* [PATCH v2 0/1] gpio: add driver for xilinx zynq and zynqmp
@ 2021-10-13 11:22 Michael Riesch
2021-10-13 11:22 ` [PATCH v2 1/1] " Michael Riesch
2021-10-14 11:57 ` [PATCH v2 0/1] " Sascha Hauer
0 siblings, 2 replies; 3+ messages in thread
From: Michael Riesch @ 2021-10-13 11:22 UTC (permalink / raw)
To: barebox; +Cc: Michael Riesch
Hi all,
This patch adds a GPIO driver for the Xilinx Zynq/Zynq
UltraScale+ MPSoC architecture based on the corresponding
driver in the Linux kernel.
The work was mainly carried out by Thomas Haemmerle, with
several format fixes and the revisions for v2 applied by me.
Version 2 of this patch considers the review by Ahmad
Fatoum.
Tested on the ZCU106 evaluation board as well as on a
custom Zynq UltraScale+ MPSoC board.
Best regards,
Michael
Thomas Haemmerle (1):
gpio: add driver for xilinx zynq and zynqmp
arch/arm/Kconfig | 2 +
arch/arm/configs/zynq_defconfig | 1 +
arch/arm/configs/zynqmp_defconfig | 1 +
drivers/gpio/Kconfig | 7 +
drivers/gpio/Makefile | 1 +
drivers/gpio/gpio-zynq.c | 436 ++++++++++++++++++++++++++++++
6 files changed, 448 insertions(+)
create mode 100644 drivers/gpio/gpio-zynq.c
--
2.17.1
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 3+ messages in thread
* [PATCH v2 1/1] gpio: add driver for xilinx zynq and zynqmp
2021-10-13 11:22 [PATCH v2 0/1] gpio: add driver for xilinx zynq and zynqmp Michael Riesch
@ 2021-10-13 11:22 ` Michael Riesch
2021-10-14 11:57 ` [PATCH v2 0/1] " Sascha Hauer
1 sibling, 0 replies; 3+ messages in thread
From: Michael Riesch @ 2021-10-13 11:22 UTC (permalink / raw)
To: barebox; +Cc: Thomas Haemmerle, Michael Riesch
From: Thomas Haemmerle <thomas.haemmerle@wolfvision.net>
Port the driver for the Xilinx Zynq/Zynq UltraScale+ MPSoC architecture
to barebox (based on the Linux driver).
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@wolfvision.net>
[apply format fixes, revise probe function, revise Kconfig]
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
---
v2:
- add CONFIG_GPIO_ZYNQ=y to zynq{mp}_defconfig
- revise Kconfig
- revise and clean up probe function
arch/arm/Kconfig | 2 +
arch/arm/configs/zynq_defconfig | 1 +
arch/arm/configs/zynqmp_defconfig | 1 +
drivers/gpio/Kconfig | 7 +
drivers/gpio/Makefile | 1 +
drivers/gpio/gpio-zynq.c | 436 ++++++++++++++++++++++++++++++
6 files changed, 448 insertions(+)
create mode 100644 drivers/gpio/gpio-zynq.c
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index c7ab16688..a8b7bdeaa 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -248,6 +248,7 @@ config ARCH_ZYNQ
bool "Xilinx Zynq-based boards"
select HAS_DEBUG_LL
select PBL_IMAGE
+ select GPIOLIB
config ARCH_ZYNQMP
bool "Xilinx ZynqMP-based boards"
@@ -258,6 +259,7 @@ config ARCH_ZYNQMP
select COMMON_CLK
select COMMON_CLK_OF_PROVIDER
select CLKDEV_LOOKUP
+ select GPIOLIB
select OFDEVICE
select OFTREE
select RELOCATABLE
diff --git a/arch/arm/configs/zynq_defconfig b/arch/arm/configs/zynq_defconfig
index a16c57d5c..38662eeb5 100644
--- a/arch/arm/configs/zynq_defconfig
+++ b/arch/arm/configs/zynq_defconfig
@@ -45,3 +45,4 @@ CONFIG_DRIVER_NET_MACB=y
# CONFIG_PINCTRL is not set
CONFIG_FS_TFTP=y
CONFIG_DIGEST=y
+CONFIG_GPIO_ZYNQ=y
diff --git a/arch/arm/configs/zynqmp_defconfig b/arch/arm/configs/zynqmp_defconfig
index 2cd878133..8dd0f40b3 100644
--- a/arch/arm/configs/zynqmp_defconfig
+++ b/arch/arm/configs/zynqmp_defconfig
@@ -64,3 +64,4 @@ CONFIG_FS_NFS=y
CONFIG_FS_FAT=y
CONFIG_FS_FAT_WRITE=y
CONFIG_DIGEST=y
+CONFIG_GPIO_ZYNQ=y
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index f79c9ea67..347a719f5 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -197,6 +197,13 @@ config GPIO_LIBFTDI1
bool "libftdi1 driver"
depends on SANDBOX
+config GPIO_ZYNQ
+ tristate "Xilinx Zynq GPIO support"
+ depends on ARCH_ZYNQ || ARCH_ZYNQMP || CROSS_COMPILE
+ depends on OFDEVICE
+ help
+ Say yes here to support Xilinx Zynq GPIO controller.
+
endmenu
endif
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 023973cb6..d9f96e34c 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -26,3 +26,4 @@ obj-$(CONFIG_GPIO_VF610) += gpio-vf610.o
obj-$(CONFIG_GPIO_RASPBERRYPI_EXP) += gpio-raspberrypi-exp.o
obj-$(CONFIG_GPIO_SIFIVE) += gpio-sifive.o
obj-$(CONFIG_GPIO_STARFIVE) += gpio-starfive-vic.o
+obj-$(CONFIG_GPIO_ZYNQ) += gpio-zynq.o
diff --git a/drivers/gpio/gpio-zynq.c b/drivers/gpio/gpio-zynq.c
new file mode 100644
index 000000000..bb7785761
--- /dev/null
+++ b/drivers/gpio/gpio-zynq.c
@@ -0,0 +1,436 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Xilinx Zynq GPIO device driver
+ *
+ * Copyright (C) 2009 - 2014 Xilinx, Inc.
+ *
+ * Based on the Linux kernel driver (drivers/gpio/gpio-zynq.c).
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <gpio.h>
+#include <init.h>
+#include <io.h>
+#include <of.h>
+
+/* Maximum banks */
+#define ZYNQ_GPIO_MAX_BANK 4
+#define ZYNQMP_GPIO_MAX_BANK 6
+
+#define ZYNQ_GPIO_BANK0_NGPIO 32
+#define ZYNQ_GPIO_BANK1_NGPIO 22
+#define ZYNQ_GPIO_BANK2_NGPIO 32
+#define ZYNQ_GPIO_BANK3_NGPIO 32
+
+#define ZYNQMP_GPIO_BANK0_NGPIO 26
+#define ZYNQMP_GPIO_BANK1_NGPIO 26
+#define ZYNQMP_GPIO_BANK2_NGPIO 26
+#define ZYNQMP_GPIO_BANK3_NGPIO 32
+#define ZYNQMP_GPIO_BANK4_NGPIO 32
+#define ZYNQMP_GPIO_BANK5_NGPIO 32
+
+#define ZYNQ_GPIO_NR_GPIOS 118
+#define ZYNQMP_GPIO_NR_GPIOS 174
+
+#define ZYNQ_GPIO_BANK0_PIN_MIN(str) 0
+#define ZYNQ_GPIO_BANK0_PIN_MAX(str) \
+ (ZYNQ_GPIO_BANK0_PIN_MIN(str) + ZYNQ##str##_GPIO_BANK0_NGPIO - 1)
+#define ZYNQ_GPIO_BANK1_PIN_MIN(str) (ZYNQ_GPIO_BANK0_PIN_MAX(str) + 1)
+#define ZYNQ_GPIO_BANK1_PIN_MAX(str) \
+ (ZYNQ_GPIO_BANK1_PIN_MIN(str) + ZYNQ##str##_GPIO_BANK1_NGPIO - 1)
+#define ZYNQ_GPIO_BANK2_PIN_MIN(str) (ZYNQ_GPIO_BANK1_PIN_MAX(str) + 1)
+#define ZYNQ_GPIO_BANK2_PIN_MAX(str) \
+ (ZYNQ_GPIO_BANK2_PIN_MIN(str) + ZYNQ##str##_GPIO_BANK2_NGPIO - 1)
+#define ZYNQ_GPIO_BANK3_PIN_MIN(str) (ZYNQ_GPIO_BANK2_PIN_MAX(str) + 1)
+#define ZYNQ_GPIO_BANK3_PIN_MAX(str) \
+ (ZYNQ_GPIO_BANK3_PIN_MIN(str) + ZYNQ##str##_GPIO_BANK3_NGPIO - 1)
+#define ZYNQ_GPIO_BANK4_PIN_MIN(str) (ZYNQ_GPIO_BANK3_PIN_MAX(str) + 1)
+#define ZYNQ_GPIO_BANK4_PIN_MAX(str) \
+ (ZYNQ_GPIO_BANK4_PIN_MIN(str) + ZYNQ##str##_GPIO_BANK4_NGPIO - 1)
+#define ZYNQ_GPIO_BANK5_PIN_MIN(str) (ZYNQ_GPIO_BANK4_PIN_MAX(str) + 1)
+#define ZYNQ_GPIO_BANK5_PIN_MAX(str) \
+ (ZYNQ_GPIO_BANK5_PIN_MIN(str) + ZYNQ##str##_GPIO_BANK5_NGPIO - 1)
+
+/* Register offsets for the GPIO device */
+/* LSW Mask & Data -WO */
+#define ZYNQ_GPIO_DATA_LSW_OFFSET(BANK) (0x000 + (8 * BANK))
+/* MSW Mask & Data -WO */
+#define ZYNQ_GPIO_DATA_MSW_OFFSET(BANK) (0x004 + (8 * BANK))
+/* Data Register-RW */
+#define ZYNQ_GPIO_DATA_OFFSET(BANK) (0x040 + (4 * BANK))
+#define ZYNQ_GPIO_DATA_RO_OFFSET(BANK) (0x060 + (4 * BANK))
+/* Direction mode reg-RW */
+#define ZYNQ_GPIO_DIRM_OFFSET(BANK) (0x204 + (0x40 * BANK))
+/* Output enable reg-RW */
+#define ZYNQ_GPIO_OUTEN_OFFSET(BANK) (0x208 + (0x40 * BANK))
+/* Interrupt mask reg-RO */
+#define ZYNQ_GPIO_INTMASK_OFFSET(BANK) (0x20C + (0x40 * BANK))
+/* Interrupt enable reg-WO */
+#define ZYNQ_GPIO_INTEN_OFFSET(BANK) (0x210 + (0x40 * BANK))
+/* Interrupt disable reg-WO */
+#define ZYNQ_GPIO_INTDIS_OFFSET(BANK) (0x214 + (0x40 * BANK))
+/* Interrupt status reg-RO */
+#define ZYNQ_GPIO_INTSTS_OFFSET(BANK) (0x218 + (0x40 * BANK))
+/* Interrupt type reg-RW */
+#define ZYNQ_GPIO_INTTYPE_OFFSET(BANK) (0x21C + (0x40 * BANK))
+/* Interrupt polarity reg-RW */
+#define ZYNQ_GPIO_INTPOL_OFFSET(BANK) (0x220 + (0x40 * BANK))
+/* Interrupt on any, reg-RW */
+#define ZYNQ_GPIO_INTANY_OFFSET(BANK) (0x224 + (0x40 * BANK))
+
+/* Disable all interrupts mask */
+#define ZYNQ_GPIO_IXR_DISABLE_ALL 0xFFFFFFFF
+
+/* Mid pin number of a bank */
+#define ZYNQ_GPIO_MID_PIN_NUM 16
+
+/* GPIO upper 16 bit mask */
+#define ZYNQ_GPIO_UPPER_MASK 0xFFFF0000
+
+/* set to differentiate zynq from zynqmp, 0=zynqmp, 1=zynq */
+#define ZYNQ_GPIO_QUIRK_IS_ZYNQ BIT(0)
+#define GPIO_QUIRK_DATA_RO_BUG BIT(1)
+
+/**
+ * struct zynq_gpio - GPIO device private data structure
+ * @chip: instance of the gpio_chip
+ * @base_addr: base address of the GPIO device
+ * @p_data: pointer to platform data
+ */
+struct zynq_gpio {
+ struct gpio_chip chip;
+ void __iomem *base_addr;
+ const struct zynq_platform_data *p_data;
+};
+
+/**
+ * struct zynq_platform_data - Zynq GPIO platform data structure
+ * @quirks: Flags is used to identify the platform
+ * @ngpio: max number of gpio pins
+ * @max_bank: maximum number of gpio banks
+ * @bank_min: this array represents bank's min pin
+ * @bank_max: this array represents bank's max pin
+ */
+struct zynq_platform_data {
+ u32 quirks;
+ u16 ngpio;
+ int max_bank;
+ int bank_min[ZYNQMP_GPIO_MAX_BANK];
+ int bank_max[ZYNQMP_GPIO_MAX_BANK];
+};
+
+/**
+ * zynq_gpio_is_zynq - Test if HW is Zynq or ZynqMP
+ * @gpio: Pointer to driver data struct
+ *
+ * Return: 0 if ZynqMP, 1 if Zynq.
+ */
+static int zynq_gpio_is_zynq(struct zynq_gpio *gpio)
+{
+ return !!(gpio->p_data->quirks & ZYNQ_GPIO_QUIRK_IS_ZYNQ);
+}
+
+/**
+ * gpio_data_ro_bug - Test if HW bug exists or not
+ * @gpio: Pointer to driver data struct
+ *
+ * Return: 0 if bug does not exist, 1 if bug exists.
+ */
+static int gpio_data_ro_bug(struct zynq_gpio *gpio)
+{
+ return !!(gpio->p_data->quirks & GPIO_QUIRK_DATA_RO_BUG);
+}
+
+/**
+ * zynq_gpio_get_bank_pin - Get the bank number and pin number within that bank
+ * for a given pin in the GPIO device
+ * @pin_num: gpio pin number within the device
+ * @bank_num: an output parameter used to return the bank number of the gpio
+ * pin
+ * @bank_pin_num: an output parameter used to return pin number within a bank
+ * for the given gpio pin
+ * @gpio: gpio device data structure
+ *
+ * Returns the bank number and pin offset within the bank.
+ */
+static int zynq_gpio_get_bank_pin(unsigned int pin_num, unsigned int *bank_num,
+ unsigned int *bank_pin_num,
+ struct zynq_gpio *gpio)
+{
+ int bank;
+
+ for (bank = 0; bank < gpio->p_data->max_bank; bank++) {
+ if ((pin_num >= gpio->p_data->bank_min[bank]) &&
+ (pin_num <= gpio->p_data->bank_max[bank])) {
+ *bank_num = bank;
+ *bank_pin_num = pin_num - gpio->p_data->bank_min[bank];
+ return 0;
+ }
+ }
+
+ *bank_num = 0;
+ *bank_pin_num = 0;
+ return -ENODEV;
+}
+
+/**
+ * zynq_gpio_get_value - Get the state of the specified pin of GPIO device
+ * @chip: gpio_chip instance to be worked on
+ * @pin: gpio pin number within the device
+ *
+ * This function reads the state of the specified pin of the GPIO device.
+ *
+ * Return: 0 if the pin is low, 1 if pin is high.
+ */
+static int zynq_gpio_get_value(struct gpio_chip *chip, unsigned int pin)
+{
+ u32 data;
+ unsigned int bank_num, bank_pin_num;
+ struct zynq_gpio *gpio = container_of(chip, struct zynq_gpio, chip);
+
+ if (zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio) < 0)
+ return -EINVAL;
+
+ if (gpio_data_ro_bug(gpio)) {
+ if (zynq_gpio_is_zynq(gpio)) {
+ if (bank_num <= 1) {
+ data = readl_relaxed(
+ gpio->base_addr +
+ ZYNQ_GPIO_DATA_RO_OFFSET(bank_num));
+ } else {
+ data = readl_relaxed(
+ gpio->base_addr +
+ ZYNQ_GPIO_DATA_OFFSET(bank_num));
+ }
+ } else {
+ if (bank_num <= 2) {
+ data = readl_relaxed(
+ gpio->base_addr +
+ ZYNQ_GPIO_DATA_RO_OFFSET(bank_num));
+ } else {
+ data = readl_relaxed(
+ gpio->base_addr +
+ ZYNQ_GPIO_DATA_OFFSET(bank_num));
+ }
+ }
+ } else {
+ data = readl_relaxed(gpio->base_addr +
+ ZYNQ_GPIO_DATA_RO_OFFSET(bank_num));
+ }
+ return (data >> bank_pin_num) & 1;
+}
+
+/**
+ * zynq_gpio_set_value - Modify the state of the pin with specified value
+ * @chip: gpio_chip instance to be worked on
+ * @pin: gpio pin number within the device
+ * @state: value used to modify the state of the specified pin
+ *
+ * This function calculates the register offset (i.e to lower 16 bits or
+ * upper 16 bits) based on the given pin number and sets the state of a
+ * gpio pin to the specified value. The state is either 0 or non-zero.
+ */
+static void zynq_gpio_set_value(struct gpio_chip *chip, unsigned int pin,
+ int state)
+{
+ unsigned int reg_offset, bank_num, bank_pin_num;
+ struct zynq_gpio *gpio = container_of(chip, struct zynq_gpio, chip);
+
+ if (zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio) < 0)
+ return;
+
+ if (bank_pin_num >= ZYNQ_GPIO_MID_PIN_NUM) {
+ bank_pin_num -= ZYNQ_GPIO_MID_PIN_NUM;
+ reg_offset = ZYNQ_GPIO_DATA_MSW_OFFSET(bank_num);
+ } else {
+ reg_offset = ZYNQ_GPIO_DATA_LSW_OFFSET(bank_num);
+ }
+
+ /*
+ * get the 32 bit value to be written to the mask/data register where
+ * the upper 16 bits is the mask and lower 16 bits is the data
+ */
+ state = !!state;
+ state = ~(1 << (bank_pin_num + ZYNQ_GPIO_MID_PIN_NUM)) &
+ ((state << bank_pin_num) | ZYNQ_GPIO_UPPER_MASK);
+
+ writel_relaxed(state, gpio->base_addr + reg_offset);
+}
+
+/**
+ * zynq_gpio_dir_in - Set the direction of the specified GPIO pin as input
+ * @chip: gpio_chip instance to be worked on
+ * @pin: gpio pin number within the device
+ *
+ * This function uses the read-modify-write sequence to set the direction of
+ * the gpio pin as input.
+ *
+ * Return: 0 always
+ */
+static int zynq_gpio_dir_in(struct gpio_chip *chip, unsigned int pin)
+{
+ u32 reg;
+ unsigned int bank_num, bank_pin_num;
+ struct zynq_gpio *gpio = container_of(chip, struct zynq_gpio, chip);
+
+ if (zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio) < 0)
+ return -EINVAL;
+ /*
+ * On zynq bank 0 pins 7 and 8 are special and cannot be used
+ * as inputs.
+ */
+ if (zynq_gpio_is_zynq(gpio) && bank_num == 0 &&
+ (bank_pin_num == 7 || bank_pin_num == 8))
+ return -EINVAL;
+
+ /* clear the bit in direction mode reg to set the pin as input */
+ reg = readl_relaxed(gpio->base_addr + ZYNQ_GPIO_DIRM_OFFSET(bank_num));
+ reg &= ~BIT(bank_pin_num);
+ writel_relaxed(reg, gpio->base_addr + ZYNQ_GPIO_DIRM_OFFSET(bank_num));
+
+ return 0;
+}
+
+/**
+ * zynq_gpio_dir_out - Set the direction of the specified GPIO pin as output
+ * @chip: gpio_chip instance to be worked on
+ * @pin: gpio pin number within the device
+ * @state: value to be written to specified pin
+ *
+ * This function sets the direction of specified GPIO pin as output, configures
+ * the Output Enable register for the pin and uses zynq_gpio_set to set
+ * the state of the pin to the value specified.
+ *
+ * Return: 0 always
+ */
+static int zynq_gpio_dir_out(struct gpio_chip *chip, unsigned int pin,
+ int state)
+{
+ u32 reg;
+ unsigned int bank_num, bank_pin_num;
+ struct zynq_gpio *gpio = container_of(chip, struct zynq_gpio, chip);
+
+ if (zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio) < 0)
+ return -EINVAL;
+
+ /* set the GPIO pin as output */
+ reg = readl_relaxed(gpio->base_addr + ZYNQ_GPIO_DIRM_OFFSET(bank_num));
+ reg |= BIT(bank_pin_num);
+ writel_relaxed(reg, gpio->base_addr + ZYNQ_GPIO_DIRM_OFFSET(bank_num));
+
+ /* configure the output enable reg for the pin */
+ reg = readl_relaxed(gpio->base_addr + ZYNQ_GPIO_OUTEN_OFFSET(bank_num));
+ reg |= BIT(bank_pin_num);
+ writel_relaxed(reg, gpio->base_addr + ZYNQ_GPIO_OUTEN_OFFSET(bank_num));
+
+ /* set the state of the pin */
+ zynq_gpio_set_value(chip, pin, state);
+ return 0;
+}
+
+/**
+ * zynq_gpio_get_direction - Read the direction of the specified GPIO pin
+ * @chip: gpio_chip instance to be worked on
+ * @pin: gpio pin number within the device
+ *
+ * This function returns the direction of the specified GPIO.
+ *
+ * Return: 0 for output, 1 for input
+ */
+static int zynq_gpio_get_direction(struct gpio_chip *chip, unsigned int pin)
+{
+ u32 reg;
+ unsigned int bank_num, bank_pin_num;
+ struct zynq_gpio *gpio = container_of(chip, struct zynq_gpio, chip);
+
+ if (zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio) < 0)
+ return -EINVAL;
+
+ reg = readl_relaxed(gpio->base_addr + ZYNQ_GPIO_DIRM_OFFSET(bank_num));
+
+ return !(reg & BIT(bank_pin_num));
+}
+
+static struct gpio_ops zynq_gpio_ops = {
+ .direction_input = zynq_gpio_dir_in,
+ .direction_output = zynq_gpio_dir_out,
+ .get = zynq_gpio_get_value,
+ .set = zynq_gpio_set_value,
+ .get_direction = zynq_gpio_get_direction,
+};
+
+static int zynqmp_gpio_probe(struct device_d *dev)
+{
+ struct resource *iores;
+ struct zynq_gpio *gpio;
+ const struct zynq_platform_data *p_data;
+ int ret;
+
+ gpio = xzalloc(sizeof(*gpio));
+ p_data = device_get_match_data(dev);
+ iores = dev_request_mem_resource(dev, 0);
+ if (IS_ERR(iores)) {
+ ret = PTR_ERR(iores);
+ goto free_gpio;
+ }
+
+ gpio->base_addr = IOMEM(iores->start);
+ gpio->chip.base = of_alias_get_id(dev->device_node, "gpio");
+ gpio->chip.ops = &zynq_gpio_ops;
+ gpio->chip.ngpio = p_data->ngpio;
+ gpio->chip.dev = dev;
+ gpio->p_data = p_data;
+
+ return gpiochip_add(&gpio->chip);
+
+free_gpio:
+ kfree(gpio);
+ return ret;
+}
+
+static const struct zynq_platform_data zynqmp_gpio_def = {
+ .quirks = GPIO_QUIRK_DATA_RO_BUG,
+ .ngpio = ZYNQMP_GPIO_NR_GPIOS,
+ .max_bank = ZYNQMP_GPIO_MAX_BANK,
+ .bank_min[0] = ZYNQ_GPIO_BANK0_PIN_MIN(MP),
+ .bank_max[0] = ZYNQ_GPIO_BANK0_PIN_MAX(MP),
+ .bank_min[1] = ZYNQ_GPIO_BANK1_PIN_MIN(MP),
+ .bank_max[1] = ZYNQ_GPIO_BANK1_PIN_MAX(MP),
+ .bank_min[2] = ZYNQ_GPIO_BANK2_PIN_MIN(MP),
+ .bank_max[2] = ZYNQ_GPIO_BANK2_PIN_MAX(MP),
+ .bank_min[3] = ZYNQ_GPIO_BANK3_PIN_MIN(MP),
+ .bank_max[3] = ZYNQ_GPIO_BANK3_PIN_MAX(MP),
+ .bank_min[4] = ZYNQ_GPIO_BANK4_PIN_MIN(MP),
+ .bank_max[4] = ZYNQ_GPIO_BANK4_PIN_MAX(MP),
+ .bank_min[5] = ZYNQ_GPIO_BANK5_PIN_MIN(MP),
+ .bank_max[5] = ZYNQ_GPIO_BANK5_PIN_MAX(MP),
+};
+
+static const struct zynq_platform_data zynq_gpio_def = {
+ .quirks = ZYNQ_GPIO_QUIRK_IS_ZYNQ | GPIO_QUIRK_DATA_RO_BUG,
+ .ngpio = ZYNQ_GPIO_NR_GPIOS,
+ .max_bank = ZYNQ_GPIO_MAX_BANK,
+ .bank_min[0] = ZYNQ_GPIO_BANK0_PIN_MIN(),
+ .bank_max[0] = ZYNQ_GPIO_BANK0_PIN_MAX(),
+ .bank_min[1] = ZYNQ_GPIO_BANK1_PIN_MIN(),
+ .bank_max[1] = ZYNQ_GPIO_BANK1_PIN_MAX(),
+ .bank_min[2] = ZYNQ_GPIO_BANK2_PIN_MIN(),
+ .bank_max[2] = ZYNQ_GPIO_BANK2_PIN_MAX(),
+ .bank_min[3] = ZYNQ_GPIO_BANK3_PIN_MIN(),
+ .bank_max[3] = ZYNQ_GPIO_BANK3_PIN_MAX(),
+};
+
+static const struct of_device_id zynq_gpio_of_match[] = {
+ { .compatible = "xlnx,zynq-gpio-1.0", .data = &zynq_gpio_def },
+ { .compatible = "xlnx,zynqmp-gpio-1.0", .data = &zynqmp_gpio_def },
+ { /* end of table */ }
+};
+
+static struct driver_d zynqmp_gpio_driver = {
+ .name = "zynqmp-gpio",
+ .of_compatible = zynq_gpio_of_match,
+ .probe = zynqmp_gpio_probe,
+};
+
+postcore_platform_driver(zynqmp_gpio_driver);
--
2.17.1
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH v2 0/1] gpio: add driver for xilinx zynq and zynqmp
2021-10-13 11:22 [PATCH v2 0/1] gpio: add driver for xilinx zynq and zynqmp Michael Riesch
2021-10-13 11:22 ` [PATCH v2 1/1] " Michael Riesch
@ 2021-10-14 11:57 ` Sascha Hauer
1 sibling, 0 replies; 3+ messages in thread
From: Sascha Hauer @ 2021-10-14 11:57 UTC (permalink / raw)
To: Michael Riesch; +Cc: barebox
On Wed, Oct 13, 2021 at 01:22:46PM +0200, Michael Riesch wrote:
> Hi all,
>
> This patch adds a GPIO driver for the Xilinx Zynq/Zynq
> UltraScale+ MPSoC architecture based on the corresponding
> driver in the Linux kernel.
>
> The work was mainly carried out by Thomas Haemmerle, with
> several format fixes and the revisions for v2 applied by me.
> Version 2 of this patch considers the review by Ahmad
> Fatoum.
>
> Tested on the ZCU106 evaluation board as well as on a
> custom Zynq UltraScale+ MPSoC board.
>
> Best regards,
> Michael
>
> Thomas Haemmerle (1):
> gpio: add driver for xilinx zynq and zynqmp
Applied, thanks
Sascha
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2021-10-14 11:58 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-10-13 11:22 [PATCH v2 0/1] gpio: add driver for xilinx zynq and zynqmp Michael Riesch
2021-10-13 11:22 ` [PATCH v2 1/1] " Michael Riesch
2021-10-14 11:57 ` [PATCH v2 0/1] " Sascha Hauer
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox