian,
>>
>> I guess you having the default kit WEGA, which does have 256MB RAM. The mainline supported
>> phyCORE Kit does have 512MB. Thats probably why it does not start up.
>>
>> I'll have a look at it.
>>
>> Teresa
>>
> I'm not 100% sure, but I can imagine that the ">" should also appear when
> the SDRAM configuration is not correct. But nevertheless the correct
> SDRAM setting is important. Maybe, you can check the SDRAM setting of your
> previous barebox-2013.11. I assume, the old barebox was running properly,
> wasn't it?
>
>>> Sorry but I have no idea which information I can send you to help me
>>> with my problem...
>>>
> Florian, could you please check the size of your 1st stage bootloader
> (MLO) binary?
> It must not exceed 111616 byte! Otherwise it will not boot.
> You can shrink the size by removing all unnecessary stuff from the
> barebox_mlo configuration.
>
> Best regards,
> Rolf
>
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Problems with pyhBoard-Wega-AM335x
2014-07-09 12:32 ` Frede Florian
@ 2014-07-21 9:34 ` Frede Florian
2014-07-22 7:20 ` Holger Schurig
0 siblings, 1 reply; 15+ messages in thread
From: Frede Florian @ 2014-07-21 9:34 UTC (permalink / raw)
To: barebox
[-- Attachment #1: Type: text/plain, Size: 374 bytes --]
Hello...
now I have a working Barebox 2014.07 on the pyhCore...
* I used the attached configuration
* Generated a patch to the git (commit
9d7b0ba957a665d6013c4fa53df04ac324618a40)
* For NAND support it is important to enable *CONFIG_BUS_OMAP_GPMC*
after that the Barebox starts and boots the Linux Kernel from my SD-Card...
Thanks for everyone
Florian
[-- Attachment #2: barebox.config --]
[-- Type: text/plain, Size: 11946 bytes --]
#
# Automatically generated file; DO NOT EDIT.
# Barebox/arm 2014.07.0 Configuration
#
CONFIG_ARM=y
CONFIG_ARM_LINUX=y
#
# System Type
#
# CONFIG_BUILTIN_DTB is not set
# CONFIG_ARCH_AT91 is not set
# CONFIG_ARCH_BCM2835 is not set
# CONFIG_ARCH_CLPS711X is not set
# CONFIG_ARCH_DAVINCI is not set
# CONFIG_ARCH_EP93XX is not set
# CONFIG_ARCH_HIGHBANK is not set
# CONFIG_ARCH_IMX is not set
# CONFIG_ARCH_MVEBU is not set
# CONFIG_ARCH_MXS is not set
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_NOMADIK is not set
CONFIG_ARCH_OMAP=y
# CONFIG_ARCH_PXA is not set
# CONFIG_ARCH_ROCKCHIP is not set
# CONFIG_ARCH_SOCFPGA is not set
# CONFIG_ARCH_S3C24xx is not set
# CONFIG_ARCH_S5PCxx is not set
# CONFIG_ARCH_S3C64xx is not set
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_VEXPRESS is not set
# CONFIG_ARCH_TEGRA is not set
# CONFIG_ARCH_UEMD is not set
# CONFIG_ARCH_ZYNQ is not set
#
# Processor Type
#
CONFIG_CPU_32=y
CONFIG_CPU_V7=y
CONFIG_CPU_32v7=y
#
# processor features
#
# CONFIG_BOOT_ENDIANNESS_SWITCH is not set
CONFIG_BAREBOX_MAX_IMAGE_SIZE=0xffffffff
#
# OMAP Features
#
CONFIG_ARCH_AM33XX=y
CONFIG_OMAP_CLOCK_SOURCE_DMTIMER0=y
CONFIG_OMAP_GPMC=y
# CONFIG_OMAP_BUILD_IFT is not set
# CONFIG_OMAP_BUILD_SPI is not set
CONFIG_BAREBOX_UPDATE_AM33XX_SPI_NOR_MLO=y
# CONFIG_BAREBOX_UPDATE_AM33XX_NAND_XLOADSLOTS is not set
CONFIG_OMAP_MULTI_BOARDS=y
# CONFIG_MACH_BEAGLEBONE is not set
CONFIG_MACH_PCM051=y
CONFIG_ARM_ASM_UNIFIED=y
CONFIG_AEABI=y
CONFIG_THUMB2_BAREBOX=y
CONFIG_ARM_BOARD_APPEND_ATAG=y
#
# ARM specific settings
#
# CONFIG_CPU_V7_DCACHE_SKIP is not set
CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y
CONFIG_ARM_EXCEPTIONS=y
CONFIG_ARM_UNWIND=y
CONFIG_DEFCONFIG_LIST="$ARCH_DEFCONFIG"
CONFIG_HAS_KALLSYMS=y
CONFIG_HAS_MODULES=y
CONFIG_ENV_HANDLING=y
CONFIG_GENERIC_GPIO=y
CONFIG_BOOTM=y
CONFIG_BLOCK=y
CONFIG_BLOCK_WRITE=y
CONFIG_FILETYPE=y
CONFIG_BINFMT=y
CONFIG_UIMAGE=y
CONFIG_GLOBALVAR=y
CONFIG_STDDEV=y
CONFIG_BAREBOX_UPDATE=y
CONFIG_MENUTREE=y
#
# General Settings
#
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
CONFIG_BANNER=y
CONFIG_MEMINFO=y
CONFIG_ENVIRONMENT_VARIABLES=y
#
# memory layout
#
CONFIG_HAVE_PBL_IMAGE=y
CONFIG_HAVE_PBL_MULTI_IMAGES=y
CONFIG_HAVE_IMAGE_COMPRESSION=y
CONFIG_PBL_IMAGE=y
CONFIG_PBL_MULTI_IMAGES=y
CONFIG_PBL_RELOCATABLE=y
CONFIG_IMAGE_COMPRESSION=y
# CONFIG_IMAGE_COMPRESSION_LZ4 is not set
CONFIG_IMAGE_COMPRESSION_LZO=y
# CONFIG_IMAGE_COMPRESSION_GZIP is not set
# CONFIG_IMAGE_COMPRESSION_NONE is not set
CONFIG_MMU=y
CONFIG_MMU_EARLY=y
CONFIG_HAVE_CONFIGURABLE_TEXT_BASE=y
CONFIG_TEXT_BASE=0x0
CONFIG_BAREBOX_MAX_PBL_SIZE=0xffffffff
CONFIG_BAREBOX_MAX_BARE_INIT_SIZE=0xffffffff
CONFIG_STACK_SIZE=0x8000
CONFIG_MALLOC_SIZE=0x0
# CONFIG_BROKEN is not set
# CONFIG_EXPERIMENTAL is not set
# CONFIG_MALLOC_DLMALLOC is not set
CONFIG_MALLOC_TLSF=y
CONFIG_KALLSYMS=y
CONFIG_RELOCATABLE=y
# CONFIG_PANIC_HANG is not set
CONFIG_PROMPT="barebox> "
CONFIG_BAUDRATE=115200
CONFIG_CBSIZE=1024
CONFIG_SHELL_HUSH=y
# CONFIG_SHELL_SIMPLE is not set
# CONFIG_SHELL_NONE is not set
CONFIG_GLOB=y
CONFIG_GLOB_SORT=y
CONFIG_PROMPT_HUSH_PS2="> "
CONFIG_HUSH_FANCY_PROMPT=y
CONFIG_CMDLINE_EDITING=y
CONFIG_AUTO_COMPLETE=y
CONFIG_MENU=y
# CONFIG_PASSWORD is not set
CONFIG_DYNAMIC_CRC_TABLE=y
CONFIG_ERRNO_MESSAGES=y
# CONFIG_TIMESTAMP is not set
CONFIG_BLSPEC=y
# CONFIG_KERNEL_INSTALL_TARGET is not set
CONFIG_CONSOLE_FULL=y
# CONFIG_CONSOLE_SIMPLE is not set
# CONFIG_CONSOLE_NONE is not set
# CONFIG_CONSOLE_ACTIVATE_FIRST is not set
# CONFIG_CONSOLE_ACTIVATE_ALL is not set
CONFIG_CONSOLE_ACTIVATE_NONE=y
CONFIG_PARTITION=y
CONFIG_PARTITION_DISK=y
CONFIG_PARTITION_DISK_DOS=y
# CONFIG_PARTITION_DISK_EFI is not set
CONFIG_DEFAULT_ENVIRONMENT=y
CONFIG_DEFAULT_COMPRESSION_NONE=y
CONFIG_HAVE_DEFAULT_ENVIRONMENT_NEW=y
CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW=y
CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW_MENU=y
CONFIG_DEFAULT_ENVIRONMENT_PATH=""
# CONFIG_BAREBOXENV_TARGET is not set
# CONFIG_BAREBOXCRC32_TARGET is not set
CONFIG_POLLER=y
# CONFIG_RESET_SOURCE is not set
#
# Debugging
#
CONFIG_COMPILE_LOGLEVEL=6
CONFIG_DEFAULT_LOGLEVEL=7
CONFIG_DEBUG_INFO=y
CONFIG_DEBUG_LL=y
CONFIG_DEBUG_AM33XX_UART=y
CONFIG_DEBUG_OMAP_UART_PORT=0
# CONFIG_DEBUG_INITCALLS is not set
CONFIG_HAS_DEBUG_LL=y
CONFIG_COMMAND_SUPPORT=y
# CONFIG_HAS_POWEROFF is not set
CONFIG_COMPILE_DIGEST=y
CONFIG_COMPILE_MEMORY=y
#
# Commands
#
#
# Information
#
CONFIG_CMD_ARM_CPUINFO=y
CONFIG_CMD_DEVINFO=y
CONFIG_CMD_DRVINFO=y
CONFIG_CMD_HELP=y
CONFIG_LONGHELP=y
CONFIG_CMD_IOMEM=y
CONFIG_CMD_MEMINFO=y
CONFIG_CMD_ARM_MMUINFO=y
CONFIG_CMD_VERSION=y
#
# Boot
#
CONFIG_FLEXIBLE_BOOTARGS=y
CONFIG_CMD_BOOT=y
CONFIG_CMD_BOOTM=y
CONFIG_CMD_BOOTM_SHOW_TYPE=y
CONFIG_CMD_BOOTM_VERBOSE=y
CONFIG_CMD_BOOTM_INITRD=y
CONFIG_CMD_BOOTM_OFTREE=y
# CONFIG_CMD_BOOTM_OFTREE_UIMAGE is not set
# CONFIG_CMD_BOOTM_AIMAGE is not set
# CONFIG_CMD_BOOTU is not set
CONFIG_CMD_BOOTZ=y
CONFIG_CMD_GO=y
CONFIG_CMD_LOADB=y
# CONFIG_CMD_LOADS is not set
# CONFIG_CMD_LOADY is not set
CONFIG_CMD_RESET=y
CONFIG_CMD_UIMAGE=y
#
# Partition
#
CONFIG_CMD_PARTITION=y
CONFIG_CMD_AUTOMOUNT=y
CONFIG_CMD_MOUNT=y
CONFIG_CMD_UBI=y
CONFIG_CMD_UBIFORMAT=y
CONFIG_CMD_UMOUNT=y
#
# Environment
#
CONFIG_CMD_EXPORT=y
CONFIG_CMD_GLOBAL=y
CONFIG_CMD_LOADENV=y
CONFIG_CMD_PRINTENV=y
CONFIG_CMD_MAGICVAR=y
CONFIG_CMD_MAGICVAR_HELP=y
CONFIG_CMD_SAVEENV=y
#
# File
#
CONFIG_CMD_BASENAME=y
CONFIG_CMD_CAT=y
CONFIG_CMD_CD=y
CONFIG_CMD_CP=y
CONFIG_CMD_DIRNAME=y
CONFIG_CMD_FILETYPE=y
CONFIG_CMD_LN=y
CONFIG_CMD_LS=y
CONFIG_CMD_MD5SUM=y
CONFIG_CMD_MKDIR=y
CONFIG_CMD_PWD=y
CONFIG_CMD_READLINK=y
CONFIG_CMD_RM=y
CONFIG_CMD_RMDIR=y
# CONFIG_CMD_SHA1SUM is not set
# CONFIG_CMD_SHA224SUM is not set
# CONFIG_CMD_SHA256SUM is not set
CONFIG_CMD_UNCOMPRESS=y
#
# Shell scripting
#
CONFIG_CMD_FALSE=y
CONFIG_CMD_GETOPT=y
CONFIG_CMD_LET=y
CONFIG_CMD_MSLEEP=y
CONFIG_CMD_READF=y
CONFIG_CMD_SLEEP=y
CONFIG_CMD_TEST=y
CONFIG_CMD_TRUE=y
#
# Network
#
CONFIG_CMD_DHCP=y
CONFIG_CMD_HOST=y
CONFIG_NET_CMD_IFUP=y
CONFIG_CMD_MIITOOL=y
CONFIG_CMD_PING=y
CONFIG_CMD_TFTP=y
#
# Console and Framebuffer interaction
#
CONFIG_CMD_CLEAR=y
CONFIG_CMD_ECHO=y
CONFIG_CMD_ECHO_E=y
CONFIG_CMD_EDIT=y
# CONFIG_CMD_LOGIN is not set
CONFIG_CMD_MENU=y
# CONFIG_CMD_MENU_MANAGEMENT is not set
CONFIG_CMD_MENUTREE=y
# CONFIG_CMD_PASSWD is not set
# CONFIG_CMD_SPLASH is not set
CONFIG_CMD_READLINE=y
CONFIG_CMD_TIMEOUT=y
#
# Memory
#
CONFIG_CMD_CRC=y
CONFIG_CMD_CRC_CMP=y
CONFIG_CMD_MD=y
CONFIG_CMD_MEMCMP=y
CONFIG_CMD_MEMCPY=y
CONFIG_CMD_MEMSET=y
# CONFIG_CMD_MEMTEST is not set
CONFIG_CMD_MM=y
CONFIG_CMD_MW=y
#
# Hardware manipulation
#
CONFIG_CMD_DETECT=y
CONFIG_CMD_FLASH=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_I2C=y
CONFIG_CMD_NAND=y
# CONFIG_CMD_NANDTEST is not set
CONFIG_CMD_SPI=y
CONFIG_CMD_USB=y
#
# Miscelleanous
#
# CONFIG_CMD_2048 is not set
CONFIG_CMD_BAREBOX_UPDATE=y
CONFIG_CMD_OF_DUMP=y
CONFIG_CMD_OF_NODE=y
CONFIG_CMD_OF_PROPERTY=y
CONFIG_CMD_OFTREE=y
CONFIG_CMD_TIME=y
CONFIG_NET=y
CONFIG_NET_NFS=y
CONFIG_NET_NETCONSOLE=y
CONFIG_NET_RESOLV=y
CONFIG_NET_IFUP=y
#
# Drivers
#
CONFIG_OFTREE=y
CONFIG_OFTREE_MEM_GENERIC=y
CONFIG_DTC=y
CONFIG_OFDEVICE=y
CONFIG_OF_NET=y
CONFIG_OF_GPIO=y
CONFIG_OF_BAREBOX_DRIVERS=y
#
# serial drivers
#
# CONFIG_DRIVER_SERIAL_ARM_DCC is not set
CONFIG_DRIVER_SERIAL_NS16550=y
CONFIG_DRIVER_SERIAL_NS16550_OMAP_EXTENSIONS=y
# CONFIG_DRIVER_SERIAL_CADENCE is not set
CONFIG_PHYLIB=y
#
# Network drivers
#
# CONFIG_DRIVER_NET_ARC_EMAC is not set
# CONFIG_DRIVER_NET_CALXEDA_XGMAC is not set
CONFIG_DRIVER_NET_CPSW=y
# CONFIG_DRIVER_NET_DESIGNWARE is not set
# CONFIG_DRIVER_NET_ENC28J60 is not set
# CONFIG_DRIVER_NET_ETHOC is not set
# CONFIG_DRIVER_NET_KS8851_MLL is not set
# CONFIG_DRIVER_NET_MICREL is not set
# CONFIG_DRIVER_NET_SMC911X is not set
# CONFIG_DRIVER_NET_SMC91111 is not set
#
# phylib
#
#
# MII PHY device drivers
#
# CONFIG_AT803X_PHY is not set
# CONFIG_LXT_PHY is not set
# CONFIG_MARVELL_PHY is not set
# CONFIG_MICREL_PHY is not set
# CONFIG_NATIONAL_PHY is not set
CONFIG_SMSC_PHY=y
#
# MII bus device drivers
#
# CONFIG_NET_USB is not set
#
# SPI drivers
#
CONFIG_SPI=y
CONFIG_DRIVER_SPI_OMAP3=y
CONFIG_I2C=y
CONFIG_I2C_ALGOBIT=y
#
# I2C Hardware Bus support
#
CONFIG_I2C_GPIO=y
CONFIG_I2C_OMAP=y
CONFIG_MTD=y
CONFIG_MTD_WRITE=y
CONFIG_MTD_OOB_DEVICE=y
# CONFIG_MTD_RAW_DEVICE is not set
#
# Self contained MTD devices
#
# CONFIG_MTD_DATAFLASH is not set
CONFIG_MTD_M25P80=y
# CONFIG_MTD_SST25L is not set
# CONFIG_MTD_DOCG3 is not set
# CONFIG_DRIVER_CFI is not set
CONFIG_NAND=y
CONFIG_NAND_ECC_SOFT=y
# CONFIG_NAND_ECC_BCH is not set
CONFIG_NAND_ECC_HW=y
# CONFIG_NAND_ECC_HW_OOB_FIRST is not set
CONFIG_NAND_ECC_HW_SYNDROME=y
CONFIG_NAND_ECC_HW_NONE=y
CONFIG_NAND_INFO=y
CONFIG_NAND_READ_OOB=y
CONFIG_NAND_BBT=y
# CONFIG_NAND_ALLOW_ERASE_BAD is not set
CONFIG_NAND_OMAP_GPMC=y
# CONFIG_MTD_NAND_ECC_SMC is not set
CONFIG_MTD_NAND_IDS=y
CONFIG_MTD_UBI=y
CONFIG_MTD_UBI_WL_THRESHOLD=4096
CONFIG_MTD_UBI_BEB_LIMIT=20
# CONFIG_MTD_UBI_FASTMAP is not set
CONFIG_DISK=y
CONFIG_DISK_WRITE=y
#
# drive types
#
# CONFIG_DISK_ATA is not set
# CONFIG_DISK_AHCI is not set
#
# interface types
#
# CONFIG_DISK_INTF_PLATFORM_IDE is not set
CONFIG_USB=y
# CONFIG_USB_EHCI is not set
# CONFIG_USB_ULPI is not set
# CONFIG_USB_STORAGE is not set
# CONFIG_VIDEO is not set
CONFIG_MCI=y
#
# --- Feature list ---
#
CONFIG_MCI_STARTUP=y
CONFIG_MCI_INFO=y
CONFIG_MCI_WRITE=y
# CONFIG_MCI_MMC_BOOT_PARTITIONS is not set
#
# --- MCI host drivers ---
#
# CONFIG_MCI_DW is not set
CONFIG_MCI_OMAP_HSMMC=y
# CONFIG_MCI_SPI is not set
# CONFIG_CLOCKSOURCE_DUMMY is not set
#
# MFD
#
# CONFIG_MFD_ACT8846 is not set
# CONFIG_MFD_LP3972 is not set
# CONFIG_MFD_MC13XXX is not set
# CONFIG_MFD_MC34704 is not set
# CONFIG_MFD_MC9SDZ60 is not set
# CONFIG_MFD_STMPE is not set
# CONFIG_MFD_SYSCON is not set
# CONFIG_MFD_TWL4030 is not set
# CONFIG_MFD_TWL6030 is not set
#
# Misc devices
#
# CONFIG_JTAG is not set
# CONFIG_SRAM is not set
# CONFIG_LED is not set
#
# EEPROM support
#
# CONFIG_EEPROM_AT25 is not set
CONFIG_EEPROM_AT24=y
#
# Input device support
#
# CONFIG_KEYBOARD_GPIO is not set
# CONFIG_KEYBOARD_QT1070 is not set
# CONFIG_WATCHDOG is not set
# CONFIG_PWM is not set
#
# DMA support
#
CONFIG_GPIOLIB=y
#
# GPIO
#
CONFIG_GPIO_GENERIC=y
CONFIG_GPIO_GENERIC_PLATFORM=y
# CONFIG_GPIO_IMX is not set
CONFIG_GPIO_OMAP=y
# CONFIG_GPIO_DESIGNWARE is not set
# CONFIG_W1 is not set
CONFIG_PINCTRL=y
CONFIG_PINCTRL_SINGLE=y
#
# Bus devices
#
CONFIG_BUS_OMAP_GPMC=y
# CONFIG_REGULATOR is not set
# CONFIG_RESET_CONTROLLER is not set
#
# Filesystem support
#
CONFIG_FS=y
CONFIG_FS_AUTOMOUNT=y
# CONFIG_FS_CRAMFS is not set
CONFIG_FS_EXT4=y
CONFIG_FS_RAMFS=y
CONFIG_FS_DEVFS=y
CONFIG_FS_TFTP=y
CONFIG_FS_NFS=y
CONFIG_FS_FAT=y
CONFIG_FS_FAT_WRITE=y
CONFIG_FS_FAT_LFN=y
# CONFIG_FS_UBIFS is not set
# CONFIG_FS_BPKFS is not set
# CONFIG_FS_UIMAGEFS is not set
#
# Library routines
#
CONFIG_PARAMETER=y
CONFIG_UNCOMPRESS=y
# CONFIG_ZLIB is not set
# CONFIG_BZLIB is not set
# CONFIG_LZ4_DECOMPRESS is not set
# CONFIG_GENERIC_FIND_NEXT_BIT is not set
CONFIG_PROCESS_ESCAPE_SEQUENCE=y
# CONFIG_LZO_DECOMPRESS is not set
CONFIG_QSORT=y
CONFIG_LIBSCAN=y
CONFIG_LIBUBIGEN=y
CONFIG_LIBMTD=y
#
# Library gui routines
#
CONFIG_CRC32=y
CONFIG_CRC16=y
CONFIG_DIGEST=y
CONFIG_MD5=y
# CONFIG_SHA1 is not set
# CONFIG_SHA224 is not set
# CONFIG_SHA256 is not set
[-- Attachment #3: Type: text/plain, Size: 149 bytes --]
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: Problems with pyhBoard-Wega-AM335x
2014-07-21 9:34 ` Frede Florian
@ 2014-07-22 7:20 ` Holger Schurig
0 siblings, 0 replies; 15+ messages in thread
From: Holger Schurig @ 2014-07-22 7:20 UTC (permalink / raw)
To: Frede Florian; +Cc: barebox
> * For NAND support it is important to enable *CONFIG_BUS_OMAP_GPMC*
If this is something that is mandatory for the board, maybe the board
should then select it in the Kconfig?
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 15+ messages in thread
* Problems with pyhBoard-Wega-AM335x
@ 2014-07-04 10:12 Frede Florian
0 siblings, 0 replies; 15+ messages in thread
From: Frede Florian @ 2014-07-04 10:12 UTC (permalink / raw)
To: barebox
Hello,
I like to update from barebox 2013.11 to barebox 2014.06.0 with the
phyBoard-Wega-AM335x. After reconfigure the barebox I get the error:
LD images/start_am33xx_phytec_phycore_sram.pbl
arch/arm/boards/built-in-pbl.o: In function `pcm051_board_init':
:(.text.pcm051_board_init+0x94): undefined reference to
`__dtb_am335x_phytec_phycore_start'
make[2]: *** [images/start_am33xx_phytec_phycore_sram.pbl] Error 1
make[1]: *** [images] Error 2
Thanks for Helping
Florian
--
Best regards / Mit freundlichen Grüßen
Florian Frede
____________________________________________
company name: Dr. Mergenthaler GmbH & Co. KG
contact: Dipl. Informatiker Florian Frede
position: Embedded Software Engineer
street: Lilienthalstraße 14
zip code: 89231
city: Neu-Ulm
country: Germany
fon: +49 (0)7 31 - 15 97 90 40
fax: +49 (0)7 31 - 15 97 90 46
mailto: florian.frede@ma-info.de
internet: www.ma-info.de
____________________________________________
Dr. Mergenthaler GmbH & Co. KG
Sitz Neu-Ulm, Registergericht Memmingen, HRA12084
Geschäftsführer: Dr. Detlev Mergenthaler
persönlich haftende Gesellschafterin:
Dr. Mergenthaler Verwaltungsgesellschaft mbH
Sitz Neu-Ulm, Registergericht Memmingen, HRA14622
Steuer-Nr. 151/156/03504
Ust-Id-Nr. DE237130366
____________________________________________
Diese E-Mail einschließlich ihrer Anhänge enthält vertrauliche und/oder rechtlich geschützte Informationen. Wenn Sie nicht der richtige Adressat sind oder diese E-Mail irrtümlich erhalten haben, informieren Sie bitte sofort den Absender und vernichten Sie diese E-Mail. Das unerlaubte Kopieren sowie die unbefugte Weitergabe dieser Mail oder von Teilen dieser Mail ist nicht gestattet.
---
This e-mail including its attachments contains confidential and/or privileged information. If you are not the intended recipient or have received this e-mail in error please, notify the sender immediately and destroy this e-mail. Any unauthorised copying, disclosure or distribution of the material in this e-mail or of parts hereof is strictly forbidden.
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 15+ messages in thread
end of thread, other threads:[~2014-07-22 7:20 UTC | newest]
Thread overview: 15+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-07-04 13:26 Problems with pyhBoard-Wega-AM335x Rolf Evers-Fischer
[not found] ` <53BA5442.6020708@ma-info.de>
2014-07-07 8:04 ` Frede Florian
2014-07-07 10:05 ` Rolf Evers-Fischer
2014-07-07 11:14 ` Frede Florian
2014-07-07 12:00 ` Sascha Hauer
2014-07-07 12:04 ` Robert P. J. Day
2014-07-07 12:16 ` Sascha Hauer
2014-07-07 12:29 ` Rolf Evers-Fischer
2014-07-08 9:29 ` Frede Florian
2014-07-08 10:01 ` Teresa Gamez
2014-07-09 6:47 ` Rolf Evers-Fischer
2014-07-09 12:32 ` Frede Florian
2014-07-21 9:34 ` Frede Florian
2014-07-22 7:20 ` Holger Schurig
-- strict thread matches above, loose matches on Subject: below --
2014-07-04 10:12 Frede Florian
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox